�e CFR Tunnel Racks are designed to go on the back of most snowmo-biles with a 141” or longer tunnel. �ey are made from strong yet light-weight structural tubular aluminium. �e CFR Tunnel Racks are designed to carry extra fuel, backpacks, ski boots, etc. CFR also manu-factures a complete line of waterproof bags that are designed to �t seam-lessly with our racks, to keep your gear extra dry. If you need to carry skis, snowboards, or pow surfers we o�er a complete line of brackets that bolt to the side of our racks to keep your gear secure and out of your way.

We are constantly working on making our product line up better every year. �e release of the new Mountain rack is as cutting edge as snowmo-bile racks get.�e overall height is a low pro�le 3 3/4". Dropping the center of mass lowers all weight that is carried in the rack allowing the snowmobile to perform better under load.�e CFR Mountain racks design also allows the rack to be mounted on the edge of the tunnel. �is will allow Ski Doo XM factory Holes to be used to install the rack requiring no drilling into the rear tunnel. �e new design is also engineered to use fewer materials than existing racks yet still be as strong.

Rider: Rob Alford Photo: Geo� Kyle

2014/2015Snowmobile Racks

and Accessories

2014/2015Snowmobile Racks

and Accessories

Photo: Eric Berger Skeet shooters: Eric Pehota and Dan Treadway

Tunnel RacksMountain Rack.......................................................................Page 2Irack.........................................................................................Page 3

Bracket KitsBoardski Bracket Kit..............................................................Page 4Snowboard Bracket Kit..........................................................Page 5Single Ski Bracket...................................................................Page 6Dual Ski Bracket.....................................................................Page 7Powder Surf Bracket...............................................................Page 8

Bag Divison Buck Bag..................................................................................Page 9Dime Bag................................................................................Page 10QP Bag....................................................................................Page 11

Direct Tunnel MountBoardski Rack System DTM...............................................Page 12Metal Snowboard Rack System DTM................................Page 13Metal Ski Rack System DTM...............................................Page 14

Snowmobile Control Divison Boondocker.............................................................................Page15Boondocker 2.0......................................................................Page16Brett Turcotte Bar..................................................................Page 17Dan Treadway Bar.................................................................Page 18Dan Treadway 2.0 Bar...........................................................Page 19Knucks Risers........................................................................Page 20

AccessoriesSnowmobile Wraps...............................................................Page 21Connect System.....................................................................Page 22Blades......................................................................................Page 23Spare Parts..............................................................................Page 24Accessories.............................................................................Page 25

Index

Mountain Rack

�e CFR Tunnel Racks are designed to go on the back of most snowmobiles with a 141” or longer tunnel. �ey are made from strong yet lightweight structural tubular aluminium. �e CFR Tunnel Racks are designed to carry extra fuel, backpacks, ski boots, etc. CFR also manufactures a complete line of waterproof bags that are designed to �t seamlessly with our racks, to keep your Extra gear dry. If you need to carry skis, snowboards, or pow surfers we o�er a complete line of brackets that bolt to the side of our racks to keep your equipment secure and out of your way.

Last years release of the Mountain rack was a huge success. �e response from the the low pro-�le 3 3/4" height rack weighing in at a featherweight 3.8 pounds was overwhelming. Customers noticed that by dropping the center of mass, and lowering all the weight that is carried in the rack, there snowmobile performed better under load. �e Mountain racks design allowing Ski Doo XM factory Holes to be used to install the rack was an added bonus as well. �e abuse of rollovers and bumpy access roads were no match for the strong yet lightweight Mountain rack. A unanimous winner!

Features include:-Made from extremely strong and lightweight 3/4”structural tubular aluminum.-Mounting Plates wrap around the sides of the rack for super strength.-Professional Welds for long lasting results.-All mounting Hardware included is made from high grade stainless steel. Super strong and rust Free-Carries up to a 20L 6 G fuel container.-Carries up to 2 pairs of Skis/Snowboards with proper attachments (Sold Separately)-Mounts to most snowmobiles with a 141" track or longer.-Compatible with CFR Dime Bag and QP Bag.

Specs-Mounting plate lines up with Ski Doo XM snowmobiles factory holes. -Outside Rack dimensions Height - 4 " Length - 13 1/2" Width - 17" -Inside Rack dimensions Length - 10 3/4" Width - 15 1/4"-Mounting Plate dimensions Length - 13 1/2" Width - 2 1/2" Weight - 3.8 lbs

Tunnel Racks

Part# TR04

Photo - Mason Mashon

2

iRack�e irack is celebrating its 5th year in our products line up. �e 4 3/4" overall height weighing in at 4lb has proven itself year a�er year! �e CFR Connect system was designed around the strong yet lightweight rack.

Features include:- Available with CFR Connect system that allows irack to be put on and taken o� snowmobile without any tools. (Sold separately and only available on ski doo XM and XP snowmobiles.)-Made from extremely strong and lightweight 3/4”structural tubular aluminum.-Mounting Plates wrap around the sides of the rack for super strength.-Professional Welds for long lasting results.-All mounting Hardware included is made from high grade stainless steel. Super strong and rust Free-Carries up to a 20L 6 G fuel container.-Carries up to 2 pairs of Skis/Snowboards with proper attachments (Sold Separately)-Mounts to most snowmobiles with a 141" track or longer.-Compatible with CFR Dime Bag and QP Bag.

Specs,-Outside Rack dimensions Height - 4 3/4" Length - 15 1/2" Width - 16 3/4" Inside Rack dimensions Length - 10 7/8" Width - 15 1/8"-Mounting Plate dimensions Length - 12 1/2" Width - 2 1/2" Weight - 4 lbs

Photo: Russel Dalby Rider: Dan Treadway

Part# TR03

3

Boardski bracket Kit

CFR Bracket Kits are designed to be attached to the CFR Mountain Rack, iRack, DD and D racks. Each CFR Bracket is Designed to carry skis, snowboards, no boards, and powder surfers. �e Bracket Kits attach to the side of the CFR racks enabling up to two bracket kits to be attached to each rack. (Using the single ski brackets system only allows one bracket kit to be used)

�e Boardski Bracket Kit can carry one snowboard or one pair of skis and poles on the side of the DD, iRack or Mountain Rack. It's the go to bracket for people who both ski and snowboard or have friends that ski and snowboard. Nothing has been compromised in the design securing both skis or snowboards.

Features:-Carries one pair of skis/poles or one snowboard.-Light weight Nylon parts are infused with resin that makes them extremely strong and can handle -100 degree cold temps.-Custom made Injected moulded straps that wont break in the cold but will break in severe roll overs to prevent damage.-Ratchets and Ladders are custom made for superior ratcheting capabilities.-All mounting Hardware included is made from high grade stainless steel. -Super strong and rust Free.-Another Dual Ski bracket kit, Boardski bracket kit, Pow surf bracket kit or snowboard bracket kit can be used on other side of rack. -Speci�cally designed to be fastened to CFR DD, iRack or Mountain Rack. (Sold separately)

CFR Bracket Kits

Part# K04

Photo: db Snowmobiler: Johnny Foon4

Snowboard bracket kit�e snowmobile Snowboard rack that is tested and approved by professional snowboarders Travis Rice, Mark Carter, Mark Landvik, Helen Schettini and Annie Boulanger. �e CFR Snowboard Bracket Kit will keep your snowboard out of the way while snowmobiling. You will forget that you have your snowboard with you breaking trail to the top of your favorite snowboard line or jump spot. �is package contains parts and hardware to carry one snowboard on D, DD, i or Mountain Rack. Another Snowboard Bracket Kit can be purchased to carry up to two Snowboards.

Features:-Professionally used and approved by Snowboarders Travis Rice, Mark Carter, Mark Landvik, Helen Schettini and Annie Boulanger.-Light weight Nylon parts are infused with resin that makes them extremely strong and can handle -100 degree cold temps.-Injected molded straps that can withstand down to -100 degree cold temps but will break in severe roll overs to prevent damage.-Ratchets and Ladders are custom made for superior ratcheting lockdown.-All mounting Hardware included is made from high grade stainless steel. (Super strong and rust Free)-Carries one snowboard. Another Snowboard Bracket Kit can be purchased to carry up to two snowboards.

Photo: db Shredder: Brian Hockenstien

Part# K01

5

Single ski bracket kit�e CFR single ski brackets system is designed to be mounted to D, DD, iRack or Mountain Rack. �is set up evenly distributes the weight of both skis and poles by carrying one ski and pole on each side of rack. No other attachments are possible.

Features:-Light weight Nylon parts are infused with resin that makes them extremely strong and can handle -100 degree cold temps.-Custom made Injected molded straps that wont break in the cold but will break in severe roll overs to prevent damage-Ratchets and Ladders are custom made for superior ratcheting capabilities-All mounting Hardware included is made from high grade stainless steel. -Super strong and rust Free-Carries one ski and pole on each side of snowmobile. No other Brackets can be used with this system.-Speci�cally designed to be fastened to CFR D/DD/i or Mountain Rack

Photo - Blake JorgensonSkier - Dave Treadway

Part# K03

6

Dual Ski Bracket Kit�e CFR Dual Ski Bracket Kit will keep your skis and poles out of the way while breaking trail to your favourite line or jump spot. �is system can be used with another dual ski bracket kit to carry up to two pairs of skis and poles.

It also can be used with a snowboard bracket kit to carry a snowboard on one side of snowmobile and skis/poles on the other side of snowmobile. When two dual ski bracket kits are being used it is putting a lot of extra weight on the rear tunnel. Slow down going through rough conditions. Extra tunnel upports are a good idea if you frequently travel in rough conditions with two pairs of skis.�e Dual Ski Bracket kit is speci�cally designed to be attached to the CFR DD, iRack or Mountain rack

Features:-Professionally approved by Skiers Dan Treadway, Ian McIntosh, Dana Flahr,Seth Morrison and Sage Cattabriga.-Light weight Nylon parts are infused with resin that makes them extremely strong and can handle -100 degree cold temps.-Custom made Injected molded straps can handle -100 degree cold but will break in severe roll overs to prevent damage.-Ratchets and Ladders are custom made for superior ratcheting lock-down. -All mounting Hardware included is made from high grade stainless steel. Super strong and rust Free-Carries one pair of skis and poles. Another Dual Ski bracket kit can be purchased to carry up to two pairs of skis-Speci�cally designed to be fastened to CFR DD, iRack or Mountain Rack.

Photo - Blake JorgensonSledskiers- Dave Treadway and friends!

Part# K02

7

Pow Surf Bracket Kit�e CFR Snowboard/Pow surf bracket is a result of a direct collaboration with Jeremy Jensen at Grassroots pows sur�ng and CFR. Jeremy needed a rack on his snowmobile to carry his Pow surfers. �e Current CFR snowboard bracket kit he had been using worked great for his snowboard but didn't work with his pow surfers.

We hit the drawing board and designed a new bracket that worked both to carry his revolutionary binding-less snow riding Pow surfers and his regular snowboard when he had to use bindings. If you want to carry your Pow surfer or snowboard on your snowmobile this is the bracket for you.

Features:-Professionally used and approved by Grassroots Founder Jeremy Jensen-Light weight Nylon parts are infused with resin that makes them extremely strong and can handle -100 degree cold temps-Injected molded straps that wont break in the cold but will break in severe roll overs to prevent damage-Ratchets and Ladders are custom made for superior ratcheting capabilities-All mounting Hardware included is made from high grade stainless steel. -Super strong and rust Free-Carries one snowboard or Pow Surf bracket-Speci�cally designed to be fastened to CFR D, DD, i and Mountain rack

Surfer- Jeremy JensonPhoto- powsurf.com

Part# K05

8

Buck Bag

�e CFR Bag Division was developed to utilize certain key spots on the snow-mobile to carry much needed extra gear. Our goal was to only have the essen-tials in your backpack and pockets. Lightening up your load when sledding and shredding is a must have for high performance manoeuvres. �e Bags are waterproof and can withstand the hardest winter conditions you will face and keep your gear dry and accessible.

�e new CFR handlebar bag conveniently attaches between the handlebars of most snowmobiles. �e rip stop waterproof fabric along with waterproofzippers keep you goods dry on the wettest days.

Using the CFR handlebar bag lets you empty your jacket and pant pockets keeping all of your go to stu� in one go to spot. With your jacket and pants pocket empty you can boondock your snowmobile through the trickiest terrain and side hill for miles.

9” of clearance is needed on XM snowmobiles between the top of the bag to the DESS switch. If clearance is not available the bag can knock the DESS switch out when turning sharply. Otherwise the Dess switch can be relocated if you still want to rock the buck bag if you don’t have clearance.

Bag Division

Part# B03

Photo - db

9

Dime Bag�e CFR Dime Bag was designed by Pemberton, BC Canada based FYI designs. Tom Routh head designer/snowboard legend/sled/moto head wanted a waterproof and super tough bag for his CFR rack. �e Dime Bag was the result. Tom chose leading fabric maker Dimension Polyent for the outer shell because of its super tough and waterproof characteristics.

�e CFR Dime Bag has Velcro strips that wrap around the CFR DD, i and Mountain racks tubularbars in four spots to keep the bag locked into place. �e waterproof zipper on the outside will keep your contents dry. �e inside waterproof pocket is perfect for your wallet and the key hook keeps your keys in the right place.

A CFR scraper comes standard in all Dime Bags so you can scrape the un wanted ice build up on your snowboard/skis and running boards. �e CFR Dime Bag allows 10 cubic inches of carrying capacity. Now you can bring along your �rst aid kit, tow rope, siphon hoses, beverages or whatever else you might need for your winter adventures.

-Speci�cally designed to be fastened to CFR D/DD/i or Mountain Rack

Part# B01

Photo - dbTandemers- db and Delaney

10

QP Bag�e CFR QP Bag o�ers 25 liters of waterproof carrying capacity and �ts snugly in all of the CFR rack systems. �e QP is a telescoping bag that doubles in size with a quick zipper extension to carry up to 50 liters of gear.

Features:

-Cordura waterproof fabric.-Waterproof zippers.-25 liter capacity. Un-zip the extension and up to 50 liters of capacity are possible.-Clips right into all CFR tunnel rack systems and is easily removable.-Shovel holder on the top enables a shovel to be carried on the deep days for quick access.-Convenient carrying handle.-Individual inside pocket.

Photo: db Tandamers: db and Jake Bauer

Part# B02

11

Board-Ski Bracket System (DTM)Part# M03

�e CFR direct tunnel mount (DTM) rack systems are designed to be attached directly to the rear tunnel of most snowmobiles. No other rack required.

�e ability to carry either a pair of skis and or a snowboards with no other rack required is now a reality. Just buy this bracket, bolt it to your snowmobile, throw your skis and or snowboard on and go. �is is for the minimalist who doesn't want the rack on the back and just wants to carry his skis and or snowboards depending on their fancy for the day.

Features:-�e CFR DTM Boardski bracket bolts to the side of most snowmobiles. (Does not work on 2007 and newer Polaris snowmobiles, 2012 and newer Arctic Cat snowmobiles or 2003-2007 Ski-doo revs.-Two Nylon infused polyurethane brackets carry snowboard and or skis securely and safely.-Custom made injection molded nylon straps keep your gear tightly secured!-CFR uses custom Ratchets designed to be used under very high tensile loads with thicker springs and ratcheting mechanisms.-Carries either a pair of skis and poles or a snowboard.-Another DTM Boardski bracket system can be purchased to carry up to two skis and or snowboards.-Top vertical Holes line up with pre drilled Ski Doo XM’s factory hole pattern.

Direct Tunnel Mount

Photo: Jussi Grznar

12

Metal Snowboard Rack System (DTM)�e snowboard rack tested and approved by snowboarders Eric Jackson, Bjorn Leines and Mads Johnson. �e Metal snowboard rack System is one of the lightest snowboard brackets on the market weighing in at 2lbs. Tandem riding with your buddies is now easy as pie with your snowboards on the rack and not in your back packs hitting you in the back of the head. Having snowboards fastened to the snowmobile allows you to negotiate tricky snowmobiling situations getting to your favorite big mountain line or jump spot.

�e Metal Snowboard Rack system is made for the minimalist who wants to be able to carry his or her snowboard and nothing else. �e CFR Metal Snowboard Rack System carries one snowboard on the side of your snowmobile. (No other rack required)

Another Metal Snowboard Rack System can be purchased to carry two snowboards. �e CFR Top mount Billet bracket (Sold separately) can be purchased if you need to mount the bracket to the top tunnel of your snowmobile.

Features:-Used by Professional Snowboarders Eric Jackson, Bjorn Leines and Mads Johnson to get there snowboards into the backcountry.-Metal Snowboard Rack System carries one snowboard on the side of most snowmobiles (No other rack required) -Another snowboard can be carried by purchasing another Metal Snowboard Rack Systems.-A cost e�ective way of carrying a snowboard on your snowmobile.-Billet Aluminum top bracket is an optional part. -Some snowmobile requires bracket to be mounted to the top of the rear tunnel.-Light weight Nylon parts are infused with resin that makes them extremely strong and can handle -100 degree cold temps.-Custom made Injected molded straps that can handle temps as low as -100 cold but will break in severe roll overs to prevent damage.-Ratchets and Ladders are custom made for superior ratcheting lock down.-All mounting Hardware included is made from high grade stainless steel. (Super strong and rust Free)

Part# M01

Photo: Mason Mashon

13

Metal Ski Bracket System (DTM)Part# M02

Photo: Blake JorgensonSledskiers: Mark Abma and friend.

�e CFR Metal Ski Bracket System is one of the lightest snowmobile ski racks available today at 5lbs. �is is the minimalist set up for a person who only wants to carry one ski and pole on each side of there snowmobile.

Having skis fastened to the snowmobile allows you to negotiate tricky snowmobiling situations getting to your favorite backcountry recreating area.

Features:-Metal Ski Bracket System carries one ski and pole on each side of most snowmobiles. (No other rack required.)-A cost e�ective way of carrying a pair of skis and poles on your snowmobile-Light weight Nylon parts are made from extremely strong infused resin that can handle-100 degree cold temps-Custom made Injected molded straps that will not break in -100 degree cold but will break in severe roll overs to prevent damage.-Ratchets and Ladders are custom made for superior ratcheting lock down-All mounting Hardware included is made from high grade stainless steel. -Super strong and rust free-Weight: 5 lb

14

Boondocker

�e CFR Boondocker handlebar, Dan Treadway handlebar and Knucks risers are now one of the Industry leaders in a�ermarket handlebars and risers for snowmobiles. Last year’s Boondocker and Dan Treadway handlebar changed handlebar design and increased the performance of snowmobiling. �is year we added the Boondocker 2.0, Treadway 2.0 and Turcotte to our handlebar line up. We added 1.5” of width on each bar to allow a more comfortable and stable position when snowmobiling. �e added width will also allow some stock controls to be attached to the handlebars directly along with more brake lever space. Our entire line up of handlebars are built from the inside out. We start with high quality 7075 double butted heat treated aluminum for a strong and lightweight base. In the center, where the risers stem clamps to the bar, the width is a beefy 1 1/8” thick. �e handlebars then taper o� to 7/8” thick for all of your handlebar controls and hands to �t nicely around. �is construction also allows energy to dissipate over a gradual tapering thickness within the inner core. �is results in a stronger bar that dampens hard hits and also gives the user a better feel of what’s going on underneath on the snow.

Flat Black Part# CD01

Monster Green Part# CD02

Ghost White Part# CD03Specs

-30” Width-2” Rise, 7 Degree Up, 12 Degree Back 30 degree Back.-Made from 7075 Heat treated super aluminum with Flex technology.-Strong, Lightweight and tough as shit.-Better positioning than stock bars and way stronger!-Cutting edge design dissipates bumpy conditions better than stock bars keeping you fresh and riding longer.-Vertical and horizontal positioning graphics for the most accurate center and pull back angulation.-CFR Bar pad included!

Photo: Russell DalbyRider: Mark Sollors

Snowmobile Control Division

15

Boondocker 2.0

Specs

-31.5” width-2” Rise, 7 degree Up, 12 degree Back.-Strong, Lightweight and tough as shit!-�e Bars bends and construction dissipate bumpy access roads and keep you less fatigued so you ride better, and most importantly, longer.-Vertical and horizontal positioning graphics allows for easy installation without needing a tape measure! -CFR Bar pad included.

Flat Black Part# CD01.5

Ghost White Part# CD03.5

Hot Pink Part# CD12

Photo: Tim Grey

16

Brett Turcotte Signature bar

Specs

-31.5” width-2” Rise, 7 degree Up, 12 degree Back.-Strong, Lightweight and tough as shit!-�e Bars bends and construction dissipate bumpy access roads and keep you less fatigued so you ride better, and most importantly, longer.-vertical and horizontal positioning graphics allows for easy installation without needing a tape measure! -CFR Bar pad included.

�e Brett Turcotte signature bar is the handlebar of choice for Brett and his mind blowing snowmobiling skills. From the Snowcross Track to the backcountry, Brett is the Jedi and this Handlebar his sword! Brett Chose the Boondocker handlebar, picked the color and designed the graphics for this bar. Available in Green Only!

Rider - Brett TurcottePhoto - Julie-Ann Chapman

Rider - Brett TurcottePhoto - Tim Grey

Brett Turcotte Signature Part# CD13

17

Dan Treadway Signature Bar

Specs

-30” width-3” Rise, 8 degree Up, 14 degree Back-Strong, Lightweight and tough as shit!-�e Bars bends and construction dissipate bumpy access roads and keep you less fatigued so you ride better ,and most importantly, longer.-Vertical and horizontal positioning graphics allows for easy installation without needing a tape measure! -CFR Bar pad included.

Flat Black Part# CD04

Monster green Part# CD05

Ghost White Part# CD06

Dan changed what was thought possible on a snowmobile. �e only thing that was holding himback was his equipment. �is Barwas the result of what Dan wasmissing from his stock and othera�ermarket bars. �e Bends wereall Dans specs along with the colors and graphics.

Photo: Bryn HughesSnowmobiler: Dan Treadway

Photo: Russell DalbySnowmobiler: Dan Treadway

18

Dan Treadway 2.0 Bar

Specs

-31.5” width-3” Rise, 8 degree Up, 14 degree Back-Strong, Lightweight and tough as shit!-�e Bars bends and construction dissipate bumpy access roads and keep you less fatigued so you ride better, and most importantly, longer.-Vertical and horizontal positioning graphics allows for easy installation without needing a tape measure! -CFR Bar pad included.

Flat Black Part# CD04.5

Monster green Part# CD05.5

Ghost White Part# CD06.5

Dan continues to push the sport ofsnowmobiling in the mountains year a�er year. His signature bar re�ects his all-around snowmobiling just given er style! Working with Dan’s Feedback last year we decided to Release the Treadway 2.0. �e added 1.5”width gives you stability on snow, in the air, and gives you more space on the handlebars for controls and brake lever positioning.

Photo: Bryn HughesSnowmobiler: Dan Treadway

Photo: Russell DalbySnowmobiler: Dan Treadway

19

Knucks Handlebar risers are ideal to personally customise the height of your bars. Machined from Hi Strength super tough 6061 - T06 Aluminum they can take anything you can throw at them. An anodized black tumble �nish and Graphics kit will ad some style to your steed. �e graphics are not just for looks with a centering line on the top cap allowing you to adjust your handle bars to where you want them! �e Knucks come in 4,5,6,7 and 8 inch heights and will work on your 7/8" or over sized 1 1/8" bars.

Part# 4" CD075" CD086" CD097" CD108" CD11

Features:-CNC machined from Hi strength 6061 - T06 Aluminum-Graphics are laser etched for a durable long lasting look-Anodized black and tumbled �nished-Available in 4,5,6,7 and 8" inch heights-Will work with either 1-1/8" tapered bar or 7/8"bars. (Adaptor included.-Patent pending ⅞" anti slip insert keeps bars where you want them-You must have a pivot style steering post or a double pivot adapter-Designed to be used with the new CFR Boondocker/DT Bars but will work with all handlebars-Double check length of cables and brake lines for a proper �t. Extended length cables or brake lines may be required for proper operation

Knucks Risers

Rider - Rob Alford

20

New for 2014-2015 from CFR are sled wraps. Sled wraps not only ad style to your whip but also protect the plastic from the abusive sport of snowmobiling. �e graphics are a real hand drawn topo graphical map of one of our favorite snowmobiling areas just west of our headquarters here in Pemberton BC Canada. CFR is working with Toyskinz to produce these wraps witch are made of industry leading 6 mil. vinyl and 15 mil.over-laminate, making a total of 21 mil. thick. �e Colors and designs of the wraps work well with all of our other snowmobile accessories for a tight look!

Wraps

Ski-doo

Polaris

Arctic Cat

Yamaha

Part#WSD01 White

Part#WSD02 Pink

Part#WSD03 Red

Part#WSD04 Black

Part# AC01 Green

Part# AC02 White

Part# AC03Pink

Part# AC04 Black

Part# WY01 Green

Part# WY02 Blue

Part# WY03 Red

Part# WY04 Black

Part# WP01Red

Part# WP02 White

Part# WP03Pink

Part# WP04 Black

21

�e CFR Connect System enables you to take your CFR iRack on or o� at whim! Four stainless steel buckles lock your rack down to your snowmobile. Permanent Mounting points on snowmobile are low pro�le stainless steel loops. Go lightweight and low pro. Drop the rack and go. *CFR Connect system only works with the CFR iRacks and on Ski Doo XP/XM model snowmobiles with a 146" tunnel or longer.

Photo: West Coast SleddersSnowmobiler: Tom Cepek

Connect SystemPart# C01

22

Ad a little more Metal to your Ski Doo XP/XM. �e CFR Blades are designed to be fastened to the outside or inside of the rear tunnel of your 146”, 154", 163 or 174 tunnel. �e added 50% more strength allows more weight to be carried on the tunnel. �e CFR Blades are recommended if you travel on bumpy roads carrying lots of extra weight on your snowmobile.

Features- Anatomically designed to �t the rear tunnel of the Ski Doo XP/XM.- Comes in 146”, 154” , 163”and 174" lengths.- Mount them on the inside of your tunnel for the stock look.- Mount them on the outside for the check me out I’m awesome look.- Come complete with 1 right/1 le� side.- All Rivets and mounting hardware included.

Part# TS01 -146” Track lengthPart# TS02 -154” Track lengthPart# TS03 -163” Track lengthPart# TS07 -174” Track length.

Nytro Blades square o� the rear rounded tunnel leaving a �at platform to mount CFR tunnel racks.

Part# TS04 2010-2013 Yamaha Nytro.Part# TS05 2008-2009 Yamaha Nytro.

06-08 Arctic Cat Blades go on dimples that are on top of rear tunnel allowing a �at surface for rack to sit on.

Part# TS06 2008-2009 Arctic Cat Photo: Bryn HughesTandemers: Dan Treadway Logan Pehota

Blades

23

Part# 1001

Part# 1002

�e CFR Aluminum Ratchet is custom made to take the abuse that snowmobiling throws at it.

�ese custom made ratchets are designed to hold your snowboard and or skis down solid until you need them no matter what!. �e powder coated black �nish will keep them rust free and looking good. �e thick springs are long lasting and will give you years of trouble free use.-�is Ratchet will replace all CFR ratchets current and past years.

�e CFR 220MM Replacement Ladder Strap works on all of our Snowboard and Ski Brackets.-64 Stainless Steele rivet and two washers included.

8" Replacement Strap�e CFR 8” replacement strap is used in most of the snowboard and ski rack carrying racks that we manufacture. A 66 Stainless steel rivet and two washers included.

16" Replacement Strap�e CFR 16” replacement strap is used in all of the snowboard and ski rack carrying racks that we manufacture. A 64 Stainless steel rivet and washer included.

Aluminium Rachet

Ladder Strap

Replacment Strap

Photo: Phil TifoSnowmobiler: Dan Treadway

Part# 1006

Part# 1003

Spare Parts

24

�e CFR Snow Scraper is a great way to scrape o� unwanted snow and ice from your running boards, Snowboards or Skis.In the shop you can scrape o� the fresh hot wax from your Skis or Snowboards.

�e CFR Tunnel armour use super sticky 3m adhesive to add a layer of protection to your snowmobile. Stick the pad on the tunnel to prevent against rubbing from equipment.

�e CFR bar pads are designed to �t all CFR Handlebars or any oversized large diameter Handlebars. �e Dual density foam will protect against sharp corners and hardware on riser. �e Cordura material with CFR logos is long lasting and can withstand cold temps and all of the abuse that comes with snowmobiling. �e CFR Bar pad comes in Black with white logos.

�e must have strap for your backcountry adventures, the CFR Super Strap and duct tape can pretty much �x anything.

�e CFR Snow Scratchers are a cost e�ective way to prevent the overheating of your snowmobiles Motor on those early morning long approaches.

�ese Scratchers are bad ass. �ey kick up twice as much snow as regular Scratchers and wont break or bend if you accidentally go in reverse. Hanger Included to secure scratchers when not in use.

Scraper

Tunner Armour

Bar Pad

Super Straps

Snow Scratchers

Reversible Snow Scratchers

Part# 1012

Part# 1014

Part# CD12

Part# 1013

Part# S01

Part# S02

Accessories

25

2014/2015Snowmobile Racks

and Accessories

For more info or ordering please visit cheetahfactoryracing.com or call (604)-894-18801-877-894-1880

Studio Photo:Dice K.Brian HockensteinBrochure:Barrett Hepburn

Studio Photo:Dice K.Brian HockensteinBrochure:Barrett HepburnPhoto:dbPhoto:db