CGC 400 parameter list 4189340789 UK_2013.12.13

DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: +45 9614 9614 Fax: +45 9614 9615 [email protected] www.deif.com



PARAMETER LIST

Compact Genset Controller, CGC 400 Alarm list Parameter list

Document no.: 4189340789ASW version:

1. General information1.1. Warnings, legal information and safety..................................................................................................4

1.1.1. Warnings and notes ......................................................................................................................41.1.2. Legal information and disclaimer ..................................................................................................41.1.3. Safety issues ................................................................................................................................41.1.4. Electrostatic discharge awareness ...............................................................................................41.1.5. Factory settings ............................................................................................................................5

1.2. About the Parameter List........................................................................................................................51.2.1. General purpose of the Parameter List..........................................................................................51.2.2. Intended users...............................................................................................................................51.2.3. Contents and overall structure ......................................................................................................5

2. Alarm list2.1. General information about the alarm list................................................................................................6

2.1.1. Alarm list features and options .....................................................................................................62.2. Protection parameters............................................................................................................................8

2.2.1. Reverse power and overcurrent protection....................................................................................82.2.2. Voltage protections......................................................................................................................122.2.3. Frequency protections.................................................................................................................142.2.4. Busbar voltage protections..........................................................................................................172.2.5. Busbar frequency protections......................................................................................................192.2.6. Overload protections....................................................................................................................212.2.7. Undervoltage and reactive power low..........................................................................................23

2.3. Breaker control parameters..................................................................................................................252.3.1. Breaker alarms............................................................................................................................25

2.4. Input/output parameters, binary input setup.........................................................................................282.4.1. Digital input 10-15 and 56-57 setup.............................................................................................282.4.2. Digital input 6-8 setup..................................................................................................................292.4.3. Emergency stop...........................................................................................................................302.4.4. M-Logic alarm 1-5 setup .............................................................................................................31

2.5. Analogue input setup............................................................................................................................322.5.1. Multi-input no. 6...........................................................................................................................322.5.2. Multi-input no. 7 ..........................................................................................................................372.5.3. Multi-input no. 8...........................................................................................................................422.5.4. Speed and running feedback setup.............................................................................................472.5.5. Differential measurement.............................................................................................................502.5.6. Aux. supply setup........................................................................................................................532.5.7. Multi-input no. 58.........................................................................................................................542.5.8. Multi-input no. 59.........................................................................................................................59

2.6. System parameters, general setup......................................................................................................642.6.1. Engine heater failure....................................................................................................................642.6.2. Max. ventilation............................................................................................................................652.6.3. Switchboard error - Block and Stop.............................................................................................662.6.4. Switchboard error - Not in auto....................................................................................................672.6.5. Avg U BB.....................................................................................................................................68

2.7. System parameters, communication....................................................................................................692.7.1. External communication error......................................................................................................692.7.2. Engine interface communication alarms......................................................................................70

3. Parameter list3.1. General information about the parameter list.......................................................................................74

3.1.1. Parameter list settings.................................................................................................................743.2. Control parameter, regulation...............................................................................................................75

3.2.1. Regulation....................................................................................................................................753.3. Control parameters, output setup.........................................................................................................76

3.3.1. Digital output setup......................................................................................................................763.4. System parameters..............................................................................................................................773.5. System parameters, general setup......................................................................................................78

CGC 400 parameter list 4189340789 UK

DEIF A/S Page 2 of 98

3.5.1. General setup..............................................................................................................................783.5.2. Counters and timers....................................................................................................................813.5.3. Alarm horn...................................................................................................................................823.5.4. Run coil setup..............................................................................................................................823.5.5. Running, start and stop................................................................................................................833.5.6. Breaker control............................................................................................................................853.5.7. Idle start.......................................................................................................................................853.5.8. Engine heater..............................................................................................................................863.5.9. Cooling ventilation.......................................................................................................................863.5.10. Summer/winter time...................................................................................................................863.5.11. Fuel transfer pump logic............................................................................................................873.5.12. Alarm jump.................................................................................................................................873.5.13. Command timers.......................................................................................................................88

3.6. System parameters, mains setup.........................................................................................................893.6.1. Test..............................................................................................................................................893.6.2. Mains failure................................................................................................................................90

3.7. System parameters, external communication......................................................................................913.7.1. External communication..............................................................................................................91

3.8. System parameters, engine interface communication.........................................................................923.8.1. Engine interface communication..................................................................................................92

3.9. System parameters, setup menu.........................................................................................................933.9.1. Password config. ........................................................................................................................933.9.2. AC config.....................................................................................................................................933.9.3. Display control ............................................................................................................................93

3.10. System parameters, RMI inputs.........................................................................................................943.10.1. RMI 6.........................................................................................................................................943.10.2. RMI 7.........................................................................................................................................953.10.3. RMI 8.........................................................................................................................................953.10.4. RMI 58.......................................................................................................................................963.10.5. RMI 59.......................................................................................................................................963.10.6. Multi-input selections.................................................................................................................973.10.7. Analogue unit input scaling........................................................................................................98

CGC 400 parameter list 4189340789 UK


1. General information1.1 Warnings, legal information and safety1.1.1 Warnings and notesThroughout this document, a number of warnings and notes with helpful user information will be presented.To ensure that these are noticed, they will be highlighted as follows in order to separate them from the gener-al text.

Warnings

Warnings indicate a potentially dangerous situation, which could result in death, personal in-jury or damaged equipment, if certain guidelines are not followed.

Notes

Notes provide general information, which will be helpful for the reader to bear in mind.

1.1.2 Legal information and disclaimerDEIF takes no responsibility for installation or operation of the generator set. If there is any doubt about howto install or operate the engine/generator controlled by the unit, the company responsible for the installation orthe operation of the set must be contacted.

The unit is not to be opened by unauthorised personnel. If opened anyway, the warranty will belost.

DisclaimerDEIF A/S reserves the right to change any of the contents of this document without prior notice.

1.1.3 Safety issuesInstalling and operating the unit may imply work with dangerous currents and voltages. Therefore, the instal-lation should only be carried out by authorised personnel who understand the risks involved in working withlive electrical equipment.

Be aware of the hazardous live currents and voltages. Do not touch any AC measurement in-puts as this could lead to injury or death.

DEIF do not recommend to use the USB as the primary power supply for the unit.

1.1.4 Electrostatic discharge awarenessSufficient care must be taken to protect the terminal against static discharges during the installation. Once theunit is installed and connected, these precautions are no longer necessary.

CGC 400 parameter list 4189340789 UK General information


1.1.5 Factory settingsThe unit is delivered from factory with certain factory settings. These are based on average values and arenot necessarily the correct settings for matching the engine/generator set in question. Precautions must betaken to check the settings before running the engine/generator set.

1.2 About the Parameter List1.2.1 General purpose of the Parameter ListThis document is a complete parameter list including all parameters, which means that some of the optionparameters included may not be accessible in the system in question.

The document includes a complete standard alarm list and a complete standard parameter list for setup.Therefore, this document is to be used for reference, when information about specific alarms and parametersis needed.

Please make sure to read this document before starting to work with the unit and the genset tobe controlled. Failure to do this could result in human injury or damage to the equipment.

1.2.2 Intended usersThis Parameter List is mainly intended for the person responsible for the unit parameter setup. In most cases,this would be a panel builder designer. Naturally, other users might also find useful information here.

1.2.3 Contents and overall structureThis document is divided into chapters, and in order to make the structure simple and easy to use, eachchapter will begin from the top of a new page.

CGC 400 parameter list 4189340789 UK General information


2. Alarm list2.1 General information about the alarm list2.1.1 Alarm list features and options

In the following, these abbreviations are used:G: GeneratorGB: Generator breakerMB: Mains breakerN/A: Not available

This chapter includes a complete alarm list, including all possible options. Therefore, this chapter is to beused for reference when specific information about the individual parameters is needed for the unit setup.

The table consists of the following possible adjustments:

Set point: The alarm set point is adjusted in the set point menu. The setting is a percentage ofthe nominal values.

Delay: The timer setting is the time that must expire from the alarm level is reached until thealarm occurs.

Relay output A: A relay can be activated by output A.

Relay output B: A relay can be activated by output B.

Enable: The alarm can be activated or deactivated. ON means always activated, RUN meansthat the alarm has run status. This means it is activated when the running signal ispresent.

Fail class: When the alarm occurs the unit will react depending on the selected fail class.

Fail classes are:

Fail class DG (diesel generator) Mains unitF1 Block BlockF2 Warning WarningF3 Trip GB Trip TBF4 Trip + Stop Trip MBF5 Shutdown N/AF6 Trip MB N/AF7 Safety stop N/AF8 Trip MB/GB N/A

Small differences due to the character of the parameters may exist between the individual ta-bles.

CGC 400 parameter list 4189340789 UK Alarm list


It is also possible to configure the param-eters by using the PC utility software. Itwill be possible to make the same config-urations as described above.

By using the PC utility software, extrafunctionality is available. For all the pro-tections it is possible to make an auto-matic acknowledgement of the alarm.



2.2 Protection parameters2.2.1 Reverse power and overcurrent protection

No. Setting Min.Max.

Factorysetting

Notes Ref. Description

1000 Reverse power 11001 P> 1 Set

point-200.0 %0.0 %

-5.0 % DesignersReferenceHandbook

The alarm and fail class are ac-tivated when the reverse powerhas been continuously abovethe programmed value duringthe programmed delay.

1002 P> 1 Timer 0.1 s100.0 s

10.0 s

1003 P> 1 RelayoutputA

Not usedOption-depend-ent

Not used

1004 P> 1 RelayoutputB


Not used

1005 P> 1 Enable OFFON

ON

1006 P> 1 Failclass

F1F8 Trip GB(F3)

1010 Reverse power 21011 P> 2 Set

point-200.0 %0.0 %

-5.0 % DesignersReferenceHandbook

The alarm and fail class are ac-tivated when the reverse powerhas been continuously abovethe programmed value duringthe programmed delay.

1012 P> 2 Timer 0.1 s100.0 s

10.0 s



Not used



Not used


ON

1016 P> 2 Failclass

F1F8 Trip GB(F3)

1030 Overcurrent 1




Factorysetting


1031 I> 1 Setpoint

50.0 %200.0 %

115.0 % DesignersReferenceHandbook

The alarm and fail class are ac-tivated when the current hasbeen continuously above theprogrammed value during theprogrammed delay.

1032 I> 1 Timer 0.1 s3200.0 s

10.0 s

1033 I> 1 RelayoutputA


Not used

1034 I> 1 RelayoutputB


Not used

1035 I> 1 Enable OFFON

ON

1036 I> 1 Failclass

F1F8 Warn-ing(F2)

1040 Overcurrent 21041 I> 2 Set

point50.0 %200.0 %



1042 I> 2 Timer 0.1 s3200.0 s

5.0 s



Not used



Not used


ON

1046 I> 2 Failclass

F1F8 Trip GB(F3)


point50.0 %200.0 %



1052 I> 3 Timer 0.1 s3200.0 s

10.0 s



Not used




Factorysetting




Not used


ON

1056 I> 3 Failclass

F1F8 Trip GB(F3)


point50.0 %200.0 %



1062 I> 4 Timer 0.1 s3200.0 s

5.0 s



Not used



Not used


ON

1066 I> 4 Failclass

F1F8 Trip GB(F3)

1080 I> inverse1081 I> in-

verseType

Setpoint

IEC In-verseCustom

IEC In-verse

DesignersReferenceHandbook

Type selections are:IEC InverseIEC Very InverseIEC Extremely Inv.IEEE Moderately Inv.IEEE Very InverseIEEE Extremely Inv.Custom

Output B is only available in theutility software.

1082 I> in-verseLimit

Setpoint

50 %200 %

110.0 %

1083 I> in-verseTMS

Setpoint

0.1100.0

1.0

1084 I> in-verse k

Setpoint

0.001 s32.000 s

0.140 s

1085 I> in-verse c

Setpoint

0.000 s32.000 s

0.000 s

1086 I> in-verse a

Setpoint

0.00132.000

0.020




Factorysetting


1087 I> in-verse

RelayoutputA


Not used

1088 I> in-verse

Enable OFFON

ON

1089 I> in-verse

Failclass

F1F8 Trip GB(F3)

1130 Fast overcurrent 11131 I>> 1 Set

point150.0 %350.0 %


The alarm settings relate to thenominal current setting. Thealarm and fail class are activa-ted when the current has beencontinuously above the pro-grammed value during the pro-grammed delay.

1132 I>> 1 Timer 0.0 s100.0 s

2.0 s

1133 I>> 1 RelayoutputA


Not used

1134 I>> 1 RelayoutputB


Not used

1135 I>> 1 Enable OFFON

OFF

1136 I>> 1 Failclass

F1...F8 Trip GB(F3)

1140 Fast overcurrent 21141 I>> 2 Set

point150.0 %350.0 %

200 % DesignersReferenceHandbook

The alarm and fail class are ac-tivated when the current hasbeen continuously above theprogrammed value during theprogrammed delay

1142 I>> 2 Delay 0.0 s100.0 s

0.5 s

1143 I>> 2 RelayoutputA


Not used

1144 I>> 2 RelayoutputB


Not used

1145 I>> 2 Enable OFFON

OFF

1146 I>> 2 Failclass

F1...F8 Trip GB(F3)



2.2.2 Voltage protectionsNo. Setting Min.

Max.Factorysetting


1150 G overvoltage 11151 G U>

1Setpoint

100.0 %120.0 %


The alarm and fail class are acti-vated when the voltage has beencontinuously above the program-med value during the program-med delay.

1152 G U>1

Timer 0.1 s100.0 s

10.0 s

1153 G U>1

RelayoutputA

Not usedOption-dep.

Notused

1154 G U>1

RelayoutputB

Not usedOption-dep.

Notused

1155 G U>1

Enable OFFON

OFF

1156 G U>1

Failclass

F1F8 Warning(F2)

1160 G overvoltage 21161 G U>

2Setpoint

100.0 %120.0 %



1162 G U>2

Timer 0.1 s100.0 s

5.0 s

1163 G U>2

RelayoutputA

Not usedOption-dep.

Notused

1164 G U>2

RelayoutputB

Not usedOption-dep.

Notused

1165 G U>2

Enable OFFON

OFF

1166 G U>2

Failclass

F1F8 Warning(F2)

1170 G undervoltage 11171 G U3

Failclass

F1F8 Warning(F2)

1240 G underfrequency 11241 G f


Factorysetting


1254 G f

2.2.4 Busbar voltage protections

Voltage settings relate to the nominal voltage setting.


Factorysetting


1270 Busbar overvoltage 11271 BB

U> 1Setpoint

100.0 %120.0 %



1272 BBU> 1

Timer 0.00 s99.99 s

10.00 s

1273 BBU> 1

RelayoutputA


Notused

1274 BBU> 1

RelayoutputB


Notused

1275 BBU> 1

Enable OFFON

OFF

1276 BBU> 1

Failclass

F1F8 Warning(F2)

1280 Busbar overvoltage 21281 BB

U> 2Setpoint

100.0 %120.0 %



1282 BBU> 2

Timer 0.00 s99.99 s

10.00 s

1283 BBU> 2

RelayoutputA


Notused

1284 BBU> 2

RelayoutputB


Notused

1285 BBU> 2

Enable OFFON

OFF

1286 BBU> 2

Failclass

F1F8 Warning(F2)

1300 Busbar undervoltage 1




Factorysetting


1301 BBU< 1

Setpoint

40.0 %100.0 %


The alarm and fail class are acti-vated when the voltage has beencontinuously under the program-med value during the program-med delay.

1302 BBU< 1

Timer 0.00 s99.99 s

10.00 s

1303 BBU< 1

RelayoutputA


Notused

1304 BBU< 1

RelayoutputB


Notused

1305 BBU< 1

Enable OFFON

OFF

1306 BBU< 1

Failclass

F1F8 Warning(F2)

1310 Busbar undervoltage 21311 BB

U< 2Setpoint

40.0 %100.0 %


The alarm and fail class are acti-vated when the voltage has beencontinuously under the program-med value during the program-med delay.

1312 BBU< 2

Timer 0.00 s99.99 s

5.00 s

1313 BBU< 2

RelayoutputA


Notused

1314 BBU< 2

RelayoutputB


Notused

1315 BBU< 2

Enable OFFON

OFF

1316 BBU< 2

Failclass

F1F8 Warning(F2)



2.2.5 Busbar frequency protections

Frequency settings relate to the nominal frequency setting.


Factorysetting


1350 Busbar overfrequency 11351 BB f>

1Setpoint

100.0 %120.0 %


The alarm and fail class are acti-vated when the frequency hasbeen continuously above the pro-grammed value during the pro-grammed delay.

1352 BB f>1

Timer 0.00 s99.99 s

10.00 s

1353 BB f>1

RelayoutputA

Not usedOption-dep.

Notused

1354 BB f>1

RelayoutputB

Not usedOption-dep.

Notused

1355 BB f>1

Enable OFFON

OFF

1356 BB f>1

Failclass

F1F8 Warning(F2)

1360 Busbar overfrequency 21361 BB f>

2Setpoint

100.0 %120.0 %


The alarm and fail class are acti-vated when the frequency hasbeen continuously above the pro-grammed value during the pro-grammed delay.

1362 BB f>2

Timer 0.00 s99.99 s

5.00 s

1363 BB f>2

RelayoutputA

Not usedOption-dep.

Notused

1364 BB f>2

RelayoutputB

Not usedOption-dep.

Notused

1365 BB f>2

Enable OFFON

OFF

1366 BB f>2

Failclass

F1F8 Warning(F2)

1380 Busbar underfrequency 11381 BB f 2 Failclass

F1F8 Trip GB(F3)

1470 Overload 31471 P> 3 Set

point-200.0 %200.0 %


The alarm and fail class are activa-ted when the power has been con-tinuously above the programmedvalue during the programmed de-lay.

1472 P> 3 Timer 0.1 s3200.0 s

10.0 s


Not usedOption-dep.

Notused




Factorysetting



Not usedOption-dep.

Notused


OFF

1476 P> 3 Failclass

F1F8 Trilp GB(F3)


point-200.0 %200.0 %



1482 P> 4 Timer 0.1 s3200.0 s

5.0 s


Not usedOption-dep.

Notused


Not usedOption-dep.

Notused


OFF

1486 P> 4 Failclass

F1F8 Trip GB(F3)


point-200.0 %200.0 %



1492 P> 5 Timer 0.1 s3200.0 s

10.0 s


Not usedOption-dep.

Notused


Not usedOption-dep.

Notused


OFF

1496 P> 5 Failclass

F1...F8 Trip GB(F3)



2.2.7 Undervoltage and reactive power lowNo. Setting Min.

Max.Factorysetting


1960 U and Q < 11961 U and

Q < 1Setpoint

40.0 %100.0 %

85.0 % Option A1 The setting relates to the genera-tor nominal voltage.The condition for trip is that the ac-tual voltage drops below the set-ting value and the reactive poweris 0 kVAr.

1962 U andQ < 1

Timer 0.1 s3200.0 s

0.5 s

1963 U andQ < 1

RelayoutputA

Option-dep.

Notused

1964 U andQ < 1

RelayoutputB

Option-dep.

Notused

1965 U andQ < 1

Enable OFFON

OFF

1966 U andQ < 1

Failclass

F1F8 Warning(F2)

1970 U and Q < 21971 U and

Q < 2Setpoint

40.0 %100.0 %

85.0 % Option A1 The setting relates to the genera-tor nominal voltage.The condition for trip is that the ac-tual voltage drops below the set-ting value and the reactive poweris 0 kVAr.

1972 U andQ < 2

Timer 0.1 s3200.0 s

0.5 s

1973 U andQ < 2

RelayoutputA

Option-dep.

Notused

1974 U andQ < 2

RelayoutputB

Option-dep.

Notused

1975 U andQ < 2

Enable OFFON

OFF

1976 U andQ < 2

Failclass

F1F8 Warning(F2)

1980 GB/MB external trip1981 GB ext.

tripEnable OFF

ONON Design-

er's Refer-enceHandbook

The generator breaker or themains breaker has been tripped byan external device.1982 GB ext.

tripFailclass

F1...F8 Warning(F2)

1983 MB ext.trip

Enable OFFON

ON

1984 MB ext.trip

Failclass

F1...F8 Warning(F2)



Minimum current and minimum Phi angle


Factorysetting


1990 U and Q< 11991 I Min. 1 Set

point0 %20 %

0 % OptionA1

Settings relate to U and Q< parameters1960 and 1970.Condition for "U and Q

2.3 Breaker control parameters2.3.1 Breaker alarms


Factorysetting


2110 Sync. blackout2111 Sync.

blackoutdfMax. 0.0 Hz

5.0 Hz3.0 Hz Designers

ReferenceHandbook

Settings are accepted limits forclosing of the breaker, refer-ring to nominal frequency andvoltage.

2112 Sync.blackout

dUMax. 2 %10 %

5 %

2150 Phase sequence error2151 Phase

seq er-ror

Relayoutput A

Not usedOption-dep.

Not used DesignersReferenceHandbook

Prior to closing a breaker, theunit checks that the phase se-quence is correct, dependingon the chosen phase directionin parameter 2154: Phase ro-tation. If it is incorrect (re-versed), an alarm will be is-sued and the breaker in ques-tion will not be closed.

2152 Phaseseq er-ror

Relayoutput B

Not usedOption-dep.

Not used

2153 Phaseseq er-ror

Failclass

F1F8 Block(F1)

2154 Phaserotation

Set point L1L2L3L1L3L2

L1L2L3

2160 GB open failure2161 GB

open failTimer 1.0 s

10.0 s2.0 s Designers

ReferenceHandbook

The breaker open failure willoccur if the unit has transmit-ted a breaker open signal andthe breaker feedback has notchanged position from ON toOFF within the time delay.

2162 GBopen fail

Relayoutput A

Not usedOption-dep.

Not used

2163 GBopen fail

Relayoutput B

Not usedOption-dep.

Not used

2164 GBopen fail

Enable OFFON

ON

2165 GBopen fail

Failclass

F1F8 Warning(F2)

2170 GB breaker close failure2171 GB

closefail

Timer 1.0 s5.0 s

2.0 s DesignersReferenceHandbook

The breaker close failure willoccur if the unit has transmit-ted a breaker close signal andthe breaker feedback has notchanged position from OFF toON within the time delay.

2172 GBclosefail

Relayoutput A

Not usedOption-dep.

Not used




Factorysetting


2173 GBclosefail

Relayoutput B

Not usedOption-dep.

Not used

2174 GBclosefail

Enable OFFON

ON

2175 GBclosefail

Failclass

F1F8 Warning(F2)

2180 GB breaker position failure2181 GB pos

failTimer 1.0 s


ReferenceHandbook

This alarm will occur if thebreaker feedbacks for ON andOFF are both missing or activefor more than the time delay.

2182 GB posfail

Relayoutput A

Not usedOption-dep.

Not used

2183 GB posfail

Relayoutput B

Not usedOption-dep.

Not used

2184 GB posfail

Enable OFFON

ON

2185 GB posfail

Failclass

F1F8 Warning(F2)

2200 MB open failure2201 MB

open failTimer 1.0 s


ReferenceHandbook

The breaker open failure willoccur if the unit has transmit-ted a breaker open signal andthe breaker feedback has notchanged position from ON toOFF within the time delay.

2202 MBopen fail

Relayoutput A

Not usedOption-dep.

Not used

2203 MBopen fail

Relayoutput B

Not usedOption-dep.

Not used

2204 MBopen fail

Enable OFFON

ON

2205 MBopen fail

Failclass

F1F8 Warning(F2)

2210 MB close failure2211 MB

closefail

Timer 1.0 s5.0 s


The breaker close failure willoccur if the unit has transmit-ted a breaker close signal andthe breaker feedback has notchanged position from OFF toON within the time delay.

2212 MBclosefail

Relayoutput A

Not usedOption-dep.

Not used




Factorysetting


2213 MBclosefail

Relayoutput B

Not usedOption-dep.

Not used

2214 MBclosefail

Enable OFFON

ON

2215 MBclosefail

Failclass

F1F8 Warning(F2)

2220 MB position failure2221 MB pos

failTimer 1.0 s


ReferenceHandbook

This alarm will occur if thebreaker feedbacks for ON andOFF are both missing or activefor more than the time delay.

2222 MB posfail

Relayoutput A

Not usedOption-dep.

Not used

2223 MB posfail

Relayoutput B

Not usedOption-dep.

Not used

2224 MB posfail

Enable OFFON

ON

2225 MB posfail

Failclass

F1F8 Warning(F2)

No. Setting Min. setting Max. setting Factory setting2770 EIC control2771 EIC control Droop 0.0 % 25.0 % 0.0 %2772 EIC control Scania rpm User

1500 rpm1800 rpmLow Idle

User

2773 EIC control Cummins gain 0.00 10.00 5.002790 EIC speed demand switch2791 EIC speed demand

switchLocal normal sw. Analogue CAN

UpDown ECUUpDown CANAnalogue ECUAnalogue ECU relativeFrequency

Analogue CAN

2792 EIC speed demandswitch

Local emergency sw.


Remote normal sw.


Remote emergency sw.



2.4 Input/output parameters, binary input setup2.4.1 Digital input 10-15 and 56-57 setup


Factorysetting


3000 Digital input 103001 Dig. in-

put 10Timer 0.0 s


ReferenceHandbook

The input is configurableand can have differentfunctions in different units.3002 Dig. in-

put 10Relayoutput A

Not usedOption-dep.

Not used

3003 Dig. in-put 10

Relayoutput B

Not usedOption-dep.

Not used

3004 Dig. in-put 10

Enable OFFON

OFF

3005 Dig. in-put 10

Fail class F1F8 Warning(F2)

3006 Dig. in-put 10

HighAlarm

OFFON

ON

The same settings apply to inputs 11-15 and 56-57, menus 3010 to 3070.



2.4.2 Digital input 6-8 setupNo. Setting Min.

Max.Facto-ry set-

ting


3400 Digital input 63401 Wire

fail 6Enable OFF OFF Designers

ReferenceHandbook

The input is configurable and canhave different functions in differentunits.(Only available if multi-input 6 isconfigured to "binary" in menu10980).

3402 Dig. in-put 6

Timer 0.0 s100.0 s

10.0 s

3403 Dig. in-put 6

RelayoutputA

NotusedOption-dep.

Notused

3404 Dig. in-put 6

RelayoutputB

NotusedOption-dep.

Notused

3405 Dig. in-put 6

Enable OFFON

OFF

3406 Dig. in-put 6

Failclass

F1F8 Warn-ing(F2)

3410 Digital input 73411 Wire

fail 7Enable OFF OFF Designers

ReferenceHandbook


3412 Dig. in-put 7

Timer 0.0 s100.0 s

10.0 s

3413 Dig. in-put 7

RelayoutputA

NotusedOption-dep.

Notused

3414 Dig. in-put 7

RelayoutputB

NotusedOption-dep.

Notused

3415 Dig. in-put 7

Enable OFFON

OFF

3416 Dig. in-put 7

Failclass

F1F8 Warn-ing(F2)

3420 Digital input 8




Facto-ry set-

ting


3421 Wirefail 8

Enable OFF OFF DesignersReferenceHandbook


3422 Dig. in-put 8

Timer 0.0 s100.0 s

10.0 s

3423 Dig. in-put 8

RelayoutputA

NotusedOption-dep.

Notused

3424 Dig. in-put 8

RelayoutputB

NotusedOption-dep.

Notused

3425 Dig. in-put 8

Enable OFFON

OFF

3426 Dig. in-put 8

Failclass

F1F8 Warn-ing(F2)

2.4.3 Emergency stopNo. Setting Min.

Max.Factorysetting


3490 Emergency stop3491 Emer.

stopTimer 0.0 s


ReferenceHandbook

Emergency stop input isintended for a normallyclosed contact.3492 Emer.

stopRelayoutput A

Not usedOption-dependent

Not used

3493 Emer.stop

Relayoutput B

Not usedOption-de-pendent

Not used

3494 Emer.stop

Enable OFFON

ON

3495 Emer.stop

Fail class F1F8 Shut-down(F5)



2.4.4 M-Logic alarm 1-5 setupNo. Setting Min.

Max.Factorysetting


3570 Mlogic alarm 13570 Mlogic alarm 1 Timer 0.0 s

100.0 s10.0 s The input is configura-

ble.3571 Mlogic alarm 1 Relay output

ANot usedOption-dep.

Not used

3572 Mlogic alarm 1 Relay outputB

Not usedOption-dep.

Not used

3573 Mlogic alarm 1 Enable OFFON

OFF

3574 Mlogic alarm 1 Fail class F1F8 Warning(F2)

3575 Mlogic alarm 1 High alarm OFFON

ON

The same settings apply to alarm inputs 2-5, menus 3580 to 3610.



2.5 Analogue input setup2.5.1 Multi-input no. 6

The available menus for multi-input no. 6 depend on the input type configured in the PC utilitysoftware (menu 10980).


Factorysetting


4120 4-20 mA 6.14121 4-20

mA 6.1Setpoint

4 mA20 mA

10 mA DesignersReferenceHandbook

The multi-input 6 has beenconfigured as 4-20 mA.

4122 4-20mA 6.1

Timer 0.0 s999.0 s

120.0 s

4123 4-20mA 6.1

Relayoutput A

Not usedOption-dep.

Notused

4124 4-20mA 6.1

Relayoutput B

Not usedOption-dep.

Notused

4125 4-20mA 6.1

Enable OFFON

OFF

4126 4-20mA 6.1

Failclass

F1F8 Warning(F2)

4130 4-20 mA 6.24131 4-20

mA 6.2Setpoint

4 mA20 mA



4132 4-20mA 6.2

Timer 0.0 s999.0 s

120.0 s

4133 4-20mA 6.2

Relayoutput A

Not usedOption-dep.

Notused

4134 4-20mA 6.2

Relayoutput B

Not usedOption-dep.

Notused

4135 4-20mA 6.2

Enable OFFON

OFF

4136 4-20mA 6.2

Failclass

F1F8 Warning(F2)

4160 Pt100/Pt1000 6.14161 PT 6.1 Set

point-49482

80 DesignersReferenceHandbook

The multi-input 6 has beenconfigured as Pt100 orPt1000.4162 PT 6.1 Timer 0.0 s

999.0 s5.0 s




Factorysetting


4163 Pt100/Pt1000 set point can bein deg. C or F, dependent onthe unit selection (menu10970).

PT 6.1 Relayoutput A

Not usedOption-dep.

Notused

4164 PT 6.1 Relayoutput B

Not usedOption-dep.

Notused

4165 PT 6.1 Enable OFFON

OFF

4166 PT 6.1 Failclass

F1F8 Warning(F2)

4167 PT 6.1 Offset 0.0 Ohm5.0 Ohm

0.0 Ohm

4170 Pt100/Pt1000 6.24171 PT 6.2 Set

point-49482


The multi-input 6 has beenconfigured as Pt100 orPt1000.Pt100/Pt1000 set point can bein deg. C or F, dependent onthe unit selection (menu10970).

4172 PT 6.2 Timer 0.0 s999.0 s

10.0 s

4173 PT 6.2 Relayoutput A

Not usedOption-dep.

Notused


Not usedOption-dep.

Notused


OFF


F1...F8 Warning(F2)

4180 Resistance measurement input, oil pressure 6.14181 RMI oil

6.1Setpoint

0.0145.0

2.0 DesignersReferenceHandbook

The multi-input 6 has beenconfigured as RMI oil pres-sure.Oil pressure set point can bein Bar or PSI, dependent onthe unit selection (menu10970).

4182 RMI oil6.1

Timer 0.0 s999.0 s

5.0 s

4183 RMI oil6.1

Relayoutput A

Not usedOption-dep.

Notused

4184 RMI oil6.1

Relayoutput B

Not usedOption-dep.

Notused

4185 RMI oil6.1

Enable OFFON

OFF

4186 RMI oil6.1

Failclass

F1F8 Warning(F2)




Factorysetting



6.2Setpoint

0.0145.0



4192 RMI oil6.2

Timer 0.0 s999.0 s

5.0 s

4193 RMI oil6.2

Relayoutput A

Not usedOption-dep.

Notused

4194 RMI oil6.2

Relayoutput B

Not usedOption-dep.

Notused

4195 RMI oil6.2

Enable OFFON

OFF

4196 RMI oil6.2

Failclass

F1F8 Shut-down(F5)

4200 Resistance measurement input, water temperature 6.14201 RMI

water6.1

Setpoint

-49482


The multi-input 6 has beenconfigured as RMI water tem-perature.Water temperature set pointcan be in deg. C or F, depend-ent on the unit selection(menu 10970).

4202 RMIwater6.1

Timer 0.0 s999.0 s

5.0 s

4203 RMIwater6.1

Relayoutput A

Not usedOption-dep.

Notused

4204 RMIwater6.1

Relayoutput B

Not usedOption-dep.

Notused

4205 RMIwater6.1

Enable OFFON

OFF

4206 RMIwater6.1

Failclass

F1F8 Warning(F2)


water6.2

Setpoint

-49482



4212 RMIwater6.2

Timer 0.0 s999.0 s

5.0 s




Factorysetting


4213 RMIwater6.2

Relayoutput A

Not usedOption-dep.

Notused

4214 RMIwater6.2

Relayoutput B

Not usedOption-dep.

Notused

4215 RMIwater6.2

Enable OFFON

OFF

4216 RMIwater6.2

Failclass

F1F8 Trip +Stop(F4)

4220 Resistance measurement input, fuel level 6.14221 RMI

fuel 6.1Setpoint

0 %100 %


The multi-input 6 has beenconfigured as RMI fuel level.

4222 RMIfuel 6.1

Timer 0.0 s999.0 s

10.0 s

4223 RMIfuel 6.1

Relayoutput A

Not usedOption-dep.

Notused

4224 RMIfuel 6.1

Relayoutput B

Not usedOption-dep.

Notused

4225 RMIfuel 6.1

Enable OFFON

OFF

4226 RMIfuel 6.1

Failclass

F1F8 Warning(F2)


fuel 6.2Setpoint

0 %100 %



4232 RMIfuel 6.2

Timer 0.0 s999.0 s

10.0 s

4233 RMIfuel 6.2

Relayoutput A

Not usedOption-dep.

Notused

4234 RMIfuel 6.2

Relayoutput B

Not usedOption-dep.

Notused

4235 RMIfuel 6.2

Enable OFFON

OFF

4236 RMIfuel 6.2

Failclass

F1F8 Warning(F2)




Factorysetting


4240 Wire fail 64241 W. fail

6Relayoutput A

Not usedOption-dep.

Notused


The wire break fault detectionis activated.

4242 W. fail6

Relayoutput B

Not usedOption-dep.

Notused

4243 W. fail6

Enable OFFON

OFF

4244 W. fail6

Failclass

F1F8 Warning(F2)



2.5.2 Multi-input no. 7The available menus for multi-input no. 7 depend on the input type configured in the PC utilitysoftware (menu 10990).


Factorysetting


4250 4-20 mA 7.14251 4-20

mA 7.1Setpoint

4 mA20 mA



4252 4-20mA 7.1

Timer 0.0 s999.0 s

120.0 s

4253 4-20mA 7.1

Relayoutput A

Not usedOption-dep.

Notused

4254 4-20mA 7.1

Relayoutput B

Not usedOption-dep.

Notused

4255 4-20mA 7.1

Enable OFFON

OFF

4256 4-20mA 7.1

Failclass

F1F8 Warning(F2)

4260 4-20 mA 7.24261 4-20

mA 7.2Setpoint

4 mA20 mA



4262 4-20mA 7.2

Timer 0.0 s999.0 s

120.0 s

4263 4-20mA 7.2

Relayoutput A

Not usedOption-dep.

Notused

4264 4-20mA 7.2

Relayoutput B

Not usedOption-dep.

Notused

4265 4-20mA 7.2

Enable OFFON

OFF

4266 4-20mA 7.2

Failclass

F1F8 Warning(F2)

4290 Pt100/Pt1000 7.14291 PT 7.1 Set

point-49482



999.0 s5.0 s




Factorysetting



Not usedOption-dep.

Pt100/Pt1000 set point can bein deg. C or F, dependent onthe unit selection (menu10970).

Notused


Not usedOption-dep.

Notused


OFF


F1F8 Warning(F2)


0.0 Ohm

4300 Pt100/Pt1000 7.24301 PT 7.2 Set

point-49482



4302 PT 7.2 Timer 0.0 s999.0 s

10.0 s


Not usedOption-dep.

Notused


Not usedOption-dep.

Notused


OFF


F1...F8 Warning(F2)


7.1Setpoint

0.0145.0



4312 RMI oil7.1

Timer 0.0 s999.0 s

5.0 s

4313 RMI oil7.1

Relayoutput A

Not usedOption-dep.

Notused

4314 RMI oil7.1

Relayoutput B

Not usedOption-dep.

Notused

4315 RMI oil7.1

Enable OFFON

OFF

4316 RMI oil7.1

Failclass

F1F8 Warning(F2)




Factorysetting



7.2Setpoint

0.0145.0



4322 RMI oil7.2

Timer 0.0 s999.0 s

5.0 s

4323 RMI oil7.2

Relayoutput A

Not usedOption-dep.

Notused

4324 RMI oil7.2

Relayoutput B

Not usedOption-dep.

Notused

4325 RMI oil7.2

Enable OFFON

OFF

4326 RMI oil7.2

Failclass

F1F8 Shut-down(F5)


water7.1

Setpoint

-49482



4332 RMIwater7.1

Timer 0.0 s999.0 s

5.0 s

4333 RMIwater7.1

Relayoutput A

Not usedOption-dep.

Notused

4334 RMIwater7.1

Relayoutput B

Not usedOption-dep.

Notused

4335 RMIwater7.1

Enable OFFON

OFF

4336 RMIwater7.1

Failclass

F1F8 Warning(F2)


water7.2

Setpoint

-49482



4342 RMIwater7.2

Timer 0.0 s999.0 s

5.0 s




Factorysetting


4343 RMIwater7.2

Relayoutput A

Not usedOption-dep.

Notused

4344 RMIwater7.2

Relayoutput B

Not usedOption-dep.

Notused

4345 RMIwater7.2

Enable OFFON

OFF

4346 RMIwater7.2

Failclass

F1F8 Trip +Stop(F4)


fuel 7.1Setpoint

0 %100 %



4352 RMIfuel 7.1

Timer 0.0 s999.0 s

10.0 s

4353 RMIfuel 7.1

Relayoutput A

Not usedOption-dep.

Notused

4354 RMIfuel 7.1

Relayoutput B

Not usedOption-dep.

Notused

4555 RMIfuel 7.1

Enable OFFON

OFF

4356 RMIfuel 7.1

Failclass

F1F8 Warning(F2)


fuel 7.2Setpoint

0 %100 %



4362 RMIfuel 7.2

Timer 0.0 s999.0 s

10.0 s

4363 RMIfuel 7.2

Relayoutput A

Not usedOption-dep.

Notused

4364 RMIfuel 7.2

Relayoutput B

Not usedOption-dep.

Notused

4365 RMIfuel 7.2

Enable OFFON

OFF

4366 RMIfuel 7.2

Failclass

F1F8 Warning(F2)




Factorysetting



7Relayoutput A

Not usedOption-dep.

Notused



4372 W. fail7

Relayoutput B

Not usedOption-dep.

Notused

4373 W. fail7

Enable OFFON

OFF

4374 W. fail7

Failclass

F1F8 Warning(F2)





Factorysetting


4380 4-20 mA 8.14381 4-20

mA 8.1Setpoint

4 mA20 mA



4382 4-20mA 8.1

Timer 0.0 s999.0 s

120.0 s

4383 4-20mA 8.1

Relayoutput A

Not usedOption-dep.

Notused

4384 4-20mA 8.1

Relayoutput B

Not usedOption-dep.

Notused

4385 4-20mA 8.1

Enable OFFON

OFF

4386 4-20mA 8.1

Failclass

F1F8 Warning(F2)

4390 4-20 mA 8.24391 4-20

mA 8.2Setpoint

4 mA20 mA



4392 4-20mA 8.2

Timer 0.0 s999.0 s

120.0 s

4393 4-20mA 8.2

Relayoutput A

Not usedOption-dep.

Notused

4394 4-20mA 8.2

Relayoutput B

Not usedOption-dep.

Notused

4395 4-20mA 8.2

Enable OFFON

OFF

4396 4-20mA 8.2

Failclass

F1F8 Warning(F2)

4420 Pt100/Pt1000 8.14421 PT 8.1 Set

point-49482



999.0 s5.0 s




Factorysetting



Not usedOption-dep.

Pt100/Pt1000 set point can bein deg. C or F, dependent onthe unit selection (menu10970).

Notused


Not usedOption-dep.

Notused


OFF


F1F8 Warning(F2)


0.0 Ohm

4430 Pt100/Pt1000 8.24431 PT 8.2 Set

point-49482



4432 PT 8.2 Timer 0.0 s999.0 s

10.0 s


Not usedOption-dep.

Notused


Not usedOption-dep.

Notused


OFF


F1...F8 Warning(F2)


8.1Setpoint

0.0145.0



4442 RMI oil8.1

Timer 0.0 s999.0 s

5.0 s

4443 RMI oil8.1

Relayoutput A

Not usedOption-dep.

Notused

4444 RMI oil8.1

Relayoutput B

Not usedOption-dep.

Notused

4445 RMI oil8.1

Enable OFFON

OFF

4446 RMI oil8.1

Failclass

F1F8 Warning(F2)




Factorysetting



8.2Setpoint

0.0145.0



4452 RMI oil8.2

Timer 0.0 s999.0 s

5.0 s

4453 RMI oil8.2

Relayoutput A

Not usedOption-dep.

Notused

4454 RMI oil8.2

Relayoutput B

Not usedOption-dep.

Notused

4455 RMI oil8.2

Enable OFFON

OFF

4456 RMI oil8.2

Failclass

F1F8 Shut-down(F5)


water8.1

Setpoint

-49482



4462 RMIwater8.1

Timer 0.0 s999.0 s

5.0 s

4463 RMIwater8.1

Relayoutput A

Not usedOption-dep.

Notused

4464 RMIwater8.1

Relayoutput B

Not usedOption-dep.

Notused

4465 RMIwater8.1

Enable OFFON

OFF

4466 RMIwater8.1

Failclass

F1F8 Warning(F2)


water8.2

Setpoint

-49482



4472 RMIwater8.2

Timer 0.0 s999.0 s

5.0 s




Factorysetting


4473 RMIwater8.2

Relayoutput A

Not usedOption-dep.

Notused

4474 RMIwater8.2

Relayoutput B

Not usedOption-dep.

Notused

4475 RMIwater8.2

Enable OFFON

OFF

4476 RMIwater8.2

Failclass

F1F8 Trip +Stop(F4)


fuel 8.1Setpoint

0 %100 %



4482 RMIfuel 8.1

Timer 0.0 s999.0 s

10.0 s

4483 RMIfuel 8.1

Relayoutput A

Not usedOption-dep.

Notused

4484 RMIfuel 8.1

Relayoutput B

Not usedOption-dep.

Notused

4485 RMIfuel 8.1

Enable OFFON

OFF

4486 RMIfuel 8.1

Failclass

F1F8 Warning(F2)


fuel 8.2Setpoint

0 %100 %



4492 RMIfuel 8.2

Timer 0.0 s999.0 s

10.0 s

4493 RMIfuel 8.2

Relayoutput A

Not usedOption-dep.

Notused

4494 RMIfuel 8.2

Relayoutput B

Not usedOption-dep.

Notused

4495 RMIfuel 8.2

Enable OFFON

OFF

4496 RMIfuel 8.2

Failclass

F1F8 Warning(F2)




Factorysetting



8Relayoutput A

Not usedOption-dep.

Notused



4502 W. fail8

Relayoutput B

Not usedOption-dep.

Notused

4503 W. fail8

Enable OFFON

OFF

4504 W. fail8

Failclass

F1F8 Warning(F2)



2.5.4 Speed and running feedback setupNo. Setting Min.

Max.Factorysetting


4510 Overspeed 14511 Over-

speed 1Setpoint

100.0 %150.0 %


The set point in percentagerelates to nominal RPM.

4512 Over-speed 1

Timer 0.0 s100.0 s

5.0 s

4513 Over-speed 1

RelayoutputA

Not usedOption-dep.

Notused

4514 Over-speed 1

RelayoutputB

Not usedOption-dep.

Notused

4515 Over-speed 1

Enable OFFON

OFF

4516 Over-speed 1

Failclass

F1F8 Warn-ing(F2)

4520 Overspeed 24521 Over-

speed 2Setpoint

100.0 %150.0 %



4522 Over-speed 2

Timer 0.0 s100.0 s

1.0 s

4523 Over-speed 2

RelayoutputA

Not usedOption-dep.

Notused

4524 Over-speed 2

RelayoutputB

Not usedOption-dep.

Notused

4525 Over-speed 2

Enable OFFON

OFF

4526 Over-speed 2

Failclass

F1F8 Shut-down(F5)

4530 Crank failure4531 Crank

failureSetpoint

1 RPM400 RPM

50 RPM DesignersReferenceHandbook

If MPU is chosen as the pri-mary running feedback, thisalarm will be raised if thespecified RPM is not reachedbefore the delay has expired.

4532 Crankfailure

Timer 0.0 s20.0 s

2.0 s




Factorysetting


4533 Crankfailure

RelayoutputA

Not usedOption-dep.

Notused

4534 Crankfailure

RelayoutputB

Not usedOption-dep.

Notused

4535 Crankfailure

Enable OFFON

OFF

4536 Crankfailure

Failclass

F1F8 Warn-ing(F2)

4540 Running feedback failure4541 Run

feedb.fail

Timer 0.0 s20.0 s


If running is detected on thefrequency (secondary), butthe primary running feedback,e.g. digital input, has not de-tected running, this alarm willbe raised after the adjusteddelay time.

4542 Runfeedb.fail

RelayoutputA

Not usedOption-dep.

Notused

4543 Runfeedb.fail

RelayoutputB

Not usedOption-dep.

Notused

4544 Runfeedb.fail

Enable OFFON

ON

4545 Runfeedb.fail

Failclass

F1...F8 Warn-ing(F2)

4560 Hz/voltage failure4561 Hz/V fail-

ureTimer 1.0 s


ReferenceHandbook

If the frequency and voltageare not within the limits afterthe running feedback is re-ceived, this alarm will beraised when the delay timehas expired. Limits are placedin menu 2110 (Sync. black-out).

4562 Hz/V fail-ure

RelayoutputA

Not usedOption-dep.

Notused

4563 Hz/V fail-ure

RelayoutputB

Not usedOption-dep.

Notused

4564 Hz/V fail-ure

Enable OFFON

ON

4565 Hz/V fail-ure

Failclass

F1...F8 Shut-down(F5)

4570 Start failure




Factorysetting


4571 Start fail-ure

RelayoutputA

Not usedOption-dep.

Notused


The start failure alarm occursif the genset has not startedafter the number of start at-tempts.4572 Start fail-

ureRelayoutputB

Not usedOption-dep.

Notused

4573 Start fail-ure

Failclass

F1F8 Block(F1)

4580 Stop failure4581 Stop fail-

ureTimer 10.0 s


ReferenceHandbook

A stop failure alarm will ap-pear if the primary runningfeedback or the generatorvoltage and frequency are stillpresent after the delay timehas expired.

4582 Stop fail-ure

RelayoutputA

Not usedOption-dep.

Notused

4583 Stop fail-ure

RelayoutputB

Not usedOption-dep.

Notused

4584 Stop fail-ure

Enable OFFON

ON

4585 Stop fail-ure

Failclass

F1F8 Shut-down(F5)

4590 Underspeed 14591 Under-

speedSetpoint

50.0 %100.0 %



4592 Under-speed

Timer 0.0 s100.0 s

5.0 s

4593 Under-speed

RelayoutputA

Not usedOption-dep.

Notused

4594 Under-speed

RelayoutputB

Not usedOption-dep.

Notused

4595 Under-speed

Enable OFFON

OFF

4596 Under-speed

Failclass

F1F8 Warn-ing(F2)



2.5.5 Differential measurementNo. Setting Min.

Max.Factorysetting


4600 Delta ana 1/2/3 Inp4601 Delta

ana1 InpASet point Multi-input

6EIC

Multi-in-put 6

Designers Ref-erence Hand-book

Delta analogue Inp1/2/3 setting.Choose betweenmulti-inputs, externalanalogue inputs andEIC values

4602 Deltaana1 InpB

Set point Multi-input6EIC

Multi-in-put 6

4603 Deltaana2 InpA


Multi-in-put 6

4604 Deltaana2 InpB


Multi-in-put 6

4605 Deltaana3 InpA


Multi-in-put 6

4606 Deltaana3 InpB


Multi-in-put 6

4610 Delta ana1 14611 Delta

ana1 1Set point -9999

999910 Designers Ref-

erence Hand-book

Delta analogue alarmsetting 1.1

4612 Deltaana1 1

Timer 0.0 s999.0 s

5.0 s

4613 Deltaana1 1

Relayoutput A

Not usedOption-dep.

Not used

4614 Deltaana1 1

Relayoutput B

Not usedOption-dep.

Not used

4615 Deltaana1 1

Enable OFFON

OFF

4616 Deltaana1 1

Failclass

F1F8 Warning(F2)




erence Hand-book


4622 Deltaana1 2

Timer 0.0 s999.0 s

5.0 s

4623 Deltaana1 2

Relayoutput A

Not usedOption-dep.

Not used




Factorysetting


4624 Deltaana1 2

Relayoutput B

Not usedOption-dep.

Not used

4625 Deltaana1 2

Enable OFFON

OFF

4626 Deltaana1 2

Failclass

F1F8 Warning(F2)




erence Hand-book


4632 Deltaana2 1

Timer 0.0 s999.0 s

5.0 s

4633 Deltaana2 1

Relayoutput A

Not usedOption-dep.

Not used

4634 Deltaana2 1

Relayoutput B

Not usedOption-dep.

Not used

4635 Deltaana2 1

Enable OFFON

OFF

4636 Deltaana2 1

Failclass

F1F8 Warning(F2)




erence Hand-book


4642 Deltaana2 2

Timer 0.0 s999.0 s

5.0 s

4643 Deltaana2 2

Relayoutput A

Not usedOption-dep.

Not used

4644 Deltaana2 2

Relayoutput B

Not usedOption-dep.

Not used

4645 Deltaana2 2

Enable OFFON

OFF

4646 Deltaana2 2

Failclass

F1...F8 Warning(F2)




erence Hand-book


4652 Deltaana3 1

Timer 0.0 s999.0 s

5.0 s

4653 Deltaana3 1

Relayoutput A

Not usedOption-dep.

Not used

4654 Deltaana3 1

Relayoutput B

Not usedOption-dep.

Not used




Factorysetting


4655 Deltaana3 1

Enable OFFON

OFF

4656 Deltaana3 1

Failclass

F1...F8 Warning(F2)




erence Hand-book


4662 Deltaana3 2

Timer 0.0 s999.0 s

5.0 s

4663 Deltaana3 2

Relayoutput A

Not usedOption-dep.

Not used

4664 Deltaana3 2

Relayoutput B

Not usedOption-dep.

Not used

4665 Deltaana3 2

Enable OFFON

OFF

4666 Deltaana3 2

Failclass

F1...F8 Warning(F2)



2.5.6 Aux. supply setupNo. Setting Min.

Max.Factorysetting


4960 U< auxiliary power supply terminal 14961 U< aux.

term. 1Setpoint

8.0 Vdc32.0 Vdc

18.0 Vdc DesignersReferenceHandbook

The power supply on terminal1 and 2 has been continu-ously below the adjusted setpoint during the programmeddelay.

4962 U< aux.term. 1

Timer 10.0 s999.0 s

10.0 s

4963 U< aux.term. 1

Relayoutput A

Not usedOption-dep.

Not used

4964 U< aux.term. 1

Relayoutput B

Not usedOption-dep.

Not used

4965 U< aux.term. 1

Enable OFFON

ON

4966 U< aux.term. 1

Failclass

F1F8 Warning(F2)

4970 U> auxiliary power supply terminal 14971 U> aux.

term. 1Setpoint

12.0 Vdc36.0 Vdc

30.0 Vdc DesignersReferenceHandbook

The power supply on terminal1 and 2 has been continu-ously above the adjusted setpoint during the programmeddelay.

4972 U> aux.term. 1

Timer 10.0 s999.0 s

10.0 s

4973 U> aux.term. 1

Relayoutput A

Not usedOption-dep.

Not used

4974 U> aux.term. 1

Relayoutput B

Not usedOption-dep.

Not used

4975 U> aux.term. 1

Enable OFFON

ON

4976 U> aux.term. 1

Failclass

F1F8 Warning(F2)





Factorysetting



put 58Enable OFF

ONOFF Designers

ReferenceHandbook

The input is configurable andcan have different functions indifferent units.The multi-input 58 has beenconfigured as Binary.

4742 Dig. in-put 58

Timer 0.0 s999.0 s

10.0 s

4743 Dig. in-put 58

RelayoutputA

Not usedOption-dep.

Notused

4744 Dig. in-put 58

RelayoutputB

Not usedOption-dep.

Notused

4745 Dig. in-put 58

Enable OFFON

OFF

4746 Dig. in-put 58

Failclass

F1F8 Warning(F2)

4740 4-20 mA 58.14741 4-20

mA58.1

Setpoint

4 mA20 mA



4742 4-20mA58.1

Timer 0.0 s999.0 s

120.0 s

4743 4-20mA58.1

RelayoutputA

Not usedOption-dep.

Notused

4744 4-20mA58.1

RelayoutputB

Not usedOption-dep.

Notused

4745 4-20mA58.1

Enable OFFON

OFF

4746 4-20mA58.1

Failclass

F1F8 Warning(F2)

4750 4-20 mA 58.2




Factorysetting


4751 4-20mA58.2

Setpoint

4 mA20 mA



4752 4-20mA58.2

Timer 0.0 s999.0 s

120.0 s

4753 4-20mA58.2

RelayoutputA

Not usedOption-dep.

Notused

4754 4-20mA58.2

RelayoutputB

Not usedOption-dep.

Notused

4755 4-20mA58.2

Enable OFFON

OFF

4756 4-20mA58.2

Failclass

F1F8 Warning(F2)

4740 Pt100/Pt1000 58.14741 PT

58.1Setpoint

-49482



4742 PT58.1

Timer 0.0 s999.0 s

5.0 s

4743 PT58.1

RelayoutputA

Not usedOption-dep.

Notused

4744 PT58.1

RelayoutputB

Not usedOption-dep.

Notused

4745 PT58.1

Enable OFFON

OFF

4746 PT58.1

Failclass

F1F8 Warning(F2)

4750 Pt100/Pt1000 58.24751 PT

58.2Setpoint

-49482



4752 PT58.2

Timer 0.0 s999.0 s

10.0 s

4753 PT58.2

RelayoutputA

Not usedOption-dep.

Notused




Factorysetting


4754 PT58.2

RelayoutputB

Not usedOption-dep.

Notused

4755 PT58.2

Enable OFFON

OFF

4756 PT58.2

Failclass

F1...F8 Warning(F2)


58.1Setpoint

0.0145.0



4742 RMI oil58.1

Timer 0.0 s999.0 s

5.0 s

4743 RMI oil58.1

RelayoutputA

Not usedOption-dep.

Notused

4744 RMI oil58.1

RelayoutputB

Not usedOption-dep.

Notused

4745 RMI oil58.1

Enable OFFON

OFF

4746 RMI oil58.1

Failclass

F1F8 Warning(F2)


58.2Setpoint

0.0145.0



4752 RMI oil58.2

Timer 0.0 s999.0 s

5.0 s

4753 RMI oil58.2

RelayoutputA

Not usedOption-dep.

Notused

4754 RMI oil58.2

RelayoutputB

Not usedOption-dep.

Notused

4755 RMI oil58.2

Enable OFFON

OFF

4756 RMI oil58.2

Failclass

F1F8 Shut-down(F5)


water58.1

Setpoint

-49482


The multi-input 58 has beenconfigured as RMI water tem-perature.




Factorysetting


4742 Water temperature set pointcan be in deg. C or F, depend-ent on the unit selection (menu10970).

RMIwater58.1

Timer 0.0 s999.0 s

5.0 s

4743 RMIwater58.1

RelayoutputA

Not usedOption-dep.

Notused

4744 RMIwater58.1

RelayoutputB

Not usedOption-dep.

Notused

4745 RMIwater58.1

Enable OFFON

OFF

4746 RMIwater58.1

Failclass

F1F8 Warning(F2)


water58.2

Setpoint

-49482


The multi-input 58 has beenconfigured as RMI water tem-perature.Water temperature set pointcan be in deg. C or F, depend-ent on the unit selection (menu10970).

4752 RMIwater58.2

Timer 0.0 s999.0 s

5.0 s

4753 RMIwater58.2

RelayoutputA

Not usedOption-dep.

Notused

4754 RMIwater58.2

RelayoutputB

Not usedOption-dep.

Notused

4755 RMIwater58.2

Enable OFFON

OFF

4756 RMIwater58.2

Failclass

F1F8 Trip +Stop(F4)


fuel58.1

Setpoint

0 %100 %



4742 RMIfuel58.1

Timer 0.0 s999.0 s

10.0 s




Factorysetting


4743 RMIfuel58.1

RelayoutputA

Not usedOption-dep.

Notused

4744 RMIfuel58.1

RelayoutputB

Not usedOption-dep.

Notused

4745 RMIfuel58.1

Enable OFFON

OFF

4746 RMIfuel58.1

Failclass

F1F8 Warning(F2)


fuel58.2

Setpoint

0 %100 %



4752 RMIfuel58.2

Timer 0.0 s999.0 s

10.0 s

4753 RMIfuel58.2

RelayoutputA

Not usedOption-dep.

Notused

4754 RMIfuel58.2

RelayoutputB

Not usedOption-dep.

Notused

4755 RMIfuel58.2

Enable OFFON

OFF

4756 RMIfuel58.2

Failclass

F1F8 Warning(F2)


58RelayoutputA

Not usedOption-dep.

Notused



4762 W. fail58

RelayoutputB

Not usedOption-dep.

Notused

4763 W. fail58

Enable OFFON

OFF

4764 W. fail58

Failclass

F1F8 Warning(F2)





Factorysetting



put 59Enable OFF

ONOFF Designers

ReferenceHandbook

The input is configurable andcan have different functions indifferent units.The multi-input 59 has beenconfigured as Binary.

4772 Dig. in-put 59

Timer 0.0 s999.0 s

10.0 s

4773 Dig. in-put 59

RelayoutputA

Not usedOption-dep.

Notused

4774 Dig. in-put 59

RelayoutputB

Not usedOption-dep.

Notused

4775 Dig. in-put 59

Enable OFFON

OFF

4776 Dig. in-put 59

Failclass

F1F8 Warning(F2)

4770 4-20 mA 59.14771 4-20

mA59.1

Setpoint

4 mA20 mA



4772 4-20mA59.1

Timer 0.0 s999.0 s

120.0 s

4773 4-20mA59.1

RelayoutputA

Not usedOption-dep.

Notused

4774 4-20mA59.1

RelayoutputB

Not usedOption-dep.

Notused

4775 4-20mA59.1

Enable OFFON

OFF

4776 4-20mA59.1

Failclass

F1F8 Warning(F2)

4780 4-20 mA 59.2




Factorysetting


4781 4-20mA59.2

Setpoint

4 mA20 mA



4782 4-20mA59.2

Timer 0.0 s999.0 s

120.0 s

4783 4-20mA59.2

RelayoutputA

Not usedOption-dep.

Notused

4784 4-20mA59.2

RelayoutputB

Not usedOption-dep.

Notused

4785 4-20mA59.2

Enable OFFON

OFF

4786 4-20mA59.2

Failclass

F1F8 Warning(F2)

4770 Pt100/Pt1000 59.14771 PT

59.1Setpoint

-49482



4772 PT59.1

Timer 0.0 s999.0 s

5.0 s

4773 PT59.1

RelayoutputA

Not usedOption-dep.

Notused

4774 PT59.1

RelayoutputB

Not usedOption-dep.

Notused

4775 PT59.1

Enable OFFON

OFF

4776 PT59.1

Failclass

F1F8 Warning(F2)

4780 Pt100/Pt1000 59.24781 PT

59.2Setpoint

-49482



4782 PT59.2

Timer 0.0 s999.0 s

10.0 s

4783 PT59.2

RelayoutputA

Not usedOption-dep.

Notused




Factorysetting


4784 PT59.2

RelayoutputB

Not usedOption-dep.

Notused

4785 PT59.2

Enable OFFON

OFF

4786 PT59.2

Failclass

F1...F8 Warning(F2)


59.1Setpoint

0.0145.0



4772 RMI oil59.1

Timer 0.0 s999.0 s

5.0 s

4773 RMI oil59.1

RelayoutputA

Not usedOption-dep.

Notused

4774 RMI oil59.1

RelayoutputB

Not usedOption-dep.

Notused

4775 RMI oil59.1

Enable OFFON

OFF

4776 RMI oil59.1

Failclass

F1F8 Warning(F2)


59.2Setpoint

0.0145.0



4782 RMI oil59.2

Timer 0.0 s999.0 s

5.0 s

4783 RMI oil59.2

RelayoutputA

Not usedOption-dep.

Notused

4784 RMI oil59.2

RelayoutputB

Not usedOption-dep.

Notused

4785 RMI oil59.2

Enable OFFON

OFF

4786 RMI oil59.2

Failclass

F1F8 Shut-down(F5)


water59.1

Setpoint

-49482


The multi-input 59 has beenconfigured as RMI water tem-perature.




Factorysetting


4772 Water temperature set pointcan be in deg. C or F, depend-ent on the unit selection (menu10970).

RMIwater59.1

Timer 0.0 s999.0 s

5.0 s

4773 RMIwater59.1

RelayoutputA

Not usedOption-dep.

Notused

4774 RMIwater59.1

RelayoutputB

Not usedOption-dep.

Notused

4775 RMIwater59.1

Enable OFFON

OFF

4776 RMIwater59.1

Failclass

F1F8 Warning(F2)


water59.2

Setpoint

-49482


The multi-input 59 has beenconfigured as RMI water tem-perature.Water temperature set pointcan be in deg. C or F, depend-ent on the unit selection (menu10970).

4782 RMIwater59.2

Timer 0.0 s999.0 s

5.0 s

4783 RMIwater59.2

RelayoutputA

Not usedOption-dep.

Notused

4784 RMIwater59.2

RelayoutputB

Not usedOption-dep.

Documents

CGC 400 parameter list 4189340789 UK_2013.12.13