Upload
javier-arias-lucero
View
106
Download
10
Tags:
Embed Size (px)
Citation preview
SERVICE MANUAL LEVEL 2
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
ADJUSTMENTS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
ADJUSTMENTS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision HistoryRevision History
On the VC-281 boardThis service manual provides the information that is premised the circuit board replacement service and not intended repairinside the VC-281 board.Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the VC-281board are not shown.The following pages are not shown.
Schematic diagram .............................Pages 4-37 to 4-68Printed wiring board ............................Pages 4-89 to 4-92Waveforms ........................................... Pages 4-96 to 4-97
Mounted parts location ........................ Pages 4-100 to 4-101Electrical parts list ............................... Pages 6-20 to 6-26
Ver 1.0 2002. 04
DCR-TRV24E/TRV25E/TRV27E
RMT-814
AEP ModelNorth European Model
DCR-TRV24E/TRV25E/TRV27E
UK ModelDCR-TRV25E
E ModelEast European Model
Hong Kong ModelAustralian Model
Chinese ModelDCR-TRV25E/TRV27E
Tourist ModelDCR-TRV27E
DIGITAL VIDEO CAMERA RECORDER
Photo: DCR-TRV24E
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (992995441.pdf).• For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL ADJUSTMENT MANUAL
J MECHANISM ” (9-929-807-11).
J MECHANISM
— 2 —
DCR-TRV24E/TRV25E/TRV27E
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
COVERCOVER
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
Video camerarecorder
System
Video recording system2 rotary headsHelical scanning systemAudio recording systemRotary heads, PCM systemQuantization: 12 bits (Fs 32 kHz,stereo 1, stereo 2), 16 bits(Fs 48 kHz, stereo)Video signalPAL colour, CCIR standardsUsable cassetteMini DV cassette with the mark printedTape speedSP: Approx. 18.81 mm/sLP: Approx. 12.56 mm/sRecording/playback time(using cassette DVM60)SP: 1 hourLP: 1.5 hoursFastforward/rewind time(using cassette DVM60)When using the battery pack:Approx. 2 min. and 30 secondsWhen using the AC power adaptor:Approx. 2 min. and 30 secondsViewfinderElectric viewfinder (colour)Image device3.8 mm (1/4.7 type) CCD (ChargeCoupled Device)Gross: Approx. 1 070 000Effective (still):Approx. 1 000 000 pixelsEffective (moving):Approx. 690 000 pixelsLensCarl ZeissCombined power zoom lensFilter diameter30 mm (1 3/16 in.)10 (Optical), 120 (Digital)
Focal length3.7 – 37 mm (5/32 – 1 1/2 in.)When converted to a 35 mm stillcameraIn CAMERA:50 – 500 mm (2 – 19 3/4 in.)In MEMORY:42 – 420 mm (1 11/16 – 16 5/8 in.)Colour temperatureAuto, HOLD (Hold), nIndoor(3 200 K), Outdoor (5 800 K)Minimum illumination7 lx (lux) (F 1.8)0 lx (lux) (in the NightShot mode)** Objects unable to be seen due to
the dark can be shot with infraredlighting.
Input/Output connectors
S video input/outputDCR-TRV25E/TRV27E4-pin mini DINLuminance signal: 1 Vp-p, 75 Ω(ohms), unbalancedChrominance signal: 0.3 Vp-p,75 Ω (ohms), unbalancedS video outputDCR-TRV24E:4-pin mini DINLuminance signal: 1 Vp-p, 75 Ω(ohms), unbalancedChrominance signal: 0.3 Vp-p,75 Ω (ohms), unbalancedAudio/Video input/outputDCR-TRV25E/TRV27EAV MINI JACK, 1 Vp-p, 75 Ω(ohms), unbalanced, sync negative327 mV, (at output impedancemore than 47 kΩ (kilohms))Output impedance with less than2.2 kΩ (kilohms)/Stereo minijack(ø 3.5mm)Input impedance more than47 kΩ (kilohms)Audio/Video outputDCR-TRV24E:AV MINI JACK, 1 Vp-p, 75 Ω(ohms), unbalanced, sync negative327 mV, (at output impedancemore than 47 kΩ (kilohms))Output impedance with less than2.2 kΩ (kilohms)/Stereo minijack(ø 3.5mm)Input impedance more than47 kΩ (kilohms)
DV input/outputDCR-TRV25E/TRV27E4-pin connectorDV outputDCR-TRV24E:4-pin connectorHeadphone jackStereo minijack (ø 3.5 mm)USB jackmini-BLANC jackStereo mini-minijack (ø 2.5 mm)MIC jackStereo minijack (ø 3.5 mm)
LCD screen
PictureDCR-TRV24E/TRV25E6.2 cm (2.5 type)50.3 × 37.4 mm (2 × 1 1/2 in.)DCR-TRV27E:8.8 cm (3.5 type)72.2 × 50.4 mm (2 7/8 × 2 in.)Total dot number123 200 (560 × 220)
General
Power requirements7.2 V (battery pack)8.4 V (AC power adaptor)Average power consumption(when using the battery pack)During camera recording usingLCDDCR-TRV24E/TRV25E: 4.1 WDCR-TRV27E: 4.5 WViewfinder3.3 WOperating temperature0°C to 40°C (32°F to 104°F)Storage temperature–20°C to + 60°C(–4°F to + 140°F)Dimensions (Approx.)76 × 93 × 163 mm(3 × 3 3/4 ×6 1/2 in.)(w/h/d)Mass (approx.)DCR-TRV24E/TRV25E:640 g (1 lb 6 oz)DCR-TRV27E: 660 g (1 lb 7 oz)main unit onlyDCR-TRV24E/TRV25E:740 g (1 lb 10 oz)DCR-TRV27E: 760 g (1 lb 10 oz)including the battery packcassette DVM60 and lens capSupplied accessoriesSee page 3.
AC power adaptor
Power requirements100 – 240 V AC, 50/60 HzPower consumption23 WOutput voltageDC OUT: 8.4 V, 1.5 A in theoperating modeOperating temperature0°C to 40°C (32°F to 104°F)Storage temperature–20°C to + 60°C (–4°F to + 140°F)Dimensions (approx.)125 × 39 × 62 mm(5 × 1 9/16 × 2 1/2 in.) (w/h/d)excluding projecting partsMass (approx.)280 g (9.8 oz)excluding mains lead
Battery pack
NP-FM50Maximum output voltageDC 8.4 VOutput voltageDC 7.2 VCapacity8.5 Wh (1 180 mAh)Dimensions (approx.)38.2 × 20.5 × 55.6 mm(1 9/16 × 13/16 × 2 1/4 in.)(w/h/d)Mass (approx.)76 g (2.7 oz)TypeLithium ion
“Memory Stick”MemoryFlash memory8 MB: MSA-8AOperating voltage2.7 – 3.6 VPower consumptionApprox. 45 mA in the operatingmodeApprox. 130 µA in the standbymodeDimensions (approx.)50 × 2.8 × 21.5 mm(2 × 1/8 × 7/8 in.) (w/h/d)Mass (approx.)4 g (0.14 oz)
Design and specifications aresubject to change without notice.
— 3 —
DCR-TRV24E/TRV25E/TRV27E
1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.
2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.
5. Check the B+ voltage to see it is at the values specified.6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚Cduring repairing.
• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).
• Be careful not to apply force on the conductor when solderingor unsoldering.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!
• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1Wireless Remote Commander (1)
2AC-L10A/L10B/L10C AC power adaptor (1),Mains lead (1)
3 R6 (size AA) battery for RemoteCommander (2)
4 Battery pack (1)NP-FM50
(DCR-TRV27E: JE model only)
(DCR-TRV24E: AEP, NE model only)(DCR-TRV25E: AEP, UK, EE, NE model only)(DCR-TRV27E: AEP, EE, NE model only)
5A/V connecting cable (1)
6 Shoulder strap (1)
7 Lens cap (1)
8 “Memory Stick” (MSA-8A) (1)
9USB cable (1)
0 CD-ROM (SPVD-008 USB Driver) (1)
qa 21-pin adaptor (1)
qs 2-pin conversion adaptor (1)
(DCR-TRV25E: E, HK/TRV27E: E, HK model only)qd 2-pin conversion adaptor (1)
8
1 2
4 75 6
3
9
qs qd
0 qa
• SUPPLIED ACCESSORIESMake sure that the following accessories are supplied with your camcorder.
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong modelAUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV24E
AEP, NE
Table for difference of function
Model
Destination
Line REC
LCD
DCR-TRV25E
AEP, UK, NE, EE, E,HK, AUS, CH
a
DCR-TRV27E
AEP, NE, EE, E, HK,AUS, CH, JE
a
3.5inch2.5inch
— 4 —
DCR-TRV24E/TRV25E/TRV27E
TABLE OF CONTENTS1. SERVICE NOTE1-1. SERVICE NOTE ·····························································1-11. POWER SUPPLY DURING REPAIRS ·························· 1-12. TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ·····························································1-11-2. SELF-DIAGNOSIS FUNCTION ····································1-21. SELF-DIAGNOSIS FUNCTION ····································1-22. SELF-DIAGNOSIS DISPLAY ······································· 1-23. SERVICE MODE DISPLAY ·········································· 1-23-1. Display Method ······························································· 1-23-2. Switching of Backup No. ················································1-23-3. End of Display ·································································1-24. SELF-DIAGNOSIS CODE TABLE ································1-3
2. DISASSEMBLY2-1. LCD SECTION (PD-161 BOARD) ································2-32-2. EVF SECTION (LB-077 BOARD) ·································2-42-3. FRONT PANEL SECTION ·············································2-52-4. MA-409, FB-219 BOARDS ············································2-62-5. TOP CABINET ASSEMBLY ·········································2-72-6. CABINET (R) SECTION ··············································· 2-72-7. BATTERY PANEL SECTION ········································2-82-8. EVF SECTION ································································2-82-9. LB-077 BOARD ······························································ 2-92-10. VA-117 BOARD (1) ······················································2-102-11. MAIN CHASSIS COMPLETE ASSEMBLY ···············2-112-12. VA-117 BOARD (2) ······················································2-122-13. VC-281 BOARD ···························································2-122-14. LENS SECTION ···························································2-132-15. MECHANISM DECK ···················································2-132-16. JK-217, JK-218 BOARDS ············································2-142-17. CD-366 BOARD, 750A (CZ) BLOCK ASSEMBLY
(LENS DEVICE) ···························································2-142-18. CK-108 BOARD ···························································2-172-19. HINGE ASSEMBLY ·····················································2-182-20. CONTROL SWITCH BLOCK (PS-CX2670) ·············· 2-192-21. MEMORY STICK CONNECTOR ·······························2-202-22. CIRCUIT BOARDS LOCATION ·································2-212-23. FLEXIBLE BOARDS LOCATION ······························2-22
3. BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM (1/4) ··························· 3-13-2. OVERALL BLOCK DIAGRAM (2/4) ··························· 3-33-3. OVERALL BLOCK DIAGRAM (3/4) ··························· 3-53-4. OVERALL BLOCK DIAGRAM (4/4) ··························· 3-73-5. POWER BLOCK DIAGRAM (1/3) ································3-93-6. POWER BLOCK DIAGRAM (2/3) ······························3-113-7. POWER BLOCK DIAGRAM (3/3) ······························3-13
4. PRINTED WIRING BOARDS ANDSCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3) ······················· 4-1FRAME SCHEMATIC DIAGRAM (2/3) ······················· 4-3FRAME SCHEMATIC DIAGRAM (3/3) ······················· 4-5
4-2. SCHEMATIC DIAGRAMS ············································4-9• CD-366 (CCD IMAGER)
SCHEMATIC DIAGRAM ······························ 4-9• LB-077 (EVF, EVF BACK LIGHT)
SCHEMATIC DIAGRAM ····························4-10• MA-409 (MIC IN, HP JACK, REMOTE CONTROLRECEIVER, SWITCH)
SCHEMATIC DIAGRAM ····························4-11• FB-219 (MANUAL FOCUS SENSOR)
SCHEMATIC DIAGRAM ····························4-11• JK-217 (STEADY SHOT, A/D IN/OUT)
SCHEMATIC DIAGRAM ····························4-13
• JK-218 (DIGITAL IN/OUT)SCHEMATIC DIAGRAM ····························4-13
• CK-108 (SWITCH, CONNECTOR)SCHEMATIC DIAGRAM ····························4-15
• CONTROL SWITCH BLOCK (PS-CX2670)SCHEMATIC DIAGRAM ····························4-17
• PD-161 (1/2)(RGB DRIVE, TIMING GENERATOR)SCHEMATIC DIAGRAM ····························4-19
• PD-161 (2/2)(LCD DRIVE, BACK LIGHT)SCHEMATIC DIAGRAM ····························4-21
• VA-117 (1/6)(RGB DRIVE, TG)SCHEMATIC DIAGRAM ····························4-23
• VA-117 (2/6)(AUDIO)SCHEMATIC DIAGRAM ····························4-25
• VA-117 (3/6)(MIC AMP)SCHEMATIC DIAGRAM ····························4-27
• VA-117 (4/6)(DC-DC CONVERTER)SCHEMATIC DIAGRAM ····························4-29
• VA-117 (5/6)(CHARGE)SCHEMATIC DIAGRAM ····························4-31
• VA-117 (6/6)(VIDEO I/O)SCHEMATIC DIAGRAM ····························4-33
• FP-100 (MODE SWITCH), FP-228 (DEW SENSOR),FP-102 (TAPE TOP/END SENSOR, S/T REEL)
FLEXIBLE BOARDS ··································4-35
Shematic diagram of the VC-281 board are not shown.Pages from 4-37 to 4-68 are not shown.
4-3. PRINTED WIRING BOARDS ·····································4-71• CD-366 (CCD IMAGER)
PRINTED WIRING BOARD ·······················4-71• FP-443 FLEXIBLE BOARD ·····································4-72• JK-217 (STEADY SHOT, A/D IN/OUT)
PRINTED WIRING BOARD ·······················4-73• JK-218 (DIGITAL IN/OUT)
PRINTED WIRING BOARD ·······················4-74• MA-409 (MIC IN, HP JACK, REMOTE CONTROLRECEIVER, SWITCH)
PRINTED WIRING BOARD ·······················4-75• FP-444 FLEXIBLE BOARD ·····································4-76• FB-219 (MANUAL FOCUS SENSOR)
PRINTED WIRING BOARD ·······················4-77• PD-161 (RGB DRIVE, TIMING GENERATORLCD DRIVE, BACK LIGHT)
PRINTED WIRING BOARD ·······················4-78• LB-077 (EVF, EVF BACK LIGHT)
PRINTED WIRING BOARD ·······················4-79• FP-100 (MODE SWITCH), FP-228 (DEW SENSOR),FP-102 (TAPE TOP/END SENSOR, S/T REEL)
FLEXIBLE BOARD ·····································4-79• CK-108 (SWITCH, CONNECTOR)
PRINTED WIRING BOARD ·······················4-81• VA-117 (RGB DRIVE, TG, AUDIO, MIC AMP,DC-DC CONVERTER, CHARGE, VIDEO I/O)
PRINTED WIRING BOARD ·······················4-85
Printed wiring board of the VC-281 board are not shown.Pages from 4-89 to 4-92 are not shown.
4-4. WAVEFORMS ······························································4-93
Waveforms of the VC-281 board are not shown.Pages from 4-96 to 4-97 are not shown.
— 5 —
DCR-TRV24E/TRV25E/TRV27E
4-5. MOUNTED PARTS LOCATION ·································4-98
Mounted parts location of the VC-281 board is not shown.Pages from 4-100 to 4-101 are not shown.
5. ADJUSTMENTS1. Adjusting items when replacing main parts and boards. ·5-25-1. CAMERA SECTION ADJUSTMENT ···························5-41-1. PREPARATIONS BEFORE ADJUSTMENT
(CAMERA SECTION) ···················································5-41-1-1.List of Service Tools ························································5-41-1-2.Preparations ·····································································5-51-1-3.Precaution ········································································5-71. Setting the Switch ····························································5-72. Order of Adjustments ······················································5-73. Subjects ···········································································5-71-2. INITIALIZATION OF 8, A, B, C, D, E, F, 1B, 1E, 1F
PAGE DATA ····································································5-81-2-1. INITIALIZATION OF A, D PAGE DATA ······················5-91. Initializing the A, D Page Data ········································5-92. Modification of A, D Page Data ······································5-93. A Page Table ····································································5-94. D Page Table ·································································· 5-101-2-2. INITIALIZATION OF B, 1B PAGE DATA ·················· 5-111. Initializing the B, 1B Page Data ····································5-112. Modification of B, 1B Page Data ·································· 5-113. B Page Table ·································································· 5-114. 1B Page Table ································································5-111-2-3. INITIALIZATION OF 8, C PAGE DATA ·····················5-121. Initializing the 8, C Page Data ······································· 5-122. Modification of 8, C Page Data ·····································5-123. 8 Page Table ··································································· 5-124. C Page Table ·································································· 5-131-2-4. INITIALIZATION OF E, F, 1E, 1F PAGE DATA ········5-151. Initializing the E, F, 1E, 1F Page Data ·························· 5-152. Modification of E, F, 1E, 1F Page Data ·························5-153. E Page Table ·································································· 5-164. F Page Table ·································································· 5-175. 1E Page Table ································································5-186. 1F Page Table ································································5-191-3. CAMERA SYSTEM ADJUSTMENTS ························5-201. 54MHz Origin Oscillation Adjustment (VC-281 board) · 5-202. HALL Adjustment ·························································5-213. MR Adjustment ·····························································5-224. Flange Back Adjustment (Using Minipattern Box) ······· 5-235. Flange Back Adjustment (Using Flange Back
Adjustment Chart and Subject More Than 500m Away) · 5-245-1. Flange Back Adjustment (1) ·········································· 5-245-2. Flange Back Adjustment (2) ·········································· 5-246. Flange Back Check ························································5-257. MAX GAIN Adjustment ··············································· 5-258. Picture Frame Setting ····················································5-269. Color Reproduction Adjustment ····································5-2710. Auto White Balance & LV Standard Data Input ··········· 5-2711. Auto White Balance Adjustment ··································· 5-2812. White Balance Check ····················································5-2913. Mechanical Shutter Adjustment ····································5-3014. Black Defective CCD Adjustment ·································5-3015. Steady Shot Check ·························································5-311-4. COLOR ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENT ·····························································5-321. VCO Adjustment (VA-117 board) ·································5-322. RGB AMP Adjustment (VA-117 board) ························5-333. Contrast Adjustment (VA-117 board) ····························5-334. White Balance Adjustment (VA-117 board) ·················· 5-341-5. LCD SYSTEM ADJUSTMENT ··································· 5-351. VCO Adjustment (PD-161 board) ·································5-35
2. RGB AMP Adjustment (PD-161 board) ························5-363. Contrast Adjustment (PD-161 board) ····························5-364. COM AMP Adjustment (PD-161 board) ·······················5-375. V COM Adjustment (PD-161 board) ····························5-376. White Balance Adjustment (PD-161 board) ·················· 5-385-2. MECHANISM SECTION ADJUSTMENT ·················5-392-1. HOW TO ENTER RECORD MODE WITHOUT
CASSETTE ···································································5-392-2. HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETTE ···································································5-392-3. TAPE PATH ADJUSTMENT ········································5-391. Preparation for Adjustment ···········································5-392. Processing after Completing Operations: ······················ 5-395-3. VIDEO SECTION ADJUSTMENTS ···························5-403-1. PREPARATIONS BEFORE ADJUSTMENTS ············5-403-1-1.Equipment Required ······················································ 5-403-1-2.Precautions on Adjusting ···············································5-413-1-3.Adjusting Connectors ····················································5-423-1-4.Connecting the Equipment ············································5-423-1-5. Alignment Tapes ···························································5-433-1-6. Input/Output Level and Impedance ······························ 5-433-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········5-441. Initialization of 8, A, B, C, D, E, F, 1B, 1E, 1F
Page Data ·······································································5-442. Serial No. Input ·····························································5-442-1. Company ID Input ·························································5-442-2. Serial No. Input ·····························································5-443-3. SERVO AND RF SYSTEM ADJUSTMENT ···············5-461. Cap FG Duty Adjustment (VC-281 board) ···················5-462. PLL f0 & LPF f0 Adjustment (VC-281 board) ·············· 5-463. Switching Position Adjustment (VC-281 board) ···········5-474. AGC Center Level and APC & AEQ Adjustment ·········5-474-1. Preparations before adjustments ····································5-474-2. AGC Center Level Adjustment (VC-281 board) ···········5-474-3. APC & AEQ Adjustment (VC-281 board) ····················5-484-4. Processing after Completing Adjustments ····················5-485. PLL f0 & LPF f0 Fine Adjustment (VC-281 board) ······ 5-493-4. VIDEO SYSTEM ADJUSTMENTS ·····························5-501. Chroma BPF f0 Adjustment (VA-117 board) ·················5-502. S VIDEO OUT Y Level Adjustment (VC-281 board) ···5-503. S VIDEO OUT Chroma Level Adjustment
(VC-281 Board) ·····························································5-514. VIDEO OUT Y, Chroma Level Check (VC-281 board) · 5-513-5. AUDIO SYSTEM ADJUSTMENTS ····························5-521. Playback Level Check ···················································5-532. Overall Level Characteristics Check ·····························5-533. Overall Distortion Check ···············································5-534. Overall Noise Level Check ············································5-535. Overall Separation Check ·············································· 5-535-4. SERVICE MODE ·························································· 5-544-1. ADJUSTMENT REMOTE COMMANDER ················5-541. Using the adjustment remote commander ·····················5-542. Precautions upon using the adjustment remote
commander ····································································5-544-2. DATA PROCESS ···························································5-554-3. SERVICE MODE ·························································· 5-561. Setting the Test Mode ····················································5-562. Emergence Memory Address ········································5-562-1. EMG Code (Emergency Code) ·····································5-562-2. MSW Code ····································································5-573. Bit value discrimination ················································5-584. Switch check (1) ····························································5-585. Switch check (2) ····························································5-586. Switch check (3) ····························································5-597. Switch check (4) ····························································5-598. Record of Use check (1) ················································5-609. Record of Use check (2) ················································5-6010. Record of Self-diagnosis check ·····································5-60
— 6 —
DCR-TRV24E/TRV25E/TRV27E
6. REPAIR PARTS LIST6-1. EXPLODED VIEWS ······················································ 6-16-1-1.OVERALL ······································································ 6-16-1-2.FRONT PANEL SECTION ·············································6-26-1-3.CABINET (R) SECTION ··············································· 6-36-1-4.LCD SECTION (2.5INCH) (TRV24E/TRV25E) ············ 6-46-1-5.LCD SECTION (3.5INCH) (TRV27E) ··························· 6-56-1-6.EVF SECTION ································································6-66-1-7.MAIN CHASSIS COMPLETE SECTION ·····················6-76-1-8.CABINET (L) SECTION ················································6-86-1-9.CASSETTE COMPARTMENT ASSEMBLY,
DRUM BLOCK ASSEMBLY ·········································6-96-1-10. LS CHASSIS BLOCK ASSEMBLY ·························· 6-106-1-11. MECHANISM CHASSIS BLOCK ASSEMBLY ······ 6-116-2. ELECTRICAL PARTS LIST ········································6-12
Parts list of the VC-281 board are not shown.Pages from 6-20 to 6-26 are not shown.
* Color reproduction frame is shown on page 191.
1-1
DCR-TRV24E/TRV25E/TRV27E
SECTION 1SERVICE NOTE
COVERCOVER
1-1. SERVICE NOTE1. POWER SUPPLY DURING REPAIRSIn this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off sothat the unit cannot operate.This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1:Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
Method 1:Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)1 Refer to 2-3 to remove the front panel assembly.2 Refer to 2-5 to remove the top cabinet assembly.3 Refer to 2-6 to remove the cabinet (R) assembly.4 Refer to 2-7 to remove the battery panel section.5 Remove the EVF block.6 Open the VA-117 board.7 Disconnect CN1010 (27P, 0.3mm) of VC-281 board.8 Open the cassette lid.9 Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
VC-281 board
DC power supply(+ 4.5V)
Loading motor
CN1010
1-2
DCR-TRV24E/TRV25E/TRV27E
1-2. SELF-DIAGNOSIS FUNCTION1. SELF-DIAGNOSIS FUNCTIONWhen problems occur while the unit is operating, the self-diagnosisfunction starts working, and displays on the viewfinder, LCD screenor LCD window what to do. This function consists of two display;self-diagnosis display and service mode display.Details of the self-diagnosis functions are provided in the Instructionmanual.
Note: The “self-diagnosis display” data will be kept even if the lithium battery (CK-108 board BT5201 of the cabinet (R) assembly) is removed.
2. SELF-DIAGNOSIS DISPLAYWhen problems occur while the unit is operating, the counter of theviewfinder, LCD screen or LCD window consists of an alphabetand 4-digit numbers, which blinks at 3.2 Hz. This 5-character displayindicates the “repaired by:”, “block” in which the problem occurred,and “detailed code” of the problem.
3. SERVICE MODE DISPLAYThe service mode display shows up to six self-diagnosis codes shown in the past.
3-1. Display MethodWhile pressing the “STOP” key, set the switch from OFF to “VCR”, and continue pressing the “STOP” key for 5 seconds continuously. Theservice mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
3-2. Switching of Backup No.By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which theproblem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)[1] : Occurred first time [4] : Occurred fourth time[2] : Occurred second time [5] : Occurred fifth time[3] : Occurred third time [6] : Occurred the last time
3-3. End of DisplayTurning OFF the power supply will end the service mode display.
Order of previous errors
Backup No. Self-diagnosis Codes
C : 3 1 : 1 1[3]
Lights up
Viewfinder or LCD screen
[3] C : 3 1 : 1 1 3 C : 3 1 : 11LCD window
1 13 1
C : 3 1 : 11
C
Repaired by:
Refer to page 1-3.Self-diagnosis Code Table.
Indicates the appropriatestep to be taken.E.g.31 ....Reload the tape.32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2Hz
C : Corrected by customerH : Corrected by dealerE : Corrected by service
engineer
Viewfinder or LCD screen LCD window
C : 3 1 : 1 1
LCD window
Control dial
1-3E
DCR-TRV24E/TRV25E/TRV27E
4. SELF-DIAGNOSIS CODE TABLE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
BlockFunction
0 4
2 1
2 2
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
6 1
6 1
6 2
6 2
DetailedCode
0 0
0 0
0 0
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
0 0
1 0
0 0
0 1
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does notcomplete within specified time
UNLOAD direction. Loading does notcomplete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting therest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-out.
UNLOAD direction loading motortime-out.
T reel side tape slacking whenunloading.
Winding S reel fault when counting therest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drumoperations
Difficult to adjust focus(Cannot initialize focus.)
Zoom operations fault(Cannot initialize zoom lens.)
Steadyshot function does not work well.(With pitch angular velocity sensor outputstopped.)
Steadyshot function does not work well.(With yaw angular velocity sensor outputstopped.)
Self-diagnosis Code
Rep
aire
d by
:
Correction
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Inspect the lens block focus MR sensor (Pin 8, 9 of CN1301 ofVC-281 board) when focusing is performed when the focus ring isrotated in the focus manual mode, and the focus motor drive circuit(IC1301 of VC-281 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin qk, w; of CN1301 ofVC-281 board) when zooming is performed when the zoom lens isoperated and the zoom motor drive circuit (IC1301 of VC-281board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE5302 of JK-217 board)peripheral circuits.
Inspect yaw angular velocity sensor (SE5301 of JK-217 board)peripheral circuits.
2-1
SECTION 2DISASSEMBLY
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
The following flow chart shows the disassembly procedure.D
CR
-TR
V24
E/T
RV
25E
/TR
V27
E
2-1. LCD section (PD-161 board)
2-2. EVF section (LB-077 board)
2-3. Front panel section
2-5. Top cabinet assembly
(page 2-4)
(page 2-5)
(page 2-7)
2-6. Cabinet (R) section (page 2-7)
2-7. Battery panel section (page 2-8)
2-8. EVF section (page 2-8)
2-10. VA-117 board (1) (page 2-10)
2-12. VA-117 board (2) (page 2-12)
2-16. JK-217, JK-218 boards (page 2-14)
2-17. CD-366 board, 750A (CZ) block assembly (Lens device) (page 2-14)
2-14. Lens section (page 2-13)
2-18. CK-108 board (page 2-17)
2-19. Hinge assembly (page 2-18)
2-20. Control switch block (PS-CX2670)
2-21. Memory stick connector (page 2-20)
(page 2-19, 2-20)
2-13. VC-281 board (page 2-12)
2-11. Main chassis complete assembly
(page 2-11)
(page 2-3) (page 2-3)
(page 2-5)
(page 2-6)
(page 2-6)
PD-161 board service position
LB-077 board service position
MA-409 board service position
(page 2-10)VA-117 board service position
2-4. MA-409, FB-219 boards
(page 2-9)2-9. LB-077 board
(page 2-15)
(page 2-13)
(page 2-16)
2-15. Mechanism deck
Service position to check the VTR section
Service position to check the Camera section
2-2
DCR-TRV24E/TRV25E/TRV27E
Adjustment remotecommander (RM-95)
AC poweradaptor AC IN
CPC-8 jig(J-6082-388-A)
CPC lid
[CONNECTION OF EQUIPMENT]
Screw(M1.7 × 4), lock ace, p2
2-3
DCR-TRV24E/TRV25E/TRV27E
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD SECTION (PD-161 BOARD)
PD-161
PD-161
B
B
A
A
1 Screw (M2 × 4), lock ace, p2
2 Screw (M2 × 4), lock ace, p2
5 P cabinet (M)
7 P cabinet (C) assembly, Indication LCD block assembly
P cabinet (C) assembly
3 Two screws (M2 × 4), lock ace, p2
[PD-161 BOARD SERVICE POSITION]
4 Five claws
6 FP-441 flexible board (Indication LCD block assembly) (20P)
Indication LCDblock assembly
FP-441 flexible board8 Liquid crystal indicator module
Liquid crystalindicator module
9 Cold cathode fluorescent tube
Cold cathode fluorescent tube
q; PD-161 board, P frame assembly
PD-161 board
The 7 P cabinet (C) assembly is securely fixed in the LCD unit by the five 4 claws. Because the Indication LCD block assemblyinstalled in the Cabinet (C) assembly is connected to the PD-161 board with theFP-441 flexible board, the flexible boardmay be damaged if the Cabinet (C) assembly is removed forcibly. Be careful notto damage the flexible board.
Caution
Caution
CPC-8 jig(J-6082-388-A)
Adjustment remotecommander (RM-95)
AC poweradaptor
AC IN
2-4
DCR-TRV24E/TRV25E/TRV27E
2-2. EVF SECTION (LB-077 BOARD)
B A
2 Two tapping screws (M1.7 × 6)
4 VF cabinet (upper) assembly
6 VF lens assembly
7 LB-077 board, Lamp guide
5 Three clawsPrism sheet
Illuminator
3Two claws
q; LB-077 board
9 Lamp guide
8 Two claws
1 Raise the EVF in the direction of the arrow A and slide it in the direction of the arrow B.
When separating the 7 LB-077 board and Lamp guide from the 6 VF lens assembly by removing the three 5 claws, do not face the side of the VF lens assembly on which the LB-077 board is installed, downwards. Because the Illuminator and others may fall out of the VF lens assembly, hold the illuminator and others using tape or paper as shown to prevent them from falling. Be careful on this point especially when removing the LB-077 board and Lampguide because the three claws located in the VF lens assembly are easy to break.
Hold the illuminator and others using tape or paper as shown to prevent them from falling.
Caution
2-5
DCR-TRV24E/TRV25E/TRV27E
CPC-8 jig(J-6082-388-A)
[LB-077 BOARD SERVICE POSITION]
AC poweradaptor AC IN
VF lens assemblyLB-077 board
Adjustment remotecommander (RM-95)
1 Screw (M1.7 × 4), lock ace, p2
4 Screw (M1.7 × 4), lock ace, p2
2 Screw (M1.7 × 4), lock ace, p2
3 Open the jack cover assembly
5 Remove the Front panel section in the direction of the arrow.
7 Front panel section
Because the 7 Front panel section is connected to the main unit by the 6 FP-437 flexible board, the flexible board may be damaged if you remove the Front panel section forcibly. Be very careful not to damage the flexible board.
Caution
Caution
6 FP-437 flexible board (24P)
2-3. FRONT PANEL SECTION
2-6
DCR-TRV24E/TRV25E/TRV27E
2-4. MA-409, FB-219 BOARDS
1 Microphone (4P)
Route 1 the harness of the Microphoneunderneath the MA-409 board as shownin the illustration below.
Caution
MA-409 board
3 Tapping screw (M1.7 × 3.5)
5 Tapping screw (M1.7 × 3.5)
6 Focus button retainer
7 Focus button, FP-444 flexible board
Focus button
4 FB-219 board
8 MA-409 board
FB-219 board
MA-409 board
2 Screw (M1.7 × 2.5)
[MA-409 BOARD SERVICE POSITION]
FP-437 flexible board (24P)
AC poweradaptor AC IN
Adjustment remotecommander (RM-95)
2-7
DCR-TRV24E/TRV25E/TRV27E
2-5. TOP CABINET ASSEMBLY
2 Screw (M1.7 × 4), lock ace, p2
1 Move the EVF in the direction of the arrow.
3 Screw (M1.7 × 4), lock ace, p2
4 Claw
5 Top cabinet assembly
1 Screw (M1.7 × 4), lock ace, p2
2 Screw (M1.7 × 4), lock ace, p2
4 Screw (M1.7 × 4), lock ace, p2
3 Open the cassette lid
5 Remove the Cabinet (R) section in the direction of the arrow.
6 FP-434 flexible board (40P)
7 Cabinet (R) section
Because the 7 Cabinet (R) section is connected to the main unit using the 6 FP-434 flexible board, the flexible board may be damaged if you remove the Cabinet (R) section forcibly. Be very careful not to damage the flexible board.
Caution
2-6. CABINET (R) SECTION
2-8
DCR-TRV24E/TRV25E/TRV27E
2-7. BATTERY PANEL SECTION
VA-117
1 Screw (M1.7 × 4), lock ace, p2
3 Two screws (M1.7 × 4), lock ace, p2
1 Screw (M1.7 × 4), lock ace, p2
2 CPC lid
4 Open the cassette lid
5 Remove the Battery panel section in the direction of the arrow.
7 Battery panel section
6 Battery terminal board (6P)
2 Strap bracket (lower)
3 BT panel assembly
4 Battery terminal board
VA-117
VA-117
1 Screw (M1.7 × 2.5)
7 Screw (M1.7 × 2.5)
4 Peel off the tape.
5 Slide the EVF slightly in the direction of the arrow so that the two screws 6 become visible.
2 Screw (M1.7 × 2.5)
3 VA heat sink
6 Two tapping screws (M1.7 × 5)
8 FP-435 flexible board (20P)
9 EVF section
2-8. EVF SECTION
2-9
DCR-TRV24E/TRV25E/TRV27E
2-9. LB-077 BOARD
8
Prism sheet
Illuminator
When separating the q; LB-077 boardand Lamp guide from the qa VF lens assembly by removing the three 9 claws,do not face the side of the VF lens assembly on which the LB-077 board isinstalled, downwards. Because the Illuminator and others mayfall out of the VF lens assembly, hold the illuminator and others using tape or paper as shown to prevent them from falling. Be careful on this point especially when removing the LB-077 board and Lampguide because the three claws located in the VF lens assembly are easy to break.
Caution
Hold the illuminator and others using tape or paper as shown to prevent them from falling.
1 Screw (M1.7 × 2.5)
2 Claw
3 Flexible retainer metal sheet
4 VF flexible retainer sheet
5 Two tapping screws (M1.7 × 6)
6 Two claws
qs Two claws9 Three claws
7 VF cabinet (upper) assembly
q; LB-077 board, Lamp guide
qf LB-077 board
qd Lamp guideqa VF lens assembly
2-10
DCR-TRV24E/TRV25E/TRV27E
2-10.VA-117 BOARD (1)
VA-117
VC-281
1 FP-436 flexible board (20P)
(28P)
(12P)
2 FP-434 flexible board
5 VA-117 board
3 Three screws (M1.7 × 2.5)
4 Board to board connector (100P)
VC-281
VA-117
[VA-117 BOARD SERVICE POSITION ]To check the EVF circuit (IC4201 and IC4202), connect the LB-077 board to the VF lens assembly,and then set the camera to the "Forced EVF ON" mode.
Setting the “Forced EVF ON” mode
1) Select page: 0, address: 10, and set data: 00.2) Select page: 3, address: C4, and set data: 67.3) Select page: 3, address: C5, and set data: 01.
Exiting the “Forced EVF ON” mode
1) Select page: 0, address: 10, and set data: 00.2) Select page: 3, address: C4, and set data: 00.3) Select page: 3, address: C5, and set data: 00.
CPC-8 jig(J-6082-388-A)
AC poweradaptor AC IN
Adjustment remotecommander (RM-95)
Battery terminalboard (6P)
Extension cable (100P)(J-6082-352-A)
VA-117 board
LB-077 boardVF lensassembly
FP-435flexible board (20P)
2-11
DCR-TRV24E/TRV25E/TRV27E
2-11.MAIN CHASSIS COMPLETE ASSEMBLY
VA-117
VA-117
1 Control switch block (PS-CX2670) (20P)
4 Main chassis complete assembly
2 FP-443 flexible board (6P)
3 Two screws (M1.7 × 2.5)
2-12
DCR-TRV24E/TRV25E/TRV27E
2-12.VA-117 BOARD (2)
VA-117
VC-281
1 FP-436 flexible board (20P)
2 FP-434 flexible board
(28P)
(12P)
5 VA-117 board
3 Three screws (M1.7 × 2.5)
4 Board to board connector (100P)
2-13.VC-281 BOARD
VC-281
1 Flexible board (from lens block) (27P)
2 FP-440 flexible board (24P)
4 FP-445 flexible board (30P)
3 Two screws (M1.7 × 2.5)
5 VC-281 board
2-13
DCR-TRV24E/TRV25E/TRV27E
2-14.LENS SECTION
VC-281
1 Two screws (M1.7 × 2.5)
2 Lens section
1 Four screws (M1.4 × 1.5)
2 Mechanism deck
2-15.MECHANISM DECK
2-14
DCR-TRV24E/TRV25E/TRV27E
2-16.JK-217, JK-218 BOARDS
2 JK-218 board
4 JK-217 board
1 Two screws (M1.7 × 2.5)
3 Two screws (M1.7 × 2.5)
51 Screw (M1.7 × 2.5) 3 Two tapping
screws (M1.7 × 3.5)
2 Two tapping screws (M1.7 × 5)
4 Lens frame (G), External connector (Hot shoe)
2 CD heat sink, CD radiation sheet
1 FP-440 flexible board (27P)
3 Optical filter block
4 Seal rubber (W)
5 Remove the solderings
8 750A (CZ) block assembly (Lens device)
6 CCD block assembly
7 CD-366 board
2-17.CD-366 BOARD, 750A (CZ) BLOCK ASSEMBLY (LENS DEVICE)
2-15
DCR-TRV24E/TRV25E/TRV27E
VA-117
VC-281
[SERVICE POSITION TO CHECK THE VTR SECTION]Connection to Check the VTR SectionTo check the VTR section, set the VTR to the “Forced VTR power ON” mode.Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 02, and
press the PAUSE button of the adjustment remotecommander.
Exiting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander.4) Select page: 0, address: 01, and set data: 00.
To eject the cassette, connect Pin wd of the CN1501 on the VC-281 board to Pin w;(GND) of the CN1501 on the VC-281 boardfor a second.Note: Be sure to enter the "Forced VTR power ON" mode when ejecting the cassette.
CN15012
24 23
1
CPC-8 jig(J-6082-388-A)
AC poweradaptor AC IN
Adjustment remotecommander (RM-95)
Battery terminalboard (6P)
Extension cable (100P)(J-6082-352-A)
VA-117 board
VC-281 board
JK-217 board
JK-218 board
Mechanism deck
2-16
DCR-TRV24E/TRV25E/TRV27E
VA-117
VC-281
[SERVICE POSITION TO CHECK THE CAMERA SECTION]Connection to Check the Camera SectionTo check the CAMERA section, set the CAMERA to the “Forced camera power ON” mode.When you want to operate the ZOOM and FOCUS, use the controls on the remote commander (with HOLD switch off).
Setting the “Forced Camera Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 01, and
press the PAUSE button of the adjustment remotecommander.
Exiting the “Forced Camera Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander.4) Select page: 0, address: 01, and set data: 00.
JK-218 board
JK-217 board
VC-281 board
VA-117 board
Adjustment remotecommander (RM-95)
Flexible board(From the Lens block assembly)(27P)
Lens block assembly
AC poweradaptor AC IN
Battery terminal board(6P)
Mechanism deck
FP-440 flexible board(24P)
Extension cable (100P)(J-6082-352-A)
2-17
DCR-TRV24E/TRV25E/TRV27E
2-18.CK-108 BOARD< STEP 1 >
CK-108
2 Two tapping screws (M1.7 × 3.5)
5 Control switch block (SH-CX2670)(18P)
6 Control switch block (KP-CX2670)(8P)
4 Tripod (Large)
3 Bottom frame
1 Three screws (M1.7 × 4), lock ace, p2
CK-108
4 Two tapping screws (M1.7 × 3.5)
7 Tapping screw (M1.7 × 3.5)
5 Speaker retainer assembly
6 Speaker (2.0cm)
3 Speaker (2P)
8 Harness (PV-139)(8P)
2 Harness (PV-139)(20P)
1 P harness retainer
P harness retainer
Attach the 1 P harness retainer so that the harness does not come out as shown.
9 CK-108 board
Caution
< STEP 2 >
2-18
DCR-TRV24E/TRV25E/TRV27E
2-19.HINGE ASSEMBLY(Before starting disassembling, remove the LCD unit referring to section 2-1)
2
1 Four screws (M1.7 × 4), lock ace, p2
1 Two claws
3 Hinge cover (rear)
2 Hinge cover (front)
7 Hinge assembly
5 FP-442 flexible board
4 Screw (M1.7 × 2.5), p
6 Harness (PV-139)(8, 20P)
2-19
DCR-TRV24E/TRV25E/TRV27E
2-20.CONTROL SWITCH BLOCK (PS-CX2670)< STEP 1 >
< STEP 2 >
4 Zoom cover
2 Grip cover
1 Two screws (M1.7 × 2.5), p
3 Two tapping screws (M1.7 × 5)
5 CS frame assembly
1 Tapping screw (M1.7 × 5)
2 Two tapping screws (M1.7 × 3.5)
3 Tapping screw (M1.7 × 5)
4 Tapping screw (M1.7 × 3.5)
2-20
DCR-TRV24E/TRV25E/TRV27E
< STEP 3 >
2-21.MEMORY STICK CONNECTOR
3 Control switch block (PS-CX2670)
1 Tapping screw (M1.7 × 3.5)
2 FP-438 flexible board (8P)
1 Three tapping screws (M1.7 × 5)
5 Screw (M1.7 × 2.5)
4 Eject knob
3 Grip lock assembly7 Memory stick connector
2 Two screws (M1.7 × 2.5), lock ace, p2
6 FP-438 flexible board (10P)
Eject knob
CautionWhen removing the 3 Grip block assembly, be careful that it can be easily caught by the dowel and the protrusion of the Eject knob shown in the illustration. Because the Eject knob is caught by the Grip block assembly, the Eject knob can be easily removed if it is separated from the Grip block assembly.
Dowel
2-21
DCR-TRV24E/TRV25E/TRV27E
MA-409
CK-108
VA-117
VC-281
LB-077
CD-366
JK-217
JK-218
PD161
FB-219
CCD IMAGERSWITCH, CONNECTORMANUAL FOCUS SENSORSTEADY SHOT, A/V IN/OUTDIGITAL IN/OUTEVF, EVF BACK LIGHTMIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCHRGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHTAUDIO/VIDEO SIGNAL PROCESSCAMERA PROCESS, MPEG/DIGITAL STILL PROCESS, VIDEO/AUDIO SIGNAL PROCESS,SERVO, CAMERA/MECHA/HI CONTROL
CD-366CK-108FB-219JK-217JK-218LB-077MA-409PD-161VA-117
VC-281
NAME FUNCTION
2-22.CIRCUIT BOARDS LOCATION
2-22E
DCR-TRV24E/TRV25E/TRV27E
2-23.FLEXIBLE BOARDS LOCATIONThe flexible boards contained in the mechanism deck are not shown.
FP-434
FP-441
FP-444
FP-442
FP-435
FP-445
FP-443
FP-438
FP-436
FP-440
FP-437
CONTROL SWITCH BLOCK(PS-CX2670)
CONTROL SWITCH BLOCK(KP-CX2670)
CONTROL SWITCH BLOCK(SH-CX2670)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
LinkLink
3. BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (4/4)
POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (3/4) POWER BLOCK DIAGRAM (3/3)
OVERALL BLOCK DIAGRAM (2/4) POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (1/4)
OVERALL BLOCK DIAGRAM (4/4)
POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (3/4) POWER BLOCK DIAGRAM (3/3)
OVERALL BLOCK DIAGRAM (2/4) POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (1/4)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/4)
3-1 3-2
SECTION 3BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
X250120MHz
X210124.576MHz
55
IC1502
135
59
63
CH SO,SCK
139
PANEL G
CAM SO,SI,SCK
29
PANEL B
IC2302
162019
TPA+,-TPB+,-
PANEL R
ZOOM MOTORDRIVE
HALL AD
ND HALLAUDIOA/D CONV.
138
106
75
79
DV IN/OUT
73
2
AD0-AD13
68
71
DV SIGNAL
11
37
•
159
IC1501
PROCESS
IRIS DRIVE+,-
9
105
41•
33
78•
79
161
135
Y
1
IRIS HALL +,-
CCD OUT+,-
XSHD,XSHP,CLPDMV1-V4RG,H1,H2
6
170
78
C
L BUS
179
71
24
DV INTERFACE
73
68
31
2
MC BUS
75
FMR A,B
ZMR A,B
IC2102
128
TRCK
77
CN1006
4
TIMINGGENERATOR
3
20
18
CN5353
CN001
FOCUS MOTORDRIVE
136
42
25
45
47
CD-366 BOARD(1/2)
LCK
22
145
EXT STROBO
EXT STROBO
142
26
14
15
8
9
51
141
127
153
IC1301
156
152
L
133
132
R
Y
C
127
IC2101
99
134
61
59
62
97
79
VC-281 BOARD(1/5)
ND HALL
81
EVF G
HALL AD
2
83
12
IC1101
LENS ASSY
(PAGE 3-5)
M
M
IC2501
18
PITCH ADYAW/PITCH
8
H
IRIS(SHUTTER)
SENSOR
YAW AD
AMP
MANUAL
129
YAW SENSOR
PITCH SENSOR
17
5
ND FILTERDRIVE
SE5301
8
SE5302
|
M
8
(1/2)
HD,VD
DATA TO SFD
FOCUSMOTOR
FOCUS
EVF R
DATA FROM SFD
1-4 10-12
SENSOR
FB-219 BOARD
JK-217BOARD(1/3)
EVF B
SFD BCK
4
88
123
120
VSP SO,SI,SCK
20
FRRV,TRRV,TRRT
6
18
FRRV,TRRV,TRRT
PANEL R,G,B
HD,VD
EVF R,G,B
Y
C
DATA TO SFDDATA FROM SFDSFD BCK
CAMERA CONTROL
CN6001 CN5903
CN5902
CN4003
CN1007
CN4002
PH6001,PH6002
21
ATF ERR
ZOOMMOTOR
PB CK
66
56
25
6
AD DT
Y0-Y7
C4-C7
Y0-Y7
A0-A23
D0-D15
HS TXD,RXD,SCK
M
CN1301
C0-C3
HD,VD,OEHD,VD,OE
CCDIMAGER
NIGHT SHOT
IRISMETER
5
19
17
23
205
201
MC BUS
211
210MF A,B
TOOVERALLBLOCK DIAGRAM(3/4)
TOOVERALLBLOCK DIAGRAM(2/4)
213
ZOOM VR AD
6
207
HS TXD,RXD,SCK
IC2301
CN5352
215
130
67
203
211USBI/F
199
3
CN1501CN5101
CN5101
CN1501
19
18
8
9
21
1
1
REC DT
3
41
REC CK
7
TOOVERALLBLOCK DIAGRAM(4/4)
3
11
8
AGCA/D CONV.
IC5101
24 27 12 10
4 1 14 16
65
25
21
5
4
1
2
47
35
37
38
13 14 1
40
44
9
12
13
X150154MHz
29
30
IRISDRIVE
17
7
15
16
13
14
8
9
10
11
23
2
9
10
21
4
11
12
95
97
96
25
74
196
48
CHCK
CAM SO,SI,SCK
A0-A13
Y0-Y7
C0-C7
D0-D15
CHCK
HD,VD,FLD
PBLK
|
44
57
CLPOB
CH SO,SCK
XNS SW
76
IC1601CAMERAPROCESS
102121 154 133
IC170164MbitSDRAM
20 35 2 13 42 53•
A0-A13 D0-D15
4
|
7
Y0-Y7
VCK
Y0-Y7
DSCK
C0-C3
Y0-Y7
C0-C3C0-C7
HD,VD,OE HD,VD,OE HD,VD,OE
HD,VD
COL0-3
ADAI2
ADAO2
SFD BCK
Y0-Y7
VSP SO,SI,SCK
C4-C7
•
11 S/H
IC5102
(1/16)
(1/16)
(3/16) (4/16)
(4/16)(14/16)
(12/16)
(2/16)
(2/16)
(2/16)
(11/16)
(7/16)
(8/16)
MA-409BOARD(1/3)
VA-117BOARD(1/4)
12
16
ND HALL +,-
FC PWMFC EN SPCK
(IC1704)
ZM PWMZM EN
IP PWMIP EN
ND PWMND EN
ND DRIVE+,-
FOCUS +,-
ZOOM +,-
NDFILTERMATER
H
MR
MR
36
37
44
45
IC1302
FORCUS/ZOOM/IRIS/
ND FILTERCONTROL
14
1518
26
27
12
13
61
60
53
52
6
3
5
IC1801EVR6
7
17 16 22
12 11 6
14 15 22
30
31
15
16
13
64
61
60
8
9
10
47
48
1
12
3
1
175
169
9 2 34 27 22 11•
44
177
IC1704
A16-A23 D0-D7
153
|
170
48
47
117
118
119
65
|
72
76
|
83
91
|
97
99
|
115
34
2
6
IC2001
VIDEOA/D CONV.
38
37
36
42
|
49
52
|
59
84
85
86
144
137
133
128
139
7
6
140
43
|
46
27
28
42
HD,VD,OE
HD,VD,OE
58
47
54
57
190
195
194
191
65 82 63
8
18
24
206
202
212
214
208
216
204
200
22
2 49
13 15
611
183
184
88
87
62
|
93
60
|
39
221
223
IC2905DIGITALSTILL
CONTROL
187
184 4
|
215
213
|
IC3002
(6/16) (6/16)
(5/16)
(5/16)
(10/16)
(10/16)
259
48161
45
36
38
29
16MbitSDRAM
IC3003
32
24
27
19
49
12
39
2
CN1006CN5305
5
4
15
14
XTALOSC
X290148MHz
IC2904
AFCK
DSCK(IC1704)
XTAL 48M LK
XTAL 48M LK(IC2904)
USB D+,D-
USB D+,D-
SPCK(IC1704)
ASDATA
MCLK
238•
239
JK-218BOARD(1/3)
JK-218BOARD(2/3)
CONTROLSWITCHBLOCK(1/2)(PS-CX2670)
4
5
2
1
4
5
2
1
9
11
13
2
4
6
MS BS,DIO,SCLK MEMORYSTICK
(USB)
CN5351CN5353CN1006
CN1008
8
9
7
8USB D+,D-
4 6
92 94
92 94
4 6
4
6
MPEGMOVIE
PROCESS
CHARACTERGENERATOR
AUDIO
DIGITALSTILL
PROCESS
SPCK(IC1704)
44 45
Y0-
Y7
C0-
C7
SPCK(IC1704)
AFCK(IC2001)
AFCK(IC2001)
SPCK
Y
C
MF A,B
(1/2)FLASH
MEMORY
(PAGE 3-7)
(PAGE 3-3)
DV OUT
1
2
3
(TRV25E/TRV27E MODEL)
: TRV25E/TRV27E
: TRV24E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-3 3-4
3-2. OVERALL BLOCK DIAGRAM (2/4)
PD-161 BOARD(1/3)
VC-281 BOARD(2/5) CK-108BOARD
(1/3)
RGBDRIVE
VCOM
VR,VG,VB
COM
DAC VGLAC
CN5502FORADJUSTMENTS
LCD UNIT
2.5 INCH: TRV24E/TRV25E
3.5 INCH: TRV27E
LCD901
CN5501
CN5203CN5202CN1005 CN5652
PANEL 2.8V
Q5601
(1/2)
(1/2)
(2/2)
(PAGE 3-7)
IC5501484746
27
CURRENT
INVERTER
BACKLIGHT
T5601Q5604/Q5605ND901
BACKLIGHT
D901(STARTER)
BL HIGH
BL LOW
DETIN
CN5601
DRIVE
DET
IC56023 4
35
202224
4039
TIMINGGENERATOR
SP901SPEAKER
HD OUT
(2/2)
IC5502
IC5601
1
1
484
5 2
6
7
464542
2 58
12
24
11
192021
45
1012
18
BL REG10
3
CN5651CN5204
CN5205
CN6101
SP+,-
21
Q5603
LED DRIVE
10
1532
98
1413
12 4
4
10
1532
98
13
4
12 4
21
13
222119
1517
2324
2527
VGPANEL COM
XHD OUT
PANEL R,G B
HDVD
14
7
21
VD,SO,SCK
BL CONT
SP+,-
28
192022
2624
17
1614
18
20
18
2422
1416
20
18
2422
1416
3
1
7111054
PANEL VGCN1002FORADJUSTMENTS
PANEL R,G,B
DATA TO SFD
VD SO, SCK
VSP SO, SCK
DATA FROM SFDSFD BCK
HD,VD
PANEL COM
TOOVER ALLBLOCK DIAGRAM (4/4)(VA-117)
TOOVER ALLBLOCK DIAGRAM (1/4)
TOOVER ALLBLOCK DIAGRAM (3/4)
XHDEVF VCOEVF VG
IC4202TIMING
GENERATOR
LCDUNIT14
1315
1612
3
LB-077 BOARDVA-117 BOARD(2/4)
MA-409 BOARD
(2/3)
107
11
9
18
8
4 BACK LIGHT DRIVE
D6102BACKLIGHT
R,G,B
COM
Q6102
IC6101
CN6102
LCD903
17
CN4201
CN1007 CN4002
1114
1312
3
10
IC4201RGB
DRIVE
EVF R,G,B
VD SO,SCK
HD
VCO
G
VD
(1/6)
(1/6)
(2/6)
(6/6)
202224
464542
484746
14
1 8
148
4039
97
24
12
YC
GG
27
26
3028
6264
467
3634
5658
3532
19
181422
394842
18
1715
YCV
L
16C
ACC
J5302(1/2)
AGC
VIDEO IN/OUT
V
JK-217 BOARD(2/3)
VC-281 BOARD(3/5)
R
R
R
14
LR
LR
12
V
L
L
10
J5302(2/2)
R
63
51
49
6460
L
RL
8
6463
49
60
51
R
CN5305
SHOE MIC L FP-436 (FLEXIBLE)
CN4003
CN5902CN5901
CN1006
INTELLIGENTACCESSORYSHOE (1/2)
CN1007
VSP SO,SCK
CN4004
CN4002
CN4001
L
Y
IC4301AUDIO
I/O
IC4101
YC
YC 26
24
22
20
18
2 3
9 10
757377
6870
74
76
71
72
54
53
45
43
59
56
58
57
50
46
48
44
757377
6870
74
76
71
72
54
53
45
43
59
56
58
57
50
46
48
44
DATA FROM SFDIC2201
D/A CONV.A/D CONV.
RL
R
R
L
L
RL
DATA TO SFDSFD BCK
HP RHP L
HP RHP L
(12/16)
1516
32
98
12
(3/6)
MIC AMP
IC4401
1
333
35
2214
EVF R,G,B
Y
L
R
Y
C
C
3648
MIC901 MIC L
MIC R
J5901MIC
(PLUG IN POWER)
J5902
(HEADPHONES)
15 3
(PAGE 3-2)
(PAGE 3-5)
2
3
4
5
S VIDEO
AUDIO/VIDEO
OUT : TRV24EIN/OUT : TRV25E/TRV27E
OUT : TRV24EIN/OUT : TRV25E/TRV27E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-3. OVERALL BLOCK DIAGRAM (3/4)
3-5 3-6
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
X250120MHz
16
MODE SW A - MODE SW C
CONTROL
SREEL FG
CAP ON,CAP FWD
DRUM PWM
FRRVTRRTTRRV
TAPE LED ON
13
CAP PWM
|
LOAD,UNLOAD
DRUM PG
15
DEW AD66
63
65
36
38
1
80
77
75
67
64
33
32
72
69
63
68
65
74
78
76
82
80
83
69
67
70
84
179
178
52
32
33
45
CAP FG
TAPE END
TAPE TOP
106
DRUM FG
TREEL FG
MECHA
108
|
EEPROM
2-4
VSP SO,SI,SCK
VD SO,SI,SCK
VSP SO,SI,SCKVSP SO,SCK
FRRV TRRT,TRRV
MC BUS
HI SO,SI,SCK
REC PROOF
CHIME SDA,CHIME SCK,CHIME VDD
XCC DOWN
(2/2)
LPF
CAP ERROR
DRUM ERROR
11
15
IC4501(1/2)
PWM
64
58
SWITCHING
SWITCHING
Q4509
Q4510
20
SENSOR
MOTOR
J MECHA DECK
DRUM FG AMP
S902
1
|
LOADINGDRIVE MOTOR
H902
H901
C INS903
CN1010
D901
5
11
CONNECTOR
TAPE TOP SENSOR
Q902
DRUM FG
CAPSTAN
MODE
24
SENSOR
15
S REEL
SWITCH
XCC DOWN
S REEL +, –
T REEL +, –
LM +, –
18
MOTOR
CN1009
21
TAPE END DETECT
4PIN
T REEL
|
TAPE TOP DETECT
7
LOADING MOTOR
TAPE LED
CC DOWN
M
REEL FG AMP
M903
REC PROOF
9
16
SENSOR
DRUM
EVEN
ODD
TAPE END SENSOR
|
20
10
5
CAPSTAN
DRUM PG
23
|
2
M
12
DRUM PG AMP
27
CAP VS
DEW
17
4
25
DRUM VS
FG
M902
1
DRUM
S901
Q901
CN901
|
M901
25
22
TOOVERALLBLOCK DIAGRAM(4/4)
TOOVERALLBLOCK DIAGRAM(2/4)
SWP
17 20
SWP
CN1002FOR ADJUSTMENTS
AD DT
6
PB Y OUT
1
EQ
20
PB CK
6
REC/PB 7
2
SWP
15
6
CN1901
EVEN 3
ODD
2
5
22 24
VSP SO, SCK
REC CK
REC DT
PB CKTOOVERALLBLOCK DIAGRAM(1/4)
VC-281 BOARD(4/5)
166
165FG AMP
(14/16)
(14/16)(13/16)
(9/16)
(9/16)
(13/16)
(4/6)
(4-37)
111
164
190
89
88
197
198
192
193
196
195
119
180
1
3
ATF ERR
13
34 31
4
53 52
4950
29
25
21
19
20
18
35
42
IC1901
IC190240
42
27
REC CK
REC DT
RF MON
AD DT
6
IC2401
MOTORDRIVE
MOTORDRIVE
CAPSTAN
DRIVE
IC2401(RABI)
LPF
4
|
1
11
14
|
M
CN1011
IC2502
IC2501
A/D CONV.PLL
AMP
CAPSTAN
DRUM
41
44
43 20
18
20
1845
19,21
15,17
19,21
15,17
CN4002 CN4002 CN1007CN1007
26 @27
7 @8
22 @23DEW AD
DRUM U,V,W
CAP U,V,W
FG 1,2
SPCK (IC1704)
(1/2)
(2/2)
VA-117 BOARD (3/4)
(PAGE 3-2)
(PAGE 3-8)
(PAGE 3-3)
2
4
6
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-4. OVERALL BLOCK DIAGRAM (4/4)
3-7 3-8
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
S
BT901
Q4602
10MHzX3101
32.768KHzX3102
S5203
BT5201
Q4610
6
5
1
BATTERYTERMINAL
DC IN 3
2
4
IC4501
IC4505DC/DC
CONVERTER
D 1.9V
PLL1.5V
D 1.5V
1.5V(IC1601)
PANEL -15.3V
A 2.8V
AU 2.8V
MT 5V
CAM -6.5V
CAM 12V
IC2703
IC2905
LANC I/O
1110
12
I/F43
42
74
VDD SWITCH
IC27027
4
3
5
6
RESET
79
3
59
41
45
14
53
62
73
66
XPHOTO STBY SW
XS/S SW
XCAM MODE SW
DIAL A
VCC
XRESET
IB SI
IB SO
BATT/EXT
IC3101HI CONTROL
HI CONTROL
67
29
28
51
52
5
35
37
SIRCS PWM
XCC DOWN
XCC DOWN
37
168
30
REC PROOFREC PROOF
CHIME SDA
CHIME SCK
CHIME AD0
CHIME SDACHIME SCKCHIME VDD
CHIME AD
XEJECT SW
XEJECT SW
RXD
KEY AD5
KEY AD0
KEY AD5
SIRCS SIGIR ON
VTR DD ON
SHOE ON
CONTROL SWITCHBLOCK(KP-CX2670)
S103,S102 EXEC
CN5202 CN1005
CN1008
CN5203
CN5652
CN5653
CN5903
CN5207
CN5201
1
15
CK-108BOARD(2/3)
PD-161BOARD(2/3)
MA-409BOARD(3/3)
VA-117BOARD(4/4)
(2/2)
(2/2)
MEMORY FUNCTION SW,MENU SW,VOLUME SW,DISPLAY SW
VTR FUNCTION SW
S5201-5206
S101-116
CN4003 CN4002 CN1007
Q4001,4003
CN5902
CN4001
RESET
S100,101
LITHIUMBATTERY
CONTROL SWITCHBLOCK(PS-CX2670)
68 KEY AD6
PANEL REVERSE SW
S001
LED DRIVE
CN4601
D 2.8V
EP 2.8V
EP 13.3V
RP 4.75V
A 4.75V
AU 4.75V
VC-281 BOARD(5/5)
606165 KEY AD3
KEY AD4
KEY AD1KEY AD2 A
80 DIAL B
57 SHOE ID1
SHOE ON
58 SHOE ID2
XVTR MODE SW
2
1
7
KEY ADD
6 XPHOTO FREEZE SW
20
4
21
25
24
23TXD
TXD,RDX,SCK
SCK
RXD
185
191
190 TXD
CAM DD ON
IR ON
SCK
39
40
LANC IN
LANC OUT
17
FAST CHARGE
VTR UNREG
CN1007CN4002
CN4004
Q3101
BATT LI 3V
CK-108BOARD(3/3)CN5202
10
9
31
32
17
18
17
18
28
10
20
1
LCDDRIVE
IC5651
7
811
30
CN5654
CN5203CN1005 CN5652
PD-161 BOARD (3/3)
12
1
2
12
1
2
CD-366BOARD(2/2)
(LANC)
S5351
J5301
LANC SIG
LANC SIG
ZOOM VR AD
EXT STROBO
HS TXD,RXD,SCK
HI EVER SO
HI EVER SCK
XOSD SCK
16
BATT SIG
BATT SIG
BATT/EXT
FAST CHARGE
BATT UNREG
VTR UNREG
VTR DD ON
CAM DD ON
BL REG
BL CONT BL CONT
CONTROLSWITCHBLOCK(SH-CX2670)
(4/6)
(15/16)
(15/16)
(15/16)
(5/16)
(5/16)
(2/2)
1
3
4
65
65
PRT HEAD UNREG
SHOE UNREG
LANC SIG
EXT STROBO
SHOE ID1,2
HS TXD,RXD,SCK
14
15
11
9
12
10
7
8
13
4
12
7
9
6
8
11
10
5
93
90
91
89
79
80
82
86
85
84
87
93
90
91
89
79
80
82
86
85
84
87
INTELLIGENTACCESSORYSHOE
FP-309(FLEXIBLE)
S301,302
FP-444(FLEXIBLE)
JK-218 BOARD (3/3)
JK-217 BOARD (3/3)
EJECT SW
CN5353
CN5305
CN1006
CN1501
CN5101 CN5102 S201
EDIT SEARCHSW
S202,203
FP-443(FLEXIBLE)
TOOVERBLOCK DIAGRAM(3/4)
END SEARCH SW,AUDIO DUB SW,INDEX SW
3635
38
37
39
40
34
33
56
3
4
2
1
7
8
42
16
18
19
5
1
1
3
4
6
9
1
8
7
5
DIAL A,B
. .
.
.
.
160
.
162
.
221
HI SO
HI SO,SI,SCK
HI EVER SO,SCK
HI SI
XHI SCK
200
201.
.
199
EEP TXD
EEP RXD
EEP SCK
207
206
205
222223
.
.
.
3
D5901,5902
IC5901REMOTE
COMMANDER
(NS LED)
RECEIVER
.
.
.
.
.
.
5
1
2
3
8
6
25
23
5
1
2
3
8
6
25
23
(2/2)
TOOVERALLBLOCK DIAGRAM(2/4)
TOOVERALLBLOCK DIAGRAM(1/4)
(2/2)
EEPROM
IC2901.
. 8,11
2
9,12
21
23
5
3
1
6
11
18
COM1-4SEG1-16 LCD
INDICATOR
LCD902
(PAGE 3-4)
(PAGE 3-1)
(PAGE 3-5)
5
1
6SEL/PUSH
EXEC
BACK LIGHT SWEXPOSURE SW
POWER SW
START/STOP SW
S1
S2
PHOTO SW
S071PHOTO REC
KEY AD0
ZOOM VR
RV001
FADERFOCUS/INFINITY
SUPER NS/COLOR SLOWS
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-9 3-10
3-5. POWER BLOCK DIAGRAM (1/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
L4503
L4506
L4502 L4513
L4515
L4514
L4501
L4508
L4507
L4510
L4504
L4505
F4602
F4603
F4604
F4601
F4605
L4509
L4516
Q4508
Q4505
Q4506
Q4510
Q4503
Q4509
L4511
L4522
L4520
BATT/XEXT
F4606
L4519
30
28 2VCC
40
42
50
45
6
29
IC4501DC/DC CONVERTER
27
49
1
5
21
22
4
1
5
6
2
3
34
37
46
11
64
58
15
OUTPUTVCC-1,2,3
OUTPUTVCC-4,5,6
OUTPUTVCC-7
VREF
RT
CT
STANDBY-3
STANDBY
NONINV INPUT-5
NONINV INPUT-6
OUTPUT-1
MOS GATE-1
OUTPUT-7
OUTPUT-3
OUTPUT-2
OUTPUT-6
OUTPUT-5
OUTPUTMONITOR-1
OUTPUTMONITOR-7
7MONITORINPUT-7
31STANDBY-7
OUTPUTMONITOR-3
OUTPUTMONITOR-2
SWITCHING
SWITCHINGQ4512
Q4511SWITCHING
SWITCHINGQ4501 T4501
D 1.5V
PLL 1.5V
BL REG
BL CONT
1.5V(IC1601)
A 2.8V
AU 2.8V
D 2.8V
A 4.75V
RP 4.75V
A 4.75V
AU 4.75V
CAP VS
DRUM VS
CAP ERROR
6
1
5
4
3
2
Q4601,4602
Q4605-4610
SHOE ON
SHOE UNREG
PRT HEAD UNREG
CHARGESWITCH
BATT UNREG
ACV UNREG
Q4603, 4604
OUTPUTMONITOR-4
OUTPUT-4 57
MOS GATE-4
18
54
8
S BATT SIG
VTR DD ON
5V REG
EMERGENCYDETECT
Q4513
-7.5V REG
Q4517,4518
13.3V REG
Q4521
DC IN
IC4505
Q4502,4504,4507
VIDEOIN/OUT
VA-117 BOARD
LF4601
CN4601
BT901
BATTERYTERMINAL
DRUM ERROR
COMP 41
VREF
SWITCHING
SWITCHING
SWITCHING
SWITCHING
SWITCHING
BAT
T FE
T O
N
INIT
CH
AR
GE
ON
D4503RECT
A 4.75V
EP 2.8V
1.5V (IC1601)
A 2.8V
D 1.9V
RP 4.75V
BATT SIG
BATT UNREG
TOPOWERBLOCKDIAGRAM(2/3)(VC-281)
EP 13.3V
CAM -6.5V
EP 4.75V
PANEL -15.3V
D 2.8V
1.9V REG
RECT -15.3V REG
D4502
EP 13.3V
INIT CHARGE ON
SHOE ON5
BATT/XEXT
VTR DD ON
CAM DD ON
FAST CHARGE
BATT UNREG
MT 5V
VTR UNREG
EP 13.3V
D 2.8V
PLL 1.5V
CAP VS
CAP ERROR
DRUM VS
DRUM ERROR
CAM 12V
LCDUNIT
IC6101BACKLIGHTDRIVE
20
IC4201 IC4202TIMING
GENERATORRGB
DRIVE
IC5901REMOTE
COMMANDERRECEIVER
CN4201
LED ON/OFF
CN6101CN6102
LCD903
EP 13.3V
MT 5V
R4011,4012
D5901, 5902
D6001
PH6001, 6002
A 4.75V
AU 4.8V
EP 2.8V
EP 4.75V
16
Q4519,4520
D 1.5V
D 1.9V
LB-077 BOARD
MA-409 BOARD
FB-219BOARD
15VREG
CAM DD ON
CAM 12V
Q4514-4516
CAM -6.5V
7
81
1
4
1
20
17
8
FB4202
CN4004
BL REG
BL CONT
PANEL -15.3V
PANEL 13.3V
PANEL 4.75V
PANEL 2.8V
EP 13.3V
EP 4.75V
EP 2.8V
7
6
5
4
3
TOPOWERBLOCK DIAGRAM(3/3)(CK-108)(PAGE 3-13)
CN4001
3
1
4
215
14
FP-436(FLEXIBLE)
INTELLIGENTACCESSORY
SHOE
IC4301AUDIOIN/OUT
IC4401MICAMP
IC4101
34
35
18
20
15
17
19
21
31
33
8
9
7
9
27
29
11
13
14
16
26
28
30
32
10
12
36
6
8
2
3
23
25
4
1A 4.75V
D 2.8V
MT 5V
MT 5V
CN4002
AU 2.8V
AU 4.75V
REG
Q4301
SP VCC
C/D VS 1.5V
BL REG UNREG
VTR UNREG
NIGHTSHOTLED
CN5902 CN4003CN5903
CN6001
11
5
9
11
5
9
TALLYLED
MANUAFOCUS
SENSOR
2
6
5
1
1
2
(PAGE 3-11)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-11 3-12
3-6. POWER BLOCK DIAGRAM (2/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
D2071
S5203
BT5201
FB2502
FB1702
FB2101FB2903
FB3001
L1902
FB1901
FB1301
Q2706
Q2401
R2431
2
IB SI
BATTER INDETECT
1
XLANC PWR ON
RESET
43
BATT INREG
VCC
Q2701
8
XRESET
17
BTT LI 3V
BATT/XEXT
ACV SENSI/F
FAST CHARGE
Q3101
VTR UNREG
DV
IC2702
VTR DD ON
D 2.8V
LANC I/O
INIT CHARGE ON
VIDEO
VTR DD SENS
31
HI CONTROL
A/D CONV.
56
XREELHALL ON
IC3101
73
153
IC2703
37
AUDIOAUDIO
55
A/D CONV.
VCC
A 2.8V
L2201
74
BATT SIG
CAM DD ON
54
LANC DC
42
POWER
ADC&DAC
8
UNREG
XPHOTO STBY SW
BATT SENS
4
38
XCAM MODE SW
14
7
SHOE ON
XVTR MODE SW
1
DV
IB SO
1.5V(IC1601)
MT 5V
RP 4.75V
A 4.75V
CN1007
PLL 1.5V
D 1.9V
D 2.8V
A 2.8V
IC1002 IC2301
IC1501D 1.5V
D 2.8V
USB 3.1V
TOPOWER BLOCKDIAGRAM(1/3)(VA-117)
VC-281 BOARD
RESET
LITHIUM BATTERY
EVER 3.0V
TOPOWERBLOCK DIAGRAM(3/3)(PD-161)
S REEL,
13
19
4PIN18
J MECHA DECK
SENSOR VCC
CHIME VDD
CN901
H901, 902
D901
FOCUS
SENSOR
ZOOM
SENSOR
SHOE ON
BATT SIG
INIT CHARGE ON
VTR DD ON
CAM DD ON
FAST CHARGE
BATT/XEXT
BATT UNREG
MT 5V
VTR UNREG
1.5V(IC1601)1.5V(IC1601)
D 1.9V
A 2.8V
D 2.8V
D 1.5V
PLL 1.5V
A 4.75V
RP 4.75V
CAP VS
CAP ERROR
DRUM VS
DRUM ERROR
CAM 12V
CAM -6.5V
3
7
5
4
8
6
IC1902 IC1901
S/H,AGCA/D CONV.
IC15022.8VREG
IC1303
IC2001 IC2101 IC2102 IC1601
IC2201 IC2302
LANC DC
20
6
10
14
CN001
CN1008
Q1001,1002
CAMERAPROCESS
CAMERA
IC2501CONTROL
INTERFACESIGNALPROCESS
D 2.8V
EEPROM
IC2502
28
40
39
13
1
2
CN1005
CN5202
D1.5V
PLL 1.5V
D2.8V
CN5203
30
CN1006 CN5305
12
20
2
USBI/F
3.1VREG
IC1704
TIMINGGENERATOR
IC5102S/HREC/PB
AMPEQ,
A/D CONV.PLL
A 2.8V
D 1.9V
2.8V
IC170164MSDRAM
RP 4.75V
MT 5V
EP 13.3VEP 13.3V
RV001
D001 (TALLY)
ZOOM VR
LED
D 2.8V
MS VCCUSB 3.1V
MS VCC ON
D2.8V
EVER 3.0V
LANC DC
SE 2.8VSE 2.8V
CK-108 BOARD(1/2)
JK-217 BOARDSENSORYAW, PITCH
SENSOR AMPPITCH/YAW
SE5301, 5302
(LANC)
J5301
CONNECTOR
T REELSENSOR
TAPE LED
DRUM FG,PG AMPMOTOR DRIVE
IC2401
43
6
REEL FG AMP
LOADING
DRUM,CAP ERROR AMPTAPE TOP,END DET
DRUMCAPSTAN FG AMP
CAPSTAN MOTOR DRIVE
MOTOR DRIVE
DRUM ERROR
CAP VS
EV 13.3V
CAP ERROR
DRUM VS
CN1010
TAPE LED A
D 2.8V
MT 5V
A 4.75V
A 2.8V
3.1V
CAM DD ON
VTR UNREG
CH
IME
PW
R C
ON
T
XR
EEL
HA
LL O
N
LENS ASSY
IC5101 CCD
IMAGER
Z MR VCC
F MR VCC2.8V7
21
CN1301
CN5101CAM 15V
CAM 7.5V
A 2.8V
CN1501
CAM 12V
CAM -6.5V
DIGITAL
HICONTROL
CAM DD ON
MS VCC ON
CHIME PWR CONT
IC2905
CONTROL SWITCHBLOCK(PS-CX2670)
S1
5
2
4 POWER
IC1101
AMP
IC1504 IC1503
L1101
CD-366 BOARD
EEPROM
IC2901
OSCXTAL
IC2904BUFFER
IC2903
SDRAM
16M
IC3003
3
7MEMORY
STICK
16
35
STILLCONTROL31
23
168
IC1301
IRIS
FOCUS/ZOOM/
NDDRIVE
IC1302FOCUS/
ZOOM/
IRIS/
ND
CONTROL
IC1801EVR
MEMORY
16M
FLASH
IC3002
145362
7577
6467
24 2
MR
MR
18
22
8
4
2 5
3.1VREG
3
5
32
MPEG MOVIEDIGITAL STILLPROCESS
5
1
4
3
23
25
2
8
35
34
26
28
30
14
16
11
13
27
29
31
33
19
21
15
17
7
9
6
36
12
10
32
18
20
R1022
45
FB1505
3
(PAGE 3-10)
(PAGE 3-13)
2
3
VCR
PLAYER
OFF(CHG)
MEMORY
CAMERA
(TRV25E/TRV27E MODEL)
: TRV25E/TRV27E
: TRV24E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-13 3-14E
3-7. POWER BLOCK DIAGRAM (3/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN5651
CN5652
CN5501EP 4.75V
EP -15.3V7
4
3
5EP 13.3V
6EP 2.8V
8
7
4
3
5
6
8
PANEL 4.75V
BL CONT
PANEL -15.3V4
7
BL REG89
6PANEL 13.3V
5PANEL 2.8V
3
24
3
1
23
PD-161 BOARD
CK-108BOARD
TOPOWERBLOCK DIAGRAM(1/3)(VA-117)
TOPOWERBLOCK DIAGRAM(2/3)(CK-108)
FB5503CN5202 CN5204
FB5502
FB5501
IC5601,5602INVERTER
BACK LIGHTDRIVE
IC5501
RGBDRIVE
IC5651INDICATOR
LCDDRIVE
IC5502
TIMINGGENERATOR 28
LCDUNIT
LCD901
2.5INCH: TRV253.5INCH: TRV27
ND901BACKLIGHT
10
16
Q5502-5505
CN5601
BL HIGH
EVER 3.0V
(PAGE 3-9)
(PAGE 3-12)
1
3
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-1 4-2
4-1. FRAME SCHEMATIC DIAGRAM (1/3)
FRAME SCHEMATIC DIAGRAM (1/3)
SECTION 4PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
20PCN5305
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
10P
CN
1011
12345678910
27P
CN
1010
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
10P
CN
1901
12345678910
20PCN1002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
27P
CN
1009
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
6PCN5102
1
2
3
4
5
6
12PCN5353
1
2
3
4
5
6
7
8
9
10
11
12
30PCN1006
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
A
27PCN5101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
2724PCN1501
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
27PCN1301
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
REG_GND
LM_U
NLO
AD
TREE
L+PS_V
HE_
GN
D
H_START
XM
OD
E_S
W_B
CA
P_V
XLANK_JACK_IN
XC
CD
OW
N_S
W
FP-4
40
GN
D
FG1
VIDEO_I/O
CA
P_W
HA
LL_G
ND
LANC_SIG
UH
E+
CA
P_U
YS_V
CD-366BOARD
XM
OD
E_S
W_A
REG_GND
CA
P_U
RF_MON
YS_LI
CA
P_V
YEV
EN
SE_2.8V
CH
IME_
SD
A
CA
P_U
LANC_SIG
CA
P_V
PANEL_VG
XO
DD
REG_GND
PS_LI
XR
EC_P
RO
OF
CA
P_U
JIG_TDO
MD(J MECHANISM)
FP-4
43
REG_GND
GND
CA
P_W
FG_V
CC
SWP
XS
DL
EDIT
- S
W
AU_LINE_I/O_R
GNDC
AP
_W
FG_G
ND
XHD/PSIG
YS
DL
EDIT
+/
FG_G
ND
JIG_TDI
HE_
VC
C
GN
D
TMS(MAKER_CHECK)
UH
E-
EJEC
T/
DR
UM
_UFG2
GN
D
GND
CA
P_W
SW
YO
DD
PANEL_COM
Shot
DR
UM
_W
WH
E-
MIC
/REC
_SW
_GN
D
EVF_BL+
Night
TAP
E_LE
D_K
XEJECT_SW
EVF_VG
FG
VH
E+
SW
_CO
M/S
W_G
ND
RF_IN/LANC_JACK_IN
N.C
.
PG
N.C. SR
EEL+
TCK
S_Y_I/O
Super
DR
UM
_W
TAP
E_TO
P
SR
EEL-
EVF_BL-
LANC_DC
DR
UM
_V
LM_L
OA
D
EVF_VCO
CH
IME_
SC
K
KEY_AD0
M_C
OM
TOP
/EN
D_G
ND
S_C_I/O
TAP
E_LE
D_A
FP-4
45
DR
UM
_V
LM_L
OA
D
PD_VCO
HA
LL_V
CC
JIG PIN CPC
TAP
E_EN
D
XM
OD
E_S
W_C
VH
E-
DR
UM
_U
REG_GND
WH
E+
FG/P
G_C
OM
AU_LINE_I/O_L
CH
IME_
VD
D
CA
P_V
DEW
+
JK-217BOARD
XEV
EN
LM_U
NLO
AD
AV_JACK_IN
DEW
-
XS_JACK_IN
FG_V
CC
TREE
L-
GN
D
TPB
USB_D-
REG_GND
USB_DET
REG_GND
REG_GND
KEY_AD5
TPA
REG_GND
NTPB
USB_D+
NTPA
JK-218BOARD
AU_LINE_I/O_L
USB_GND->REG_GND
TPA
S_C_I/O
XS_JACK_IN
SE_2.8V
LANC_SIG
REG_GND
USB_D+
NTPA
REG_GND
VIDEO_I/O
REG_GND
PS_LI
YS_V
S_Y_I/O
XLANK_JACK_IN
NTPB
YS_LI
AV_JACK_IN
TPB
REG_GND
PS_V
AU_LINE_I/O_R
KEY_AD5
USB_VCC->USB_DET
LANC_DC
REG_GND
USB_D-
REG_GND
VC-281 BOARD(1/3)
LENZBLOCK
H
2 3 12
J
179
G
11
E
C
10
K
14136
B
7
I
D
F
155
L
84 16
16
N.C.
N.C.
N.C.
CCD_OUT-
VSUB
XSHP
A_2.8V
CAM_15V
GND
XEJECT_SW
CAM_-7.5V
KEY_AD0
GND
GND
V2
V4
H1
XSHD
GND
RG
H2
RCSUB
V1
CLPDM
GND
CCD_OUT+
GND
GND
V3
N.C.
GND
XSHD
VSUB
GND
KEY_AD0
XEJECT_SW
V4
CCD_OUT-
XSHP
RCSUB
CAM_-7.5V
H2
V3
CAM_15V
A_2.8V
GND
RG
V2
GND
GND
CLPDM
H1
V1
CCD_OUT+
Z_MR_B_P
F_MR_VCC
FOCUS+_P
FOCUS-_P
ND_BIAS-_P
I_BIAS-_P
ND_DRIVE-_P
ND_HALL+_P
F_MR_A_P
I_HALL-_P
Z_MR_GND
ZOOM+_P
Z_MR_A_P
NT_SHOT_P
I_DRIVE+_P
TEMP_P
ND_BIAS+_P
I_DRIVE-_P
ND_DRIVE+_P
F_MR/TEMP_GND
F_MR_B_P
Z_MR_VCC
ND_HALL-_P
I_BIAS+_P
NS_GND
I_HALL+_P
ZOOM-_P
FLEX
IBLE
FLEX
IBLE
TO VIDEO HEADTO DRUM MOTORTO LOADING MOTOR,MODE SWITCH,T/S REEL SENSORTO CAPSTAN MOTOR
FLEX
IBLE
(FOR CHECK)
DV_JACK
USB_JACK
AV_JACK
S VIDEOTERMINAL
LANC_JACKJ5301
J5302
CN5351
CN5352
S5351
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-3 4-4
FRAME SCHEMATIC DIAGRAM (2/3)
FRAME SCHEMATIC DIAGRAM (2/3)
20P
CN
4001
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
24P
CN
4003
123456789101112131415161718192021222324
20P
CN
4201
1234567891011121314151617181920
6PC
N46
01
123456
16P
CN
6102
1V
DD
2V
SS
3V
ST
4V
CK
5S
TB
6EN
7D
WN
8R
GT
9H
ST
10H
CK
2
11H
CK
1
12B
LK
13V
B
14V
R
15V
G
16C
OM
20P
CN
6101
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
24P
CN
5902
123456789101112131415161718192021222324
8PCN5903
1
2
3
4
5
6
7
8
CN5901 4P
1
2
3
4
6PCN6001
1
2
3
4
5
6
100P
CN
1007
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
100P
CN
4002
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
1
A
SH
OE_
MT_
GN
D
SH
OE_
UN
REG
SH
OE_
UN
REG
_GN
D
SH
OE_
ID2
SH
OE_
UN
REG
_GN
D
SH
OE_
ID1
SH
OE_
CO
NT_
AD
PR
T_H
EAD
_UN
REG
SH
OE_
UN
REG
TXD
LAN
C_S
IG
RX
D
SH
OE_
MT_
GN
D
SC
K
SH
OE_
MIC
_L
SH
OE_
MIC
_GN
D
HD
S
STB
Y_O
N
PR
T_H
EAD
_UN
REG
SH
OE_
UN
REG
_GN
D
REG
_GN
D
MF_
A
MIC
_GN
D
EXT_
MIC
_L
HP
_R_O
UT
A_4
.6V
MF_
B
MIC
_GN
D
XF_
TALL
Y_L
ED
KEY
_AD
6
INT_
MIC
_L
MIC
_GN
D
AU
_2.8
V
REG
_GN
D
HP
_L_O
UT
HP
_JA
CK
_IN
REG
_GN
D
NS
_LED
_K
N.C
. (M
F_LE
D)
EXT_
MIC
_R
MIC
_GN
D
INT_
MIC
_R
SIR
CS
_SIG
NS
_LED
_A
EVF_
4.75
V
VS
T
VR
VC
K
LED
_ON
/OFF
EVF_
GN
D
XTA
LLY
_LED
BLK
EVF_
GN
D
VG
STB
ENEVF_
GN
D
HC
K1
LED
_DA
HC
K2
EVF_
VD
D
HS
T
CO
M
VB
BAT
T_U
NR
EG
BAT
T/X
EXT
BAT
T_S
IG
BAT
T_G
ND
AC
V_U
NR
EG
AC
V_G
ND
ENVR
VS
T
HS
T
LED
_DA
EVF_
GN
D VB
HC
K2
EVF_
GN
D
HC
K1
STB
XTA
LLY
_LED BLK
EVF_
VC
C
LED
_ON
/OFF
VC
K
EVF_
4.75
V
CO
M VG
EVF_
GN
DHP
_L_O
UT
MIC
_GN
D
SIR
CS
_SIG
MF_
A
MIC
_GN
D
HP
_R_O
UT
MIC
_GN
D
REG
_GN
D
INT_
MIC
_L
NS
_LED
_K
REG
_GN
D
KEY
_AD
6
INT_
MIC
_R
NS
_LED
_A
A_4
.6V
MIC
_GN
D
EXT_
MIC
_R
HP
_JA
CK
_IN
REG
_GN
D
XF_
TALL
Y_L
ED
AU
_2.8
V
MF_
B
EXT_
MIC
_L
N.C
. (M
F_LE
D)
REG_GND
MF_A
AU_2.8V
XF_TALLY_LED
REG_GND
KEY_AD6
A_4.6V
MF_B INT_MIC_R
INT_MIC_L
GND
GND
REG_GND
A_4.6V
AU_2.8V
XF_TALLY_LED
MF_B
MF_A
VA-117 BOARD(1/2)
MA-409BOARD
LB-077 BOARD
FP-437
FB-219BOARD
FP-4
44
FP-435FP-436
MIC(PLUG IN POWER)
VD
_SC
K
DR
UM
_VS
PB
_IN
_R
IC41
01_C
_OU
T
D_1
.5V
REG
_GN
D
AG
C_C
ON
T
FAS
T_C
HA
RG
E
A_4
.75V
MT_
GN
D
REG
_GN
D
MF_
B
HO
TSH
OE_
ID2
REC
_OU
T_L
MT_
GN
D
REG
_GN
D
BEE
P_I
N
IC16
01_1
.5V
BAT
T_S
IG
IC41
01_Y
_OU
T
DR
UM
_VS
DR
UM
_ER
RO
R
ZOO
M_M
IC_C
ON
T
KEY
_AD
6
BAT
T_U
NR
EG
D_1
.5V
AU
_LIN
E_I/
O_L
EVF_
G/B
W_Y
VD
_SO
RP
_4.7
5V
XC
S_I
C41
01
XC
S_A
U1
CA
M_-
6.5V
IC16
01_1
.5V
HS
_SC
K
HS
_HD
S
XV
SP
_SC
K
A_2
.8V
MF_
A
VC
O
XV
IDEO
_IN
BAT
T_X
EXT
INIT
_CH
AR
GE_
ON
IC21
01_C
_OU
T G
XF_
TALL
Y_L
ED
SIR
CS
_PW
M
SH
OE_
ON
HO
TSH
OE_
ID1
MT_
5V
VID
EO_I
/O
EXT_
MIC
_JA
CK
S_C
_I/O
EVF_
R
IC23
01_R
EVF_
B
SH
OE_
CO
NT_
AD
CA
M_D
D_O
N
XM
IC_M
ON
O
A_4
.75V
HS
_TX
D
D_2
.8V
CA
P_E
RR
OR
IC23
01_L
D_1
.9V
HS
_RX
D
EXT_
STR
OB
O
PLL
_1.5
V
IR_O
N
EP_1
3.3V
VTR
_UN
REG
REG
_GN
D
A_2
.8V
CA
P_V
S
XR
ST_
VTR
CA
P_V
S
PB
_IN
_L
PA
NEL
_XH
D
CA
M_1
2V
SD
C_I
N
IC21
01_Y
_OU
T
MF_
LED
XC
S_E
VF
PA
NEL
_XV
D
REG
_GN
D
SIR
CS
_SIG
REG
_GN
D
D_2
.8V
AU
_LIN
E_I/
O_R
S_V
_I/O
REG
_GN
D
REC
_OU
T_R
XA
UD
IO_I
N
VTR
_DD
_ON
VS
P_S
O
MT_
5V
LAN
C_S
IG
AC
C_C
ON
T
HP
_JA
CK
_IN
D_2
.8V
REC
_OU
T_R
S_C
_I/O
MF_
A
XF_
TALL
Y_L
ED
VS
P_S
O
AC
C_C
ON
T
CA
M_-
6.5V
REG
_GN
D
IC21
01_Y
_OU
T
D_2
.8V
XC
S_E
VF
XC
S_I
C41
01
DR
UM
_VS
PLL
_1.5
V
A_4
.75V
IC43
01_L
PB
_IN
_R
D_2
.8V
HO
TSH
OE_
ID2
XR
ST_
VTR
REG
_GN
D
SH
OE_
CO
NT_
AD
VD
_SO
EVF_
B
VC
O
IC41
01_Y
_OU
T
AU
_LIN
E_I/
O_L
XC
S_A
U1
EP_1
3.3V
EXT_
MIC
_JA
CK
VD
_SC
K
MF_
B
BAT
T_S
IG
VID
EO_I
/O
D_1
.9V
RP
_4.7
5V
IC43
01_R
MT_
5V
EVF_
R
A_4
.75V
FAS
T_C
HA
RG
E
DR
UM
_VS
CA
M_D
D_O
N
IR_O
N
D_1
.5V
REG
_GN
D
A_2
.8V
EXT_
STR
OB
O
IC41
01_C
_OU
T
REG
_GN
D
REG
_GN
D
EVF_
G/B
W_Y
CA
P_V
S
DR
UM
_ER
RO
R
SIR
CS
_SIG
HS
_RX
D
REG
_GN
D
IC16
01_1
.5V
AU
_LIN
E_I/
O_R
ZOO
M_M
IC_C
ON
TG
HO
TSH
OE_
ID1
REG
_GN
D
VTR
_UN
REG
HS
_SC
K
LAN
C_S
IG
IC16
01_1
.5V
REC
_OU
T_L
A_2
.8V
CA
P_E
RR
OR
MT_
GN
D
SD
C_I
N
PA
NEL
_XH
D
D_2
.8V
XM
IC_M
ON
O
BAT
T_U
NR
EG
HP
_JA
CK
_IN
CA
P_V
S
BEE
P_I
N
PB
_IN
_L
BAT
T_X
EXT
MF_
LED
PA
NEL
_XV
D
SH
OE_
ON
HS
_HD
S
SIR
CS
_PW
M
HS
_TX
D
KEY
_AD
6
XA
UD
IO_I
N
D_1
.5V
INIT
_CH
AR
GE_
ON
XV
SP
_SC
K
AG
C_C
ON
T
CA
M_1
2V
IC21
01_C
_OU
T
S_Y
_I/O
XV
IDEO
_IN
VTR
_DD
_ON
MT_
GN
D
MT_
5V
BT901
LCD903
VC-281 BOARD(2/3)
MIC901
H
2 3 129
G
11
E
C
10 14136
B
7
I
D
F
5 84
16
FLEXIBLEFLEXIBLE
INTELLIGENT ACCESSORY SHOE(15P)
FLEX
IBLE
(HEADPHONE)
FLEXIBLE
COLOR EVF UNIT
DC IN (BATTERY TERMINAL)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-5 4-6
FRAME SCHEMATIC DIAGRAM (3/3)
FRAME SCHEMATIC DIAGRAM (3/3)
28P
CN
1005
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
12P
CN
4004
123456789101112
2PCN5205
1SP(+)
2SP(-)
40P
CN
5202
12345678910111213141516171819202122232425262728293031323334353637383940
8PC
N52
04
1 2 3 4 5 6 7 8
8PCN5207
1 EXECUTE
2 GND
3 DIAL_A
4 DIAL_B
5 BACK_LIGHT
6 EXPOSURE
7 GND
8 GND
20P
CN
5203
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
24P
CN
5501
123456789101112131415161718192021222324
10PCN5601
1 LED_GND
2 LED
3 BL_LOW
4 N.C.
5 N.C.
6 N.C.
7 N.C.
8 N.C.
9 N.C.
10 BL_HIGH
6PC
N56
53
123456
8PC
N56
51
1 2 3 4 5 6 7 8
20P
CN
5652
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
20P
CN
5654
1234567891011121314151617181920
8PC
N00
1
12345678
18P
CN
5201
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
20P
CN
1008
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1
A
10P
CN
001
1 2 3 4 5 6 7 8 9 10
D901
KEY
_AD
3
PA
NEL
_G
XH
D_O
UT
HI_
XR
ESET
BAT
T_LI
_3V
MA
KER
_CH
ECK
KEY
_AD
2
VD
_SO
XR
ST_
VTR
PA
NEL
_XV
D
PA
NEL
_B
CO
M_O
UT
LCD
_CO
M/X
DAT
A
KEY
_AD
1
REG
_GN
D
PA
NEL
_R
XO
SD
_SC
K
XC
S_L
CD
KEY
_AD
4
VG
PA
NEL
_XH
D
DIA
L_A
XC
S_L
CD
_DR
IVER
OS
D_S
O
VD
_SC
K
EVER
_3.0
V
REG
_GN
D
DIA
L_B
BL_
CO
NT
PA
NEL
_4.7
5V SP
-
BL_
GN
D
PA
NEL
_-15
.3V
SE_
GN
D
PA
NEL
_13.
3V
BL_
REG
BL_
REG
BL_
GN
D
PA
NEL
_2.8
V
BL_
CO
NT
VD
_SC
K
PA
NEL
_R
HI_
EVER
_SO
PA
NEL
_XV
D
VD
_SO
XR
ST_
VTR
BL_
REG
KEY
_AD
2_P
MA
KER
_CH
ECK
PA
NEL
_B
HI_
EVER
_SC
K
PA
NEL
_B
XC
S_L
CD
PA
NEL
_XV
D
REG
_GN
D
PA
NEL
_G
KEY
_AD
4
PA
NEL
_-15
.3V
PA
NEL
_13.
3V
PA
NEL
_G
EVER
_3.0
V
LCD
_CO
M/X
DAT
A
KEY
_AD
1
XC
S_L
CD
_DR
IVER
KEY
_AD
3
HI_
EVER
_SC
K
EVER
_3.0
V
BL_
GN
D
SE_
GN
D
BL_
GN
D
SP
+
XH
D_O
UT
REG
_GN
D
PA
NEL
_-15
.3V
XC
S_L
CD
PA
NEL
_XH
D
BL_
REG
PA
NEL
_4.7
5V
EP_1
3.3V
PA
NEL
_XH
D
VD
_SO
VG
MA
KER
_CH
ECK
BL_
CO
NT
XH
D_O
UT
BL_
REG
SE_
GN
D
EP_2
.8V
CO
M_O
UT
PS
IG/P
AN
EL_C
OM
DIA
L_B
VD
_SC
K
PA
NEL
_2.8
V
SP
-
EP_4
.75V
DIA
L_A
BAT
T_LI
_3V
HI_
EVER
_SO
LCD
_CO
M/X
DAT
A
HI_
XR
ESET
XC
S_L
CD
_DR
IVER
XR
ST_
VTR
BL_
GN
D
REG
_GN
D
VG
KEY
_AD
2
PA
NEL
_R
VS
H3V VB
SP
D
EX1
SP
S
GN
D
CLS EX
2
PS
G
PS
S2
VG
L
MO
1
RES
VG
H
PS
S1
VR
VS
H5V
CTR
GN
D
CLDV
G
MO
2
VC
OM
VG
LAC
BL_
GN
D
PA
NEL
_B
PA
NEL
_REV
VD
_SC
K
XC
S_L
CD
_DR
IVER
PS
IG/P
AN
EL_C
OM
MA
KER
_CH
ECK
GN
D
BL_
REG
EP_1
3.3V
PA
NEL
_R
LCD
_CO
M/X
DAT
A
GN
D
GN
D
VG
PA
NEL
_XV
D
N.C
.
EP_4
.75V
HI_
EVER
_SO
PA
NEL
_-15
.3V
EVER
_3.0
V
XR
ST_
VTR
PA
NEL
_G
HI_
EVER
_SC
K
REG
_GN
D
BL_
CO
NT
VD
_SO
PA
NEL
_REV
XH
D_O
UT
EP_2
.8V
SE_
GN
D
KEY
_AD
2_P
XC
S_L
CD
PA
NEL
_XH
D
CO
M1
SEG
11
SEG
6
SEG
4
SEG
12
SEG
15
SEG
16
SEG
2
SEG
10
CO
M3
CO
M4
SEG
7
SEG
1
SEG
14
SEG
13
SEG
3
SEG
8
SEG
9
CO
M2
SEG
5
MS
_BS
MS
_VC
C
MS
_SC
LK
MS
_DIO
MS
_IN
SER
T
GN
D
GN
D
MS
_VC
CFP-442
CK-108BOARD
PD-161 BOARD
FP-434
MS
_PLA
Y
MP
EG_P
LAY
MS
_IN
DEX
MEM
OR
Y_M
IX
REG
_GN
D
MS
_-
DIS
PLA
Y
REG
_GN
D
MS
_+
VO
L_-
MEN
U
MS
_DEL
ETE
REC
END
_SEA
RC
H
VO
L_+
AU
DIO
_DU
B
PB
_ZO
OM
GN
D
MS
_VC
C
MS
_VC
C
REG
_GN
D
MS
_DIO
XP
HO
TO_F
REE
ZE
KEY
_AD
0
XV
TR_M
OD
E_S
W
XP
HO
TO_S
TBY
_SW
GN
D
ZOO
M_A
D
MS
_SC
LK
XC
AM
_STB
Y_S
W
MS
_IN
SER
T
D_2
.8V
AC
CES
S_L
ED
MS
_BS
REG
_GN
D
XS
/S_S
W
D_2
.8V
SP
+
LCD902
PANELREVERSE
LCD901
SHEET KEY
CONTROLSWITCH BLOCK(KP-CX2670)
VC-281 BOARD(3/3)
SP901
VA-117 BOARD(2/2)
H
2 3 12
J
9
G
11
E
C
10 14136
B
7
I
D
F
155 84
16
3.5INCH LCD UNIT
FLEXIBLE
CHARACTER DISPLAY UNIT
FLEXIBLEFP-441
CONTROLSWITCH BLOCK(SH-CX2670)
CONTROLSWITCH BLOCK(PS-CX2670)
MEMORYSTICKCONNECTOR
FLEXIBLE
FP-438
N.C
.
N.C
.
GN
D
GN
D
MS
_SC
LK
MS
_VC
C
MS
_IN
SER
T
MS
_VC
C
MS
_BS
MS
_DIO
ND901BACK LIGHT
(STARTER)
BT5201(LITHIUM BATTEY)
FLEXIBLE
PV-139 HARNESS(PV-136) (PV-135)
2.5INCH LCD UNIT:TRV27E:TRV24E/TRV25E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
LinkLink
4-2. SCHEMATIC DIAGRAMS
CD-366 BOARD (CCD IMAGER)
MA-409 BOARD (MIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCH)
LB-077 BOARD (EVF, EVF BACK LIGHT)
PD-161 BOARD (1/2)(RGB DRIVE, TIMING GENERATOR)
JK-217 BOARD (STEADY SHOT, A/D IN/OUT)
JK-218 BOARD (DIGITAL IN/OUT)
FB-219 BOARD (MANUAL FOCUS SENSOR)
CK-108 BOARD (SWITCH, CONNECTOR)
CONTROL SWITCH BLOCK (PS-CX2670)FP-100, FP-228, FP-102 FLEXIBLE BOARD (MODE SWITCH, DEW SENSOR, TAPE TOP/END SENSOR, S/T REEL)
VA-117 BOARD (6/6) (VIDEO I/O)
VA-117 BOARD (5/6) (CHARGE)
VA-117 BOARD (4/6) (DC-DC CONVERTER)
VA-117 BOARD (3/6) (MIC AMP)
VA-117 BOARD (2/6) (AUDIO)
VA-117 BOARD (1/6) (RGB DRIVE, TG)
PD-161 BOARD (2/2) (LCD DRIVE, BACK LIGHT)
FP-100, FP-228, FP-102 FLEXIBLE BOARD (MODE SWITCH, DEW SENSOR, TAPE TOP/END SENSOR, S/T REEL)
VA-117 BOARD (6/6) (VIDEO I/O)
VA-117 BOARD (5/6) (CHARGE)
VA-117 BOARD (4/6) (DC-DC CONVERTER)
VA-117 BOARD (3/6) (MIC AMP)
VA-117 BOARD (2/6) (AUDIO)
VA-117 BOARD (1/6) (RGB DRIVE, TG)
PD-161 BOARD (2/2) (LCD DRIVE, BACK LIGHT)
MA-409 BOARD (MIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCH)
PD-161 BOARD (1/2)(RGB DRIVE, TIMING GENERATOR)
JK-217 BOARD (STEADY SHOT, A/D IN/OUT)
JK-218 BOARD (DIGITAL IN/OUT)
FB-219 BOARD (MANUAL FOCUS SENSOR)
CK-108 BOARD (SWITCH, CONNECTOR)
CONTROL SWITCH BLOCK (PS-CX2670)
LB-077 BOARD (EVF, EVF BACK LIGHT)
CD-366 BOARD (CCD IMAGER)
WAVEFORMSCOMMON NOTE FOR SCHEMATIC DIAGRAMS WAVEFORMSCOMMON NOTE FOR SCHEMATIC DIAGRAMS
4-7
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS4-2. SCHEMATIC DIAGRAMS
Link(For schematic diagrams)• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolyticsand tantalums.
• Chip resistors are 1/10 W unless otherwise noted.kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.Example C541 L452
22U 10UHTA A 2520
• Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.
• Parts with differ according to the model/destination.Refer to the mount table for each function.
• All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.
• Signal nameXEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor• 5: fusible resistor• C: panel designation• A: B+ Line• B: B– Line• J : IN/OUT direction of (+,–) B LINE.• C: adjustment for repair.• A: VIDEO SIGNAL (ANALOG)• A: AUDIO SIGNAL (ANALOG)• A: VIDEO/AUDIO SIGNAL• A: VIDEO/AUDIO/SERVO SIGNAL• A: SERVO SIGNAL• Circled numbers refer to waveforms.(Measuring conditions voltage and waveform)• Voltages and waveforms are measured between the
measurement points and ground when camera shootscolor bar chart of pattern box. They are reference valuesand reference waveforms.(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon inputimpedance of VOM used.)
1. Connection
2. Adjust the distance so that the output waveform ofFig. a and the Fig. b can be obtain.
When indicating parts by reference number, pleaseinclude the board name.
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)
Kinds of capacitor
Temperature characteristicsExternal dimensions (mm)
Note : The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
Yello
w
A AB BA=B
Fig. a (Video output terminal output waveform)
H
Cya
nG
reen
Whi
teM
agen
ta
Red
Blu
e
Fig.b (Picture on monitor TV)
Front of the lens
Pattern box
1.5 m
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-2. SCHEMATIC DIAGRAMS
4-9 4-10 CD-366/LB-077
4-2. SCHEMATIC DIAGRAMS CD-366 BOARD LB-077 BOARD4-2. SCHEMATIC DIAGRAMS CD-366 BOARD LB-077 BOARD
For Schematic Diagram• Refer to page 4-71 for printed wiring board.• Refer to page 4-93 for waveforms.
P0R1.6
R0.6P0R0.6P0
R2.7P0
2.8
0.4
1.3
P0R1.1
R2.2P0
P0R2.2
63
0
P0R9.1
R8.
9P
0
P0
R1.
7
P0
R1.
9
P0
R13
.9
P0
R12
.2
R-7
.0/P
0
R-0
.4/P
0
R-0
.5/P
0
R-6
.9/P
0
R-7
.6/P
0.3
R9.
1/P
0
R15
.1/P
0
54
3
21
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
27PCN5101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
0R5102
B0.1u
C5105
100uHL5101
XXC5107
B0.1u
C5113
B0.1u
C5116
B0.1u
C5112
B16V0.1u
C5102
XXC5115
B0.1u
C5106
0R5101
10u6.3V
TA A
C5114
B0.1u
C5108
10uHL5102
UN9213J-(TX).SOQ5101
B0.1u
C5101
10u10V
TA A
C5111
ICX
427A
K-1
3IC
5101
1
V4
2
V3
3
V2
4
V1
5
VL
6
RC
SU
B
7
VD
D
8
CC
D_O
UT
9
GN
D
10
RG
11
H1
12
H2
13
GN
D
14
VS
UB
4.7u25VTA B
C5110
B0.1u
C5103
XXC5109
IC5102AD80017AJRURL
1CLPDM
2GND
3VDD
4OUT1
5OUT2
6GND
7BYP8 BYP
9 BYP
10 BYP
11 CCD_IN
12 GND
13 SHD
14 SHP
FB51010uH
LN5101
GND
6PCN5102
1
2
3
4
5
6
0uHFB5102
0uHFB5103
S201
XXD201
R2021500
S203
1A1
3A2
2B1
4B2R201
1200
S202
1A1
3A2
2B1
4B2
LND210
XXC5104
1
A
RCSUB
GND
CCD_OUT+
XEJECT_SW
VSUB
CCD-
V4
A_2.8V
155mA
GND
CCD+
RG
GND
V3
GND
XSHP
H2
GND
V1
XSHD
CAM_-7.5V
GND
GND
H1
CAM_15V
CLPDM
V2
CCD_OUT-
N.C.
XEJECT_SW
N.C.
KEY_AD0
KEY_AD0
N.C.
N.C.
N.C.
IC5102S/H
CCD IMAGER
IC5101
EDITSEARCH +
EDITSEARCH –
(EJECT SW)
FP-443 FLEXIBLE
TOVC-281 BOARD(1/16)CN1501
TROUGH THE FP-440 FLEXIBLE
(PAGE 4-37 of LEVEL3)
BUFFER
CD-366 BOARDCCD IMAGERXX MARK:NO MOUNT
16
YCHROMA Y/CHROMA
REC
PB
VIDEO SIGNAL
SIGNAL PATH
•
Precautions Upon Replacing CCD imager
with a CCD imager.•
In addition, ensure that the receiver is not covered with dusts
When replacing this board, remove the CCD imager from the
As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
nor exposed to strong light.
old one and mount it onto the new one.
If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
•
The CD-366 board mounted as a repair part is not equipped
G
E
8
F
5
C
3 742
B
6
D
H
2.8
0
4.7
0 4.7
0.3
0.3 4.7
0.4 1.0
0.3
1.41.0
NO MARK:REC/PB MODE
33kR6105
± 0.5%22
R6106NJM2125F(TE2)IC6101
12
3 45
16PCN6102
1 VDD
2 VSS
3 VST
4 VCK
5 STB
6 EN
7 DWN
8 RGT
9 HST
10 HCK2
11 HCK1
12 BLK
13 VB
14 VR
15 VG
16 COM
20PCN6101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
R6101XX
TH61016.8k
NSCW100-T39D6102
3300R6104
XXD6101
± 0.5%180k
R6102
2.2uF
C6102
HN1B04FE-Y/GR(TPLR3)Q6102
3
5
4 6
2
1
± 0.5%33k
R6103
RN4983FE(TPLR3)Q6101
3
5
4
6
2
1
C61010.1u
1
A
EVF_GND
EVF_VCC
XTALLY_LED
VB
VST
VG
EVF_GND
EVF_4.75V
BLK
VR
STB
LED_DA
EN
LED_ON/OFF
HST
EVF_GND
COM
VCC
HCK1
HCK2
VCK
LED BACKLIGHT DRIVER
IC6101 (BACKLIGHT)
LED DRIVE
LED SWITCH
TOVA-117 BOARD(1/6)CN4201
( THROUGHTHE FP-435 FLEXIBLE )
(PAGE 4-24)
LCD903
COLORLCD UNIT
EVF,EVF BACK LIGHTLB-077 BOARD
XX MARK:NO MOUNT
E
F
5
C
3 42
B
6
D
16VIDEO SIGNAL
YCHROMA
PB
SIGNAL PATH
REC
Y/CHROMA
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-11 4-12MA-409/FB-219
4-2. SCHEMATIC DIAGRAMS MA-409 BOARD FB-219 BOARD4-2. SCHEMATIC DIAGRAMS MA-409 BOARD FB-219 BOARD
For Schematic Diagram• Refer to page 4-75 for printed wiring board of MA-409 board.• Refer to page 4-77 for printed wiring board of FB-219 board.
4.6 4.6
NO MARK:REC/PB MODE
2.3 0.1
0.11.1
LN5901
A
B0.01u
C5901
FB5903 0uHJ5901
VD5902 VD5904
FB5904 0uH
CN5901 4P
1
2
3
4
24PCN5902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
8PCN5903
1
2
3
4
5
6
7
8
FB5901 0uH
VD5903
FB5902 0uH
VD5901J5902
CL-310IRS-X-TUD5902
47R5901
10u6.3VTA
C5902
CL-310IRS-X-TUD5901
MA111-(K8).S0D5903
SBX3055-01IC5901
12
4 3
XXD5904
1 23
D5905UDZSTE-178.2B
GP1S092HCPIPH6001
6PCN6001
1
2
3
4
5
6
GP1S092HCPIPH6002
SML-310LTT86D6001
330R6003
R60010
680R6002
R3011200
R3021500
S301
1A1
3A2
2B1
4B2
S302
1
2
3
4
1
A
INT_MIC_L
EXT_MIC_L
INT_MIC_R
EXT_MIC_R
HP_JACK_IN
HP_L_OUT
HP_R_OUT
EXT_MIC_L
EXT_MIC_R
HP_L_OUT
HP_JACK_IN
HP_R_OUT
INT_MIC_L
INT_MIC_R
XF_TALLY_LED
MF_B
MF_A
MF_A
MF_B
XF_TALLY_LED
KEY_AD6
KEY_AD6
SIRCS_SIG
XF_TALLY_LED
NS_LED_A
A_4.6V
NS_LED_K
INT_MIC_L
INT_MIC_R
GND
GND
A_4.6V
XF_TALLY_LED
HP_R_OUT
HP_L_OUT
HP_JACK_IN
INT_MIC_L
MIC_GND
AU_2.8V
MIC_GND
REG_GND
MF_A
MF_B
REG_GND
REG_GND
MF_A
MF_B
KEY_AD6
KEY_AD6
AU_2.8V
OUT VCC
GND GND
N.C. (MF_LED)
REG_GND
INT_MIC_R
MIC_GND
EXT_MIC_L
EXT_MIC_R
MIC_GND
REG_GND
A_4.6V
AU_2.8V
REG_GND
XF_TALLY_LED
MF_B
MF_A
L
R
MIC901
MIC(PLUG IN POWER)
(HEADPHONES)
REMOTE CONTROL RECEIVER
IC5901
TOVA-117 BOARD(3/6)CN4003
( THROUGH THEFP-437 FLEXIBLE )
(PAGE 4-27)
FADER FOCUS(INFINITY)
FP-444 FLEXIBLE
MANUAL FOCUS SENSORFB-219 BOARD
(TALLY)
SIGNAL PATH
PB
AUDIOSIGNAL
REC
H
2 3 129
G
11
E
C
106
B
7
D
F
5 84
I
MA-409 BOARDMIC IN,HP JACK,REMOTE CONTROL RECEIVER,SWITCHXX MARK:NO MOUNT
16
(NS LED)
(NS LED)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-13 4-14 JK-217/JK-218
4-2. SCHEMATIC DIAGRAMS JK-217 BOARD JK-218 BOARD4-2. SCHEMATIC DIAGRAMS JK-217 BOARD JK-218 BOARD
For Schematic Diagram• Refer to page 4-73 for printed wiring board of JK-217 board.• Refer to page 4-74 for printed wiring board of JK-218 board.
0R5304
VD5303
FB5310 0uH
FB53090uH
VD5304
VD5306
0R5302
0R5301
VD5301
VD5305
VD5302
01ZA8.2(TPL3)D5302
1 23
J5301
1 SIG
2 LANC_DC3 GND
4 232C_TD
5 JACK_IN
Y
GG
C
J5302
2 CGND
1 YGND
4 C
3 Y
6 S1
5 S2
7 V8 AUL
9 AUR10GND11S
XXC5302
XXC5301
LN5301
CH_GND
0R5303
UDZSTE-178.2BD5301
FB53010uH
FB53070uH
FB5308 0uH
FB53050uH
FB53040uH
FB53
020u
H
FB53030uH
20PCN5305
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0R5305
SE5302
1 234
SE5301
1 234
CN5351 5P
1VCC
2D-
3D+
4ID
5USB GND
S5351
1A
2B
10kR5352
R5355XX
UDZSTE-178.2BD5352
21
CL5351
CH_GND
12PCN5353
1
2
3
4
5
6
7
8
9
10
11
12
01ZA8.2(TPL3)D5351
1 23
R5354XX
CL5352
CH_GND
4PCN5352
1
2
3
4
LF53510uH
R5353XX
UDZSTE-178.2BD5353
21
1SS357(T3SONY1)D5354
LF53520uH
10kR5351
R5356XX
30PCN5354
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
A
V_JACK_IN
S_C_I/O
AUDIO_L_I/O
AUDIO_R_I/O
VIDEO_I/O
S_Y_I/O
XS_JACK_IN
S_GND
SE_2.8V
PS_V
LANC_SIG
REG_GND
REG_GND
XS_JACK_IN
PS_LI
AU_LINE_I/O_L
S_C_I/O
XLANK_JACK_IN
REG_GND
VIDEO_I/O
S_Y_I/O
AV_JACK_IN
REG_GND
YS_V
LANC_DC
REG_GND
AU_LINE_I/O_R
YS_LI
Vcc
Vout
Vref
GND
GND Vout
Vref Vcc
TPB
USB_DET
NTPA
TPA
REG_GND
REG_GND
KEY_AD5
TPA
REG_GND
USB_D+
TPB
REG_GND
NTPB
USB_D-
NTPB
NTPA
XLANK_JACK_IN
XS_JACK_IN
KEY_AD5
USB_GND->REG_GND
REG_GND
AU_LINE_I/O_L
PS_LI
YS_V
REG_GND
TPA
TPB
USB_D-
LANC_DC
AV_JACK_IN
S_C_I/O
YS_LI
VIDEO_I/O
NTPA
USB_D+
REG_GND
SE_2.8V
PS_V
AU_LINE_I/O_R
REG_GND
LANC_SIG
USB_VCC->USB_DET
REG_GND
NTPB
REG_GND
S_Y_I/O
(PITCH SENSOR)
(YAW SENSOR)
S VIDEO
AUDIO/VIDEO
LANC
XX MARK:NO MOUNT
JK-217 BOARDSTEADY SHOT,A/D IN/OUT
CHROMA
REC
Y SIGNAL
PB
Y/CHROMAAUDIO
VIDEO SIGNAL
SIGNAL PATH
(USB)
SUPER NS
DV IN/OUT
DV IN
: TRV25E/TRV27E
: TRV24E
XX MARK:NO MOUNT
DIGITAL IN/OUTJK-218 BOARD
FP-445 FLEXIBLE
TOVC-281 BOARD(12/16)CN1006
(PAGE 4-59)
H
2 3 12
J
9
G
11
E
C
10 14136
B
7
I
D
F
5 84
16
FP-445 FLEXIBLE is replaced as a block.So its PRINTED WIRING BOARD is omitted.
IN : TRV24EIN/OUT : TRV25E/
TRV27E
IN : TRV24EIN/OUT : TRV25E/
TRV27E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-15 4-16CK-108
4-2. SCHEMATIC DIAGRAMS CK-108 BOARD SIDE A CK-108 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS CK-108 BOARD SIDE A CK-108 BOARD SIDE B
For Schematic Diagram• Refer to page 4-81 for printed wiring board.
TOPD-161 BOARD(1/2)CN5652
(PAGE 4-19)
TOPD-161 BOARD(1/2)CN5651
(PAGE 4-19)
TOVC-281 BOARD(16/16)CN1005
(PAGE 4-68 of LEVEL3)
TOVA-117 BOARD(2/6)CN4004
(PAGE 4-25)
THROUGHTHE PV-135 HARNESS
)THROUGH THEPV-136 HARNESS(
2PCN5205
1SP(+)
2SP(-)
01ZA8.2(TPL3)D5205
1 2
301ZA8.2(TPL3)
D5206
1 2
3
LN5202
CH GND
40PCN5202
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
18PCN5201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S520712
34
3900R5219
3900R5220
1200R5209
2200R5217
1500R5213
LN5201
CH GND
D520101ZA8.2(TPL3)
1 2
3
D52
03U
DZS
TE-1
78.2
B 2
1
S5203
1
3
2
401ZA8.2(TPL3)D5204
1 2
3
1kR5201
8PCN5204
1
2
3
4
5
6
7
8
20PCN5203
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
S5201
1
3
2
4
S5202
1
3
2
4
S5204
1
3
2
4
S5205
1
3
2
4
S5206
1
3
2
4
8200R5223
8200R5226
BT5201
C5201XX
C5202XX
8PCN5207
1
2
3
4
5
6
7
8
0R5227
XXC5203
0R5228
XXD5208
XXD5207
S114
1
3
2
4
S102
1
3
2
4
S110
1
3
2
4
S108
1
3
2
4
S116
1
3
2
4
S111
1
3
2
4
S113
1
3
2
4
S107
1
3
2
4
S103
1
3
2
4
S115
1
3
2
4
S101
1
3
2
4
S105
1
3
2
4
S109
1
3
2
4
S104
1
3
2
4
S106
1
3
2
4
S112
1
3
2
4
S102,103
S100
1
2
3
4
5
6
7
8S101
28PCN002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
40PCN001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
12PCN003
1
2
3
4
5
6
7
8
9
10
11
12
1200R5206
8200R5221
1200R5207
1500R5212
2200R5215
3900R5218
1500R5211
2200R5216
8200R5224
1500R5210
1200R5208
27kR5225
2200R5214
3900R5222
1
A
KEY_AD1
MS_PLAY
MS_-
DISPLAY
VOL_-
MS_INDEX
MS_+
END_SEARCH
VOL_+
MS_DELETE
MEMORY_MIX
KEY_AD2
MENU
AUDIO_DUB
HI_XRESET
DIAL_A
HI_EVER_SO
PANEL_R
DIAL_B
XCS_LCD
VD_SO
PANEL_XVD
KEY_AD1
HI_EVER_SCK
XHD_OUT
XCS_LCD_DRIVER
COM_OUT
LCD_COM/XDATA
VG
EVER_3.0V
VD_SCK
PANEL_G
PANEL_XHD
MAKER_CHECK
HI_XRESET
XCS_LCD
PANEL_G
EVER_3.0V
HI_EVER_SO
VD_SO
PANEL_R
VG
HI_EVER_SCK
XRST_VTR
XHD_OUT
PANEL_XVD
COM_OUT
XCS_LCD_DRIVER
LCD_COM/XDATA
PANEL_XHD
MAKER_CHECK
PANEL_B
KEY_AD4_A
MS_-
MS_+
MEMORY_MIX
MS_DELETE
MS_INDEX
MS_PLAY
KEY_AD1
KEY_AD1
KEY_AD4
KEY_AD2_A
DIAL_A
DIAL_B
XRST_VTR
VD_SCK
KEY_AD3
KEY_AD2_A
AUDIO_DUB
MENU
KEY_AD2
KEY_AD2
VOL_-
DISPLAY
END_SEARCH
VOL_+
KEY_AD3
KEY_AD3
KEY_AD4_A
KEY_AD2
KEY_AD3
KEY_AD4
PANEL_B
DIAL_B
DIAL_A
EXECUTE
GND
GND
XHD_OUT
KEY_AD1
KEY_AD2
BATT_LI_3V
PANEL_R
REG_GND
LCD_COM/XDATA
HI_EVER_SCK
DIAL_A
COM_OUT
PANEL_XHD
XCS_LCD_DRIVER
KEY_AD4
PANEL_B
XRST_VTR
VG
HI_EVER_SO
DIAL_B
MAKER_CHECK
XCS_LCD
EVER_3.0V
PANEL_G
HI_XRESET
VD_SCK
VD_SO
REG_GND
KEY_AD3
PANEL_XVD
BL_REG
BL_CONT
BL_GND
EP_4.75V
EP_2.8V
EP_13.3V
SE_GND
PANEL_-15.3V
MAKER_CHECK
VD_SCK
XRST_VTR
XHD_OUT
PANEL_XHD
HI_EVER_SCK
REG_GND
KEY_AD2_P
HI_EVER_SO
VD_SO
XCS_LCD
EVER_3.0V
PANEL_XVD
PANEL_R
PANEL_G
PANEL_B
LCD_COM/XDATA
PSIG/PANEL_COM
VG
XCS_LCD_DRIVER
SP-
SE_GND
PANEL_-15.3V
BL_GND
PANEL_13.3V
BL_CONT
BL_REG
BL_GND
PANEL_2.8V
BL_REG
PANEL_4.75V
SP+
MS_DELETE
DISPLAY
MS_INDEX
MEMORY_MIX
REG_GND
VOL_-
MS_+
PB_ZOOM
MPEG_PLAY
END_SEARCH
REC
MS_PLAY
MENU
VOL_+
REG_GND
MS_-
AUDIO_DUB
(MPEG_PLAY)
BACK_LIGHT
EXPOSURE
(EXECUTE)
(BACK_LIGHT,EXPOSURE)
(PB_ZOOM)
(REC)
(REC)
(PB_ZOOM)
(MPEG_PLAY)
GND
(BACK_LIGHT,EXPOSURE)
(EXECUTE)
MEMORY PLAYMPEG
DISPLAY
ENDSEARCH
AUDIO DUB
MEMORY –
VOLUME +INDEXMEMORY+
MEMORY MIX
MEMORY DELETE
VOLUME –REC
MENU PLAY ZOOM
EXECUTE
DIAL_B
GND
GND
EXEC
DIAL_A
BACK_LIGHT
GND
GND
EXPOSURE
OSD_SO
BL_REG
MAKER_CHECK
COM_OUT
SP+
XOSD_SCK
PANEL_R
KEY_AD2
HI_XRESET
XHD_OUT
SE_GND
PANEL_G
BATT_LI_3V
PANEL_XVD
REG_GND
BL_GND
HI_XRESET
VD_SCK
DIAL_A
KEY_AD4
XRST_VTR
REG_GND
PANEL_4.75V
BL_GND
VD_SO
DIAL_B
EVER_3.0V
PANEL_XHD
XCS_LCD
DIAL_B
LCD_COM/XDATA
PANEL_-15.3V
BL_REG
BL_CONT
PANEL_B
VG
BATT_LI_3V
KEY_AD3
PANEL_13.3V
DIAL_A
PANEL_2.8V
XCS_LCD_DRIVER
SP-
KEY_AD1
REC
XHD_OUT
HI_EVER_SCK
PANEL_R
SP+
PANEL_-15.3V
MAKER_CHECK
XRST_VTR
PANEL_XVD
PANEL_2.8V
PANEL_XHD
PANEL_4.75V
LCD_COM/XDATA
SE_GND
PANEL_G
BL_CONT
KEY_AD3
PANEL_B
BL_GND
COM_OUT
BL_REG
SP-
PANEL_13.3V
KEY_AD2
EVER_3.0V
BL_REG
KEY_AD4
HI_EVER_SO
VD_SO
BL_GND
KEY_AD1
VD_SCK
REG_GND
XCS_LCD
REG_GND
VG
XCS_LCD_DRIVER
STOP REW PLAY FF PAUSE
RESET
S103
EXPOSURE LIGHT
SEL/PUSH EXEC
S102
(PANEL OPEN/CLOSE)
CONTROL SWITCH BLOCK(KP-CX2670)
SP901SPEAKER
FP-434 FLEXIBLE
CONTROL SWITCH BLOCK(SH-CX2670)
CK-108 BOARDSWITCH,CONNECTORXX MARK:NO MOUNT
REC
SIGNALCHROMA
VIDEO SIGNAL
PB
SIGNAL PATH
Y Y/CHROMAAUDIO
H
2 3 12
J
179
G
11
E
C
10
K
14136
B
7
I
D
18
F
155
L
84 16
16
CONTROL SWITCH BLOCK(SH-CX2670)is replaced as a block.So that this PRINTED WIRING BOARD is omitted.
CONTROL SWITCH BLOCK(KP-CX2670)is replaced as a block.So that this PRINTED WIRING BOARD is omitted.
(SECONDARY)(LITHIUM BATTERY)
(TRV25E/TRV27E)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-17 CONTROL SWITCH BLOCK (PS-CX2670)4-18
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
S071 RV001
S1
S2
SML-310LTT86D001
8PCN001
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
10PCN001
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
A
GND
MS_DIO
D_2.8V
MS_VCC
REG_GND
ZOOM_AD
KEY_AD0
MS_INSERT
MS_BS
MS_SCLK
REG_GND
GND
XPHOTO_FREEZE
MS_VCC
ACCESS_LED
XS/S_SW
XVTR_MODE_SW
XCAM_STBY_SW
XPHOTO_STBY_SW
D_2.8V
GND
MS_BS
MS_VCC
MS_SCLK
MS_INSERT
GND
MS_VCC
MS_DIO
GND
MS_VCC
MS_INSERT
GND
MS_INSERT
MS_BS
MS_VCC
MS_DIO
GND
MS_SCLK
MS_DIO
MS_BS
MS_VCC
N.C.
MS_VCC
GND
N.C.MS_SCLK
TOVC-281 BOARD(16/16)CN1008
(PAGE 4-68 of LEVEL3)
PHOTO T W
(ZOOM)
POWER
MEMORY
CAMERA
OFF(CHG)
VCR
PLAYER
START/STOP
CONTROL SWITCH BLOCK(PS-CX2670)
FP-438 FLEXIBLE
MEMORY STICKCONNECTOR
2 3 9
E
C
6
B
7
D
5 84
16
CONTROL SWITCH BLOCK(PS-CX2670),FP-438 FLEXIBLE arereplaced as a block.So that there PRINTED WIRING BOARD are omitted.
(TALLY)
: TRV25E/TRV27E
: TRV24E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-19 4-20PD-161 (1/2)
4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD
For Schematic Diagram• Refer to page 4-77 for printed wiring board.• Refer to page 4-93 for waveforms.
3
2
1
6
5
4
1.7
1.8
1.8
1.8
1.4
13.8
2.3
2.3
13.8
6.9
1.4
2.7
R1.
1/p0
1.4
0.2
2.3
1.7
4.7
R0.
7/p0
1.7
1.7
2.7
2.7
2.6
2.8
2.8
1.1
1.6
2.8
4.7
2.8
1.4
1.4
1.4
P2.
8R
3.1
2.8
P2.3
P1.4
R0.1
R2.8
1.4
2.8
2.7
P2.8R0.1
2.6
R1.4
2.6
P0.1
2.6
8
P2.
4R
2.8
P1.4R0.4
R0.5P2.8
0.2
2.6
2.7
P1.3R1.4
2.8
P2.8R2.4
2.8
1.4
2.8
9
7P0
1.4
R2.3
P2.0R2.7
1.4
P2.8
P2.8
R0
R0
P2.8R0
2.8
2.7
0
2.8
2.8
1.4
4.7
13.8
-15.9
0
0
4.7 13.2
-15.9
3.4
2.8 -15.2
4.7
13.813.2
4.1
2.8
-15.2
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
:TRV24E/ TRV25E:TRV27E
:DCR-TRV27E:DCR-TRV24E/
TRV25E
:DCR-TRV27E:DCR-TRV24E/TRV25E
0.01uC5507
XXC5523
0.1u BC5517
1u BC5524
0.01uC5506
560p
CH
C55
11
XXR5518
0.1uB
C5512
24PCN5501
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
R552147k
0R5523
IC5502LZ9FF474
1
HD
I
2
HD
B
3
W/H
4
BL-
ON
5
BL-
DET
6
GN
D/T
ESTI
7
TES
TI/G
ND
8
LED
9
PW
M
10
TES
TI
11
TES
TI
12
CP
MO
DE/
CLS
13CP/SPS
14GRES/EX1
15GPCK/MODE1
16GSRT/MODE2
17STBYB/PSG
18RESET/EX2
21OE/PSS2
19VDD/RES
20SRT/PSS1
22CLR/CTR
23MCLK/CLD
24HCNT/SPD
25D
R.P
.SA
VE
26
OS
CO
27
OS
CI
28
XC
.SA
VE
29
PD
30
PS
/VD
D
31
GN
D
32
-IN
/TES
TO
33
+IN
/TES
TO
34
OU
T/TE
STO
35
SY
F
36
PO
CB
37 BGP
38 SWCOM
39 SW
40 FRP
41 COM_FRP
42 XSCK
45 SO
44 XCS
43 VDD/TESTI
46 SI
47 VSYB
48 XVD
0.01uC5505
10uC5514
TA6.3V
AA
XXR5520
1MR5513
D55021SV290(TPL3)
XXR5514
22kR5509
DETIN
XXR5528
FB55010uH
± 0.5%68k
R5503
FB5502 0uH
LED
MA111-(K8).S0D5503
68kR5510
L5502 XX
Q5503HN1B04FE-Y/GR(TPLR3)
3
5
46
2
1
1uB
C5521
Q5504HN1B04FE-Y/GR(TPLR3)
3
5
4 6
2
1
RN1104F(TPL3)Q5505
BL_ON
0.01uB
C5527
0.001uB
C5515
XXR5525
1MR5533
L550110uH
1kR5534
MGSF1P02LT1Q5502
100kR5532
XXC5503
180kR5531
0.01uB
C5530
C5532XX
470kR5501
XXR5529
0.1u BC5518
XXR5530
0.01uB
C5531
15kR5505
L55036.8uH
0.01uB
C5510
XXC5522
0.1u BC5519
0.01uB
C5504
C5509
20V1u
0.01uB
C5513
0R5515
47kR5507
IC5501CXA3592R-T4
1
N.C
.
2
N.C
.
3N
.C.
4
N.C
.
5
N.C
.
6
N.C
.
7
BIA
S
8
OP
_IN
+
9
OP
_IN
-
10
OP
_OU
T
11
VC
O
12
N.C
.
13N.C.
14N.C.
15Vcc4
16VSH
17GND1
18GND2
21G_DC_DET
19R_DC_DET
20VR
22VG
23B_DC_DET
24VB
25
Vcc
2
26
Vcc
3
27
CO
M_O
UT
28
N.C
29
CO
M_F
RP
30
FRP
31
GN
D3
32
BLA
CK
_IN
33
BG
P
34
N.C
.
35
EXT_
DA
1
36
R_I
NJE
CT
37 EXT_DA2
38 XC.SAVE
39 XSCK
40 SI
41 XCS
42 Vcc1
45 XP.SAVE
44 LPF_ADJ
43 TRAP_ADJ
46 B_IN
47 G_IN48 R_IN
XXR5517
100kR5512
R55190
XXR5502
DAC
68kR5508
2700R5506
1MR5511
*CH
C5516
10kR5516
RB5501100
FB5503 0uH
RB55021M
RB550310k
D5504XX
16V6.8u
C5520
TA
C5528
AA20V1u
C55080.1u
R5552*
1kR5591
C5501
6.3V10u
100kR5540
100kR5541
HI_EVER_SCK
BL_GND
XCS_LCD_DRIVER
6PCN5653
1
2
3
4
5
6
BL_CONT
LCD_COM/XDATA
BL_REG
8PCN5651
1
2
3
4
5
6
7
8
EP_4.75V
EVER_3.0V
SE_GND
CN5652 20P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
HI_EVER_SO
EP_2.8V
REG_GND
S001
1
A
TG14
TG16
TG15
TG13
XCS_LCD VR
VB
VD_SCK
TG18
TG16
TG15
TG14
TG13
CO
M_F
RP
FRP
BG
P
XP.SAVE
BGP
VD_SCK
XCS_LCD
VD_SO
PANEL_XHD
XHD_OUT
FRP
BLK
XP.
SA
VE
XC.SAVE
XTG_SO
TG18
TG20
TG21
TG22
TG24
COM_FRP
XTG_SO
TG24
BLK
VB
VG
TG23
TG22
TG20
TG21
TG19
TG17
TG17
TG12
TG12
TG19
XC
.SA
VE
TG23
PANEL_XVD
VG
VR
VD_SCK
XCS_LCD
VD_SO
PANEL_XVD
PANEL_XHD
XHD_OUT
CLS
VGLAC
CLD
PSS1
PSS2
EX1
MO2
RES
EX2
VB
VG
VR
VGL
SPS
VSH5V
MO1
GND
VSH3V
GND
VCOM
CTR
VGH
PSG
SPD
IC5501RGB DRIVE
TIMING GENERATOR
IC5502PANEL_REV
GND
PANEL_REV
PANEL_XVD
PSIG/PANEL_COM
EP_2.8V
BL_REG
PANEL_R
XCS_LCD_DRIVER
GND
VD_SO
MAKER_CHECK
BL_GND
PANEL_XHD
VG
PANEL_G
EP_4.75V
XRST_VTR
XCS_LCD
LCD_COM/XDATA
GND
REG_GND
EP_13.3V
BL_CONT
KEY_AD2_P
EVER_3.0V
SE_GND
N.C.
XHD_OUT
VD_SCK
PANEL_-15.3V
PANEL_B
HI_EVER_SO
HI_EVER_SCK
LCD9012.5INCH
3.5INCHCOLORLCD UNIT
SWITCH
SWITCHSWITCH
B+ SWITCH
TOCK-108 BOARDCN5204
THROUGHTHE PV-136 HARNESS
(PAGE 4-16)
(PAGE 4-16)
THROUGHTHE PV-135 HARNESS
TOCK-108 BOARDCN5203
FP-442FLEXIBLE
(PANELREVERSE SW)
H
2 3 12
J
179
G
11
E
C
10
K
14136
B
7
I
D
18
F
155
L
84 16
XX MARK:NO MOUNT
RGB DRIVE,TIMING GENERATORPD-161 BOARD(1/2)
REC
SIGNAL PATH
PB
CHROMA Y/CHROMA
VIDEO SIGNAL
Y
16
1 (2/2)
(2/2)2
3 (2/2)
R555256002200
C5516100P 68P
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-21 4-22 PD-161 (2/2)
4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD
For Schematic Diagram• Refer to page 4-77 for printed wiring board.• Refer to page 4-93 for waveforms.
2.0
1.5
1.6
1.5
1.50
10
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
3.0
3.0
0
3.0
3.0
3.0
2.8
2.8
0
0
1.8
4.8 4.8
4.7
4.7
1.52.8
0.3
0
0.34.7
-0.7-0.7
2.8
1.7
2.8
NO MARK:REC/PB MODE
(DCR-TRV24E/TRV25E)
:DCR-TRV24E/TRV25E:DCR-TRV27E
LED
D56
02P
G11
12H
-TR
R5609 XX
BL_REG
MA111-(K8).S0D5601
EP_2.8V
L56010uH
IC5601TC7W53FU(TE12R)
1 COM
2 INH
3 VEE
4 GND 5A
6CH1
7CH0
8VCC
EP_4.75V
R560322k
0.015uB
C5603
1/10W1800R5601
XXR5604
IC5602TA75S393F-TE85R
12
345
R5605120
BL_GND
0.1uB
C5605
DETIN
DAC
R5608 XX
10PCN5601
1 LED_GND
2 LED
3 BL_LOW
4 N.C.
5 N.C.
6 N.C.
7 N.C.
8 N.C.
9 N.C.
10 BL_HIGH
D5604 XX
B
C56040.1u
BL_ON
R5602180k
BL_CONT
XXD5603LD5605
A
C560612p
SL
470R5607
22kR5606
Q5603RN4983FE(TPLR3)
3
5
4
6
2
1
T5601
1
2
3
4
5
6
10
4.7uB
C5607
*R5613
R5614 XX
RN1104F(TPL3)Q5601
10kR5612
XXQ5604
Q5605CPH5504-TL-E
5
1
2
4
3
XCS_LCD_DRIVER
HI_EVER_SCK
HI_EVER_SO
LCD_COM/XDATA
20PCN5654
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
BU9735K-E2IC5651
1 OSC1
2 OSC2
3 VSS
4 VC
5 VLCD
6 VDD
7 SCK
8 SO
9
XC
S
10
C/X
D
11
CO
M1
12
CO
M2
13
CO
M3
14
CO
M4
15
SEG
1
16
SEG
2
17SEG3
18SEG4
19SEG5
20SEG6
21SEG7
22SEG8
23SEG9
24SEG10
25
SEG
11
26
SEG
12
27
SEG
13
28
SEG
14
29
SEG
15
30
SEG
16
31
SEG
17
32
SEG
18
REG_GND
680kR5652
270R5651
EVER_3.0V
VD5651
ND901
D901
1
A
SE_GND
SEG10
SEG
15
SEG9
SEG12
SEG4
SEG4
SEG
1
SEG
11
CO
M3
COM2
CO
M2
COM3
SEG1
SEG15
SEG7
SEG10 SEG3
SEG14
SEG5
SEG3
SEG11
SEG16
SEG
14
SEG13
SEG
13
SEG6
CO
M1
COM4
COM1
SEG5
SEG
12
SEG6
SEG
16
CO
M4
SEG7
SEG
2
SEG8
SEG2
SEG9
SEG8
VCC
SELECT SWITCH
IC5601
IC5602CURRENT DETECT
COM2
SEG1
SEG13
SEG3
SEG9
COM4
SEG5
SEG16
COM1
LCD DRIVE
SEG2
SEG6IC5651
SEG7
SEG14
SEG12
SEG11
COM3
SEG4
SEG15
SEG8
SEG10
LCD902CHARACTER DISPLAY
FP-441FLEXIBLE
BACKLIGHT
(STARTER)
SWITCHING
LED DRIVE
INV
2
G
5
E
3
F
4
C
9
D
I
B
8 11
H
76 10
XX MARK:NO MOUNT
PD-161 BOARD(2/2)LCD DRIVE,BACKLIGHT
16
2 (1/2)
(1/2)1
3 (1/2)
INVERTERTRANSFORMER
R561310K18K
12
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-23 4-24VA-117 (1/6)
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
For Schematic Diagram• Refer to page 4-85 for printed wiring board.• Refer to page 4-94, 95 for waveforms.
TOLB-077 BOARDCN6101
THROUGH THEFP-435 FLEXIBLE( )
(PAGE 4-10)
2.8
2.8
1.7
2.6
2.2
2.6
2.7
2.8
0
2.8
6.40 2.
0
3.0
1.4
6.7
0.9
3.0
6.4
6.7
6.7
1.4
0.9
3.1
0
1.7
11
12
13
2.8
13.7
1.4
13.7
1.4
2.8
0.9
1.4
16
2.9
1.7
14
15
1.3
1.4
0
2.8
2.5
2.6
2.8
2.6
17
0.1
1.4
1.4
0
0
2.8
1.4
1.4
19
2.8
2.8
2.8
2.8
1.4
0.9
0.9
18
0.3
2.7
2.7
2.5
2.3
2.7
2.8
0.9
2.6
1.4
NO MARK:REC/PB MODE
6.8uHL4202
100R4212
2700
R42
05
B0.01uC4205
2.2uB
C4218
100R4214
0.01uB
C4208
FB42010uH
C42171u
CXD3501AR-T4IC4202
1
HD
2
HD
O
3
XW
RT
4
CM
PO
5
DET
IN
6
GN
D
7
TES
TI
8
LED
9
PW
M
10
-IN
11
+IN
12
TES
T
13N.C.
14VST
15VCK
16STB
17EN
18DCG/CLR
21HST
19VDD
20RGT
22HCK2
23HCK1
24BLK
25
XS
TBY
26
OS
CO
27
OS
CI
28
XC
SA
VE
29
RP
D
30
TES
T
31
GN
D
32
SH
A
33
SH
B
34
SH
G
35
SH
R
36
XC
LR
37 XCLP
38 TEST
39 SBLK
40 FRP
41 TEST
42 XSCK
45 SO
44 XCS
43 VDD
46 SI
47 VDO
48 XVD
68kR4209
B0.01uC4204
0.1uB
C4210
1MR4210
PANEL_XHD
68kR4207
VD_SCK
R4204XX
100kR4211
PANEL_XVD
VD_SO
47kR4206
C4203XX
XCS_EVF
560pCH
C4209
L420110uH
22kR4208
100R4213
C42161u
1SV290(TPL3)D4201
4.7u20V
C4211
0R4203
EP_13.3V
120pCH
C4214
REG_GND
0.01u
B
C4213
16V
XXC4202 CXA3289AR-T4
IC4201
1
XS
H.S
AV
E
2
SH
_R
3
SH
_G
4
SH
_B
5
SH
_A
6N
.C.
7
BIA
S
8
OP
_IN
+
9
OP
_IN
-
10
OP
_OU
T
11
VC
O
12
CO
M_D
C
13COM_IN
14COM_OUT
15Vcc3
16VREF
17GND1
18GND2
21G_DC_DET
19R_DC_DET
20VR
22VG
23B_DC_DET
24VB
25
Vcc
2
26
P_D
C_D
ET
27
VP
28
XV
P.S
AV
E
29
PFR
P
30
FRP
31
PR
G
32
BLA
CK
_IN
33
BG
P
34
N.C
.
35
EXT_
DA
36
R_I
NJE
CT
37 N.C.
38 XC.SAVE
39 XSCK
40 SI
41 XCS
42 Vcc1
45 XP.SAVE
44 LPF_ADJ
43 TRAP_ADJ46 B_IN
47 G_IN
48 R_IN
VCO
470kR4201
± 0.5%100k
R4202
0.001uB
C4212
XXC4223
C42151u
G
B0.01uC4206
EP_2.8V
XRST_VTR
0R4221
0R4222
EP_4.75V
20PCN4201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
FB42020uH
R4215XX
R4220XX
R4219XX
R4218XX
2.2uF
C4219
0.5%
R421647k
±
±
0.5%1M
R4217
C4207XX
C42014.7u
CL4201
0R4223
1
A
EVF_B
EVF_G/BW_Y
EVF_R
R4224 1k
PANEL_XVD
BGP
XP_SAVE
XC_SAVE
BG
P
SB
LK
FRP
XCS_EVF
TG24
TG21
SH
R
SH
G
SH
B
SH
A
SH
A
SH
B
SH
G
SH
R
PANEL_XHD
XP
_SA
VE
XC
_SA
VE
SBLK
FRP
TG15
TG14
TG16
TG17
VCO
VD_SO
VD_SCK_EVF
XCS_EVF
XTG_SO
EVF_B
VCO
PANEL_XHD
XCS_EVF
VD_SO
VD_SCK_EVF
TG23
TG22
EVF_G/BW_Y
EVF_R
TG24
TG21
TG22
TG23
TG17
TG16
TG15
G
XRST_VTR
TG14
VD_SCK_EVF
XTG_SO
XRST_VTR
EVF_R
EVF_G/BW_Y
EVF_B
G
PANEL_XVD
EVF_GND
VCK
HST
EN
VR
COM
HCK1
XTALLY_LED
EVF_4.75V
HCK2
VG
LED_ON/OFF
VB
LED_DA
BLK
VST
EVF_VDD
STB
EVF_GND
EVF_GND
TA A
RGB DRIVE
IC4201
IC4202TIMING GENERATOR
RGB DRIVE,TG(VF BLOCK)XX MARK:NO MOUNT
VA-117 BOARD(1/6)
9
G
K
E
8 15
F
5
J
C
143 7 114 13
I
2
B
6 10 12
L
D
H
16
VIDEO SIGNAL
REC
Y
PB
CHROMA
SIGNAL PATH
Y/CHROMA
(4/6)1
2 (6/6)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-25 4-26 VA-117 (2/6)
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
For Schematic Diagram• Refer to page 4-85 for printed wiring board.
TOFP-434 FLEXIBLECN003
(PAGE 4-15)
4.7
0
2.4
2.4
0
0
2.4
2.4
4.7
R1.0/P0.3
R1.9/P0
P0.5R1.9
P0R1.9
P0.5R1.9
0.1
2.5
2.7
2.8
2.4
1.6
1.6
3.3
1.8
1.6
1.8
1.8
2.8
2.3
R
1.6
1.4
1.4
1.6
2.8
1.6
1.6
R1.8P0
R1.9P0.4
0
2.42.4
0.10.1
2.4 2.4
2.7
0.1
0 -0.4 -0.4
00
4.2
8.23.3
-0.5 -0.5
0
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
XCS_AU1
AU_4.75V
AU_LINE_I/O_L
AU_2.8V
0.01uB
C4314
10u6.3V
ATA
C4305
4V47u
C4324
4V47u
C4323
AU_LINE_I/O_R
TA
10u
A6.3V
C4318
220kR4302 10u
6.3VATA
C4328
3900R4303
10u6.3V
ATA
C4327
33kR4301
TA
10u
A6.3V
C4311
15u4V
C4316
A
B0.1u
C4310
10uA6.3V
C4322
VTR_UNREG
B1uC4307
0.01uB
C4312
B1u
C4306
B0.1u
C4309
B1u
C4317
XAUDIO_IN
BEEP_IN
B1u
C4315
VSP_SO
1uB
C4325
XVSP_SCK
1u BC4326
2SD1834-T100Q4301
1uB
C4308
1uB
C4302
L430110uH
B1u
C4304
B1uC4303
FB43010uH
A4V
TA
4.7uC4319
RN2111F(TPL3)Q4306
RN1104F(TPL3)Q4304
XXC4313
MIC_R
MIC_L
RN2910FE(TPLR3)Q4303
6
2
1
3
5
4
0.22u BC4321
10uA6.3V
C4320RN1910FE(TPLR3)
Q4307
3
5
4
6
2
1
RN1910FE(TPLR3)Q4305
6
2
1
3
5
4XX
Q4302
47kR4308
47kR4309
2200R4307
2200R4306
1kR4311
1kR4310
10kR4304
10kR4305
REG_GND
LA74207W-TBM-EIC4301
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1718
1920
2122
2324
2526
2728
2930
3132
33343536373839404142434445464748
4950
5152
5354
5556
5758
5960
6162
6364
REC_OUT_L
REC_OUT_R
PB_IN_L
PB_IN_R
C4301XX
IC4301_L
IC4301_R
HP_L_OUT
HP_R_OUT
47R4316
47R4318
47R4319
47R4317
PANEL_-15.3V
BL_REG
REG_GND(BL_GND)
EP_13.3V
EP_2.8V
12PCN4004
1
2
3
4
5
6
7
8
9
10
11
12
BL_CONT
EP_4.75V
REG_GND
REG_GND
1
A
XC
S_A
U1
XV
SP
_SC
K
VS
P_S
O
PANEL_-15.3V
EP_2.8V
EP_4.75V
EP_13.3V
BL_REG
VSP_SO
XVSP_SCK
XCS_AU1
BL_REG
PANEL_-15.3V
EP_13.3V
EP_4.75V
EP_2.8V
LINE2_OUT(R)
LPF_IN(L)
Vcc(M)
LINE1_OUT(R)
ALC_OUT(L)
MU
TE
MIC
_CTL
2(R
)
INT_
MIC
_Vcc
LPF_IN(R)
HP_OUT(L)
XC
S_A
U
MIC
_EX
T/IN
T
ALC_OUT(R)
Vcc
(D)
VS
P_S
O
VR
EFS
XV
SP
_SC
K
EXT_
MIC
(L)
LINE1_IN(L)
MIC
_OU
T(L)
AGC_TC
D_G
ND
XMIC_P_SAVE
MIC_IN(R)
Vcc(H)
MIC
_IN
(L)
LINE2_IN(R)
REC_OUT(L)
MIC
_GN
D
Vcc(L)
VREFM
INT_
MIC
(R)
MIC
_OU
T(R
)
EXT_
MIC
_Vcc
SP
_Vcc
VREFH
PB_IN(R)
EXT_MIC(R)
SP
_OU
T-
HP
_OU
T(R
)
INT_
MIC
(L)
MIX
_OU
TM
IC_M
ON
O
SP
_GN
D
LINE2_OUT(L)
BEE
P_I
N
MIC
_CTL
2(L)
HP
_CO
M
SP
_IN
MIC_DET1
LINE1_IN(R)
POWER_MUTE
LINE1_OUT(L)
PB_IN(L)
SP
OU
T+
MIC
_DET
2
P.MUTE_TC
LINE2_IN(L)REC_OUT(R)
MIC
_CTL
1(L)
A_GNDA_GND
MIC
_CTL
1(R
)
A_GND
BL_CONT
BL_GND
SP-
PANEL_2.8V
PANEL_-15.3V
PANEL_4.75V
BL_GND
SE_GND
PANEL_13.3V
SP+
BL_REG
BL_REG
REC
PB
AUDIO
SIGNAL PATH
SIGNAL
16
9
G
E
8
F
5
C
143 7 114 132
B
6 10 12
D
H
AUDIO(AU BLOCK)VA-117 BOARD(2/6)
XX MARK:NO MOUNT
AUDIO IN/OUT
IC4301MUTE
MUTING
AUDIO I/O SWITCH
SWITCH
(6/6)3
(4/6)4
(4/6)9
(6/6)6
(3/6)5
(4/6)8
(3/6)7
MUTE SWITCH
3.3V REG
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-27 4-28VA-117 (3/6)
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
For Schematic Diagram• Refer to page 4-85 for printed wiring board.
0.1
0.1
0.1
1.0
1.4
2.9
1.4
1.4
2.2
1.4
1.4
2.8
0
1.4
1.4
1.4
2.5
1.4
1.4
1.4
1.4
1.4
1.4
2.0
1.4
1.2
1.4
1.4
1.4
1.4
2.2
1.4
0.2
2.8
2.5
1.4
1.4
1.4
1.4
1.4
2.5
2.6
1.4
P0R3.0
1.4
2.8
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
12kR4424
B6800pC4404
1kR
4410
47kR4419
10kR4403
22kR4415
4700R4404
BH7870AKV-E2IC4401
1 2 3 4 5 6 7 8 9 10 11 12
1314
1516
1718
1920
2122
2324
252627282930313233343536
3738
3940
4142
4344
4546
4748
XXC4418
XXR4416
B0.01uC4430 B
6800pC4429
B0.1u
C4419
XXC4415
B0.001uC4414
B6800pC4402
22kR4417
2200R4406
2200R4401
2700R4402
XXC4431
XXR4414 B6800p
C4428
B0.01uC4426
1kR
4411
CH100p
C4412
XXC4424
XXR4413B
0.1uC4421
B0.022uC4401
100kR4425
CH100pC4417
2200R4407
CH100p
C4413
A6.3V10u
C4406
CH100p
C4416 B0.01uC4425
A6.3V10u
C4411
12kR4420
0.01uB
C4405
B0.022uC4403
MIC_R
REG_GND
100uHL4401
1uB
C4434
MIC_L
6800R4408
B0.1uC4420
TA
22u4V
A
C4432
XMIC_MONO
47kR4418
XXC4422
EXT_MIC_JACK
B0.01uC4427
XXC4407
ZOOM_MIC_CONT
B0.001uC4410
XXC4409
XX
*C4408
12kR4421
0R4405
6800R4409
0R4422
0.01uB
C4433
10kR4423
B0.047uC4435
B0.1uC4423
B0.047uC4437
3300R4427 XX
C4436
XXR4428
XXC4438
XXR4429
XXR4426
XXR4412
SHOE_MIC_L
XXR4431
AU_4.75V
AU_2.8V
0R4430
XXD4401
HP_R_OUT
XF_TALLY_LED
HP_L_OUT
24PCN4003
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MF_LED
MF_B
HP_JACK_IN
SIRCS_SIG
MF_A
A_4.75V
KEY_AD6
IR_ON
3300R4010
47R4011
MT_5V
0R4013
2SC5585H-T2LQ4003
RN1111F(TPL3)Q4001
47R4012
SIRCS_PWM
68R4009
REG_GND
REG_GND
1
A
HP_JACK_IN
HP_R_OUT
HP_L_OUT
XF_TALLY_LED
MF_LED
MF_B
SIRCS_SIG
MF_A
KEY_AD6
IR_ON
SIRCS_PWM
HP_R_OUT
HP_L_OUT
HP_JACK_IN
SIRCS_SIG
MF_LED
XF_TALLY_LED
MF_B
MF_A
KEY_AD6
SIRCS_PWM
IR_ON
N.C.
INV
T_O
UT_
L
EXT_
IN_R
N.C.
SU
B_S
IG_O
UT_
L
MO
DE_
CTL
_1
C_REG
AM
P_O
UT_
R
C_1/2VCC
SG
_IN
_R
INV
T_O
UT_
R
HP
F_O
UT_
L
SU
B_S
IG_O
UT_
R
HPF_AMP_IN_L
MTX
_AM
P_I
N_R
INT_
IN_L
MTX
_AM
P_O
UT_
R
SU
B_I
N_L
HP
F_O
UT_
R
GND
HP
F_A
MP
_IN
_R
ZOOM_AMP_OUT
HPF_ON/OFF
R_OUT
ZOOM_AMP_IN
REG
_2.5
V
MIC_MONO
MIX_OUT
EXT_
IN_L
L_OUT
GND
MO
DE_
CTL
_2
ZOOM_BAL
INT_
IN_R
SG
_IN
_L
ZOOM_POSI
SUB_IN_R
MTX
_AM
P_O
UT_
L
VCC
N.C.
AM
P_O
UT_
L
EXT_MIC
N.C.
MTX
_AM
P_I
N_L
REG
_2.5
V
REG_GND
HP_JACK_IN
EXT_MIC_R
MF_B
KEY_AD6
MIC_GND
N.C. (MF_LED)
NS_LED_K
A_4.6V
INT_MIC_R
REG_GND
REG_GND
EXT_MIC_L
MIC_GND
NS_LED_A
INT_MIC_L
SIRCS_SIG
MIC_GND
XF_TALLY_LED
HP_R_OUT
HP_L_OUT
MF_A
MIC_GND
AU_2.8V
TOMA-409 BOARDCN5902
)(PAGE 4-12)
( THROUGHTHE FP-437 FLEXIBLE
(2/6)
LED DRIVE
SWITCH
MIC AMP
IC4401
MIC AMP(MA BLOCK)VA-117 BOARD(3/6)
XX MARK:NO MOUNT
9
G
E
8
F
5
C
3 7 114 132
B
6 10 12
D
16
PB
REC
SIGNAL PATH
SIGNALAUDIO
(4/6)10
(2/6)5
(4/6)11
(6/6)12
(6/6)13
7
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-29 4-30
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
VA-117 (4/6)
For Schematic Diagram• Refer to page 4-85 for printed wiring board.• Refer to page 4-95 for waveforms.
1.5
R8.4
0.9
8.2
7.1
1.1
7.9
15.7 6.8
1.6
1.5
2.9
7.0
2.9
2.6
0.7
7.7
1.1
0.9
1.5
20
8.1
8.0
6.5
0.9
7.7
0.6
0.3
8.5
R6.8P8.6
1.3
1.5
7.0
1.2
2.1
8.0
8.1
0.8
0.8
0.8
8.4
2.3
4.9
3.0
0
1.5
8.5
3.0
0.3
1.6
8.2
8.2
21
8.0
8.1
4.7
1.5
1.5
P7.1
8.6
1.2
6.4
8.2
0.9
4.7
8.1
8.0
0
2.6
8.2
8.2
8.2
2.9
7.7
1.5
2.3
2.9
0 0
R-1.4
7.7
8.2
2.3
R7.2/P8.0
P7.8R7.6
5.1
P3.4R3.1
8.2
P-1.6
8.2
1.6
8.2
4.9
0
5.18.2
2.8
0.9
8.0
7.9
8.0
0.4
R15.0P15.8
1.2
R15
.2P
0
4.7
R4.
6/P
0
P0R2.3
P0R2.8
1.9
P0
P-10.2R-9.5
2.8
R4.2P5.2
-15.9
-1.1
R-25.2/P23.5
15.7
R-25.3/P-23.3
14.5
15.7
13.9
R0.4
P0
P-0.2
R-7.6
R-0
.9/P
0.2
R-9.9/P-10.1
R-7
.6
R15.2/P0
2.8
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
L450622uH
0.5%47k
R4551
2SC4738F-Y/GR(TPL3)Q4514
CXA3282R-T6
IC4501
12345678910111213141516
1718
1920
2122
2324
2526
2728
2930
3132
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
4950
5152
5354
5556
5758
5960
6162
6364
L45194.7uH
A_2.8V
0.5
%18
kR45
15
C45284.7u10V B
2SC4738F-Y/GR(TPL3)Q4519
47kR4524
10kR4507
D_1.9V
22kR4533
REG_1.5V
4700pB
C4508
2SC4738F-Y/GR(TPL3)Q4521
4700
pB
C45
10
10u6.3V
A
C4533
CPH6702-TL-EQ4508
1
2
3 4
5
6
C45304.7u10V B
REG_GND
L45104.7uH
L450422uH
AU_4.75V
100kR4537
DRUM_ERROR
0.5%
R4504470k
BL_CONT
22k
R45
19
680pB
C4509
5%4700
R4544
0.5%15k
R4552
REG_GND
4700
R45
12
CAM_DD_ON
CPH6701-TL-EQ4506
1
2
3 4
5
6
C4527
10V B4.7u
CPH6701-TL-EQ4509
1
2
3 4
5
6
33uHL4501
0.5%4700
R4550
33kR4502
R452847k
CPH6702-TL-EQ4510
1
2
3 4
5
6
D_2.8V
EP_2.8V
100kR4543
XXC4545
0.5%100k
R4508
0.01u
F
C4529
16V
0.5%68k
R4546
BL_REG_UNREG
CPH6102-TL-EQ4501
1234 5 6
4.7u25V
C4546
REG_GND
C45354.7u
C45344.7u
L45114.7uH
BL_REG
22kR4511
10u16V
C4551
100kR4542
0.5%39k
R4535
VTR_UNREG
0R4517
33k
R45
18
4700R4525
0.5%22k
R4501
10u6.3V
A
C4536
L450222uH
2SA1832F-Y/GR(TPL3)Q4504
100kR4532
22u6.3V
A
C4547
22u4VA
C4559
CAP_VS
1SS383(T5RSONY1)D4503
Q4511SI2304DS-T1
T4501
1
2
3
4 5
6
7
8
10u6.3V
A
C4556
0.001uB
C4519
10u6.3V
A
C4553
0.00
1uB
C45
18
470pB
C4515
22u4VA
C4557
REG_GND
0.001uB
C4516
EP_4.75V
47kR4531
4.7uHL4509
C45314.7u
10V B
0.001uB
C4520
RP_4.75V
5%
R45090
0R4510
10u10V
A
C4544
XXR4549
R4530XX
1uHL4522
10k
R45
20
SI2304DS-T1Q4512
0R4554
0.1uC4538
10u6.3V
A
C4541
HN1A01FE-Y/GR(TPLR3)Q4520
6
2
1
3
5
4
0.01uB
C4507
4.7u10V B
C4521
0.5%100k
R4539
8.2k
R45
40
2.2uF
C4555XXD4501
0.5%36k
R4527
0.00
1uB
C45
17
L45174.7uH
4700R4514
2SC4738F-Y/GR(TPL3)Q4517
XXL4512
XXR4553
CPH6702-TL-EQ4503
1
2
3 4
5
6
XXR4516
0.001uB
C4513
XXD4504
D_1.5V
22uHL4503
2200
pB
C45
12
22kR4538
CAP_ERROR
2SB798-T1-DLDKQ4502
0.5%27k
R4526
HN
1C01
FE-Y
/GR
(TP
LR3)
Q45
16
6
2
1
3
5
4
EP_13.3V
C/D_VS_D1.5V XXC4524
CPH6702-TL-EQ4505
1
2
3 4
5
6
15kR4506
2.2uF
C4554
4.7uHL4507
0.1uB
C4543
0R
4513
2SA1832F-Y/GR(TPL3)Q4515
6800R4503
4.7uHL4508
PANEL_-15.3V
22u6.3V
A
C4550
L45154.7uH
VTR_DD_ON
MT_5V
0R
4521
HN1C01FE-Y/GR(TPLR3)Q4507
6
2
1
3
5
4
L450533uH
Q4513RN1104F(TPL3)
PLL_1.5V
10u10VA
C4525
C454822u
6.3VA
R452922k
10u6.3V
A
C4539
22uHL4516
A_4.75V
CAM_-6.5V
0.5%100k
R4534
DRUM_VS
0.5%5.6k
R4536
C45324.7u10V B
HN1A01FE-Y/GR(TPLR3)Q4518
6
2
1
3
5
4
XXR4564
1500
pB
C45
11
AU_2.8V
4700pB
C4501
0.5%220k
R4541
C454910u6.3V
A
1uHL4520
4.7u10V
B
C4523
0R4505
CAM_12V
±
±
±
0.5%220k
R4545
C45224.7u10V
B
1uHL4513
1SS383(T5RSONY1)D4502
L45144.7uH
4.7u10V
B
C4526
R1121N191B-TLIC4505
12
3 45
XXC4540
220p CHC4502
0.1uB
C4505
0.1u BC4503
0.1uB
C4506
0.047uB
C4504
REG_GND
REG_GND
EP_13.3V
EP_4.75V
EP_2.8V
MT_5V
A_4.75V
EP_13.3V
AU_4.75V
AU_2.8V
REG_GND
XXC4514
1
A
VTR_UNREG
VTR_UNREG
CAP_ERROR
DRUM_ERROR
CAP_VS
DRUM_VS
CAP_ERROR
CAP_VS
DRUM_ERROR
DRUM_VS
OU
TPU
T-7
NO
NIN
V_I
NP
UT-
5
BO
OT_
CA
P_L
-2
INV
_IN
PU
T-3
MOS_GATE-4
OUTPUT_GND-4,5,6,7
STANDBY-7
INV
_IN
PU
T-7
OU
TPU
T_M
ON
ITO
R-2
SOFT_START
OUTPUT-3
INV
_IN
PU
T-6
BOOT_CAP_H-6
CO
MP
OUTPUT-4
OU
TPU
T_V
CC
-7
OU
TPU
T-1
RT
OU
TPU
T_V
CC
-4,5
,6
OU
TPU
T_M
ON
ITO
R-5
BO
OT_
CA
P_H
-2
OU
TPU
T_M
ON
ITO
R-3
OUTPUT_GND-1,2,3
BOOT_CAP_H-5
OUTPUT_MONITOR-4
FEED_BACK-3
VREF(1.5V)
NO
NIN
V_I
NP
UT-
6
MO
S_G
ATE-
1N
ON
INV
_IN
PU
T-7
FEED
_BA
CK
-1
BO
OT_
CA
P_H
-7
OUTPUT_VCC-1,2,3
FEED_BACK-5
CT
BOOT_CAP_L-4
OU
TPU
T-2
FEED
_BA
CK
-6
OU
TPU
T_M
ON
ITO
R-6
OUTPUT-6
INV_INPUT-4
FEED
_BA
CK
-2
SCP
BOOT_CAP_L-5
STANDBY-3 BOOT_CAP_H-3
MOS_DUTY
BO
OT_
CA
P_H
-1O
UTP
UT_
MO
NIT
OR
-7
INV
_IN
PU
T-1
BO
OT_
CA
P_L
-7
INV
_IN
PU
T-5
BOOT_CAP_H-4
FEED
_BA
CK
-7
STANDBY
VCC
BOOT_CAP_L-3
BOOT_CAP_L-6
FEED_BACK-4
INV
_IN
PU
T-2
OUTPUT-5
GND
BO
OT_
CA
P_L
-1
OU
TPU
T_M
ON
ITO
R-1
Vout GND VDD
N.C.
CE
IC4501DC-DC CONVERTER
Q4502,4504,4507 MT 5V REG
Q4508,4509,4510 SWITCHING
Q4505,4506,4511,4512 SWITCHING
SWITCHING
DC-DC CONVERTER TRANSFORMER
SWITCHING
EMERGENCY DETECT
Q4514,4515,4516 CAM 12V REG
Q4517,4518CAM -6.5V REG EP 13.3V REG
Q4519,4520-15.3V REG
IC4505D1.9V REG
9
G
E
8 15
F
5 18
J
C
143 7 114 1713
I
2
B
6 10 1612
D
H
XX MARK:NO MOUNT
DC-DC CONVERTER(DD BLOCK)VA-117 BOARD(4/6)
16
Drum servo (speed and phase)
REC/PBREC
Capstan servo (speed and phase)
SIGNAL PATHPB
(2/6)9
14 (5/6)
15 (6/6)
16 (6/6)
10 (3/6)
1 (1/6)
8 (2/6)
4 (2/6)
11 (3/6)
17 (6/6)
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-31 4-32
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
VA-117 (5/6)
For Schematic Diagram• Refer to page 4-85 for printed wiring board.
7.8
8.1
0.1
8.2
8.2
7.6
0.13.1
7.8
7.88.
28.
0
P8.2
8.2 R8.2
R8.2/P0
R3.1
R0/P8.2
P8.2R0.2
8.2
R0/P8.2
8.2
P0R8.2
8.2
P0R8.2
R0
R0.2
8.2
P0.1
P8.2
P8.2
P0
8.2
R0.2
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
P8.2R0.2
F46061.4A/32V
XXR4602
1MR4615
4.7uHL4601
FAST_CHARGE
2SB1122-ST-TDQ4603
1
23
47kR4611
RN2104F(TPL3)Q4606
1
2
3
SHOE_ON
100kR4604
REG_GND
C460422u16V
TA B
F46051.4A/32V
BL_REG_UNREG
1MR4605
BATT_UNREG
SHOE_UNREG
RN1104F(TPL3)Q4604
12
3
C460622u16V
TA B
6800R4609
INIT_CHARGE_ON
0.022uB
C4603
01ZA8.2(TPL3)D4601
123
BATT_SIG
1uB
C4608
SSM3K03FE(TPL3)Q4601
12
3
1kR4608
PRT_HEAD_UNREG
C460522u16VTA B
F46031.4A/32V
100R4614
XXR4603
F46041.4A/32V
2SJ3
05(T
E85L
)Q
4609
12
3
VTR_UNREG
0.1uB
C4602
1kR4601
F46021.4A/32V
1uB
C4607
RN2104F(TPL3)Q4607
1
2
3
XXR4616
0.1uB
C4601
BATT/XEXT
47kR4610
1kR4618
1kR4617
2SJ305(TE85L)Q4608
12
3
100R4612
1MR4613
RN1104F(TPL3)Q4605
12
3
C/D_VS_D1.5V
10R4607
F46011.4A/32VLF4601
XXR4606
1SS383(T5RSONY1)D4602
23
14
TPCS8302(TE12L)Q4610
1
4
23
8
5
67
TPCS8302(TE12L)Q4602
1
4
23
8
5
67
Q4611XX
1
3
4256
6PCN4601
1
2
3
4
5
6
REG_GND
1
A
BATT_SIG
BATT/XEXT
ACV_GND
BATT_GND
BATT_UNREG
ACV_UNREG
SWITCH
SWITCHCHARGE SWITCH
CHARGE SWITCH
Q4605-4609 SWITCH
SWITCHING
(SHOE_GND)
S
BATTERYTERMINAL
DC IN
BT901
9
G
E
8
F
5
C
3 7 1142
B
6 10 12
D
XX MARK:NO MOUNT
CHARGE(FU BLOCK)VA-117 BOARD(5/6)
16
(6/6)18
14 (4/6)
(6/6)19
20 (6/6)
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-33 4-34
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
VA-117 (6/6)
For Schematic Diagram• Refer to page 4-85 for printed wiring board.• Refer to page 4-94 for waveforms.
4
3
21
10
9
8
5
6
7
2.6
2.6
2.5
2.80
4.7
0.1
0
2.2
4.7
4.7
1.6
1.8
1.3
1.3
4.7
4.7
0.5
2.4
1.0
2.1
2.0
0.3
0.1
2.6
R0/P2.3
0
2.6
1.7
-0.8
-0.8
00
-0.8
2.6
2.8
0
0
4.7
NO MARK:REC/PB MODE
C41070.01u
B
C41051u B
C41180.01u B
C41121uB
C41061uB
C41040.22u
B
C41030.033u
B
R410722k
± 0.5%
C41141uB
C412310u 6.3V A
C4124XX
C411110u
6.3V
C41130.01u
B C41160.1uB
L410210uH
FB41010uH
L410110uH
AN2225NFHQBAIC4101
1 2 3 4 5 6 7 8 9 10 11 12
13
14
15
16
17
18
19
20
21
22
23
24
252627282930313233343536
37
38
39
40
41
42
43
44
45
46
47
48
0.01uB
C4119
10kR4110
0.01uB
C4115
2SC4738F-Y/GR(TPL3)Q4101
4700R4102
100R4103
0.01uB
C4101 220kR4104
4700R4101
R41091k
R41081k
BC41102.2u
B2.2uC4108
B2.2uC4109
B2.2u
C4121
B2.2u
C4117
R41061k
Q4102RN2104F(TPL3)
R41051k
C4102XX
HN1C01FE-Y/GR(TPLR3)Q4103
6
2
1
3
5
4
C4V220u
C4120
4V220uC4122
22pCH
C4125
2200R4111
33R4112
33R4113
33R4114
33R4115
33R4116
33R4117
1kR4118
1kR4119
1kR4120
1kR4121
HP_JACK_IN
REG_GND
XMIC_MONO
EXT_MIC_JACK
AU_LINE_I/O_R
INIT_CHARGE_ON
SIRCS_SIG
EVF_R
BATT/XEXT
EVF_G/BW_Y
MF_B
100PCN4002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
PANEL_XHD
EVF_B
MF_A
XVSP_SCK
XF_TALLY_LED
XCS_AU1
G
ZOOM_MIC_CONT
BEEP_IN
AU_LINE_I/O_L
XAUDIO_IN
VSP_SO
FAST_CHARGE
KEY_AD6
XCS_EVF
PANEL_XVD
IR_ON
BATT_SIG
SHOE_ON
MF_LED
VCO
SIRCS_PWM
PRT_HEAD_UNREG
01ZA
8.2(
TPL3
)D
4003
0R4001
20PCN4001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0.1uB
C4003
SHOE/MT_UNREG
0.1uB
C4001
0R4005
REG_GND
0R4003
01ZA
8.2(
TPL3
)D
4005
0R4002
0.1uB
C4002
01ZA
8.2(
TPL3
)D
4001
01ZA
8.2(
TPL3
)D
4004
UD
ZSTE
-178
.2B
D40
06
0R4004
SHOE_MIC_L
20p
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
REG_GND
CAM_DD_ON
VTR_DD_ON
XRST_VTR
VD_SO
VD_SCK
1
A
BATT_UNREG
REG_1.5V
CAM_12V
RP_4.75V
VTR_UNREG
PLL_1.5V
MT_5V
CAM_-6.5V
D_1.9V
D_1.5V
D_2.8V
A_2.8V
EP_13.3V
A_4.75V
CAP_VS
DRUM_VS
DRUM_ERROR
CAP_ERROR
REC_OUT_R
IC4301_L
REC_OUT_L
IC4301_R
PB_IN_R
PB_IN_L
VD
_SO
VD
_SC
K
XC
S_I
C41
01
IC41
01_C
_OU
T
IC41
01_Y
_OU
T
Y_O
UT
DR_C_OUT
AC
C_C
ON
T
AG
C_C
ON
T
S_Y
_I/O
VID
EO_I
/O
DR
_C_O
UT
DR_Y_OUT
DR
_Y_O
UT
DR
_V_O
UT
DR_V_OUT
SHOE_CONT_AD
S_Y_I/O
XCS_IC4101
HS_TXD
DRUM_ERROR
HOTSHOE_ID2
ACC_CONT
DRUM_VS
HS_SCK
HS_RXD
VD_SO
AGC_CONT
VIDEO_I/O
IC4101_Y_OUT
HOTSHOE_ID1
CAP_ERROR
VTR_DD_ON
IC4101_C_OUT
VD_SCK
EXT_STROBO
S_C_I/O
CAP_VS
C_OUT
Y_OUT
HS_HDS
CAM_DD_ON
LANC_SIG
HOTSHOE_ID2
HS_SCK
HOTSHOE_ID1
HS_HDS
SHOE_CONT_AD
LANC_SIG
EXT_STROBO
HS_RXD
HS_TXD
C_O
UT
S_C
_I/O
DRUM_VS
DRUM_ERROR
CAP_VS
CAP_ERROR
CAM_DD_ON
VTR_DD_ON
VD_SO
VD_SCK
C_G
CA
_CO
NT
AG
C_V
OU
T
C_I
N2
MA
IN_V
CC
C_I
N3
D_G
ND
C_I
N4
D_V
CC
SI
XS
CK
XC
S
C_G
ND
SDC
DRV_C_OUT
C_VCC
Y_GND
Y_INV
DRV_Y_OUT
Y_VCC
V_GND
V_INV
DRV_V_OUT
V_VCC
IR_V_OUT
MM
_TC
2
4FS
C_O
UT
MM
_TC
3
XTA
L
PLL
_VC
C
EXTA
L
AP
C_F
IL
BG
T_O
UT
PLL
_GN
D
INP
UT_
C_O
UT
VR
EF
INP
UT_
Y_O
UT
IR
MAIN_GND1
Y_IN1
MAIN_GND2
SYNC_SEP_TC
Y_IN2
CLAMP_TC1
Y_IN3
CLAMP_TC2
Y_IN4
Y_GCA_CONT
C_IN1
VIDEO IN/OUT,AGC
IC4101
BATT_SIG
IC4101_Y_OUT
REG_GND
A_4.75V
EVF_G/BW_Y
PB_IN_R
CAM_12V
MT_5V
CAM_-6.5V
AGC_CONT
CAP_VS
HP_JACK_IN
SDC_IN
XCS_EVF
XRST_VTR
HS_TXD
CAP_VS
DRUM_VS
REG_GND
REC_OUT_L
DRUM_VS
ZOOM_MIC_CONT
VD_SCK
HOTSHOE_ID1
REG_GND
VIDEO_I/O
BATT_UNREG
VD_SO
D_1.5V
KEY_AD6
REG_GND
VTR_UNREG
LANC_SIG
IC2101_OUT
VTR_DD_ON
MT_GND
EXT_MIC_JACK
SIRCS_PWM
XF_TALLY_LED
REG_GND
PLL_1.5V
AU_LINE_I/O_R
PB_IN_L
D_2.8V
IC1601_1.5V
MF_LED
D_1.9V
CAM_DD_ON
VSP_SO
IC4101_C_OUT
IC4301_R
AU_LINE_I/O_L
XCS_AU1
SHOE_CONT_AD
REC_OUT_R
RP_4.75V
XVSP_SCK
BATT_XEXT
PANEL_XHD
DRUM_ERROR
EP_13.3V
HOTSHOE_ID2
PANEL_XVD
MF_B
MT_5V
MT_GND
ACC_CONT
MF_A
HS_SCK
IC4301_L
BEEP_IN
REG_GND
EVF_R
D_2.8V
HS_RXD
IR_ON
SIRCS_SIG
XVIDEO_IN
HS_HDS
XAUDIO_IN
A_2.8V
FAST_CHARGE
IC2101_OUT
VCO
EVF_B
SHOE_ON
D_1.5V
XCS_IC4101
A_2.8V
D_2.8V
S_C_I/O
A_4.75V
EXT_STROBO
XMIC_MONO
G
REG_GND
CAP_ERROR
INIT_CHARGE_ON
IC1601_1.5V
S_Y_I/O
TXD
SHOE_UNREG_GND
SHOE_MT_GND
SHOE_MIC_L
SHOE_ID1
LANC_SIG
SHOE_UNREG
SHOE_MT_GND
PRT_HEAD_UNREG
SHOE_CONT_AD
SCK
RXD
PRT_HEAD_UNREG
SHOE_MIC_GND
SHOE_ID2
HDS
SHOE_UNREG_GND
SHOE_UNREG_GND
SHOE_UNREG
STBY_ON
SHOE_MIC_GND
SHOE_UNREG
SHOE_ID2
PRT_HEAD_UNREG
STBY_ON
SHOE_UNREG
PRT_HEAD_UNREG
RXD
SHOE_CONT_AD
TXD
SHOE_UNREG_GND
HDS
SHOE_UNREG_GND
SHOE_MIC_L
SHOE_MT_GND
SCK
RXD
STBY_ON
TXD
HDS
SHOE_MT_GND
SHOE_ID1
LANC_SIG
SCK
LANC_SIG
SHOE_CONT_AD
SHOE_UNREG
SHOE_UNREG_GND
SHOE_MT_GND
PRT_HEAD_UNREG
SHOE_MIC_GND
SHOE_ID2
SHOE_MIC_L
SHOE_ID1
SHOE_UNREG_GND
BUFFER
SWITCH
SWITCH
FP-436FLEXIBLE
INTELLIGENTACCESSORYSHOE
VIDEO I/O(TA BLOCK)XX MARK:NO MOUNT
VA-117 BOARD(6/6)
9
G
K
E
8 15
F
5
J
C
143 7 114 17
M
13
I
2
B
6 10 1612
L
D
H
16
REC
SIGNAL PATHREC/PB
Drum servo (speed and phase)
PB
SIGNAL PATH
REC
VIDEO SIGNAL
PB
Y/CHROMA SIGNALAUDIO
YCHROMA
Capstan servo (speed and phase)
TOVC-281 BOARD(16/16)CN1007
(PAGE 4-67)
18
16 (4/6)
19 (5/6)
18 (5/6)
15 (4/6)
3 (2/6)
17 (4/6)
6 (2/6)
(3/6)12
2 (1/6)
13 (3/6)
20 (5/6)
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-35 4-36FP-100/FP-228/FP-102
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
27P
1LM_LOAD
TO VC-281 BOARD (13/16) CN1010 (PAGE 4-62 of LEVEL3)
2LM_LOAD
3LM_UNLOAD
4LM_UNLOAD
5DEW+
6DEW-
7MODE A
8MODE B
9MODE C
10SW_COM/SW_GNDS903
D901
4PCN901
S901
1
A
MIC
/REC
_SW
_GN
D
TAP
E_EN
D
XR
EC_P
RO
OF
HA
LL_G
ND
DEW
+
CH
IME_
VD
D
TREE
L-
SW
_CO
M/S
W_G
ND
LM_U
NLO
AD
TOP
/EN
D_G
ND
DEW
-
XC
CD
OW
N_S
W
TAP
E_LE
D_A
XM
OD
E_S
W_A
XM
OD
E_S
W_B
LM_U
NLO
AD
LM_L
OA
D
SR
EEL-
CH
IME_
SD
A
HA
LL_V
CC
SR
EEL+
TAP
E_TO
P
TAP
E_LE
D_K
TREE
L+
CH
IME_
SC
K
LM_L
OA
D
XM
OD
E_S
W_C
(CC DOWN)
(TAPE LED)
M M903LOADING MOTOR
S902 MODESWITCH
FLEXIBLE
FP-100
Vcc -
+ G
-Vcc
G+
H902T REELSENSOR
H901S REELSENSOR
Q902TAPE TOPSENSOR
Q901TAPE ENDSENSOR
(REC PROOF)
FP-102FLEXIBLE
DEWSENSOR
FP-228FLEXIBLE
B
4
D
C
732 65
16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
Schematic diagram of the VC-281 board are not shown.Pages from 4-37 to 4-68 are not shown.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
LinkLink
4-3. PRINTED WIRING BOARDS
FP-444 FLEXIBLE BOARD
FB-219 BOARD
MA-409 BOARD
VA-117 BOARD (SIDE B)
JK-218 BOARD
VA-117 BOARD (SIDE A)
JK-217 BOARD
CK-108 BOARD (SIDE B)
CK-108 BOARD (SIDE A)
FP-443 FLEXIBLE BOARD
FP-100, FP-228, FP-102 FLEXIBLE BOARDS
CD-366 BOARD
LB-077 BOARD
PD-161 BOARD
FP-444 FLEXIBLE BOARD
FB-219 BOARD
PD-161 BOARD
MA-409 BOARD
VA-117 BOARD (SIDE B)
JK-218 BOARD
VA-117 BOARD (SIDE A)
JK-217 BOARD
CK-108 BOARD (SIDE B)
CK-108 BOARD (SIDE A)
FP-443 FLEXIBLE BOARD
FP-100, FP-228, FP-102 FLEXIBLE BOARDS
LB-077 BOARD
CD-366 BOARD
CIRCUIT BOARDS LOCATION
WAVEFORMSCOMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION FLEXIBLE BOARDS LOCATIONCIRCUIT BOARDS LOCATION
WAVEFORMSCOMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION FLEXIBLE BOARDS LOCATION
4-69
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
(For printed wiring boards)• : Uses unleaded solder.• : Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated)• Through hole is omitted.• Circled numbers refer to waveforms.• There are a few cases that the part printed on diagram
isn’t mounted in this model.• C: panel designation
THIS NOTE IS COMMON FOR WIRING BOARDS(In addition to this, the necessary note is printed in each block)
2 1
3
2 1
3
2 1
3
345
21
123
654
EB
C
31
55
2
46
123
54
4 3
1 212
43
31 2
45
53 4
12
34
21
12
43
46
2
5
31
12
43
• Chip parts.Transistor Diode
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-71 4-72 CD-366/FP-443
CD-366 (CCD IMAGER) PRINTED WIRING BOARD4-3. PRINTED WIRING BOARDS
FP-443 FLEXIBLE BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
EDIT SEARCH –
EDIT SEARCH +
1
6
R201
R202S202
S203
S201(EJECT SW)
1-684-257- 21
FP-443 FLEXIBLE• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-98 for parts location.• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-73 4-74
JK-217 (STEADY SHOT, A/D IN/OUT), JK-218 (DIGITAL IN/OUT) PRINTED WIRING BOARD
JK-217/JK-218
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
IN :TRV24EIN/OUT:TRV25E/
TRV27E
IN :TRV24EIN/OUT:TRV25E/
TRV27E
S VIDEO
AUDIO/VIDEO
12
DV IN/OUT
DV IN
: TRV25E/TRV27E
: TRV24E
12
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-98 for parts location.• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-75 4-76 MA-409/FP-444
MA-409 (MIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCH) PRINTED WIRING BOARD FP-444 FLEXIBLE BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
MIC(PLUG IN POWER)
12
S301
R301 R302
S302
1-684-258- 21
1
16
8
FP-444 FLEXIBLE
FOCUS(INFINITY)
FADER
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-98 for parts location.• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-77 4-78FB-219/PD-161
FB-219 (MANUAL FOCUS SENSOR), PD-161 (RGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHT) PRINTED WIRING BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
12
• : Uses unleaded solder.
For printed wiring boards• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
For printed wiring boards• Refer to page 4-98 for parts location.• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-79 4-80 LB-077/FP-100/FP-228/FP-102
FP-100 (MODE SWITCH), FP-228 (DEW SENSOR), FP-102 (TAPE TOP/END SENSOR, S/T REEL) FLEXIBLE BOARDLB-077 (EVF, EVF BACK LIGHT) PRINTED WIRING BOARD
1-677-085-
1-677-049-
12
11
110
101
127
M
S902MODE SWITCH
DEWSENSOR
M903LOADINGMOTOR
D901(TAPE LED)
S903(CC DOWN)
S901(REC PROOF)
Q902TAPE TOPSENSOR
Q901TAPE ENDSENSOR
H902T REEL
SENSOR
H901S REEL
SENSOR
CN901
FP-102 FLEXIBLE BOARD
FP-100 FLEXIBLE BOARD
FP-228FLEXIBLE BOARD
12
• : Uses unleaded solder. (LB-077 board)
For printed wiring boards• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-81 4-82CK-108
CK-108 (SWITCH, CONNECTOR) PRINTED WIRING BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
STOP REW PLAY FFPAUSE
12
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-99 for parts location.• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-83 CK-1084-84
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
(SECONDARY)
12
• : Uses unleaded solder.
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-85 4-86VA-117
VA-117 (RGB DRIVE, TG, AUDIO, MIC AMP, DC-DC CONVERTER, CHARGE, VIDEO I/O) PRINTED WIRING BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-99 for parts location.• This board is six-layer print board. However, the
patterns of layers two and five have not been includedin the diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-87 4-88 VA-117
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
• : Uses unleaded solder.
Printed wiring board of the VC-281board are not shown.Pages from 4-89 to 4-92 are not shown.
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-93 4-94CD-366/PD-161/VA-117
4-4. WAVEFORMS
CD-366 BOARD CAMERA REC
2 IC5101 3,4
1 IC5101 1,2
7.8 Vp-p
7.8 Vp-p
4 IC5101 q;
6.2 Vp-p
30.3 nsec
30.3 nsec
30.3 nsec
650mVp-p
3 IC5101 8,IC5102 qa
4.7Vp-p
5 IC5101 qa,qs
6 IC5102 qd,qf
4.8 Vp-p
43.3 µsec
43.3 µsec
43.3 µsec
PD-161 BOARD REC/PB
2 IC5501 ws
3 IC5501 wf
1 IC5501 w;
3.8Vp-p
H
9 IC5502 wh
2.9 Vp-p
85 nsec
3.8Vp-p
3.8Vp-p
H
H
q; IC5651 2
3.1 Vp-p
6 IC5501 rh
H
5 IC5501 rj
H
4 IC5501 rk
480 mVp-p
450 mVp-p
500 mVp-p
H
7 IC5502 1
2.8Vp-p
H
8 IC5502 rk
2.8Vp-p
V
39 µsec
VA-117 BOARD
1 IC4101 7 CAMERA REC S JACK IN
2 IC4101 qf CAMERA REC S JACK IN
H
qd IC4201 wf REC/PB
7.0 Vp-p0.4Vp-p
H
H1.4 Vp-p
H
1.8 Vp-p
3 IC4101 qk CAMERA REC/PB S JACK IN
4 IC4101 ws CAMERA REC/PB AV JACK IN
2.2Vp-p
H
5 IC4101 ef LINE REC(S-VIDEO)
1.0 Vp-p
H
6 IC4101 eh LINE REC(S-VIDEO)
0.8 Vp-p
H
7 IC4101 el LINE REC (S-VIDEO)
H
420 mVp-p
H
0.5Vp-p
8 IC4101 rs LINE REC (AV VIDEO)
9 IC4101 rh CAMERA REC/PB AV JACK or S JACK IN
450 mVp-pH
H
q; IC4101 rk LINE REC (S-VIDEO)
1.3 Vp-p
qa IC4201 w; REC/PB
6.2Vp-p
H
qs IC4201 ws REC/PB
7.0 Vp-p
H
qf IC4201 rh REC/PB
350 mVp-p
H
qh IC4201 rk REC/PB
350 mVp-p
H
qg IC4201 rj REC/PB
350mVp-p
H
qj IC4202 1 REC/PB
2.8Vp-p
H
qk IC4202 rk REC/PB
2.8Vp-p
V
PD-161 BOARD VA-117 BOARD SIDE A VA-117 BOARD SIDE BCD-366 BOARDCD-366 BOARD PD-161 BOARD VA-117 BOARD SIDE A VA-117 BOARD SIDE B
4-95
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
VA-117
VA-117 BOARD
w; IC4501 tk REC/PB
0.8 Vp-p
2.3 µsec
wa IC4501 yf REC/PB
0.8 Vp-p
2.3 µsec
ql IC4202 wh REC/PB
2.1 Vp-p
92 nsec
VA-117 BOARD SIDE A VA-117 BOARD SIDE BVA-117 BOARD SIDE A VA-117 BOARD SIDE B
Waveforms of the VC-281 board are not shown.Pages from 4-96 to 4-97 are not shown.
4-98
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
4-5. MOUNTED PARTS LOCATION no mark : side A* mark : side B
JK-217 BOARD
* C5301 A-3* C5302 A-3
CN5305 B-3
* D5301 D-1* D5302 B-2
* FB5301 D-1* FB5302 B-3* FB5303 A-2* FB5304 A-2* FB5305 B-2* FB5307 B-3* FB5308 C-1* FB5309 B-1* FB5310 B-2
J5301 D-1J5302 B-2
* R5301 C-1* R5302 B-1* R5303 B-2* R5304 B-2* R5305 B-3
SE5301 B-3SE5302 A-3
* VD5301 B-1* VD5302 D-1* VD5303 B-2* VD5304 C-1* VD5305 B-2* VD5306 B-1
CD-366 BOARD MA-409 BOARD
C5901 C-2C5902 B-1
* CN5901 B-2* CN5902 B-1* CN5903 A-1
D5901 A-1D5902 A-1D5903 B-1
* D5904 A-1* D5905 A-1
* FB5901 B-2* FB5902 B-2
FB5903 B-2FB5904 B-2
IC5901 B-1
J5901 C-2J5902 C-3
R5901 B-1
VD5901 B-3VD5902 B-2VD5903 B-2VD5904 B-2
PD-161 BOARD
C5501 C-3C5503 C-3C5504 B-2C5505 C-2C5506 C-2C5507 C-2C5508 B-2C5509 C-1C5510 C-2C5511 B-3C5512 B-3C5513 C-2C5514 C-2C5515 B-3C5516 B-3C5517 C-3C5518 C-3C5519 C-3C5520 C-2C5521 D-1C5522 C-3C5523 A-2C5524 B-1C5527 C-3C5528 A-3C5530 A-1C5531 A-1C5532 C-1C5603 C-6C5604 B-5C5605 B-5C5606 B-6C5607 D-6
CN5501 A-2CN5601 A-5CN5651 D-1CN5652 B-1CN5653 C-2CN5654 A-4
D5502 B-3D5503 A-3D5504 B-1D5601 B-5D5602 A-5D5603 C-5D5604 D-5
FB5501 C-1FB5502 C-1FB5503 C-1
IC5501 C-3IC5502 B-2IC5601 C-5IC5602 B-5IC5651 C-4
L5501 D-3L5502 C-1L5503 B-2L5601 C-5
CD-366/JK-217/MA-409/PD-161
4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
* C5101 C-1* C5102 B-2* C5103 B-2* C5104 B-1* C5105 B-1* C5106 A-2* C5107 B-2* C5108 B-1* C5109 B-2
C5110 A-2* C5111 A-1
C5112 A-2* C5113 A-2
C5114 A-1* C5115 B-2* C5116 B-1
* CN5101 A-1* CN5102 A-2
* FB5101 A-1* FB5102 A-1* FB5103 A-1
IC5101 B-1* IC5102 B-1
L5101 A-2L5102 A-1
* Q5101 A-2
* R5101 C-1* R5102 A-2
Q5502 B-1Q5503 B-1Q5504 B-1Q5505 B-2Q5601 C-5Q5603 B-5Q5604 C-6Q5605 C-6
R5501 C-2R5502 C-2R5503 C-2R5505 C-2R5506 B-3R5507 B-3R5508 B-3R5509 B-3R5510 B-3R5511 B-3R5512 B-3R5513 B-3R5514 A-2R5515 A-2R5516 C-2R5517 B-1R5518 B-1R5519 B-1R5520 A-2R5521 B-1R5523 C-2R5525 A-2R5528 B-1R5529 B-1R5530 B-1R5531 C-2R5532 B-2R5533 C-1R5534 B-2R5540 B-1R5541 B-1R5552 B-1R5591 B-1R5601 C-6R5602 B-5R5603 B-5R5604 C-6R5605 B-5R5606 B-5R5607 B-5R5608 C-5R5609 D-5R5612 C-5R5613 B-5R5614 B-5R5651 C-4R5652 C-4
RB5501 C-3RB5502 A-1RB5503 B-1
T5601 B-6
VD5651 C-4
4-99E
DCR-TRV24E/TRV25E/TRV27E
COVERCOVER
R4427 B-1R4428 B-1R4429 B-1
* R4430 A-1* R4431 A-1* R4501 D-5* R4502 D-5* R4503 D-5* R4504 D-5* R4505 D-5* R4506 E-5* R4507 D-5* R4508 D-5* R4509 E-5* R4510 D-5* R4511 E-5* R4512 D-5* R4513 E-5* R4514 E-5* R4515 C-5* R4516 E-5* R4517 E-5* R4518 D-5* R4519 D-5* R4520 D-5* R4521 D-5* R4524 B-6* R4525 B-5* R4526 B-5* R4527 B-5
R4528 E-5R4529 E-5R4530 E-6R4531 D-5R4532 E-5R4533 D-5R4534 E-5R4535 E-5R4536 E-5R4537 D-5R4538 D-5R4539 D-5R4540 D-5R4541 D-5R4542 E-5R4543 D-5R4544 D-5R4545 D-5R4546 D-5
* R4549 E-5R4550 D-5R4551 D-5R4552 D-5
* R4553 E-5* R4554 B-5* R4564 D-5
R4601 A-6R4602 B-6R4603 B-6
* R4604 B-6* R4605 B-6* R4606 A-6* R4607 B-6* R4608 A-6* R4609 A-6* R4610 E-2* R4611 E-2* R4612 E-3* R4613 E-3* R4614 E-3* R4615 E-3* R4616 E-3* R4617 E-3* R4618 E-3
T4501 D-6
* R4109 B-3* R4110 B-3* R4111 C-3* R4112 C-4* R4113 C-4* R4114 C-4* R4115 C-4* R4116 C-4* R4117 C-4* R4118 C-2* R4119 C-2* R4120 C-2* R4121 C-3* R4201 E-2* R4202 E-3* R4203 D-3* R4204 D-2* R4205 D-3* R4206 D-3* R4207 D-3* R4208 D-3
R4209 D-3R4210 D-3
* R4211 D-3* R4212 D-2* R4213 D-2* R4214 D-3* R4215 D-3* R4216 D-3* R4217 D-3* R4218 D-3* R4219 D-2* R4220 D-2
R4221 D-4R4222 D-4R4223 D-4R4224 D-4R4301 D-4R4302 B-3R4303 D-4R4304 C-3R4305 D-3R4306 B-3R4307 B-3R4308 B-3R4309 B-3R4310 C-3R4311 C-3R4316 C-3R4317 C-3R4318 D-3R4319 D-3R4401 B-1R4402 B-1R4403 B-1R4404 B-1R4405 B-1R4406 B-1R4407 A-1
* R4408 B-2* R4409 A-2
R4410 A-2R4411 B-2R4412 B-2R4413 A-2
* R4414 B-2R4415 B-2R4416 A-2R4417 A-2R4418 B-2R4419 A-2R4420 B-2R4421 A-2
* R4422 B-2* R4423 B-2
R4424 B-2R4425 B-2R4426 B-1
VA-117 BOARD
C4403 B-1C4404 A-1C4405 B-1
* C4406 B-1C4407 B-1C4408 B-1C4409 B-1C4410 A-1
* C4411 B-1C4412 A-1C4413 B-1C4414 B-1C4415 A-1C4416 A-1C4417 B-2C4418 B-1C4419 A-2C4420 B-2
* C4421 A-2* C4422 B-2* C4423 B-2
C4424 A-2C4425 A-2C4426 B-2C4427 B-2C4428 B-2C4429 A-2C4430 A-2C4431 B-2
* C4432 B-2C4433 B-2
* C4434 B-2C4435 B-1C4436 B-1C4437 B-1C4438 B-1
* C4501 D-5* C4502 D-5* C4503 D-5* C4504 D-5* C4505 D-5* C4506 D-5* C4507 E-5* C4508 D-5* C4509 E-5* C4510 D-5* C4511 E-5* C4512 D-5* C4513 E-5* C4514 D-5* C4515 D-5* C4516 E-5* C4517 D-6* C4518 D-6* C4519 D-6* C4520 D-6* C4521 C-6* C4522 D-6* C4523 C-6* C4524 A-5* C4525 A-6* C4526 C-6* C4527 D-7* C4528 D-6
C4529 E-5* C4530 D-7* C4531 D-6* C4532 D-6* C4533 B-5
C4534 E-6C4535 E-6
* C4536 B-5C4538 E-5
* C4539 B-5* C4540 C-5* C4541 B-5
C4543 D-5* C4544 C-6
* C4545 C-6C4546 D-5C4547 B-5C4548 B-5C4549 A-5C4550 B-5C4551 D-5
* C4553 C-5C4554 D-5C4555 D-5
* C4556 B-5* C4557 C-5* C4559 B-5
C4601 A-6C4602 B-6
* C4603 B-6C4604 C-6
* C4605 B-6* C4606 B-6* C4607 E-3* C4608 E-3
CN4001 E-3* CN4002 A-3* CN4003 B-1
CN4004 B-4CN4201 E-4CN4601 B-6
D4001 D-2D4003 D-2D4004 D-3D4005 D-3D4006 D-2
* D4201 D-3* D4401 A-1
D4501 E-6D4502 E-6D4503 E-6
* D4504 C-6D4601 A-6D4602 A-6
F4601 B-6F4602 B-6F4603 B-6F4604 B-6F4605 B-6F4606 B-6
* FB4101 B-3* FB4201 E-4* FB4202 D-4
FB4301 C-4
* IC4101 C-3* IC4201 D-3* IC4202 D-4
IC4301 C-3IC4401 B-2
* IC4501 D-5* IC4505 C-5
* L4101 B-3* L4102 C-3* L4201 E-4
L4202 D-4L4301 C-4
* L4401 B-2L4501 D-7L4502 D-6L4503 C-6L4504 D-7L4505 D-6L4506 D-6
* L4507 B-5* L4508 B-5* L4509 B-5
* L4510 B-5* L4511 C-6* L4512 C-6
L4513 B-5L4514 B-5L4515 B-5L4516 B-5L4517 D-5
* L4519 C-5* L4520 C-5* L4522 C-5* L4601 C-6
LF4601 B-6
Q4001 A-1* Q4003 A-1* Q4101 C-4* Q4102 C-4* Q4103 C-4
Q4301 D-4Q4302 C-3Q4303 C-3Q4304 C-3Q4305 D-3
* Q4306 B-3* Q4307 B-2* Q4501 D-6* Q4502 A-6* Q4503 D-7* Q4504 B-6* Q4505 D-6* Q4506 D-7* Q4507 B-5* Q4508 C-6* Q4509 D-7* Q4510 D-7* Q4511 D-7* Q4512 D-6
Q4513 E-5Q4514 D-5Q4515 E-5Q4516 E-5Q4517 D-5Q4518 D-5Q4519 D-5Q4520 D-5Q4521 D-5
* Q4601 B-6* Q4602 B-6* Q4603 B-6* Q4604 A-6* Q4605 E-3* Q4606 E-2* Q4607 E-2* Q4608 E-2* Q4609 E-2* Q4610 E-3* Q4611 E-4
R4001 D-2R4002 D-2R4003 D-3R4004 D-3R4005 D-3R4009 A-1
* R4010 A-1R4011 B-1R4012 B-1R4013 A-1
* R4101 C-4* R4102 C-4* R4103 C-4* R4104 C-4* R4105 C-4* R4106 C-4* R4107 C-4* R4108 B-4
C4001 D-2* C4002 E-3
C4003 E-3* C4101 C-4* C4102 C-4* C4103 C-4* C4104 C-4* C4105 C-4* C4106 C-4* C4107 B-4* C4108 C-4* C4109 C-4* C4110 C-4* C4111 B-3* C4112 B-4* C4113 B-3* C4114 C-3* C4115 B-3* C4116 B-3* C4117 C-3* C4118 B-3* C4119 B-3* C4120 C-3* C4121 C-3* C4122 C-3* C4123 C-3* C4124 C-3* C4125 C-3* C4201 E-4* C4202 D-3* C4203 E-2
C4204 D-3C4205 D-3C4206 D-3
* C4207 D-3* C4208 E-4
C4209 D-3C4210 D-3
* C4211 E-4* C4212 D-3* C4213 D-2* C4214 D-3* C4215 D-2* C4216 D-2* C4217 D-3* C4218 D-3* C4219 D-3* C4223 E-4
C4301 C-4C4302 C-4C4303 C-4C4304 C-4C4305 B-4C4306 C-4C4307 C-4C4308 C-4C4309 C-4C4310 C-4C4311 D-4C4312 C-3C4313 C-3C4314 C-3C4315 B-3C4316 D-3C4317 B-3C4318 C-3
* C4319 B-2C4320 B-3C4321 B-3C4322 D-4C4323 C-3C4324 C-3C4325 B-3C4326 B-3
* C4327 B-2* C4328 B-3
C4401 A-1C4402 B-1
CK-108/VA-117
CK-108 BOARD
* BT5201 C-3
C5201 B-5C5202 B-5
* C5203 A-2
* CN5201 C-7* CN5202 A-5* CN5203 A-2
CN5204 B-2* CN5205 B-4* CN5207 C-8
* D5201 A-7* D5203 B-7* D5204 B-7* D5205 A-4* D5206 C-8
D5207 B-5D5208 C-5
R5201 A-5* R5206 B-7* R5207 B-7* R5208 B-7
R5209 A-5* R5210 B-7* R5211 B-7* R5212 B-7
R5213 A-5* R5214 B-7* R5215 B-7* R5216 B-7
R5217 A-6* R5218 B-7* R5219 B-7
R5220 A-7* R5221 C-7* R5222 B-7
R5223 A-7* R5224 C-7* R5225 C-7* R5226 C-8* R5227 A-2* R5228 A-2
S5201 A-4S5202 A-5S5203 B-5S5204 A-6S5205 A-7S5206 A-8S5207 C-1
no mark : side A* mark : side B
4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
Mounted parts location of the VC-281 board is not shown.Pages from 4-100 to 4-101 are not shown.
5-1
DCR-TRV24E/TRV25E/TRV27E
SECTION 5ADJUSTMENTS
COVERCOVER
5-2
DCR-TRV24E/TRV25E/TRV27E
Replaced parts
Block replacement Parts replacement
z z
z
z
z z
z z z
z z z
z z z
z z z
z
z
z
z z
z
z z
z z z
z z
z
z z
z
z
z z z
z z z
z
z z
z z
z z
z z
z z z z
z z z z
z z z z
Len
s de
vice
Mec
hani
sm d
eck
No
teL
CD
blo
ckL
CD
901
(LC
D p
anel
)
LC
D b
lock
ND
901
(Flu
ores
cent
tube
)
EV
F bl
ock
LC
D90
3 (L
CD
pan
el)
Mec
hani
sm d
eck
M90
1 (D
rum
ass
y) N
ote
Mec
hani
sm d
eck
M90
2 (C
apst
an m
otor
)
JK-2
17 b
oard
SE53
01/5
302
(YA
W/P
ITC
H s
enso
r)
PD-1
61 b
oard
IC55
01 (
RG
B d
rive
r (L
CD
))
PD-1
61 b
oard
IC55
02 (
Tim
ing
gene
rato
r (L
CD
))
LB
-077
boa
rdIC
6101
,D61
02 (
Bac
k lig
ht (
EV
F))
VA
-117
boa
rdIC
4201
(R
GB
dri
ver
(EV
F))
VA
-117
boa
rdIC
4202
(T
imin
g ge
nera
tor
(EV
F))
VA
-117
boa
rdIC
4101
(V
ideo
IN
/OU
T)
CD
-366
boa
rdIC
5101
(C
CD
imag
er)
CD
-366
boa
rdIC
5102
(S/
H)
VC
-281
boa
rdIC
1501
, X15
01 (
Tim
ing
gene
rato
r)
VC
-281
boa
rdIC
1502
(A
/D c
onv.
)
VC
-281
boa
rdIC
2101
(D
V s
igna
l pro
cess
)
VC
-281
boa
rdIC
1901
(E
Q, A
/D c
onv.
, PL
L)
VC
-281
boa
rdIC
1902
(R
EC
/PB
AM
P)
VC
-281
boa
rdIC
1801
(E
VR
)
1. Adjusting items when replacing main parts and boards.• Adjusting items when replacing main partsWhen replacing main parts, adjust the items indicated by z in the following table.Note: When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to “00”. (Refer to “Record of Use
check” of “5-4. SERVICE MODE”)
Adjustment
Section
Initialization of8, A, B,C, D,E, F, 1B, 1E, 1Fpage data
Camera
Color EVF
LCD
MechanismSystem control
Video
Servo, RF
Adjustment
Initialization of A, D page dataInitialization of B, 1B page dataInitialization of 8, C page dataInitialization of E, F, 1E, 1F page data54MHz origin oscillation adj.HALL adj.MR adj.Flange back adj.MAX GAIN adj.Color reproduction adj.AWB & LV standard data inputAuto white balance adj.Mechanical shutter adj.Black defective CCD adj.Steady shot checkVCO adj.RGB AMP adj.Contrast adj.White balance adj.VCO adj.RGB AMP adj.Contrast adj.COM AMP adj.V COM adj.White balance adj.Tape path adj.Serial No. inputChroma BPF fo adj.S VIDEO OUT Y level adj.S VIDEO OUT chroma level adj.CAP FG duty adj.PLL fo & LPF fo adj.Switching position adj.AGC center level adj.APC & AEQ adj.PLL fo & LPF fo fine adj.
Table. 5-1-1 (1).
5-3
DCR-TRV24E/TRV25E/TRV27E
Board replacementEEPROM
replacement
z z
z z
z z
z z
z z
z z z
z z z
z z z z
z z z z
z z z
z z z z
z z z z
z z z
z z z
z z z z
z z z
z z z
z z z
z z z z
z z z
z z z
z z z
z z z
z z z
z z z
z z
z z z
z z z
z z z
z z z
z z z
z z z
z z z
z z z
CD
-366
boa
rd(C
OM
PLE
TE
)
JK-2
17 b
oard
(CO
MPL
ET
E)
LB
-077
boa
rd(C
OM
PLE
TE
)
PD-1
61 b
oard
(CO
MPL
ET
E)
VA
-117
boa
rd(C
OM
PLE
TE
)
VC
-281
boa
rd(C
OM
PLE
TE
)
VC
-281
boa
rdIC
2502
(E
EPR
OM
)
VC
-281
boa
rdIC
2901
(E
EPR
OM
)
VC
-281
boa
rdIC
3002
(Fl
ash
mem
ory)
Supp
ortin
g
Adjustment
Section
Initialization of8, A, B,C, D,E, F, 1B, 1E, 1Fpage data
Camera
Color EVF
LCD
MechanismSystem control
Video
Servo, RF
Adjustment
Initialization of A, D page dataInitialization of B, 1B page dataInitialization of 8, C page dataInitialization of E, F, 1E, 1F page data54MHz origin oscillation adj.HALL adj.MR adj.Flange back adj.MAX GAIN adj.Color reproduction adj.AWB & LV standard data inputAuto white balance adj.Mechanical shutter adj.Black defective CCD adj.Steady shot checkVCO adj.RGB AMP adj.Contrast adj.White balance adj.VCO adj.RGB AMP adj.Contrast adj.COM AMP adj.V COM adj.White balance adj.Tape path adj.Serial No. inputChroma BPF fo adj.S VIDEO OUT Y level adj.S VIDEO OUT chroma level adj.CAP FG duty adj.PLL fo & LPF fo adj.Switching position adj.AGC center level adj.APC & AEQ adj.PLL fo & LPF fo fine adj.
Table. 5-1-1 (2).
• Adjusting items when replacing a board or EEPROMWhen replacing a board or EFPROM, adjust the items indicated by z in the following table.
5-4
DCR-TRV24E/TRV25E/TRV27E
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
Name
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander(RM-95 upgraded) (Note)
Siemens star chart
Clear chart for pattern box
CPC-8 jig
Extension cable (100P, 0.5mm)
Mini pattern box
Camera table
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-388-A
J-6082-352-A
J-6082-353-B
J-6082-384-A
UsageAuto white balance adjustment/checkWhite balanceadjustment/check
White balance check
White balance check
White balance check
For checking the flange back
For adjusting the video sectionFor adjusting the color viewfinderFor adjusting the LCD block
For extension between the VA-117 board (CN4002) andthe VC-281 board (CN1007)
For adjusting the flange back
For adjusting the flange back
5-1. CAMERA SECTION ADJUSTMENT
1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1. List of Service Tools• Oscilloscope • Color monitor • Vectorscope• Regulated power supply • Digital voltmeter
Note: If the micro processor IC in the adjustment remote commander isnot the new micro processor (UPD7503G-C56-12), the pages cannotbe switched. In this case, replace with the new micro processor (8-759-148-35).
Fig. 5-1-1.
J-1 J-2
J-6
J-3
J-7 J-8
J-4 J-5
J-9 J-10
J-11
5-5
DCR-TRV24E/TRV25E/TRV27E
1-1-2. PreparationsNote 1: For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.Note 2: When performing only the adjustments, the lens block and boards
need not be disassembled.Note 3: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
1) Connect the equipment for adjustments according to Fig. 5-1-3.
Note 4: As removing the cabinet (R) assembly (removing CN1005 of theVC-281 board) means removing the lithium 3V power supply(BT5201 on the CK-108 board), data such as date, time, user-setmenus will be lost. After completing adjustments, reset these data.But the self-diagnosis data and the data on history of use (totaldrum rotation time etc.) will be kept even if the lithium 3V powersupply is removed. (Refer to “5-4.Service Mode” for the self-diagnosis data and the data on history of use.)
Note 5: Setting the “Forced Camera Power ON” Mode1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 01, and press the PAUSE
button.The above procedure will enable the camera power to be turnedon with the control switch block (PS-CX2670) removed. Aftercompleting adjustments, be sure to exit the “Forced Camera PowerON Mode”.
Note 6: Exiting the “Forced Camera Power ON” Mode1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 00, and press the PAUSE
button.3) Select page: 0, address: 01, and set data: 00.
Fig. 5-1-2.
Front of the lens
Pattern box
1.5 m
5-6
DCR-TRV24E/TRV25E/TRV27E
Fig. 5-1-3.
CN1009
CN1010
CN1501CN1006
CN1301
CN5902
CN1901
VIDEO(Yellow)
AUDIO (L)(White)
AUDIO (R)(Red)
CN1008
CN1002
VC-281 board
Lens block
LANC jack
AUDIO/VIDEO jack
Front panel block
MA-406 boardVA-117 board
Battery terminal
Cabinet (R)
CK-108 board
EVF block
Extension cable (100P)J-6082-352-A
CN1005
DC IN jack
CN1007
CN4002
CN1001
CN1011
CN4004
CN4001
CN5202
CN5201
CN5207
CN5203
CN5205
CN4201
CN4003
CN4601
Terminated at 75 Ω
Vector scope Color monitor
AC power adaptor
AC-L10 orAC-VQ800 etc.
Must be connectedwhen performingthe video or EVF orLCD system adjustment.
Need not be connected
Need not be connected
Must be connectedMust be connected when
performing the LCD system adjustment.
Must be connected when performing the EVF systemadjustment.
Adjustmentremote commander
CPC-8 jig(J-6082-388-A)
5-7
DCR-TRV24E/TRV25E/TRV27E
2. Order of AdjustmentsBasically carry out adjustments in the order given.
Fig. 5-1-4.
3. Subjects1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjustthe picture frame as shown in Fig. 5-1-4. (Color reproductionadjustment frame)
2) Clear chart (Color reproduction adjustment frame)Remove the color bar chart from the pattern box and insert aclear chart in its place. (Do not perform zoom operations duringthis time.)
3) Flange back adjustment chartMake the chart shown in Fig. 5-1-5 using A0 size (1189mm ×841mm) black and white vellum paper.
H
A=B
C=D
A B B
C D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B A
Difference in level
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
Color bar chart (Color reproduction adjustment frame )
Fig. a(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction toobtain the output waveform shown in Fig. aand the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
Fig. 5-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges ofthe black and white paper joined together are not rough.
1-1-3. Precaution1. Setting the SwitchUnless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (PS-CX2670 block) ..................... CAMERA2. NIGHT SHOT switch (Lens block) .................................OFF3. FOCUS switch (KP-CX2670 block) ..................... MANUAL4. BACK LIGHT switch (KP-CX2670 block) .....................OFF5. COLOR SLOW S/ SUPER NS switch (JK-218 board) ... OFF6. DEMO MODE (Menu setting) ........................................OFF7. STEADY SHOT (Menu setting) ...................................... OFF8. DIGITAL ZOOM (Menu setting) ....................................OFF
9. 16 : 9 WIDE (Menu setting) ............................................OFF10. PROGRAM AE (Menu setting) ................................... AUTO11. PICTURE EFFECT (Menu setting) .................................OFF12. DIGITAL EFFECT (Menu setting) .................................. OFF13. WHITE BALANCE (Menu setting) ............................ AUTO14. AUTO SHUTTER (Menu setting) ...................................OFF15. DISPLAY (Menu setting) .................................. V-OUT/LCD16. DISPLAY (CK-108 board) ............................................... ON
5-8
DCR-TRV24E/TRV25E/TRV27E
1-2. INITIALIZATION OF 8, A, B, C, D, E, F,1B, 1E, 1F PAGE DATA
Note: When reading or writing the 1B, 1E or 1F page data, select page: 0,address: 10, and set data: 01, then select B, E or F page. The 1B, 1Eor 1F page can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
[Connection of the power supply during the initialization of thedata.]1) Connect the regulated power supply and the digital voltmeter
to the battery terminal as shown in Fig. 5-1-6.2) Adjust the output voltage of the regulated power supply so that
the digital voltmeter display is 6.0 ± 0.1Vdc.3) Turn off the power supply.4) Turn on the HOLD switch of the adjustment remote
commander.5) Turn on the power supply.6) Perform the initialization of the data.Note: This is normal though the following message is indicated on the
LCD screen.“FOR InfoLITHIUM BATTERY ONLY”
[Initialization Procedure]1. Initialization of A, D page data2. Initialization of B, 1B page data3. Initialization of 8, C page data4. Initialization of E, F, 1E, 1F page data
Fig. 5-1-6.
Digital volt meter
Battery terminal
Regulated power supply
5-9
DCR-TRV24E/TRV25E/TRV27E
1-2-1. INITIALIZATION OF A, D PAGE DATA
Note: The data of page: 0, address: 10 must be “00”.
1. Initializing the A, D Page Data
Note1: If the A, D page data has been initialized, the following adjustmentsneed to be performed again.1) Modification of A, D page data
Note2: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page A
Adjusting Address 10 to FF
Adjusting page D
Adjusting Address 10 to 67
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 7 03 84 Set the data.
4 7 00 Set the following data.20 (Initializing A page)22 (Initializing D page)28 (Initializing A and D pages)
5 7 01 Set the following data, and pressPAUSE button.20 (Initializing A page)22 (Initializing D page)28 (Initializing A and D pages)
6 7 02 Check that the data changes to “01”
7 Perform “Modification of A, DPage Data”.
2. Modification of A, D Page DataIf the A, D page data has been initialized, change the data of the“Fixed data-2” address shown in the following tables by manualinput.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
Processing after Completing Modification of A, D Page data
Order Page Address Data Procedure
1 2 00 29 Set the data.
2 2 01 29 Set the data, and press PAUSEbutton.
Note: If the following symptoms occur after completing of the“Modification of A, D page data”, check that the data of the “Fixeddata-2” addresses of A and D page are same as those of the samemodel of the same destination.1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.2) The power is shut off so that unit cannot operate.
3. A Page Table
Note1: The data of page: 0, address: 10 must be“00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, D
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of A, D
Page Data”).
Address00 to 0F
10 to 17
18
19
1A
1B to 31
32
33
34 to 59
5A
5B to 61
62
63
64 to CF
D0
D1
D2 to FF
Remark
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 5-1-2.
5-10
DCR-TRV24E/TRV25E/TRV27E
4. D Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, D
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of A, D
Page Data”).
00 to 0F
10
11 to 15
16
17 to 21
22
23
24
25
26
27 to 29
2A
2B
2C
2D
2E to 36
37
38
39
3A
3B to 56
57
58
59
5A
5B
5C
5D
5E
5F to 67
00 Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Address RemarkInitial value
Table. 5-1-3.
5-11
DCR-TRV24E/TRV25E/TRV27E
1-2-2. INITIALIZATION OF B, 1B PAGE DATA
Note: When reading or writing the B page data, select page: 0, address:10, and set data: 00.When reading or writing the 1B page data, select page: 0, address:10, and set data: 01, then select B page. The 1B page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
1. Initializing the B, 1B Page DataNote1: If “Initializing the B, 1B Page Data” is performed, all data
of the B page and 1B page will be initialized. (It isimpossible to initialize a single page.)
Note2: If the B, 1B page data has been initialized, the followingadjustments need to be performed again.1) Modification of B, 1B page data
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page B
Adjusting Address 00 to FF
Adjusting page 1B
Adjusting Address 00 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 5 02 FF Set the data.
4 5 01 F3 Set the data, and press PAUSEbutton.
5 5 00 01 Set the data, and press PAUSEbutton.
6 5 02 Check that the data changes to “00”.
7 Perform “Modification of B, 1BPage Data”.
2. Modification of B, 1B Page DataIf the B, 1B page data has been initialized, change the data of the“Fixed data-2” address shown in the following tables by manualinput.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) When changing the B page data, select page: 0, address: 10,
and set data: 00.3) When changing the 1B page data, select page: 0, address: 10,
and set data: 01.After completing the modification of 1B page data, reset thedata of this address to “00”.
4) New data for changing are not shown in the tables becausethey are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.5) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
Processing after Completing Modification of B, 1B Page data:
Order Page Address Data Procedure
1 0 10 00 Set the data.
2 2 00 29 Set the data.
3 2 01 29 Set the data, and press PAUSEbutton.
3. B Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1B
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of B, 1B
Page Data”).
Table. 5-1-4.
4. 1B Page TableNote1: When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1BPage Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of B, 1BPage Data”).
Table. 5-1-5.
Address00 to FF
RemarkFixed data-1
Address00 to FF
RemarkFixed data-1
5-12
DCR-TRV24E/TRV25E/TRV27E
1-2-3. INITIALIZATION OF 8, C PAGE DATANote: The data of page: 0, address: 10 must be “00”.
1. Initializing the 8, C Page Data
Note1: If “Initializing the 8, C Page Data” is performed, all dataof the 8 page and C page will be initialized. (It isimpossible to initialize a single page.)
Note2: If the 8, C page data has been initialized, following adjustmentsneed to be performed again.1) Modification of 8, C page data2) Serial No. input3) Viewfinder system adjustments4) LCD system adjustments5) Servo and RF system adjustments6) Video system adjustments
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page 8
Adjusting Address 00 to A3
Adjusting page C
Adjusting Address 10 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 3 81 Check that the data is “00”.
4 3 80 0C Set the data, and press PAUSEbutton.
5 3 80 Check that the data changes to “1C”.
6 Perform “Modification of 8, CPage Data”.
2. Modification of 8, C Page DataIf the 8, C page data has been initialized, change the data of the“Fixed data-2” address shown in the following table by manual input.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.If not, change the data to the initial value.
Processing after Completing Modification of 8, C Page data
Order Page Address Data Procedure
1 2 00 29 Set the data.
2 2 01 29 Set the data, and press PAUSEbutton.
3. 8 Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of 8, C
Page Data”).
Table. 5-1-6.
00 to 18
19
1A to 28
29
2A to 2E
2F
30 to 3A
3B
3C to 49
4A
4B to 51
52
53 to 59
5A
5B to 79
7A
7B
7C
7D
7E
7F
80
81
82
83
84 to 89
8A
8B
8C
8D
8E
8F
90
91
92
93
94 to A3
08
00
46
01
02
00
00
00
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Serial No. input
Fixed data-1
Address RemarkInitial value
5-13
DCR-TRV24E/TRV25E/TRV27E
4. C Page TableNote1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of 8, C
Page Data”).
00 to 0F
10
11
12
13
14 to 15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23 to 24
25
26
27
28
29
2A to 2B
2C
2D to 4E
4F
50
51
52
53
54
55
56
57
58
59 to 5E
5F
60
61
62
63
64
65
66
67
68
69
6A
EE
00
00
00
E0
2A
2A
32
32
25
3E
3E
DC
99
88
E3
A1
04
20
03
87
6F
97
80
80
37
80
70
80
30
C0
80
80
50
Switching position adj.
Fixed data-1
CAP FG duty adj.
Fixed data-1
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL fo adj.
APC adj.
LPF fo adj.
Fixed data-1
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF fo adj.
PLL fo adj.
Fixed data-1
APC adj.
Fixed data-1
Fixed data-2
VCO adj. (EVF)
Fixed data-2
RGB AMP adj. (EVF)
Fixed data-1
White balance adj. (EVF)
Contrast adj. (EVF)
Fixed data-1
Fixed data-2
VCO adj. (LCD)
V COM adj. (LCD)
RGB AMP adj. (LCD)
Fixed data-1
COM AMP adj. (LCD)
White balance adj. (LCD)
Contrast adj. (LCD)
Fixed data-1
Address RemarkInitial value
Address RemarkInitial value
6B
6C
6D to 71
72
73 to 75
76
77 to 79
7A
7B to 80
81
82
83 to 88
89
8A
8B
8C
8D to A9
AA
AB
AC
AD
AE
AF
B0 to C0
C1
C2
C3
C4
C5
C6
C7 to C8
C9
CA
CB
CC
CD
CE
CF to D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
5-14
DCR-TRV24E/TRV25E/TRV27E
Table. 5-1-7.
Address RemarkInitial value
E2
E3
E4 to E7
E8
E9
EA
EB
EC
ED
EE
EF
F0 to F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
00
00
00
00
00
00
00
00
00
00
00
00
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Emergency memory address
C Page
5-15
DCR-TRV24E/TRV25E/TRV27E
1-2-4. INITIALIZATION OF E, F, 1E, 1F PAGE DATANote: When reading or writing the E, F page data, select page: 0, address:
10, and set data: 00.When reading or writing the 1E or 1F page data, select page: 0,address: 10, and set data: 01, then select E or F page. The 1E or 1Fpage can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
1. Initializing the E, F, 1E, 1F Page Data
Note1: If “Initializing the E, F, 1E, 1F Page Data” is performed,all data of the E page, F page, 1E page and 1F page willbe initialized. (It is impossible to initialize a single page.)
Note2: If the E, F, 1E, 1F page data has been initialized, followingadjustments need to be performed again.1) Modification of E, F, 1E, 1F page data2) 54MHz origin osc. adjustment3) Camera system adjustments
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page E
Adjusting Address 00 to FF
Adjusting page F
Adjusting Address 10 to FF
Adjusting page 1E
Adjusting Address 00 to BF
Adjusting page 1F
Adjusting Address 00 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 6 01 2F Set the data, and press PAUSEbutton.
4 6 03 01 Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”.
6 Perform “Modification of E, F,1E, 1F Page Data”.
2. Modification of E, F, 1E, 1F Page DataIf the E, F, 1E, 1F page data has been initialized, change the data ofthe “Fixed data-2” address shown in the following table by manualinput.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) When changing the E, F page data, select page: 0, address: 10,
and set data: 00.3) When changing the 1E, 1F page data, select page: 0, address:
10, and set data: 01.After completing the modification of 1E, 1F page data, resetthe data of this address to “00”.
4) New data for changing are not shown in the tables becausethey are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.5) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.If not, change the data to the initial value.
Processing after Completing Modification of E, F, 1E, 1F Pagedata
Order Page Address Data Procedure
1 0 10 00 Set the data.
2 2 00 29 Set the data.
3 2 01 29 Set the data, and press PAUSEbutton.
4 Perform “54MHz Origin Osc.Adjustment” of the camerasystem adjustment.
5-16
DCR-TRV24E/TRV25E/TRV27E
3. E Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
1E, 1F Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
1E, 1F Page Data”).
Table. 5-1-9.
Address Remark00 to 07
08
09
0A
0B
0C to 0D
0E
0F to 1A
1B
1C
1D
1E to 1F
20
21
22
23
24
25
26
27
28 to 37
38
39
3A to 3B
3C
3D
3E
3F
40 to 41
42
43 to 45
46
47
48 to 53
54
55
56 to 65
66
67
68
69
6A to 6E
6F
70
71 to 85
86
87 to DF
E0
E1
E2
E3
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
E4
E5
E6
E7
E8
E9
EA
EB to FF
Address RemarkFixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
5-17
DCR-TRV24E/TRV25E/TRV27E
4. F Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
1E, 1F Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
1E, 1F Page Data”).
00 to FF
10
11 to 12
13
14
15
16
17
18
19
1A
1B
1C to 2F
30
31
32
33
34
35
36
37
38
39
3A to 3F
40
41
42 to 44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
40
28
70
28
40
80
D8
A0
80
7A
4D
3E
64
59
96
7A
2C
26
01
E8
3F
10
39
C2
1E
2E
00
00
00
00
6E
19
00
19
00
00
00
80
80
54MHz origin osc. adj.
Fixed data-1
HALL adj.
MAX GAIN adj.
AWB & LV standard data input
Fixed data-1
AWB & LV standard data input
Auto white balance adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Flange back adj.
Fixed data-1
MR adj.
Address RemarkInitial value
Address RemarkInitial value
5C
5D
5E
5F
60
61
62
63
64
65
6D to 71
72
73 to 75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85
86
87
88
89
8A
8B
8C to 97
98
99
9A
9B
9C
9D to A7
A8
A9 to CF
D0
D1 to D6
D7
D8 to D9
DA
DB
DC to DD
DE
DF
E0 to E6
E7
80
80
40
C0
40
C0
40
C0
40
C0
40
00
34
00
30
00
2A
00
28
00
40
3A
31
31
35
1E
80
80
80
80
80
80
MR adj.
Fixed data-1
Fixed data-2
Fixed data-1
Mechanical shutter adj.
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2(Modified data. Copy the
data built in the same model.)
Fixed data-1
Fixed data-2
5-18
DCR-TRV24E/TRV25E/TRV27E
Table. 5-1-10.
Address RemarkInitial value
E8 to F4
F5
F6
F7
F8
F9
FA to FD
FE
FF
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
F Page5. 1E Page Table
Note1: When reading or writing the 1E page data, select page: 0, address:10, and set data: 01, then select E page. The 1E page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,1E, 1F Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of E, F,1E, 1F Page Data”).
Table. 5-1-11.
Address RemarkInitial value
00 to 0F
10
11 to 1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35 to 37
38
39 to 51
52
53
54
55
56
57 to 71
72
73
74 to 80
81
82
83 to 84
85
86
87 to BF
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
Fixed data-1
Fixed data-2
Fixed data-1
Black defective CCD adj.
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
5-19
DCR-TRV24E/TRV25E/TRV27E
6. 1F Page Table
Note1: When reading or writing the 1F page data, select page: 0, address:10, and set data: 01, then select F page. The 1F page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,1E, 1F Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of E, F,1E, 1F Page Data”).
00 to 38
39
3A to 44
45
46
47 to 4F
50
51
52
53
54
55 to 5A
5B
5C
5D
5E to 6F
70
71
72 to A1
A2
A3 to AB
AC
AD
AE to B0
B1
B2
B3
B4
B5 to B8
B9
BA
BB to C9
CA
CB
CC
CD
CE
CF to D1
D2
D3
D4 to FF
Address RemarkFixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 5-1-12.
5-20
DCR-TRV24E/TRV25E/TRV27E
1-3. CAMERA SYSTEM ADJUSTMENTSBefore perform the camera system adjustments (except for “54MHzOrigin Oscillation Adjustment”), check that the specified values of“VIDEO SYSTEM ADJUSTMENTS” are satisfied.And check that the data of page: 0, address: 10 is “00”. If not, setdata: 00 to this address.
1. 54MHz Origin Oscillation Adjustment (VC-281 board)Set the frequency of the clock for synchronization.If deviated, the synchronization will be disrupted and the color willbecome inconsistent.
Subject Not required
Measurement Point Pin wg of IC1501Or Pin eg of IC2401
Measuring Instrument Frequency counter
Adjustment Page F
Adjustment Address 10
Specified Value Pin wg of IC1501f=27000000 ± 136Hz
Pin eg of IC2401f=13500000 ± 68Hz
Note1: The data of page: 0, address: 10 must be “00”.Note2: When open the VA-117 board, use the following extension cable
between the VC-281 board CN1007 and VA-117 board CN4002.J-6082-352-A (100P, 0.5mm)
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 F 10 Change the data and set thefrequency (f) to the specifiedvalue.
3 F 10 Press PAUSE button.
4 0 01 00 Set the data.
VC-281 board (SIDE A)
VC-281 board (SIDE B)
Fig. 5-1-7.
13
24
2536
12148
37IC1501
1
2021 40
80 61
41
60
IC2401
5-21
DCR-TRV24E/TRV25E/TRV27E
2. HALL Adjustment
For detecting the position of the lens iris and ND filter, adjust AMPgain and offset.
Subject Not required
Measurement Point Display data of page 1 (Note1)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 13 to 18
Specified Value 1 D5 to DB
Specified Value 2 25 to 2B
Specified Value 3 D5 to DB
Specified Value 4 25 to 2B
Note1: Displayed data of page 1 of the adjustment remote commander.1 : XX : XX
IRIS display dataND display data
Note2: The data of page: 0, address: 10 must be “00”.
Switch setting:POWER .................................................................. CAMERA
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 94 00 Set the data.
3 6 95 00 Set the data.
4 6 01 6D Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”. (Note3)
6 6 01 00 Set the data, and press PAUSEbutton.
Note3: The adjustment data will be automatically input to page: F, address:13 to 18.
Checking method:
Order Page Address Data Procedure
1 0 03 03 Set the data.
2 6 01 03 Set the data, and press PAUSEbutton.
3 1 Check that the IRIS display data(Note1) satisfies the specifiedvalue 1.
4 6 01 01 Set the data, and press PAUSEbutton.
5 1 Check that the IRIS display data(Note1) satisfies the specifiedvalue.2.
6 6 01 69 Set the data, and press PAUSEbutton.
7 1 Check that the ND display data(Note1) satisfies the specifiedvalue 3.
8 6 01 6B Set the data, and press PAUSEbutton.
9 1 Check that the ND display data(Note1) satisfies the specifiedvalue.4.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 94 00 Set the data.
2 6 95 00 Set the data.
3 6 01 00 Set the data, and press PAUSEbutton.
4 0 03 00 Set the data.
5 0 01 00 Set the data.
5-22
DCR-TRV24E/TRV25E/TRV27E
3. MR AdjustmentThe MR (Magnet resistor) adjustment of the inner focus lens iscarried out automatically. In whichever case, the focus will bedeviated during auto focusing/manual focusing.
Subject Not required
Measurement Point Adjustment remote commander
Measuring Instrument
Adjustment Page F
Adjustment Address 58, 5A to 65
Specified Value1 40 to C0
Specified Value2 03 to 78
Specified Value3 88 to F8
Note1: Make the lens horizontal and perform this adjustment.Note2: Perform this adjustment before “Flange Back Adjustment”.Note3: The data of page: 0, address: 10 must be “00”.Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 01 BD Set the data, and press PAUSEbutton.
3 6 02 Check that the data changes to“01”. (Note5)
4 F 5A Check that the data satisfies thespecified value 1.
5 F 5B Check that the data satisfies thespecified value 1.
6 F 5C Check that the data satisfies thespecified value 1.
7 F 5D Check that the data satisfies thespecified value 1.
8 F 5E Check that the data satisfies thespecified value 2.
9 F 5F Check that the data satisfies thespecified value 3.
10 F 60 Check that the data satisfies thespecified value 2.
11 F 61 Check that the data satisfies thespecified value 3.
12 F 62 Check that the data satisfies thespecified value 2.
13 F 63 Check that the data satisfies thespecified value 3.
14 F 64 Check that the data satisfies thespecified value 2.
15 F 65 Check that the data satisfies thespecified value 3.
Note5: The adjustment data will be automatically input to page: F, address:58, 5A to 65.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 0 01 00 Set the data.
5-23
DCR-TRV24E/TRV25E/TRV27E
4. Flange Back Adjustment (Using Minipattern Box)The inner focus lens flange back adjustment is carried outautomatically. In whichever case, the focus will be deviated duringauto focusing/manual focusing.
Subject Siemens star chart with ND filter forthe minipattern box (Note1)
Measurement Point Adjustment remote commander
Measuring Instrument
Adjustment Page F
Adjustment Address 48 to 58
Specified Value Data of page: F, address: 57 is “00” to“0B”.
Note1: Dark Siemens star chart.Note2: This adjustment should be carried out upon completion of the
following adjustments.“HALL Adjustment”, “MR Adjustment”
Note3: Make the lens horizontal and perform this adjustment.Note4: The data of page: 0, address: 10 must be “00”.Note5: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF
Preparations:1) The minipattern box is installed as shown in the following
figure.Note: The attachment lenses are not used.
2) Install the minipattern box so that the distance between it andthe front of the lens of the camcorder is less than 3cm.
3) Make the height of the minipattern box and the camcorder equal.4) Check that the output voltage of the regulated power supply is
the specified voltage.5) Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposurescreen coincide.
Specified voltage: The specified voltage varies according to theminipattern box, so adjust the power supplyoutput voltage to the specified voltage writtenon the sheet which is supplied with theminipattern box.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 01 13 Set the data, and press PAUSEbutton. (Note3)
3 6 01 27 Set the data, and press PAUSEbutton.
4 6 02 Check that the data changes to“01”. (Note6)
5 F 57 Check the data is “00” to “0B”.
Note6: The adjustment data will be automatically input to page: F, address:48 to 58.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 0 01 00 Set the data.
3 Turn off the power and turn onagain.
4 Perform “Flange Back Check”.
Fig. 5-1-8.
Minipattern box
Below 3 cm
Camcorder
Camera table
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supplyOutput voltage : Specified voltage ±0.01Vdc
Output current : more than 3.5A
5-24
DCR-TRV24E/TRV25E/TRV27E
5. Flange Back Adjustment(Using Flange Back Adjustment Chart and SubjectMore Than 500m Away)
The inner focus lens flange back adjustment is carried outautomatically. In whichever case, the focus will be deviated duringauto focusing/manual focusing.
5-1. Flange Back Adjustment (1)
Subject Flange back adjustment chart(2.0 m from the front of the protectionglass)(Luminance: 350 ± 50 lux)
Measurement Point Adjustment remote commander
Measuring Instrument
Adjustment Page F
Adjustment Address 48 to 58
Specified Value Data of page: F, address: 57 is “00” to“0B”.
Note1: This adjustment should be carried out upon completion of thefollowing adjustments.
“HALL Adjustment”, “MR Adjustment”Note2: Make the lens horizontal and perform this adjustment.Note3: The data of page: 0, address: 10 must be “00”.Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF
Preparations:1) Check that at both the zoom lens TELE end and WIDE end,
the center of the chart for the flange back adjustment and centerof the exposure screen coincide.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 01 13 Set the data, and press PAUSEbutton. (Note2)
3 6 01 15 Set the data, and press PAUSEbutton.
4 6 02 Check that the data changes to“01”. (Note5)
5 F 57 Check the data is “00” to “0B”.
Note5: The adjustment data will be automatically input to page: F, address:48 to 58.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 0 01 00 Set the data.
3 Turn off the power and turn onagain.
4 Perform “Flange BackAdjustment (2)”
5-2. Flange Back Adjustment (2)Perform this adjustment after performing “Flange Back Adjustment(1)”.
Subject Subject more than 500m away(Subjects with clear contrast such asbuildings, etc.)
Measurement Point Check operation on TV monitor
Measuring Instrument
Adjustment Page F
Adjustment Address 48 to 58
Note1: Make the lens horizontal and perform this adjustment.Note2: The data of page: 0, address: 10 must be “00”.Note3: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF
Preparations:1) Set the zoom lens to the TELE end and expose a subject that is
more than 500m away (subject with clear contrast such asbuilding, etc.). (Nearby subjects less than 500m away shouldnot be in the screen.)
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 01 13 Set the data, and press PAUSEbutton. (Note2)
3 Place a ND filter on the lens sothat the optimum image isobtain.
4 6 01 29 Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”. (Note4)
Note4: The adjustment data will be automatically input to page: F, address::48 to 58.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 0 01 00 Set the data.
3 Turn off the power and turn onagain.
4 Perform “Flange Back Check”
5-25
DCR-TRV24E/TRV25E/TRV27E
6. Flange Back Check
Subject Siemens star(2.0m from the front of the lens)(Luminance : approx. 200 lux)
Measurement Point Check operation on TV monitor
Measuring Instrument
Specified Value Focused at the TELE end and WIDEend.
Note1: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT (Menu display) ........................................OFF
Note2: When the auto focus is ON, the lens can be checked if it is focusedor not by observing the data on the page 1 of the adjustment remotecommander.
1) Select page: 0, address: 03, and set data: 0F.2) Page 1 shows the state of the focus.
1 : 00 : XXOdd: FocusedEven: Unfocused
Checking method:1) Select page: 6, address: 40, and set data: 01.2) Select page: 6, address: 41, and set data: 01.3) Place the Siemens star 2.0m from the front of the lens.4) To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.5) Shoot the Siemens star with the zoom TELE end.6) Turn on the auto focus.7) Check that the lens is focused (Note2).8) Select page: 6, address: 21, and set data: 10.9) Shoot the Siemens star with the zoom WIDE end.10) Observe the TV monitor and check that the lens is focused.
Processing after Completing Adjustments:1) Select page: 6, address: 21, and set data: 00.2) Select page: 6, address: 40, and set data: 00.3) Select page: 6, address: 41, and set data: 00.4) Select page: 0, address: 03, and set data: 00.
7. MAX GAIN AdjustmentSetting the minimum illumination.If it is not consistent, the image level required for taking subjects inlow illuminance will not be produced (dark).
Subject Clear chart (Approx. 1m from thefront of the lens) (Note1)
Adjustment Page F
Adjustment Address 19
Note1: Shoot the clear chart with the zoom WIDE end. And adjust thedirection of the camera so that the chart is located in the center ofthe screen.
Note2: The data of page: 0, address: 10 must be “00”.Note3: This adjustment should be carried out upon completion of “Flange
Back Adjustment”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF3) ZOOM .................................................................... WIDE end
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 2C 01 Set the data.
3 6 40 01 Set the data.
4 6 41 01 Set the data.
5 6 96 28 Set the data.
6 6 97 00 Set the data.
7 6 01 6F Set the data, and press PAUSEbutton.
8 6 02 Check that the data changes to“01”. (Note4)
Note4: The adjustment data will be automatically input to page: F, address:19.
Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 2C 00 Set the data.
2 6 40 00 Set the data.
3 6 41 00 Set the data.
4 6 96 00 Set the data.
5 6 97 00 Set the data.
6 6 01 00 Set the data, and press PAUSEbutton.
7 0 01 00 Set the data.
5-26
DCR-TRV24E/TRV25E/TRV27E
8. Picture Frame Setting
Subject Color bar chart(Color reproduction adjustment frame)(1.5m from the front of the lens)
Measurement Point Video output terminal
Measuring Instrument Oscilloscope and TV monitor
Specified Value A=B, C=D, E=F
Note1: The following adjustments should be carried out upon completionof “Flange Back Adjustment”.
Note2: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF3) FOCUS .................................................................. MANUAL4) DIGITAL ZOOM (Menu display) ...................................OFF5) STEADY SHOT (Menu display) .....................................OFF
Setting method:1) Adjust the zoom and the camera direction, and set to the
specified position.2) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in followingadjustments using “Color reproduction adjustment frame”.
Check on the oscilloscope
1. Horizontal period
Fig. 5-1-9.
2. Vertical period
Fig. 5-1-10.
Check on the monitor TV (Underscanned mode)
Fig. 5-1-11.
A=B C=D
A
B C
D
E=F
V
E F
Color bar chart picture frame Monitor TV picture frame
5-27
DCR-TRV24E/TRV25E/TRV27E
9. Color Reproduction AdjustmentAdjust the color Separation matrix coefficient so that proper colorreproduction is produced.
Subject Color bar chart(Color reproduction adjustment frame)
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Adjustment Page F
Adjustment Address 37, 39, 40, 41
Specified Value All color luminance points shouldsettle within each color reproductionframe.
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF3) FOCUS .................................................................. MANUAL4) DIGITAL ZOOM (Menu display) ................................... OFF5) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:1) Select page: 0, address: 01, and set data: 01.2) Select page: 6, address: 9D, and set data: 18.3) Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.4) Select page: F, address: F0, set data: B7, and press the PAUSE
button.5) Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the colorreproduction frame.
6) Change the data of page: F, address: 37, 39, 40 and 41, andsettle each color luminance point in each color reproductionframe.
Note: Be sure to press the PAUSE button of the adjustment remotecommander before changing the addresses. If not, the new data willnot be written to the memory.
Processing after Completing Adjustments:1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.2) Select page: 6, address: 9D, and set data: 00.3) Select page: 0, address: 01, and set data: 00.
10. Auto White Balance & LV Standard Data InputAdjust the white balance reference at 3200K, and adjust the normalcoefficient of the light value.
Subject Clear chart(Color reproduction adjustment frame)
Measurement Point Display data of page 1 (Note5)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 1A, 1B, 30 to 33
Specified Value 0FF0 to 1010
Note1: This adjustments should be carried out upon completion of “ColorReproduction Adjustment”.
Note2: After the power is turned on, this adjustment can be done onlyonce.
Note3: The data of page: 0, address: 10 must be “00”.Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.Note5: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX Display data
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF3) FOCUS .................................................................. MANUAL4) DIGITAL ZOOM (Menu display) ...................................OFF5) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 Wait for 2 sec.
3 6 01 11 Set the data, and press PAUSEbutton.
4 6 01 0D Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”. (Note6)
6 0 03 1E Set the data.
1 Check that the display data (Note5)satisfies the specified value.
Note6: The adjustment data will be automatically input to page: F, address:1A, 1B, 30 to 33.
Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 0 03 00 Set the data.
3 0 01 00 Set the data.
4 Perform “Auto White BalanceAdjustment”.
Burst position
Fig. 5-1-12.
5-28
DCR-TRV24E/TRV25E/TRV27E
11. Auto White Balance AdjustmentAdjust to the proper auto white balance output data.If it is not correct, auto white balance and color reproducibility willbe poor.
Subject Clear chart(Color reproduction adjustment frame)
Filter Filter C14 for color temperaturecorrection
Measurement Point Display data of page 1 (Note5)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 34, 35
Specified Value R ratio: 2B3C to 2C3CB ratio: 57C8 to 58C8
Note1: This adjustments should be carried out upon completion of “AutoWhite Balance & LV Standard Data Input”.
Note2: After the power is turned on, this adjustment can be done onlyonce.
Note3: The data of page: 0, address: 10 must be “00”.Note4: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XXDisplay data
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF3) FOCUS .................................................................. MANUAL4) DIGITAL ZOOM (Menu display) ...................................OFF5) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:
Order Page Address Data Procedure
1 Place the C14 filter for colortemperature correction on thelens.
2 0 01 01 Set the data.
3 F 44 Write down the data.
4 F 44 2B Set the data, and press PAUSEbutton.
5 F 45 Write down the data.
6 F 45 BC Set the data, and press PAUSEbutton.
7 F 46 Write down the data.
8 F 46 58 Set the data, and press PAUSEbutton.
9 F 47 Write down the data.
10 F 47 48 Set the data, and press PAUSEbutton.
11 6 01 83 Set the data, and press PAUSEbutton.
12 6 01 81 Set the data, and press PAUSEbutton.
13 6 02 Check that the data changes to“01”. (Note5)
14 6 01 3F Set the data, and press PAUSEbutton.
15 0 03 04 Set the data.
16 1 Check that the display data(Note4) satisfies the R ratiospecified value.
17 0 03 05 Set the data.
18 1 Check that the display data(Note4) satisfies the B ratiospecified value.
Note5: The adjustment data will be automatically input to page: F, address:34, 35.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 F 44 Set the data that is written downat step 3, and press PAUSE button.
2 F 45 Set the data that is written downat step 5, and press PAUSE button.
3 F 46 Set the data that is written downat step 7, and press PAUSE button.
4 F 47 Set the data that is written downat step 9, and press PAUSE button.
5 6 01 00 Set the data, and press PAUSEbutton.
6 0 03 00 Set the data.
7 0 01 00 Set the data.
5-29
DCR-TRV24E/TRV25E/TRV27E
12. White Balance Check
Subject Clear chart(Color reproduction adjustment frame)
Filter Filter C14 for color temperaturecorrection ND filter 1.0 and 0.4 and 0.1
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Specified Value Fig. 5-1-13. A to B
Note1: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF3) FOCUS .................................................................. MANUAL4) DIGITAL ZOOM (Menu display) ................................... OFF5) STEADY SHOT (Menu display) .....................................OFF
Checking method:
Order Page Address Data Procedure
Indoor white balance check
1 Check that the lens is notcovered with either filter.
2 6 01 0F Set the data, and press PAUSEbutton.
3 Check that the center of thewhite luminance point is withinthe circle shown Fig. 5-1-13. A.
4 6 01 00 Set the data, and press PAUSEbutton.
Outdoor white balance check
5 Place the C14 filter on the lens.
6 6 01 3F Set the data, and press PAUSEbutton.
7 Check that the center of thewhite luminance point is withinthe circle shown Fig. 5-1-13. B.
8 Remove the C14 filter.
LV data check
9 Place the ND filter 1.5(1.0+0.1+0.4) on the lens.
10 6 01 00 Set the data, and press PAUSEbutton.
11 0 03 06 Set the data.
12 1 Check that the display data(Note2) satisfies the specifiedvalue.Specified value: 8000 to 8BC0
Note2: Displayed data of the adjustment remote commander.1 : XX : XX
Display data
Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 0 03 00 Set the data.
Fig. 5-1-13(A).
Fig. 5-1-13(B).
R-Y 2mm
B-Y
2mm
R-Y
B-Y1mm
1mm
3mm
3mm
5-30
DCR-TRV24E/TRV25E/TRV27E
13. Mechanical Shutter Adjustment
Adjustment Page F
Adjustment Address 76 to 8B
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:1) Select page: 0, address: 01, and set data: 01.2) Input the following data to page: F, addresses: 76 to 8B.Note: Press the PAUSE button of the adjustment remote commander each
time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85
86
87
88
89
8A
8B
Data4B
00
3D
00
35
00
2F
00
27
00
66
7D
7D
6F
61
1F
80
80
80
80
80
80
14. Black Defective CCD AdjustmentDetect the black defective positions of the CCD imager.
Subject Clear chart (All white)(Approx. 40cm from the front of the lens)
Adjustment Page 1E (Note1)
Adjustment Address 20 to 2F
Note1: When reading or writing the 1E page data, select page: 0, address:10, and set data: 01, then select E page. The 1E page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
Note2: This adjustment should be carried out upon completion of “FlangeBack Adjustment”.
Note3: Check that the data of page: 6, address: 02 is “00”. If not, to page:6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 6 2C 01 Set the data.
4 6 9C 01 Set the data.
5 6 90 50 Set the data.
6 6 91 01 Set the data.
7 6 92 00 Set the data.
8 6 93 01 Set the data.
9 6 01 79 Set the data, and press PAUSEbutton.
10 Adjust the direction of thecamera so that the whole of thescreen is white.
11 6 01 8D Set the data, and press PAUSEbutton.
12 6 02 Check that the data changes to“01”. (Note4)
Note4: The adjustment data will be automatically input to page: 1E,address: 20 to 2F
Processing after Completing Adjustments
Order Page Address Data Procedure
1 0 10 00 Set the data.
2 6 01 00 Set the data, and press PAUSEbutton.
3 6 2C 00 Set the data.
4 6 9C 00 Set the data.
5 6 90 00 Set the data.
6 6 91 00 Set the data.
7 6 93 00 Set the data.
8 0 01 00 Set the data.
5-31
DCR-TRV24E/TRV25E/TRV27E
15. Steady Shot Check
Precautions on the Parts ReplacementThere are two types of repair parts.
Type A: CG-L43A0Type B: CG-L43A1
Replace the broken sensor with a same type sensor. If replace withother type parts, the image will vibrate up and down or left andright during hand-shake correction operations.
Precautions on Angular Velocity SensorThe sensor incorporates a precision oscillator. Handle it with careas if it dropped, the balance of the oscillator will be disrupted andoperations will not be performed properly.
Subject Arbitrary
Measurement Point Display data of page 1 (Note1)
Measuring Instrument Adjustment remote commander
Specified Value 2B00 to 4B00
Note1: Displayed data of the adjustment remote commander.1 : XX : XX
Display dataNote2: The data of page: 0, address: 10 must be “00”.
Switch setting:1) STEADY SHOT (Menu display) ...................................... ON2) ZOOM .................................................................... TELE end
Adjusting method:
Order Page Address Data Procedure
Pitch sensor check(JK-217 board SE5302)
1 0 03 11 Set the data.
2 1 Check that the display data(Note1) satisfies the specifiedvalue.
Yaw sensor check(JK-217 board SE5301)
3 0 03 12 Set the data.
4 1 Check that the display data(Note1) satisfies the specifiedvalue.
Processing after Completing Adjustments
Order Page Address Data Procedure
1 0 03 00 Set the data.
2 Move the camcorder, and checkthat the steady shot operationshave been performed normally
5-32
DCR-TRV24E/TRV25E/TRV27E
1-4. COLOR ELECTRONIC VIEWFINDERSYSTEM ADJUSTMENT
Note1: When replacing the LCD unit, be careful to prevent damagescaused by static electricity.
Note2: Before performing the adjustments, check the data of page: 0,address: 10 is “00”. If not, set data: 00 to this address.
Note3: As the PANEL CLOSE switch is attached to the cabinet (R), thiscabinet must be attached when performing adjustments.If you perform the adjustments with cabinet (R) removed, set thefollowing data.1) Select page: 3, address: C4, and set data: 67.2) Select page: 3, address: C5, and set data: 01.Reset the data after completing adjustment.1) Select page: 3, address: C4, and set data: 00.2) Select page: 3, address: C5, and set data: 00.
[Adjusting connector]Most of the measuring points for adjusting the viewfinder systemare concentrated in CN1002 of VC-281 board.Connect the Measuring Instruments via the CPC-8 jig (J-6082-388-A).The following table shows the Pin No. and signal name of CN1002.
Table 5-1-13.
1. VCO Adjustment (VA-117 board)Set the VCO free-run frequency. If deviated, the EVF screen will beblurred.
Mode Camera
Subject Arbitrary
Measurement Point Pin 5 of CN1002 of VC-281 board(EVF VCO)
Measuring Instrument Frequency counter
Adjustment Page C
Adjustment Address 51, 52
Specified Value f = 15625 ± 30Hz
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 51 Change the data and set the VCOfrequency (f) to the specified value.
3 C 51 Press PAUSE button.
4 C 51 Read the data, and this data isnamed D51.
5 Convert D51 to decimal notation,and obtain D51’. (Note2)
6 Calculate D52’ using followingequations (Decimal calculation)
When D51’ 24D52’ = D51’– 24
When D51’ < 24D52’ = 0
7 Convert D52’ to a hexadecimalnumber, and obtain D52. (Note2)
8 C 52 D52 Set the data, and press PAUSEbutton.
9 0 01 00 Set the data.
Note2: Refer to “Table 5-4-1. Hexadecimal-decimal Conversion Table”.
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameLANC SIG
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.
2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
CN1002
1 2
19 20
Remove the CPC lid.
Fig. 5-1-14.
5-33
DCR-TRV24E/TRV25E/TRV27E
2. RGB AMP Adjustment (VA-117 board)Set the D range of the RGB driver used to drive the LCD to thespecified value. If deviated, the LCD screen will become blackishor saturated (whitish).
Mode Camera
Subject Arbitrary
Measurement Point Pin 4 of CN1002 of VC-281 board(EVF VG)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 54
Specified Value A = 7.14 ± 0.10V
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 54 Change the data and set thevoltage (A) between the reversedwaveform pedestal and non-reversed waveform pedestal to thespecified value.
3 C 54 Press PAUSE button.
4 0 01 00 Set the data.
3. Contrast Adjustment (VA-117 board)Set the level of the VIDEO signal for driving the LCD to the specifiedvalue. If deviated, the screen image will be blackish or saturated(whitish).
Mode Camera
Subject Arbitrary
Measurement Point Pin 4 of CN1002 of VC-281 board(EVF VG)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 58
Specified Value A = 2.38 ± 0.10V
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 58 Change the data and set thevoltage (A) between the 100 IREand 0 IRE (pedestal) to thespecified value. (The data shouldbe “00” to “7F”.)
3 C 58 Press PAUSE button.
4 0 01 00 Set the data.
Pedestal
Pedestal
A
2H
3 steps peak
Pedestal
A
2H
Fig. 5-1-15. Fig. 5-1-16.
5-34
DCR-TRV24E/TRV25E/TRV27E
4. White Balance Adjustment (VA-117 board)
Correct the white balance.If deviated, the reproduction of the EVF screen may degenerate.
Mode Camera
Subject Arbitrary
Measurement Point Check on EVF screen
Measuring Instrument
Adjustment Page C
Adjustment Address 56, 57
Specified Value The EVF screen should not be colored.
Note1: Check the white balance only when replacing the following parts.If necessary, adjust them.1. LCD panel2. Light induction plate3. IC4201
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 56 80 Set the data, and press PAUSEbutton.
3 C 57 80 Set the data, and press PAUSEbutton.
4 C 57 Check that the EVF screen is notcolored. If not colored, proceed tostep 10.
5 C 56 Change the data so that the EVFscreen is not colored.
6 C 56 Press PAUSE button.
7 C 57 Change the data so that the EVFscreen is not colored.
8 C 57 Press PAUSE button.
9 C 57 If the EVF screen is colored,repeat steps 5 to 9.
10 0 01 00 Set the data.
5-35
DCR-TRV24E/TRV25E/TRV27E
1-5. LCD SYSTEM ADJUSTMENT
Note1: The back light (fluorescent tube) is driven by a high voltage ACpower supply. Therefore, do not touch the back light holder toavoid electrical shock.
Note2: When replacing the LCD unit, be careful to prevent damagescaused by static electricity.
Note3: Before performing the adjustments, check the data of page: 0,address: 10 is “00”. If not, set data: 00 to this address.
Switch setting:LCD BRIGHT(Menu setting) ............................................. Center.
[Adjusting connector]Most of the measuring points for adjusting the LCD system areconcentrated in CN1002 of the VC-281 board. Connect themeasuring instruments via the multi CPC-8 jig (J-6082-388-A). Thefollowing table shows the Pin No. and signal name of CN1002.
Table 5-1-14.
1. VCO Adjustment (PD-161 board)Set the VCO free-run frequency. If deviated, the LCD screen willbe blurred.
Mode VTR stop
Signal No signal
Measurement Point Pin 9 of CN1002 of VC-281 board(H START)
Measuring Instrument Frequency counter
Adjustment Page C
Adjustment Address 61, 62
Specified Value f = 15625 ± 30Hz
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 61 Change the data and set the VCOfrequency (f) to the specifiedvalue.
3 C 61 Press PAUSE button.
4 C 61 Read the data, and this data isnamed D61.
5 Convert D61 to decimal notation,and obtain D61’. (Note2)
6 Calculate D62’ using followingequations (Decimal calculation)[DCR-TRV24E/TRV25E]
When D61’ 26D62’ = D61’ – 26
When D61’ < 26D62’ = 0
[DCR-TRV27E]When D61’ 9
D62’ = D61’ – 9When D61’ < 9
D62’ = 0
7 Convert D62’ to a hexadecimalnumber, and obtain D62. (Note2)
8 C 62 D62 Set the data, and press PAUSEbutton.
9 0 01 00 Set the data.
Note2: Refer to “Table 5-4-1. Hexadecimal-decimal Conversion Table”.
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameLANC SIG
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.
2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
CN1002
1 2
19 20
Remove the CPC lid.
Fig. 5-1-17.
5-36
DCR-TRV24E/TRV25E/TRV27E
2. RGB AMP Adjustment (PD-161 board)Set the D range of the RGB decoder used to drive the LCD to thespecified value. If deviated, the LCD screen will become blackishor saturated (whitish).
Mode VTR stop
Signal No signal
Measurement Point Pin 7 of CN1002 of VC-281 board(PANEL VG)Ext. trigger: Pin qa of CN1002 of VC-281 board (PANEL COM)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 64
Specified Value A = 3.63 ± 0.05V (TRV24E/TRV25E)A = 3.64 ± 0.05V (TRV27E)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 64 Change the data and set thevoltage (A) between the reversedwaveform pedestal and non-reversed waveform pedestal to thespecified value. (The data shouldbe “00” to “3F”.)
3 C 64 Press PAUSE button.
4 0 01 00 Set the data.
3. Contrast Adjustment (PD-161 board)Set the level of the VIDEO signal for driving the LCD to the specifiedvalue. If deviated, the screen image will be blackish or saturated(whitish).
Mode VTR stop
Signal No signal
Measurement Point Pin 7 of CN1002 of VC-281 board(PANEL VG)Ext. trigger: Pin qa of CN1002 of VC-281 board (PANEL COM)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 69
Specified Value A = 3.37 ± 0.05V (TRV24E/TRV25E)A = 3.31 ± 0.05V (TRV27E)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 69 Change the data and set thevoltage (A) between the 100 IREand 0 IRE (pedestal) to thespecified value. (The data shouldbe “00” to “7F”.)
3 C 69 Press PAUSE button.
4 0 01 00 Set the data.
Fig. 5-1-18.
Pedestal
Pedestal
A
2H
100 IRE
Pedestal
A
2H
Fig. 5-1-19.
5-37
DCR-TRV24E/TRV25E/TRV27E
4. COM AMP Adjustment (PD-161 board)
Set the common electrode drive signal level of LCD to the specifiedvalue.
Mode VTR stop
Signal No signal
Measurement Point Pin qa of CN1002 of VC-281 board(PANEL COM)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 66
Specified Value A = 6.34 ± 0.05V (TRV24E/TRV25E)A = 6.14 ± 0.05V (TRV27E)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 66 Change the data and set thePANEL COM signal level (A) tothe specified value.
3 C 66 Press PAUSE button.
4 0 01 00 Set the data.
5. V COM Adjustment (PD-161 board)Set the DC bias of the common electrode drive signal of LCD to thespecified value.If deviated, the LCD display will move, producing flicker andconspicuous vertical lines.
Mode VTR stop
Signal No signal
Measurement Point Check on LCD display
Measuring Instrument
Adjustment Page C
Adjustment Address 63
Specified Value The brightness difference between thesection A and section B is minimum.
Note1: This adjustment should be carried out upon completion of thefollowing adjustments.
RGB AMP AdjustmentContrast AdjustmentCOM AMP Adjustment
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 63 Change the data so that thebrightness of the section A andthat of the section B is equal.
3 C 63 Subtract 8 from the data.
4 C 63 Press PAUSE button.
5 0 01 00 Set the data.
Fig. 5-1-20.
Fig. 5-1-21.
A
A
A
A
B
B
B
B
A
2H
5-38
DCR-TRV24E/TRV25E/TRV27E
6. White Balance Adjustment (PD-161 board)Correct the white balance.If deviated, the reproduction of the LCD screen may degenerate.
Mode VTR stop
Signal No signal
Measurement Point Check on LCD screen
Measuring Instrument
Adjustment Page C
Adjustment Address 67, 68
Specified Value The LCD screen should not be colored.
Note1: Check the white balance only when replacing the following parts.If necessary, adjust them.1. LCD panel2. Light induction plate3. IC5501
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 67 80 Set the data, and press PAUSEbutton.
3 C 68 80 Set the data, and press PAUSEbutton.
4 C 68 Check that the LCD screen is notcolored. If not colored, proceed tostep 10.
5 C 67 Change the data so that the LCDscreen is not colored.
6 C 67 Press PAUSE button.
7 C 68 Change the data so that the LCDscreen is not colored.
8 C 68 Press PAUSE button.
9 C 68 If the LCD screen is colored,repeat steps 5 to 9.
10 0 01 00 Set the data.
5-39
DCR-TRV24E/TRV25E/TRV27E
5-2. MECHANISM SECTIONADJUSTMENT
On the mechanism section adjustmentFor detail of mechanism section adjustments, checks, andreplacement of mechanism parts, refer to the separate volume “DVMECHANICAL ADJUSTMENT MANUAL J Mechanism ”.Note: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
2-1. HOW TO ENTER RECORD MODE WITHOUTCASSETTE
1) Connect the adjustment remote commander to the LANC jack.2) Turn the HOLD switch of the adjustment remote commander
to the ON position.3) Close the cassette compartment without the cassette.4) Select page: 3, address: 01, and set data: 0C, and press the
PAUSE button of the adjustment remote commander.(The mechanism enters the record mode automatically.)Note: The function buttons becomes inoperable.
5) To quit the record mode, select page: 3, address: 01, set data:00, and press the PAUSE button of the adjustment remotecommander. (Whenever you want to quit the record mode, besure to quit following this procedure.)
2-2. HOW TO ENTER PLAYBACK MODEWITHOUT CASSETTE
1) Connect the adjustment remote commander to the LANC jack.2) Turn the HOLD switch of the adjustment remote commander
to the ON position.3) Close the cassette compartment without the cassette.4) Select page: 3, address: 01, and set data: 0B, and press the
PAUSE button of the adjustment remote commander.(The mechanism enters the playback mode automatically.)Note: The function buttons becomes inoperable.
5) To quit the playback mode, select page: 3, address: 01, set data:00, and press the PAUSE button of the adjustment remotecommander. (Whenever you want to quit the playback mode,be sure to quit following this procedure.)
2-3. TAPE PATH ADJUSTMENT
1. Preparation for Adjustment
1) Clean the tape running side (tape guide, drum, capstan shaft,pinch roller, etc.).
2) Connect the adjustment remote commander to the LANC jack.3) Turn the HOLD switch of the adjustment remote commander
to the ON position.4) Connect an oscilloscope to VC-281 board CN1002 via the CPC-
8 jig (J-6082-388-A).Channel 1: VC-281 board, CN1002 Pin w; (Note)External trigger: VC-281 board, CN1002 Pin qjNote: Connect a 75Ω resistor between Pins w; of CN1002 and ql
(GND).5) Playback the alignment tape for tracking. (XH2-1)6) Select page: 3, address: 33, and set data: 08.7) Select page: 3, address: 26, and set data: 31.8) Check that the oscilloscope RF waveform is normal at the
entrance and exit.If not normal, adjust according to the separate volume“DV MECHANICAL ADJUSTMENT MANUAL J Mechanism ”.
CN1002 of VC-281 board
Table 5-2-1.
2. Processing after Completing Operations:1) Connect the adjustment remote commander to the LANC jack
and set the HOLD switch to the ON position.2) Select page: 3, address: 26, and set data: 00.3) Select page: 3, address: 33, and set data: 00.
CH1
Entrance side Exit sideCheck this section(Normal waveform)
CH2(Trigger)
3.3msec
Fig. 5-2-1.
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameLANC SIG
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
5-40
DCR-TRV24E/TRV25E/TRV27E
5-3. VIDEO SECTION ADJUSTMENTS
3-1. PREPARATIONS BEFORE ADJUSTMENTS
Use the following measuring instruments for video sectionadjustments.
3-1-1. Equipment Required
1) TV monitor2) Oscilloscope (dual-phenomenon, band above 30 MHz with
delay mode) (Unless specified otherwise, use a 10 : 1 probe.)3) Frequency counter4) Pattern generator with video output terminal.5) Digital voltmeter6) Audio generator7) Audio level meter8) Audio distortion meter9) Audio attenuator10) Regulated power supply11) Alignment tapes
• Tracking standard (XH2-1)Parts code: 8-967-997-01
• SW/OL standard (XH2-3)Parts code: 8-967-997-11
• Audio operation check for PAL (XH5-3P)Parts code: 8-967-997-55
• System operation check for PAL (XH5-5P)Parts code: 8-967-997-66
12) Adjustment remote commander (J-6082-053-B)13) CPC-8 jig (J-6082-388-A)14) Extension cable (100P, 0.5mm) (J-6082-352-A)
For extension between the VA-117 board (CN4002) and VC-281 board (CN1007).
5-41
DCR-TRV24E/TRV25E/TRV27E
3-1-2. Precautions on AdjustingNote1: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.1) The adjustments of this unit are performed in the VTR mode
or camera mode.To set to the VTR mode, set the power switch to “VCR” (or“PLAYER”) or set the “Forced VTR Power ON mode” usingthe adjustment remote commander (Note2).To set to the Camera mode, set the power switch to “CAMERA”or set the “Forced Camera Power ON mode” using theadjustment remote commander (Note3).After completing adjustments, be sure to exit the “Forced VTRPower ON Mode” or “Forced Camera Power ON Mode”.(Note5)
2) The front panel block ( Focus ring, Microphone unit., MA-409board, FB-219 board) need not be assembled. To remove it,disconnect the following connector.
VA-117 board CN4003 (24P, 0.5mm)3) Cabinet (R) (CK-108board, LCD block) need not be connected.
But removing the cabinet (R) (removing the VC-281 boardCN1005) means removing the lithium 3V power supply (CK-108 board, BT5201) , data such as date, time, user-set menuswill be lost. After completing adjustments, reset these data.But, the self-diagnosis data and the data on history of use (totaldrum rotation time etc.) will be kept even if the cabinet (R) hasbeen removed. (Refer to “5-4.Service Mode” for the data onthe history use and the self-diagnosis data.)To remove the cabinet (R), disconnect the following connectors.
VA-117 board CN4004 (12P, 0.5mm)VC-281 board CN1005 (28P, 0.5mm)
4) The EVF block (LB-077 board) is need not be connected. Toremove it, disconnect the following connector.
VA-117 board CN4201 (20P, 0.5mm)5) The intelligent accessory shoe is need not be connected. To
remove it, disconnect the following connector.VA-117 board CN4001 (20P, 0.5mm)
6) To open the VA-117 board, use the following extension cablebetween the VA-117 board CN4002 and VC-281 boardCN1007.
J-6082-352-A (100P, 0.5mm)7) The lens block (CD-366 board) is need not be connected. To
remove it, disconnect the following connectors.VC-281 board CN1501 (24P, 0.5mm)VC-281 board CN1301 (27P, 0.3mm)
8) By setting the “Forced VTR Power ON mode”, the video sectioncan be operate even if the control switch block (PS-CX2670)has been removed. When removing it, disconnect the followingconnector.
VC-281 board CN1008 (20P, 0.5mm)
Note2: Setting the “Forced VTR Power ON” mode (VTR mode)1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.The above procedure will enable the VTR power to be turnedon with the control switch block (PS-CX2670 block) removed.After completing adjustments, be sure to exit the “Forced PowerON mode”.
Note3: Setting the “Forced Camera Power ON” mode (Camera mode)1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.The above procedure will enable the camera power to be turnedon with the control switch block (PS-CX2670 block) removed.After completing adjustments, be sure to exit the “Forced PowerON mode”.
Note4: Setting the “Forced Memory Power ON” mode (Memory mode)1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjustment remote commander.The above procedure will enable the memory power to beturned on with the control switch block (PS-CX2670 block)removed.After completing adjustments, be sure to exit the “Forced PowerON mode”.
Note5: Exiting the “Forced Power ON” mode1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.3) Select page: 0, address: 01, and set data: 00.
5-42
DCR-TRV24E/TRV25E/TRV27E
3-1-3. Adjusting ConnectorsSome of the adjusting points of the video section are concentratedat VC-281 board CN1002. Connect the measuring instruments viathe CPC-8 jig (J-6082-388-A). The following table lists the pinnumbers and signal names of CN1002.
Table 5-3-1.
3-1-4. Connecting the EquipmentConnect the measuring instruments as shown in Fig. 5-3-2, andperform the adjustments.
Adjustmentremote
commander
LANC jack
Main unit
AUDIO/VIDEO jack
TV monitor
VIDEO(Yellow)
AUDIO L (White)
AUDIO R (Red)
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameLANC SIG
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
Fig. 5-3-2.
Fig. 5-3-1.
CN1002
1 2
19 20
Remove the CPC lid.
Color bar signal waveform Color bar patternColor bar signal waveform Color bar pattern
5-43
DCR-TRV24E/TRV25E/TRV27E
3-1-5. Alignment TapesUse the alignment tapes shown in the following table.Use tapes specified in the signal column of each adjustment.
Fig. 5-3-3 shows the 75% color bar signals recorded on the alignmenttape for Audio Operation Check.
Note: Measure with video terminal (Terminated at 75 Ω)
UseTape path adjustment
Switching position adjustment
Audio system adjustment
Operation check
NameTracking standard (XH2-1)
SW/OL standard (XH2-3)
Audio operation check(XH5-3P)
System operation check(XH5-5P)
Fig. 5-3-3. Color bar signal of alignment tapes
3-1-6. Input/Output Level and ImpedanceVideo input/output
Special stereo mini jackVideo signal: 1 Vp-p, 75 Ω unbalanced,
sync negativeS video input/output
4-pin mini DINLuminance signal: 1 Vp-p, 75 Ω unbalanced,
sync negativeChrominance signal: 0.300 Vp-p, 75 Ω unbalanced
Audio input/outputSpecial stereo mini jackInput level: 327mVInput impedance: More than 47kΩOutput level: 327 mV (at load impedance 47 kΩ)Output impedance: Below 2.2 kΩ
Color bar signal waveform Color bar pattern
1V0.7V
0.3V
White (100%)
Yello
w
Cya
nG
reen
Mag
enta
Red
Blu
e
Burst signalHorizontal sync signal
0.3V(100%)
Yello
w
Cya
n
Gre
en
Mag
enta
Red
Blu
e
Whi
te
Bla
ck
5-44
DCR-TRV24E/TRV25E/TRV27E
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT
1. Initialization of 8, A, B, C, D, E, F, 1B, 1E, 1F Page DataIf the 8, A, B, C, D, E, F, 1B, 1E, 1F page data is erased due to somereason, perform “1-2. INITIALIZATION OF 8, A, B, C, D, E, F,1B, 1E, 1F PAGE DATA” of “5-1. CAMERA SECTIONADJUSTMENT”.Note: When reading or writing the 1B, 1E, 1F page data, select page: 0,
address: 10, and set data: 01, then select B, E or F page. The 1B,1E or 1F page can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
2. Serial No. InputNote: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
2-1. Company ID InputWrite the company ID in the EEPROM (nonvolatile memory).
Page 8
Address 8C, 8D, 8E, 8F, 90
Input method:1) Select page: 0, address: 01, and set data: 01.2) Input the following data to page: 8, addresses: 8C to 90.
Note: Press the PAUSE button of the adjustment remote commandereach time to set the data.
3) Select page: 0, address: 01, and set data: 00.
2-2. Serial No. InputWrite the serial No. and model code in the EEPROM (nonvolatilememory). Convert the serial No. on the name plate from decimal tohexadecimal, and write in the EEPROM.
Page 8
Address 91, 92, 93
Input method:1) Select page: 0, address: 01, and set data: 01.2) Read the serial No. on the name plate, and take it as D1.
Example: If the serial No. is 77881.D1 = 77881
Note: Use six digits of the low rank when a serial No. is more thanseven digits.
3) Obtain D2 and H1 corresponding to D1 from Table 5-3-1.Example: If D1 is “77881”.
D2 = D1 – 65536 = 12345H1 = FE
Address8C
8D
8E
8F
90
Data08
00
46
01
02
D1 (Decimal)
000001 to 065535
065536 to 131071
131072 to 196607
D2 (Decimal)
D1
D1–65536
D1–131072
H1 (Hexadecimal)(Service model code)FE
FE
FE
Table 5-3-2.
4) Input H1 to page: 8, address: 91. (Model code input)Example: If H1 is “FE”.
Select page: 8, address: 91, set data: FE, andpress the PAUSE button.
5) Obtain the maximum decimal not exceeding D2 from Table 5-3-2, and take this as D3.
Example: If D2 is “12345”.D3 = 12288
6) Obtain the hexadecimal corresponding to D3 from Table 5-3-2, and take this as H3.
Example: If D3 is “12288”.H3 = 3000
7) Obtain the difference D4 between D2 and D3. (Decimalcalculation, 0 D4 255)
D4 = D2 – D3
Example: If D2 is “12345” and D3 is “12288”.D4 = 12345 – 12288 = 57
8) Convert D4 to hexadecimal, and take this as H4.(Refer to “Hexadecimal-decimal conversion table” in “5-4.Service Mode”.)
Example: If D4 is “57”.H4 = 39
9) Input the upper 2 digits of H3 to page: 8, address: 92.Example: If H3 is “3000”.
Select page: 8, address: 92, set data: 30, andpress the PAUSE button.
10) Input H4 to page: 8, address: 93.Example: If H4 is “39”.
Select page: 8, address: 93, set data: 39, andpress the PAUSE button.
11) Select page: 0, address: 01, and set data: 00.
5-45
DCR-TRV24E/TRV25E/TRV27E
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
0
256
512
768
1024
1280
1536
1792
2048
2304
2560
2816
3072
3328
3584
3840
4096
4352
4608
4864
5120
5376
5632
5888
6144
6400
6656
6912
7168
7424
7680
7936
8192
8448
8704
8960
9216
9472
9728
9984
10240
10496
10752
11008
11264
11520
11776
12032
12288
12544
12800
13056
13312
13568
13824
14080
14336
14592
14848
15104
15360
15616
15872
16128
16384
16640
16896
17152
17408
17664
17920
18176
18432
18688
18944
19200
19456
19712
19968
20224
20480
20736
20992
21248
21504
21760
22016
22272
22528
22784
23040
23296
23552
23808
24064
24320
24576
24832
25088
25344
25600
25856
26112
26368
26624
26880
27136
27392
27648
27904
28160
28416
28672
28928
29184
29440
29696
29952
30208
30464
30720
30976
31232
31488
31744
32000
32256
32512
32768
33024
33280
33536
33792
34048
34304
34560
34816
35072
35328
35584
35840
36096
36352
36608
36864
37120
37376
37632
37888
38144
38400
38656
38912
39168
39424
39680
39936
40192
40448
40704
40960
41216
41472
41728
41984
42240
42496
42752
43008
43264
43520
43776
44032
44288
44544
44800
45056
45312
45568
45824
46080
46336
46592
46848
47104
47360
47616
47872
48128
48384
48640
48896
49152
49408
49664
49920
50176
50432
50688
50944
51200
51456
51712
51968
52224
52480
52736
52992
53248
53504
53760
54016
54272
54528
54784
55040
55296
55552
55808
56064
56320
56576
56832
57088
57344
57600
57856
58112
58368
58624
58880
59136
59392
59648
59904
60160
60416
60672
60928
61184
61440
61696
61952
62208
62464
62720
62976
63232
63488
63744
64000
64256
64512
64768
65024
65280
0000
0100
0200
0300
0400
0500
0600
0700
0800
0900
0A00
0B00
0C00
0D00
0E00
0F00
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
1A00
1B00
1C00
1D00
1E00
1F00
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
2A00
2B00
2C00
2D00
2E00
2F00
3000
3100
3200
3300
3400
3500
3600
3700
3800
3900
3A00
3B00
3C00
3D00
3E00
3F00
4000
4100
4200
4300
4400
4500
4600
4700
4800
4900
4A00
4B00
4C00
4D00
4E00
4F00
5000
5100
5200
5300
5400
5500
5600
5700
5800
5900
5A00
5B00
5C00
5D00
5E00
5F00
6000
6100
6200
6300
6400
6500
6600
6700
6800
6900
6A00
6B00
6C00
6D00
6E00
6F00
7000
7100
7200
7300
7400
7500
7600
7700
7800
7900
7A00
7B00
7C00
7D00
7E00
7F00
8000
8100
8200
8300
8400
8500
8600
8700
8800
8900
8A00
8B00
8C00
8D00
8E00
8F00
9000
9100
9200
9300
9400
9500
9600
9700
9800
9900
9A00
9B00
9C00
9D00
9E00
9F00
A000
A100
A200
A300
A400
A500
A600
A700
A800
A900
AA00
AB00
AC00
AD00
AE00
AF00
B000
B100
B200
B300
B400
B500
B600
B700
B800
B900
BA00
BB00
BC00
BD00
BE00
BF00
C000
C100
C200
C300
C400
C500
C600
C700
C800
C900
CA00
CB00
CC00
CD00
CE00
CF00
D000
D100
D200
D300
D400
D500
D600
D700
D800
D900
DA00
DB00
DC00
DD00
DE00
DF00
E000
E100
E200
E300
E400
E500
E600
E700
E800
E900
EA00
EB00
EC00
ED00
EE00
EF00
F000
F100
F200
F300
F400
F500
F600
F700
F800
F900
FA00
FB00
FC00
FD00
FE00
FF00
Table 5-3-3.
5-46
DCR-TRV24E/TRV25E/TRV27E
3-3. SERVO AND RF SYSTEM ADJUSTMENTBefore perform the servo and RF system adjustments, check thatthe specified value of “54 MHz Origin Oscillation Adjustment” of“CAMERA SYSTEM ADJUSTMENT” is satisfied.And check that the data of page: 0, address: 10 is “00”. If not, setdata: 00 to this address.
Adjusting Procedure:1. CAP FG duty adjustment2. PLL f0 & LPF f0 adjustment3. Switching position adjustment4. AGC center level and APC & AEQ adjustment5. PLL f0 & LPF f0 fine adjustment
1. Cap FG Duty Adjustment (VC-281 board)Set the Cap FG signal duty cycle to 50% to establish an appropriatecapstan servo. If deviated, the uneven rotation of capstan and noisecan occur.
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 16
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 Close the cassette compartmentwithout inserting a cassette.
2 0 01 01 Set the data.
3 3 01 1B Set the data, and press PAUSEbutton.
4 3 02 Check that the data changes inthe following order.“1B” t “2B” t “00”
5 3 03 Check that the data is “00”.(Note2)
6 0 01 00 Set the data.
Note2: If the data is “01”, adjustment has errors or the mechanism deck isdefective.
2. PLL f0 & LPF f0 Adjustment (VC-281 board)
Mode VTR stop
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 1F, 20, 22, 29
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 21 DC Set the data, and press PAUSEbutton.
3 3 01 30 Set the data, and press PAUSEbutton.
4 3 02 Check that the data changes to“00” with in 5 sec. (Note2)
5 3 03 Check that the data is “00”.(Note2)
6 0 01 00 Set the data.
Note2: If it isn’t satisfied, select page: C, address: 21, set the followingdata, and press the PAUSE button, and repeat steps 3 to 5.
There are errors when it isn’t satisfied even if the above treatmentis done.If bit2, bit3, bit4, bit5 or bit 6 of the data of page: 3, address: 03 is“1”, there are errors. For the error contents, see the following table.(For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bitvalue discrimination”.)
Setting dataE0
D8
E4
D4
When the data of page: C, address: 21 is “DC”.
When the data of page: C, address: 21 is “E0”.
When the data of page: C, address: 21 is “D8”.
When the data of page: C, address: 21 is “E4”
Bit value of page: 3,address: 03 databit 2 = 1 or bit 3 = 1
bit 4 = 1 or bit 5 = 1
bit 6 = 1
Error contents
PLL f0 fine adjustment is defective
PLL f0 adjustment is defective
LPF f0 is defective
5-47
DCR-TRV24E/TRV25E/TRV27E
3. Switching Position Adjustment (VC-281 board)To obtain normal playback waveform output during the Digital8playback mode, adjust the switching position.
Mode VTR playback
Signal SW/OL reference tape (XH2-3)
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 10, 11, 12, 13
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 Insert the SW/OL reference tapeand enter the VTR STOP mode.
2 0 01 01 Set the data.
3 C 10 EE Set the data, and press PAUSEbutton.
4 3 21 Check that the data is “02”.(Note2)
5 3 01 0D Set the data, and press PAUSEbutton.
6 02 Check that the data changes to“00”.
7 3 03 Check that the data is “00”.(Note3)
8 0 01 00 Set the data.
Note2: If the data of page: 3, address: 21 is “72”, the tape top being played.After playing the tape for 1 to 2 seconds, stop it, perform step 5and higher.If the data of page: 3, address: 21 is “62”, the tape end being played.After rewinding the tape, perform step 5 and higher.
Note3: If bit 0 of the data is “1”, the EVEN channel is defective. If bit 1 is“1”, the ODD channel is defective. Contents of the defect is writteninto page: C, addresses: 10 and 12. See the following table. (Forthe bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit valuediscrimination”.) If bit 3 of the data is “1”, the tape end beingplayed, so rewind the tape and perform the adjustment again.
When the EVEN channel is defective
When the ODD channel is defective
Data of page: C,address: 10EE
E8
E7
Contents of defect
Writing into EEPROM (IC2502) is defective
Adjustment data is out of range
No data is returned from IC2101
Data of page: C,address: 12EE
E8
E7
Contents of defect
Writing into EEPROM (IC2502) is defective
Adjustment data is out of range
No data is returned from IC2101
4. AGC Center Level and APC & AEQ AdjustmentNote: The data of page: 0, address: 10 must be “00”.
4-1. Preparations before adjustments
Mode Camera recording
Subject Arbitrary
Adjusting method:
Order Page Address Data Procedure
1 7 30 80 Set the data.
2 Record the camera signal forthree minutes.
4-2. AGC Center Level Adjustment (VC-281 board)
Mode Playback
Signal Recorded signal at “Preparationsbefore adjustments”
Measurement Point Pin w; of CN1002 (RF MON) (Note1)Ext. trigger: Pin qj of CN1002 (SWP)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 1E
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) ofCN1002.75Ω resistor (Parts code: 1-247-804-11)
Adjusting method:
Order Page Address Data Procedure
1 Playback the recorded signal at“Preparations before adjustments”
2 0 01 01 Set the data.
3 3 33 08 Set the data.
4 Confirm that the playback RFsignal is stable. (Fig. 5-3-4.)
5 3 01 23 Set the data, and press PAUSEbutton.
6 3 02 Check that the data is “00”.
7 3 03 Check that the data is “00”.(Note2)
8 Perform “APC & AEQAdjustment”.
Note2: If the data of page: 3, address: 03 is other than “00”, adjustmenthas errors. (Take an appropriate remedial measures according tothe errors referring to the following table.)
Data Contents of defect
20 Perform re-adjustment. (Note 3)
30 The machine is defective
40 Perform re-adjustment. (Note 3)
50 The machine is defective
Note3: If this data is displayed twice successively, the machine is defective.
5-48
DCR-TRV24E/TRV25E/TRV27E
4-3. APC & AEQ Adjustment (VC-281 board)
Mode Playback
Signal Recorded signal at “Preparationsbefore adjustments”
Measurement Point Pin w; of CN1002 (RF MON) (Note1)Ext. trigger: Pin qj of CN1002 (SWP)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 18, 19, 1B, 1C, 21, 2C
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) ofCN1002.
75Ω resistor (Parts code: 1-247-804-11)Note2: The “AGC Center Level Adjustment” must have already been
completed before starting this adjustment.
Adjusting method:
Order Page Address Data Procedure
1 Playback the recorded signal at“Preparations before adjustments”
2 0 01 01 Set the data.
3 3 33 08 Set the data.
4 Confirm that the playback RFsignal is stable. (Fig. 5-3-4.)
5 3 01 07 Set the data, and press PAUSEbutton.
6 3 02 Check that the data changes from“07” to “00” in about 20 secondsafter pressing PAUSE button.
7 3 03 Check that the data is “00”.(Note3)
8 Perform “Processing afterCompleting Adjustments”.
Note3: If the data is other than “00”, adjustment has errors. Take anappropriate remedial measures according to the errors referring tothe following table.
Data Contents of defect
20 Perform re-adjustment. (Note 4)
30 The machine is defective
50 Perform re-adjustment. (Note 4)
60 The machine is defective
80 The machine is defective
Note4: If this data is displayed twice successively, the machine is defective.
4-4. Processing after Completing Adjustments
Order Page Address Data Procedure
1 7 30 00 Set the data.
2 3 33 00 Set the data.
3 0 01 00 Set the data.
6.7 msec
PB RF signal is stable
Pin qj
Pin w;
Fig. 5-3-4.
5-49
DCR-TRV24E/TRV25E/TRV27E
5. PLL f0 & LPF f0 Fine Adjustment (VC-281 board)
Mode VTR stop
Signal Arbitrary
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 1F, 20, 22, 29
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 01 30 Set the data, and press PAUSEbutton.
3 3 02 Check that the data changes to“00” with in 5 sec. (Note2)
4 3 03 Check that the data is “00”.(Note3)
5 0 01 00 Set the data.
Note2: If it isn’t satisfied, there are errors.Note3: If the data of page: 3, address: 03 is other than “00”, there are
errors. For the error contents, see the following table. (For the bitvalues, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit valuediscrimination”.)
Bit value of page: 3,address: 03bit 2 = 1 or bit 3 = 1
bit 4 = 1 or bit 5 = 1
bit 6 = 1
Error contents
PLL f0 fine adjustment is defective
PLL f0 adjustment is defective
LPF f0 is defective
5-50
DCR-TRV24E/TRV25E/TRV27E
3-4. VIDEO SYSTEM ADJUSTMENTSNote: Before perform the video system adjustments, check that the
specified value of “54 MHz Origin Oscillation Adjustment” of“CAMERA SYSTEM ADJUSTMENT” is satisfied.And check that the data of page: 0, address: 10 is “00”. If not, setdata: 00 to this address.
1. Chroma BPF f0 Adjustment (VA-117 board)Set the center frequency of IC4101 chroma band-pass filter.
Mode Camera
Subject Arbitrary
Measurement Point CH1: Chroma signal terminal of SVIDEO jack (75Ω terminated)CH2: Y signal terminal of S VIDEO jack(75Ω terminated)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 28
Specified Value A = 100mVp-p or lessB = 200mVp-p or more
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 Check that the burst signal (B) isoutput to the chroma signalterminal of S VIDEO jack.
3 3 0C 04 Set the data, and press PAUSEbutton.
4 C 28 Change the data for minimumamplitude of the burst signallevel (A).(The data should be “00” to “0F”.)
5 C 28 Press PAUSE button.
6 3 0C 00 Set the data, and press PAUSEbutton.
7 Check that the burst signal level(B) satisfies the specified value.
8 0 01 00 Set the data.
2. S VIDEO OUT Y Level Adjustment (VC-281 board)
Mode Camera
Subject Arbitrary
Measurement Point Y signal terminal of S VIDEO jack(75Ω terminated)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 25
Specified Value A = 1000 ± 14mV
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:DEMO MODE (Menu setting) ................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 0C 02 Set the data, and press PAUSEbutton.
3 C 25 Change the data and set the Ysignal level (A) to the specifiedvalue.
4 C 25 Press PAUSE button.
5 3 0C 00 Set the data, and press PAUSEbutton.
6 0 01 00 Set the data.
CH1
CH2
A
H
CH1
H
B
When the data of page: 3, address: 0C, is 04:
When the data of page: 3, address: 0C, is 00:
Fig. 5-3-5.
H
Center of luminance line
A
Fig. 5-3-6.
5-51
DCR-TRV24E/TRV25E/TRV27E
3. S VIDEO OUT Chroma Level Adjustment(VC-281 board)
Mode Camera
Subject Arbitrary
Measurement Point Chroma signal terminal of S VIDEOjack (75Ω terminated)External trigger: Y signal terminal ofS VIDEO jack
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 26, 27
Specified Value Cr level: A = 700 ± 14mVCb level:B = 700 ± 14mVBurst level: C = 300 ± 6mV
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:DEMO MODE (Menu setting) ................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 0C 02 Set the data, and press PAUSEbutton.
3 C 26 Change the data and set the Crsignal level (A) to the specifiedvalue.
4 C 26 Press PAUSE button.
5 C 27 Change the data and set the Cbsignal level (B) to the specifiedvalue.
6 C 27 Press PAUSE button.
7 Check that the burst signal level(C) is satisfied the specified value.
8 3 0C 00 Set the data, and press PAUSEbutton.
9 0 01 00 Set the data.
4. VIDEO OUT Y, Chroma Level Check (VC-281 board)
Mode Camera
Subject Arbitrary
Measurement Point Video terminal of AUDIO VIDEOjack (75Ω terminated)
Measuring Instrument Oscilloscope
Specified Value Sync level: A = 300 ± 18mVBurst level: B = 300 ± 18mV
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:DEMO MODE (Menu setting) ................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 3 0C 02 Set the data, and press PAUSEbutton.
2 Check that the sync signal level(A) satisfies the specified value.
3 Check that the burst signal level(B) satisfies the specified value.
4 3 0C 00 Set the data, and press PAUSEbutton.
H
C
A
0.23 µsec
B
0.23 µsec
H
B
A
Fig. 5-3-7.
Fig. 5-3-8.
5-52
DCR-TRV24E/TRV25E/TRV27E
3-5. AUDIO SYSTEM ADJUSTMENTS
[Connection of Audio System Measuring Devices]Connect the audio system measuring devices as shown in Fig. 5-3-9.
Fig. 5-3-9.
Recording (Camera mode)
Audio oscillator
Attenuator
600 Ω Left
Right
Main unit
MIC
600 Ω: 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11)
Main unit
AUDIO/VIDEOOUT
Left (White)
Right 47k Ω
47k Ω
Video (Yellow)
TV monitor
Audio level meteror Distortion meter
47k Ω (1-249-437-11)
Playback
(Red)
5-53
DCR-TRV24E/TRV25E/TRV27E
1. Playback Level Check
Mode VTR playback
Signal Alignment tape:For audio operation check(XH5-3P)
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio level meter and frequencycounter
Specified Value 32 kHz mode: 1 kHz, +3.0 ± 2.0dBs48 kHz mode: 1 kHz, +3.0 ± 2.0dBs44.1 kHz mode:The 7.35kHz signal level during EMPOFF is +2.0 ± 2.0dBs.The 7.35kHz signal level during EMPON is –6 ± 2 dB from the signal levelduring EMP OFF.
Checking Method:1) Check that the playback signal level is the specified value.
2. Overall Level Characteristics Check
Mode Camera recording and playback
Signal 400Hz, –66 dBs signal: MIC jack leftand right
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio level meter
Specified Value –7.5 ± 3.0dBs
Checking Method:1) Input the 400Hz, –66dBs signal in the MIC jack.2) Record in the camera mode.3) Playback the recorded section.4) Check that the 400Hz signal level is the specified value.
3. Overall Distortion Check
Mode Camera recording and playback
Signal 400Hz, –66dBs signal: MIC jack leftand right
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio distortion meter
Specified Value Below 0.4%(200Hz to 6kHz BPF ON)
Checking Method:1) Input the 400Hz, –66dBs signal in the MIC jack.2) Record in the camera mode.3) Playback the recorded section.4) Check that the distortion is the specified value.
4. Overall Noise Level Check
Mode Camera recording and playback
Signal No signal: Insert a shorting plug in theMIC jack
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio level meter
Specified Value Below –45dBs(IHF-A filter ON, 20kHz LPF ON)
Checking Method:1) Insert a shorting plug in the MIC jack.2) Record in the camera mode.3) Playback the recorded section.4) Check that the noise level is the specified value.
5. Overall Separation Check
Mode Camera recording and playback
Signal 400Hz, –66dBs signal: MIC jack<right> [left](Connect the MIC jack <left> [right]to GND)
Measurement Point Audio <left> [right] terminal ofAUDIO VIDEO jack
Measuring Instrument Audio level meter
Specified Value Below –40dBs (IHF-A filter ON)
< > : Left channel check[ ] : Right channel check
Checking Method:1) Input the 400Hz, –66dBs signal in the <right> [left] terminal
of the MIC jack only.2) Record in the camera mode.3) Playback the recorded section.4) Check that the signal level of the audio <left> [right] terminal
is the specified value.
5-54
DCR-TRV24E/TRV25E/TRV27E
5-4. SERVICE MODE
4-1. ADJUSTMENT REMOTE COMMANDERThe adjustment remote commander is used for changing thecalculation coefficient in signal processing, EVR data, etc. Theadjustment remote commander performs bi-directionalcommunication with the unit using the remote commander signalline (LANC). The resultant data of this bi-directional communicationis written in the non-volatile memory.
1. Using the adjustment remote commander1) Connect the adjustment remote commander to the LANC
terminal.2) Set the HOLD switch of the adjustment remote commander to
“HOLD” (SERVICE position). If it has been properlyconnected, the LCD on the adjustment remote commander willdisplay as shown in Fig. 5-4-1.
Fig. 5-4-1
3) Operate the adjustment remote commander as follows.• Changing the page
The page increases when the EDIT SEARCH+ button is pressed,and decreases when the EDIT SEARCH– button is pressed.There are altogether 19 pages, from 0 to F, 1B, 1E, 1F. (Note)
• Changing the addressThe address increases when the FF (M) button is pressed,and decreases when the REW (m) button is pressed. Thereare altogether 256 addresses, from 00 to FF.
• Changing the data (Data setting)The data increases when the PLAY (N) button is pressed,and decreases when the STOP (x) button is pressed. Thereare altogether 256 data, from 00 to FF.
• Writing the adjustment dataThe PAUSE button must be pressed to write the adjustmentdata (8, A, B, C, D, E, F, 1B, 1E, 1F page) in the nonvolatilememory. (The new adjusting data will not be recorded in thenonvolatile memory if this step is not performed.)
4) After completing all adjustments, turn off the main powersupply once.
Note: When reading or writing the 1B, 1E, 1F page data, select page:0, address: 10, and set data: 01, then select B, E or F page. The1B, 1E or 1F page can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10to “00”.
HexadecimalnotationLCD DisplayDecimal notationconversion value
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 A b c d E F
0 1 2 3 4 5 6 7 8 9 101112131415
2. Precautions upon usingthe adjustment remote commander
Mishandling of the adjustment remote commander may erase thecorrect adjustment data at times. To prevent this, it is recommendedthat all adjustment data be noted down before beginning adjustmentsand new adjustment data after each adjustment.
Page Data Address
5-55
DCR-TRV24E/TRV25E/TRV27E
4-2. DATA PROCESSThe calculation of the DDS display and the adjustment remotecommander display data (hexadecimal notation) are required forobtaining the adjustment data of some adjustment items. In this case,after converting the hexadecimal notation to decimal notation,calculate and convert the result to hexadecimal notation, and use itas the adjustment data. Indicates the hexadecimal-decimalconversion table.
Hexadecimal-decimal Conversion TableLower digit ofhexadecimal
Upper digit of hexadecimal
0 1 2 3 4 5 6 7 8 9 A(A)
B(b)
C(c)
D(d)
E(E)
F(F)
0
1
2
3
4
5
6
7
8
9
A (A)
B (b)
C (c)
D (d)
E (E)
F (F)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111
112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143
144 145 146 147 148 149 150 151 152 153 154 155 156 157 158
174
159
175160 161 162 163 164 165 166 167 168 169 170 171 172 173
177176 178 179 180 181 182 183 184 185 186 187 188 189 190 191
192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207
208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239
240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255
0
1
Note : The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander.(Example) If the DDS display or the adjustment remote commander shows BD (bd);
Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number.
0
2
Table. 5-4-1.
5-56
DCR-TRV24E/TRV25E/TRV27E
4-3. SERVICE MODE
Note: Before performing the adjustments, check the data of page: 0,address: 10 is “00”. If not, set data: 00 to this address.
1. Setting the Test Mode
Page D Address 10
• Before setting the data , select page: 0, address: 01, and set data:01.
• For page D, the data set is recorded in the non-volatile memoryby pressing the PAUSE button of the adjustment remotecommander. In this case, take note that the test mode will not beexited even when the main power is turned off.
• After completing adjustments/repairs, be sure to return the dataof this address to 00, and press the PAUSE button of the adjustmentremote commander.Select page: 0, address: 01, and set data: 00.
2. Emergence Memory Address
Page C Address F4 to FF
When no error occurs in this unit, data “00” is written in the aboveaddresses (F4 to FF). when first error occurs in the unit, the datacorresponding to the error is written in the first emergency address(F4 to F7). In the same way, when the second error occurs, the datacorresponding to the error is written in the second emergency address(F8 to FB). Finally, when the last error occurs, the data correspondingto the error is written in the last emergency address (FC to FF).
Note: After completing adjustments, be sure to initialize the data ofaddresses F4 to FF to “00”.
Initializing method:1) Select page: 0, address: 01, and set data: 01.2) Select page: 3, address: 01, set data: 37, and press the PAUSE
button.3) Select page: 0, address: 01, and set data: 00.
ContentsEMG code when first error occurs
Upper: MSW code when shift starts when firsterror occursLower: MSW code when first error occurs
Lower: MSW code to be moved when first erroroccurs
EMG code when second error occurs
Upper: MSW code when shift starts when seconderror occursLower: MSW code when second error occurs
Lower: MSW code to be moved when second erroroccurs
EMG code when last error occurs
Upper: MSW code when shift starts when last erroroccursLower: MSW code when last error occurs
Lower: MSW code to be moved when last erroroccurs
AddressF4
F6
F7
F8
FA
FB
FC
FE
FF
2-1. EMG Code (Emergency Code)Codes corresponding to the errors which occur are written inaddresses F4, F8 and FC. The type of error indicated by the codeare shown in the following table.
Emergency TypeNo error
Loading motor emergency during loading
Loading motor emergency during unloading
T reel emergency during normal rotation
S reel emergency during normal rotation
T reel emergency (Short circuit between S reelterminal and T reel terminal)
FG emergency at the start up of the capstan
FG emergency at the start up of the drum
FG emergency during normal rotation of the drum
Code00
10
11
22
23
24
30
40
42
FunctionNormal
Forced camera power ON
Forced VTR power ON
Forced camera + VTR power ON
Forced memory power ON
Data00
01
02
03
05
5-57
DCR-TRV24E/TRV25E/TRV27E
00
10
=2
11
10
=E
← UNLOAD
Lock releasedCassette compartment
Pinch roller pressing
LS chassis movement section
EJ BL
10
10
=A
11
10
=E
ULE BL
10
00
=8
11
10
=E
SR BL
11
00
=C
11
10
=E
GL BL
01
00
=4
11
10
=E
STOP BL
01
10
=6
R/P
LOAD →
← A (MSB) ← B← C← D (LSB) (Fixed at “0”)
Mechanical Position
Position
EJ
BL
ULE
SR
GL
STOP
R/P
NULL
Code
2
E
A
8
C
4
6
0
F
ContentsPosition at which the cassette component lock is released, at the farthest unload side mechanicallyat which the mechanism can move no further in the UNLOAD direction.
BLANK code, at the boundary between codes.
EJECT completion position. when the cassette is ejected, the mechanism will stop at this position.Cassette IN standby. The guide will start protruding out as the mechanism moves towards theLOAD position.
Position at which it is possible to release the S ratchet.
Guide loading are performed here.
Stop position in the loading state. The pinch roller separates, the tension regulator returns, and thebrake is imposed on both reels.
PB, REC, CUE, REVIEW, PAUSE positions. When pinch roller is pressed, and the tensionregulator is ON, the mechanism is operating at this position in modes in which normal images areshown.
Code not existing in the MD. Default value.
Status before finding any mechanism position.
2-2. MSW CodeMSW when errors occur:Information on MSW (mode SW) when errors occurMSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)MSW of target of movement: Information on target MSW of movement when the mechanism position is moved
5-58
DCR-TRV24E/TRV25E/TRV27E
Display on theadjustment
remotecommander
0
1
2
3
4
5
6
7
8
9
A (A)
B (b)
C (c)
D (d)
E (E)
F (F)
Bit valuesbit3or
bit70
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
bit2or
bit60
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
bit1or
bit50
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
bit0or
bit40
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1B
Example: If “8E” is displayed on the adjustment remote commander, thebit values for bit7 to bit4 are shown in the A column, and thebit values for bit3 to bit0 are shown in the B column.
Page
Address
bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the adjustment remote commander
3. Bit value discriminationBit values must be discriminated using the display data of theadjustment remote commander for following items. Use the tablebelow to discriminate if the bit value is “1” or “0”.
A
4. Switch check (1)
Page 7 Address 0E
Note: The data of page: 0, address: 10 must be “00”.
Bit1
2
3
FunctionMIC jack (MA-409 board J5901)
AUDIO/VIDEO jack (JK-217 board J5302)
S VIDEO jack (JK-217 board J5302)
When bit value=1Used
Used
Used
When bit value=0Not used
Not used
Not used
Bit0
1
2
3
4
5
6
7
FunctionPOWER SW (VTR MODE SW) (PS-CX2670 block S001)
POWER SW (CAM MODE SW) (PS-CX2670 block S001)
START/STOP SW (PS-CX2670 block S002)
EJECT SW (FP-443 flexible S201)
CC DOWN SW (Mechanism chassis)
PHOTO FREEZE SW (PS-CX2670 block S071)
POWER SW (PHOTO STBY SW) (PS-CX2670 block S001)
When bit value=1ON (VCR/PLAYER)
ON (CAMERA)
ON
ON
ON (DOWN)
ON
ON (MEMORY)
When bit value=0OFF
OFF
OFF
OFF
OFF (UP)
OFF
OFF
Using method:1) Select page: 7, address: 0E.2) By discriminating the bit value of display data, the state of the switch can be discriminated.
5. Switch check (2)
Page 7 Address 0C
Note: The data of page: 0, address: 10 must be “00”.
Using method:1) Select page: 7, address: 0C.2) By discriminating the bit value of display data, the state of the switch can be discriminated.
5-59
DCR-TRV24E/TRV25E/TRV27E
6. Switch check (3)
Page 3 Address 61
Note: The data of page: 0, address: 10 must be “00”.
Using method:1) Select page: 3, address: 61.2) By discriminating the bit value of display data, the state of the switch can be discriminated.
Bit6
FunctionHEADPHONS jack (MA-409 board J5902)
When bit value=1Used
When bit value=0Not used
7. Switch check (4)
Page 2 Address 60 to 66
Note: The data of page: 0, address: 10 must be “00”.
Using method:1) Select page: 2, address: 60 to 66.2) By discriminating the display data, the pressed key can be discriminated.
Address
60(KEY AD0)(IC3101 tl)
61(KEY AD1)(IC3101 y;)
62(KEY AD2)(IC3101 ya)
63(KEY AD3)(IC3101 yg)
64(KEY AD4)(IC3101 yh)
65(KEY AD5)(IC3101 yj)
66(KEY AD6)(IC3101 yk)
00(00 to 0C)
PHOTO(PHOTO REC)(PS-CX2670)
(S071)
MPEG PLAY(SH-CX2670)
(S101)
PB ZOOM(SH-CX2670)
(S114)
REC(SH-CX2670)(S106,111)*1
STOP(CK-108)(S5201)
COLOR SLOWS/ SUPER NS
(JK-218)(S5351)
FADER(FP-444)(S301)
19(0D to 24)
EDITSEARCH +(FP-443)(S202)
MEMORYPLAY
(SH-CX2670)(S102)
MENU(SH-CX2670)
(S115)
VOL +(SH-CX2670)
(S110)
REW(CK-108)(S5202)
FOCUS(INFINITY)
(FP-444)(S302)
Data32
(25 to 3F)EDIT
SEARCH –(FP-443)(S203)
MEMORYINDEX
(SH-CX2670)(S107)
AUDIO DUB(SH-CX2670)
(S116)
END SEARCH(SH-CX2670)
(S109)
PLAY(CK-108)(S5204)
FOCUS(AUTO/MANUAL)
(FP-444)(S302)
4E(40 to 5D)
MEMORYDELETE
(SH-CX2670)(S112)
BACK LIGHT(KP-CX2670)
(S100)
DISPLAY(SH-CX2670)
(S104)
FF(CK-108)(S5205)
6F(5E to 81)
MEMORYMIX
(SH-CX2670)(S113)
EXPOSURE(KP-CX2670)
(S101)
VOL –(SH-CX2670)
(S105)
PAUSE(CK-108)(S5206)
96(82 to AA)
MEMORY +(SH-CX2670)
(S108)
PANELREVERSE(FP-309)
PANEL CLOSE(CK-108)(S5207)
EXECUTE(KP-CX2670)
(S103)
C1(AB to D7)
MEMORY –(SH-CX2670)
(S103)
E8(D8 to FF)
No key input
No key input
PANELNORMAL(FP-309)
PANEL OPEN(CK-108)(S5207)
No key input
No key input
No key input
*1: DCR-TRV25E/TRV27E
5-60E
DCR-TRV24E/TRV25E/TRV27E
8. Record of Use check (1)
Page 7 Address A7 to A9
Note1: When replacing the drum assembly or the mechanism deck, initialize the data of address: A7 to A9.Note2: This data will be kept even if the lithium battery (CK-108 board BT5201 of the cabinet (R) assembly) is removed.Note3: The data of page: 0, address: 10 must be “00”.
Using method:1) The record of use data is displayed at addresses: A7 to A9.
Initializing method:1) Select page: 7, address: 00, and set data: 71.2) Select page: 7, address: 01, set data: 71 and press the PAUSE button.3) Check that the data of page: 7, address: 02 is “00”.
AddressA7
A8
A9
Remarks100000th place digit and 10000th place digit of counted time
1000th place digit and 100th place digit of counted time
10th place digit and 1st place digit of counted time
FunctionHour (H)
Drum rotation counted time (BCD code) Hour (M)
Hour (L)
9. Record of Use check (2)
Page 7 Address C8 to CD
Note1: This data will be kept even if the lithium battery (CK-108 board BT5201 of the cabinet (R) assembly) is removed.Note2: The data of page: 0, address: 10 must be “00”.
Using method:1) The record of use data is displayed at addresses: C8 to CD.
10. Record of Self-diagnosis check
Page 7 Address B0 to C6
AddressC8
C9
CA
CB
CC
CD
Remarks
After setting the clock, set the date of power on next.
FunctionYear
User initial power on date (BCD code) Month
Day
Final condensation occurrence dateYear
(BCD code)Month
Day
Note1: This data will be kept even if the lithium battery (CK-108 boardBT5201 of the cabinet (R) assembly) is removed.
Note2: The data of page: 0, address: 10 must be “00”.
Address Self-diagnosis code
B0 “Repaired by” code (Occurred 1st time) *1
B1 “Block function” code (Occurred 1st time)
B2 “Detailed” code (Occurred 1st time)
B4 “Repaired by” code (Occurred 2nd time) *1
B5 “Block function” code (Occurred 2nd time)
B6 “Detailed” code (Occurred 2nd time)
B8 “Repaired by” code (Occurred 3rd time) *1
B9 “Block function” code (Occurred 3rd time)
BA “Detailed” code (Occurred 3rd time)
BC “Repaired by” code (Occurred 4th time) *1
BD “Block function” code (Occurred 4th time)
BE “Detailed” code (Occurred 4th time)
C0 “Repaired by” code (Occurred 5th time) *1
C1 “Block function” code (Occurred 5th time)
C2 “Detailed” code (Occurred 5th time)
C4 “Repaired by” code (Occurred the last time) *1
C5 “Block function” code (Occurred the last time)
C6 “Detailed” code (Occurred the last time)
*1 : “01” → “C”, “03” → “E”
Using method:1) The past self-diagnosis codes are displayed at addresses: BC
to C6. Refer to “SELF-DIAGNOSIS FUNCTION” for detailof the self-diagnosis code.
6-1
DCR-TRV24E/TRV25E/TRV27E
SECTION 6REPAIR PARTS LIST
6-1. EXPLODED VIEWSNOTE:• -XX, -X mean standardized parts, so they may
have some differences from the original one.• Items marked “*” are not stocked since they
are seldom required for routine service. Somedelay should be anticipated when ordering theseitems.
• The mechanical parts with no reference numberin the exploded views are not supplied.
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
COVERCOVER
6-1-1. OVERALL
Ref. No. Part No. Description Ref. No. Part No. Description
1 3-989-735-81 SCREW (M1.7), LOCK ACE, P22 X-3950-537-1 CAP ASSY, LENS3 4-974-725-01 SCREW (M1.7X2.5), P4 3-713-791-11 SCREW (M1.7X5), TAPPING, P25 3-067-024-01 BRACKET (LOWER), STRAP
6 X-3952-229-1 BT PANEL ASSY7 3-067-025-01 CPC LID8 X-3952-231-1 TOP CABINET ASSY9 3-073-852-01 VA HEAT SINK
10 3-073-851-01 VA RADIATION SHEET A11 1-684-248-11 FP-434 FLEXIBLE BOARD12 3-073-511-21 PLATE, JACK ORNAMENTAL (TRV24E)12 3-073-511-31 PLATE, JACK ORNAMENTAL (TRV25E/TRV27E)13 3-073-502-31 SHEET, POWER (TRV25E/TRV27E)
13 3-073-502-41 SHEET, POWER (TRV24E)14 3-074-433-01 LABEL, COLOR (VF)BT901 1-694-772-11 TERMINAL BOARD, BATTERY
VA-117
A
A
1
1
1
12
2
3
1
1
1
1
1
1
13
4
14
5
6
7
8
9
1011
3
3
3
BT901
F panel section(See page 6-2)
Main chassis complete section(See page 6-7)
Cabinet (R) section(See page 6-3)
EVF section(See page 6-6)
Cabinet (L) section(See page 6-8)
6-2
DCR-TRV24E/TRV25E/TRV27E
Ref. No. Part No. Description Ref. No. Part No. Description
51 4-974-725-01 SCREW (M1.7X2.5), P52 A-7078-104-A MA-409 BOARD, COMPLETE53 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P254 3-073-464-01 RETAINER, FOCUS BUTTON55 3-073-463-01 FOCUS, BUTTON
56 3-073-460-01 RETAINER (2), MICROPHONE57 3-073-461-01 CUSHION, MICROPHONE RETAINER58 3-073-459-01 RETAINER (1), MICROPHONE
59 3-074-585-01 CUSHION, MICROPHONE60 3-073-462-01 LIGHT, TALLY GUIDE61 A-7078-103-A FB-219 BOARD, COMPLETE62 X-3952-402-1 F PANEL ASSY (G)63 3-075-386-01 CUSHION, JACK
64 1-684-258-21 FP-444 FLEXIBLE BOARDMIC901 1-542-477-11 MICROPHONE
6-1-2. FRONT PANEL SECTION
A
A
MIC901
51
52
5354
64
55
5657
58
59
60
62
61
5353
63
63
53
6-3
DCR-TRV24E/TRV25E/TRV27E
Ref. No. Part No. Description Ref. No. Part No. Description
101 3-055-573-01 SCREW (M1.7), LOCK ACE, P2102 A-7078-105-A CK-108 BOARD, COMPLETE103 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2104 3-074-072-01 FRAME BOTTOM105 3-055-257-01 TRIPOD (LARGE)
106 3-073-466-01 BLIND, KURUPON107 1-477-147-11 SWITCH BLOCK, CONTROL (KP-CX2670)
* 108 X-3950-471-1 RETAINER ASSY, SPEAKER109 X-3952-407-1 CABINET (R) ASSY 2.5 (TRV24E/TRV25E)
109 X-3952-408-2 CABINET (R) ASSY 3.5 (TRV27E)110 3-959-978-02 CUSHION, PANEL111 1-477-149-21 SWITCH BLOCK, CONTROL (SH-CX2670)
(TRV25E/TRV27E)111 1-477-149-31 SWITCH BLOCK, CONTROL (SH-CX2670)
(TRV24E)112 3-074-538-01 RETAINER, P HARNESS
113 3-713-791-11 SCREW (M1.7X5), TAPPING, P2SP901 1-529-590-11 SPEAKER (2.0CM)
6-1-3. CABINET (R) SECTION
CK-108
B
A
B
A
SP901
ns
101
102103
104
105
106
113101
107
108
109110
103
103 112
111
: BT5201 (Lithium battery) CK-108 board on the mount position. (See page 4-82)
LCD section (2.5 inch) (See page 6-4)LCD section (3.5 inch)(See page 6-5)
ns : not supplied
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
6-4
DCR-TRV24E/TRV25E/TRV27E
Ref. No. Part No. Description Ref. No. Part No. Description
151 3-056-233-21 SCREW (M2), LOCK ACE, P2152 X-3952-405-1 P CABINET (C) ASSY 2.5153 4-974-725-01 SCREW (M1.7X2.5), P154 3-073-468-01 COVER (FRONT), HINGE155 X-3952-242-2 HINGE ASSY
156 1-684-256-21 FP-442 FLEXIBLE BOARD157 3-073-469-01 COVER (REAR), HINGE158 1-961-795-11 HARNESS (PV-138)159 3-073-488-71 PLATE, P ORNAMENTAL (TRV25E)159 3-073-488-81 PLATE, P ORNAMENTAL (TRV24E)
160 X-3952-244-1 P FRAME ASSY (2.5)161 3-073-474-01 P CABINET (M) 2.5162 3-073-470-01 BUTTON, P OPEN163 3-073-472-01 SPRING (U), LOCK164 3-073-471-01 P LOCK
165 3-073-473-01 SPRING (L), LOCK166 A-7078-106-A PD-161 (25SH123) BOARD, COMPLETE167 3-073-467-01 LCD HOLDERLCD901 1-803-853-21 INDICATOR MODULE LIQUID CRYSTALLCD902 A-7096-989-A INDICATION LCD BLOCK ASSY
0ND901 1-518-798-21 TUBE, FLUORESCENT,COLD CATHODE
6-1-4. LCD SECTION (2.5INCH) (TRV24E/TRV25E)
PD-161
A
B
LCD901
ND901
151
151
152
151
153
154
155
157
158166
167
159
LCD902
160
163 162
161
153
153156
164
165
A
B
ns(8P)
(20P)
ns : not supplied
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
6-5
DCR-TRV24E/TRV25E/TRV27E
Ref. No. Part No. Description Ref. No. Part No. Description
201 3-056-233-21 SCREW (M2), LOCK ACE, P2202 X-3952-406-2 P CABINET (C) ASSY 3.5203 4-974-725-01 SCREW (M1.7X2.5), P204 3-073-468-01 COVER (FRONT), HINGE205 X-3952-242-2 HINGE ASSY
206 1-684-256-21 FP-442 FLEXIBLE BOARD207 3-073-469-01 COVER (REAR), HINGE208 1-961-796-11 HARNESS (PV-139)209 3-073-488-51 PLATE, P ORNAMENTAL210 X-3952-289-1 P FRAME ASSY
211 3-073-850-01 P CABINET (M) 3.5212 3-073-470-01 BUTTON, P OPEN213 3-073-472-01 SPRING (U), LOCK214 3-073-471-01 P LOCK215 3-073-473-01 SPRING (L), LOCK
216 A-7012-227-A PD-161 (35SH123) BOARD, COMPLETE217 3-073-467-01 LCD HOLDER218 3-075-395-01 SHEET, P ELECTROSTATICLCD901 1-803-855-21 INDICATOR MODULE LIQUID CRYSTALLCD902 A-7096-989-A INDICATION LCD BLOCK ASSY
0ND901 1-517-855-31 TUBE, FLUORESCENT,COLD CATHODE
6-1-5. LCD SECTION (3.5INCH) (TRV27E)
PD-161
A
BLCD901
ND901
201
201
202
201
203
204
205
207
208216
217
209
LCD902
210
213
218
212
211
203
203206
214
215
A
B
ns(8P)
(20P)
ns : not supplied
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
6-6
DCR-TRV24E/TRV25E/TRV27E
251 4-974-725-01 SCREW (M1.7X2.5), P252 3-073-454-01 SHEET, VF FLEXIBLE BOARD RETAINER253 3-713-791-31 SCREW (M1.7X6), TAPPING, P2254 X-3952-234-1 VF BASE ASSY255 1-684-249-11 FP-435 FLEXIBLE BOARD
256 A-7078-102-A LB-077 BOARD, COMPLETE257 3-072-214-01 GUIDE (20), LAMP
258 3-072-211-01 ILLUMINATOR259 3-072-210-01 SHEET, PRISM260 X-3952-235-1 VF CABINET (UPPER) ASSY261 3-059-734-01 CUSHION (1), LCD262 X-3952-236-1 VF CABINET (LOWER) ASSY
263 X-3951-453-1 LENS ASSY, VFLCD903 8-753-028-47 LCX032AN-J
Ref. No. Part No. Description Ref. No. Part No. Description
6-1-6. EVF SECTION
252
255
256
257
258
259
261 262
260
263
253
254
251
LCD903
ns
253
ns
ns : not supplied
6-7
DCR-TRV24E/TRV25E/TRV27E
301 4-974-725-01 SCREW (M1.7X2.5), P302 A-7078-100-A JK-217 BOARD, COMPLETE303 A-7078-101-A JK-218 BOARD, COMPLETE304 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2305 3-073-845-01 FRAME (G), LENS
306 1-815-124-11 CONNECTOR, EXTERNAL (HOT SHOE)307 3-073-847-01 CD RADIATION SHEET308 3-073-846-01 CD HEAT SINK309 3-059-722-01 COVER, CASSETTE COMPARTMENT310 X-3952-290-1 MD FRAME ASSY (G)
311 3-059-718-01 SCREW (M1.4X1.5)312 1-684-250-11 FP-436 FLEXIBLE BOARD313 3-074-611-01 SHEET, HEAT INSULATING314 A-7078-287-A VC-281 BOARD, COMPLETE(SERVICE)
(TRV25E/TRV27E)314 A-7078-331-A VC-281 BOARD, COMPLETE(SERVICE)(TRV24E)
315 3-074-613-01 VV SHIELD SHEET316 A-7012-225-A VA-117 (GFB) BOARD, COMPLETE317 3-059-725-01 LABEL, LS318 1-684-254-11 FP-440 FLEXIBLE BOARD319 1-684-251-11 FP-437 FLEXIBLE BOARD
320 1-684-259-11 FP-445 FLEXIBLE BOARD321 3-713-791-41 SCREW (M1.7X5), TAPPING, P2322 A-7012-226-A CD-366 BOARD, COMPLETE323 3-053-973-01 RUBBER (W), SEAL324 1-758-569-11 FILTER BLOCK, OPTICAL
325 8-848-756-01 DEVICE, LENS LSV-750A326 3-074-612-01 CUSHION, SENSOR PROTECTION327 3-831-441-11 TAPE (F)328 3-074-614-01 SHEET, CD FLEXIBLE BOARD SHIELDIC5101 A-7031-359-A CCD BLOCK ASSY (CCD IMAGER)
Ref. No. Part No. Description Ref. No. Part No. Description
Be sure to read “Precautions upon replacing CCD imager”on page 4-9 when changing the CCD imager.
6-1-7. MAIN CHASSIS COMPLETE SECTION
VC-281
VA-117
301
301
301
301
301
301
301
301305
325327326
313
315
311
321
304
306317
310
312
309
303
308
307322
314
316
318
328
302
319
320
323324
IC5101
AB
C
D
A
B C
D
E
F
F
G
G
E
ns
nsMechanism deck(See page 6-9 to 6-11)
ns : not supplied
6-8
DCR-TRV24E/TRV25E/TRV27E
351 X-3952-237-1 LOCK ASSY, GRIP352 3-989-735-91 SCREW (M1.7), LOCK ACE, P2353 X-3952-416-1 CABINET (L) ASSY (G)354 3-713-791-11 SCREW (M1.7X5), TAPPING, P2355 3-074-586-01 CUSHION (2), MUFFLE
* 356 3-055-189-01 FOOT (A)357 3-061-550-01 BELT, GRIP358 3-073-686-01 SCREW (M2X2.5)359 X-3952-230-1 COVER ASSY, JACK360 3-073-456-01 EJECT KNOB
361 1-684-252-11 FP-438 FLEXIBLE BOARD362 1-477-148-11 SWITCH BLOCK, CONTROL (PS-CX2670)363 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2364 X-3952-238-1 CS FRAME ASSY365 1-816-271-11 CONNECTOR, MEMORY STICK 10P
366 3-073-457-01 COVER, GRIP367 4-974-725-01 SCREW (M1.7X2.5), P368 3-073-458-01 COVER, ZOOM369 3-073-928-01 L SHEET370 1-684-257-21 FP-443 FLEXIBLE BOARD
Ref. No. Part No. Description Ref. No. Part No. Description
6-1-8. CABINET (L) SECTION
A
B
B
A 351
352
352355353
354
356
357
358
359
354
354
354
366
368
370
369
367
354
360361
362
363
364
365
363
363
367
ns
ns
ns : not supplied
6-9
DCR-TRV24E/TRV25E/TRV27E
701 3-703-816-14 SCREW (M1.4)702 X-3952-017-3 CASSETTE COMPARTMENT ASSY703 3-059-082-01 SPRING, TENSION
(CASSETTE COMPARTMENT S)704 3-059-208-01 SPRING(CASSETTE COMPARTMENT T)705 X-3950-370-3 DAMPER ASSY
706 3-059-101-03 RETAINER, LS GUIDE707 7-624-102-04 STOP RING 1.5, TYPE -E
708 3-704-197-21 SCREW (M1.4X2.5), SPECIAL HEAD709 X-3950-364-1 GEAR ASSY, GOOSENECK710 X-3950-366-1 TABLE ASSY, T REEL711 3-075-097-01 SCREW (M1.4X1.4), SPECIAL HEAD712 3-059-093-01 RETAINER, LED
713 X-3950-361-1 PLATE ASSY, RETAINERM901 A-7048-940-A DRUM (DEH-18A-R)
Ref. No. Part No. Description Ref. No. Part No. Description
6-1-9. CASSETTE COMPARTMENT ASSEMBLY, DRUM BLOCK ASSEMBLY
703
704
M901
705
706701
708
701
707
701
702
708
710
709
713
711
711
712
LS chassis block assembly(See page 6-10)
Mechanism chassis block assembly(See page 6-11)
6-10
DCR-TRV24E/TRV25E/TRV27E
751 3-059-173-01 PLATE, LS CAM752 3-075-097-01 SCREW (M1.4X1.4), SPECIAL HEAD753 X-3950-371-1 ARM ASSY, BRAKE (S) DRIVING754 3-059-166-01 BRAKE (S)755 3-059-146-01 POSITIONING (S), CASSETTE
756 3-059-167-01 SPRING (BRAKE S), TENSION COIL757 3-059-169-01 SPRING (BRAKE S ARM), TORSION758 3-703-816-14 SCREW (M1.4)759 3-059-090-01 SCREW (M1.4X2.5), SPECIAL HEAD
* 760 X-3950-358-4 TG1 ASSY
761 3-059-156-01 SPRING (TENSION REGULATOR)762 X-3950-365-2 TABLE ASSY, S REEL763 A-7094-819-A TG7 BLOCK ASSY
764 3-059-165-01 SPRING (TG7 RETURN), TORSION765 X-3950-359-1 ARM ASSY , PINCH (O)766 3-059-161-01 SPRING (PINCH RETURN), TORSION767 3-059-170-01 BRAKE (T)768 3-059-171-01 GEAR (T), BRAKE
769 3-059-172-01 SPRING (T), BRAKE770 A-7094-816-B LS BLOCK ASSYD901 8-719-078-71 DIODE LN57A.SO (TAPE LED)H901 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (S REEL)H902 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (T REEL)
Q901 8-729-028-71 TRANSISTOR PN166.SO (TAPE END SENSOR)Q902 8-729-028-71 TRANSISTOR PN166.SO (TAPE TOP SENSOR)S903 1-572-288-11 SWITCH, PUSH (C.C.DOWN)
Ref. No. Part No. Description Ref. No. Part No. Description
6-1-10. LS CHASSIS BLOCK ASSEMBLY
753
754
755
756
757758
760759
761762
763
764765
766
D901
Q901
770
767
768769
S903
Q902H901
H902
nsns
ns
ns
752
751
FP-102
Note: FP-102 is included in the LS sub assy and is attached to chassis by hot-press. Because installation of FP-102 requires a very high accuracy, FP-102 is not supplied as an independent service parts.
Note
ns : not supplied
6-11
DCR-TRV24E/TRV25E/TRV27E
801 3-059-211-01 GEAR, CONVERSION802 3-059-220-01 GEAR, RELAY803 3-059-187-01 SHAFT, WORM804 3-059-186-02 HOLDER, MOTOR805 3-060-002-01 ROLLER, LS GUIDE
806 3-059-189-01 GEAR (A), CAM807 3-704-197-21 SCREW (M1.4X2.5), SPECIAL HEAD808 3-059-225-01 SHIELD, MOTOR809 3-059-191-01 ROLLER, LS810 3-059-190-01 ARM, LS
811 1-677-049-11 FP-228 FLEXIBLE BOARD (DEW SENOR)812 1-677-084-11 FP-100 FLEXIBLE BOARD813 3-059-148-01 ARM, TG1 DRIVING814 3-059-149-01 SLIDER, TG1 CAM815 3-703-816-14 SCREW (M1.4)
816 3-059-117-01 COVER (A), GEAR
817 X-3950-367-1 GEAR ASSY, MODE818 3-059-139-01 GEAR, GL DRIVING819 3-059-188-01 GEAR, DECELERATION820 A-7094-818-A COASTER (S) BLOCK ASSY821 A-7094-817-A COASTER (T) BLOCK ASSY
822 3-059-126-01 RAIL, GUIDE823 3-962-914-01 SCREW (M1.4X2)824 A-7094-822-A DRUM BASE BLOCK ASSY825 3-059-118-01 COVER (B), GEAR826 3-059-083-01 COVER (C), GEAR
827 X-3950-368-1 ARM ASSY, PINCH DRIVING828 3-059-192-01 GEAR (B), CAM829 3-063-355-01 ROLLER (S1), LS GUIDE830 3-065-202-01 SUPPORT, TG7M902 8-835-685-01 MOTOR, DC SCD18A/C-NP
(INCLUDING BELT)(CAPSTAN)
M903 A-7094-823-A MOTOR BLOCK ASSY (LOADING)
Ref. No. Part No. Description Ref. No. Part No. Description
6-1-11. MECHANISM CHASSIS BLOCK ASSEMBLY
801
802
803
804
806
829
805
807
808
M903
812
811
813 820
815
824
807
815
826
815
827
828
815
825
818
819
817
815
822
814
810
809
815816
830
ns
821 823
ns
M902 (Including belt)
ns : not supplied
6-12
6-2. ELECTRICAL PARTS LISTNOTE:• Due to standardization, replacements in the
parts list may be different from the partsspecified in the diagrams or the componentsused on the set.
• -XX, -X mean standardized parts, so they mayhave some difference from the original one.
• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when ordering theseitems.
• CAPACITORS:uF: µF
• COILSuH: µH
• RESISTORSAll resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable
• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
When indicating parts by reference number,please include the board name.
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong modelAUS : Australian modelCH : Chinese modelJE : Tourist model
CK-108CD-366
A-7012-226-A CD-366 BOARD, COMPLETE**********************(IC5101 is not included in this complete board.)
< CAPACITOR >
C5101 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC5102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5103 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5105 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5106 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C5108 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5110 1-113-987-11 TANTAL. CHIP 4.7uF 20% 25VC5111 1-104-851-11 TANTAL. CHIP 10uF 20% 10VC5112 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5113 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5114 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC5116 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< CONNECTOR >
CN5101 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27PCN5102 1-766-336-21 CONNECTOR, FFC/FPC 6P
< FERRITE BEAD >
FB5101 1-414-445-11 FERRITE 0uHFB5102 1-500-284-21 FERRITE 0uHFB5103 1-500-284-21 FERRITE 0uH
< IC >
IC5101 A-7031-359-A CCD BLOCK ASSY (CCD IMAGER)IC5102 6-701-755-01 IC AD80017AJRURL
< COIL >
L5101 1-469-528-91 INDUCTOR 100uHL5102 1-469-525-91 INDUCTOR 10uH
< TRANSISTOR >
Q5101 8-729-037-74 TRANSISTOR UN9213J-(TX).SO
< RESISTOR >
R5101 1-218-990-11 SHORT CHIP 0R5102 1-218-990-11 SHORT CHIP 0
************************************************************
A-7078-105-A CK-108 BOARD, COMPLETE**********************
< BATTERY >
BT5201 1-756-128-11 BATTERY, LITHIUM (SECONDARY)
< CONNECTOR >
CN5201 1-573-927-11 CONNECTOR, FFC/FPC 18PCN5202 1-815-231-11 CONNECTOR, FFC/FPC (ZIF) 40PCN5203 1-794-997-11 PIN, CONNECTOR 20PCN5204 1-794-377-21 PIN, CONNECTOR 8PCN5205 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
CN5207 1-691-346-11 CONNECTOR, FFC/FPC (ZIF) 8P
< DIODE >
D5201 8-719-062-16 DIODE 01ZA8.2(TPL3)D5203 8-719-056-85 DIODE UDZSTE-178.2BD5204 8-719-062-16 DIODE 01ZA8.2(TPL3)D5205 8-719-062-16 DIODE 01ZA8.2(TPL3)D5206 8-719-062-16 DIODE 01ZA8.2(TPL3)
< RESISTOR >
R5201 1-218-953-11 RES-CHIP 1K 5% 1/16WR5206 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR5207 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR5208 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR5209 1-218-954-11 RES-CHIP 1.2K 5% 1/16W
R5210 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5211 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5212 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5213 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5214 1-218-957-11 RES-CHIP 2.2K 5% 1/16W
R5215 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5216 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5217 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5218 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR5219 1-218-960-11 RES-CHIP 3.9K 5% 1/16W
R5220 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR5221 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR5222 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR5223 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR5224 1-218-964-11 RES-CHIP 8.2K 5% 1/16W
Be sure to read “Precautions upon replacing CCD imager”on page 4-9 when changing the CCD imager.
6-13
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
R5225 1-218-970-11 RES-CHIP 27K 5% 1/16WR5226 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR5227 1-218-990-11 SHORT CHIP 0R5228 1-218-990-11 SHORT CHIP 0
< SWITCH >
S5201 1-786-157-11 SWITCH, TACTILE (STOP)S5202 1-786-157-11 SWITCH, TACTILE (REW)S5203 1-786-157-11 SWITCH, TACTILE (RESET)S5204 1-786-157-11 SWITCH, TACTILE (PLAY)S5205 1-786-157-11 SWITCH, TACTILE (FF)
S5206 1-786-157-11 SWITCH, TACTILE (PAUSE)S5207 1-786-148-11 SWITCH, PUSH (1 KEY)(PANEL OPEN/CLOSE)
************************************************************
A-7078-103-A FB-219 BOARD, COMPLETE**********************
< CONNECTOR >
CN6001 1-779-327-11 CONNECTOR, FFC/FPC 6P
< DIODE >
D6001 8-719-074-30 DIODE SML-310LTT86
< PHOTO INTERRUPTER >
PH6001 8-749-016-83 IC GP1S092HCPIPH6002 8-749-016-83 IC GP1S092HCPI
< RESISTOR >
R6001 1-218-990-11 SHORT CHIP 0R6002 1-218-951-11 RES-CHIP 680 5% 1/16WR6003 1-218-947-11 RES-CHIP 330 5% 1/16W
************************************************************
A-7078-100-A JK-217 BOARD, COMPLETE**********************
< CONNECTOR >
CN5305 1-779-334-11 CONNECTOR, FFC/FPC 20P
< DIODE >
D5301 8-719-056-85 DIODE UDZSTE-178.2BD5302 8-719-062-16 DIODE 01ZA8.2(TPL3)
< FERRITE BEAD >
FB5301 1-500-444-11 FERRITE 0uHFB5302 1-469-179-21 FERRITE 0uHFB5303 1-469-179-21 FERRITE 0uHFB5304 1-469-179-21 FERRITE 0uHFB5305 1-469-179-21 FERRITE 0uH
FB5307 1-500-444-11 FERRITE 0uHFB5308 1-500-444-11 FERRITE 0uHFB5309 1-500-444-11 FERRITE 0uHFB5310 1-500-444-11 FERRITE 0uH
< JACK >
J5301 1-793-995-11 JACK, SUPER SMALL TYPE (LANC)J5302 1-694-651-11 TERMINAL BOARD (S VIDEO/AUDIO/VIDEO)
< RESISTOR >
R5301 1-216-864-11 METAL CHIP 0 5% 1/16WR5302 1-216-864-11 METAL CHIP 0 5% 1/16WR5303 1-216-864-11 METAL CHIP 0 5% 1/16WR5304 1-216-864-11 METAL CHIP 0 5% 1/16WR5305 1-216-864-11 METAL CHIP 0 5% 1/16W
< SENSOR >
SE5301 1-803-042-31 SENSOR, ANGULAR VELOCITY (YAW)SE5302 1-803-042-41 SENSOR, ANGULAR VELOCITY (PITCH)
< VARISTOR >
VD5301 1-803-974-21 VARISTOR, CHIPVD5302 1-801-923-11 VARISTOR, CHIPVD5303 1-803-974-21 VARISTOR, CHIPVD5304 1-803-974-21 VARISTOR, CHIPVD5305 1-803-974-21 VARISTOR, CHIP
VD5306 1-803-974-21 VARISTOR, CHIP************************************************************
A-7078-101-A JK-218 BOARD, COMPLETE**********************
< CONNECTOR >
CN5351 1-794-962-11 CONNECTOR, SQUARE TYPE(USB 5P)(USB)CN5352 1-794-276-11 CONNECTOR, SQUARE TYPE 4P (DV IN/OUT)CN5353 1-779-330-21 CONNECTOR, FFC/FPC 12P
< DIODE >
D5351 8-719-062-16 DIODE 01ZA8.2(TPL3)D5352 8-719-056-85 DIODE UDZSTE-178.2BD5353 8-719-056-85 DIODE UDZSTE-178.2BD5354 8-719-078-02 DIODE 1SS357(T3SONY1)
< LINE FILTER >
LF5351 1-419-100-21 INDUCTOR 0uHLF5352 1-419-100-21 INDUCTOR 0uH
< RESISTOR >
R5351 1-218-965-11 RES-CHIP 10K 5% 1/16WR5352 1-218-965-11 RES-CHIP 10K 5% 1/16W
< SWITCH >
S5351 1-786-227-21 SWITCH, TACTILE (SUPER NS)************************************************************
A-7078-102-A LB-077 BOARD, COMPLETE**********************
< CAPACITOR >
C6101 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6102 1-164-505-11 CERAMIC CHIP 2.2uF 16V
< CONNECTOR >
CN6101 1-691-358-21 CONNECTOR, FFC/FPC (ZIF) 20PCN6102 1-691-354-21 CONNECTOR, FFC/FPC (ZIF) 16P
CK-108 FB-219 JK-217 JK-218 LB-077
6-14
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
< DIODE >
D6102 8-719-082-33 DIODE NSCW100-T39
< IC >
IC6101 8-759-581-11 IC NJM2125F(TE2)
< TRANSISTOR >
Q6101 8-729-054-48 TRANSISTOR RN4983FE(TPLR3)Q6102 8-729-054-48 TRANSISTOR N1B04FE-Y/GR(TPLR3)
< RESISTOR >
R6102 1-208-941-11 METAL CHIP 180K 0.5% 1/16WR6103 1-208-719-11 METAL CHIP 33K 0.5% 1/16WR6104 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR6105 1-216-839-11 METAL CHIP 33K 5% 1/16WR6106 1-211-977-11 METAL CHIP 22 0.5% 1/10W
< THERMISTOR >
TH6101 1-810-811-11 THERMISTOR, NTC (1608)************************************************************
A-7078-104-A MA-409 BOARD, COMPLETE***********************
< CAPACITOR >
C5901 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC5902 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V
< CONNECTOR >
CN5901 1-816-232-11 PIN, CONNECTOR (PC BOARD) 4PCN5902 1-779-336-11 CONNECTOR, FFC/FPC 24PCN5903 1-779-328-21 CONNECTOR, FFC/FPC 8P
< DIODE >
D5901 8-719-067-44 DIODE CL-310IRS-X-TUD5902 8-719-067-44 DIODE CL-310IRS-X-TUD5903 8-719-016-74 DIODE 1SS352-TPH3D5905 8-719-056-85 DIODE UDZSTE-178.2B
< FERRITE BEAD >
FB5901 1-500-444-11 FERRITE 0uHFB5902 1-500-444-11 FERRITE 0uHFB5903 1-500-444-11 FERRITE 0uHFB5904 1-500-444-11 FERRITE 0uH
< IC >
IC5901 8-742-221-00 HYB IC SBX3055-01
< JACK >
J5901 1-691-737-41 JACK (SMALL TYPE) (MIC(PLUG IN POWER))J5902 1-569-950-41 JACK (SMALL TYPE) (HEADPHONES)
< RESISTOR >
R5901 1-216-805-11 METAL CHIP 47 5% 1/16W
< VARISTOR >
VD5901 1-801-862-11 VARISTOR, CHIPVD5902 1-801-862-11 VARISTOR, CHIPVD5903 1-801-862-11 VARISTOR, CHIPVD5904 1-801-862-11 VARISTOR, CHIP
************************************************************
A-7078-106-A PD-161 (25SH123) BOARD, COMPLETE(TRV24E/TRV25E)
**************************************A-7012-227-A PD-161 (35SH123) BOARD, COMPLETE
(TRV27E)**************************************
< CAPACITOR >
C5501 1-117-920-11 TANTAL. CHIP 10uF 20% 6.3VC5504 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5505 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5506 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5507 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C5508 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5509 1-135-177-21 TANTALUM CHIP 1uF 20% 20VC5510 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5511 1-164-739-11 CERAMIC CHIP 560PF 5% 50VC5512 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5513 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5514 1-117-920-11 TANTAL. CHIP 10uF 20% 6.3VC5515 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC5516 1-164-870-11 CERAMIC CHIP 68PF 5% 50V
(TRV24E/TRV25E)C5516 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
(TRV27E)
C5517 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5518 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5520 1-131-615-11 TANTAL. CHIP 6.8uF 20% 16VC5521 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C5524 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC5527 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5528 1-135-177-21 TANTALUM CHIP 1uF 20% 20VC5530 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5531 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C5603 1-164-657-11 CERAMIC CHIP 0.015uF 10% 50VC5604 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5605 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
0C5606 1-131-959-91 CERAMIC CHIP 12PF 10% 3KVC5607 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
< CONNECTOR >
CN5501 1-573-364-11 CONNECTOR, FFC/FPC 24PCN5601 1-764-709-11 CONNECTOR, FFC/FPC (LIF) 10PCN5651 1-794-377-21 PIN, CONNECTOR 8PCN5652 1-794-997-11 PIN, CONNECTOR 20PCN5653 1-691-370-11 CONNECTOR, FFC/FPC 6P
CN5654 1-691-384-11 CONNECTOR, FFC/FPC 20P
LB-077 MA-409 PD-161
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
6-15
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
< DIODE >
D5502 8-719-084-47 DIODE 1SV290(TPL3)D5503 8-719-073-01 DIODE MA111-(K8).S0D5601 8-719-073-01 DIODE MA111-(K8).S0D5602 8-719-062-44 DIODE PG1112H-TR (TRV24E/TRV25E)
< FERRITE BEAD >
FB5501 1-414-760-21 FERRITE 0uHFB5502 1-414-760-21 FERRITE 0uHFB5503 1-414-760-21 FERRITE 0uH
< IC >
IC5501 8-752-102-40 IC CXA3592R-T4IC5502 8-759-714-77 IC LZ9FF474IC5601 8-759-564-49 IC TC7W53FU(TE12R)IC5602 8-759-075-70 IC TA75S393F-TE85RIC5651 8-759-573-02 IC BU9735K-E2
< COIL >
L5501 1-469-555-21 INDUCTOR 10uHL5503 1-469-891-21 INDUCTOR 6.8uHL5601 1-428-878-11 INDUCTOR 0uH
< TRANSISTOR >
Q5502 8-729-041-23 TRANSISTOR MGSF1P02LT1Q5503 8-759-054-48 TRANSISTOR UP04601008S0Q5504 8-759-054-48 TRANSISTOR UP04601008S0Q5505 8-729-037-74 TRANSISTOR UN9213J-(K8).SOQ5601 8-729-037-74 TRANSISTOR UN9213J-(K8).SO
Q5603 8-729-054-45 TRANSISTOR UP04312008S0Q5605 6-550-065-01 TRANSISTOR CPH5504-TL-E
< RESISTOR >
R5501 1-218-985-11 RES-CHIP 470K 5% 1/16WR5503 1-208-931-11 METAL CHIP 68K 0.5% 1/16WR5505 1-218-967-11 RES-CHIP 15K 5% 1/16WR5506 1-218-958-11 RES-CHIP 2.7K 5% 1/16WR5507 1-218-973-11 RES-CHIP 47K 5% 1/16W
R5508 1-218-975-11 RES-CHIP 68K 5% 1/16WR5509 1-218-969-11 RES-CHIP 22K 5% 1/16WR5510 1-218-975-11 RES-CHIP 68K 5% 1/16WR5511 1-218-989-11 RES-CHIP 1M 5% 1/16WR5512 1-218-977-11 RES-CHIP 100K 5% 1/16W
R5513 1-218-989-11 RES-CHIP 1M 5% 1/16WR5515 1-218-990-11 SHORT CHIP 0R5516 1-218-965-11 RES-CHIP 10K 5% 1/16WR5519 1-218-990-11 SHORT CHIP 0R5521 1-218-973-11 RES-CHIP 47K 5% 1/16W
R5523 1-218-990-11 SHORT CHIP 0R5531 1-218-980-11 RES-CHIP 180K 5% 1/16WR5532 1-218-977-11 RES-CHIP 100K 5% 1/16WR5533 1-218-989-11 RES-CHIP 1M 5% 1/16WR5534 1-218-953-11 RES-CHIP 1K 5% 1/16W
R5540 1-218-977-11 RES-CHIP 100K 5% 1/16WR5541 1-218-977-11 RES-CHIP 100K 5% 1/16WR5552 1-218-957-11 RES-CHIP 2.2K 5% 1/16W
(TRV24E/TRV25E)R5552 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
(TRV27E)R5591 1-218-953-11 RES-CHIP 1K 5% 1/16W
R5601 1-216-055-00 METAL CHIP 1.8K 5% 1/10WR5602 1-218-980-11 RES-CHIP 180K 5% 1/16WR5603 1-218-969-11 RES-CHIP 22K 5% 1/16WR5605 1-218-942-11 RES-CHIP 120 5% 1/16WR5606 1-218-969-11 RES-CHIP 22K 5% 1/16W
R5607 1-218-949-11 RES-CHIP 470 5% 1/16WR5612 1-218-965-11 RES-CHIP 10K 5% 1/16WR5613 1-218-965-11 RES-CHIP 10K 5% 1/16W
(TRV24E/TRV25E)R5613 1-218-968-11 RES-CHIP 18K 5% 1/16W
(TRV27E)R5651 1-218-946-11 RES-CHIP 270 5% 1/16W
R5652 1-218-987-11 RES-CHIP 680K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB5501 1-234-372-21 RES, NETWORK 100X4 (1005)RB5502 1-234-384-11 RES, NETWORK 1MX4 (1005)RB5503 1-234-378-21 RES, NETWORK 10KX4 (1005)
< TRANSFORMER >
0T5601 1-435-786-31 TRANSFORMER, INVERTER (TRV24E/TRV25E)0T5601 1-437-472-11 TRANSFORMER, INVERTER (TRV27E)
< VARISTOR >
VD5651 1-801-862-11 VARISTOR, CHIP************************************************************
A-7012-225-A VA-117 (GFB) BOARD, COMPLETE***************************
< CAPACITOR >
C4001 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4003 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4101 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4103 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C4104 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC4105 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4106 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4107 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4108 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
C4109 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4110 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4111 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4112 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4113 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4114 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4115 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4116 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4117 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4118 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4119 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4120 1-125-899-11 TANTAL. CHIP 220uF 20% 4VC4121 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4122 1-125-899-11 TANTAL. CHIP 220uF 20% 4VC4123 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
PD-161 VA-117
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
6-16
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
C4125 1-164-858-11 CERAMIC CHIP 22PF 5% 50VC4201 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4204 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4205 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4206 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4208 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4209 1-164-739-11 CERAMIC CHIP 560PF 5% 50VC4210 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4211 1-131-861-91 TANTAL. CHIP 4.7uF 20% 20VC4212 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C4213 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4214 1-164-876-11 CERAMIC CHIP 120PF 5% 50VC4215 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4216 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4217 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4218 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10VC4219 1-164-505-11 CERAMIC CHIP 2.2uF 16VC4302 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4303 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4304 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4305 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4306 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4307 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4308 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4309 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C4310 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4311 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4312 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4314 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4315 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4316 1-135-158-21 TANTALUM CHIP 15uF 20% 4VC4317 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4318 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4319 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4VC4320 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C4321 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16VC4322 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4323 1-131-862-91 TANTAL. CHIP 47uF 20% 4VC4324 1-131-862-91 TANTAL. CHIP 47uF 20% 4VC4325 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4326 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4327 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4328 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4401 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC4402 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V
C4403 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC4404 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16VC4405 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4406 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4410 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C4411 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4412 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC4413 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC4414 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4416 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C4417 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC4419 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4420 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4421 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4423 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C4425 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4426 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4427 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4428 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16VC4429 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V
C4430 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4432 1-104-847-11 TANTAL. CHIP 22uF 20% 4VC4433 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4434 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4435 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C4437 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10VC4501 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC4502 1-164-882-11 CERAMIC CHIP 220PF 5% 16VC4503 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4504 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C4505 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4506 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4507 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4508 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC4509 1-164-936-11 CERAMIC CHIP 680PF 10% 50V
C4510 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC4511 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC4512 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC4513 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4515 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C4516 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4517 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4518 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4519 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4520 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C4521 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4522 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4523 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4525 1-104-851-11 TANTAL. CHIP 10uF 20% 10VC4526 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C4527 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4528 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4529 1-164-947-11 CERAMIC CHIP 0.01uF 50VC4530 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4531 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C4532 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4533 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4534 1-164-506-11 CERAMIC CHIP 4.7uF 16VC4535 1-164-506-11 CERAMIC CHIP 4.7uF 16VC4536 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C4538 1-165-319-11 CERAMIC CHIP 0.1uF 50VC4539 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4541 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4543 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4544 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C4546 1-113-987-11 TANTAL. CHIP 4.7uF 20% 25VC4547 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3VC4548 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3VC4549 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4550 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C4551 1-104-913-11 TANTAL. CHIP 10uF 20% 16VC4553 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4554 1-164-505-11 CERAMIC CHIP 2.2uF 16VC4555 1-164-505-11 CERAMIC CHIP 2.2uF 16VC4556 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
VA-117
6-17
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
C4557 1-104-847-11 TANTAL. CHIP 22uF 20% 4VC4559 1-104-847-11 TANTAL. CHIP 22uF 20% 4VC4601 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4602 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4603 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C4604 1-119-751-11 TANTAL. CHIP 22uF 20% 16VC4605 1-119-751-11 TANTAL. CHIP 22uF 20% 16VC4606 1-119-751-11 TANTAL. CHIP 22uF 20% 16VC4607 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC4608 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR >
CN4001 1-691-384-11 CONNECTOR, FFC/FPC 20PCN4002 1-774-603-21 CONNECTOR, BOARD TO BOARD 100PCN4003 1-691-388-11 CONNECTOR, FFC/FPC 24PCN4004 1-691-376-21 CONNECTOR, FFC/FPC 12PCN4201 1-766-350-21 CONNECTOR, FFC/FPC 20P
* CN4601 1-580-789-21 PIN, CONNECTOR (SMD) 6P
< DIODE >
D4001 8-719-062-16 DIODE 01ZA8.2(TPL3)D4003 8-719-062-16 DIODE 01ZA8.2(TPL3)D4004 8-719-062-16 DIODE 01ZA8.2(TPL3)D4005 8-719-062-16 DIODE 01ZA8.2(TPL3)D4006 8-719-056-85 DIODE UDZSTE-178.2B
D4201 8-719-084-47 DIODE 1SV290(TPL3)D4502 8-719-081-19 DIODE 1SS383(T5RSONY1)D4503 8-719-081-19 DIODE 1SS383(T5RSONY1)D4601 8-719-062-16 DIODE 01ZA8.2(TPL3)D4602 8-719-081-19 DIODE 1SS383(T5RSONY1)
< FUSE >
0F4601 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4602 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4603 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4604 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4605 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)
0F4606 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)
< FERRITE BEAD >
FB4101 1-469-676-22 FERRITE 0uHFB4201 1-469-676-22 FERRITE 0uHFB4202 1-500-329-21 FERRITE 0uHFB4301 1-469-676-22 FERRITE 0uH
< IC >
IC4101 6-701-555-01 IC AN2225NFHQBAIC4201 8-752-100-95 IC CXA3289AR-T4IC4202 8-752-405-57 IC CXD3501AR-T4IC4301 6-701-074-01 IC LA74207W-TBM-EIC4401 8-759-679-11 IC BH7870AKV-E2
IC4501 8-752-102-78 IC CXA3282R-T6IC4505 6-700-139-01 IC R1121N191B-TL
< COIL >
L4101 1-469-525-91 INDUCTOR 10uHL4102 1-469-525-91 INDUCTOR 10uHL4201 1-469-525-91 INDUCTOR 10uHL4202 1-469-891-21 INDUCTOR 6.8uHL4301 1-469-525-91 INDUCTOR 10uH
L4401 1-469-528-91 INDUCTOR 100uHL4501 1-416-670-11 INDUCTOR 33uHL4502 1-416-669-11 INDUCTOR 22uHL4503 1-416-669-11 INDUCTOR 22uHL4504 1-416-669-11 INDUCTOR 22uH
L4505 1-416-670-11 INDUCTOR 33uHL4506 1-416-669-11 INDUCTOR 22uHL4507 1-469-524-91 INDUCTOR 4.7uHL4508 1-469-524-91 INDUCTOR 4.7uHL4509 1-469-524-91 INDUCTOR 4.7uH
L4510 1-469-524-91 INDUCTOR 4.7uHL4511 1-412-056-11 INDUCTOR 4.7uHL4513 1-414-392-41 INDUCTOR 1uHL4514 1-412-056-11 INDUCTOR 4.7uHL4515 1-469-524-91 INDUCTOR 4.7uH
L4516 1-469-526-91 INDUCTOR 22uHL4517 1-469-524-91 INDUCTOR 4.7uHL4519 1-469-524-91 INDUCTOR 4.7uHL4520 1-414-392-41 INDUCTOR 1uHL4522 1-414-392-41 INDUCTOR 1uH
L4601 1-412-056-11 INDUCTOR 4.7uH
< LINE FILTER >
LF4601 1-411-957-11 FILTER, COMMON MODE
< TRANSISTOR >
Q4001 8-729-037-76 TRANSISTOR RN1111F(TPL3)Q4003 8-729-049-92 TRANSISTOR 2SC5585H-T2LQ4101 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)Q4102 8-729-037-61 TRANSISTOR RN2104F(TPL3)Q4103 8-759-054-50 TRANSISTOR UP04501008S0
Q4301 8-729-921-51 TRANSISTOR 2SD1834-T100Q4303 8-729-054-51 TRANSISTOR RN2910FE(TPLR3)Q4304 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4305 8-729-054-52 TRANSISTOR RN1910FE(TPLR3)Q4306 8-729-037-63 TRANSISTOR UN9115J-(K8).SO
Q4307 8-729-054-52 TRANSISTOR RN1910FE(TPLR3)Q4501 8-729-043-60 TRANSISTOR CPH6102-TL-EQ4502 8-729-101-07 TRANSISTOR 2SB798-T1-DLDKQ4503 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4504 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)
Q4505 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4506 8-729-044-33 TRANSISTOR CPH6701-TL-EQ4507 8-759-054-50 TRANSISTOR UP04501008S0Q4508 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4509 8-729-044-33 TRANSISTOR CPH6701-TL-E
Q4510 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4511 8-729-044-58 TRANSISTOR SI2304DS-T1Q4512 8-729-044-58 TRANSISTOR SI2304DS-T1Q4513 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4514 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)
Q4515 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)Q4516 8-759-054-50 TRANSISTOR UP04501008S0Q4517 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)Q4518 8-729-054-49 TRANSISTOR UP04401008S0Q4519 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)
VA-117
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
6-18
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
Q4520 8-729-053-54 TRANSISTOR N1A01FE-Y/GR(TPLR3)Q4521 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)Q4601 8-729-047-68 TRANSISTOR SSM3K03FE(TPL3)Q4602 8-729-056-54 TRANSISTOR TPCS8302(TE12L)Q4603 8-729-804-41 TRANSISTOR 2SB1122-ST-TD
Q4604 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4605 8-729-037-74 TRANSISTOR UN9213J-(K8).SOQ4606 8-729-037-61 TRANSISTOR RN2104F(TPL3)Q4607 8-729-037-61 TRANSISTOR RN2104F(TPL3)Q4608 8-729-023-89 TRANSISTOR 2SJ305(TE85L)
Q4609 8-729-023-89 TRANSISTOR 2SJ305(TE85L)Q4610 8-729-056-54 TRANSISTOR TPCS8302(TE12L)
< RESISTOR >
R4001 1-218-990-11 SHORT CHIP 0R4002 1-218-990-11 SHORT CHIP 0R4003 1-218-990-11 SHORT CHIP 0R4004 1-218-990-11 SHORT CHIP 0R4005 1-218-990-11 SHORT CHIP 0
R4009 1-218-939-11 RES-CHIP 68 5% 1/16WR4010 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR4011 1-216-017-91 RES-CHIP 47 5% 1/10WR4012 1-216-017-91 RES-CHIP 47 5% 1/10WR4013 1-218-990-11 SHORT CHIP 0
R4101 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4102 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4103 1-218-941-81 RES-CHIP 100 5% 1/16WR4104 1-218-981-11 RES-CHIP 220K 5% 1/16WR4105 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4106 1-218-953-11 RES-CHIP 1K 5% 1/16WR4107 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR4108 1-218-953-11 RES-CHIP 1K 5% 1/16WR4109 1-218-953-11 RES-CHIP 1K 5% 1/16WR4110 1-218-965-11 RES-CHIP 10K 5% 1/16W
R4111 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4112 1-218-935-11 RES-CHIP 33 5% 1/16WR4113 1-218-935-11 RES-CHIP 33 5% 1/16WR4114 1-218-935-11 RES-CHIP 33 5% 1/16WR4115 1-218-935-11 RES-CHIP 33 5% 1/16W
R4116 1-218-935-11 RES-CHIP 33 5% 1/16WR4117 1-218-935-11 RES-CHIP 33 5% 1/16WR4118 1-218-953-11 RES-CHIP 1K 5% 1/16WR4119 1-218-953-11 RES-CHIP 1K 5% 1/16WR4120 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4121 1-218-953-11 RES-CHIP 1K 5% 1/16WR4201 1-218-985-11 RES-CHIP 470K 5% 1/16WR4202 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4203 1-218-990-11 SHORT CHIP 0R4205 1-218-958-11 RES-CHIP 2.7K 5% 1/16W
R4206 1-218-973-11 RES-CHIP 47K 5% 1/16WR4207 1-218-975-11 RES-CHIP 68K 5% 1/16WR4208 1-218-969-11 RES-CHIP 22K 5% 1/16WR4209 1-218-975-11 RES-CHIP 68K 5% 1/16WR4210 1-218-989-11 RES-CHIP 1M 5% 1/16W
R4211 1-218-977-11 RES-CHIP 100K 5% 1/16WR4212 1-218-941-81 RES-CHIP 100 5% 1/16WR4213 1-218-941-81 RES-CHIP 100 5% 1/16WR4214 1-218-941-81 RES-CHIP 100 5% 1/16WR4216 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R4217 1-218-989-11 METAL CHIP 1M 0.5% 1/16WR4221 1-218-990-11 SHORT CHIP 0R4222 1-218-990-11 SHORT CHIP 0R4223 1-218-990-11 SHORT CHIP 0R4224 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4301 1-218-971-11 RES-CHIP 33K 5% 1/16WR4302 1-218-981-11 RES-CHIP 220K 5% 1/16WR4303 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR4304 1-218-965-11 RES-CHIP 10K 5% 1/16WR4305 1-218-965-11 RES-CHIP 10K 5% 1/16W
R4306 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4307 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4308 1-218-973-11 RES-CHIP 47K 5% 1/16WR4309 1-218-973-11 RES-CHIP 47K 5% 1/16WR4310 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4311 1-218-953-11 RES-CHIP 1K 5% 1/16WR4316 1-218-937-11 RES-CHIP 47 5% 1/16WR4317 1-218-937-11 RES-CHIP 47 5% 1/16WR4318 1-218-937-11 RES-CHIP 47 5% 1/16WR4319 1-218-937-11 RES-CHIP 47 5% 1/16W
R4401 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4402 1-218-958-11 RES-CHIP 2.7K 5% 1/16WR4403 1-218-965-11 RES-CHIP 10K 5% 1/16WR4404 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4405 1-218-990-11 SHORT CHIP 0
R4406 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4407 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4408 1-218-963-11 RES-CHIP 6.8K 5% 1/16WR4409 1-218-963-11 RES-CHIP 6.8K 5% 1/16WR4410 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4411 1-218-953-11 RES-CHIP 1K 5% 1/16WR4415 1-218-969-11 RES-CHIP 22K 5% 1/16WR4417 1-218-969-11 RES-CHIP 22K 5% 1/16WR4418 1-218-973-11 RES-CHIP 47K 5% 1/16WR4419 1-218-973-11 RES-CHIP 47K 5% 1/16W
R4420 1-218-966-11 RES-CHIP 12K 5% 1/16WR4421 1-218-966-11 RES-CHIP 12K 5% 1/16WR4422 1-218-990-11 SHORT CHIP 0R4423 1-218-965-11 RES-CHIP 10K 5% 1/16WR4424 1-218-966-11 RES-CHIP 12K 5% 1/16W
R4425 1-218-977-11 RES-CHIP 100K 5% 1/16WR4427 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR4430 1-218-990-11 SHORT CHIP 0R4501 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR4502 1-218-971-11 RES-CHIP 33K 5% 1/16W
R4503 1-218-963-11 RES-CHIP 6.8K 5% 1/16WR4504 1-218-985-11 METAL CHIP 470K 0.5% 1/16WR4505 1-218-990-11 SHORT CHIP 0R4506 1-218-967-11 RES-CHIP 15K 5% 1/16WR4507 1-218-965-11 RES-CHIP 10K 5% 1/16W
R4508 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4509 1-216-864-11 METAL CHIP 0 5% 1/16WR4510 1-218-990-11 SHORT CHIP 0R4511 1-218-969-11 RES-CHIP 22K 5% 1/16WR4512 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4513 1-218-990-11 SHORT CHIP 0R4514 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4515 1-208-713-11 METAL CHIP 18K 0.5% 1/16WR4517 1-218-990-11 SHORT CHIP 0R4518 1-218-971-11 RES-CHIP 33K 5% 1/16W
VA-117
6-19
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV24E/TRV25E/TRV27E
R4519 1-218-969-11 RES-CHIP 22K 5% 1/16WR4520 1-218-965-11 RES-CHIP 10K 5% 1/16WR4521 1-218-990-11 SHORT CHIP 0R4524 1-218-973-11 RES-CHIP 47K 5% 1/16WR4525 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4526 1-218-970-11 METAL CHIP 27K 0.5% 1/16WR4527 1-208-720-11 METAL CHIP 36K 0.5% 1/16WR4528 1-218-973-11 RES-CHIP 47K 5% 1/16WR4529 1-218-969-11 RES-CHIP 22K 5% 1/16WR4531 1-218-973-11 RES-CHIP 47K 5% 1/16W
R4532 1-218-977-11 RES-CHIP 100K 5% 1/16WR4533 1-218-969-11 RES-CHIP 22K 5% 1/16WR4534 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4535 1-208-721-11 METAL CHIP 39K 0.5% 1/16WR4536 1-208-701-11 METAL CHIP 5.6K 0.5% 1/16W
R4537 1-218-977-11 RES-CHIP 100K 5% 1/16WR4538 1-218-969-11 RES-CHIP 22K 5% 1/16WR4539 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4540 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR4541 1-208-943-11 METAL CHIP 220K 0.5% 1/16W
R4542 1-218-977-11 RES-CHIP 100K 5% 1/16WR4543 1-218-977-11 RES-CHIP 100K 5% 1/16WR4544 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4545 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR4546 1-208-931-11 METAL CHIP 68K 0.5% 1/16W
R4550 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16WR4551 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR4552 1-208-711-11 METAL CHIP 15K 0.5% 1/16WR4554 1-218-990-11 SHORT CHIP 0R4601 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4604 1-218-977-11 RES-CHIP 100K 5% 1/16WR4605 1-218-989-11 RES-CHIP 1M 5% 1/16WR4607 1-216-797-11 METAL CHIP 10 5% 1/16WR4608 1-218-953-11 RES-CHIP 1K 5% 1/16WR4609 1-218-963-11 RES-CHIP 6.8K 5% 1/16W
R4610 1-218-973-11 RES-CHIP 47K 5% 1/16WR4611 1-218-973-11 RES-CHIP 47K 5% 1/16WR4612 1-218-941-81 RES-CHIP 100 5% 1/16WR4613 1-218-989-11 RES-CHIP 1M 5% 1/16WR4614 1-218-941-81 RES-CHIP 100 5% 1/16W
R4615 1-218-989-11 RES-CHIP 1M 5% 1/16WR4617 1-218-953-11 RES-CHIP 1K 5% 1/16WR4618 1-218-953-11 RES-CHIP 1K 5% 1/16W
< TRANSFORMER >
0T4501 1-435-252-21 TRANSFORMER, DC-DC CONVERTER************************************************************
A-7078-331-A VC-281 BOARD, COMPLETE (SERVICE)(TRV24E)***************************************************A-7078-287-A VC-281 BOARD, COMPLETE (SERVICE)
(TRV25E/TRV27E)***************************************************
************************************************************
VA-117 VC-281
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Electrical parts list of the VC-281 boardare not shown.Pages 6-20 to 6-26 are not shown.
6-27E
DCR-TRV24E/TRV25E/TRV27E
Ref. No. Part No. Description
ACCESSORIES************
1-475-141-61 REMOTE COMMANDER (RMT-814)0 1-475-599-14 ADAPTOR, AC AC-L10A (EXCEPT CH)0 1-475-599-82 ADAPTOR, AC AC-L10B (CH)0 1-569-007-11 ADAPTOR, CONVERSION 2P(JE)0 1-569-008-21 ADAPTOR, CONVERSION 2P(E,HK)
1-573-291-11 CONNECTOR, CONVERSION 21P(AEP,UK,EE,NE)
0 1-696-819-11 CORD, POWER (AUS)0 1-757-293-21 CORD, CONNECTION (USB 5P)0 1-769-608-11 CORD, POWER (AEP,EE,NE,E)0 1-782-476-11 CORD, POWER (CH)
0 1-783-374-11 CORD, POWER (UK,HK)0 1-790-732-11 CORD, POWER (JE)
1-824-097-11 CORD, CONNECTION (AV CABLE)(1.5m)3-072-414-01 SPVD-008 (CD-ROM USB DRIVER)3-075-067-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN)
(TRV25E:UK/TRV27E:UK)
3-075-067-21 MANUAL, INSTRUCTION (FRENCH/GERMAN)(TRV24E:AEP/TRV25E:AEP/TRV27E:AEP)
3-075-067-31 MANUAL, INSTRUCTION (ENGLISH/DUTCH)(TRV24E:AEP/TRV25E:AEP/TRV27E:AEP)
3-075-067-41 MANUAL, INSTRUCTION(SPANISH/PORTUGUESE)
(TRV24E:AEP/TRV25E:AEP/TRV27E:AEP)3-075-067-51 MANUAL, INSTRUCTION (ITALIAN/GREEK)
(TRV24E:AEP/TRV25E:AEP/TRV27E:AEP)3-075-067-61 MANUAL, INSTRUCTION (ENGLISH/SWEDISH)
(TRV24E:NE/TRV25E:NE/TRV27E:NE)
3-075-067-71 MANUAL, INSTRUCTION (DANISH/FINNISH)(TRV24E:NE/TRV25E:NE/TRV27E:NE)
3-075-068-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN)(TRV25E:E, HK, AUS, CH/TRV27E:E, HK, AUS, CH, JE)
3-075-068-21 MANUAL, INSTRUCTION (FRENCH/GERMAN)(TRV25E:E/TRV27E:E,JE)
3-075-068-31 MANUAL, INSTRUCTION (ARABIC/PERSIAN)(TRV25E:E/TRV27E:E,JE)
3-075-068-41 MANUAL, INSTRUCTION (CHINESE)(TRV25E:HK/TRV27E:HK)
3-075-068-51 MANUAL, INSTRUCTION (CHINESE)(TRV25E:E,CH/TRV27E:E,CH,JE)
3-742-854-01 LID, BATTERY CASE (FOR RMT-814)3-987-015-01 BELT (S), SHOULDERA-7024-735-A MEMORY STICK (MSA-8A)X-3950-537-1 CAP ASSY, LENS
NP-FM50 BATTERY PACK (not supplied)
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Take a copy of CAMERA COLORREPRODUCTION FRAME witha clear sheet for use.
— 191 —
⟨FOR CAMERA COLOR REPRODUCTION ADJUSTMENT⟩
DCR-TRV24E/TRV25E/TRV27E
DCR-TRV24E/TRV25E/TRV27E
— 192 —Sony EMCS Co. 2002D1600-1
©2002.4Published by DI Customer Center
9-929-954-31
Revision History
Ver.
1.0
Date
2002.04
History
Official Release
Contents
—
S.M. Rev.issued
—
992995431.pdfReverse