Digital Wireless Calling System

Manual and Security Instructions

Happy Call

Receiver:

Model:HC-201R, HC-202R, HC-213R, HC-314R, HC-314RP

Transmitter:

Model: HC-100T, HC-104T, HC-104TA, HC-104TB, HC-104TS, HC-108T,

HC-140T.

Thank you for purchasing this system. For optimum performance,

please read these instructions carefully before installation.

LEE Handels GmbH Wersener Landstr. 78

49076 Osnabrück / Germany Tel: 0541-9619106, Fax: 0541-9619108

1. Identifying the Parts

Receiver (Monitor)

1) Deleting button (deletes program) 5) Volume control 2) Antenna 6) on-off switch 3) Displaying unit 7) Speaker 4) Power plug 8) Button for function setup

Transmitter (Calling Bell)

2. Function

a) Buttons

B/S You can select one of 12 melodies and the number of bell rings

(Optionally: additionally 9 voices selectable)

D/T You can set the display duration on a number between 1 and 99

seconds

R/E Features save and store process is finished

M Registering the transmitters

Number decreases

Moving digits (and confirmation of the automatic/manual Setting for model HC-304R)

Number increases

b) Bell sounds (The bell sounds have been installed with 12 types of melodies. Optionally: 9 types of voices can be installed)

***The above-listed voice codes can be replaced according to usage (usable only, if the optional program is installed)***

3. Function Setup

a) Setting up the bell sounds and the number of bell rings

- Bell sound setup

Melody code Voice code

No. melody No. voice

01 ding-dong ding-dong 13 ding-dong

02 ding-dong 14 ding-dong No. 00

03 bird sound 15 ding-dong No. 00 is called

04 melody (1) Für Elise 16 ding-dong Nr. 00 staff is called

05 melody (2) 17 ding-dong Thanks for your visit

06 melody (3) 18 No. 00 table, meal is prepared

Code can be replaced 07 melody (4) 19 No. 00 Sir is called

08 melody (5) 20 No. 00 Guest is called

09 melody (6) 21 No. 00 Vehicle is called

10 phone ringing sound

11 sound of dog barking

12 sound of a siren

Press and hold the B/S button for 5 seconds. [01] is shown on the

display and the ding-dong sound is ringing. Each time you push the

B/S button the number increases and the melody sound is changed.

Each time you push the D/T button, the number decreases.

- setup of the number of bell rings

Now you can select the number of bell rings by pushing the

button. Again [01] is shown on the display. Select the number

of bell rings by using the buttons and . Complete the registering process with the R/E button.

b) setting up the display duration: 1- 99 seconds (preset: 10 sec)

Press and hold the D/T button for 5 seconds. [01] is shown on the

display. Select the display duration by using the buttons , ,

and . Afterwards, press the D/T button again to save the desired

display duration.

c) setting up the transmitter numbers (a total of 400 numbers including 100 English expressions can be stored )

1. Press and hold the M button for 5 seconds. [01] is shown on the

display. Use the buttons , and in order to select the

desired number (now one of the two parts of the display flickers).

After having chosen the desired number, press the R/E button

(now both parts of the display flicker). Afterwards push the button on the transmitter. The registered transmitter number is displayed while the bell sound is ringing.

2. If you want to continue to enter further numbers, repeat the above procedure (c.)1.). If you want to use the same number for several transmitters, repeat the above-mentioned procedure, until you have selected the desired number. Now press the button and the button of one of the transmitters, then again the button and the button of another transmitter etc. To complete the process, press the button.

3. If you want to assign a certain bell sound to a certain transmitter, choose the number according to the above-mentioned procedure

(c.)1.). Then choose the desired bell sound by using the M button.

Afterwards press the M button (Now both parts of the display flicker).

To complete the process choose the bell sound preceding the selected

bell sound and then finish by pressing the R/E button. If you now

press the button of the transmitter, the registered number is displayed and the particular bell sound rings. d) Quick Guide

1. setting up the bell sound and the number of bell rings

2. setting up the display duration:1 99 seconds (preset: 10 sec)

3. registering the transmitter

4. registering several transmitters

5. registering the same number for several transmitters

6. assigning special bell sounds to certain transmitters. In this case you have to reset the bell sound to the preset mode. Resetting the bell sound to its preset mode:

Afterwards select the desired bell sound.

4. Special Functions

a. Searching and deleting registered numbers Press and hold the M button

for 5 seconds. [00] is shown on the display. Now activate the search

mode by pressing and holding the R/E button for 5 seconds.

The smallest of the registered numbers is displayed. Search the desired

number by using the buttons and . If you want to delete the

selected number, press the button once (Now both parts of the

display flicker). If you press the same button once again, the selected number will be deleted.

b. Registering the group number (for the receivers HC-503 and 504-RT)

Press and hold the button for 5 seconds. [00] is shown on the display.

Choose the group number by using the buttons , and .

Now press the R/E button in order to register the number.

5. Pager funktion

5.1 Basic Information

a) This pager system displays the transmitter's number both on the receiving monitor and on the pager simultaneously and you can operate it in two ways :- Firstly the transmitter's number is displayed on all the pagers of their carriers, that is ' SYNCHRONOUS CALLING" Secondly when lots of pagers are in use at the same place, the customers' table numbers which are the transmitters' ones are classified and certain transmitters' numbers are displayed only on certain pager, that is ' INDIVIDUAL CALLING ". For example, table no. 1 through 10 are displayed only on Pager No.1 and table no. 11 -15 are only on Pager No.2. In any events the table numbers are displayed on the receiving monitor at the same time as well.

b) Each pager is given its PECULIAR CODE as well as COMMON CODE in 7 digit figure. Its PECULIAR CODE is inscribed on the back of the pager and the COMMON CODE is " 1237576" for all the pagers. When you operate the system in 'SYNCHRONOUS" way, the Common Code above should be applied while in “INDIVIDUAL” way, the Peculiar Code should be done.

5.2. How To Register the Pagers in the Receiving Monitor

5.2.1 Synchronous Calling

Below is to input the Common Code of 7 digit figures: -

1) Push D/T and M button on the monitor at the same time for about 5

seconds until 00 or 000 appears. (It depends on the monitor model)

2) Push M button and the figure 11 or 011 appears.

3) Push M button again to get 01 or 001.

If other than the above appears on the monitor, it should be adjusted as

01 or 001 (Refer to " How To Adjust the Figure " hereinafter)

4) Push D/T button and 01 or 001 blinks.

5) Push M button and 01 or 001 stops blinking.

Now the last figure of 10 or 010 that is "0" should be replaced with the

pager's PECULIAR CODE consisting of 7 digits one by one.

6) Push M to complete the registering procedure. e.g. D/T & M-- M --M --

D/T--M--R/E--- Registration Completed

7) When you press wrong buttons by mistake, push R/E button and it

returns to the initial mode.

5.2.2 Individual Calling

1) Push D/T and M buttons at the same time for about 5 seconds until 00

or 000 appears. (It depends on the monitor model.)

2) Push button to make the displayed figure 01 or 001 .(This is to

show the No.1 pager to be registered. )

3) Push M button and 10 or 010 appears blinking.

Now the last figure of 10 or 010 that is "0" should be replaced with the

pager's PECULIAR CODE consisting of 7 digits one by one.

As a first step of such procedure, insert the first digit of the 7 digit figures which is the INDIVIDUAL CODE of the pager in the "0" position and you

can select the figure by way of pressing or buttons.

4) When you push B/S , either 20 or 020 appears. Now insert the

second digit of the 7 digit figures in the "0" position following as above.

5) PIease insert all the 7 figures as above and press M button.

Next step is to designate the group number of the transmitters and let them be displayed on the No.1 Pager. If you want the customer's table number ( that is the transmitter number) 1 through 5 to be displayed on Pager No.1,

6) Push B/S and make the number as 01, which is the Pager No.1 and

you can select such numbers by way of pressing or .

7) Push D/T and make 05 to designate the group number.

8) Push M and R/E .Then the transmitter numbers 01 through 05 are

registered in the Pager No.01.

When you want to register the Pager No.2, please follow the above procedure

But 01 or 001 on the monitor when you press D/T and M should be

changed 02 or 002 first..

e.g. INDIVIUAL CODE of the Pager is 0111560. Transmitter Numbers 01 through 05 are to be regisrered in the above Pager. PUSH

SIMULTANEOUSLY IINSERT 7 FIGURES

D/T & M – M – B/S -------B/S – M – B/S – D/T – M – R/E-- Registration

Completed

5.2.3 To Delete All the Registered Pager Numbers

Push D/T & M buttons at the same time for about 5 seconds and make

the displayed figures as 00 or 000. After you get these figures, push R/E

for 5 seconds and all the previously registered pager numbers are deleted.

(Note : When you push D/T & M buttons for 5 seconds, all the registered

pager numbers are shown.)

5.2.4 When you press wrong buttons by mistake, push R/E button and it returns

to the initial mode. 6. Inserting the batteries

Open the battery case of the receiver using the enclosed key and unscrew the lid. Insert the batteries. Make sure that the positive and the negative pole of the battery are placed the right way (see figure)

Attention

- only use A23 12V - Dispose used or damaged batteries in an environmentally compatible way according to the applicable law 7. Maintenance

Clean the receiver and the transmitter with a slightly moist cloth. Never use a dry cloth! There is the danger of static charge.

8. Contact for repair work

LEE Handels GmbH, Wersener Landstr. 78, 49076 Osnabrück phone: 0541-4705689, fax: 0541-4705690 info@lee-tech.de 9. Warranty

“Happy Call” has a warranty for a period of two years. The warranty period starts on the date of purchase. Please make sure to keep the receipt to verify the date of purchase. If products are sent in for repair work without this verification or insufficiently packaged, the repair will be charged. Within the warranty period, all deficiencies caused by material or manufacturing defects will be fixed freely of charge. The warranty does not apply to defects resulting from improper use, wearout, modification by anyone other than the manufacturer and the seller, or force majeure. The warranty does not cover consumables (e.g. storage batteries, batteries, package, etc.) nor deficiencies which impair the value and the serviceability of the device only insubstantially. Claims for damages are excluded unless they are due to intent or gross negligence of the manufacturer. Self-evidently, our customer service is also at your disposal after the expiration of the warranty period. For repairs after the expiration date or of damages which cannot be covered by the warranty, you will receive a cost estimate. Product name: Multifunctional Wireless Calling System “Happy Call” Receiver: HC-201R, 202R, 213R, 314R, 314RP Transmitter: HC-100T, 104T, 104TA, 108T. 140T

10. Problem Clearance

Problem Solution

The lamp of the transmitter does not glow.

Check the contacts of the batteries. Replace batteries.

The lamp of the receiver does not glow.

Check the power switch and the adapter.

The receiver continues to display the same number.

Check if the button of the displayed transmitter is held down.

Although the lamp of the receiver glows, no number is displayed.

Reset the number of the transmitter. Replace batteries.

11. Technical Data system : Multifunctional Wireless Calling System

frequency band : 433.050 MHz - 434.790 Mhz operating frequency : 433.92 Mhz transmitting power : 10mW current supply (receiver) : adaptor 230V AC/ 50 Hz / 500mA current supply (transmitter) : A23, 12V ambient temperature : +0°C till +40°C Allowed storage temperature : -10°C till +50°C Range : up to 250m outdoors, up to 50m indoors Size Receiver: HC-201R: 150 x 110 x 48 mm

HC-202R: 217 x 178 x 36 mm HC.203R: 300 x 180 x 53 mm

Transmitter: HC-100T: 70(d) x 60 mm HC-104T: 55 x 55 x 31 mm HC-108T: 65 x 65 x 33

Connection cable of receiver : 2 m