CLD-DS102 Rev 0 cree Xlamp mh-B leds - Mouser Electronics · CLD-DS102 Rev 0 Product family data sheet ... C4 475 538 65F MHBAWT-0000- ... XLAMP ® MH-B LeDS copyright 2010 cree,

CLD

-DS

102 R

ev

0

Product family data sheet

cree® Xlamp® mh-B leds

WW

W.C

Ree

.CO

M/X

LAM

P

Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.

Product descriPtion

The XLamp® MH-B LeD is a new generation of high-power LeD that delivers a more effective way to achieve low-cost systems than mid-power (MP) LeDs. Built using Cree’s high-reliability ceramic-package technology, the XLamp MH-B LeD is able to operate at higher temperatures than MP LeDs with no reduction in rated lifetime, enabling an impressive 60% reduction in heat sink size and cost. Using up to 26 times fewer LeDs than MP LeDs to achieve the same performance, the XLamp MH-B LeD is optimized to simplify LeD system designs for directional and semi-directional applications.

features

• Maximum drive current: 175 mA• Low thermal resistance:

5.5 °C/W• Maximum junction temperature:

150 °C• viewing angle: 115°• Available in 80-CRI minimum

warm white and 90-CRI minimum warm white

• ANSI-compatible chromaticity bins

• Unlimitedfloorlifeat≤30ºC/85%RH

• Reflowsolderable-JEDECJ-STD-020C

• electrically neutral thermal path• UL-recognized component (E349212)

Cree, Inc.4600SiliconDriveDurham,NC27703

USATel:+1.919.313.5300

Copyright©2014Cree,Inc.Allrightsreserved.Theinformationinthisdocumentissubjecttochangewithoutnotice.Cree®, the Cree logo, XLamp® and easyWhite® are registered trademarks of Cree, Inc.

Cree, Inc.4600SiliconDriveDurham,NC27703

USATel:+1.919.313.5300

taBle of contents

Characteristics ..............................2Flux Characteristics, easyWhite® Order Codes and Bins ....................3Flux Characteristics, ANSI White Order Codes and Bins ....................4Relative Spectral Power Distribution .4RelativeFluxvs.JunctionTemperature .................................5electrical Characteristics .................5Relative Flux vs. Current ................6Relative Chromaticity vs. Current .....6Relative Chromaticity vs. Temperature .................................7Typical Spatial Distribution ..............7Thermal Design .............................8Performance Groups - Brightness .....8Performance Groups - Chromaticity ..9Cree easyWhite® Bins Plotted on the1931CIEColorSpace .............10Cree ANSI White Bins Plotted on the1931CIEColorSpace .............11Bin and Order Code Formats .........11ReflowSolderingCharacteristics ....12Notes .........................................13Mechanical Dimensions.................14Tape and Reel .............................15Packaging ...................................16

http://WWW.CREE.COM/XLAMP

xlamp® mH-B leds


2

Copyright © 2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo, XLamp® and EasyWhite® are registered trademarks of Cree, Inc.

2

characteristics

characteristics unit minimum typical maximum

Thermal resistance, junction to solder point °C/W 5.5

viewing angle (FWHM) degrees 115

Temperaturecoefficientofvoltage mv/°C -16

ESDwithstandvoltage(HBMperMil-Std-883D) v 8000

DC forward current mA 120 175

Reverse current mA 0.1

Forward voltage (@ 120 mA, 85 °C) v 37

Forward voltage (@ 120 mA, 25 °C) v 42

LeD junction temperature °C 150

xlamp® mH-B leds


3


3

fluX characteristics, easyWhite® order codes and Bins (tJ = 85 °c)

The following tables provide order codes for XLamp MH-B LeDs. For a complete description of the order code nomenclature, please reference Bin and Order Code Formats (page 11).

cct range

criBase order codes

min. luminous flux @ 120 ma

2-step order code 4-step order code 5-step order code

min Groupflux

(lm) @ 85 °c

flux (lm) @ 25 °c*

chromaticity region

chromaticity region

chromaticity region

6500 K 80C4 475 538

65F

MHBAWT-0000-000N0HC465F

D2 510 577 MHBAWT-0000-000N0HD265F

5700 K 80C4 475 538

57F


D2 510 577 MHBAWT-0000-000N0HD257F

5000 K 80C4 475 538

50F


D2 510 577 MHBAWT-0000-000N0HD250F

4000K 80C4 475 538

40H

MHBAWT-0000-000N0HC440H

40F


40E

MHBAWT-0000-000N0HC440E

D2 510 577 MHBAWT-0000-000N0HD240H

MHBAWT-0000-000N0HD240F

MHBAWT-0000-000N0HD240E

3500K 80C4 475 538

35H


35F


35E


D2 510 577 MHBAWT-0000-000N0HD235H

MHBAWT-0000-000N0HD235F

MHBAWT-0000-000N0HD235E

3000K

80C2 440 498

30H


30F


30E


C4 475 538 MHBAWT-0000-000N0HC430H



90A2 330 374

30H

MHBAWT-0000-000N0UA230H

30F

MHBAWT-0000-000N0UA230F

30E

MHBAWT-0000-000N0UA230E

A4 355 402 MHBAWT-0000-000N0UA430H



2700 K

80C2 440 498

27H


27F


27e

MHBAWT-0000-000N0HC227e

C4 475 538 MHBAWT-0000-000N0HC427H



90A2 330 374

27H

MHBAWT-0000-000N0UA227H

27F


27e

MHBAWT-0000-000N0UA227e

A4 355 402 MHBAWT-0000-000N0UA427H



Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy)

measurements and a tolerance of ±2 on CRI measurements.* Flux values @ 25 °C are calculated and for reference only.

xlamp® mH-B leds


4


4

fluX characteristics, ansi White order codes and Bins (tJ = 85 °c)

cct range

criBase order codes

min. luminous flux @ 120 ma chromaticity regions order code

min typ Group flux (lm) @ 85 °c

flux (lm) @ 25 °c*

6500 K 80 ---C4 475 538

1A0, 1B0, 1C0, 1D0MHBAWT-0000-000N0HC40E1

D2 510 577 MHBAWT-0000-000N0HD20e1

5700 K 80 ---C4 475 538

2A0, 2B0, 2C0, 2D0MHBAWT-0000-000N0HC40E2

D2 510 577 MHBAWT-0000-000N0HD20e2

5000 K 80 ---C4 475 538

3A0,3B0,3C0,3D0MHBAWT-0000-000N0HC40E3

D2 510 577 MHBAWT-0000-000N0HD20E3

Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy)

measurements and a tolerance of ±2 on CRI measurements.* Flux values @ 25 °C are calculated and for reference only.

relative sPectral PoWer distriBution

Relative Spectral Power Distribution

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

380 430 480 530 580 630 680 730 780

Rel

ativ

e S

pect

ral

Pow

er

Wavelength (nm)

Cool White

Neutral White

Warm White

xlamp® mH-B leds


5


5

relative fluX vs. Junction temPerature (if = 120 ma)

electrical characteristics (tJ = 85 °c)

Relative Flux Output vs. Junction Temperature

0%

20%

40%

60%

80%

100%

120%

25 50 75 100 125 150

Rel

ativ

e Lu

min

ous

Flu

x

Junction Temperature (ºC)

Electrical Characteristics (Tj = 85ºC)

0

25

50

75

100

125

150

175

32 33 34 35 36 37 38 39

Forw

ard

Cu

rren

t (m

A)

Forward Voltage (V)

xlamp® mH-B leds


6


6

relative fluX vs. current (tJ = 85 °c)

relative chromaticity vs. current (Warm White)

Relative Intensity vs. Current (Tj = 85ºC)

0%

20%

40%

60%

80%

100%

120%

140%

0 25 50 75 100 125 150 175

Rel

ativ

e Lu

min

ous

Flu

x

Forward Current (mA)

-0.015

-0.010

-0.005

0.000

0.005

0.010

25 50 75 100 125 150 175

Current (mA)

ΔCCx

ΔCCy

xlamp® mH-B leds


7


7

relative chromaticity vs. temPerature (Warm White)

tyPical sPatial distriBution

-0.015

-0.010

-0.005

0.000

0.005

0.010

25 50 75 100 125 150

Tj (°C)

ΔCCx

ΔCCy

Far Field

0%

20%

40%

60%

80%

100%

-90 -70 -50 -30 -10 10 30 50 70 90

Rel

ativ

e Lu

min

ous

Inte

nsi

ty

Angle (º)

xlamp® mH-B leds


8


8

thermal desiGn

The maximum forward current is determined by the thermal resistance between the LeD junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics.

Performance GrouPs - BriGhtness (tJ = 85 °c)

XLampMH-BLEDsaretestedforluminousfluxandplacedintooneofthefollowingbins.

Group code min. luminous flux max. luminous flux

94 308 330

A2 330 355

A4 355 380

B2 380 410

B4 410 440

C2 440 475

C4 475 510

D2 510 550

D4 550 590

Thermal Design

0

25

50

75

100

125

150

175

200

0 20 40 60 80 100 120 140

Max

imu

m C

urr

ent

(mA

)

Ambient Temperature (ºC)

Rj-a = 7 °C/W Rj-a = 10 °C/W Rj-a = 15 °C/W Rj-a = 20 °C/W

xlamp® mH-B leds


9


9

Performance GrouPs - chromaticity (tJ = 85 °c)

XLampMH-BLEDsaretestedforchromaticityandplacedintooneoftheregionsdefinedbythefollowingboundingcoordinates.

easyWhite color temperatures – 5-step

cctcenter Point major axis minor axis rotation

angle (°)x y a b

4000K 0.3825 0.3799 0.0157 0.0067 53.72

3500K 0.4081 0.3917 0.0155 0.0069 53.22

3000K 0.4343 0.4029 0.0139 0.0068 53.22

2700 K 0.4583 0.4100 0.0135 0.0070 53.70


code cct x y

65F 6500 K

0.3097 0.3196

0.3079 0.3297

0.3164 0.3382

0.3176 0.3275

57F 5700 K

0.3253 0.3325

0.3249 0.3439

0.3331 0.3514

0.3330 0.3393

50F 5000 K

0.3407 0.3459

0.3415 0.3586

0.3499 0.3654

0.3484 0.3521

40F 4000K

0.3744 0.3685

0.3782 0.3837

0.3912 0.3917

0.3863 0.3758

35F 3500K

0.3981 0.3800

0.4040 0.3966

0.4186 0.4037

0.4116 0.3865

30F 3000K

0.4242 0.3919

0.4322 0.4096

0.4449 0.4141

0.4359 0.3960

27F 2700 K

0.4475 0.3994

0.4573 0.4178

0.4695 0.4207

0.4589 0.4021


code cct x y

40H 4000K

0.3784 0.3741

0.3804 0.3818

0.3867 0.3857

0.3844 0.3778

35H 3500K

0.4030 0.3857

0.4061 0.3941

0.4132 0.3976

0.4099 0.3890

30H 3000K

0.4291 0.3973

0.4333 0.4062

0.4395 0.4084

0.4351 0.3994

27H 2700 K

0.4528 0.4046

0.4578 0.4138

0.4638 0.4152

0.4586 0.4060

xlamp® mH-B leds


10


10

Performance GrouPs - chromaticity (tJ = 85 °c) - continued

cree easyWhite® Bins Plotted on the 1931 cie color sPace (tJ = 85 °c)

ansi White Bins

code cct Bin code x y

0e1 6500 K

1A0

0.3048 0.3207

0.3130 0.3290

0.3144 0.3186

0.3068 0.3113

1B0

0.3028 0.3304

0.3115 0.3391

0.3130 0.3290

0.3048 0.3207

1C0

0.3115 0.3391

0.3205 0.3481

0.3213 0.3373

0.3130 0.3290

1D0

0.3130 0.3290

0.3213 0.3373

0.3221 0.3261

0.3144 0.3186

ansi White Bins


0e2 5700 K

2A0

0.3215 0.3350

0.3290 0.3417

0.3290 0.3300

0.3222 0.3243

2B0

0.3207 0.3462

0.3290 0.3538

0.3290 0.3417

0.3215 0.3350

2C0

0.3290 0.3538

0.3376 0.3616

0.3371 0.3490

0.3290 0.3417

2D0

0.3290 0.3417

0.3371 0.3490

0.3366 0.3369

0.3290 0.3300

ansi White Bins


0E3 5000 K

3A0

.3371 .3490

.3451 .3554

.3440 .3427

.3366 .3369

3B0

.3376 .3616

.3463 .3687

.3451 .3554

.3371 .3490

3C0

.3463 .3687

.3551 .3760

.3533 .3620

.3451 .3554

3D0

.3451 .3554

.3533 .3620

.3515 .3487

.3440 .3427

2700 K 3000 K

3500 K

4000 K

4500 K 5000 K

5700 K

6350 K

7000 K

0.31

0.32

0.33

0.34

0.35

0.36

0.37

0.38

0.39

0.40

0.41

0.42

0.43

0.44

0.29

0.30

0.31

0.32

0.33

0.34

0.35

0.36

0.37

0.38

0.39

0.40

0.41

0.42

0.43

0.44

0.45

0.46

0.47

0.48

0.49

CCy

CCx

ANSI C78.377 Quadrangle

EasyWhite 5-step

EasyWhite 4-step

EasyWhite 2-step

xlamp® mH-B leds


11


11

cree ansi White Bins Plotted on the 1931 cie color sPace (tJ = 85 °c)

Bin and order code formats

Bincodesandordercodesareconfiguredasfollows.

order code Bin code

5000K

5700K

6500K

8000K

0A

0B

0C

0D

0R

0S

0T

0U

1A

1B

1C

1D

2A

2B

2C

2D

3A

3B

1R

1S

1T

1U

2R

2S

2T

2U

3R

3S

0.28

0.29

0.30

0.31

0.32

0.33

0.34

0.35

0.36

0.37

0.38

0.39

0.40

0.28

0.29

0.30

0.31

0.32

0.33

0.34

0.35

0.36

CC

y

CCx

ANSIC78.377A

E1

E23C

3D

E3

SSSCCC-HHHH-HHHGGNFFDDD

Series MHB = MH-B

Internal code

CRI Specification H = 80 min CRI U = 90 min CRI

Chromaticity region

Flux

Vf class: N0 = 36-V class

Color AWT = White

SSSCCC-WWW-FF-GGR-AAAAA

Series MHB = MH-B

Chromaticity bin

Vf class: N0 = 36-V class

Internal code

CRI Specification H = 80 min CRI U = 90 min CRI

Flux bin

Color AWT = White

xlamp® mH-B leds


12


12

refloW solderinG characteristics

Intesting,CreehasfoundXLampMH-BLEDstobecompatiblewithJEDECJ-STD-020C,usingtheparameterslistedbelow.Asageneralguideline,Creerecommendsthatusersfollowtherecommendedsolderingprofileprovidedbythemanufacturer of solder paste used.

NotethatthisgeneralguidelinemaynotapplytoallPCBdesignsandconfigurationsofreflowsolderingequipment.

Profile Feature lead-Based solder lead-free solder

Average Ramp-Up Rate (Tsmax to Tp) 3°C/secondmax. 3°C/secondmax.

Preheat: Temperature Min (Tsmin) 100 °C 150 °C

Preheat: Temperature Max (Tsmax) 150 °C 200 °C

Preheat: Time (tsmin to tsmax) 60-120 seconds 60-180 seconds

Time Maintained Above: Temperature (TL) 183°C 217 °C

Time Maintained Above: Time (tL) 60-150 seconds 60-150 seconds

Peak/ClassificationTemperature(Tp) 215 °C 260 °C

Time Within 5 °C of Actual Peak Temperature (tp) 10-30seconds 20-40seconds

Ramp-Down Rate 6 °C/second max. 6 °C/second max.

Time 25 °C to Peak Temperature 6 minutes max. 8 minutes max.

Note: All temperatures refer to the topside of the package, measured on the package body surface.

xlamp® mH-B leds


13


13

notes

lumen maintenance ProjectionsCree now uses standardized IeS LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LeD lumenmaintenance.ForinformationonthespecificLM-80datasetsavailableforthisLED,refertothepublicLM-80 results document.

Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LeD junction temperature.

moisture sensitivityIntesting,CreehasfoundXLampMH-BLEDstohaveunlimitedfloorlifeinconditions≤30ºC/85%relativehumidity(RH).Moisturetestingincludeda168-hoursoakat85ºC/85%RHfollowedby3reflowcycles,withvisualandelectricalinspections at each stage.

Cree recommends keeping XLamp LeDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LeDs to the resealable moisture-barrier bag and closing the bag immediately after use.

ul recognized componentLevel4enclosureconsideration.TheLEDpackageoraportionthereofhasbeeninvestigatedasafireandelectricalenclosure per ANSI/UL 8750.

vision advisory claimWARNING: Do not look at exposed lamp in operation. eye injury can result. For more information about LeDs and eye safety, please refer to the LeD eye Safety application note.

http://www.cree.com/~/media/Files/Cree/LED%20Components%20and%20Modules/XLamp/XLamp%20Application%20Notes/LM80_Results.pdf

http://www.cree.com/~/media/Files/Cree/LED%20Components%20and%20Modules/XLamp/XLamp%20Application%20Notes/LM80_Results.pdf

http://www.cree.com/~/media/Files/Cree/LED%20Components%20and%20Modules/XLamp/XLamp%20Application%20Notes/XLamp_lumen_maintenance.pdf

http://www.cree.com/~/media/Files/Cree/LED%20Components%20and%20Modules/XLamp/XLamp%20Application%20Notes/XLampThermalManagement.pdf

http://www.cree.com/~/media/Files/Cree/LED%20Components%20and%20Modules/XLamp/XLamp%20Application%20Notes/XLamp_EyeSafety.pdf

xlamp® mH-B leds


14


14

SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558

4600 Silicon DriveDurham, N.C 27703

UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125X° ± .5 °

UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH: 1.6

5.00

5.00

.71

0.8±.1

3.75

.45

.50

4.70

1.40

2.35

1.40

.45

.50

4.78

4.782.14

.50

.40

.50

.50.50

4.68

3.68

4.68

2.14

.40

.400 .40

.40.60 .60

1/117.000

C2610-00041

MHX OUTLINE Rev. C

05/19/14D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

RECOMMENDED PCB SOLDER PADRECOMMENDED STENCIL PATTERN

mechanical dimensions

All measurements are ± .25 mm unless otherwise indicated.

top view Bottom viewside view

recommended PcB solder Pad recommended stencil Pattern(shaded area is open)

Anode

SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558



OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5


.XX ± .25

.XXX ± .125X° ± .5 °



SURFACE FINISH: 1.6

5.00

5.00

.71

0.8±.1

3.75

.45

.50

4.70

1.40

2.35

1.40

.45

.50

4.78

4.782.14

.50

.40

.50

.50.50

4.68

3.68

4.68

2.14

.40

.400 .40

.40.60 .60

1/117.000

C2610-00041

MHX OUTLINE Rev. C

05/19/14D. CRONIN

REVISONS



SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558



OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5


.XX ± .25

.XXX ± .125X° ± .5 °



SURFACE FINISH: 1.6

5.00

5.00

.71

0.8±.1

3.75

.45

.50

4.70

1.40

2.35

1.40

.45

.50

4.78

4.782.14

.50

.40

.50

.50.50

4.68

3.68

4.68

2.14

.40

.400 .40

.40.60 .60

1/117.000

C2610-00041

MHX OUTLINE Rev. C

05/19/14D. CRONIN

REVISONS



SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558



OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5


.XX ± .25

.XXX ± .125X° ± .5 °



SURFACE FINISH: 1.6

5.00

5.00

.71

0.8±.1

3.75

.45

.50

4.70

1.40

2.35

1.40

.45

.50

4.78

4.782.14

.50

.40

.50

.50.50

4.68

3.68

4.68

2.14

.40

.400 .40

.40.60 .60

1/117.000

C2610-00041

MHX OUTLINE Rev. C

05/19/14D. CRONIN

REVISONS



SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558



OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5


.XX ± .25

.XXX ± .125X° ± .5 °



SURFACE FINISH: 1.6

5.00

5.00

.71

0.8±.1

3.75

.45

.50

4.70

1.40

2.35

1.40

.45

.50

4.78

4.782.14

.50

.40

.50

.50.50

4.68

3.68

4.68

2.14

.40

.400 .40

.40.60 .60

1/117.000

C2610-00041

MHX OUTLINE Rev. C

05/19/14D. CRONIN

REVISONS



SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558



OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5


.XX ± .25

.XXX ± .125X° ± .5 °



SURFACE FINISH: 1.6

5.00

5.00

.71

0.8±.1

3.75

.45

.50

4.70

1.40

2.35

1.40

.45

.50

4.78

4.782.14

.50

.40

.50

.50.50

4.68

3.68

4.68

2.14

.40

.400 .40

.40.60 .60

1/117.000

C2610-00041

MHX OUTLINE Rev. C

05/19/14D. CRONIN

REVISONS



xlamp® mH-B leds


15


15

taPe and reel

AllCreecarriertapesconformtoEIA-481D,AutomatedComponentHandlingSystemsStandard.

All dimensions in mm.

SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


X° ± .5 °.XXX ± .010.XX ± .03.X ± .06


.XX ± .01

.XXX ± .005X° ± .5 °

UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN INCHES

AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:

SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558


UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANYCONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOTCONTANED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

SURFACE FINISH: 63

330+.25-.75

12.4+1.0-.5MEASURED AT EDGE

16.4+0.2.0MEASURED AT HUB

12.4+.2

.0MEASURED AT HUB

±.213.1

1.9±.4

±.421

60° 60°

1/10.500

A2400-00009

REEL, 13" X 12MM, 3 PIECE SNAP

-

ANTI-STATIC HIPS

----

----

09/29/09D. CRONIN

2400-00009INDEX QTY ITEM COMMENTS

1 1 2400-00009-CORE2 2 2400-00009-REEL

REVISONS


SIZE

TITLE

OF

REV.

SHEET

CDRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

6 5 4 3 2 1

A

B

C

D

Phone (919) 313-5300Fax (919) 313-5558



OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5


.XX ± .25

.XXX ± .125X° ± .5 °



SURFACE FINISH: 1.6

Trailer160mm (min) of

empty pocketssealed with tape

(15 pockets min.)

Loaded Pockets(1000 Lamps)

Leader400mm (min.) of

empty pockets with at least 100mmsealed by tape

(40 empty pockets min.)

12

1.754

8 3.35

1/13.000

B2402-00012

XM LOADING SPEC

--

--

----

----

06/08/10D. CRONIN

REVISONS


A Loaded pocket count was 750 DDS 11/8/10 BS

B MADE CATHODE AND ANODE NOTE LARGER DC 2/26/12

END START

User Feed Direction

CATHODE SIDE

ANODE SIDE

12346 5

D

C

B

A

APP'DDATEBY

REVISIONS

REV DESCRIPTION

SIZE

TITLE

OF

REV.

SHEET

ADRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

4600 Silicon Drive

Fax (919) 313-5558

Durham, N.C 27703Phone (919) 313-5300


OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .010.XX ± .03.X ± .06


.XX ± .01

.XXX ± .005X° ± .5 °



SURFACE FINISH: 63 1/1DRAWING SCALE

A 2402-00011

XM 5050 CARRIER TAPE

4/23/10 D. CRONIN

CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275

.36[.014]T

5.40[.213]Ao

3.35[.132]Ko

3.0° 5.40[.213]Bo

2.00[.079]P2

4.00[.157]Po

Do1.50 +.10-.00 .0591 +.0039

-.0000 [ ]

10.25[.404]

E2

7.0°

12.00[.472]NOMINAL

12.30 [.484]

MAXW

1.75[.069]E1

5.50[.217]F

1.50[.059] D18.00[.315]

P

POCKET SIZEAo - 5.40mm [.213"]Bo - 5.40mm [.213"]Ko - 3.35mm [.132"]

12346 5

D

C

B

A

APP'DDATEBY

REVISIONS

REV DESCRIPTION

SIZE

TITLE

OF

REV.

SHEET

ADRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

4600 Silicon Drive

Fax (919) 313-5558

Durham, N.C 27703Phone (919) 313-5300


OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .010.XX ± .03.X ± .06


.XX ± .01

.XXX ± .005X° ± .5 °




A 2402-00011


4/23/10 D. CRONIN


.36[.014]T

5.40[.213]Ao

3.35[.132]Ko

3.0° 5.40[.213]Bo

2.00[.079]P2

4.00[.157]Po

Do1.50 +.10-.00 .0591 +.0039

-.0000 [ ]

10.25[.404]

E2

7.0°

12.00[.472]NOMINAL

12.30 [.484]

MAXW

1.75[.069]E1

5.50[.217]F

1.50[.059] D18.00[.315]

P


12346 5

D

C

B

A

APP'DDATEBY

REVISIONS

REV DESCRIPTION

SIZE

TITLE

OF

REV.

SHEET

ADRAWING NO.

DATE

DATE

DATE

CHECK


MATERIAL

APPROVED

DRAWN BY


SCALE

A

B

C

D

123456

4600 Silicon Drive

Fax (919) 313-5558

Durham, N.C 27703Phone (919) 313-5300


OF CREE INC.

NOTICE

X° ± .5 °.XXX ± .010.XX ± .03.X ± .06


.XX ± .01

.XXX ± .005X° ± .5 °




A 2402-00011


4/23/10 D. CRONIN


.36[.014]T

5.40[.213]Ao

3.35[.132]Ko

3.0° 5.40[.213]Bo

2.00[.079]P2

4.00[.157]Po

Do1.50 +.10-.00 .0591 +.0039

-.0000 [ ]

10.25[.404]

E2

7.0°

12.00[.472]NOMINAL

12.30 [.484]

MAXW

1.75[.069]E1

5.50[.217]F

1.50[.059] D18.00[.315]

P


xlamp® mH-B leds


16


16

PackaGinG

Label with Cree Bin Code, Qty, Lot #

Label with Cree Bin Code, Qty, Lot #

Vacuum-Sealed Moisture Barrier Bag

Dessicant (inside bag)

Humidity Indicator Card (inside bag)

Patent Label

Label with Customer Order Code, Qty, Reel ID, PO #

Patent Label

Label with Cree Bin Code, Qty, Reel ID


Label with Cree Order Code, Qty, Reel ID, PO #

Label with Cree Order Code, Qty, Reel ID, PO #


Unpackaged Reel

Packaged Reel

Boxed Reel

Documents

CLD-DS102 Rev 0 cree Xlamp mh-B leds - Mouser Electronics · CLD-DS102 Rev 0 Product family data sheet ... C4 475 538 65F MHBAWT-0000- ... XLAMP ® MH-B LeDS copyright 2010 cree,