DOTH-300 - Mobit Bilişim · DOTH-300 KEYWEDGE Date 2013-07-26 ... Emul Key Time(ms) function is supported in the following ... Tab the barcode symbol name from the list,

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 1

CONFIDENTIAL Document D.O.Tel. All rights of reproduction and disclosure reserved.

DOTH-300 KEYWEDGE

D.O.Tel

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 2


Document Revision History

Doc Ver. Release date Description of change Modified by

1.00 2012-10-12 Fist Edition SD. LEE

2.02 2012-11-08 H300XX_KeyWedge_R0201.CAB added

SD. LEE Additional “KeyWedge Home Screen” for Windows Mobile

3.00 2013-02-25 H300XX_KeyWedge_R0303.CAB added.

SD. LEE Additional Emul Key Time(ms)

3.01 2013-06-04 Additional EPC Mode for UHF Option SD. LEE

3.02 2013-07-26 H300XX_KeyWedge_R0312.CAB added SD. LEE

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 3


Table of Contents

Introduction

About This Guide

Chapter 1: Windows CE

1-1: KeyWedge

1-2: KeyWedge Option

1-3: SCANNER Option

1-4: HF Option

1-5: UHF Option

Chapter 2: Windows Mobile

2-1: KeyWedge


2-3: SCANNER Option

2-4: HF Option

2-5: UHF Option

Introduction

KeyWedge is a utility that allows you to add advanced data capturing

capability using barcode scanning, HF RFID and UHF RFID to any application

without writing code. It runs in the background and handles the interface to both

built-in and attached barcode scanners, HF RFID and UHF RFID modules in

DOT mobile computers.

The captured data is converted to keystrokes or copied to the clipboard and

sent to the target application as if it was typed on the keypad.

About This Guide

You can use the following function:

▪ Scanning bar codes (1D/2D)

▪ Reading a HF RFID Tags

▪ Reading a UHF Tags

▪ Emulate a Key-wedge function

¶ NOTE. May vary depending on DOT mobile computer.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 4


Chapter 1: Windows CE

1-1: KeyWedge

You can enable/disable keyWedge for barcode scanner and HF RFID, UHF

RFID reader. Also you can specify each peripheral’s reading condition as

what you want.

Once KeyWedge is launched, you can set and modify all keyWedge settings

on KeyWedge Option.

Components

Supported file is as follows.

Model OS File

DOTH-300S(Q)

DOTH-300C(Q) Windows CE 5.0

KeyWedgeTray.exe

KeyWedgeOpt.exe

DOTH-300S(Q)

DOTH-300C(Q) Windows CE 5.0 ScannerOpt.exe

DOTH-300S(Q) Windows CE 5.0 HFOpt.exe

DOTH-300C(Q) Windows CE 5.0 UHFOpt.exe

Installing KeyWedge

■ Copy the latest version of H300CE_KeyWedge_Rxxxx.CAB to the DOT

Mobile Computer. (Refer to Fig 1-1-1)

■ Run H300CE_KeyWedge_Rxxxx.CAB on the DOT mobile computer to

install KeyWedge. (Refer to Fig 1-1-2)

■ After the installation is complete, KeyWedge will run

automatically.

[Fig 1-1-1] Cab file copy [Fig 1-1-2] Cab file install

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 5


Uninstalling KeyWedge

■ Go to Start > Settings > Control Panel to open the Control Panel window.

Tab the Remove Program icon.

■ Select KeyWedge from the list of installed programs and tap the Remove

button. Tap the Yes button when the Remove Program dialog appears to

uninstall KeyWedge from the DOT mobile computer. (Refer to Fig 1-1-3, Fig

1-1-4, Fig 1-1-5, Fig 1-1-6)

[Fig 1-1-3] Start > Settings [Fig 1-1-4] Control Panel

> Control Panel

[Fig 1-1-5] [Fig 1-1-6]

Remove Programs 1

Remove Programs 2

■ Tab the Yes button when you delete the

user information. Otherwise, tab the No

button.

¶ NOTE. IF you delete user information,

set by default when you reinstall

KeyWedge.

[Fig 1-1-7] Delete user infomation

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 6


KeyWedge Upgrade

■ Refer to Uninstalling Keywedge, uninstall KeyWedge from the DOT mobile

computer.

■ Refer to Installing Keywedge, on the DOT mobile computer to install

KeyWedge.

¶ NOTE. For proper operation, you must remove the previous program,

and then install it.

¶ NOTE. The previous version in order to keep the user information, tab

the “No” button in Figure 1-1-7. Otherwise, all user information after

the upgrade is set by default.

Start KeyWedge

■ Go to Start > Programs > KeyWedge or Tab Tray icon > Options…

(Refer to Fig 1-1-7, Fig 1-1-8)

■ Change the KeyWedge ON state and press the OK button. See 1-2:

KeyWedge Option for more information.

[Fig 1-1-7] KeyWedge [Fig 1-1-8] KeyWedge Tray Icon

¶ NOTE. If KeyWedge the OFF status or Tray Icon HIDE status, the

Tray icon does not appear.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 7



You can set options for KeyWedge. Press the OK button to save your changes

KeyWedge Option.

GeneralSet Tab

■ KeyWedge: ON or OFF KeyWedge

Application.

■ Tray Icon: SHOW or HIDE the tray icon in

“KeyWede ON” mode.

■ Auto Run: During boot-up, the KeyWedge

can run.

[Fig 1-2-1] GeneralSet Tab

■ Device Enable: Select the device you want to use.

¶ NOTE. The SCANNER, UHF and HF depending on DOT mobile

computer will be inactive.

■ About: Show the version information for

the KeyWedge. (Refer to. Fig 1-2-2)

[Fig 1-2-2] About

WedgeSet Tab

■ Select Scan Type: Select SCANNER, HF

and UHF.

■ End of Scan: will define event following

decoded data

■ Key Operation: Select scan operation

mode. According to scan function key, 3

modes are supported.

[Fig 1-2-3] WedgeSet Tab

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 8


Mode Key Down Key Up Success Time out

SYNC Reading Stop Stop Stop

ASYNC Reading No Change Stop Stop

CONTINOUS Reading Stop Retry Retry

■ Timeout: Set the time of reading data before the keyWedge stop.

(1sec~15sec)

■ Interval: Time interval that re-scan after previous scan success in

“CONTINOUS” mode. (100 msec~3000 msec)

■ Prefix: Prefix to data to add a string to the beginning of the data.

■ Suffix: Suffix to data to add a string to the end of the data.

Prefix Data Suffix End Of Scan

[Filed of data]

■ Emul Type: Select Send as events to enable sending keystrokes as keyboard

event and as clipboard event.

■ Emul Key Time(ms): Set the Emul key time option to specify the delay to be

inserted between each keystroke character that is sent, in “Keybaord”. (0 msec ~

1000msec)

■ Notification: Select the Beep or Vibration when scanner read successfully.

¶ NOTE. Emul Key Time(ms) function is supported in the following

versions and above.

- KeyWedge CAB Ver: H300CE_KeyWedge_R303.CAB

KeyMapping Tab

■ Left / Center / Right / Gun key: you can assign each key to different scan

device. (SCANNER, HF, UHF)

■ Setting: If combo box setting, the

configuration window of selected device will

appear. See 1-3: SCANNER Option, 1-4: HF

Option, 1-5: UHF Option for more

information.

[Fig 1-2-4] KeyMapping Tab

¶ NOTE. May vary depending on DOT

mobile computer.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 9


1-3: SCANNER Option

SCANNER Option

You can set barcode symbologies and options for scanner through

SCANNER Option.

Supported barcode symbols are listed.

Check the barcode symbol you want to read.

■ All Enable: Press All Enable button to

enable all decoders for the selected barcode

symbol.

■ All Disable: Press All Disable button to

disable all the decoders.

[Fig 1-3-1] SCANNER Option

■ Factory Reset: Resets all the settings of the Scanner.

¶ NOTE. Supported barcode symbol may vary depending on the scanner

model. If all barcode symbols to enable, it can take a long time to read.

■ Config…: Set the operation status of the scanner.

• Security Level: Set security level. (Only 1D Scanner)

• Enable Code Type: Barcode type is

enabled.

• Select Code Page: Set the code page.

(UTF-8, ANSI)

[Fig 1-3-2] Config…

• Enable Flash Mode: If selected

“Aimer&Illumination”, Flash mode to work. (Only 2D Scanner)

• Aimer/Illumination: set the Aimer/Illumination combinations that can be

used during a decode attempt. (Only 2D Scanner)

• Enable Centering Mode: Barcode in the center of the Aimer is read only.

(Only 2D Scanner)

¶ NOTE. Depending scanner models, “Config...” menu may be different.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 10


Tab the barcode symbol name from the list,

advanced options window appears.

However, the advanced options window is

supported depends on the barcode symbol.

■ Enable Aim ID: AIM ID is output.

[Fig 1-3-2] SCANNER

Advanced option

■ Return Check Digit: Transmit the symbol with or without the check digit.

■ Verify Check Digit: When this feature is enabled, the scan engine checks the

integrity of symbols to verify that the data

complies with specified check digit algorithm.

■ Send Start & Stop: When enabled, the start and stop character transmission.

■ Convert EAN8 to EAN13: Convert EAN-8 to EAN-13.

■ Convert UPCA to EAN13: Convert UPC-A to EAN-13.

■ Convert UPCE to EAN13: Convert UPC-E to EAN-13.

■ Convert UPCE to UPCA: Convert UPC-E to UPC-A.

■ Extended UPCE: Convert UPC-E to UPC-A.

■ Enable FNC1: CODE-128 and GS1-128 barcode to set the FNC1.

■ System Code: Transmit the system character.

■ System & Country Code: Transmit the system character and country code.

■ Full ASCII Mode: Full ASCII is a variant of symbols which pairs characters

to encode the full ASCII character set.

■ Min/Max Length: Minimum / Maximum length for valid barcode string for

this symbol.

■ Only Supplement: The scanner only decodes UPC/EAN symbols with

supplemental characters, and ignores symbols without supplementals.

■ Set Space Character: Determines if there is a space character between the

data from the bar code and the data from the addenda.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 11


¶ NOTE. The representation of active/inactive and terms Depend on the

scanner model.

1-4: HF Option

HF Option

You can set tag for HF RFID through HF Option.

Supported HF tags are listed. Check the HF

tag you want to read.


enable all decoders for the selected HF tag.



[Fig 1-4-1] HF Option

■ Factory Reset: Resets all the settings of the HF RFID.

¶ NOTE. Can not support all the tags, depending on DOT mobile

computer.

¶ NOTE. If all HF tags to enable, it can take a long time to read.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 12


Tab the HF tag name from the list,


■ Data Length: You can set data length

of each HF tag

[Fig 1-4-2] HF Advanced option

Ex) MIFARE Classic tag, support for 4-byte UID.

If UID is “12345678”(Hex),

To read all “12345678” : Begin = 1, End = 4

To read only “1234” : Begin = 1, End = 2




¶ NOTE. The End value should be equal or greater than Begin value.

1-5: UHF Option

UHF Option

You can set option for UHF RFID through UHF Option.

■ Session: Setting is required by the system

to multiple tag reading environment. On the

same tag, the reading time interval can be

adjusted.

- S00: The same tag can be read

consecutively.

- S01: The same tag can be read within about

2 seconds.

[Fig 1-5-1] UHF Option

- S10: The same tag can be read between 2 and 5 seconds.

- S11: Inventory type until you change it, once reading the tag will not read

again.

¶ NOTE. Typically, using the S00 or S01.

¶ NOTE. Duplicate reading time may vary depending on the tag.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 13


■ Tag Inventory type: Set Inventory type of the tag to read.

- A: Only Inventory type A tag is read.

- B: Only Inventory type B tag is read.

- AB: All Inventory type A and B tag is read.

¶ NOTE. Typically, using the A or AB.

■ Q: The option to use when reading multiple tags. Its range is between

1~32768.

¶ NOTE. Typically, using the ~32tags.

■ Select Mask: Used to detect tag you already selected only. Select a tag from

the list of previously read tag and check.

■ EPC: EPC data output is set.

: EPC data is output only.

: PC and EPC data is output.

¶ NOTE. EPC Mode is supported in the

H300XX_KeyWedge_R0310.CAB version and above.

■ Data Format: Set the data output format. (HEX STRING, ASCII)

¶ NOTE. Data Format is supported in the


■ Tx Power control: Used to control the RF output power.

The following table indicates the effects of setting the width of the attenuation.

(unit. dBm)

Max Att1 Att2 Att3 Att4 Att5 Att6 Att7 Att8 Att9

0 -3 -6 -9 -12 -15 -18 -21 -24 -27

■ Firmware Ver: UHF firmware version will be displayed.

■ Factory Reset: Resets all the settings of the UHF RFID.

¶ NOTE. Tx Power adjustment, you can adjust the tag read distance.

¶ NOTE. Tx Power higher, tag read distance is increased. But, Increases

the battery consumption.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 14


Chapter 2: Windows Mobile

2-1: KeyWedge

You can enable/disable keyWedge for barcode scanner and HF RFID, UHF

RFID reader. Also you can specify each peripheral’s reading condition as

what you want.

Once KeyWedge is launched, you can set and modify all keyWedge settings

on KeyWedge Option.

Components

Supported file is as follows.

Model OS File

DOTH-300S(Q)

DOTH-300C(Q) Windows Mobile 6.5

KeyWedgeTray.exe

KeyWedgeOpt.exe

DOTH-300S(Q)

DOTH-300C(Q) Windows Mobile 6.5 ScannerOpt.exe

DOTH-300S(Q) Windows Mobile 6.5 HFOpt.exe

DOTH-300C(Q) Windows Mobile 6.5 UHFOpt.exe

Installing KeyWedge

■ Copy the latest version of H300wM_KeyWedge_Rxxxx.CAB to the DOT

Mobile Computer. (Refer to Fig 2-1-1)

■ Run H300WM_KeyWedge_Rxxxx.CAB on the DOT mobile computer to

install KeyWedge. (Refer to Fig 2-1-2)

■ After the installation is complete, KeyWedge will run

automatically.

[Fig 2-1-1] Cab file copy [Fig 2-1-2] Cab file install

Uninstalling KeyWedge

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 15


■ Go to Start > Settings > System to open the System window. Tab the

Remove Programs applet.

■ Select KeyWedge from the list of installed programs and tap the Remove

button. Tap the Yes button when the Remove Program dialog appears to

uninstall KeyWedge from the DOT mobile computer. (Refer to Fig 2-1-3, Fig

2-1-4, Fig 2-1-5, Fig 2-1-6)

[Fig 2-1-3] Start > Settings [Fig 2-1-4] System

> System

[Fig 2-1-5] [Fig 2-1-6]

Remove Programs 1 Remove Programs 2

■ Tab the Yes button when you delete the user

information. Otherwise, tab the No button.

¶ NOTE. IF you delete user information, set

by default when you reinstall KeyWedge.

[Fig 2-1-7] Delete user information

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 16


KeyWedge Upgrade

■ Refer to Uninstalling Keywedge, uninstall KeyWedge from the DOT mobile

computer.

■ Refer to Installing Keywedge, on the DOT mobile computer to install

KeyWedge.

¶ NOTE. For proper operation, you must remove the previous program,

and then install it.

¶ NOTE. The previous version in order to keep the user information, tab

the “No” button in Figure 1-1-7. Otherwise, all user information after

the upgrade is set by default.

Start KeyWedge

■ Go to Start > KeyWedge applet or Tab Tray icon > Options… (Refer

to Fig 2-1-7, Fig 2-1-8)

■ Change the KeyWedge ON state and press the OK button. See 2-3:

KeyWedge Option for more information.

[Fig 2-1-7] KeyWedge Applet [Fig 2-1-8] KeyWedge Tray Icon

¶ NOTE. If KeyWedge the OFF status or Tray Icon HIDE status, the

Tray icon does not appear.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 17


2-2: KeyWedge Home Screen

KeyWedge Home Screen register

■ Go to Start > Settings > Home to open the Home window. Tab the Items.

Select ( ) KeyWedge from the list of Home Screen and tag the OK button.

(Refer to Fig 2-2-1)

■ Registration is complete, KeyWedge On/Off status is displayed. (Refer to Fig

2-2-2)

■ Tab KeyWedge Home Screen, KeyWedge Option is executed.

KeyWedge Home Screen unregister

■ Go to Start > Settings > Home to open the Home window. Tab the Items.

Select ( ) KeyWedge from the list of Home Screen and tag the OK button.


■ Deregistration is complete, KeyWedge will be removed from Home Screen.


[Fig 2-2-1] Home > Items [Fig 2-2-2] Home Screen

[Fig 2-2-3] Home > Items [Fig 2-2-4] Home Screen

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 18


¶ NOTE. KeyWedge Home Screen function is supported in the following

versions and above.

- KeyWedge CAB Ver: H300WM_KeyWedge_R0201.CAB

- Windows Mobile OS Ver: WMH300XXXXXXX05AX


You can set options for KeyWedge. Press the OK button to save your changes

KeyWedge Option.

GeneralSet Tab

■ KeyWedge: ON or OFF KeyWedge

Application.

■ Tray Icon: SHOW or HIDE the tray icon in

“KeyWede ON” mode.

■ Auto Run: During boot-up, the KeyWedge

can run.

[Fig 2-3-1] GeneralSet Tab

■ Device Enable: Select the device you want to use.

¶ NOTE. The SCANNER, UHF and HF depending on DOT mobile

computer will be inactive.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 19


■ About: Show the version information for

the KeyWedge. (Refer to. Fig 2-3-2)

[Fig 2-3-2] About

WedgeSet Tab

■ Select Scan Type: Select SCANNER, HF

and UHF.

■ End of Scan: will define event following

decoded data

■ Key Operation: Select scan operation

mode. According to scan function key, 3

modes are supported.

[Fig 2-3-3] WedgeSet Tab

Mode Key Down Key Up Success Time out

SYNC Reading Stop Stop Stop

ASYNC Reading No Change Stop Stop

CONTINOUS Reading Stop Retry Retry

■ Timeout: Set the time of reading data before the keyWedge stop.

(1sec~15sec)

■ Interval: Time interval that re-scan after previous scan success in

“CONTINOUS” mode. (100 msec~3000 msec)

■ Prefix: Prefix to data to add a string to the beginning of the data.

■ Suffix: Suffix to data to add a string to the end of the data.

Prefix Data Suffix End Of Scan

[Filed of data]

■ Emul Type: Select Send as events to enable sending keystrokes as keyboard

event and as clipboard event.

■ Emul Key Time(ms): Set the Emul key time option to specify the delay to be

inserted between each keystroke character that is sent, in “Keybaord”. (0 msec ~

1000msec)

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 20


■ Notification: Select the Beep or Vibration when scanner read successfully.

¶ NOTE. Emul Key Time(ms) function is supported in the following

versions and above.

- KeyWedge CAB Ver: H300WM_KeyWedge_R303.CAB

KeyMapping Tab

■ Left / Center / Right / Gun key: you can

assign each key to different scan device.

(SCANNER, HF, UHF)

■ Setting: If combo box setting, the

configuration window of selected device will

appear. See 2-4: SCANNER Option, 2-5:

HF Option, 2-6: UHF Option for more

information.

[Fig 2-3-4] KeyMapping Tab

¶ NOTE. May vary depending on DOT mobile computer.

2-4: SCANNER Option

SCANNER Option

You can set barcode symbologies and

options for scanner through SCANNER

Option.

Supported barcode symbols are listed.

Check the barcode symbol you want to read.


enable all decoders for the selected barcode

symbol.

■ All Disable: Press All Disable button to disable all the decoders.

[Fig 2-4-1] SCANNER Option

■ Factory Reset: Resets all the settings of the Scanner.

¶ NOTE. Supported barcode symbol may vary depending on the scanner

model. If all barcode symbols to enable, it can take a long time to read.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 21


■ Config…: Set the operation status of the scanner.

• Security Level: Set security level. (Only

1D Scanner)

• Enable Code Type: Barcode type is

enabled.

• Select Code Page: Set the code page.

(UTF-8, ANSI)

[Fig 2-4-2] Config…

• Enable Flash Mode: If selected “Aimer&Illumination”, Flash mode to

work. (Only 2D Scanner)

• Aimer/Illumination: set the Aimer/Illumination combinations that can be

used during a decode attempt. (Only 2D Scanner)

• Enable Centering Mode: Barcode in the center of the Aimer is read only.

(Only 2D Scanner)

¶ NOTE. Depending scanner models, “Config...” menu may be different.

Tab the barcode symbol name from the list,


However, the advanced options window is

supported depends on the barcode symbol.

■ Enable Aim ID: AIM ID is output.

[Fig 2-4-3] SCANNER

Advanced option

■ Return Check Digit: Transmit the symbol with or without the check digit.

■ Verify Check Digit: When this feature is enabled, the scan engine checks the

integrity of symbols to verify that the data

complies with specified check digit algorithm.

■ Send Start & Stop: When enabled, the start and stop character transmission.

■ Convert EAN8 to EAN13: Convert EAN-8 to EAN-13.

■ Convert UPCA to EAN13: Convert UPC-A to EAN-13.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 22


■ Convert UPCE to EAN13: Convert UPC-E to EAN-13.

■ Convert UPCE to UPCA: Convert UPC-E to UPC-A.

■ Extended UPCE: Convert UPC-E to UPC-A.

■ Enable FNC1: CODE-128 and GS1-128 barcode to set the FNC1.

■ System Code: Transmit the system character.

■ System & Country Code: Transmit the system character and country code.

■ Full ASCII Mode: Full ASCII is a variant of symbols which pairs characters

to encode the full ASCII character set.

■ Min/Max Length: Minimum / Maximum length for valid barcode string for

this symbol.

■ Only Supplement: The scanner only decodes UPC/EAN symbols with

supplemental characters, and ignores symbols without supplementals.

■ Set Space Character: Determines if there is a space character between the

data from the bar code and the data from the addenda.

¶ NOTE. The representation of active/inactive and terms Depend on the

scanner model.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 23


2-5: HF Option

HF Option

You can set tag for HF RFID through HF Option.

Supported HF tags are listed. Check the HF

tag you want to read.


enable all decoders for the selected HF tag.



[Fig 2-5-1] HF Option

■ Factory Reset: Resets all the settings of the HF RFID.

¶ NOTE. Can not support all the tags, depending on DOT mobile

computer.

¶ NOTE. If all HF tags to enable, it can take a long time to read.

Tab the HF tag name from the list,


■ Data Length: You can set data length of

each HF tag

[Fig 2-5-2] HF Advanced option

Ex) MIFARE Classic tag, support for 4-byte UID.

If UID is “12345678”(Hex),

To read all “12345678” : Begin = 1, End = 4





¶ NOTE. The End value should be equal or greater than Begin value.

DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 24


2-6: UHF Option

UHF Option

You can set option for UHF RFID through UHF Option.

■ Session: Setting is required by the system

to multiple tag reading environment. On the

same tag, the reading time interval can be

adjusted.

- S00: The same tag can be read consecutively.

- S01: The same tag can be read within about

2 seconds.

[Fig 2-6-1] UHF Option

- S10: The same tag can be read between 2 and 5 seconds.

- S11: Inventory type until you change it, once reading the tag will not read

again.

¶ NOTE. Typically, using the S00 or S01.

¶ NOTE. Duplicate reading time may vary depending on the tag.

■ Tag Inventory type: Set Inventory type of the tag to read.

- A: Only Inventory type A tag is read.

- B: Only Inventory type B tag is read.

- AB: All Inventory type A and B tag is read.

¶ NOTE. Typically, using the A or AB.

■ Q: The option to use when reading multiple tags. Its range is between

1~32768.

¶ NOTE. Typically, using the ~32tags.

■ Select Mask: Used to detect tag you already selected only. Select a tag from

the list of previously read tag and check.

■ EPC: EPC data output is set.

: EPC data is output only.

: PC and EPC data is output.

¶ NOTE. EPC Mode is supported in the


DOTH-300 KEYWEDGE

Date 2013-07-26

Rev 3.02

Page 25


■ Data Format: Set the data output format. (HEX STRING, ASCII)

¶ NOTE. Data Format is supported in the


■ Tx Power control: Used to control the RF output power.

The following table indicates the effects of setting the width of the attenuation.

(unit. dBm)

Max Att1 Att2 Att3 Att4 Att5 Att6 Att7 Att8 Att9

0 -3 -6 -9 -12 -15 -18 -21 -24 -27

■ Firmware Ver: UHF firmware version will be displayed.

■ Factory Reset: Resets all the settings of the UHF RFID.

¶ NOTE. Tx Power adjustment, you can adjust the tag read distance.

¶ NOTE. Tx Power higher, tag read distance is increased. But, Increases

the battery consumption.

s

Documents

DOTH-300 - Mobit Bilişim · DOTH-300 KEYWEDGE Date 2013-07-26 ... Emul Key Time(ms) function is supported in the following ... Tab the barcode symbol name from the list,