BASES FOR SOAKWELLS & LINERS - Maddington Concrete · 2019-11-07 · MADDINGTON CONCRETE PRODUCTS Pty Ltd Maddington Concrete Products Pty Ltd 66 Kelvin Road Maddington, WA 6109 Ph

MADDINGTON CONCRETE PRODUCTS Pty Ltd

Maddington Concrete Products Pty Ltd 66 Kelvin Road Maddington, WA 6109 Ph (08) 9459 1053

EMAIL: [email protected] WEB: www.maddingtonconcrete.com.au Manufacturers of: *Soakwells*Septic Tanks *Leach Drains *Pipes *Well Liners, Covers etc. 2018 CATALOGUE (EDITIED 03-04-2019)

1 | P a g e

BASES FOR SOAKWELLS & LINERS SOLID BASE

CODE SIZE/ DESCRIPTION

DIAMETER X THICKNESS (MM) (MM)

# LIFTING POINTS

(1.3 tonne) (EACH)

WEIGHT

(KG) A B D37 2000 X 150 2 1280 D38 1700 X 150 2 825 D39 1450 X 130 1 475 D39C 1240 X 130 1 400 D40 1150 X 130 1 290 D41D 760 X 60 1 60

BASE WITH WEEP HOLE



WEEP HOLE Ø (APPROX.MM)

# LIFTING POINTS

(1.3 tonne)

(EACH)

WEIGHT

(KG)

A B D37A 2000 X 150 130-150 2 1175 D38A 1700 X 150 130-150 2 800 D39A 1450 X 130 130-150 2 465 D39D 1240 X 130 130-150 2 380 D40A 1150 X 130 130-150 2 285 D41B 760 X 130 130-150 1 90

***Weights & Measurements are a guide only. Some variations will occur

mailto:[email protected]

http://www.maddingtonconcrete.com.au/




2 | P a g e

BASES FOR SOAKWELLS & LINERS – CONT. BASE WITH LARGE DRAINAGE HOLE



HOLE Ø

(MM)

# LIFTING POINTS (1.3 tonne)

(EACH)

WEIGHT

(KG) A B D37B 2000 X 150 1200 2 785 D38B 1700 X 150 900 2 580 D39B 1450 X 130 600 2 390 D39 1240 X 130 600 2 320 D40AA 1150 X 130 600 2 200







3 | P a g e

COVERS - NON TRAFFIC WITH CONCRETE ROUND ACCESS (Class A) MANHOLE COVER

MANHOLE – CHEQUER PLATE **

CODE

SIZE

DIAMETER X THICKNESS

(MM) (MM)

CONCRETE ACCESS Ø

CLEAR OPENING

(MM)

ACCESS OFFSET FROM

EDGE (APPROX)

(MM)

# LIFTING POINTS

(1.3 TONNE)

(EACH)

WEIGHT

(KG) A B C D D33 2000 X 150 604 300-400 3 1200 D28B 1350 X 150 604 300-400 3 460 D30B 1000 X 150 604 300-400 3 240 D28C **1220 X 150 600 (CHEQUER PLATE PATTERN) 300-400 (2 ON THE SIDE) 400







4 | P a g e

COVERS - SQUARE NON TRAFFIC WITH CONCRETE ROUND ACCESS (Class A)

CODE

SIZE

WIDTH X LENGTH X THICKNESS

(MM) (MM) (MM)

CONCRETE ACCESS Ø

CLEAR OPENING

(MM)

# LIFTING POINTS

(1.3 TONNE)

(EACH)

WEIGHT

(KG)

A B C D D28 1350 X 1350 X 150 604 2 645 D29 1200 X 1200 X 150 604 2 585 D30 1050 X 1050 X 150 604 2 315

** PLEASE NOTE: Concrete Insert is NON TRAFFICABLE ***Weights & Measurements are a guide only. Some variations will occur






5 | P a g e

COVERS - NON TRAFFIC WITH CONCRETE ROUND ACCESS MARKED ELECTRICAL OR COMMUNICATION (CLASS A)

CODE

SIZE


CONCRETE ACCESS CLEAR OPENING Ø

(MM)

ACCESS DISTANCE FROM EDGE (APPROX)

(MM)

# LIFTING POINTS (1.3 TONNE)

(EACH)

WEIGHT

(KG) A B C D D60 1350 X 150 - ELECTRICAL 604 300-400 3 460 D62 1000 X 150 - ELECTRICAL 604 300-400 3 240

CODE

SIZE


CONCRETE ACCESS CLEAR OPENING Ø

(MM)

ACCESS DISTANCE FROM EDGE (APPROX)

(MM)


(EACH)

WEIGHT

(KG) A B C D D61 1350 X 150 - COMMUNICATION 604 300-400 3 460 D63 1000 X 150 - COMMUNICATION 604 300-400 3 240







6 | P a g e

COVERS – TRAFFIC with CAST IRON ROUND SOLID ACCESS (CLASS D, 8 TONNE WHEEL LOAD RATING)

FLUSH

CODE SIZE

DIAMETER X THICKNESS FRAME HEIGHT (mm) (mm)

CAST IRON COVER/FRAME OVERALL SIZE

(mm)

OPENING CLEARANCE SIZE Ø

(mm)

# LIFTING POINTS (1.3 Tonne)

(Each)

WEIGHT

(kg) A B C D54 2000 X 150 with FLUSH COVER 672 604 2 1170 D55 1650 X 150 with FLUSH COVER 672 604 2 780 D56 1350 X 150 with FLUSH COVER 672 604 2 470 D57 1000 X 150 with FLUSH COVER 672 604 2 230

RAISED 25MM

CODE SIZE



(mm)


(mm)


(Each)

WEIGHT

(kg) A B C D54A 2000 X 150 with 25mm RAISED COVER 672 604 2 1170 D55A 1650 X 150 with 25mm RAISED COVER 672 604 2 780 D56A 1350 X 150 with 25mm RAISED COVER 672 604 2 470 D57A 1000 X 150 with 25mm RAISED COVER 672 604 2 230







7 | P a g e

COVERS – TRAFFIC with CAST IRON ROUND SOLID ACCESS (CLASS D , 8 TONNE WHEEL LOAD RATING)

RAISED 40MM

CODE SIZE



(mm)


(mm)


(Each)

WEIGHT

(kg) A B C D54AA 2000 X 150 with 40mm RAISED COVER 672 604 2 1170 D55AA 1650 X 150 with 40mm RAISED COVER 672 604 2 780 D56AA 1350 X 150 with 40mm RAISED COVER 672 604 2 470 D57AA 1000 X 150 with 40mm RAISED COVER 672 604 2 230

RAISED 100MM

CODE SIZE



(mm)


(mm)


(Each)

WEIGHT

(kg) A B C D54B 2000 X 150 with 100mm RAISED COVER 672 604 2 1170 D55B 1650 X 150 with 100mm RAISED COVER 672 604 2 780 D56B 1350 X 150 with 100mm RAISED COVER 672 604 2 470 D57B 1000 X 150 with 100mm RAISED COVER 672 604 2 230







8 | P a g e

COVERS – TRAFFIC with CAST IRON ROUND SOLID ACCESS (CLASS D , 8 TONNE WHEEL LOAD RATING)

LOOSE COVER

CODE SIZE


CAST IRON GRATE/FRAME OVERALL SIZE

(mm)


(mm)


(each)

WEIGHT

(kg) A B C D D54C 2000 X 150 with LOOSE 75MM COVER 672 604 2 1170 D54D 2000 X 150 with LOOSE 125MM COVER 672 604 2 1175 D55C 1650 X 150 with LOOSE 75MM COVER 672 604 2 780 D55D 1650 X 150 with LOOSE 125MM COVER 672 604 2 785 D56C 1350 X 150 with LOOSE 75MM COVER 672 604 2 470 D56D 1350 X 150 with LOOSE 125MM COVER 672 604 2 475 D57C 1000 X 150 with LOOSE 75MM COVER 672 604 2 230 D57D 1000 X 150 with LOOSE 125MM COVER 672 604 2 235

**Concrete Cover supplied with a hole in centre. Grate supplied as a separate item, so that the rising can be determined on site, as required by contractor. ***Weights & Measurements are a guide only. Some variations will occur






9 | P a g e

COVERS TRAFFIC- With CAST IRON ROUND SOLID ACCESS MARKED ELECTRICAL OR COMMUNICATIONS (CLASS D, 8 TONNE WHEEL LOAD RATING)

CODE

SIZE

DIAMETER X THICKNESS (mm) (mm)


(mm)

OPENING CLEARANCE

SIZE Ø

(mm)

ACCESS OFFSET FROM EDGE

(APPROX)

(mm)


(each)

WEIGHT

(kg) A B C D D71A 2000 DIAMETER X 150MM - ELECTRICAL 672 604 300-400 2 1170 D70A 1650 DIAMETER X 150MM - ELECTRICAL 672 604 300-400 2 780 D60A 1350 DIAMETER X 150MM - ELECTRICAL 672 604 300-400 2 470 D62A 1000 DIAMETER X 150MM - ELECTRICAL 672 604 300-400 2 230

CODE

SIZE

DIAMETER X THICKNESS

(mm) (mm)


(mm)

OPENING CLEARANCE

SIZE Ø

(mm)

ACCESS OFFSET FROM EDGE

(APPROX)

(mm)


(each)

WEIGHT

(kg) A B C D D61A 1350 DIAMETER X 150MM - COMMUNICATION 672 604 300-400 2 470 D63A 1000 DIAMETER X 150MM - COMMUNICATION 672 604 300-400 2 230







10 | P a g e

COVERS – TRAFFIC with GALVANISED SQUARE GRATE (HINGED & BOLT DOWN) CLASS C, 5 TONNE WHEEL LOAD RATING

FLUSH

CODE SIZE


GRATE/ FRAME OVERALL SIZE

LENGTH X WIDTH (mm) (mm)

OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19 2000 X 150 with FLUSH Grate 550 X 550 535 X 435 2 1160 D21 1650 X 150 with FLUSH Grate 550 X 550 535 X 435 2 750 D22 1350 X 150 with FLUSH Grate 550 X 550 535 X 435 2 460 D24 1000 X 150 with FLUSH Grate 450 X 450 445 X 355 2 240 D25 760 X 150 with FLUSH Grate 350 X 350 325 X 265 2 110

RAISED 25MM

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19A 2000 X 150 with 25mm RAISED Grate 550 X 550 535 X 435 2 1160 D21A 1650 X 150 with 25mm RAISED Grate 550 X 550 535 X 435 2 750 D22A 1350 X 150 with 25mm RAISED Grate 550 X 550 535 X 435 2 460 D24A 1000 X 150 with 25mm RAISED Grate 450 X 450 445 X 355 2 240 D25A 760 X 150 with 25mm RAISED Grate 350 X 350 325 X 265 1 110







11 | P a g e

COVERS – TRAFFIC with GALVANISED SQUARE GRATE (HINGED & BOLT DOWN) CLASS C, 5 TONNE WHEEL LOAD RATING

RAISED 40MM

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19AA 2000 X 150 with 40mm RAISED Grate 550 X 550 535 X 435 2 1160 D21AA 1650 X 150 with 40mm RAISED Grate 550 X 550 535 X 435 2 750 D22AA 1350 X 150 with 40mm RAISED Grate 550 X 550 535 X 435 2 460 RAISED 100MM

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19C 2000 X 150 With 100mm RAISED Grate 550 X 550 535 X 435 2 1200 D21C 1650 X 150 With 100mm RAISED Grate 550 X 550 535 X 435 2 770 D22C 1350 X 150 With 100mm RAISED Grate 550 X 550 535 X 435 2 480 D24C 1000 X 150 With 100mm RAISED Grate 450 X 450 445 X 355 2 260







12 | P a g e

COVERS – TRAFFIC with GALVANISED SQUARE GRATE

(HINGED & BOLT DOWN) CLASS C, 5 TONNE WHEEL LOAD RATING

LOOSE

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19B 2000 X 150 With LOOSE Grate 550 X 550 535 X 435 2 1160 D21B 1650 X 150 With LOOSE Grate 550 X 550 535 X 435 2 750 D22B 1350 X 150 With LOOSE Grate 550 X 550 535 X 435 2 460 D24B 1000 X 150 With LOOSE Grate 450 X 450 445 X 355 2 240 D25B 760 X 150 With LOOSE Grate 350 X 350 325 X 265 1 110







13 | P a g e

COVERS – TRAFFIC with GALVANISED RECTANGLE GRATE (BICYCLE SAFE, HINGED & BOLT DOWN) CLASS D, 8 TONNE WHEEL LOAD RATING FLUSH

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19D 2000 X 150 with FLUSH Grate 760 X 545 750 X 445 2 1185 D21D 1650 X 150 with FLUSH Grate 760 X 545 750 X 445 2 770 D22D 1350 X 150 with FLUSH Grate 760 X 545 750 X 445 2 480 D23D 1050 SQUARE X 150 with FLUSH Grate 760 X 545 750 X 445 2 350 RAISED 40MM

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19E 2000 X 150 with 40mm RAISED Grate 760 X 545 750 X 445 2 1185 D21E 1650 X 150 with 40mm RAISED Grate 760 X 545 750 X 445 2 770 D22E 1350 X 150 with 40mm RAISED Grate 760 X 545 750 X 445 2 480 D23E 1050 SQUARE X 150 with 40mm RAISED Grate 760 X 545 750 X 445 2 350







14 | P a g e

COVERS – TRAFFIC with GALVANISED RECTANGLE GRATE (BICYCLE SAFE, HINGED & BOLT DOWN) CLASS D, 8 TONNE WHEEL LOAD RATING

RAISED 100MM

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19F 2000 X 150 with 100mm RAISED Grate 760 X 545 750 X 445 2 1185 D21F 1650 X 150 with 100mm RAISED Grate 760 X 545 750 X 445 2 770 D22F 1350 X 150 with 100mm RAISED Grate 760 X 545 750 X 445 2 480 D23F 1050 SQUARE X 150 with 100mm RAISED Grate 760 X 545 750 X 445 2 355

LOOSE

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D D19G 2000 X 150 with LOOSE Grate 760 X 545 750 X 445 2 1185







15 | P a g e

COVERS – TRAFFIC SQUARE WITH GALVANISED SQUARE GRATE (BICYCLE SAFE, HINGED & BOLT DOWN) CLASS C, 5 TONNE WHEEL LOAD RATING

(MADE TO ORDER)

FLUSH

CODE SIZE

WIDTH X LENGTH X THICKNESS FRAME HEIGHT (mm) (mm) (mm)



OPENING SIZE



(each)

WEIGHT

(kg) A B C D E D14 1350 X 1350 X 150 with FLUSH Grate 550 X 550 535 X 435 2 610 D15 1200 X 1200 X 150 with FLUSH Grate 550 X 550 535 X 435 2 475 D16 1050 X 1050 X 150 with FLUSH Grate 550 X 550 535 X 435 2 350 D17A 750 X 750 X 150 with FLUSH Grate 450 X 450 445 X 355 2 160

RAISED 25MM

CODE SIZE




OPENING SIZE LENGTH X WIDTH

(mm) (mm)


(each)

WEIGHT

(kg) A B C D E D14A 1350 X 1350 X 150 with 25mm RAISED GRATE 550 X 550 535 X 435 2 610 D15A 1200 X 1200 X 150 with 25mm RAISED GRATE 550 X 550 535 X 435 2 475 D16A 1050 X 1050 X 150 with 25mm RAISED GRATE 550 X 550 535 X 435 2 350 D17B 750 X 750 X 150 with 25mm RAISED GRATE 450 X 450 445 X 355 2 160







16 | P a g e

COVERS – TRAFFIC SQUARE WITH GALVANISED SQUARE GRATE (BICYCLE SAFE, HINGED & BOLT DOWN) CLASS C, 5 TONNE WHEEL LOAD RATING

(MADE TO ORDER)

RAISED 100MM

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D E D14C 1350 X 1350 X 150 with 100mm RAISED GRATE 550 X 550 535 X 435 2 610 D15C 1200 X 1200 X 150 with 100mm RAISED GRATE 550 X 550 535 X 435 2 475 D16C 1050 X 1050 X 150 with 100mm RAISED GRATE 550 X 550 535 X 435 2 350 D17D 750 X 750 X 150 with 100mm RAISED GRATE 450 X 450 445 X 355 2 160

LOOSE

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B C D E D14B 1350 X 1350 X 150 with LOOSE GRATE 550 X 550 535 X 435 2 610 D15B 1200 X 1200 X 150 with LOOSE GRATE 550 X 550 535 X 435 2 475 D16B 1050 X 1050 X 150 with LOOSE GRATE 550 X 550 535 X 435 2 350 D17C 750 X 750 X 150 with LOOSE GRATE 450 X 450 445 X 355 2 160







17 | P a g e

COVERS – TRAFFIC with HEELPROOF GALVANISED GRATE

(BOLT DOWN) CLASS D, 8 TONNE WHEEL LOAD RATING

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B E C D D19HEEL 2000 X 150 with 40mm RAISED Grate 700 X 700 600 X 600 2 1200 D19HEELA 2000 X 150 with 100mm RAISED Grate 700 X 700 600 X 600 2 1200 D21HEEL 1650 X 150 with 40mm RAISED Grate 700 X 700 600 X 600 2 770 D21HEELA 1650 X 150 with 100mm RAISED Grate 700 X 700 600 X 600 2 770 D22HEEL 1350 X 150 with 40mm RAISED Grate 700 X 700 600 X 600 2 600 D22HEELA 1350 X 150 with 100mm RAISED Grate 700 X 700 600 X 600 2 630 D23HEEL 1050 X 150 with 40mm RAISED Grate 700 X 700 600 X 600 2 300 D23HEELA 1050 X 150 with 100mm RAISED Grate 700 X 700 600 X 600 2 300







18 | P a g e

COVERS- BUBBLE UP GRATED WITH GALVANISED GRATE


CODE

SIZE


GRATE HEIGHT

(mm)

GRATE/FRAME OVERALL SIZE

LENGTH x WIDTH (mm) (mm)

OPENING SIZE

LENGTH X WIDTH

(mm) (mm)

# LIFTING POINTS

(1.3 tonne)

(each)

WEIGHT

(kg) A B C D E D80 2000 x 150 175 760 x 545 750 x 445 2 1200 D81 1650 x 150 175 760 x 545 750 x 445 2 770 D82 1350 x 150 175 760 x 545 750 x 445 2 630 D83 1050 SQUARE x 150 175 760 x 545 750 x 445 2 360






19 | P a g e

COVERS – TRAFFIC with ROUND CAST IRON GRATE (CLASS D , 8 TONNE WHEEL LOAD RATING) FLUSH

CODE SIZE



(mm)


(mm)


(each)

WEIGHT

(kg) A B C D D50 2000 X 150 with FLUSH Grate 672 604 2 1170 D51 1650 X 150 with FLUSH Grate 672 604 2 780 D52 1350 X 150 with FLUSH Grate 672 604 2 470 D53 1000 X 150 with FLUSH Grate 672 604 2 230

RAISED 25MM

CODE SIZE



(mm)


(mm)


(each)

WEIGHT

(kg) A B C D D50A 2000 X 150 with 25mm RAISED GRATE 672 604 2 1170 D51A 1650 X 150 with 25mm RAISED GRATE 672 604 2 780 D52A 1350 X 150 with 25mm RAISED GRATE 672 604 2 470 D53A 1000 X 150 with 25mm RAISED GRATE 672 604 2 230







20 | P a g e

COVERS – TRAFFIC with ROUND CAST IRON GRATE (CLASS D , 8 TONNE WHEEL LOAD RATING) RAISED 40MM

CODE SIZE



(mm)


(mm)


(each)

WEIGHT

(kg) A B C D50AA 2000 X 150 with 40mm RAISED GRATE 672 604 2 1170 D51AA 1650 X 150 with 40mm RAISED GRATE 672 604 2 780 D52AA 1350 X 150 with 40mm RAISED GRATE 672 604 2 470 D53AA 1000 X 150 with 40mm RAISED GRATE 672 604 2 230

RAISED 100MM

CODE SIZE



(mm)


(mm)


(each)

WEIGHT

(kg) A B C D50B 2000 X 150 with 100mm RAISED GRATE 672 604 2 1170 D51B 1650 X 150 with 100mm RAISED GRATE 672 604 2 780 D52B 1350 X 150 with 100mm RAISED GRATE 672 604 2 470 D53B 1000 X 150 with 100mm RAISED GRATE 672 604 2 230







21 | P a g e

COVERS – TRAFFIC with ROUND CAST IRON GRATE (CLASS D , 8 TONNE WHEEL LOAD RATING)

LOOSE GRATE

CODE SIZE



(mm)


(mm)


(each)

WEIGHT

(kg) A B C D50C 2000 X 150 with LOOSE 75MM GRATE 672 604 2 1170 D50D 2000 X 150 with LOOSE 125MM GRATE 672 604 2 1175 D51C 1650 X 150 with LOOSE 75MM GRATE 672 604 2 780 D51D 1650 X 150 with LOOSE 125MM GRATE 672 604 2 785 D52C 1350 X 150 with LOOSE 75MM GRATE 672 604 2 470 D52D 1350 X 150 with LOOSE 125MM GRATE 672 604 2 475 D53C 1000 X 150 with LOOSE 75MM GRATE 672 604 2 230 D53D 1000 X 150 with LOOSE 125MM GRATE 672 604 2 235







22 | P a g e

COVERS – TRAFFIC with CAST IRON WAVE GRATE (BOLT DOWN) CLASS D, 8 TONNE WHEEL LOAD RATING FLUSH

CODE SIZE




OPENING SIZE



(each)

WEIGHT

(kg) A B E C D D45 2000 X 150 with FLUSH Grate 750 X 550 660 X 450 2 1200 D46 1650 X 150 with FLUSH Grate 750 X 550 660 X 450 2 750 D47 1350 X 150 with FLUSH Grate 750 X 550 660 X 450 2 610

RAISED 40 / 100MM

CODE SIZE




OPENING SIZE LENGTH X WIDTH

(mm) (mm)


(each)

WEIGHT

(kg) A B E C D D45AA 2000 X 150 with 40mm RAISED Grate 750 X 550 660 X 450 2 1200 D46AA 1650 X 150 with 40mm RAISED Grate 750 X 550 660 X 450 2 770 D47AA 1350 X 150 with 40mm RAISED Grate 750 X 550 660 X 450 2 630 D45B 2000 X 150 with 100mm RAISED Grate 750 X 550 660 X 450 2 1200 D46B 1650 X 150 with 100mm RAISED Grate 750 X 550 660 X 450 2 770 D47B 1350 X 150 with 100mm RAISED Grate 750 X 550 660 X 450 2 630







23 | P a g e

COVERS- SIDE ENTRY

SIDE ENTRY APRON/S

CODE

SIZE

LENGTH X WIDTH X THICKNESS (mm) (mm) (mm) (mm)

# LIFTING POINTS

(1.3 TONNE)

(each)

WEIGHT

(kg) A B C D D26B PLAIN 1880 X 1350 X 145 230 2 750 D26D LEFT ENTRY 1880 X 1350 X 145 230 2 750 D26C RIGHT ENTRY 1880 X 1350 X 145 230 2 750







24 | P a g e

COVERS - SIDE ENTRY (CONT’)

SIDE ENTRY FRAME

CODE

SIZE

LENGTH X WIDTH X THICKNESS (mm) (mm) (mm)

# LIFTING POINTS

(1.3 TONNE)

(each)

WEIGHT

(kg) A B C D26 1240 X 780 X 150 2 140

SIDE ENTRY COVER

CODE

SIZE

LEGTH X WIDTH X THICKNESS (mm) (mm) (mm)

WEIGHT

(kg) A B C D26A 1000 X 610 X 50 105







25 | P a g e

COVERS – STANDARD - Non traffic 1 piece

CODE

SIZES


# LIFTING POINTS

(1.3 tonne)

(each)

WEIGHT

(kg) A B D01 1650 (1675) x 70 2 390 D03 1350 x 70 1 230 D05 1000 x 70 1 125 D06A 760 x 70 1 80 D06 700 x 60 1 50

COVERS – STANDARD - Non traffic 2 piece

CODE

SIZES


# LIFTING POINTS

(1.3 tonne)

(each)

WEIGHT

(kg) A B D01A 1650 X 70 1 each piece 180 each piece D03A 1350 X 70 1 each piece 130 each piece

• Please Note: All Standard Covers are only suitable for Pedestrian use only.







26 | P a g e

COVERS – TRAFFIC 1 piece (class D, 8 tonne)

CODE

SIZES DIAMETER X THICKNESS

(mm) (mm)

# LIFTING POINTS

(1.3 tonne)

(each)

WEIGHT

(Kg) A B D07 2000 X 150 2 1230 D08 1650 X 150 2 830 D10 1350 X 150 1 545 D12 1000 X 150 1 280 D13 760 X 150 1 160

COVERS – TRAFFIC 2 piece (class C, 5 tonne)

CODE

SIZES DIAMETER X THICKNESS

(mm) (mm)

# LIFTING POINTS

(1.3 tonne)

(mm)

WEIGHT

(kg) A B D07A 2000 X 150 2 each piece 620 each piece D08A 1650 X 150 1 each piece 400 each piece D10A 1350 X 150 1 each piece 250 each piece







27 | P a g e

LINERS/SILT PITS

1800 mm Ø INTERLOCKING (WALL THICKNESS 90mm)

CODE

SIZES

INTERNAL Ø X DEPTH (mm) (mm)

CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B D90 1800 X 1800 4580 2400 D90A 1800 X 1800 w/base cast in 4390 3600 D91 1800 X 1500 3816 2000 D91A 1800 X 1500 w/base cast in 3625 3100 E0 1800 X 1200 3050 1530 E 1800 X 1200 w/base cast in 2863 2630 E00 1800 X 900 2290 1140 E00AA 1800 X 900 w/base cast in 2100 2240 E01 1800 X 600 1525 750 E01AA 1800 X 600 w/base cast in 1336 1850 E01B 1800 X 300 763 420

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x Lifting/Piping Holes approx.100mm diameter, located approx. 220mm from top of tank

(C) • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size and Separate Base size suitable are 2000mm diameter. • Please contact your local council for the sizing requirements for your area.







28 | P a g e

LINERS/SILT PITS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B E02 1500 X 1500 2650 1400 E02B 1500 X 1500 w/base cast in 2518 1840 E03 1500 X 1200 2120 1100 E03B 1500 X 1200 w/base cast in 1985 1500 E03C 1500 X 900 1590 800 E03E 1500 X 900 w/base cast in 1455 1200 E04 1500 X 600 1060 520 E04A 1500 X 300 530 300

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • All Liners have 2 x 100mm Knock out Holes located approx. 180mm from Top of Tank(C) • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1650mm and Base size suitable is 1700mm diameter • Please contact your local council for the sizing requirements for your area.







29 | P a g e

LINERS/SILT PITS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg)

A B E05 1200 X 1500 1697 1100 E04BB 1200 X 1500 w/base cast in 1610 1400 E06 1200 X 1200 1357 880 E05A 1200 X 1200 w/base cast in 1270 1200 E06A 1200 X 900 1018 650 E06AA 1200 X 900 w/base cast in 930 900 E07 1200 X 600 678 430 E07A 1200 X 300 339 220

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • All Liners have 2 x 100mm Knock out Holes located approx. 110-180mm from Top of Tank(C) • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1350mm and Base size suitable is 1450mm diameter. • Please contact your local council for the sizing requirements for your area.







30 | P a g e

LINERS/SILT PITS


• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • THERE ARE NO PIPING HOLES IN THIS PRODUCT RANGE • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1000mm and Base size suitable is 1150mm diameter • Please contact your local council for the sizing requirements for your area.


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B E10 900 X 1200 763 530 E10A 900 X 1200 w/base cast in 700 700 E11 900 X 900 572 400 E11A 900 X 900 w/base cast in 510 540 E12 900 X 600 381 260 E12C 900 X 600 w/base cast in 320 350 E12A 900 X 300 190 150






31 | P a g e

LINERS/SILT PITS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B E13 600 X 1200 340 330 E14 600 X 900 250 270 E14A 600 X 900 w/base cast in 225 310 E16 600 X 600 170 180 E16A 600 X 600 w/base cast in 145 220

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • THERE ARE NO PIPING HOLES IN THIS PRODUCT RANGE • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size/s suitable are 700mm or 760mm and Base size suitable is 760mm diameter • Please contact your local council for the sizing requirements for your area.







32 | P a g e

LINERS/SILT PITS- WITH STEP IRON HOLES


CODE

SIZES


CAPACITY

FULL HEIGHT

(Ltrs)

WEIGHT

(Kg)

A B D90B 1800 X 1800 (pictured) 4580 2400 D91B 1800 X 1500 3816 2000 E00A 1800 X 1200 3050 1530 E00B 1800 X 900 2290 1140 E01A 1800 X 600 1525 750

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x Lifting/Piping Holes approx.100mm diameter, located approx. 220mm from

top of tank (C) • Step hole positions are located approx.150mm from top & bottom (D,E) at intervals of 300mm (F) • STEPS ARE BOLT - ON type • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size and Separate Base size suitable are 2000mm diameter. • Please contact your local council for the sizing requirements for your area.







33 | P a g e



CODE

SIZES

Internal Ø X Depth (mm) (mm)

CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B E02A 1500 X 1500 2650 1400 E03A 1500 X 1200 (pictured) 2120 1100 E03D 1500 X 900 1590 800 E04AA 1500 X 600 1060 520

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • All Liners have 2 x 100mm Knock out Holes located approx. 180mm from Top of Tank(C) • Step hole positions are located approx.150mm from top & bottom (D,E) at intervals of 300mm (F) • STEPS ARE BOLT - ON type • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1650mm dia and Separate Base size suitable is 1700mm diameter. • Please contact your local council for the sizing requirements for your area.







34 | P a g e



CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg)

A B E04B 1200 X 1500 1697 1100 E06B 1200 X 1200 (pictured) 1357 880 E06D 1200 X 900 1018 650 E07B 1200 X 600 678 430

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • All Liners have 2 x 100mm Knock out Holes located approx. 180mm from Top of Tank(C) • Step hole positions are located approx.150mm from top & bottom (D,E) at intervals of 300mm (F) • STEPS ARE BOLT - ON type • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1350mm and Base size suitable is 1450mm diameter. • Please contact your local council for the sizing requirements for your area.







35 | P a g e



CODE

SIZES Internal Ø X Depth (mm) (mm)

CAPACITY

FULL HEIGHT (ltrs)

WEIGHT

(kg)

A B E09 1050 X 1200 1040 670 E08 1050 X 1200 w/base cast in (pictured) 960 830 E09A 1050 X 900 780 510 E09AA 1050 X 900 w/base cast in 690 670 E09B 1050 X 600 520 350 E09BB 1050 X 600 w/base cast in 440 510 E09C 1050 X 300 260 170

• The step holes in this liner need to be knocked out if using step irons. • All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • There are No piping holes in this product range • Step hole positions are located approx.150mm from top & bottom (D,E) at intervals of 300mm (F) • STEPS ARE BOLT - ON type • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1350mm or 1220mm dia and Separate Base size suitable are 1240mm & 1450mm

diameter. • Please contact your local council for the sizing requirements for your area.







36 | P a g e



CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg)

A B E10B 900 X 1200 (pictured) 763 530 E11B 900 X 900 572 400 E12B 900 X 600 381 260

• All Liners have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Liners have 2 x 1.3T Lifting Anchors. • There are No piping holes in this product range • Step hole positions are located approx.150mm from top & bottom (D,E) at intervals of 300mm (F) • STEPS ARE BOLT - ON type • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1000mm dia and Separate Base sizes suitable is 1150mm diameter. • Please contact your local council for the sizing requirements for your area.







37 | P a g e

SPACER RINGS

FOR 1200 Ø LINERS

CODE SIZES # LIFTING POINTS (1.3 TONNE)

(each)

WEIGHT

(kg) A B C E07C 1350mm Dia x 150mm Thick with 900mm Dia Hole 2

FOR 1050 Ø LINERS

CODE SIZES #LIFTING POINTS (1.3 TONNE)

(each)

WEIGHT

(kg) A B C E09D 1260mm Dia x 150mm Thick with 980mm Dia Hole 2 E09E 1260mm Dia x 100mm Thick with 980mm Dia Hole 2

FOR 900 Ø LINERS


CODE SIZES # LIFTING POINTS (1.3 TONNE)

(each)

WEIGHT

(kg) A B C E12D 1000mm Dia x 150mm Thick with 750mm Dia Hole 2 E12E 1000mm Dia x 100mm Thick with 750mm Dia Hole 2






38 | P a g e

PIPES- WITH RUBBER RING JOIN

CODE

INTERNAL DIAMETER

BARREL

(mm)

A

EXTERNAL DIAMETER

BARREL

(mm)

B

OVERALL LENGTH

(mtr)

C

EFFECTVE LENGTH

(mtr)

D

WALL

THICKNESS

(mm)

CLASS

WEIGHT

(kg)

P01 300 510 2.44 2.34 45 4 312 P02 375 585 2.44 2.34 45 4 368 P03 450 670 2.44 2.34 48 4 465 P04 600 840 2.44 2.34 55 4 690 P05 750 1020 2.44 2.34 68 4 1050 P06 900 1240 2.44 2.34 85 4 1640 P07 1200 1570 2.44 2.34 100 4 2500

*Pipes are manufactured in accordance with requirements of AS-NZS 4058-2007 standards ***Weights & Measurements are a guide only. Some variations will occur






39 | P a g e

PIPE HEADWALLS


CODE

PIPE SIZE

(mm)

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

F (mm)

G (mm)

H (mm)

#LIFTING

ANCHORS (each)

WEIGHT

(kg)

PH01 300 DIA 600 250 430 430 600 725 1500 90 2 400 PH02 375 DIA 750 350 570 475 600 880 1650 90 2 PH03 450 DIA 750 250 570 565 600 880 1650 90 2 PH04 600 DIA 980 300 900 720 600 1100 1760 90 3 PH05 750 DIA 980 150 900 890 600 1100 1760 90 3 PH06 900 DIA 1550 550 930 1065 1200 1540 3000 120 4 PH07 1200 DIA 1550 550 930 1420 1200 1540 3000 120 4






40 | P a g e

RETAINING WALL (L SHAPE)

CODE

DESCRIPTION

HEIGHT LENGTH

(mm) mm)

WIDTH

(mm)

WALL

THICKNESS (mm)

#LIFTING POINTS (each)

WEIGHT

(kg)

A B C D L0 2000 L SHAPED RETAINING WALL 2000 2000 1050 5 2100 L01 1800 L SHAPED RETAINING WALL 1800 2000 1050 130 150 5 1900 L02 1500 L SHAPED RETAINING WALL 1500 2000 1050 130 150 5 1700 L03 1200 L SHAPED RETAINING WALL 1200 2000 940 100 140-150 5 1500

We custom make to order. Corners can also be made if required. ***Weights & Measurements are a guide only. Some variations will occur






41 | P a g e

SEPTIC TANKS

Septic Tank Septic tank-with base cast in INDIVIDUAL

CODE

SIZES


WALL

THICKNESS

(mm)

100mm Ø 100mm Ø INLET OUTLET HEIGHT HEIGHT From Bottom From Bottom (mm) (mm)

CAPACITY

(ltrs)

WEIGHT

(kg)

A B C D E A05 1800 X 1800 90 1510 1460 3335 2400 A05A 1800 X 1875 w/base cast in 90 1575 1460 3335 3600 A06 1800 X 1500 90 1210 1160 2571 2000 A06A 1800 X 1575 w/base cast in 90 1275 1160 2571 3100 A04A 1500 X 1500 75 1210 1160 1970 1400 A04AA 1500 X 1530 w/base cast in 75 1240 1160 1970 1840 A04B 1200 X 1500 75 1160 1160 1269 1100 A04BB 1200 X 1500 w/base cast in 75 1190 1160 1269 1400

• Our Septic tanks are approved to Australian Standard AS/NZS 1546. • We comply with Department of Health, under the Code of Practice for Product Approval of Onsite Wastewater

Systems. • Approval # F-AA-31116 • Further information can be found through www.public.health.wa.gov.au




http://www.public.health.wa.gov.au/




42 | P a g e

SEPTIC TANKS - CONT.

SETS

CODE

DESCRIPTION

TOTAL WEIGHT

(KG)

A00

1500 & 1200 (BOTH TANKS) W/STANDARD COVERS (2PCE)

3120

A00A

1500 & 1200 (BOTH TANKS) W/STANDARD COVERS (2PCE) & W/ BASES CAST IN

3860

A0

1500 & 1200 (BOTH TANKS) W/TRAFFIC COVERS (2PCE)

3875

A00B

1500 & 1200 (BOTH TANKS) W/TRAFFIC COVERS (2PCE) & W/ BASES CAST IN

4615

A02

1200 Ø x 1500 (SINGLE TANK ONLY) W/ STANDARD COVER

1330

A04

1200 Ø x 1500 (SINGLE TANK ONLY) W/ TRAFFIC COVER

1645

A01

1500 Ø x 1500 (SINGLE TANK ONLY) W/ STANDARD COVER

1790

A03

1500 Ø x 1500 (SINGLE TANK ONLY) W/ TRAFFIC COVER

2230

• Our Septic tanks are approved to Australian Standard AS/NZS 1546. • We comply with Department of Health, under the Code of Practice for Product Approval of Onsite Wastewater

Systems. • Approval # F-AA-31116 • Further information can be found through www.public.health.wa.gov.au




http://www.public.health.wa.gov.au/




43 | P a g e

LEACH DRAINS, ENDS & COVERS LEACH DRAINS- STANDARD & TRAFFIC

CODE DESCRIPTION WIDTH

OVERALL INTERNAL (mm) (mm)

HEIGHT OVERALL

(mm)

WALL THICKNESS

(mm)

TOP (mm)

LENGTH

(mm)

LIFTING POINTS

(#)

WEIGHT

(kg) A B C D E F G17 LEACH DRAIN- STD (NON TRAFFIC 850 630 685 65 65 1200 1 500 G18 LEACH DRAIN - TRAFFIC 850 630 770 65 150 1200 1 630

** Only 2 x 1.2 Mtr Modular Sections with Inspection Caps will be supplied for every leach drain. 1.LEACH DRAIN ENDS 2.LEACH DRAIN COVER

CODE

DESCRIPTION

DIAGRAM

WIDTH HEIGHT

(mm) (mm)

THICKNESS

(mm)

HOLE

(mm)

HOLE LOCATION

FROM TOP (mm)

#LIFTING POINTS

#

WEIGHT

(kg)

A B C D E G19 LEACH DRAIN ENDS (each) 1 780 680 65 120 90 1 50 G01 LEACH DRAIN COVER 2 840 600 55 n/a n/a 1 60

*** Weights & Measurements are a guide only. Some variations will occur






44 | P a g e

SOAKWELLS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B

F **1800 X 1800 4580 2400 F00B 1800 X 1500 3816 2000 F0 1800 X 1200 3050 1530 F00A 1800 X 900 2290 1140 F00 1800 X 600 1525 750

• All Soakwells have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Soakwells have 2 x Lifting/Piping Holes approx.100mm diameter, located approx. 220mm from

top of tank (C) • ** 1800 X 1800 Soakwells have 2 x 200mm dia Knock outs, located 1300mm from bottom • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid and Base size suitable are 2000mm diameter. • Please contact your local council for the sizing requirements for your area.







45 | P a g e

SOAKWELLS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B F01 1500 X 1500 2650 1400 F02 1500 X 1200 2120 1100 F03 1500 X 900 1590 800 F04 1500 X 600 1060 520

• All Soakwells have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Soakwells have 2 x Lifting/Piping Holes approx.100mm diameter, located approx. 180mm from

top of tank (C) • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1650mm and Base size suitable is 1700mm diameter • Please contact your local council for the sizing requirements for your area.







46 | P a g e

SOAKWELLS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B F05 1200 X 1500 1697 1100 F06 1200 X 1200 1357 880 F06A 1200 X 900 1018 650 F07 1200 X 600 678 430

• All Soakwells have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Soakwells have 2 x Lifting/Piping Holes approx.100mm diameter, located approx. 110-180mm

from top of tank (C) • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1350mm and Base size suitable is 1450mm diameter • Please contact your local council for the sizing requirements for your area.







47 | P a g e

SOAKWELLS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B F10 900 X 1200 763 530 F11 900 X 900 572 400 F12 900 X 600 381 260

• All Soakwells have an Interlocking spigot of approximately 30mm which is in addition to depth. • All Soakwells have 2 x Lifting/Piping Holes approx.100mm diameter, located approx. 110-180mm

from top of tank (C) • Manufactured with 40mpa concrete and Reinforced 5mm wire cage • Lid size suitable is 1000mm and Base size suitable is 1150mm diameter • Please contact your local council for the sizing requirements for your area.







48 | P a g e

SOAKWELLS


CODE

SIZES


CAPACITY

FULL HEIGHT

(ltrs)

WEIGHT

(kg) A B F14 600 X 900 254 270 F15 600 X 600 169 180

• All Soakwells have an Interlocking spigot of approximately 30mm which is in addition to depth. • This size does not have lifting holes. • Manufactured with 40mpa concrete. • Reinforced 5mm wire cage only in the 600 x 900. 600 x 600 is not reinforced. • Lid size/s suitable are 700mm or 760mm and Base size suitable is 760mm diameter • Please contact your local council for the sizing requirements for your area.







49 | P a g e

VARIOUS PRODUCTS

BOLT ON STEP IRON






50 | P a g e

CAST IRON ROUND COVER & FRAMES ONLY (CLASS D, 8 TONNE WHEEL LOAD RATING)

CODE OVERALL SIZE Ø AT TOP AT BOTTOM (mm) (mm)

FRAME HEIGHT

(mm)

CLEAR OPENING SIZE Ø

(mm)

COVER SIZE

(mm) (mm)

WEIGHT

(kg)

Z06 672 780 75 604 dia 648 x 60 70 Z06A 672 780 125 604 dia 648 x 60 75 Z06AA 672 780 200 604 dia 648 x 60 95







51 | P a g e

GALVANISED STEEL SQUARE GRATES & FRAMES ONLY (HINGED & BOLT DOWN) CLASS C, 5 TONNE WHEEL LOADING

CODE

OVERALL SIZE

(mm)

FRAME HEIGHT

(mm)

CLEAR OPENING SIZE

WIDTH X LENGTH (mm) (mm)

GRATE SIZE


WEIGHT

(kg) Z03 550 SQUARE (CLASS C) 55 535 x 435 515 x 504 29 Z02A 550 SQUARE (CLASS C) 150 535 x 435 515 x 504 37 Z02 550 SQUARE (CLASS C) 250 535 x 435 515 x 504 48 Z04 450 SQUARE (CLASS C) 45 445 x 355 425 x 404 17 Z04AA 450 SQUARE (CLASS C) 250 445 x 355 425 x 404 33 Z05 350 SQUARE (CLASS C) 40 325 x 265 305 x 304 9







52 | P a g e

GALVANISED STEEL HEELPROOF GRATES & FRAMES ONLY (HINGED & BOLT DOWN) CLASS D, 8 TONNE WHEEL LOADING

CODE

OVERALL SIZE


FRAME HEIGHT

(mm)

CLEAR OPENING SIZE


GRATE SIZE


WEIGHT

(kg)

Z10A 712 X 712 131 600 X 600 694 X 694 104







53 | P a g e

GALVANISED STEEL RECTANGLE GRATES & FRAMES ONLY (HINGED & BOLT DOWN) CLASS D, 8 TONNE WHEEL LOADING

CODE

OVERALL SIZE


FRAME HEIGHT

(mm)

CLEAR OPENING SIZE


GRATE SIZE


WEIGHT

(kg)

Z01AA 760 X 545 75 750 X 445 730 X 505 53 Z01A 760 X 545 150 750 X 445 730 X 505 58 Z01AB 760 X 545 250 750 X 445 730 X 505 70 Z01B 760 X 545 BUBBLE UP 225 750 X 445 730 X 505 62







54 | P a g e

GALVANISED STEEL CHANNEL DRAIN GRATE ONLY

CODE

DESCRIPTION

LENGTH

(mm)

WIDTH (mm)

HEIGHT

(mm)

BARS (mm)

WEIGHT

(kg)

H02 CHANNEL DRAIN GRATE – MEDIUM DUTY CLASS C- 5 TONNE WHEEL LOADING

995

215

32

32 X 5 (FLAT BAR)

13

H03

CHANNEL DRAIN GRATE – HEAVY DUTY CLASS D- 8 TONNE WHEEL LOADING

995

215

32

32 X 8 (FLAT BAR)

20







55 | P a g e

CAST IRON ROUND GRATES & FRAMES ONLY (CLASS D, 8 TONNE WHEEL LOAD RATING)

CODE OVERALL SIZE Ø AT TOP AT BOTTOM (mm) (mm)

FRAME HEIGHT

(mm)

CLEAR OPENING SIZE Ø

(mm)

GRATE SIZE

DIA X DEPTH (mm) (mm)

WEIGHT

(kg)

Z07 672 780 75 604 dia 648 x 60 68 Z07A 672 780 125 604 dia 648 x 60 76 Z07AA 672 780 200 604 dia 648 x 60 95 ***Weights & Measurements are a guide only. Some variations will occur






56 | P a g e

CAST IRON WAVE GRATES & FRAMES ONLY (CLASS D, 8 TONNE WHEEL LOAD RATING

CODE OVERALL SIZE WIDTH X LENGTH

(mm) (mm)

FRAME HEIGHT

(mm)

CLEAR OPENING SIZE WIDTH X LENGTH

(mm) (mm)

WEIGHT

(kg) Z10B 780 X 580 65 650 X 450 40 Z10C 780 X 580 130 650 X 450 46







57 | P a g e

CHANNEL DRAINS

CODE

DESCRIPTION

A

(Metre)

B

(mm)

C

(mm)

D

(mm)

E

(mm)

F

(mm)

G

(mm)

H

(mm)

I

(mm)

J

(mm)

LIFTING LUGS #

(each)

WEIGHT

(kg)

H01

CHANNEL DRAIN

1

415

270

350

130

160

160

155

30

220

2

135

** Segments with 100 mm Waste pipe hole (located at 1 end) are given upon request







58 | P a g e

CHANNEL DRAIN – END CAP

CODE

DESCRIPTION

A

(mm)

B

(mm)

C

(mm)

D

(mm)

E

(mm)

F

(mm)

G

(mm)

H

(mm)

WEIGHT

(kg) H01

CHANNEL DRAIN END

370

280

410

30

140

140

130

30

10







59 | P a g e

WHEEL STOPS

CODE

DESCRIPTION

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

F (mm)

G (mm)

# BOLT HOLES

20MM

LIFTING LUGS #

(each)

WEIGHT

(kg)

H05

WHEEL STOPS

1640

165

105

1580

105

30

300

2

2

60

*Bolts are sold separately.







60 | P a g e

BOX CULVERTS

CODE

DESCRIPTION

LENGTH

A (mm)

WIDTH

B (mm)

HEIGHT

C (mm)

WALL THICKNESS

D E F (mm) (mm) (mm)

INTERNAL

G H I (mm) (mm) (mm)

LIFTING LUGS #

(each)

WEIGHT

(kg)

RCB1

BOX CULVERT – 1200

2000

1200

1200

130 150 160

1740 1700 150

2

RCB1

BOX CULVERT - 600

2000

1200

600

130 150 160

1740 1700

2

PLEASE NOTE: These items are not rated for Main Roads projects.

F

E

A

D

B

C

H

G

I



Documents

BASES FOR SOAKWELLS & LINERS - Maddington Concrete · 2019-11-07 · MADDINGTON CONCRETE PRODUCTS Pty Ltd Maddington Concrete Products Pty Ltd 66 Kelvin Road Maddington, WA 6109 Ph