Embed Size (px)
Citation preview
Specifications
DS8000 Digital Wireless Microphone System
SCALE 6.000
Receiver 8 channel front
The SACOM DS8000 Series Digital Wireless Microphone System delivers reliable professional sound quality and simplified setup. The DS Series wireless system is based on 24-bit, 48 KHz, digital audio RF technology and it is available in a number of frequency bands that accommodate most government requirements worldwide. Confidentiality is assured with SACOM’s 256-bit encryption algorithm, which conforms to the US Government AES (FIPS PUB 197) specifications.
The receiver is modular in design with up to eight (8) field replaceable modules per receiver. Up to 64 receiver channels can operate with one pair of antennas without an external antenna distribution amp.
Transmitters include: a belt pack for use with lavaliere and headset microphones; a handheld microphone; a conference table-top microphone; and a podium gooseneck microphone.
Each system comes with SACOM Remote Computer Software which features full system monitoring and control via the graphical user interface.
Digital Wireless Microphone Systems
Sacom l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001
DS System OverviewRF Technology: 24-Bit digital audio: No Companding• Encryption: 256 bit key. Meets US Gov. AES (FIPS PUB 197)* standard. • Digital Carrier Frequency Range: Available in several bands: • see: WWW.SACOMUSA.COM for detailsS/N Ratio: 108 dB (Typical ‘A’ weighted)• THD: <0.03%• Frequency Response: 20 Hz - 20 KHz +/- 1.5 dB (Stage Mode)• Stability: < 5 ppm• Channel Spacing: 1.625 MHz or 812.5KHz (programmable) • Range: >100 meters line-of-sight• Latency: < 3 mSec (Stage Mode Digital Output) •
Receiving Mode: True diversity• External Antennas: Optional• Power Supply: 100-240 VAC 50-60 Hz, 15 Watts, 320mA slow-blow • fuse (spare included)1-U Rack-Mount Case: 4 or 8 independent receivers modules• Analog Audio Outputs: Balanced XLR or terminal blocks; +2 dBV, +4 • dBu, 100 Ohm source impedance; pin1=chassis ground, pin2 = hot, pin3 = cold. The output connectors are protected against inadvertent application of phantom power from the mixer.Digital Audio Output (optional) AES/EBU-3 with word-clock• Mixed Output: Balanced, 1/4-in, stereo phone-jack for headphones, • recording devices or powered speakers
DS Series Hand-Held TransmittersHousing: Machined aluminum, quiet-coat finish• Capsule: Various dynamic and condenser. • RF Output: 1, 10, 25 or 50 mW, user selectable • Antenna: Internal• Telemetry: Battery status, mute status, channel, etc• Display: OLED• External Switch: Programmable On/off, on/on, on/mute, • on/logic muteBattery: Two Rechargeable NiMH included (or alkaline)• Rechargeable Battery Life: ~8 hours per charge, typical • @ 1mWRF Frequency Stability: < 5 ppm•
MIC OUTPUTS
IN
AES3IN
50-60 Hz 100-240 VAC ANTENNA A1234
ETHERNET WORD CLOCKANTENNA B RS232-GPIO5678
Mfgr: Sabine, Inc., Alachua, FL.DS8800 Made In USATM
IN
OUT
OUT
OUT.315A
T-250V
MIC OUTPUTS
AES3
50-60 Hz 100-240 VAC ANTENNA AETHERNET WORD CLOCKANTENNA B RS232-GPIO
4G- +
3G- +
2G- +
1G- +
8G- +
7G- +
6G- +
5G- +
Mfgr: Sabine, Inc., Alachua, FL.DS8800 Made In USATM
OUT
IN
IN
OUT
OUT
IN
.315A
T-250V
MIC OUTPUTS
AES3
50-60 Hz 100-240 VAC ANTENNA AETHERNET WORD CLOCKANTENNA B RS232-GPIO
4G- +
3G- +
2G- +
1G- +
8G- +
7G- +
6G- +
5G- +
Mfgr: Sabine, Inc., Alachua, FL.DS8800 Made In USATM
OUT
IN
IN
OUT
OUT
IN
.315A
T-250V
IN
AES3IN
50-60 Hz 100-240 VAC ANTENNA AETHERNET WORD CLOCKANTENNA B RS232-GPIO
Mfgr: Sabine, Inc., Alachua, FL. Made In USATM
IN
OUT
OUT
OUT
MIC OUTPUTS1234
DS8400
.315A
T-250V
AES3
50-60 Hz 100-240 VAC ANTENNA AETHERNET WORD CLOCKANTENNA B RS232-GPIO
4G- +
3G- +
2G- +
1G- +
Mfgr: Sabine, Inc., Alachua, FL. Made In USATM
OUT
IN
IN
OUT
OUT
INDS8400
MIC OUTPUTS
.315A
T-250V
DS Series Belt Pack TransmitterHousing: Cast aluminum• RF Output: 1, 10, 25 or 50 mW, user selectable• Antenna: External, field replaceable• Telemetry: Battery status, mute Status, channel, etc• Display: OLED• External Switch: Programmable On/off, on/on, on/• mute, on/logic muteBattery: Two Rechargeable NiMH included (or • alkaline)Rechargeable Battery Life: ~8 hours per charge, • typical @ 1mWRF Frequency Stability: < 5 ppm• Mic input impedance: 47 K Ohms• Mic bias: 3V• Mic connector: TA4•
Receiver 4 channel front
Receiver 8 channel XLR back
Receiver 8 channel Euro-block back
Receiver 4 channel XLR back
Receiver 4 channel Euro-block back
Serial Interface: USB, RS232 & Ethernet• GPIO Interface: Programmable• Computer Software: System control, monitor, scan• Programing Display: OLED• Maximum Un-distorted • Sine Wave Output: +4dBuAntenna Distribution: Built-in. Attach up to 64 channels to one pair of • antennas Power input rating: 100 – 240 VAC 50/60 Hz 15WFuse: 250V SLOW BLOW 320mA• Operating Temperature: 0 - 50 degrees Celsius ambient temperature • (32-129 degrees F)Dimention: 1-U rack-mount, 19 x 1.75 x 6.5 inches (48 x 4.4 x 16.5cm)•
DS Series Receivers
Specifications
Sacom l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001
Architect’s and Engineer’s Specifications:Sacom DS8000 Series Digital Wireless SystemThe wireless system shall be based on 24-bit, 48 KHz, digital audio RF technology and operate in the frequency bands between 902 - 928 MHz, 710-740 MHz , or 606-630 MHz, with the specific range being dependent on the user’s local. The system shall provide a 256-bit encryption algorithm which conforms to the US Government AES (FIPS PUB 197) specifications.The receiver shall be modular in design with up to eight (8) modules per receiver. Up to 64 receiver channels must operate with one pair of antennas without an external antenna distribution amp. Extension antennas must operate up to 50 meters from the receiver with RG58 (or equivalent) cable. Each module will have a user programmable, menu driven LCD showing, channel, name and battery run-time hours since the last recharge. All transmitters shall be powered by at least two (2) rechargeable NiMH or, at least two (2) 1.5V Alkaline AA cells and shall have a programmable on/off, on/on, on/mute, or on/logic mute power switch. Available transmitters shall include: a belt pack for use with lavaliere and headset microphones; a handheld microphone; a conference table-top microphone; and a podium gooseneck microphone. All transmitters will have an LED indicating that power is on. The receiver shall include an RF meter, a diversity indicator, an audio level meter, and a networking interface connector for computer control and monitoring. The receiver shall include a headphone output and a method to monitor to audio of each receiver channel individually or mixed together. The receiver shall have a volume control and an adjustable noise squelch control.System latency in stage mode shall not exceed 3 mSec. The system shall include a docking station for recharging batteries and remote control software. The firmware for both the transmitters and receivers shall be capable of being upgraded in the field via a USB connection.The system shall be the SACOM DS8000 Series Digital Wireless Microphone System.
DS Series Conference Table-top TransmitterHousing: ABS• Mic - Internal• RF Output: 1, 10, 25 or 50 mW, user • selectableAntenna: Internal• Button: Press to talk, press to mute (or • logic mute), toggle on/offTelemetry: Battery status, mute Status, • channel, etcDisplay: None• External Switch: Programmable On/off, on/on• Battery: Two rechargeable AA NiMH include (or Alkaline)• Rechargeable Battery Life: ~8 hours per charge, typical @ 1mW• RF Frequency Stability: < 5 ppm•
DS Series Charging DockHousing: ABS• Power: Power suppy unit• Dimensions: 13.25 x 5.75 in.•
Specifications (continued)
DS8000 Series
DS Series Podium Gooseneck TransmitterHousing: Zinc and ABS• Capsules: Condenser - Omni, Cardioid or • Super-CardioidGooseneck lengths: Various• RF Output: 1, 10, 25 or 50 mW, user • selectableAntenna: Internal• Button: Press to talk, press to mute (or • logic mute), toggle on/offTelemetry: Battery status, mute Status, • channel, etcDisplay: None• External Switch: Programmable On/off, on/on• Battery: Four rechargeable AA NiMH include (or Alkaline)• Rechargeable Battery Life: ~16 hours per charge, typical @ 1mW• RF Frequency Stability: < 5 ppm•
Digital Wireless Microphone Systems
Specifications
DS Series Extension AntennasChoose ceiling mount or mic-stand mount • 130 degree reception pattern• Fixed gain, 915MHz: 15 dB• Phantom-powered from the receiver• Dimensions: 5.8”(dia) x 1.125”(d) • (14.8 x 2.9 cm)Weight: .55 lbs. (.24 kg) •
Sacom l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001
Digital Wireless Microphone Systems
Specifications
DS80-H13 Transducer Type: DynamicOEM: Audix*Frequency Response: 50 Hz - 18 kHzPolar Pattern: HypercardioidSensitivity: 1.7 mV / Pa @ 1kCapsule Technology: VLM Type BOff Axis Rejection: > 25 dBMaximum SPL: >_ 144 dBPolarity: Positive pressure on diaphram produces positive voltage on pin 2 relative to pin 3 of output XLR connector
Architect’s and Engineer’s Specifications:Sacom DS80-H13The DS80-H13 microphone capsule shall be of the dynamic type and the polar pattern shall be hypercardioid.The capsule shall have a sensitivity of 2.5 mV / Pa at 1 kHz and sound pressure level >_ 144 dB. The capsule grill cap shall be steel wire mesh. The overall dimensions of the microphone capsule shall be 55mm in diamiter at the widest point of the grill and 70mm in length The capsule shall be the Sacom DS80-H13.
Sacom DS80-H13 Microphone CapsuleThe DS80-H13 is a dynamic vocal microphone capsule used for a wide variety of live, studio and broadcast applications. Known for it’s clear and accurate sound reproduction, resistance to feedback and the ability to handle very high sound pressure levels without distortion. The DS80-H13 is characterized with a tight and uniformly controlled hypercardioid plor pattern wich helps to isolate the vocals from the rest of the instruments on stage. With a wide frequency range of 50 Hz - 18 kHz, the DS80-H13 employs a very low mass diaphram for a clean natural sound with exceptional transient response.The DS80-H13 microphone capsule has a very tight pick -up pattern in order to eliminate sound from other instruments on stage from “bleeding” into the microphone. For best results, it is important to sing directly into the mic at close proximity (within 2 inches).
DS80-H HAnD-HElD MICROPHOnE CAPSUlESDS80• -H13: Audix OM3 Dynamic HeadDS80• -H15: Audix OM5 Dynamic HeadDS80• -H18: Sacom H18 Condenser Head
Specifications (continued)
DS8000 Series
DS80-H15 Transducer Type: DynamicOEM: Audix*Frequency Response: 48 Hz - 19 kHzPolar Pattern: HypercardioidSensitivity: 1.8 mV / Pa @ 1kCapsule Technology: VLM Type COff Axis Rejection: > 30 dBMaximum SPL: >_ 144 dBPolarity: Positive pressure on dia-phram produces positive voltage on pin 2 relative to pin 3 of output XLR connector
Architect’s and Engineer’s Specifications:Sabine DS80-H15The DS80-H15 microphone capsule shall be of the dynamic type and the polar pattern shall be hypercardioid.The capsule shall have a sensitivity of 1.8 mV / Pa at 1 kHz and sound pressure level >_ 144 dB. The capsule grill cap shall be steel wire mesh. The overall dimensions of the microphone capsule shall be 55mm in diamiter at the widest point of the grill and 70mm in length The capsule shall be the Sacom DS80-H15.
Sacom DS80-H15 Microphone CapsuleThe DS80-H15 is a dynamic vocal microphone capsule used for stage, studio and broadcast applications. Known for it’s clarity, resistance to feedback and the ability to handle sound pressures in excess of 144 dB without distortion. The DS80-H15 is characterized with an extremely tight and uniformly controlled hypercardioid plor pattern wich helps to isolate the vocals from the rest of the instruments on stage. With a wide frequency range of 48 Hz - 19 kHz, the DS800-H15 employs a very low mass diaphram for natural response, accurate sound reproduction, and exceptional transient responce.The DS80-H15 microphone capsule has an extremely tight pick -up pattern in order to eliminate sound from other instruments on stage from “bleeding” into the microphone. For best results, it is important to sing directly ito the mic at close proximity (within 2 inches).
Sacom l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001
Digital Wireless Microphone Systems
Specifications
Specifications (continued)
DS8000 Series
Sacom DS80-H18 Microphone CapsuleThe DS80-H18 is a condenser vocal microphone capsule used for stage, studio and broadcast applications. Known for it’s clarity and resistance to feedback it features a strong wire-mesh, spherical front grill that contains a highly effective wind and “pop” filter. The DS80-H18 provides excellent vocal or speech reproduction on lecterns and stages, and, it is a popular choice for use in public auditoriums, churches, convention halls, and, schools.
DS80-H18Transducer Type: CondenserFrequency Response: 60 Hz - 15 kHzPolar Pattern: UnidirectionalOpen Circuit Sensitivity: -46dB +/-3dB @ 1kSignal to noise ratio: above 57dB @ 1KHz (1Pa)
Architect’s and Engineer’s Specifications:Sabine DS80-H18The DS80-H18 microphone capsule shall be of the condenser type and the polar pattern shall be unidirectional. The capsule shall have an open circuit sensitivity of -46dB +/-3dB @ 1k. The capsule grill cap shall be steel wire mesh. The overall dimensions of the microphone capsule shall be 49mm in diamiter at the widest point of the grill and 76mm in length The capsule shall be the Sacom DS80-H18.
* See www.sacomusa.com for details**Company names, product names, and trademarks listed here are the property of their respective owners and are used only to identify evaluated microphones used to develop digital processing; they in no way imply association, endorsement, or approval by any named manufacturer.NOTE: SACOMTM and Mission-Critical AudioTM are trademarks of Sabine, Inc., Alachua, Florida USA. Made in USA
(SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE)
Sacom_DS8000_DataSheet_130702.indd
