Crawl & Cruise PlaygrPlaygroundound - Mattel...Crawl & Cruise PlaygrPlaygroundound Please keep this instruction sheet for future reference, as it contains important information. Adult

Crawl & CruisePlayground

Crawl & CruisePlayground

Crawl & CruisePlayground™

Please keep this instruction sheet for future reference, as it contains important information.

Adult assembly is required.Tool required for assembly: Phillips screwdriver (not included).

Requires three "C" (LR14) alkaline batteries for operation (not included).Product features and decorations may vary from the pictures above.

Discover what’s possible™…www

.fisher-pri

ce.com

InstructionsProduct Number: 73408

™

2

Activity Ring(In Folded Position)

Center Track

Track A

Ball Director(Front Half)

Ball Director(Back Half)

Parts

Support R

#8 x 3/4"Screw - 4#10 x 21/8" Shoulder Bolt - 4

FASTENERS SHOWN ACTUAL SIZE

#6 x 1/2"Screw - 6#10 x 25/8" Screw - 4

Support L

Track C Track DTrack B

Bottom Track LB Bottom Track RBTop Rail LT Top Rail RT

Mirror Tray Ball 6 Balls

• Locate the battery compartment door on the bottom ofthe activity ring.

• Loosen the screw in the battery compartment door witha Phillips screwdriver.

• Remove the battery compartment door.• Insert three "C" (LR14) alkaline batteries, as indicated

inside the battery compartment.Hint: We recommend using alkaline batteries for longer life.• Close the battery compartment door and tighten the

screw with a Phillips screwdriver. Do not over-tighten.• When sounds or lights from this toy become faint or

stop, it’s time for an adult to change the batteries!

• Do not mix old and new batteries.• Do not mix different types of batteries: alkaline, standard

(carbon-zinc) or rechargeable (nickel-cadmium).• Remove the batteries during long periods of non-use.

Always remove exhausted batteries from the toy. Batteryleakage and corrosion can damage this toy. Dispose ofbatteries safely.

• Do not dispose of batteries in a fire. The batteries mayexplode or leak.

• Never short circuit the battery terminals.• Non-rechargeable batteries are not to be recharged.• Only batteries of the same or equivalent type as

recommended in the "Battery Installation" instructionsare to be used.

• If removable rechargeable batteries are used, they areonly to be charged under adult supervision.

• Rechargeable batteries are to be removed from the toybefore they are charged.

• If you use a battery charger, it should be examined regularly for damage to the cord, plug, enclosure andother parts. Do not use a damaged battery charger untilit has been properly repaired.

Battery CompartmentDoor

Bottom View

Activity Ring

3

1.5V x 3“C” (LR14)

SHOWN ACTUAL SIZE

Battery Installation Battery Tips

Consumer Information

Questions? We'd like to hear from you! Call Fisher-Price® Consumer Relations,

toll-free at 1-800-432-KIDS,8 AM - 6 PM EST Monday through Friday. Hearing-

impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to:

Fisher-Price® Consumer Relations, 636 Girard Avenue, East Aurora, New York 14052.

For other countries, outside the United States:Canada: call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.Great Britain: telephone 01628 500303.Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.

• Locate the ball director fronthalf (with the Fisher-Price®

logo on it). Note the labelingon the ball director front half(A, B, C and D).

• Fit the end of track A onto theball director peg labeled A. Besure to push the track all theway onto the peg.

• Repeat this procedure toattach tracks B, C and D tothe ball director front half.


• Fit the ball director back half onto the ball director fronthalf, as shown.

• Insert six #6 x 1/2" screws through the holes in the balldirector back half and into the ball director front half.Tighten the screws with a Phillips Screwdriver.Do not over-tighten.

11 22

4

Assembly

#6 x 1/2" Screw Shown Actual Size

B

A

D

C

Peg

Ball Director(Back Half)

C

D B

A

Chute

CAUTION

This product contains small parts in its unassembled state. Adult assembly is required.


• Place the bottom track RB on a flat surface with theRB facing you.

• Insert the tabs on the ends of the mirror tray into thegrooves in the bottom track RB.

44

5

Mirror Tray

Assembly

BottomTrack RB RB Marking

• Place the center track on a flat surface.IMPORTANT! Position the ball director assembly overthe center track so that the curves in the tracks matchthe curve in the center track.• Insert and "snap" the tabs on the bottom of the ball

director assembly into the slots in the center track.• Pull up on the ball director assembly to be sure it is

secure in the center track.• Set this assembly aside for assembly step 8.

33 Ball DirectorAssembly

CenterTrack

Tabs

Slots

RB

• Locate the top rail RT.• Slide the top rail RT onto the bottom track RB.• Insert two #10 x 2 3/4" screws through the holes in the

top rail RT and into the bottom track RB.• Tighten the screws with a Phillips screwdriver.

Do not over-tighten.• Set this assembly aside for assembly step 8.

55 Top Rail RTRT


• Place the bottom track LB on a flat surface with the LBfacing you.

• Slide the top rail LT onto the bottom track LB.• Insert two #10 x 2 3/4" screws through the holes in the

top rail LT and into the bottom track LB.• Tighten the screws with a Phillips screwdriver.

Do not over-tighten.

66


LB

LT

Top Rail LT

Bottom Track LB

6

Assembly

Bottom Track RB

RB

LB

7

8877

Assembly

• Position the side assembly labeled RT so that it curvestoward you.

• Hold the ball director assembly so that the Fisher-Price®

logo faces you. Note that the curve in both these partsform a half circle.

• Fit the ball director bottom tab and tracks A and B into theholes and slot in the side assembly. Push the two partstogether until they “snap” in place.

• Pull both parts apart to be sure they are secured together.• Repeat this procedure to attach the side assembly

labeled LT to the other side of the ball director assembly.

Side Assembly

RT

Hole

Hole

Slot

Tab


Side Assembly

Support L

• Turn the side assembly around so that it curves awayfrom you

• Fit the support L to the side assembly labeled LT.• Insert two #8 x 3/4" screws through the holes in support L

and into the side assembly LT. Tighten the screws with a Phillips screwdriver. Do not over-tighten.

• Repeat this procedure to attach support R to the sideassembly labeled RT.

LT

Track A

Logo

Track B

Ball DirectorAssembly

8

99 1010

Assembly

• Press both side latches on the activity ring and lift thering until it “clicks” (A).

• Press both latches again and lower the ring until it“clicks” in place as shown (B).

LatchActivity Ring

• Position the activity ring over the base assembly so thatthe speaker is over the chute.

• Fit the activity ring onto the base assembly.

Latch

Speaker

Chute

Activity Ring

Base Assembly

A

B

Assembly

9

• Insert two #10 x 2 1/8" shoulder bolts through the activityring and into the base assembly as shown. Tighten thebolts with a Phillips screwdriver. Do not over-tighten.

1111

#10 x 21/8" Shoulder BoltShown Actual Size

• Insert two #10 x 2 1/8" shoulder bolts through the baseassembly and into the activity ring. Tighten the bolts witha Phillips screwdriver. Do not over-tighten.

1212

1313

• Locate the tab on the back of ball director chute.• Push the tab on the ball director chute until it “snaps”

into place in the slot in the activity ring.

1414

• Lay the product on its side with the ball director facing you.

• Locate the tab on the ball director (above the Fisher-Price® logo).

• Push and "snap" the tab on the ball director chute until itsnaps into place in the activity ring.

• Turn the assembly upright.• Pull up on the activity ring to be sure the tabs are in place.

Back View

Slot

Tab

Inside View

Slot

Tab

PUSH

PUSH

Ball DirectorChute

Activity Ring

Ball DirectorChute

Activity Ring

10

Standing ModeThis mode is designed for babies who are walking and standing. To convert this toy to standing mode: Press bothlatches on the activity ring and lift the ring until it "clicks" into place. Push on the activity ring to be sure it is secure in itsupright position.

Ball - Insert the tab on the end ofthe ball strap up through the slot inthe activity ring (as shown). Pulldown on the ball to be sure thestrap is secure to the activity ring.

• Locate the power/mode switch on the activity ring andset it to standing position .

Wheel - Spin the wheelto start the music andlights or change the song.

Spinner – Rotatethe spinner fast orslow and the lightsand music chasealong at baby’s pace.

Ball – Baby bats theball to activate soundeffects and lights.

Latch - Press bothlatches to convert thistoy to standing mode.

Power / Mode Switch

• To turn power off, slide the power/mode switch to .Hint: If your child is not actively playing with this toy, itturns off automatically after a few minutes (sleep mode).

Ball Chute – Placea ball in the chute.

Dial – Turn the dial to makethe ball drop and roll alongthe tracks while lights flashand music plays.

Activity Ring - Lift for standing mode.

11

Crawling Mode

This mode is designed for babies who are crawling, sitting and learning to pull themselves up. To convert this toyto crawling mode: Press both side latches on the activity ring. Now, lower the activity ring until it "clicks" into place. Pull upon the activity ring to be sure it is secure.

Power / Mode Switch

• Locate the Power/Mode switch on the activity ring andset it to crawling position .

• To turn power off, slide the power/mode switch to .Hint: If your child is not actively playing with this toy, itturns off automatically after a few minutes (sleep mode).

Automatic Lights and Music –When baby crawls under theactivity ring sensor, lights andmusic start up automatically towelcome baby!

Wheel - Spin the wheel tostart the music and lightsor change the song.

Ball Chute – Placea ball in the chute.

Spinner – Rotate the spinner fastor slow and the lights and musicchase along at baby’s pace.

Ball – Baby bats the ballto activate sound effectsand lights.

Latch - Press bothlatches to convert thistoy to crawling mode.

Inflate the ball. Insert the tab on the endof the ball strap through the slot in theactivity ring (near the hub). Pull down onthe ball to be sure the strap is secure tothe activity ring.

Attach HereHub

Inside View

Dial – Turn the dial to makethe ball drop and roll alongthe tracks while lights flashand music plays.

Activity Ring - Lower forcrawling mode.

• Periodically check all screws and tighten as required.Check plastic parts for cracks or broken pieces.

• Wipe this toy with a clean cloth dampened with a mildsoap and water solution. Do not immerse this toy.

• This toy has no consumer serviceable parts. Do nottake this toy apart.

Note: This equipment has been tested and found to com-ply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interferencein a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions,may cause harmful interference to radio communications.However, there is no guarantee that interference will notoccur in a particular installation. If this equipment doescause harmful interference to radio or television reception,which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interfer-ence by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and

receiver.• Consult the dealer or an experienced radio/TV techni-

cian for help.CAUTION: Changes or modifications not expresslyapproved by the manufacturer responsible for compliancecould void the user's authority to operate the equipment.

Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. ©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

Printed in Mexico73408c-0920

Care

FCC Note(United States Only)

The automatic lights and music sensor on this productis activated by contrast in lighting. If the product is notturned off after use, changes in lighting conditions near thetoy may cause lights and music to start. When the prod-uct is not in use, please slide the power/mode switchto the off position.Hint: This product will not function properly in a dimly lit ordark room.

The automatic lights and music sensor on this prod-uct is also activated by contrast in colors. If your childis wearing clothing similar in color or tone to your flooring,contrast may not be sufficient to activate the lights andmusic. Please be sure that your child’s clothing is signifi-cantly lighter or darker than your flooring for proper activa-tion of automatic lights and music.

Sensor

Notice about Automatic Lightsand Music in Crawling Mode

Documents

Crawl & Cruise PlaygrPlaygroundound - Mattel...Crawl & Cruise PlaygrPlaygroundound Please keep this instruction sheet for future reference, as it contains important information. Adult