Control Panel Catalogue - ECS · The P85 Panel, engineered and built by ECS, is a superior panel offering the powerful, yet simple-to-configure PV485 display. This display is part

Control Panel

Catalogue

ecs6001 Revision A, 17/03/18 Catalogue section 10

In order to consistently bring you the highest quality products, we reserve the right to change our specifications and designs at any time.

PART NO SYSTEM VOLTAGE

760 30 SEC

TIMER

RELAY

LOW OIL

PRESSURE HIGH ENGINE

TEMPERARURE V-BELT WARNING

ONLY SHUTT DOWN

P40-12V 12VDC X √ √ √ √ X

P40-24V 24VDC X √ √ √ √ X

P40R-12V 12VDC √ √ √ √ X √ P40R-24V 24VDC √ √ √ √ X √

P40 Control Panel Basic control panel for mechanical engines

Features

Engine and pump protection for

mobile or stationary applications

Hour meter with charge fail and

fault light

Instant shutdown or warning only

Compact and easy to install

P 40 series panels are a rugged, dependable solution for mechanical (non-ECU) engine or pump

fault monitoring and protection. Their compact size and ease of installation make these panels

highly suited to mobile or stationary engine-driven applications such as earth moving equipment

and pumps.

P 40 series panels use accurate and reliable engine mounted switches for indication and fault

shutdown.

All P 40 panels feature Switches for oil pressure (0 - 100psi / 0 – 7 bar) and coolant temperature

(50 – 120°C). Options are also available for indication/shutdown of pump water pressure

(0 – 20 bar), oil temperature (60 – 140°C) and auxiliary contact shutdown: see ‘how to order’

Each panel uses a robust steel, black powder coated enclosure.

Standard panels are supplied complete with crimped wires for electrical connection (battery

positive, battery negative and oil and temperature) and a wiring diagram. The P 40 series is

designed for use on 12VDC and 24VDC engines with energised-to-run type fuel solenoids.

HOW TO ORDER

DESCRIPTION


SPECIFICATIONS PIN ASSIGNMENT

Operating voltage: Specify when ordering 12VDC or 24VDC

Inputs: Oil pressure, Temperature, Belt break switch

And Charge fail (optional Water level switch)

Outputs: Run (Solenoid hold) relay contact 10A max

Start (Crank) positive via push button 10A max

Fault lights: Red (Charge fail), Green (fault indication)

General: Case finish, steel black powder coat.

IP65 sealed

Operating temp. -35°C to +85°C

Dimensions (w x h x d) 128 x 168 x 100 mm

4 WAY

CONNECTOR

8 WAY

CONNECTOR

1 Battery + 1 Alternator D+

2 Battery - 2 Alternator “W”

3 Start output 3 Oil pressure

4 Solenoid hold 4 Engine temperature

5 V-Belt switch

6 Water level(optional)

7 Spare

8 Spare

ecs6002

Revision A, 17/03/18 Catalogue section 10



FAILSAFE SYSTEM

LOW OIL


TEMPERARURE V-BELT CHARGE

FAIL SHUTT DOWN

P60-12V 12VDC X √ √ √ √ √ P60-24V 24VDC X √ √ √ √ √

P60FS-12V 12VDC √ √ √ √ √ √ P60FS-24V 24VDC √ √ √ √ √ √

P60 Control Panel Keystart panel for mechanical engines

Features

· Operator controlled start/stop

· Keyswitch operation with hour meter

· Automatic fault shutdowns and

Alarm output

· Timed preheat output

· Overspeed shutdown driven

From magnetic pickup or

Generator AC

from

magnetic pickup or

generator AC

The P60 panel provide manual start/stop and automatic fault protection for generators, pumps and

other engine-driven applications.

Operator control is by a 4 posit ion keyswitch, with the key removable only in the Stop/Reset (O)

posit ion. Outputs allow control of engine fuel (energized to run), starter motor and preheat. The

Keystart also has an alarm output for remote or audible warning of faults.

Indication of engine status and faults is by six LEDs and icons. Four switch inputs (opening neg

inputs on fault) enable automatic shutdown on engine low oil pressure, high coolant temperature

and auxil iary faults. The panel has a fully adjustable engine overspeed shutdown feature,

configurable for either generator AC or magnetic pickup speed signals. Charge alternator

excitation and a charge fail warning LED are fitted as standard.

Electrical connection is by quick-connect, spring-clamp terminal blocks. A universal 7 - 30VDC

power supply permits operation with 12 or 24VDC engine batteries, with engine crank-dip

voltage protection fitted as standard.

HOW TO ORDER

DESCRIPTION



Operating voltage: 12 – 16 VDC






IP65 sealed



4 WAY

CONNECTOR

8 WAY

CONNECTOR





5 V-Belt switch


7 Spare

8 Spare

ecs6007



FEATURES

Compatible with all

mechanical and electronic

engines

Fully programmable to

monitor multiple parameters

Automatic fault shutdown

protection and indication

Can be used across many

applications

10 X Inputs and outputs (I/O)

P80 Control Panel For electronic & mechanical engines

HOW TO ORDER

DESCRIPTION

The Murphy Link Series P80 Panel, engineered and built by ECS, is a superior panel offering

that includes the powerful, yet simple-to-configure PV380 display. This display is part of the

Murphy PowerView® family and provides monitoring of Tier 4/Euro Stage 4 compliant electronic

engines. The PV380 monitors multiple J1939 parameters and provides basic engine

alarm/shut-down information.

The P80 panel has the ability for the software to be fully configured from the front user

interface. If the factory default parameters are not the desired set points, the packager or

operator has the ability to change these settings. The configuration tool also allows for the

splash screen to incorporate a company logo.

The flexibility of the P80 allows for the same panel to be used across many applications. This

provides the operator familiarity with the display and panel in any application. The panel utilizes

industry standard Deutsch connectors and is compatible for use on the simplest to the most

advanced, fully electronic Tier 4 engines, our panel can be used for both above and

underground applications for more advanced engine monitoring and protection at a low cost.

P80-12 12VDC PANEL P80-24 24VDC PANEL PLEASE USE THE PANEL QUESTIONARE TO ORDER.


SPECIFICATIONS

Operating Voltage: 6-36 VDC; reverse polarity protected

(display only)

Operating Temperature: -40° to 185° F (-40° to 85° C)

Storage Temperature: -40° to 185° F (-40° to 85° C)

Total Current Consumption: 10 W Max (display only)

Viewing Area: 3.8” (97 mm) QVGA (320 x 240 pixels);

mono-chrome transflective LCD with white LED backlight

and heater Viewing Angle: ±50° horizontally; +45° / -60°

vertically

Panel Enclosure: Powder-coated

Alarms: Red and amber warning LEDs; Set point

triggered output for external piezo buzzer or shut-down

relay

Mating Connectors: 21 Position, Deutsch HDP26-24-

21SE

Sealing: IP66 and 67 (Display only)

Vibration and Shock: 7.86 g random vibe (5-2000 Hz)

and ±50 g shock in 3 axes (Display only)

Communications: CAN (SAE J1939) and RS-485

Modbus Languages: English, Spanish, French,

Italian and German

Outputs (2): (2) 500 mA; switched low-side

Inputs (8): (4) Resistive Analog

(3) Analog: 0-5 V, 4-20 mA (analog or digital

(1) Frequency (2 Hz - 10 KHz, 3.6 VAC-120 VAC)

EMC/EMI: 2004/108/EC and 2006/95/EC directives

EN61000-6-4:2001 (emission)

EN61000-6-2:2001 (immunity)

EN50121-3-2 and EN12895

SAE J1113/2, 4, 11, 12, 21, 24, 26 and 41

ecs6008



FEATURES

Compatible with all

mechanical and electronic

engines


monitor multiple parameters



Can be used across many

applications

Data logging


P85 Control Panel For electronic & mechanical engines

HOW TO ORDER

DESCRIPTION

The P85 Panel, engineered and built by ECS, is a superior panel offering the powerful, yet

simple-to-configure PV485 display. This display is part of the Murphy PowerView® family and

provides monitoring of Tier 4/Euro Stage 4 compliant electronic engines. The PV485 monitors

multiple J1939 parameters and provides basic engine alarm/shut-down information.








advanced, fully electronic Tier 4 engines, our panel can be used for both above and

underground applications for more advanced engine monitoring and protection at a low cost.

P85-12 12VDC PANEL P85-24 24VDC PANEL PLEASE USE THE PANEL QUESTIONARE TO ORDER.


SPECIFICATIONS

Display: Bonded 4.3”/109mm color Trans missive TFT LCD

Resolution: WQVGA, 480 x 272 pixels, 16-bit color

Aspect Ratio: 16:9

Orientation: Landscape

Backlighting: LED, 900-1000 cd/m2 (30,000 hr. lifetime)

Microprocessor: Freescale i.MX35 32bit, 532Mhz

Operating System: QNX Real-Time Operating System Flash

Memory: 256 MB

RAM: 128 Mbytes DDR2 SDRAM

Operating Voltage: 6-32 VDC, protected against reverse

Polarity and load dump

Power Consumption: 10W max.

CAN: (1) CAN 2.0B

Protocols: J1939, Freeform CAN support

Connection: (1) 35-pin AMP seal connector (AMP 776231-4)

Keyboard: (5) tactile buttons USB: (1) USB 2.0 host

(full speed)

Digital Inputs: (3) Digital Inputs

Digital Outputs: (4) Low Side Open-drain, capable of sinking

500 mA

Analog Inputs: (6) total, (4) software configurable (0-5V,

4-20mA, Resistive) + Battery Voltage + 2nd Battery Voltage

Analog Outputs: (1) 0-5V

Frequency Inputs: (1) Alternator and Magnetic Pickup

Real-time clock: with battery backup

Communication:

(1) CAN 2.0B according to ISO-11898-2; J1939

and CANopen protocols; proprietary messaging

Environmental

Operating Temperature: -40°C to +85°C (-40°F

to +185°F)

Storage Temperature: -40°C to +85°C (-40°F to

+185°F)

Protection: IP 67, front and back

Emissions/Immunity: SAE J1113 or customer-

specified; (CE) - EN61000-6-2, EN12895, ISO

13766

Vibration: Random vibration, 7.86 Grms (5-2000

Hz), 3 axes

Shock: ± 50G in 3 axes

ecs6004



FEATURES

Compatible with all

mechanical engines

Failsafe Keystart module for

operator manual start/stop

control



Hours run counter

Tachometer


FAILSAFE SYSTEM

LOW OIL



FAIL SHUTT DOWN

P100-12V 12VDC X √ √ √ √ √ P100-24V 24VDC X √ √ √ √ √

P100FS-12V 12VDC √ √ √ √ √ √ P100FS-24V 24VDC √ √ √ √ √ √

P100 Control Panel Control panel for mechanical engines

HOW TO ORDER

DESCRIPTION

Panel P100 provides operator-controlled start/stop, and automatic fault shutdown and indication for mechanical (non-ECU) engines. The panels are primarily used in stationary engine applications such as pumps, crushers, shredders, etc.

Operator control is through a 3 position key switch on a Murphy Keystart module. The key is common to all Keystart’s and is removable only in the Stop/Reset (O) position. A P100FS (Failsafe Keystart) is also available for order.

Outputs are provided for the control of engine fuel, starter and preheat. Automatic engine shutdown may be triggered by three inputs - oil pressure, coolant temperature and coolant level - designed for operation with engine-mounted switch contacts that opens from negative DC during fault. A charge fail connection drives charge alternator excitation current and LED indication during fault conditions.

The instruments is housed in a rugged, IP65 metal case. Electrical connection is through an integral harness with ring, blade and Deutsch connectors, for direct mating with the engine.








Fault lights: Red (Charge fail)


IP65 sealed



4 WAY

CONNECTOR

8 WAY

CONNECTOR





5 V-Belt switch


7 Spare

8 Spare

300

mm

250 mm

150 mm

ecs6006



FEATURES

Compatible with all makes of

J1939 Canbus electronic

compressors

Load switch

E- stop

Fault finding made easy

Tier 4/Euro stage IV ready

Data logging (programmable)

P200 Control Panel For electronic driven compressors

HOW TO ORDER

DESCRIPTION

The P200 panel incorporates a PowerView 485 which is a customizable, all-in-one color display

and controller designed to meet the needs of modern electronic engines and equipment

applications. Its rugged design offers a wide array of configurable I/O and supports both

mechanical and J1939 electronic engines.

The PV485 also supports Tier 4 and stage IV engines, helping to make your transition to Tier 4

easier.

The PV485 controller is compatible with the PowerVision Configuration Studio® software, so

custom configurations can be quickly developed. With the PowerVision Configuration Studio

software, it is easy to define the user interface screens, as well as the functionality and

sequence of events controlled by the PV485. You can configure equipment control such as:

auto start, pressure control, data logging and alarms. You can even add custom graphics and

company branding to the user interface. Compressor load is done via the load valve and a

mechanical air actuator operating the electronic throttle

Please specify make and model of the unit.

System voltage.

Engine being used with ECU model.


SPECIFICATIONS

Display: Bonded 4.3”/109mm color trans missive TFT LCD Resolution:

WQVGA, 480 x 272 pixels, 16-bit color

Aspect Ratio: 16:9




Operating System: QNX Real-Time Operating System

Flash Memory: 256 MB


Operating Voltage: 6-32 VDC, protected against reverse polarity and

load dump


CAN: (1) CAN 2.0B



Keyboard: (5) tactile buttons

USB: (1) USB 2.0 host (full speed)


Digital Outputs: (4) Low Side Open-drain, capable of sinking 500 mA

Analog Inputs: (6) total, (4) software configurable (0-5V, 4-20mA,

Resistive) + Battery Voltage + 2nd Battery Voltage




COMUNICATION

(1) CAN 2.0B according to ISO-11898-

2; J1939 and CANopen protocols;

proprietary messaging

ENVIROMENTAL

Operating Temperature: -40°C to

+85°C (-40°F to +185°F)

Storage Temperature: -40°C to +85°C

(-40°F to +185°F)


Emissions/Immunity: SAE J1113 or

customer-specified; (CE) - EN61000-6-

2, EN12895, ISO 13766

Vibration: Random vibration, 7.86 Grms

(5-2000 Hz), 3 axes


PANEL

Protection: IP65

Connection: 21 Pin connector

Dimensions: 300 x 250 x 150 mm

ecs6009



FEATURES

Compatible with all

mechanical & electronic

engines

Operator manual start/stop

control



Tier 4 compliant

TSC1 throttle control via the

J1939 network

P300 Control Panel For Stationary engine applications

HOW TO ORDER

DESCRIPTION

Panel P300 provides operator-controlled start/stop, and automatic fault shutdown and

indication for mechanical and electronic engines. The panels are primarily used in stationary

engine applications such as pumps, crushers, drill rigs, etc.

Operator control is through a 3 position key switch on the panel.

Outputs are provided for the control of engine fuel and start signals. Automatic engine

shutdown may be triggered by inputs such as oil pressure, coolant temperature and coolant

level - designed for operation with engine-mounted sensors or switches.

The instruments is housed in a rugged, IP65 metal case. Electrical connection is through an

integral harness with ring, blade and Deutsch connectors, for direct mating with the engine.

P300-12 12VDC Panel

P300-24 24VDC Panel

Please use the panel questionnaire to order


SPECIFICATIONS

Operating Voltage: 6-36 VDC; reverse polarity protected

(display only)

Operating Temperature: -40° to 185° F (-40° to 85° C)

Storage Temperature: -40° to 185° F (-40° to 85° C)

Total Current Consumption: 10 W Max (display only)

Viewing Area: 3.8” (97 mm) QVGA (320 x 240 pixels);

mono-chrome transflective LCD with white LED backlight

and heater Viewing Angle: ±50° horizontally; +45° / -60°

vertically

Panel Enclosure: Powder-coated

Alarms: Red and amber warning LEDs; Set point

triggered output for external piezo buzzer or shut-down

relay


21SE

Sealing: IP66 and 67 (Display only)

Vibration and Shock: 7.86 g random vibe (5-2000 Hz)

and ±50 g shock in 3 axes (Display only)


Modbus Languages: English, Spanish, French,

Italian and German

Outputs (2): (2) 500 mA; switched low-side

Inputs (8): (4) Resistive Analog

(3) Analog: 0-5 V, 4-20 mA (analog or digital

(1) Frequency (2 Hz - 10 KHz, 3.6 VAC-120 VAC)

EMC/EMI: 2004/108/EC and 2006/95/EC directives

EN61000-6-4:2001 (emission)

EN61000-6-2:2001 (immunity)

EN50121-3-2 and EN12895

SAE J1113/2, 4, 11, 12, 21, 24, 26 and 41

ecs6010



Compatible with all


engines


control




J1939 network

P410 Control Panel For Stationary and mobile pump applications

HOW TO ORDER

DESCRIPTION

FEATURES

The ECS P410 Panel, engineered and built by ECS, is a superior panel offering which includes

the powerful, yet simple-to-configure MPC-10 Controller. The MPC-10 is a general, all-purpose

manual/auto start and manual/auto throttling engine controller designed with rental applications

in mind. The controller is purposed primarily for applications where a wide array of inputs and

outputs are not required.

The MPC-10 supports J1939 CAN protocols for electronically governed engines as well as

analog sensors on mechanical engines for fault and safety shutdowns. The MPC-10 follows a

standard operating sequence of 22 machine states that happen in a predetermined order.

Machine states can be set to zero if not needed or adjusted to fit the application. The menu

structure is incredibly versatile, with the ability to change many parameters and settings from

the face without the need of a PC tool, if desired.

The flexibility of the MPC-10 controller allows for the same control panel to be used across

many applications. This provides the operator familiarity with the controller and control panel in

any application.

P410-12 12VDC Panel

P410-24 24VDC Panel



SPECIFICATIONS

Operating Voltage: 8-32VDC, reverse polarity and

load dump protected

Operating Temperature: -40° to +85°C (-40° to 185°F)

Storage Temperature: -40° to +85°C (-40° to 185°F)

Total Current Consumption: Power on in stopped state;

117 mA at 12 VDC. Power on in standby mode;

52 mA at 12 VDC.

Enclosure: IP65 powder coated

Connectors: 21 Position, Deutsch HDP26-24-21SE,

31 Position, Deutsch HDP26-24-31SE

Communications: (1) CAN J1939

(1) RS485, Modbus RTU

(1) USB 2.0B for Programming

Outputs (8):

(3) Relays: 10A, SPDT, Form C (30 VDC @ 10A max.),

30A max aggregate @ 85C

(2) Low-side (1A)

(2) High-side (1A)

(1) Dedicated Alternator Excite (provides Charge

Fail Fault if unable to excite alternator)

Inputs (9):

(5) Digital, configurable (high/low)

(3) Analog, configurable (4-20mA, 0-5V, resistive)

(1) Frequency, supporting Magnetic pickup (30Hz -

10 kHz, 2.0VAC-120VAC) and Engine Alternator

(30Hz - 10 kHz, 4.5 VRMS - 90 VRMS)

ecs6015



Compatible with all


engines


control




J1939 network

Corrosion resistant

P410M Marine Control Panel For Stationary and mobile pump applications

HOW TO ORDER

DESCRIPTION

FEATURES

The ECS P410M Panel, engineered and built by ECS, is a superior panel offering which

includes the powerful, yet simple-to-configure MPC-10 Controller. The MPC-10 is a general,

all-purpose manual/auto start and manual/auto throttling engine controller designed with rental

applications in mind. The controller is purposed primarily for applications where a wide array of

inputs and outputs are not required.

The MPC-10 supports J1939 CAN protocols for electronically governed engines as well as

analog sensors on mechanical engines for fault and safety shutdowns. The MPC-10 follows a

standard operating sequence of 22 machine states that happen in a predetermined order.

Machine states can be set to zero if not needed or adjusted to fit the application. The menu

structure is incredibly versatile, with the ability to change many parameters and settings from

the face without the need of a PC tool, if desired.

The flexibility of the MPC-10 controller allows for the same control panel to be used across

many applications. This provides the operator familiarity with the controller and control panel in

any application.

P410M-12 12VDC Panel

P410M-24 24VDC Panel



SPECIFICATIONS

Operating Voltage: 8-32VDC, reverse polarity and

load dump protected

Operating Temperature: -40° to +85°C (-40° to 185°F)

Storage Temperature: -40° to +85°C (-40° to 185°F)

Total Current Consumption: Power on in stopped state;

117 mA at 12 VDC. Power on in standby mode;

52 mA at 12 VDC.

Enclosure: IP67 polycarbonate

Connectors: 21 Position, Deutsch HDP26-24-21SE

Communications: (1) CAN J1939

(1) RS485, Modbus RTU

(1) USB 2.0B for Programming

Outputs (8):

(3) Relays: 10A, SPDT, Form C (30 VDC @ 10A max.),

30A max aggregate @ 85C

(2) Low-side (1A)

(2) High-side (1A)

(1) Dedicated Alternator Excite (provides Charge

Fail Fault if unable to excite alternator)

Inputs (9):

(5) Digital, configurable (high/low)

(3) Analog, configurable (4-20mA, 0-5V, resistive)

(1) Frequency, supporting Magnetic pickup (30Hz -

10 kHz, 2.0VAC-120VAC) and Engine Alternator

(30Hz - 10 kHz, 4.5 VRMS - 90 VRMS)

ecs6011



The P420 Panel, engineered and built by ECS, is a superior panel offering which includes the

powerful, yet simple-to-configure MPC-20 Controller. This controller is part of the Murphy

Powercore® family and was developed to meet the need of manual or automatic control

whether it’s starting/stopping, throttling or both. This controller also has the flexibility to be used

on either mechanically or electronically governed engines supporting SAE J1939 CAN

communications.


interface or PC configuration tool. If the default parameters set by ECS are not the desired set

points for a factory default reset, the packager or operator has the ability to change these

settings with the PC configuration tool then load with a USB thumb drive1 and USB

programming harness1. The configuration tool also allows for the splash screen to incorporate

a company logo when powered on. The flexibility of the MPC-20 controller allows for the same

control panel to be used across many applications. This provides the operator familiarity with

the controller and control panel in any application. The Control Panel utilizes industry standard

Deutsch connectors and is compatible for use on the simplest mechanical engine to the most

advanced, fully electronic Tier 4 engines.

Compatible with all

mechanical &

electronic engines

Operator manual

start/stop control

Automatic fault

shutdown protection

and indication

TSC1 throttle control

via the J1939 network

P420 Control Panel For Stationary and mobile pump applications

HOW TO ORDER

DESCRIPTION

FEATURES

P420-12 12VDC Panel

P420-24 24VDC Panel



SPECIFICATIONS

Operating Voltage: 8-32 VDC

Operating Temperature: -40° to +85° C (-40° to 185° F)

Storage Temperature: -40° to +85° C (-40° to 185° F)

Total Current Consumption:

18 W Max without 2 2 A High-sides active

146 W Max with 2 2 A High-sides active

Enclosure: Powder-coated cold rolled steel


21SE 31 Position, Deutsch HDP26-24-31SE


Modbus

Outputs (13):

(2) 1 A Max Low-side

(2) 2 A Max High-side

(2) 200 mA Max 5 VDC

(1) 0-5 VDC Analog

(6) 10 A Max Form C Relays

Inputs (15):

(8) Analog, configurable as Resistive, 0-5 VDC or 4-

20 mA

(6) Digital, Configurable as Battery or Ground

(1) Frequency, (2 Hz - 10 KHz, 3.6 VAC-120 VAC)

ecs6003



PART NO SYSTEM

VOLTAGE 760 30 SEC

TIMER RELAY

20P100 LOW OIL

PRESSURE

20T120XM ENGINE

TEMP

20T160XM OIL

TEMP

20T160XM OIL

TEMP

WATER LEVEL

OIL LINE &

FITTINGS P502-12V 12VDC √ √ √ X X √ √ P502-24V 24VDC √ √ √ X X √ √ P503-12V 12VDC √ √ √ √ X √ √ P503-24V 24VDC √ √ √ √ X √ √ P504-12V 12VDC √ √ √ √ √ √ √ P504-24V 24VDC √ √ √ √ √ √ √

P500 Swichgage Panels Shut down panels for diesel engines

HOW TO ORDER

DESCRIPTION

SPECIFICATI

Features

• Engine and pump protection for mobile or stationary applications

• Swichgage indication and automatic shutdown of all diesel engines

• Instant shutdown or warning before shut down

• Compact and easy to install

P500 series panels are a rugged, dependable solution for mechanical (non-ECU) engine or pump fault monitoring and protection. Their compact size and ease of installation make these panels highly suited to mobile or stationary engine-driven applications such as tractors, PTO devices, earth moving equipment and pumps.

P500 series panels use the accurate and reliable Murphy Swichgage® for indication and fault shutdown. All P500 panels feature Swichgages for oil pressure (0 - 100psi / 0 – 7 bar) and coolant temperature (50 – 120°C). Options are also available for indication/shutdown of pump water pressure (0 – 20 bar), oil temperature (60 – 140°C) and auxiliary contact shutdown: see how to order for a full feature reference.

Each panel uses a robust steel, black painted enclosure, fitted with a rotating bracket for ease of installation and use.

Standard panels are supplied complete with a 2 meter oil line and adaptors, 3 crimped wires for electrical connection (battery positive, battery negative and fuel/shutdown output) and a wiring diagram. The P500 series is designed for use on 12VDC and 24VDC engines with energized-to-run type fuel solenoids.


LEVEL SENSOR

AVAILABLE

M14 & ¼ NPT

When ordering please specify the following to our sales team:

• Temp gauge capillary length • Oil pressure hose length • Adaptor needed for engine temp probe (5/8-18UNF to xx) • Voltage of system • Time delay before shut down (immediate shut down

standard) • Water level if needed

HOW TO ORDER - CONTINIUED

P502

P503

P504

PRESSURE HOSE

CUTT TO SIZE

ecs6005



FEATURES

Compatible with all

mechanical engines

Failsafe Keystart module for

operator manual start/stop

control



Hours run counter


FAILSAFE SYSTEM

LOW OIL



FAIL SHUTT DOWN

P600-12V 12VDC X √ √ √ √ √ P600-24V 24VDC X √ √ √ √ √

P600FS-12V 12VDC √ √ √ √ √ √ P600FS-24V 24VDC √ √ √ √ √ √

P600 Control Panel Keystart panel for mechanical engines

HOW TO ORDER

DESCRIPTION

Panel P600 provides operator-controlled start/stop, and automatic fault shutdown and indication for mechanical (non-ECU) engines. The panels are primarily used in stationary engine applications such as pumps, crushers, shredders, etc.

Operator control is through a 3 position key switch on a Murphy Keystart module. The key is common to all Keystart’s and is removable only in the Stop/Reset (O) position. A P600FS (Failsafe Keystart) system is also available for order.

Outputs are provided for the control of engine fuel, starter and preheat. Automatic engine shutdown may be triggered by three inputs - oil pressure, coolant temperature and coolant level - designed for operation with engine-mounted switch contacts that opens from negative DC during fault. A charge fail connection drives charge alternator excitation current and LED indication during fault conditions.

The instruments is housed in a rugged, IP65 metal case. Electrical connection is through an integral harness with ring, blade and Deutsch connectors, for direct mating with the engine.








Fault lights: Red (Charge fail)


IP65 sealed



4 WAY

CONNECTOR

8 WAY

CONNECTOR





5 V-Belt switch


7 Spare

8 Spare

300

mm

250 mm

150 mm

ecs6012



P700 Control Panel Replacement panel for Atlas Copco compressors

HOW TO ORDER

DESCRIPTION

Designed for Atlas Copco

compressors

Immediate shut down on fault

using mechanical switch

gauges

Designed to fit existing

mounting holes

Compatible with any make

engine fitted to the unit

Panel includes full wiring

harness.

FEATURES

P700-12 12VDC Panel

P700-24 24VDC Panel


The P700 panel provides operator

controlled start and stop of the unit.

Automatic shutdown protection in

the event of a fault on both the

engine and the air end.

Operator control is via a on/off switch and a bypass button. The bypass button opens the

shutdown circuit for the operator to start and build up engine oil pressure. When the engine is

running the bypass button can be released to activate the safety circuit.

A simple on/off switch is fitted for load and unload of the air system. The panel is sold already

prewired for ease of fitment. The P700 panel is fitted with mechanical switch gauges to allow

the client to determine the shutdown values.


SPECIFICATIONS

Operating Voltage: 12 or 24 VDC



Total Current Consumption: 13 Amps


Starting method: Push button

Stopping method: On/off toggle switch

Wiring: Included with panel

Gauges used: Tachometer, engine oil pressure,

engine temperature, 2x air end temperature, fuel

and hour meter.

Outputs:

Start (crank signal)

Solenoid (energize and hold signal)

Compressor load signal (on/off switch)

Inputs:

Battery +

Battery –

Engine RPM (“w“ terminal alternator)

400 mm

525

mm

468 mm

269 mm

68 mm

0

0 10 mm 390 mm

ecs6013



P800 Control Panel Replacement panel for (IR) Ingersoll Rand compressors

HOW TO ORDER

DESCRIPTION

Designed for Ingersoll Rand

(IR) compressors

Immediate shut down on fault

using mechanical switch

gauges

Designed to fit existing

mounting holes

Compatible with any make

engine fitted to the unit

Panel includes full wiring

harness.

FEATURES

P800-12 12VDC Panel

P800-24 24VDC Panel


The P800 panel provides operator

controlled start and stop of the unit.

Automatic shutdown protection in

the event of a fault on both the

engine and the air end.

Operator control is via an on/off switch and a bypass button. The bypass button opens the

shutdown circuit for the operator to start and build up engine oil pressure. When the engine is

running the bypass button can be released to activate the safety circuit.

A simple on/off switch is fitted for load and unload of the air system. The panel is sold already

prewired for ease of fitment. The P800 panel is fitted with mechanical switch gauges to allow

the client to determine the shutdown values.


SPECIFICATIONS

Operating Voltage: 12 or 24 VDC



Total Current Consumption: 13 Amps


Starting method: Push button

Stopping method: On/off toggle switch

Wiring: Included with panel

Gauges used: Tachometer, engine oil pressure,

engine temperature, air end temperature, fuel and

hour meter.

Outputs:

Start (crank signal)

Solenoid (energize and hold signal)

Compressor load signal (on/off switch)

Inputs:

Battery +

Battery –

Engine RPM (“w“ terminal alternator)

360 mm

610

mm

571 mm

305 mm

39 mm

0

0 10.5 mm 349.5 mm

ecs6014



The P900 panels were developed for air cooled and liquid cooled engines powering truck mounted mobile drill rigs. Both panels feature Swichgage protection for low oil pressure and high engine temperature. Panel P900 A is a warning only panel with no shut down. Panel P900 B incorporates a Murphy Keystart module for shut down on low oil pressure and high engine temperature.

A P900 BFS panel is also available with a failsafe Keystart, should a wire come of or tampered with it will shut down.

Either these panels can be ordered with or without the 220VAC plug and Hertz meter depending if the drill rig have an onboard welder present. All emergency stop buttons can be incorporated into the P900 B for safety shut down if required by the site of operation.

Both panels are supplied with a complete wiring harness and connectors.

P900 Control Panels Drill rig applications

DESCRIPTION

P900 A P900 B


HOW TO ORDER

P900 A 12 or 24 VDC panel warning only

P900 B 12 or 24 VDC panel with shut down

P900 BFS 12 or 24 VDC panel with failsafe Keystart

Please use the panel questionnaire to order 3

50 m

m

220 mm

5 mm

175 mm

345 mm

5 mm 215 mm

0



Compatible with all mechanical

and electronic engines

Fully programmable to monitor

multiple parameters



Remote monitoring and tracking

in real time

Data logging


P1000 Control Panel Remote monitoring and tracking system

HOW TO ORDER

DESCRIPTION

FEATURES

The P1000 Panel, engineered and built by ECS, is a superior panel offering the powerful, yet

simple-to-configure PV485 display. This display is part of the Murphy PowerView® family and

provides monitoring of Tier 4/Euro Stage 4 compliant electronic and mechanical engines. The

PV485 monitors multiple J1939 parameters and provides basic engine alarm/shut-down

information.








advanced, fully electronic Tier 4 and mechanical engines, our panel can be used for both above

and underground applications for more advanced engine monitoring and protection at a low

cost.

The P1000 is also supplied with a CANect remote monitoring system to always know what your

expensive equipment are doing in real time via either Wi-Fi or GPRS. The system can be

configured to monitor and display any parameters you should need.

P1000-12 12VDC PANEL P1000-24 24VDC PANEL

PLEASE USE THE PANEL QUESTIONARE TO ORDER.

PV485

15A

20A


SPECIFICATIONS PV485 DISPLAY

Display: Bonded 4.3”/109mm color Trans missive TFT LCD

Resolution: WQVGA, 480 x 272 pixels, 16-bit color

Aspect Ratio: 16:9




Operating System: QNX Real-Time Operating System Flash

Memory: 256 MB


Operating Voltage: 6-32 VDC, protected against reverse

Polarity and load dump


CAN: (1) CAN 2.0B



Keyboard: (5) tactile buttons USB: (1) USB 2.0 host

(full speed)


Digital Outputs: (4) Low Side Open-drain, capable of sinking

500 mA

Analog Inputs: (6) total, (4) software configurable (0-5V,

4-20mA, Resistive) + Battery Voltage + 2nd Battery Voltage




Communication:

(1) CAN 2.0B according to ISO-11898-2; J1939

and CANopen protocols; proprietary messaging

Environmental

Operating Temperature: -40°C to +85°C (-40°F

to +185°F)

Storage Temperature: -40°C to +85°C (-40°F to

+185°F)


Emissions/Immunity: SAE J1113 or customer-

specified; (CE) - EN61000-6-2, EN12895, ISO

13766

Vibration: Random vibration, 7.86 Grms (5-2000

Hz), 3 axes




Compatible with all

mechanical and

electronic engines


monitor multiple

parameters

Automatic fault

shutdown protection and

indication

Remote monitoring and

tracking in real time

Data logging

46 X Inputs and outputs

(I/O)

Driver identification

Angle sensor

P1100 Control Panel Machine and Engine management system

DESCRIPTION

FEATURES

The P1100 Panel, engineered and built by ECS especially for the mining industry on trackless mining machines, is a superior panel offering the powerful, yet simple-to-configure PV780B display. This display is part of the Murphy PowerView® family and provides monitoring of Tier 4/Euro Stage 4 compliant electronic and mechanical engines. The PV780B monitors multiple J1939 parameters and provides detailed engine alarm/shut-down information.

The P1100 panel has the ability for the software to be fully configured to customer specification.

The system is also fitted with the following:

Card reader for driver information and identification. Inclination sensor to determine if machine is on a decline or incline for stopping

purposes. Monitoring system for machine data logging and file download via Wi-Fi and GPRS The system is PDS (Pedestrian detection system) ready to slow down and stop the

machine. Much more can be added to optimize the performance of your equipment.


For information on all items used please send an enquiry to [email protected]

SPECIFICATIONS

sect. 30 1800028rev. 2018/08/22

131

510

1520

2530

4055

7075

7880

MGC1000 Generator PanelThe MurphyLink Series MGC1000 Panel, engineered

and built by Enovation Controls’ Industrial Panel Division, is a superior panel offering which includes the powerful, yet simple-to-configure MPC-10 Controller. The MPC-10 is a general, all-purpose manual/auto start engine controller. The controller is purposed primarily for applications where a wide array of inputs and outputs are not required. The MPC-10 supports J1939 CAN protocols for electronically governed engines as well as analog sensors on mechanical engines for fault and safety shutdowns. The MPC-10 follows a standard operating sequence

of machine states that happen in a predetermined order. Machine states can be set to zero if not needed or adjusted to fit the application. The menu structure is incredibly versatile, with the ability to change many parameters and settings from the face without the need of a PC tool, if desired. The flexibility of the MPC-10 controller allows for

the same control panel to be used across many applications. This provides the operator familiarity with the controller and control panel in any application. The Control Panel utilizes industry-standard Deutsch Specifications

MPC-10 Controller Operating Voltage: 8-32 VDC, reverse polarity and load dump

protectedOperating Temperature: -40° to +85° C (-40° to 185° F)Storage Temperature: -40° to +85° C (-40° to 185° F)

Total Current Consumption: Power on in stopped state; 117 mA at 12 VDC. Power on in standby mode; 52 mA at 12 VDC.

Enclosure: Sheet MetalMating Connector: 21 Position, Deutsch HDP26-24-21SE

Communications: (1) CAN J1939(1) RS485, Modbus RTU(1) USB 2.0B for Programming

Outputs (8): (2) Relays: 10A, Dedicated B+ (30 VDC @ 10A max.), 30A max

aggregate @ 85C(2) Low-side (1A)(2) High-side (1A)(1) Dedicated Alternator Excite (provides Charge Fail Fault if

unable to excite alternator)Inputs (9): (2) Digital, configurable (high/low)(2) Analog, configurable (4-20 mA, 0-5V, resistive)(1) Frequency, supporting Magnetic pickup (30 Hz - 10 kHz,

2.0 VAC-120 VAC) and Engine Alternator (30 Hz - 10 kHz, 4.5VRMS - 90 VRMS)

Dimensions: 4.16 x 6.083 x 10.68 in. (360 x 155 x 271mm) (WxHxD)

connector and is compatible for use on the simplest mechanical engine to the most advanced, fully electronic Tier 4 engines, when used with the correct Murphy Industrial Harness1 (MIH) or John Deere OEM engine harnessing. The MGC1000 panel can be mounted directly to the

engine or engine/application cover. 1Please contact Industrial Panel Sales for application specifics and

MIH harnessing.

How to Order

Part Number Model and Description Notes

75700649 MGC1000 120 VAC Genset Panel

75700650 MGC1000 240/480 VAC Genset Panel

75001313Engine (mechanical) Harness, 21 Position Connector 10’ Whip Harness (3m approx.)

40000657 I/O Harness 12 Position Connector 5’ MPC10

40000658 E Stop PB Kit

78000668 USB Programming Harness

132

Product and Mounting Dimensions

MGC1000 Genset Panel

Deutsch 21 pin Connector Engine

PIN Function

A Reserved

B Battery +

C Reserved

D Starter Solenoid

E Battery -

F Reserved

G Fuel/ECU

H Reserved

J Alternator Excite

K Reserved

L Glowplug

M Reserved

N Reserved

P Reserved

R AUX. Output 1 (-)

S AUX. Output 2 (-)

T Frequency Input

U J1939 CAN LO

V J1939 CAN HI

W Temperature Sender

X Pressure Sender

Connector

5 Zurich Road, Aeroport, Spartan, Kempton Park South Africa, 1618

PO Box 13829, Norkem Park South Africa, 1618

Tel.: +27 11 391 1443 Fax: +27 86 510 2706

Email: [email protected] VAT no.: 4220210928 Reg. no.: 2004/007451/23

Customer Date Date To Complete Engine Make Engine Model Application What Kind of Engine ECU Mechanical ECU Model Communication Type J1939 J1708 RS458 Throttle Type Settings J1939 (TSC1) Mechanical PTO Throttle Mount Top Mount Side Mount Voltage 12 Volts DC 24 Volts DC Shutdown/ Warning

Disable ECU Warning only Fuel Solenoid Fuel Rack ( Solenoids)

Brake Solenoid Other Warning Procured Slow Down Stop Both Alarm Audible Flashing Light Steady Lights

Instrumentation Needed(Tick if applicable) PV 780 PV 480 PV 450 PV 380

MPC 10 MPC 20 Engine Oil Pressure SW SE DATA Logging (USB)

Engine Oil Temperature SW SE Engine Hours SW

Transmission Oil Pressure WS SE Transmission Hours SW

Transmission Oil Temperature SW SE Hydraulic Level SW

Engine Water Temperature SW SE Emergence Stop SW

High End Temperature SW SE Water Level SW

Low End Temperature SW SE Safety Belt Switch SW

Cylinder head Temperature SW SE Water Flow SW

Brake Pressure SW SE System Voltage SE

Accumulator Pressure SW SE Steering Pressure SE

Door Limit SW Ground Speed Seat switch SW Card Reader

Engine Over Speed SW Inclination Sensor Belt Brake SW Tachometer

Start Method Key Switch Push Buttons

Documents

Control Panel Catalogue - ECS · The P85 Panel, engineered and built by ECS, is a superior panel offering the powerful, yet simple-to-configure PV485 display. This display is part