DRILLING SERVICES - bhge.com · DRILLING SERVICES Directional Drilling Technologies Navi-Drill™ Ultra™ Series Directional drilling motors Applications yyShale gas, onshore, and

DRILLING SERVICES Directional Drilling Technologies

Navi-Drill™ Ultra™ SeriesDirectional drilling motors

Applicationsyy Shale gas, onshore, and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy Underbalanced drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations and

high-temperature environments

Featuresyy Titanium flex shaft improves reliability compared to

universal jointyy Optimized connections increase motor reliabilityyy High-temperature elastomeryy Extended length of the power section (Ultra XL)yy Adjustable kickoff sub (AKO)

Tool size 23⁄8-in. to 12¾-in. (60 mm to 313 mm)

Hole size 2¾-in. to 44-in. (70 mm to 1,118 mm)

Navi-Drill™ Ultra-HP™ SeriesHigh-performance drilling motors

Applicationsyy Shale gas, onshore, and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy OBM environmentsyy Underbalanced drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations

Featuresyy DuraMax high-performance elastomer technologyyy Titanium flex shaft improves reliability compared

to universal jointyy Optimized connections increase motor reliabilityyy Adjustable kickoff sub (AKO)

Tool size 23⁄8-in. to 9½-in. (60 mm to 241 mm)

Hole size 2¾-in. to 28-in. (70 mm to 711 mm)

AutoTrak™ X-tremeMotor-powered rotary steerable system

Applicationsyy Horizontal extended-reach and tight wellbore

spacing wellsyy Complex 3D directional profilesyy Conventional, unconventional, onshore, offshore and

deep water

Featuresyy Pre-contoured X-treme or Ultra HP and wired motoryy Fully modular system, integrated BHA with

short-spaced advanced MWD/LWD sensorsyy Automated 3D continuous proportional

steering methodyy Real-time near-bit inclination and

bidirectional communicationyy Steering mechanism independent of hydraulic

parameters such as flow rate, bit pressure drop, and mud properties

yy Optional near-bit gamma (ZoneTrak G)

Tool size4¾-in. (121 mm)6¾-in. (171 mm)9½-in. (241 mm)


Navi-Drill™ Ultra™ X-treme SeriesDirectional drilling motors

Applicationsyy Shale gas, deep water, geothermal, onshore/offshore,

and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations and

high-temperature environments

Featuresyy X-treme pre-contoured power sectionyy Titanium flex shaftyy Optimized connections increase motor reliabilityyy High-temperature elastomeryy High weight on bit (WOB) bearing assemblyyy Adjustable kickoff sub (AKO)



Navi-Drill™ X-treme SeriesHigh-performance drilling motors

Applicationsyy Shale gas, deep water, geothermal, onshore/offshore,

and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations and high-temperature

environments

Featuresyy X-treme pre-contoured power sectionyy Titanium flex shaftyy Optimized connections increase motor reliabilityyy High-temperature elastomeryy High weight on bit (WOB) bearing assemblyyy Adjustable kickoff sub (AKO)



Navi-Drill™ Ultra™ Curve SeriesHigh BUR directional drilling motors

Applicationsyy Shale gas, onshore, and conventional/unconventionalyy Vertical, directional and horizontal drillingyy Performance drillingyy High-Temperature and OBM environments yy Underbalanced drillingyy Hard/abrasive formations

Featuresyy Reduced bit-to-bend lengthyy DuraMax high-performance elastomeryy Extended-length power sectionsyy Titanium flex shaftyy Optimized connections and high make-up torque yy High temperature elastomeryy Adjustable kickoff sub (AKO)

Tool size 6¾-in. (171 mm)

Hole size 8½-in. to 8¾-in. (216 mm to 222 mm)

© 2017 Baker Hughes, a GE company, LLC – All rights reserved.

Baker Hughes, a GE company, LLC and its affiliates (“BHGE”) provides this information on an “as is” basis for general information purposes and believes it to be accurate as of the date of publication. BHGE does not make any representation as to the accuracy or completeness of the information and makes no warranties of any kind, specific, implied or oral, to the fullest extent permissible by law, including those of merchantability and fitness for a particular purpose or use. BHGE hereby disclaims any and all liability for any direct, indirect, consequential or special damages, claims for lost profits, or third party claims arising from the use of the information, whether a claim is asserted in contract, tort, or otherwise. The BHGE logo is a trademark of Baker Hughes, a GE company, LLC. GE and the GE monogram are trademarks of General Electric Company used under trademark license.

67259

bhge.com

AutoTrak™ VVertical seeking rotary steerable system

Applicationsyy Areas with high formation dips and

deviation tendenciesyy No directional MWD requirementsyy Conventional, unconventional, onshore

and offshore

Featuresyy Simple deployment with minimal surface setupyy Automated 3D continuous proportional




yy Optional downhole motor

Tool size4¾-in. (121 mm)6¾-in. (171 mm) 9½-in. (241 mm)


AutoTrak™ eXpressBasic rotary steerable system

Applicationsyy Field development, probe based directional

MWD serviceyy Conventional, unconventional and onshore

Featuresyy Simple deployment with minimal surface setupyy Automated 3D continuous proportional




yy Optional downhole motoryy Optional gamma ray

Tool size4¾-in. (121 mm) 6¾-in. (171 mm)9½-in. (241 mm)


AutoTrak™ CurveHigh-build rate rotary steerable system

Applicationsyy Vertical, 3D directional, high-build curve and

horizontal drillingyy Probe based directional MWD serviceyy Conventional, unconventional and onshoreyy Pad, high-volume and tight wellbore spacing

drilling environments

Featuresyy Reaches high buildup rates, up to 15°/100ftyy Real-time near-bit gamma and high

frequency vibrationsyy Optimized single piece BHA with higher LCM toleranceyy Automated 3D continuous proportional




yy Includes BHGE Drill Bitsyy Optional downhole motor


Hole size 83⁄8-in. to 105⁄8-in. (213 mm to 270 mm)

AutoTrak™ eXactAdvanced high-build rate rotary steerable system

Applicationsyy Real-time reservoir navigation, integrating multiple

MWD/LWD measurementsyy Multilateral, complex 3D designer,

extended-reach and tight wellbore spacing wellsyy Conventional, unconventional, onshore

and offshore

Featuresyy Reaches high buildup rates, up to 10°/100ftyy Real-time near-bit high frequency vibrationsyy Fully modular system, integrated BHA with





yy Optional downhole motoryy Optional near-bit gamma (ZoneTrak G)

Tool size 4¾-in. (121 mm)6¾-in. (171 mm)

Hole size 5¾-in. to 105⁄8-in. (146 mm to 270 mm)

AutoTrak™ G3Advanced rotary steerable system

Applicationsyy Real-time reservoir navigation, integrating multiple

MWD/LWD measurementsyy Multilateral, complex 3D designer,

extended-reach and tight wellbore spacing wellsyy Conventional, unconventional, onshore, offshore

and deep water

Featuresyy Fully modular system, integrated BHA with





yy Optional downhole motor (AutoTrak X-treme)yy Optional near-bit gamma (ZoneTrak G)

Tool size

4¾-in. (121 mm)6¾-in. (171 mm)8¼-in. (210 mm)9½-in. (241 mm)


NaviTrak™

Directional and gamma MWD service

TeleTrak™

Directional and gamma MWD service

GyroTrak™

Gyroscopic MWD service

Applicationsyy Unconventional shale playsyy Onshore development drillingyy Factory drilling

Featuresyy Real-time directional information yy Downlink capability yy Real-time gamma ray logsyy Optional flow-off logging

Applicationsyy High-LCM environmentsyy Unconventional shale playsyy Onshore development drilling yy Factory drilling

Featuresyy Proven tolerance to high solids and LCM concentrationyy Real-time directional information, including hole

inclination, azimuth, and toolface orientationyy Downlink capability improves telemetry ratesyy Single turbine/restrictor configurationyy Real-time gamma ray logs

Applicationsyy Nearby well casing interferenceyy Kickoff below a casing shoeyy Whipstock orientation and millingyy Relief-well drilling

FeaturesRobust gyroscopic measurements

Tool size

31⁄8-in. (79.4 mm)4¾-in. (120.7 mm)6¾-in. (171.5 mm) 8¼-in. (209.6 mm) 9½-in. (241.3 mm)

Probe diameter 1¾-in. (45 mm)

Hole size 37⁄8-in. to 17½-in. (98 mm to 445 mm)

Tool size4¾-in. (121 mm)6½-in. (165 mm)6¾-in. (172 mm)

Hole size 57⁄8-in. to 97⁄8-in. (149 mm to 250 mm)

Tool size

OnTrak:6¾-in. (172 mm)8¼-in. (210 mm) 9½-in. (241 mm)

NaviTrak:

4¾-in. (152 mm) 6¾-in. (172 mm) 8¼-in. (210 mm) 9½-in. (241 mm)

CoilTrak: 23⁄8-in. (60 mm)3-in (76.2 mm)

Hole size

OnTrak: 83⁄8-in. to 26-in. (214 mm to 660 mm)

NaviTrak: 37⁄8-in. to 17½-in. (128 mm to 312 mm)

CoilTrak: 2¾-in. to 4¾-in. (89 mm to 121 mm)

OnTrak™

Integrated MWD and LWD service

AziTrak™

Deep azimuthal resistivity LWD tool

Applicationsyy Offshore exploration and development yy Complex directional targetsyy Geosteering

Featuresyy Azimuthal gamma ray with imaging capabilityyy High-frequency phase resistivityyy Low-frequency attenuation resistivityyy Fast two-way communication between the surface

and downhole

Applicationsyy Conventional oil and gas reservoirsyy Deep water drillingyy High-angle and horizontal wellsyy Brownfield production enhancementyy Field development through infill drilling

Featuresyy Compact, fully integrated sub featuring

close-to-the-bit measurementsyy Close-to-the-bit, deep-reading azimuthal resistivity

allows early detection of remote conductive boundaries yy Intuitive, dynamic, real-time display of

reservoir boundaries

Tool size





ZoneTrak™ RAt-bit resistivity LWD service

Applicationsyy Casing and coring point selectionyy Salt exit detectionyy Real-time pressure managementyy Geo-stoppingyy All drilling environmentsyy High-resistivity contrast formations

Featuresyy Identifies top and bottom of reservoiryy Detects formation changes faster to adjust drilling

fluid parametersyy Includes forward response modelingyy Real-time data transmitted through BHGE

WellLink™ service

Tool size 6¾-in. (172 mm)9½-in. (241 mm)

Hole size 83⁄8-in. to 18¼-in. (213 mm to 464 mm), dependent upon mud type

ZoneTrak™ GNear-bit gamma service

Applicationsyy Casing and coring point selectionyy Geo-stopping yy Reservoir navigation yy All drilling environments

Featuresyy True azimuthal gamma ray measures 6 feet above

the bityy Imaging capabilitiesyy Two gamma sensors yy Real-time gamma data can be displayed through BHGE

WellLink™ service


Hole size 5¾-in. to 18¼-in. (146 mm to 464 mm)

aXcelerate™ PLUSHigh-speed mud-pulse telemetry service

Applicationsyy Critical wellsyy Geosteering and optimized wellbore placementyy Extended-reach and complex 3D wellsyy Performance drillingyy Required for extended formation

evaluation BHA’s

Featuresyy Downhole adjustable pulser setup via downlinkyy Real-time formation evaluation data for

reservoir navigationyy High-resolution downhole drilling dynamics data yy Bandwidth up to 40 bits per second physical and up to

256 bits per second compressed



Wired-Pipe TelemetryApplicationsyy Extended-reach wellsyy Underbalanced drillingyy Geosteeringyy Performance drillingyy Required for extended formation evaluation BHA’syy Enabling technology for delivering measurements

along the string

Featuresyy Real-time formation evaluation memory quality data

for reservoir navigationyy Bandwidth up to 57,600 bits per secondyy High-resolution downhole drilling dynamics data of the

BHA and optional along the stringyy Drilling in environments where data transmission was

not possible with mud pulse telemetry

Tool size



SureTrak™

Steerable drilling liner service

GaugePro™ XPR/XPSConcentric expandable hole enlargement

GaugePro™ EchoOn Command Digital Downhole Reamer

Applicationsyy Onshore or offshore environments yy Interbedded formationsyy Wellbore instability issues, including swelling shale

and weak sedimentsyy Lost circulationyy Depleted formations

Featuresyy Changeable pilot bottomhole assembly (BHA)

eliminates the need for liner retrieval yy BHA design tailored to wellsite requirementsyy Uses AutoTrak™ system with modular

MWD/LWD servicesyy Incorporates X-treme motor technologyyy Liner shoe with decoupled reamer bit separates BHA

drilling dynamics from the liner

Applicationsyy Rotary steerable and rotary operations yy Deepwater projectsyy Wellbore enlargementyy Unconsolidated formationsyy Salt drilling

Featuresyy StaySharp™ premium polished cutter technology with

improved diamond material and interfaceyy StayTough™ hardfacingyy Active blade retraction yy Application-specific cutter blades yy Blade operation, protecting the casing

Applicationsyy Deep water & on-shore projectsyy Selective under reamingyy ECD managementyy Rat-Hole eliminationyy Hole cleaning

Featuresyy On-Demand unlimited activationsyy 5 minute activation/deactivationyy Real-time communicationyy Downlink via Mud Pulse or wired drill pipeyy Confirms real-time cutter blade actuation and

OD positionyy Real-time VSS and tool diagnosticsyy No pressure drop dependencies, no shoulder testsyy Up to 3 reamers in one BHAyy Independent of mud flowyy Memory for post analysis

Tool size 4¾-in. with 7-in. liner 6¾-in. with 95⁄8-in. liner

Hole size 8½-in. to 12¼-in. (216 mm to 311 mm)

Series 6 6-in. x 7-in.

Series 6.5 6½-in. 7½-in.

Series 8 8½-in. x 97⁄8-in.

Series 9 9½-in. x 11¾-in.

Series 10 105⁄8-in. x 12¼-in.

Series 12 12¼-in. x 14¾-in.

Series 13 13½-in. x 16-in.

Series 14 14½-in. x 17½-in.

Series 16 16½-in. x 20-in.

Series 18 181⁄8-in. x 22-in.

BHA Body Pass-Thru Maximum Hole Size

Series 6 4¾-in. 6-in. 8¾-in.

Series 8 6¾-in. 8½-in. 97⁄8-in.

Series 10 8¼-in. 105⁄8-in. 12¼-in.

Series 12 9½-in. 12¼-in. 14¾-in.

Series 14 9½-in. 14½-in. 17¾-in.

Series 16 9½-in. 16½-in. 22-in.

SIGNALS™ SurveillanceOperations Monitoring Services

SIGNALS™ ServicesWellsite and remote operations monitoring

ApplicationsAll Drilling Environments

Featuresyy Collection and interpretation of real-time

operational datayy Detailed record of drilling parametersyy Provides integrated data visualization yy Structured workflow and proactive

communication protocols

SIGNALS™ DefenseWellbore Integrity Services

SIGNALS™ OptimeDrilling Optimization Services

Applicationsyy Exploration Wellsyy Offshore drilling environmentsyy Narrow pressure windows yy Complex and problematic formations

Featuresyy Early kick detection with automated smart alarmsyy Identification of wellbore instability issuesyy Pore pressure trend analysisyy Hole cleaning analysis


Featuresyy Focused, real-time, offsite 24-hour monitoring and

analysis of datayy Integrated drilling advice through wellsite, operator,

and remote support teamsyy Structured workflow and proactive

communication protocolsyy Pre-well and Post-well service analysis

CoPilot™

Real-time drilling performance service

Applicationsyy Deep wateryy Extended reach drillingyy Challenging interbedded or complex well formationsyy Conventional/unconventional oil and gasyy Salt drillingyy Shale gas drilling

Featuresyy Real-time data transmission and expert interpretationyy Bending moment and bending orientationyy Accurate downhole weight and torqueyy Downhole dynamics measurements including whirl

Tool size

4¾-in. (121 mm)6¾-in. (171 mm) 8¼-in. (210 mm) 9½-in. (241 mm)


DRILLING SERVICES Formation Evaluation Technologies

OnTrak™

Integrated MWD service

MagTrak™

Magnetic resonance service

AziTrak™

Deep azimuthal resistivity tool

Applicationsyy Offshore exploration and development yy Complex directional targetsyy Geosteering

Featuresyy Azimuthal gamma ray with imaging capabilityyy High-frequency phase resistivityyy Low-frequency attenuation resistivityyy Fast two-way communication between the surface

and downhole

Applicationsyy Deep water drillingyy Extended-reach drilling yy Reservoirs with complex or mixed lithologyyy Low resistivity contrast reservoirs

Featuresyy Accurate T2 magnetic resonance logsyy Minimizes motion effects on measurements induced

by drilling vibrationyy Sourceless porosityyy Real-time T2 spectrum transmitted to surface

Applicationsyy Conventional oil and gas reservoirsyy Deep water drillingyy High-angle and horizontal wellsyy Brownfield production enhancementyy Field development through infill drilling

Featuresyy Compact, fully integrated sub featuring

close-to-the-bit measurementsyy Close-to-the-bit, deep-reading azimuthal resistivity

allows early detection of remote conductive boundaries yy Intuitive, dynamic, real-time display of

reservoir boundaries

Tool size


Hole size* 5¾-in. to 26-in. (146 mm to 669 mm)

Tool size4¾-in. (121 mm)6¾-in. (172 mm)8¼-in. (211 mm)




LithoTrak™

Density and porosity service

Applicationsyy Formation and reservoir evaluation in all well profilesyy Reservoir navigationyy Wellbore stability monitoring

Featuresyy Acquires data using straight hole rotary, steerable

motors, or rotary steerable drilling systems yy Measurements are collected by a standoff binning

process to provide accurate, compensated density and Pe values

yy Real-time borehole density images and caliper measurements in all mud types

yy Accurate identification of fluid contacts and hydrocarbon typing

yy Azimuthal borehole caliper and real-time, short-spaced borehole images


Hole size* 57⁄8-in. to 12¼-in. (149 mm to 311 mm)

© 2017 Baker Hughes, a GE company, LLC – All rights reserved.

Baker Hughes, a GE company, LLC and its affiliates (“BHGE”) provides this information on an “as is” basis for general information purposes and believes it to be accurate as of the date of publication. BHGE does not make any representation as to the accuracy or completeness of the information and makes no warranties of any kind, specific, implied or oral, to the fullest extent permissible by law, including those of merchantability and fitness for a particular purpose or use. BHGE hereby disclaims any and all liability for any direct, indirect, consequential or special damages, claims for lost profits, or third party claims arising from the use of the information, whether a claim is asserted in contract, tort, or otherwise. The BHGE logo is a trademark of Baker Hughes, a GE company, LLC. GE and the GE monogram are trademarks of General Electric Company used under trademark license.

67259

bhge.com

VisiTrak™

Geospatial Navigation and Analysis Service

Applicationsyy Onshore / Offshore yy Deepwateryy Conventional Oil & Gasyy SAGDyy Pilot hole mitigationyy Highly deviated, horizontal and extended reach wellsyy Reservoir Navigation / Geosteering and reservoir

mapping

Featuresyy Low frequency measurements for extra deep

resistivity measurements yy Cross component antenna technology allowing

azimuthal sensitivityyy Early reservoir detection from overburden yy Multiple boundary / fluid contact detection yy Real-time - reservoir architecture mapping to

seismic scale


Hole size 8½-in. to 12¼-in. (216 mm to 311 mm)

ZoneTrak™ RAt-bit resistivity service

Applicationsyy Casing and coring point selectionyy Salt exit detectionyy Real-time pressure managementyy Geo-stoppingyy All drilling environmentsyy High-resistivity contrast formations

Featuresyy Identifies top and bottom of reservoiryy Detects formation changes faster to adjust drilling

fluid parametersyy Includes forward response modelingyy Real-time data transmitted through BHGE

WellLink™ service


Hole size 83⁄8-in. to 18¼-in. (213 mm to 464 mm), dependent upon mud type

ZoneTrak™ GNear-bit gamma service

Applicationsyy Casing and coring point selectionyy Geo-stopping yy Reservoir navigation yy All drilling environments

Featuresyy True azimuthal gamma ray measures 6 feet above

the bityy Imaging capabilitiesyy Two gamma sensors yy Real-time gamma data can be displayed through BHGE

WellLink™ service



StarTrak™

Electrical imaging service

Applicationsyy Complex or thin-bedded reservoirsyy Shale gas playsyy Geosteeringyy Wellbore stability

Featuresyy Acquires high-resolution images at penetration rates

up to 150 ft/hryy Very tolerant of moderate levels of stick/slip yy Real-time images displayed through BHGE

WellLink™ serviceyy Detailed fracture analysis


Hole size 5¾-in. to 9½-in. (146 mm to 241 mm)

SoundTrak™ Acoustic service

SeismicTrak™

Seismic-while-drilling service

Applicationsyy Pore-pressure predictionyy Acoustic slowness in large holes and slow formationsyy Seismic time-depth tieyy Acoustic porosity evaluationyy Early detection of shallow gasyy Acoustic light hydrocarbon indicator

Featuresyy Proprietary quadrupole transmitter technology yy Multi-frequency sourceyy Measures compressional and shear slownessyy Salinity-independent measurements for real-time

pore-pressure prediction yy Real-time geomechanical rock properties measured for

wellbore stabilityyy High attenuation, band-reject isolatoryy Sourceless porosity

Applicationsyy Deep water drillingyy Vertical, Highly deviated, horizontal, or

extended-reach wellsyy Determining casing and coring pointsyy Reducing seismic uncertaintyyy Identify over-pressured zones below the bit

Featuresyy Measurements acquired during natural breaks in

the drilling processyy Reduces overall cost of logging programyy Employs precise clock mechanisms for highly accurateyy Precise clock mechanisms for highly accurate

check-shot time-depth pairsyy Immediate data-capture feedback during

drilling processyy Rugged design with redundant sensors and

large memory

Tool size6¾-in. (172 mm)8¼-in. (210 mm)9½-in. (241 mm)

Hole size 57⁄8-in. to 26-in. (150 mm to 660 mm)

TesTrak™

Formation pressure while-drilling service

FASTrak™

Fluid analysis, sampling and testing service

Applicationsyy Onshore and offshore drilling: all well types and

formation typesyy Drilling hazard mitigationyy Reservoir characterization

Featuresyy SmarTest™ intelligent testingyy SmartPad™ closed-loop sealingyy Real-time pore pressure measurements yy Real-time gradient analysis to identify fluids

and contacts yy Real-time formation mobility

Applicationsyy Single-phase fluid sampling and

formation-pressure testingyy Reservoir knowledge enhancement, drilling efficiency

and operational safetyyy Onshore / Offshoreyy Deepwateryy Highly deviated, extended reach and

horizontal wells

Featuresyy SmarTest™ intelligent testingyy SmartPad™ closed-loop sealingyy Multiple drawdowns per test station yy Real Time Fluid Analysisyy Direct measurement of Density, Viscosity, Refractive

Index and Soundspeedyy Sampling and Pressure Testing while circulatingyy High Accuracy Pump Controlyy Compressibility and Drawdown Mobilityyy Capture of up to 16 Single Phase Samplesyy Multiple samples per pressure stationyy Chemical Resistant metallurgyyy Single Phase Sample Tank Technology


Hole size 83⁄8-in. to 26-in. (213 mm to 660 mm)

Nominal hole size

8½-in. to 12¼-in. (216 mm to 311.2 mm)


Hole size 5¾-in. to 17½-in. (146 mm to 445 mm)


Hole size 8½-in. to 11¾- in. (216 mm to 298 mm)

aXcelerate™ PLUSHigh-speed mud-pulse telemetry service

Wired-Pipe Telemetry

Applicationsyy Critical wellsyy Geosteering and optimized wellbore placementyy Extended-reach and complex 3D wellsyy Performance drillingyy Required for extended formation evaluation BHA’s

Featuresyy Downhole adjustable pulser setup via downlinkyy Real-time formation evaluation data for

reservoir navigationyy High-resolution downhole drilling dynamics data yy Bandwidth up to 40 bits per second physical and up to

256 bits per second compressed

Applicationsyy Extended-reach wellsyy Underbalanced drillingyy Geosteeringyy Performance drillingyy Required for extended formation evaluation BHA’syy Enabling technology for delivering

measurements along the string

Featuresyy Real-time formation evaluation memory quality data for

reservoir navigationyy Bandwidth up to 57,600 bits per secondyy High-resolution downhole drilling dynamics data of the

BHA and optional along the stringyy Drilling in environments where data transmission was

not possible with mud pulse telemetry



Tool size



Conventional Coring

JamBuster™

Jam mitigation coring system

HydroLift™

Full closure catcher coring system

LaserCut™ Quick access coring system

Applicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy High Pressure / High Temperature formationsyy Shale Gas, Deep Water & Geothermal Drillingyy Horizontal and deviated Drillingyy Consolidated and Unconsolidated formations

Featuresyy HT-Series (Heavy Duty, High Torque) Core Barrelsyy BHGE Core Bits yy CoreGard™ Low Invasion Technology yy Disposable, vented Inner Barrels yy Non Rotating Inner Tube Stabilizers

Applicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy High Pressure / High Temperature formationsyy Shale Gas, Deep Water & Geothermal Drillingyy Horizontal and deviated Drillingyy Consolidated and fractured formations

Featuresyy Telescoping Sleeves allow continuous coring after

jamming inside Inner Barrelyy Modular Coring System

Applicationsyy Recovery of unconsolidated formation materialyy HydroLift is available for the HT30 and HT60 core

barrels, cutting 4 and 5¼-inch diameter core samples, respectively

yy The System also includes a slick entry feature that prevents fractured core from catching or jamming into the catcher

Featuresyy Full closure catcher completely seals the inner barrelyy Slick, unobstructed core entry yy Back-up conventional core catcher

Applicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy Shale Gas, Deep Water & Geothermal Drillingyy Horizontal and deviated Drilling

Featuresyy Integral, one piece liners with LaserCut along its lengthyy Rapid access on surfaceyy Utilizes conventional equipment

Tool Description Core Size

Tool Size

HT10: 4¾-in. (120.6 mm)HT12: 51⁄8-in. (130.2 mm)250P: 5½-in. (139.7 mm)250P: 6¼-in. (158.7 mm)HT30: 6¾-in. (171.4 mm)

HT30 Max: 7¼-in. (184.2 mm)HT40: 8-in. (203.2 mm)

HT60: 9½-in. (241.3 mm)Large Core HT60

25⁄8-in. (66.7mm)3-in. (76.2mm)

3½-in. (76.2mm)4-in. (101.6mm)4-in. (101.6mm)

4½-in. (114.3mm)4¾-in. (120.6mm)5¼-in. (133.4mm)6-in. (152.4mm)

Hole Size 5¾-in. to 17½-in. + (146.0 - 444.5 mm +)


Tool Size

HT10: 4¾-in. (120.6mm)HT12: 51⁄8-in. (130.2 mm)HT30: 6¾-in. (171.0 mm)

HT30 Max: 7¼-in. (184.2 mm)HT40: 8-in. (203.2 mm)

HT60: 9½-in. (241.3 mm)

21⁄8-in. (54.0mm)2½-in. (63.5mm)3½-in. (88.9mm)4-in. (101.6mm)

4¾-in. (120.6mm)5¼-in. (133.4mm)

Hole Size 5¾-in. to 17½-in. + (146.0 mm to 444.5 mm +)


Tool Size

HT30: 6¾-in. (171.0 mm)HT60: 9½-in. (241.3 mm)

4-in. (101.6mm)5¼-in. (133.4mm)

Hole Size 8½-in. to 17½-in. + (146.0 - 444.5 mm) +


Tool Size

HT12: 51⁄8-in. (130.2 mm)HT30: 6¾-in. (171.0 mm)

HT30 Max: 7¼-in. (184.2 mm)

2½-in. (63.5 mm)3½-in. (88.9.6 mm)

4-in. (101.6 mm)

Hole Size 61⁄8-in. to 17½-in. + (155.6 mm to 444.5 mm +)

CoreGel™

Downhole core encapsulation system

Applicationsyy Onshore / Offshore yy Conventional and Unconventional formationsyy Horizontal and deviated Drilling

Featuresyy Encapsulates cores in a viscous, noninvasive,

protective gelyy Increases core integrity during cuttingyy Helps prevent jammingyy Reduces drilling fluid contamination


Tool Size

HT30: 6¾-in. (171.0mm)HT60: 9½-in. (241.3mm)

4-in. (101.6mm)5¼-in. (133.4mm)

Hole Size 8½-in to 17½-in. (215.9 to 444.5mm)

SOr™

Sponge liner coring system

Applicationsyy Specialized Coring operationsyy All Drilling Environmentsyy Enhanced oil recovery projectsyy Consolidated formations

Featuresyy Molded, oil-absorptive sponge lineryy Foam reinforced webbingyy LaserCut aluminum liner system yy Proprietary pressure-compensating piston design


Tool Size HT30: 6¾-in. (171.0mm) 3½-in (76.2mm)

Hole Size 8½-in. (215.9mm)

Core BitsApplicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy Extremely hard and abrasive formationsyy Unconsolidated formationsyy Highly fractured formationsyy Shale Gas, Deep Water and Geothermal Drillingyy Horizontal and deviated Drillingyy Enhanced Oil Recovery Projects, specialized SOr Sponge

Precision Core Bits

Featuresyy Talon Series PDC Core Bitsyy IRev Impregnated Core Bitsyy Natural Diamond Core Bits

Tool size 4¾-in. to 9½-in. (120.6 mm to 241.3 mm)

Hole size 5¾-in. to 17½-in. + (146.0 mm to 444.5 mm +)

Oriented Coring Services*


Tool Size

HT10: 4 ¾-in. (120.6mm)HT12: 5 1

8-in. (130.2mm)HT30: 6 ¾-in. (171.0mm)

HT30 Max: 7 ¼-in. (184.2mm)HT40: 8-in. (203.2mm)

HT60: 9 ½-in. (241.3mm)

2 5⁄8-in (66.7mm) 3 -in (76.2mm)4 -in (101.6mm)

4 ½-in (114.3mm)4 ¾-in (120.6mm)5 ¼-in (133.4mm)

Hole Size 5 ¾-in to 17 ½-in. + (146.0 - 444.5mm +)

* BHGE will only provide the needed interface to the survey tools

Applicationsyy Onshore / Offshore yy Conventional and Unconventional formationsyy Consolidated formations

Featuresyy Knives in shoe assembly continuously scribe the coreyy Oriented tools in the core barrel and survey tool

rotationally coupledyy Identifies the core’s in situ orientation

FE-Vision™

Cuttings and Gas Evaluation Services

Vision ServicesWellsite and remote formation evaluation

HC-Vision™

Reservoir Characterization Services

CI-Vision™

Carbon Isotope Analysis

TRU-Vision™

Quantitative Gas Extraction and Analysis

STRATA-Vision™

Advanced Cuttings Evaluation


Featuresyy Gas sample collection and analysis of

Methane- Pentane gassesyy Cuttings sample collection and lithology analysisyy Provides integrated data visualization yy Identification of potential hydrocarbon presence


Featuresyy Provides visual reservoir interpretation logsyy Provides indications of hydrocarbon porosity,

permeability, volumetrics, saturations, geohazards and fluid compartmentalization

yy Processes data from current drilling projects and legacy projects independent of SLS provider

yy Integrates with other formation evaluation services


Featuresyy Continuous C1-C3 and CO2 Carbon Isotope ratio analysisyy Provides insight of source rock, maturity, transition

zones and connectivityyy Indicators to biogenic, thermogenic or mixed gas

and their originyy Purpose built, rack mounted lab quality equipment


Featuresyy Quantitative analysis of C1-C8 organic hydrocarbons and

key inorganic gassesyy Heated quantitative gas extraction yy Constant flow and constant temperatureyy Continuous quantification and visualization of

mud density yy Automated and continuous gas extraction efficiency

Applicationsyy Unconventional wellsyy Extended-reach and horizontal wellsyy Slimhole drilling yy HPHT zones

Featuresyy Formation evaluation log correlation with other

FE datasetsyy Identification of productive zones yy Chemostratigraphic profile and surface

spectral - gammayy Near real-time formation and kerogen

geochemical analysis

Documents

DRILLING SERVICES - bhge.com · DRILLING SERVICES Directional Drilling Technologies Navi-Drill™ Ultra™ Series Directional drilling motors Applications yyShale gas, onshore, and