Upload
kenneth-amen
View
111
Download
3
Embed Size (px)
DESCRIPTION
ECAD Amplifier
Citation preview
Adamson UniversityCollege of Engineering
Electronics and Communications Engineering Department
Class B and AB Amplifiers
Engr. Bernadeth B. ZariInstructor
ECAD Class B and Class AB Amplifiers 1
CLASS B AND CLASS AB PUSH-PULL AMPLIFIERS
When an amplifier is biased at cut-off so that it operates in the linear region for 180° of the input cycle and is in cut-off for 180°, its is classified as Class B amplifier.
Class AB amplifiers are biased to conduct for slightly more than 180°.
The primary advantage of a class B or class AB amplifier over a class A amplifier is that either one is more efficient than a class A amplifier. You can get more output power for a given amount of input power.
A disadvantage of class B or class AB amplifier is that it is more difficult to implement the circuit in order to get a linear reproduction of the input waveform.
Class B Operation
Class B operation is provided when the dc bias leaves the transistor biased just off, the transistor turning on when the ac signal is applied. This is essentially no bias, and the transistor conducts current for only one-half of the signal cycle.
The Q-Point Is at Cut-off
The class B amplifier is biased at the cutoff point so that ICQ
= 0 and VCEQ = VCE (cutoff). It is brought out of cutoff and operates
ECAD Class B and Class AB Amplifiers 2
in its linear region when the input signal drives the transistor into conduction.
Fig. 9 – 7 Common collector class B amplifier
Class B Push-Pull Operation
The circuit in Figure 9-7 only conducts for the positive of the cycle. To amplify the entire cycle, it is necessary to add a second class B amplifier that operates the negative half of the cycle. The combination of two class B amplifiers working together is called push-pull operation.
Fig. 9 – 8 Block representation of push – pull operation
ECAD Class B and Class AB Amplifiers 3
Input (DC) Power
The power supplied to the load by an amplifier is drawn form the power supply (or power supplies) that provide the input or dc power. The amount of this input power can be calculated using
where Idc is the average or dc current drawn from the power supplies. In class B operation, the current drawn from a single power supply has the form of a full-wave rectified signal, whereas that drawn from two power supplies has the form a half-wave rectified signal from each supply. In either case, the value of the average current drawn can be expressed as
Where I(p) is the peak value of the output current waveform. Using equation in the power input equation results in
Output (AC) Power
The power to delivered to the load (usually referred to as a resistance RL) can be calculated using any one of a number of equations. If one is using an rms meter to measure the voltage across the load, the output power can be calculated as
If one is using an oscilloscope, the measured peak or peak-to-peak output voltage can be used:
ECAD Class B and Class AB Amplifiers 4
The larger the rms or peak output voltage, the larger is the power delivered to the load.
Efficiency
The efficiency of the class B amplifier can be calculated using the basic equation
Using equations in the efficiency equation above results in
[Using I(p)=VL(p)/RL]. Equation shows that the larger the peak voltage, the higher is the circuit efficiency, up to a maximum value when VL (p) =VCC, this maximum efficiency then being
ECAD Class B and Class AB Amplifiers 5
Power Dissipated by Output Transistors
The power dissipated (as heat) by the output power transistors is the difference between the input power delivered by the supplies and the output power delivered to the load,
Where P2Q is the power dissipated by the two output power transistor. The dissipated power handled by each transistor is then
Example: For a class B amplifier providing a 20-V peak signal to a 16-Ω load (speaker) and a power supply of Vcc= 30V, determine the input power, output power, and circuit efficiency.Solution: A 20-V peak signal across a 16-Ω load provides a peak load current of
The dc value of the current drawn from the power supply is then
And the input power delivered by the power supply voltage is
The output power delivered to the load is
For a resulting efficiency of
ECAD Class B and Class AB Amplifiers 6
Maximum Power Considerations
For class b operation, the maximum output power is delivered to the load when VL(p)=VCC:
The corresponding peak ac current I(p)is then
So that the maximum value of average current from the power supply is
Using this current to calculate the maximum value of input power results in
The maximum circuit efficiency for class B operation is then
When the input signal results in less than the maximum output signal swing, the circuit efficiency is less than 78.5%.
ECAD Class B and Class AB Amplifiers 7
For class B operation, the maximum power dissipated by the output transistors does not occur at the maximum power input or output condition. The maximum power dissipated by the two output transistor occur when the output voltage across the load is
For a maximum transistor power dissipated of
Example: For a class B amplifier using a supply of VCC= 30V and driving a load of 16Ω, determine the maximum input power, output power, and transistor dissipation.
Solution: The maximum output power is
The maximum input power drawn from the voltage supply is
The circuit efficiency is then
As expected. The maximum power dissipated by each transistor is
ECAD Class B and Class AB Amplifiers 8
Under maximum conditions a pair of transistors each handling 5.7 W at most can deliver 28.125W to a 16Ω load while drawing 35.81W from the supply.
The maximum efficiency of a class B amplifier can also be expressed as follows:
So that
Example: Calculate the efficiency of a class B amplifier for a supply voltage of VCC = 24V with peak output voltages of:
a. VL(p)= 22V.b. VL(p)= 6V.
Solution: Using equations gives
ECAD Class B and Class AB Amplifiers 9
a.
b.
Notice that a voltage near the maximum [22 V in part (a)] results in an efficiency near the maximum, where as a small voltage swing [6 V in part (b)] still provides an efficiency near 20%. Similar power supply and signal swings would have resulted in much poorer efficiency in class A amplifier.
CLASS B AMPLIFIER CIRCUIT
There are two approaches for using push-pull amplifiers to reproduce the entire waveform. The first approach uses transformer coupling. The second uses two complementary symmetry transistors; these are a matching pair of npn / pnp BJT’s or a matching pair of n-channel/p-channel FET’s.
Transformer Coupling
Transformer coupling is illustrated in Figure 9-9. The input transformer has a center-tapped secondary that is connected to ground, producing phase inversion of one side with respect to the other.
The input transformer thus converts the input signal to two out-of-phase signals for the transistors. Notice that both transistors are npn types.
ECAD Class B and Class AB Amplifiers 10
Q1 will conduct on the positive part of the cycle and Q2 will conduct on the negative part.
Fig. 9 – 9 Transformer coupled push-pull amplifier, Q1 conducts during the positive half-cycle; Q2 conducts during the negative half cycle. The two halves are combined by the output transformer
Complimentary Symmetry Transistors
Figure 9-10 shows one of the most popular types of push-pull class B amplifiers using two emitter-followers and both positive and negative power supplies. This is a complementary amplifier because one emitter-follower uses an npn transistor and the other a pnp, which conduct on opposite alternations of the input cycle.
ECAD Class B and Class AB Amplifiers 11
(a) During a positive half cycle
(b) During a negative half cycle
Fig.9 – 10 push-pull ac operation
Crossover Distortion
When the dc base voltage is zero, both transistors are off and the input signal voltage must exceed VBE before a transistor conducts. Because of this, there is a time interval between the positive and negative alternations of the input when neither
ECAD Class B and Class AB Amplifiers 12
transistor is conducting, as shown in Figure 9-11. The resulting distortion in the output waveform is called crossover distortion.
Biasing the Push-Pull Amplifier for Class AB Operation
To overcome crossover distortion, the biasing is adjusted to just overcome VBE of the transistors; this result in a modified form of operation called class AB.
In class AB operation, the push-pull stages are biased into slight conduction, even when no input signal is present. This can be done with a voltage divider and diode arrangement, as shown in Figure 9-12.
Fig. 9 – 12 biasing the push pull amplifier to eliminate crossover distortion
When the diode characteristics of D1 and D2 are closely matched to the characteristics of the transistor base-emitter junctions, the current in the diodes and the current in the
ECAD Class B and Class AB Amplifiers 13
transistors are the same; this is called a current mirror. This current mirror produces the desired class AB operation and eliminates crossover distortion.
Assuming that both transistors are identical, the drop across D1 equals the VBE of Q2. Since they are matched, the diode current will be the same as ICQ. The diode current and ICQ can be found by applying Ohm’s Law to either R1 or R2 as follows:
AC Operation
Consider the ac load line for Q1 of the class AB amplifier in Figure 9-12. It’s Q-point slightly above cutoff. The ac cutoff voltage for a two-supply operation is at VCC with an ICQ as given earlier. The ac saturation current for a two-supply operation with a push-pull amplifier is:
Example: Determine the ideal maximum out voltage and current for the circuit.
ECAD Class B and Class AB Amplifiers 14
Solution: The ideal maximum peak output voltage is Vout(peak) VCEQ = VCC = 20 V
The ideal maximum peak current is Iout(peak) ICsat = RL = 20 V/16 Ω = 1.25 A
Single-Supply Push-Pull Amplifier
Push-pull amplifiers using complimentary symmetry transistors can be operated from a single voltage source as shown in Figure 9-16. The circuit operation is the same as that described previously, except the bias is set to force the output emitter voltage to be VCC/2 instead of zero volts used with two supplies.
ECAD Class B and Class AB Amplifiers 15
Fig. 9 – 13 Single ended push-pull amplifier
AMPLIFIER DISTORTION
A pure sinusoidal signal has a single frequency at which the voltage varies positive and negative by equal amounts. Any signal varying over less than 360° cycle is considered to have distortion. When distortion occurs, the output will not be an exact duplicate (except for magnitude) of the input signal.
Distortion can occur because the device characteristic is not linear, in which case non-linear amplitude distortion occurs. This can occur with all classes of amplifier operation. Distortion
ECAD Class B and Class AB Amplifiers 16
can also occur because the circuit elements and devices respond to the input signal differently at various frequencies, this being frequency distortion. One technique for describing distorted but period waveforms uses Fourier analysis, a method that describes any periodic waveform in terms of its fundamental frequency component and frequency components at integer multiples – these components are called harmonic components or harmonics.
Example:
A signal that is originally 1000 Hz could result, after distortion, in a frequency component at 1000 Hz (1 kHz) and harmonic components at 2 kHz, 3 kHz, 4 kHz, and so on.
The original frequency of 1 kHz is called the fundamental frequency; those at integer multiples are the harmonics.
The 2 kHz component is therefore called a second harmonic.
The 3 kHz is the third harmonic, and so on. The fundamental frequency is not considered a harmonic.
Fourier analysis does not allow for fractional harmonic frequencies – only integer multiples of the fundamental.
HARMONIC DISTORTION
A signal is considered have harmonic distortion where there are harmonic frequency has an amplitude A1 and the nth frequency component has an amplitude An, a harmonic distortion can be defined as
ECAD Class B and Class AB Amplifiers 17
The fundamental component is typically larger than any harmonic component.
Example: Calculate the harmonic distortion components for an output signal having fundamental amplitude of 2.5V, second harmonic amplitude of 0.25V, third harmonic amplitude of 0.1V, and fourth harmonic amplitude of 0.05V.
Solution: Using Eq. yields:
Total Harmonic Distortion
When an output signal has a number of individual harmonic distortion components, the signal can be seen to have a total harmonic distortion based on the individual elements as combined by the relationship of the following equation:
X 100%
Example: Calculate the total harmonic distortion for the amplitude components given in Example 12.13.
ECAD Class B and Class AB Amplifiers 18
Solution: using the computed values of D2 = 0.10, D3 = 0.04 and D4 = 0.02 in eq., we obtain:
X 100%
Second Harmonic Distortion
Figure 12.20 shows a waveform to use for obtaining second harmonic distortion. A collector current waveform is shown with the quiescent, minimum, and maximum signal levels, and the time at which they occur is marked on the waveform. The signal shown indicates that some distortion is present. An equation that approximately describes the distorted signal waveform is:
The current waveform contains the original quiescent current ICQ
which occurs with zero input signal; an additional current Io due to the non zero average of the distorted signal; I2, at twice the fundamental frequency. Although other harmonics are also present, only the second is considered here. Equating the resulting current at a few points in the cycle to that shown on the current waveform provides the following three relations:
At point 1 (t = 0)
ECAD Class B and Class AB Amplifiers 19
At point 2 (t = ),
At point 3 (t = ),
Solving the preceding three equations simultaneously gives the following results
Referring to equation, we can express the definition of second harmonic distortion as
Inserting the values of I1 and I2 determined above gives
In a similar manner, the second harmonic distortion can be expressed in terms of measured collector-emitter voltages:
ECAD Class B and Class AB Amplifiers 20
Example: Calculate the second harmonic distortion if an output waveform displayed on an oscilloscope provides the following measurements:
a. VCEmin = 1V, VCEmax = 22V, VCEQ = 12V.b. VCEmin = 4V, VCEmax = 20V, VCEQ = 12V.
Solutions:
a.
b.
Power of a Signal Having Distortion
When distortion does occur, the output power calculated for the undistorted signal is no longer correct. When distortion is present, the output power delivered to the load resistor RC due to the fundamental component of distorted signal is
The total power due to all the harmonic components of the distorted signal can then be calculated using
The total power can also be expressed in terms of the total harmonic distortion,
ECAD Class B and Class AB Amplifiers 21
Example: For a harmonic distortion reading of D2 = 0.1, D3 = 0.02, and D4 = 0.01, with I1 = 4A and RC = 8Ω, calculate the total harmonic distortion, fundamental power component, and total power.
Solution: The total harmonic distortion is
The fundamental power calculated using the equations is then
The total power calculated using the equation is then
(Note that the total power is due mainly to the fundamental component even with 10% second harmonic distortion.)
ECAD Class B and Class AB Amplifiers 22