DQD 507 Rev. 2012-05-22 Page 1

Certificate of Compliance Certificate: 70034640 (170351) Master Contract: 170351

Project: 70034640 Date Issued: 2015-06-01

Issued to: Bel Fuse Inc. 206 Van Vorst St Jersey City, New Jersey 07302 USA Attention: Editha S. Vergara

The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent

indicator 'US' for US only or without either indicator for Canada only.

Issued by:

Juan-Carlos Olivera Juan-Carlos Olivera, MSc.

PRODUCTS CLASS – 5311 11 - POWER SUPPLIES - Component Type (CSA 60950-1-07-2nd Ed) CLASS – 5311 91 - POWER SUPPLIES - Component Type (UL 60950-1-2nd Ed) Certified to U.S. Stds For details related to rating, size, configuration, etc. reference should be made to the CSA Certification Record or the descriptive report. Component type power supplies intended for use with Information Technology and Business Equipment, where the suitability of the combination is to be determined by CSA Group. AC/DC Switching Power Supply, Models SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43, and SPACSCO-44; Input: 100-240 V ac, 12-5 A, 50-60 Hz; Output: V1: 12 V dc/90 A (*), V2: 3.3 V dc/3 A; Classification Level 6. Model PET1300-12-054NA; Input: 100-240 V ac, 12-6 A, 50-60 Hz; Output: V1: 12 V dc/108 A (**), V2: 3.3 V dc/3 A; Classification Level 6. Notes: 1. For models SPACSCO-26, SPACSO-34 and SPACSCO-39 only: * V1 output current: max 90 A at 100-

240 V ac input, 45°C operating ambient and at 120-240 V ac input, 55°C operating ambient; derated to max 80 A at 100-120 V ac input, 55°C operating ambient.

Certificate: 70034640 Project: 70034640

Master Contract: 170351 Date Issued: 2015-06-01

DQD 507 Rev. 2012-05-22 Page 2

2. For model PET1300-12-054NA only: ** V1 output current: derated to max 90 A at 90-108 V ac input, 45°C operating ambient and 63 A at 60°C operating ambient. V1 is maximum 108 A at 108V-264 Vac, 45°C operating ambient and 76.3 A at 60°C operating ambient.

3. Model designations may be followed by suffix G denoting non-safety critical options. APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No 60950-1-07, +Am.1:2011 +Am.2:2014

− Information Technology Equipment - Safety - Part 1: General Requirements

UL 60950-1-2014 − Information Technology Equipment - Safety - Part 1: General Requirements

CONDITIONS OF ACCEPTABILITY 1. Equipment shall be installed only by trained service personnel, according to the manufacturer installation

instructions.

2. Evaluated for use in a Pollution Degree 2 environment.

3. Temperature tests shall be considered for specific installation conditions in the end system.

4. Evaluated as Class I (earthed equipment). Reliable connection to Protective Earth shall be provided in the end use installation.

5. Evaluated for connection to AC power with a branch circuit protector rated max 20 A.

6. The appliance inlet for the detachable power supply cord is considered the main disconnect device.

7. Spacings were evaluated for an operating altitude of max 4000 m, based on IEC-60664-1 altitude

correction factors.

8. Suitability of the enclosure provided with the equipment as a FIRE, MECHANICAL and ELECTRICAL enclosure is to be determined in the end system. Front bezel was evaluated and complies with electrical and mechanical requirements.

9. The Output circuits are SELV; Output V1 operates at hazardous energy levels (> 240 VA).

10. The Output connector is not suitable for field wiring; it is only intended for connection to the mating connectors in the end system. The connector was evaluated and may be used for hot swap operation. Current Interruptions Test (100 cycles for all models except PET1300, 200 cycles for PET1300) was performed.

DQD 507 Rev. 2012-05-22 Page 1

Supplement to Certificate of Compliance

Certificate: 70034640 (170351) Master Contract: 170351

The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate.

Product Certification History Project Date Description

70034640 2015-06-01 AC-DC Switching Power Supply, Models SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44 and PET1300-12-054NA. (C/US) (transferred from 173688 - 2385539 and upgraded to include Am2).

CERTIFICATENo. P15219352

Order No. 278236 Page 1/2

Date of issue 03-02-2015

Juan Z. KleppenesCertification Department

Nemko ASGaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, NorwayTEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL info@nemko.comENTERPRISE NUMBER NO974404532 nemko.com

Product AC/DC Switching Power Supply

Applicant Bel Fuse Inc.206 Van Vorst St.Jersey City, NJ 07302USA

Manufacturer Bel Fuse Inc.206 Van Vorst St.Jersey City, NJ 07302USA

Factory See page 2

Ratings 100–240 V, 12-5 A, 50-60 Hz ( Models SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44) 100–240 V, 12-6 A, 50-60 Hz ( Model PET1300-12-054NA)

Trade mark

Model / Type Ref. SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43,SPACSCO-44, PET1300-12-054NA

Principal characteristics model name may be followed by G indicating RoHS version. See test report forDC Output Ratings

See next page(s)

A sample of the product was testedand found to be in conformity with

OFF EN 60950-1:2006;A11;A1;A12;A2

Validity This certificate documents conformity with the standards shown, and also applies as license foruse of Nemkos name and certification mark. The certificate and license is valid as long as theapplicable conditions are complied with, and provided that any changes to the product are notifiedto Nemko for acceptance prior to implementation.New standards or amendments to the standards may imply that the product design must beupdated and/or that re-testing and re-certification is necessary.

Additional information See next page(s)

The abovementioned certified equipment complies with current regulatory requirements regardingelectrical safety in Norway and other EU/EEA member states, as far as this can be checked.Compliance with requirements regarding building-in, protection against electric shock andElectromagnetic Compatibility (EMC) must be checked when the equipment is built-in a completedproduct or forms a part of a complete system.

Additional model(s) See next page(s)

CERTIFICATENo. P15219352

Order No. 278236 Page 2/2

Date of issue 03-02-2015

Juan Z. KleppenesCertification Department

Nemko ASGaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, NorwayTEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL info@nemko.comENTERPRISE NUMBER NO974404532 nemko.com

Factories:

BPS Asia Pacific Electronics (Shenzhen) Co., Ltd.Building# 6, Nanming Road, Gongming Town HuahongXintong Industrial Park, Guangming DistrictShenzhen 518108China

Bel Power Solutions, s.r.o.ArealZTS Dubnica n.Vahom c.924Dubnica nad Vahom 01841Slovakia

Ref. Certif. No.

NO84858

Gaustadalléen 30NO-0373 Oslo, Norway

Date: 03-02-2015 Signature: Juan Z. KleppenesCertification Department

Issued 2007-04 1/2

IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICALEQUIPMENT (IECEE) CB SCHEME

SYSTEME CEI DACCEPTATION MUTUELLE DE CERTIFICATS DESSAIS DESEQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC

CB TEST CERTIFICATE CERTIFICAT D'ESSAI OC

ProductProduit AC/DC Switching Power Supply

Name and address of the applicantNom et adresse du demandeur

Bel Fuse Inc.206 Van Vorst St.Jersey City, NJ 07302USA

Name and address of the manufacturerNom et adresse du fabricant

Bel Fuse Inc.206 Van Vorst St.Jersey City, NJ 07302USA

Name and address of the factoryNom et adresse de l'usineNote: When more than one factory, please report on page 2Note: Lorsque il y plus d'une usine, veuillez utiliser la deuxième page

Additional information on page 2

Ratings and principal characteristicsValeurs nominales et caractéristiques principales

100–240V 12-5 A 50-60 Hz ( Models SPACSCO-26, SPACSCO-34,SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44) 100–240V12-6 A 50-60 Hz ( Model PET1300-12-054NA)

Trademark (if any)Marque de fabrique (si elle existe)

Type of Manufacturer’s Testing Laboratories usedType de programme du laboratoire d’essais constructeur

WMT

Model / Type Ref.Ref. De type

SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41,SPACSCO-43, SPACSCO-44, PET1300-12-054NA

Additional information (if necessary may also bereported on page 2)Les informations complémentaires (si nécessaire,peuvent être indiqués sur la deuxième page

model name may be followed by G indicating RoHS version. See testreport for DC Output Ratings

Additional information on page 2

A sample of the product was tested and foundto be in conformity withUn échantillon de ce produit a été essayé et a étéconsidéré conforme à la

IEC 60950-1(ed.2);am1;am2

As shown in the Test Report Ref. No. which forms partof this CertificateComme indiqué dans le Rapport dessais numéro deréférence qui constitue partie de ce Certificat

278236

This CB Test Certificate is issued by the National Certification BodyCe Certificat dessai OC est établi par l'Organisme National de Certification

Ref. Certif. No.

NO84858

Gaustadalléen 30NO-0373 Oslo, Norway

Date: 03-02-2015 Signature: Juan Z. KleppenesCertification Department

Issued 2007-04 2/2

BPS Asia Pacific Electronics (Shenzhen) Co., Ltd.Building# 6, Nanming Road, Gongming Town HuahongXintong Industrial Park, Guangming DistrictShenzhen 518108China

Bel Power Solutions, s.r.o.ArealZTS Dubnica n.Vahom c.924Dubnica nad Vahom 01841Slovakia

Test Report issued under the responsibility of

www.nemko.com

This Test Report, when bearing the Nemko name and logo is only valid when issued by a Nemko laboratory, or by a laboratory having special agreement with Nemko.

TEST REPORT

IEC 60950-1 Information technology equipment – Safety –

Part 1: General requirements

Report Number. ...............................: 278236

Date of issue .....................................: 30 January 2015

Total number of pages ......................: 75

Applicant’s name ............................: Bel Fuse Inc.

Address .............................................: 206 Van Vorst St., Jersey City, NJ 07302

Test specification:

Standard ...........................................: IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013

Test procedure..................................: CB-Scheme

Non-standard test method ................: N/A

Test Report Form No. .................... : IEC60950_1F

Test Report Form(s) Originator ........: SGS Fimko Ltd

Master TRF .......................................: Dated 2014-02

Copyright © 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System). All rights reserved.

This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

General disclaimer:

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report.

Page 2 of 75 Report No 278236

TRF No. IEC60950_1F

Test item description .................... : AC-DC switching power supply

Trade Mark .......................................:

Manufacturer .....................................: Same as Applicant

Model/Type reference .......................: SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44, PET1300-12-054NA (maybe follow by G indicating RoHS version)

Ratings ..............................................: 100–240 V, 12-5 A, 50-60 Hz ( Models SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44)

100–240 V, 12-6 A, 50-60 Hz ( Model PET1300-12-054NA)

See General Product Information for Output Ratings.

Testing procedure and testing location:

CB Testing Laboratory: Nemko USA, Inc.

Testing location/ address ............................ : 2210 Faraday Avenue, Carlsbad CA, 92008, USA

Testing procedure: WMT BPS Asia Pacific Electronics (Shenzhen) Co., Ltd.

Testing location/ address ............................ : Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District 518108 Shenzhen PEOPLE'S REPUBLIC OF CHINA

Tested by (name + signature) ...................... : Editha Vergara

Witnessed by (name + signature) .............. : Luis Gonzalez

Approved by (name + signature) ................ : Jeff Busch

Report History:

Original report.

List of Attachments: (including a total number of pages in each attachment)

Attachment 1: European Group Differences and National Deviations ........................................... 84 pages

Attachment 2: Miscellaneous Documentation, e.g. Photos, PWB Layout, Schematic etc. .......... 45 pages (Not for publication – Engineering use only)

Page 3 of 75 Report No 278236

TRF No. IEC60950_1F

Summary of testing

General All comments relate to all models, unless specifically stated.

Power supply The equipment is an enclosed, Class I switch mode power supply with universal AC input and multiple DC voltage outputs for building-in. This report covers multiple models and all comments / tests apply to all models unless otherwise indicated.

1.1.2; The unit is intended to operate at an altitude over 2000 m.

This equipment is intended to be operated at an altitude of up to 4000 m (SPACSCO-26, SPACSCO-34, SPACSCO-39), so the clearance is multiplied by the altitude correction factor (1.29), 3050 m (SPACSCO-41, SPACSCO-43, SPACSCO-44, PET1300-12-54NA) , clearance is multiplied by the altitude correction factor (1.15) specified in table A.2 of IEC 60664-1 2nd Edition:2007-04. Refer to Tables 2.10.3 and 2.10.4.

1.5, 3.2.5; Power supply cord set. A power supply cord set is not provided with the power supply. A power supply cord set, complying with the national regulations of the country in which the product is to be sold, shall be provided with the end-use equipment.

1.7.2; Safety instructions. Instructions and equipment markings related to safety are to be provided in a language, which is acceptable in the country in which the equipment is to be sold. English language verified.

5.2: Electric Strength test Increased test voltages for Basic insulation applied to the equipment, based on measured working voltages.

Page 4 of 75 Report No 278236

TRF No. IEC60950_1F

Summary of testing:

Tests performed (name of test and test clause):

1) Input Test ( Clause 1.6.2)

2) Durability Test ( Clause 1.17.11)

3) Capacitance Discharge Test ( Clause 2.1.1.7)

4) SELV Reliability Test (Clause 2.2 )

5) Protective Bonding Test (Clause 2.6.3.4)

6) Humidity Test (Clause 2.9.2)

7) Working Voltage Measurement (Clause 2.10.2)

8) Hazardous Voltage Measurement (Clause 2.10.2)

9) PCB Thermal Ageing Test (Clause 2.10.9) *

10) Mechanical and Stress Relief test (Clause 4.2)

11) Connector Interruption test (Clause 4.3.5)

12) Heating Test (Clause 4.5.1)

13) Touch Current Test (Clause 5.1)

14) Electric Strength Test (Clause 5.2.2)

15) Component Failure Test (Clause 5.3)

16) Abnormal Operation Test (Clause 5.3)

17) PS Output Overload and Short Test (Clause 5.3)

Testing location:

(Original testing conducted at the following location; facility closure) Power-One Inc. 740 Calle Plano Camarillo, CA 93012

(New location) BPS Asia Pacific Electronics (Shenzhen) Co., Ltd. Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District 518108 Shenzhen PEOPLE'S REPUBLIC OF CHINA

* Thermal Ageing test was performed at CSA International, 13799 Commerce, Pkwy, Richmond, BC Canada V6V 2N9.

Summary of compliance with National Differences

List of countries addressed:

Austria (AT), Australia (AU), Canada (CA), China (CH), Denmark (DK), Finland (FI), Germany (DE), Ireland (IE), Israel (IS), Korea (KR), Norway (NO), Slovenia (SI), Spain (ES), Sweden (SE), Switzerland (CH), United Kingdom (GB), United States of America (US)

The product fulfils the requirements of : EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013

Page 5 of 75 Report No 278236

TRF No. IEC60950_1F

Copy of marking plate: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks.

Page 6 of 75 Report No 278236

TRF No. IEC60950_1F

Calibration All instruments used in the tests given in this test report are calibrated and

traceable to national or international standards. Further information about traceability will be given on request.

Measurement uncertainty

Measurement uncertainties are calculated for all instruments and instrument set-ups given in this report. Calculations are based on the principles given in the standard EA-4/02 (Dec. 1999), IEC Guide 115:2007, Nemko routine L227 and other relevant internal Nemko-procedures. Further information about measurement uncertainties will be given on request.

Evaluation of results If not explicitly stated otherwise in the standard, the test is passed if the measured value is equal to or below (above) the limit line, regardless of the measurement uncertainty. If the measured value is above (below) the limit line, the test is not passed - ref IEC Guide 115:2007, and Nemko routine L220. The instrumentation accuracy is within limits agreed by IECEE-CTL (ref. Nemko routine L227).

Page 7 of 75 Report No 278236

TRF No. IEC60950_1F

Test item particulars:

Equipment mobility....................................................... : [] movable [] hand-held [] transportable [] stationary [ X ] for building-in [] direct plug-in

Connection to the mains .............................................. : [ X ] pluggable equipment [ X ] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [] not directly connected to the mains

Operating condition ...................................................... : [ X ] continuous [] rated operating / resting time:

Access location ........................................................... : [ X ] operator accessible [] restricted access location

Over voltage category (OVC) ..................................... : [] OVC I [ X ] OVC II [] OVC III [] OVC IV [] other:

Mains supply tolerance (%) or absolute mains supply values ........................................................................... : -10%, +10%

Tested for IT power systems ...................................... : [] Yes [ X ] No

IT testing, phase-phase voltage (V) .......................... : —

Class of equipment ..................................................... : [ X ] Class I [] Class II [] Class III [] Not classified

Considered current rating of protective device as part of the building installation (A) ..................................... :

16 A for Europe, 20 A for North America

Pollution degree (PD) ................................................. : [] PD 1 [ X ] PD 2 [] PD 3

IP protection class ...................................................... : IP20

Altitude during operation (m) ...................................... : 4000 m (SPACSCO-26, SPACSCO-34, SPACSCO-39)

3050 m (SPACSCO-41, SPACSCO-43, SPACSCO-44, PET1300-12-54NA)

Altitude of test laboratory (m) ..................................... : 38 m

Mass of equipment (kg) .............................................. : 1.09 kg

Temperature, Ambient .............................................. : 45 °C, see general product information area for more details.

Possible test case verdicts:

- test case does not apply to the test object ................ : N/A

- test object does meet the requirement ...................... : P (Pass)

- test object does not meet the requirement ................ : F (Fail)

Page 8 of 75 Report No 278236

TRF No. IEC60950_1F

Testing:

Date of receipt of test item ............................................ : N/A – Testing performed at manufacturer’s location (WMT)

Date(s) of performance of tests .................................... : 2010-12-17 to 2010-12-22, 2011-03-01 to 2011-03-03, 2011-10-06 to 2011-10-10, 2013-01-08 to 2013-01-25, 2013-06-19 to 2013-06-20, 2014-04-07 to 2014-04-09

General remarks:

"(see appended table)" refers to a table appended to the report.

"(see Enclosure #)" refers to additional information appended to the report.

The test results presented in this report relate only to the object tested.

This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.

Throughout this report a comma / point is used as the decimal separator.

Manufacturer’s Declaration per sub-clause 4.2.5 of IECEE 02:

The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided :

Yes

Not applicable

When differences exist; they shall be identified in the General product information section.

Name and address of factory (ies) ...........................:

Bel Power Solutions, s.r.o. ArealZTS Dubnica n.Vahom c.924 01841 Dubnica nad Vahom SLOVAKIA

BPS Asia Pacific Electronics (Shenzhen) Co.,Ltd. Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District 518108 Shenzhen PEOPLE'S REPUBLIC OF CHINA

Page 9 of 75 Report No 278236

TRF No. IEC60950_1F

General product information:

Model SPACSCO-26, SPACSCO-34, SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44, and PFE1300-12-054NA are switching power supplies for building-in. The units have two DC outputs, 12 V main output, and 3.3 V.

The unit is provided with AC inlet, output connector, metal enclosure, plastic front panel, and fan. The fan is installed on the main board slot through the fan metal bracket. The unit consists of four boards, namely: Main, Control, Auxiliary, and Bulk capacitor boards. Control board is connected to the main board by connectors. The bulk capacitor board is soldered to the Main board. The auxiliary board is soldered on top of the bulk capacitor board and connected to the control board by two-pin connector.

MODEL DIFFERENCES:

SPACSCO-26 is base model.

SPACSCO-34 is exactly the same as model SPACSCO-26 except for reverse airflow (air from output to input).

SPACSCO-39 is exactly the same SPACSCO-26 except for the color of the front faceplate.

SPACSCO-41 is exactly the same as SPACSCO-26 except for higher efficiency, single fuse, different PFC choke, transformers due to different core, and some rating of other components.

SPACSCO-43 is exactly the same SPACSCO-41 except for the color of the front faceplate.

SPACSCO-44 is exactly the same as model SPACSCO-41 except for airflow direction. Model SPACSCO-41 airflow is from input to output while SPACSCO-44 is from output to input.

Model PET1300-12-054NA is exactly the same as SPACSCO-44G except for maximum output power at 120-240 Vac and change of L2 choke part number due to reduce of one turn for the winding.

ADDITIONAL ELECTRICAL RATING INFORMATION:

Input Output (DC) Model V A Hz V A

SPACSCO-26, 100-240 12-5 50-60 V1: 12 90 * SPACSCO-34, V2: 3.3 3 SPACSCO-39, SPACSCO-41, SPACSCO-43, SPACSCO-44

PET1300-12-054NA 100-240 12-6 50-60 V1: 12 108 **

V2: 3.3 3 *Note: For models SPACSCO-26, SPACSCO-34 and SPACSCO-39 only: 1) V1 maximum output current: 90 A at 100-240 Vac, 45°C operating ambient and at 120-240 V, 55°C ambient. 2) V1 maximum output current is de-rated to 80 A at 100-120V input voltage, 55°C operating ambient. **Note: For model PET1300-12-054NA only: 1) V1 output current: derated to max 90 A at 90-108 V ac input, 45°C operating ambient . V1 is maximum 108 A at 108V-264 Vac, 45°C operating ambient.

Page 10 of 75 Report No 278236

TRF No. IEC60950_1F

Conditions of Acceptability:

These models require:

1) The power supply is to be installed only by trained service personnel, according to manufacturer installation instructions.

2) Evaluated as Class I (earthed equipment). Reliable earth connection shall be provided in the end use installation.

3) Evaluated for use in a Pollution Degree 2 environment, up to 1800 m altitude, 55°C ambient and up to 4000 m, 45°C ambient for models SPACSCO-26, SPACSCO-34, and SPACSCO-39. Models SPACSCO-41, SPACSCO-43, SPACSCO-44, and PET1300-12-054NA can be operated up to 3050 m altitude, 55°C ambient.

4) Temperature tests shall be considered for specific installation conditions in the end system.

5) A suitable Electrical and Fire Enclosure shall be provided on rear side of the power supply. Front Bezel has been evaluated and meets requirements.

6) All secondary output circuits are SELV.

7) Secondary output, V1, is at Hazardous energy level; Secondary output, V2, is at Non-Hazardous energy level.

8) The output connector has not been evaluated for field wiring.

9) The Connector Current Interruption Test was performed on the Output Connector (FCI and Tyco) for 100 cycles (for all model except PET1300-12-054NA)/200 cycles (PET1300-12-054NA (insertion/withdrawal). Testing for additional cycles shall be determined during the end product evaluation, depending on end product application.

10) The equipment was tested on a listed 20 A branch circuit. If used on a branch circuit greater than this, additional testing may be necessary.

Abbreviations used in the report:

- normal conditions ....................................... N.C. - single fault conditions ........................ S.F.C - functional insulation ..................................... OP - basic insulation ........................................ BI - double insulation ............................................ DI - supplementary insulation ......................... SI - between parts of opposite polarity ............. BOP - reinforced insulation ................................ RI

Indicate used abbreviations (if any): .......... None