Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Disassembling Snapfon ez One LCD ScreenThis guide will allow the user to remove and replace the LCD screen if the screen is broken.
Geschreven door: John Bender
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 1 van 8
INTRODUCTIE
The LCD screen is the component of the phone that allows the user to see the oututs from the circuitboard once the actions have been converted interally inside the phone from the users input.
GEREEDSCHAPPEN:iFixit Opening Tools (1)Phillips #00 Screwdriver (1)Tweezers (1)Soldering Iron (1)
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 2 van 8
Stap 1 — Remove the battery cover
Make sure the phone is turned offby pressing the power off button toensure no data is lost.
Remove the back battery cover bysliding it downward and pushingsimultaneously.
Picture rights belong to Snapfon®.Picture is used for educationalpurposes only. No copyrightinfringement intended.
Stap 2 — Remove the battery
Using either your thumb or theopening tools, remove the battery byprying the battery out in the directionof the arrow.
If removing battery is for thereplacement of a new battery makesure to properly dispose of the oldbattery at a recycling center.
Picture rights belong to Snapfon®.Picture is used for educationalpurposes only. No copyrightinfringement intended.
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 3 van 8
Stap 3 — Removing the plastic inserts
Remove the rubber inserts from the screw holes using the black metal tweezers. This is done byinserting the tip of the metal tweezers down around the plastic insert.
Stap 4 — Remove the shield screws
Remove the four 3.1mm Phillips #00 screws from the corners.
This is done by turning the screwdriver counter clockwise using little torque.
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 4 van 8
Stap 5 — Separate the case
Separate the phone's front case from the back case.
There is an intermediate decorative outlay around the front cases perimeter. This should beremoved as well.
Stap 6 — Remove the volume slider
Remove the volume slider button byusing the tweezers to pry it out.
The volume slider button may fall outduring the seperation of the frontand back cases, this is ok.
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 5 van 8
Stap 7 — Remove the motherboard
Using the opening tools, separate the circuit board from the inside of the back case by pryingbetween the circuit board and the case as shown.
The last picture is a view of the back of the circuit board.
Stap 8 — Pry the screen back
Using the opening tools, pry the LED screen back to give access to the connecting ribbon cable.
The LED screen is connected to the mother board with light adhesive which can easily beseparated.
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 6 van 8
Stap 9 — Disconnect the display
Use a soldering iron to melt awaythe connection between the ribboncable and circuit board.
The solder iron creates hightemperatures that may cause bodilyharm.
Only make contact with the solderconnection. This will ensure nodamage to the mother board or anyother components of the phone
Stap 10 — Remove the display
Once the solder connection has heated up, apply slight tension to the ribbon cable which will allowfor complete removal of the LED screen.
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 7 van 8
To reassemble your device with a new LED screen, follow these instructions in reverse order. Note thatyou will need to use the soldering iron again to assemble the new LED screen ribbon to the phone.
Disassembling Snapfon ez One LCD Screen Concept: 2019-03-29ID van de handleiding: 24244 -
Dit document is aangemaakt op 2020-01-03 07:39:53 AM (MST).
© iFixit — CC BY-NC-SA nl.iFixit.com Pagina 8 van 8