ENTE

R OUR WORLD OF MACHINE TOOLS

2011 2011 CatalogueCataloguewww.harp.co.za

Machine Tools

Frank ThompsonCompany Chairman

Welcome to our world of Machine Tools

CHAIRMANS REPORT

Shamus ThompsonManaging Director

John ThompsonSales Director

Kelly McCallumService Manager

Heather McCamlieAdmin. Manager

Lizette HolmesBookeeper

Desiree DanielsReceptionist

Ryan RipleyService Engineer

Kleinbooi MalopeElectrical Engineer

Roberto TalamontiMechanical Engineer

Brendan LapageService Engineer

Ronnie MakhubelaElectrical Engineer

Pieter SwiegersMechanical Engineer The Workshop Team

Harp Machine Tools, again saw a down turn in the economy in 2010, 10% less turnover than 2009. We are now 45% down in turnover, but with cuts everywhere in our expenses, we got through and everyone still has a job, which I think is a great achievement in itself. So we go into 2011 with high hopes for a better year.

The reasons we did so well in these hard times were: 1. Our service is the best.2. Our spares department is the best.3. Our mechanical and electrical service engineers are the best.4. Ours sales and admin staff are the best. 5. Harp Machine Tools are at your beck and call.

We all worked harder like I said we had to, and we did get through with fl ying colours. I would like to congratulate all who work at Harp Machine Tools and ask them to give it their best in 2011. I am sure we will see this economy grow in the next year or so.

In signing off , we would like to thank all our customers old and new, for their valued support last year. We look forward to your support this year. You will certainly get ours!!

All the best, health and prosperity.

Introduction ............................................................................................................................................................................................................................. Page 1 & 2Harp SMTCL CNC Slant Bed Lathes ........................................................................................................................................................................... Page 3Kingrich CNC Lathes KR-TC Model ............................................................................................................................................................................. Page 4Kingrich CNC Lathes KR-L Model ................................................................................................................................................................................ Page 5Kingrich CNC Lathes KR-BL Model ............................................................................................................................................................................. Page 6Kingrich Vertical Machining Centres Mini Mill .................................................................................................................................................... Page 7Kingrich Vertical Machining Centres KR-MF & ML Model ............................................................................................................................ Page 8Harp SMTCL CNC C-Frame Vertical Machining Centres ............................................................................................................................... Page 9Harp SMTCL CNC Horizontal Boring & Machining Centre ......................................................................................................................... Page 10Harp SMTCL CNC Bridge Type Vertical Mills ......................................................................................................................................................... Page 11Harp SMTCL Large CNC Vertical Boring Mills ..................................................................................................................................................... Page 12Harp SMTCL CNC Horizontal Boring Mills ............................................................................................................................................................. Page 13Harp SMTCL CNC Floor Type Horizontal Boring Mills .................................................................................................................................... Page 14Harp Tumac CNC Hydraulic Guillotines .................................................................................................................................................................. Page 15 & 16Harp Tumac CNC Hydraulic Pressbrakes ................................................................................................................................................................ Page 17 & 18Harp SMTCL Centre Lathes ............................................................................................................................................................................................. Page 19 & 20Kingrich Bed Type Milling Machines ........................................................................................................................................................................ Page 21Kingrich Turret Type Milling Machines ................................................................................................................................................................... Page 22Harp SMTCL Table Type Horizontal Boring Mills ................................................................................................................................................ Page 23Harp SMTCL Floor Type Horizontal Boring Mills ................................................................................................................................................ Page 24Harp Waytrain Fully Automatic Bandsaws ............................................................................................................................................................ Page 25Harp Waytrain Horizontal Bandsaws ........................................................................................................................................................................ Page 26Harp SMTCL Radial Drilling Machines ...................................................................................................................................................................... Page 27Sahinler Universal Ironworkers ..................................................................................................................................................................................... Page 28Sahinler Section & Pipe Bending Machines ......................................................................................................................................................... Page 29Sahinler Hydraulic Section & Pipe Bending Machines .................................................................................................................................. Page 30Sahinler 3 Rolls Hydraulic Plate Bending Machines ........................................................................................................................................ Page 31Sahinler 4 Rolls Hydraulic Plate Bending Machines ........................................................................................................................................ Page 32Sahinler 3 Rolls Motorized & Manual Plate Bending Machines ............................................................................................................... Page 33Sahinler Bordering & Trimming Machines ............................................................................................................................................................ Page 34Harp Baykal Industrial Plasma Cutting Machines ............................................................................................................................................. Page 35Used Butler Elgamill Bed Type Mills .......................................................................................................................................................................... Page 36Generators ................................................................................................................................................................................................................................ Page 36Used Webster & Bennett Vertical Boring Mills ................................................................................................................................................... Page 37 & 38Accessories .............................................................................................................................................................................................................................. Page 39 & 40

Index

Harp is the exclusive South African importer for Shenyang Machine Tools (Group) Co., Ltd. (SMTCL) of Shenyang - China. SMTCL is the largest producer of machine tools in the world, with a total production of over 86 000 machines, of which more than 20 000 were CNC machines. With a new state of the art 600 000 square meter manufacturing facility, SMTCL produces a complete range of high quality CNC and conventional machine tools for the world market.

There are few metal components in machines fabricated today which do not rely on machine tools, whether cue sticks, table legs or camshafts, SMTCL products can satisfy all your metal machining requirements. Shenyang Machine Tool CO. Ltd (SMTCL) is a premier conventional lathe and CNC lathe manufacturer in China. Through their continued eff orts and over 15 years of experience. They now have the capacity of producing a wide range of machine tools, including conventional lathe, fl at bed CNC lathe, CNC boring milling machines, turret milling centre’s, horizontal machining centre’s, radial drilling machines and a lot more.

SMTCL precision machine tools are designed with many innovative features that provide outstanding performance, reliability and productivity to their customers. These are utilized in a wide variety of industries, such as Automotive, national defence and military aerospace and aviation, railway transportation and so on. Some of the uses of their products include, conventional lathes, used for turning internal, external and cylindrical surfaces: fl at bed CNC lathes, primarily used in machining surfaces of axes and discs, tapered surfaces, arc surfaces, threads and boring holes; milling and boring machining centre’s, designed for processing medium to large sizedwork pieces of various materials, pipe threading lathes ideally suited for machining of Metric and a Whitworth threads as well as taper threads.

At SMTCL, they have been dedicated to providing quality built, economically priced machine tools. To achieve this, they have taken a series of quality and cost control measures. In order to ensure their quality, they strictly manufacture their conventional lathes and fl at bed CNC lathes in accordance with the related ISO standards, utilize CAD and other computer-aided techniques and introduce advanced production and inspection equipment. In addition their partnerships with well known companies such as Sauter Company and Siemens AG further guarantee the performance of their machine tools. Moreover, they employ competent staff and off er them ongoing training, which helps improve their productivity and reduces their production costs. Their production costs are also greatly reduced through their use of mass production. As a result, they can provide conventional lathes and CNC Boring milling machines etc. at an aff ordable prices.

1

Kingrich Companies Industries LimitedEstablished in 1975, Kingrich Industries has evolved from a traditional knee-type mill manufacturer, into a bed-type mill and CNC mill producer. In the manufacture of precision milling machines, we have become one of the leaders in Taiwan through R & D, quality and dependability. Up to now over 32,000 Kingrich machines have been installed and operated around the world. Kingrich milling machines are well known for their precision, stability, durability and dependability. This reputation results from our strong commitment to quality. Since the company was established, we have been committed to manufacturing and providing the best possible machine tools to serve our customers. This philosophy has never changed.

Each Kingrich machine is highly reputed and built with the tradition of fi ne craftsmanship and performance excellence that provides higher quality machining. The use of top quality Meehanite cast iron on the machine structure ensures deformation-free service after years of operation. Kingrich is an ISO9000 certifi ed company and machines are CE certifi ed. These give added confi dence that each Kingrich machine will meet or exceed your requirements. Choose from a wide variety of models that meet the varied demands of today’s machining needs. You have fl exible choice of models but you only have once choice for quality excellence.

Sahinler MetalSahinler, established in 1953 as a family company, continues today to serve the industry with its 2 factories and 300 staff in 25.000m2 closed area. They are the leading manufacturer in Turkey for Plate Bending Machines, Profi le Bending Machines and Ironworkers. With new products under their production program, such as Cutting/Flanging Machines and Dish-end Making Machines, and a 175 Ton Ironworker, they aim to cover all the needs of our customers in all sheet metal related industries. They also have a range of 4R HSS Plate Rolls which has been improved to meet the demands of the new Wind Tower Sections.

Webster & Bennett International LimitedWebster & Bennett is a United Kingdom based manufacturer specialising in the production of vertical boring mills. They have been manufacturing top quality vertical borers since 1887 and are today still market leaders. At Harp Machine Tools, we have refurbished more than 440 used Webster & Bennett’s which have successfully been put back into production.

Harp Service & SparesIn 2008, we identifi ed a need to carry a full range of spares for the many new machines we were installing in the market. We custom built new stores for this purpose at the bottom of the showroom as we realised well stocked, well managed stores need ample room to set up and grow. In January 2009, Harp Service and Spares moved into their new space and began trading. Despite the dismal economic climate of 2009, we provided spares to many customers keeping their machines in production for as many hours as possible.

We stock a full range of Kingrich Spares, centre lathe, radial drill, press brake and guillotine spares. Items that we don’t carry in stock, we will source locally, have them manufactured, or air freight them in. We have also expanded our range of Webster and Bennett spares to include leadscrews and nuts, clutch plates, fi bre gears and many other parts.

Harp Service and Spares also supplies digital readouts and accessories for all types of metal working machines, and what we don’t have, we will source. Because, at Harp, we understand that down time is money lost, and we will continue to do all in our power to keep your machines running 24/7.

2

The HTC series of CNC slant bed lathes are designed for heavy metal cutting applications while maintaining exacting tolerances. Non-cutting time is minimized with high speed servo turret and rapid traverse rates.

They feature two speed geared headstocks that ensure optimal power over a wide range of speeds. Both series of turning centers have a 45 degree, one piece, heavily ribbed slant bed, hardened and ground box ways.

Extra wide guideway spans on both the X and Z axes, and anti-friction PTFE liners on the mated slides to ensure accuracy and prolong machine life.

Harp SMTCL Slant Bed CNC Turning Lathe HTC3260

3

Specifications: HTC2050 HTC3260 HTC50 HTC63 HTC80Chuck diameter 210mm 250mm 380mm 450mm 530mmMax. Swing over bed 450mm 500mm 600mm 810mm 1000mmMax. Cutting diameter 200mm 320mm 500mm 630mm 800mmMax. Cutting length 500mm 600mm 1000/1500/2500mm 1000/1500/3000/4000/6000mm 1000/1500/3000/4000/6000mm

Bar Capacity 37mm 47mm 57mm 80/100mm 100/120mmMax. travel of X-axis 170mm 165mm 270mm 447mm 531mmMax. travel of Z-axis 660mm 700mm 1030/1530/2530mm 1200/1700/3200/4200/6200mm 1200/1700/3200/4200/6200mm

Spindle bore Ø55mm Ø55mm Ø75mm Ø100mm(Ø125mm) Ø125mm(Ø140mm)Range of spindle speeds 45-4000Rpm 45-3000Rpm 30-2000Rpm 50-1800Rpm 50-1600RpmMain motor power 11/15KW 11/15KW 22/26KW 30/37KW 30/37KWRapid speed (X/Z) 16/20m/min 20/20m/min 16/20 m/min 8/10 m/min 8/10 m/minTool station 8 10 12 12 12Taper of quill 5MT 5MT 5MT 5MT 5MTQuill diameter of tailstock Ø80mm Ø80mm Ø140mm Ø160mm Ø160mmQuill travel of tailstock 100mm 100mm 160mm 120mm 120mmControl Fanuc Fanuc Fanuc Fanuc Fanuc

Harp SMTCL CNC Slant Bed Lathe

Standard Features

• 2 Speed geared headstock

• 12 Position turret for HTC models (8 or 12 position turret for HTC50)

• Chip conveyor

• Automatic pressurized metered lubrication system

• NSK bearings and THK ballscrews

• Programmable tailstock - Body and quill

• Leveling pads and bolts

• Set of tool holders

• Work light

• Parts list and electrical drawings

The Kingrich TC-200 / TC-400 CNC Turning Centre is engineered for speed, precision, and enhanced productivity. The R & D team used the most advanced design analysis software to construct these outstanding machines.

These machines are very reliable and ridged machines incorporating hardened box ways and a solid ribbed casting. These machines have oversized digital servo motors and automatic lubrication to slides and ballscrew for fast rapids.

The TC-200 comes standard with a hydraulic 6" 3 Jaw chuck, 10 station hydraulic turret and chip conveyor and programmable tailstock available as an option. The TC-400 comes standard with a hydraulic 10" 3 Jaw chuck, 12 station hydraulic turret and swarf conveyor and programmable tailstock available as an option.

Standard FeaturesKR-TC400

• Hydraulic 10" 3 Jaw chuck

• 12 Station servo turret

• Precision ground ballscrews

• Fully interlocked guards

• Automatic lubrication system

• Coolant system

• Electronic handwheel

• Swarf conveyor and bin

• Worklight

• Tool kits

Standard FeaturesKR-TC200

• Hydraulic 6" 3 Jaw chuck

• 10 Station servo turret

• Fully interlocked guards

• Automatic lubrication system

• Coolant system

• Electronic handwheel

• Swarf conveyor and bin

• Worklight

• Tool kits

4

Specifications: KR-TC200 KR-TC400Max. swing 400mm 600mmMax. turning diameter 220mm 400mmX Axis travel 180mm 275mmZ Axis travel 310mm 650mmSpindle nose A2-5 A2-8Max. spindle speeds 4500mm 3500mmSpindle bore 61mm 91mmBar capacity 52mm 78mmMax. cutting feed rate 10m/min 10m/minMax. rapid traverse rate 20m/min 20m/minNo. of tool disc diameter 330mm 410mmNo. of tool station 10 12Size of external turret tool 25mm 25mmControl Fanuc/Siemens Fanuc/Siemens

Kingrich CNC LatheKR-TC400

Kingrich CNC Lathe - KR-TC Model

The Kingrich precision CNC Lathe is the latest generation of Manual / CNC combination lathes, designed with the versatility to handle everything from precision small jobs to heavy-duty work. With easy to use conversational programming, this machine can handle many jobs much more effi ciently and more accurately than a manual machine. All Kingrich lathes adopt single ribbed casting. This single casting gives these lathes extreme weight and rigidity. The heavier and more rigid it is, the better its overall precision performance. Other signifi cant weight and rigidity valves come from the excessive “V33 and Flat” bed ways that provide a large bearing surface.

The headstock is built using only the highest quality gears and bearings, and the heavy tailstock boasts three clamping points. These all combine to make Kingrich Lathes the surest turning investment you’re ever likely to make. Each Kingrich lathe must pass rigorous inspection and tests through assembly to ensure optimum integrity of all components “Rigorous testing on headstock / Laser inspection / Ball bar testing”.

5

Specifications: KR-L300 KR-L360 KR-L480 KR-L555Swing over bed 300mm 360mm 480mm 555mmSwing in gap - - 700mm 780mmGap in front of faceplate - - 224mm 224mmSwing over cross slides 168mm 225mm 257mm 350mmCross slide travel 185mm 195mm 205mm 280mmDistance between centres 700mm 1000mm 1250mm 1000mmMax. cutting length 580mm 850mm 1100mm 850mmSpindle bore 42mm 52mm 80mm 104mmSpindle motor 7.5Hp 7.5Hp 10Hp 12.5HPSpindle speeds 100-3000rpm 50-4000rpm 25-2500rpm 30-1800rpmTailstock taper 4MT 4MT 5MT 5MTBed Width 290mm 300mm 370mm 370mmControl Fanuc/Siemens Fanuc/Siemens Fanuc/Siemens Fanuc/Siemens

StandardFeatures

• Precision ground ballscrews

• Fully interlocked guard

• Air assisted tailstock (Not L300)

• Automatic lubrication

• Coolant system

• Fixed steady

• Traveling steady

• Swarf tray

• Worklight

• Tool kits

Kingrich CNC LathesKR-L Model

Kingrich CNC Lathe KR-L555

Standard Features• Precision ground ballscrews

• Fully interlocked guard

• Air assisted tailstock

• Automatic lubrication

• Coolant system

• Fixed steady

• Traveling steady

• Swarf tray

• Worklight

• Tool kits

6

Specifications: KR-BL480 KR-BL555 KR-GL555Swing over bed 480mm 555mm 555mmSwing in gap 700mm 780mm 935mmGap in front of faceplate 224mm 224mm 300mmSwing over cross slides 257mm 350mm 350mmCross slide travel 205mm 280mm 380mmDistance between centres 2000mm 1750mm 3000mmMax. cutting length 1850mm 1600mm 2900mmSpindle bore 80mm 104mm 104mmSpindle motor 10hp 12.5hp 15hpSpindle speeds 25-2500Rpm 30-1800Rpm 30-1800RpmTailstock taper 5MT 5MT 6MTBed Width 370mm 370mm 500mmControl Fanuc/Siemens Fanuc/Siemens Fanuc/Siemens

Kingrich CNC LathesKR-BL Model

The Kingrich precision CNC Lathe is the latest generation of Manual / CNC combination lathes, designed with the versatility to handle everything from precision small jobs to heavy-duty work. With easy to use conversational programming, this machine can handle many jobs much more effi ciently and more accurately than a manual machine.

All Kingrich lathes adopt single ribbed casting. This single casting gives these lathes extreme weight and rigidity. The heavier and more rigid it is, the better its overall precision performance. Other signifi cant weight and rigidity valves come from the excessive “V33 and Flat” bed ways that provide a large bearing surface.

The headstock is built using only the highest quality gears and bearings, and the heavy tailstock boasts three clamping points. These all combine to make Kingrich Lathes the surest turning investment you’re ever likely to make. Each Kingrich lathe must pass rigorous inspection and tests through assembly to ensure optimum integrity of all components “Rigorous testing on headstock/Laser inspection/ Ball bar testing”.

Kingrich CNC Lathe KR-BL480

7

Standard Features - 710• Spindle air blast

• 16 Carousel type ATC

• Air purge system

• Automatic lubrication system

• Steel concertina guards on all axes

• Fully enclosed guards

• Coolant system

• Electronic handwheel

• Automatic power off function

• Worklight

• Tool kits

Standard Features - 560• Spindle air blast

• 12 Carousel type ATC

• Three axis AC servo motor

• Three axis precision ground ballscrew

• Automatic lubrication system

• Solid square slideway construction

• S teel slideway covers on all axes

• Fully enclosed guards

• Coolant system

• Electronic handwheel

• Automatic power off function

• Rigid Induction hardened slides

• Worklight

• Tool kits

Standard Features - 450• Spindle air blast

• 12 Carousel type ATC

• Three axis AC servo motor

• Three axis precision ground ballscrew

• Automatic lubrication system

• Solid square slideway construction

• Steel slideway covers on all axes

• Fully enclosed guards

• Coolant system

• Electronic handwheel

• Automatic power off function

• Rigid Induction hardened slides

• Worklight

• Tool kits

Kingrich Vertical Machining Centre KR-MF710

Kingrich Vertical Machining Centre Mini Mill 560

Kingrich Vertical Machining Centre Mini Mill 450

Specifications: Mini Mill 450 Mini Mill 560 KR-MF710Table size 530x320mm 610x370mm 760x430mmX Travel 450mm 560mm 710mmY Travel 315mm 400mm 450mmZ Travel 400mm 500mm 510mmSpindle nose to table 100-492mm 100-600mm 100-610mmRapid feed XYZ axis 24m/min 20 m/min 20 m/minMax. table load 230kg 320kg 350kgSpindle speed 60-8000Rpm 60-8000Rpm 60-8000RpmSpindle motor 10hp 10hp 10hpSpindle taper BT40 BT40 BT40Tool magazine capacity 12 (Carousel) 12 (Carousel) 16 (Carousel)Tool change time (T-T) 6 Sec 6 Sec 6 SecWay Box way Box way Box wayControl Fanuc/Siemens Fanuc/Siemens Fanuc/Siemens

Kingrich Vertical Machining CentresMini Mill

8

Kingrich Vertical Machining Centre KR-ML1020HS

Kingrich Vertical Machining Centre KR-ML1250

Specifications: KR-MF1020 KR-ML1020HS KR-ML1250Table size 1120x500mm 1200x600mm 1280x600mmx Travel 1020mm 1020mm 1250mmY Travel 520mm 610mm 620mmZ Travel 540mm 620mm 690mmSpindle nose to table 120-660mm 140-760mm 100-790mmRapid feed XYZ axis 20,000mm/min 43,000mm/min 30,000mm/minMax. table load 800kg 800kg 800kgSpindle speed 60-8000Rpm 12000Rpm 60-8000RpmSpindle motor 15hp 15hp 15hpSpindle taper BT40 BT40 BT40Tool magazine capacity 20 (Carousel Type) 24 (Arm Type) 24 (Arm Type)Tool change time (T-T) 6 Sec 2 Sec 2.5 SecWay Box way Roller Linear Way Linear WayControl Fanuc/Siemens Fanuc/Siemens Fanuc/Siemens

Kingrich Vertical Machining CentresKR-MF & ML Models

Standard Feature - ML1250• 8000Rpm spindle• Spindle air blast• 24 Tool arm type ATC • Three axis AC servo motor • Three axis precision ground ballscrew• Automatic lubrication system• Linear way on three axes • Steel slideway covers on all axes• Fully enclosed guards• Coolant system• Chip fl ush system• Electronic handwheel• Automatic power off function• Worklight• Tool kits

Standard Features - MF1020• 8000Rpm spindle• Spindle air blast• 20 Tool arm type ATC • Three axis AC servo motor • Three axis precision ground ballscrew• Automatic lubrication system• Solid square slideway construction • Steel slideway covers on all axes• Fully enclosed guards• Coolant system• Chip fl ush system• Electronic handwheel• Automatic power off function• Worklight• Tool kits

Standard Features - ML1020• 12000Rpm spindle• Spindle oil cooler• Spindle air blast• Fast 24 Tool arm type ATC (2 sec. T-T)• Three axis AC servo motor • Three axis precision ground ballscrew• Automatic lubrication system• Roller linear way on three axes • Steel slideway covers on all axes• Fully enclosed guards• High pressure coolant system• High pressure chip fl ush system• Electronic handwheel• Swarf conveyor• Automatic power off function• Worklight• Tool kits

Kingrich Vertical Machining Centre KR-MF1020

9

The VMC- B Series machines are made with an innovative Frame Structure with high rigidity. Main components such as bed, columns, etc., all incorporate cast iron with excellent vibration dampening and thermal characteristics for excellent rigidity and accuracy of machining. The main parts such as bed, columns, etc. all adopt thermally symmetrical design and box-shape structure, which ensures machining in high speed, high effi ciency and high accuracy. Also, user friendly operation interface is easy to use. Direct mounted motor on the spindle ensures quicker start, higher running speed (8000Rpm), reduced footprint and space requirements, easier operation and maintenance. Spiral chip conveyors on either side of the bed promote effi cient chip removal.

Harp SMTCL CNC C-Frame VerticalMachining Centres

Specification: VMC700B VMC850B VMC1000B VMC1100B VMC1300B VMC1600B VMC2100BTable size 800x420mm 1000x500mm 1200x500mm 1300x610mm 1400x700mm 1700x800mm 2200x800mmTable load capacity 600kg 600kg 600kg 1000kg 1000kg 2000kg 3000kgX Axis travel 700mm 850mm 1000mm 1100mm 1300mm 1600mm 2100mmY Axis travel 440mm 560mm 610mm 610mm 700mm 800mm 800mmZ Axis travel 530mm 650mm 650mm 650mm 700mm 800mm 800mmSpindle taper BT40 BT40 BT40/BT50 BT40/BT50 BT40/BT50 BT50 BT50Spindle speeds 8000Rpm 8000Rpm 8000/6000Rpm 8000/6000Rpm 8000/6000Rpm 6000Rpm 6000RpmSpindle motor 7.5/11kW 11/15kW 11/15kW 11/15kW 11/15kW 15/18.5kW 15/18.5kWFeed Speeds 20m/min 20m/min 20m/min 20m/min 10m/min 10m/min 10m/minTool Qty 24 Pockets 24 Pockets 24/20 Pockets 24/20 Pockets 24/20 Pockets 20 Pockets 20 PocketsTool Change Time 2.8 Sec 3.5 Sec 3.5 Sec 3.5 Sec 3.5 Sec 3.5 Sec 3.5 SecX & Y Axis rapid traverse 32m/min 32m/min 32m/min 32m/min 24m/min 24m/min 18m/minZ Axis rapid traverse 32m/min 30m/min 30m/min 20m/min 20m/min 20m/min 18m/minMachine weight 5000kg 6000kg 6200kg 7000kg 10000kg 12500kg 16000kgControl Fanuc Fanuc Fanuc Fanuc Fanuc Fanuc Fanuc

Harp SMTCL Vertical Machining Centre VMC1300BStandard Features• 3 Axis Ballscrews• Stainless steel guideway protection• Water tank• Lubrication system• Pneumatic system• Air gun• Illuminating lamp• 3 Colour alarm lamp• Cool-heat exchanger• Fanuc CNC control• Ethernet function

10

Harp SMTCL CNC Horizontal Boring& Machining Centre

The HMC series of CNC horizontal boring and machining centres are ideally suited for the machining of all kinds of prismatic workpieces and two dimensional or three dimensional curved surfaces. These machines are widely used in general manufacturing, automotive, shipping, textile and press mechanism, and the agriculture industries.

The spindle of these machining centres is driven by a two speed spindle ground transmission to increase spindle torque. The spindle incorporates precision bearings to provide higher spindle speeds with excellent rigidity and accuracy with a longer tool life.

Machines with higher spindle speeds come equipped with a spindle oil chiller to minimize thermal expansion to the spindle. The HMC series are available with either an indexing rotary table or a full fourth axis (B) rotary worktable that has an angular encoder for direct measurement to ensure higher accuracy. These machines feature replaceable ground and hardened box type ways to ensure high stiff ness for heavier cuts, and linear roller pack with high rigidity for faster traverse. The double exchanging pallet system facilitates pallet auto-exchange, resulting in reduced assistant time and increased effi ciency.

Harp SMTCL Horizontal

Boring Machining Centre HMC50

Specifications: HMC40 HMC50 HMC60 HMC80 HMC100hsTable size 400x400mm 500x500mm 600x600mm 800x800mm 1000x1000mmNumber of pallets 2 2 1/2 1/2/8 2Pallet Change time (s) 8 8 26 45 45Table load cap. (Kg) 400kg 500kg 1200kg 2000kg 2000kgX Axis Travel 585mm 585mm 990mm 1300mm 1500mmY Axis Travel 635mm 635mm 838mm 990mm 1200mmZ Axis Travel 685mm 685mm 736mm 990mm 990mmB-axis (rotary table) 360deg/1 deg 360deg/1 deg 360deg/1 deg 360deg/1 deg 360deg/1 degSpindle axis to table 50-685mm 50-685mm 0-840mm 0-990mm 0-1200mmSpindle taper BT50 BT50 BT50 BT50 BT50Spindle Speeds 20-5000rpm 20-5000rpm 20-5000rpm 20-5000rpm 20-5000rpmRapid feeds XYZ Axis 24m/min 24m/min 24m/min 24m/min 24m/minSpindle motor 15/20hp 15/20hp 20/25hp 30/35hp 30/35hpTool magazine capacity 60 (40,90) 60 (40,90) 60 (40,90) 60 (40,90) 60 (40,90)Machine Weight 17.5 Tons 17.5 Tons 17/19.5 Tons 25.5 / 29 Tons 30.5 TonsControl Fanuc Fanuc Fanuc Fanuc Fanuc

11

The GMB series of CNC bridge mills are the heaviest machines in their class, making them exceptionally stable and perfectly suited for heavy production operation, while maintaining exacting tolerances for precision machining. The modular design of these machines allows them to be confi gured and customized to the demands and applications of the customer.

Specifications: GMB1016 GMB1020 GMB1225 GMB1230 GMB1620 GMB1630 GMB1640Table size 1600x1000mm 2000x1000mm 2500x1250mm 3000x1250mm 2000x1600mm 3000x1600mm 4000x1600mmDist. Between columbs 1250mm 1250mm 1450mm 1450mm 2100mm 2000mm 2100mmTable load capacity 3 Tons 3.5 Tons 5 Tons 6 Tons 8 Tons 10 Tons 12 TonsX Axis Travel 1600mm 2000mm 2500mm 3000mm 2200mm 3200mm 4200mmY Axis Travel 1000mm 1000mm 1250mm 1250mm 2300mm 2300mm 2300mmZ Axis Travel 600mm 600mm 750mm 750mm 1000mm 1000mm 1000mmSpindle taper BT50 BT50 BT50 BT50 BT50 BT50 BT50Spindle Speeds 40-6000rpm 40-6000rpm 40-6000rpm 40-6000rpm 40-6000rpm 40-6000rpm 40-6000rpmSpindle motor 18.5-22KW 18.5-22KW 18.5-22KW 18.5-22KW 30-37KW 30-37KW 30-37KWMachine Weight 22 Tons 26 Tons 31 Tons 33 Tons 40 Tons 46 Tons 51 Tons

Harp SMTCL CNC Bridge TypeVertical Mill

Standard Features

• Fanuc 18-Mi Control • Function for blowing air to spindle taper hole • Heidenhain glass scales on X, Y, and Z axes • Oil cooler for spindle unit and gearbox• Rigid tapping • Telescopic covers for X and Y Axis• Three axis encoder feedback system • Sheet metal machine enclosure• Pulse generator • Auto lubrication system• Footswitch for tool clamping/unclamping • Flood coolant system• Work area lamp and alarm lamp • Spray gun for chip removal• AC cooled electrical cabinet • Dual Helix chip conveyer • Two step gearbox with infi nitely variable speed control • Chain type chip conveyor & chips bucket

Harp SMTCL Bridge Mill GMB 160 x 20

Larger models available with greater travels (to X= 6000mm Y= 3200mm Z= 990mm and table load capacities (to 39 700lbs)

12

Specifications: GTC16090 GTC20090 GTC250110Working diamter 1250mm 1600mm 2000mmMax. Workpiece weight 6 Tons 8 Tons 10 TonsMax. Swing 1600mm 2000mm 2500mmMax. Turning diamter 1600mm 2000mm 2500mmMax. Turning height 1200mm 1600mm 2000mmRam head vertical travel 890mm 890mm 1200mmRam head horizontal travel -100+1600mm -150+2000mm -100+2800mm Ram cross section 200x200mm 220x220mm 250x250mmTool Magazine Positions 12 12 12Main motor 50/60hp 60/75hp 80/100hpMachine weight 20 Tons 26 Tons 50 Tons

Harp SMTCL Large CNC Vertical Boring Mills

The GTC series are vertical turning and milling centres which are designed to perform turning, milling and drilling functions in a single set up. These machines are suitable for both rough and fi nish machining of complicated parts such as motor shells, wheels, valve bodies, fl anges, large motor bases, pump bodies, or any components requiring centralized multi-process machining. These machines are based on Japaneseengineering and are constructed of high grade alloyed cast iron, normalized and stress relieved to ensure maximum rigidity and stability.

The single column construction features a symmetrically centered table, high precision NSK cylindrical roller bearings and NSK angular thrust bearings, ensuring heavy load capacity and high precision machining. The X and Z axes feature Heidenhain glass scales to ensure precision machining capability. A two-step planetary gear box delivers an impressive amount of torque for heavy duty machining, even at low table speeds.

Harp SMTCL Vertical Boring Mill - GTC10080

13

Specifications: PBC110 PBC130 PBC160Table size 1000x1250mm 1600x1800mm 2000x2500mmMax. load on the table 5000kg 10000kg 20000kgDiameter of spindle 110mm 130mm 160mmTaper of spindle MT5 MT5 MT5Spindle speed 10-2500r/min 10-3000r/min 10-1500r/minTransverse travel of table X 2000mm 2000mm 3500mmVertical travel of headstock Y 1500mm 1600mm 2500/3000mmLongitudinal travel of column Z 1200mm 1600mm 2000mmSpindle travel W 550mm 800mm 1000mmRapid speed XYZ 9m/min 9m/min 9m/minCapacity of tool magazine 40 40 40Power of main motor 17/22KW 20/30KW 37/51KWControl Siemens/Fanuc Siemens/Fanuc Siemens/Fanuc

PBC series machines are of a T-type layout and can provide for the control of Six axes: worktable transverse movement, column horizontal movement, worktable auto indexing and auto rotation, headstock vertical movement, spindle extension and optional NC facing head. Guideways of these machines incorporate alloy steel with complete hardening.

Imported rollers are used for side surface guiding and an angular encoder is supplied for direct measurement of the worktable. The high spindle torque is obtained via a two-step gearbox. The tool magazine and enclosure are available as options. Machines of this series are ideal for machining box type work pieces with multiple holes with a high degree of accuracy in regards to hole-to-hole distance.

Standard Features

• Centralized lubrication

• Helix conveyor

• Coolant system

• Air condition for electric cabinet

• Hydraulic oil tank

• Worklight

• RS232 Interface

• Triple-expansion pneumatic components

• MPG unit & bellow type protection for column

Harp SMTCL Horizontal Boring Mill PBC 130

Harp SMTCL CNC HorizontalBoring Mills

14

Harp SMTCL CNC Floor TypeHorizontal Boring Mills

his series of machines adopts the single-column, side-mounted headstock design. The column and saddle travel horizontally along the bed guideways. The headstock travels vertically on the column guideways. The spindle speed change incorporates an automatic gearbox to switch between hand and low ranges. Siements AC servo motor are installed on all axes. The X axis adopts double-motor, double-gear and rack drive technology, which greatly improves the driving force of the X-axis, and eliminates backlash much more eff ectively over traditional single-motor double-gear technology. The two motors move synchronously, and in slight opposition to each other in a way that is controlled electronically by the CNC and drives to remove backlash. The Y-axes incorporates the double motor and double ball-screw drive system. The Z and W axes adopt single pre-loaded ball-screw drive system. X, Y and Z (Ram) axes incorporate closed system constant fl ow hydrostatic guideways, which give high performance, low vibrations, and retain high precision over time

Harp SMTCL Floor Type Horizontal Boring Mill

FBC200

Standard Features

• Fanuc 18i-M Control and Fanuc 18i-MB (TH69)

• RS-232 Interface

• Heidenhain glass scale feedback on X & Y (TH62) Heidenhain glass scale feedback on X, Y & Z TH69)

• B-axis circular Heidenhain rotary scale (TH69)

• Automatic lubrication system

• Thru-spindle coolant

• Spindle oil chiller

• Hydraulic pump and tank unit

• Portable manual pulse generator

• Spiral type chip conveyor and chips bucket

• Chip guard for worktable

• Built in air to air heat exchanger for electrical cabinet

• 40 Tool ATC

Specificaitons: FBC110 FBC130 FBC160Spindle diameter Ø110mm Ø130mm Ø160mmSpindle taper BT50 BT50 BT50Spindle speeds 10-2500Rpm 10-2000Rpm 10-1500RpmX travel (column slide) 4000mm 4000mm 4000mmY travel (headstock vertical) 1500mm 1600mm -Cutting feed X, Y 1-6000mm/min 1-6000mm/min 1-6000mm/minMotor power 17/22.5kW 22/30kW 37/51kWTool capacity 40 40 40Machine weight 30,000kg 45,000kg 55,000kgControl Fanuc/Siemens Fanuc/Siemens Fanuc/Siemens

15

Specifications: QC12K-4*2500 QC12K-6*3200 QC12K-8*3200Max. cutting thickness 4mm 6mm 8mmMin. cutting thickness 0.5mm 0.5mm 0.5mmMax. cutting length 2500mm 3200mm 3200mmNo. load stroke 18 14 10Adjustable range of backgauge 20-600mm 20-600mm 20-600mmMain motor power 7.5KW 7.5KW 11KWWeight of machine 4200kg 7200kg 7800kgBack-gauge motor power 0.55KW 0.55KW 0.55KWDepth of the throat 140mm 140mm 140mmHeight of the working table 650mm 800mm 800mm

Standard Features

• Completely welded with steel plates. Firm & rigid construction.

• Sheet support

• Hydraulic overload protection

• Automatic adjustable back-gauge

• Automatic cutting time adjustment

• Foot pedal with emergency stop

• Hydraulic pump

• Squaring arm

• CNC control touch screen

• Automatic blade gap adjustment

• An error alarm function

Harp CNC Hydraulic Guillotines4mm to 8mm

Harp CNC Hydraulic Guillotine - 3200mm x 6mm

Harp CNC Hydraulic Guillotine range from: 4mm x 2500mm up to 20mm x 4000mm. Bigger sizes are available and can be quoted to suit customers requirements. The CNC Controlled Hydraulic Swing Beam Guillotines come with a LCD touch screen control. This control will adjust the back gauge automatically, adjust the blade gap automatically, and can store 100 programs consisting of 20 work steps.

Harp CNC Hydraulic Guillotine range from: 4mm x 2500mm up to 20mm x 4000mm. Bigger sizes are available and can be quoted to suit customers requirements. The CNC Controlled Hydraulic Swing Beam Guillotines come with a LCD touch screen control. This control will adjust the back gauge automatically, adjust the blade gap automatically, and can store 100 programs consisting of 20 work steps.

16

Specifications: QC12K-12*3200 QC12K-16*3200 QC12K-20*3200Max. cutting thickness 12mm 16mm 20mmMin. cutting thickness 1mm 1mm 1mmMax. cutting length 3200mm 3200mm 3200mmNo. load stroke 10 7 5Adjustable range of backgauge 20-800mm 20-800mm 20-800mmMain motor power 18.5KW 22KW 30KWWeight of machine 12500kg 16000kg 20000kgBack-gauge motor power 0.55KW 0.55KW 0.55KWDepth of the throat 140mm 170mm 170mmHeight of the working table 800mm 800mm 800mm

Harp CNC Hydraulic Guillotines12mm to 20mm

Standard Features

• Completely welded with steel plates. Firm & rigid construction.

• Sheet support

• Hydraulic overload protection

• Automatic adjustable back-gauge

• Automatic cutting time adjustment

• Foot pedal with emergency stop

• Hydraulic pump

• Squaring arm

• CNC control touch screen

• Automatic blade gap adjustment

• An error alarm function

Harp CNC Hydraulic Guillotine - 3200mm x 16mm

These CNC Hydraulic Pressbrakes are manufactured in Shanghai China. These machines have proven very popular with manufacturing and steel companies across the country.

Pressbrakes range from 63 tons x 2500mm to 400 tons x 4500mm. Bigger sizes are available and can be quoted to suit customers requirements. The 2 Axis touch screen system on the Hydraulic Pressbrake will calculate the bending angle, stroke of the ram, position of back gauge, and editing of machine programs in advance.

17

Standard Features

• The pressbrake adopts whole steel welded structure and has enough intensity and rigidity.

• Ram synchronization during the stroke is controlled by a mechanical torque synchro system.

• Ram stroke & back gauge can be adjusted by motor & manual adjustments & can be displayed by counters.

• A hydraulic system is used for the machine. A feeding valve is used to speed up the ram travel to save energy.

• The dies are made of carbon steel, which are good rigidity and durability.

• CNC touch screen control.

• Bottom multi V block & top gooseneck tooling.

• The machine is equipped with full safety guards and emergency stops.

• The CNC system can auto calculate the bending angle.

• The CNC system can realize alarm functions, which can avoid overloading & damage.

Harp CNC Hydraulic Pressbrake 3200mm x 125 Ton

Specifications: WC67K-63/2500 WC67K-80/2500 WC67K-125/3200Tonnage 63 Tons 80 Tons 125 TonsMax. bending length 2500mm 2500mm 3200mmDistance between columns 2080mm 2700mm 2700mmThroat depth 250mm 250mm 320mmTravel of back- gauge 600mm 600mm 600mmStoke adjustment of the ram 80mm 80mm 120mmNumber of stroke 8 time/min 8 time/min 8 time/minMotor power 5.5KW 7.5KW 7.5KW

Harp CNC Hydraulic Pressbrakes63t to 125t

These CNC Hydraulic Pressbrakes are manufactured in Shanghai China. These machines have proven very popular with manufacturing and steel companies across the country. Pressbrakes range from 63 tons x 2500mm to 400 tons x 4500mm. Bigger sizes are available and can be quoted to suit customers requirements.

The 2 Axis touch screen system on the Hydraulic Pressbrake will calculate the bending angle, stroke of the ram, position of back gauge, and editing of machine programs in advance.

18

Harp CNC Hydraulic Pressbrake 4500mm x 400Ton

Standard Features

• The pressbrake adopts whole steel welded structure and has enough intensity and rigidity.

• Ram synchronization during the stroke is controlled by a mechanical torque synchro system.

• Ram stroke & back gauge can be adjusted by motor & manual adjustments & can be displayed by counters.

• A hydraulic system is used for the machine. A feeding valve is used to speed up the ram travel to save energy.

• The dies are made of carbon steel, which are good rigidity and durability.

• CNC touch screen control.

• Bottom multi V block & top gooseneck tooling.

• The machine is equipped with full safety guards and emergency stops.

• The CNC system can auto calculate the bending angle.

• The CNC system can realize alarm functions, which can avoid overloading & damage.

Specifications: WC67K-160/4000 WC67K-250/4000 WC67K-400/4000Tonnage 160 Tons 250 Tons 400 TonsMax. bending length 4000mm 4000mm 4000mmDistance between columns 3150mm 3150mm 3280mmThroat depth 320mm 400mm 400mmTravel of back- gauge 600mm 600mm 600mmStoke adjustment of the ram 160mm 200mm 250mmNumber of stroke 8 time/min 8 time/min 6 time/minMotor power 11KW 18.5KW 37KW

Harp CNC Hydraulic Pressbrakes160t to 400t

19

Harp SMTCL Centre Lathes

Specifications: CA6236 CA6240B CA6250C CA6266CSwing over bed 360mm 400mm 500mm 660mmSwing over carriage 210mm 210mm 300mm 400mmSwing in gap 500mm 630mm 720mm 830mmWorkpiece length 1000mm 750mm-3000mm 750mm-3000mm 750mm-3000mmWidth of bed 320mm 400mm 400mm 400mm Spindle speeds 37-1600r/min 10-1400 r/min 14-1250r/min 14-1250r/minSpindle bore 53mm 80mm 104mm 104mmNo. longitudinal feeds 40 Kinds 64 kinds 64 kinds 64 kindsLong. feed Normal 0.04-1.60mm/rev 0.11-1.6mm/rev 0.11-1.6mm/rev 0.11-1.6mm/rev Long. feed Fine 0.028-0.11mm/rev 0.028-0.11mm/rev 0.028-0.11mm/rev 0.028-0.11mm/revLong. feed Coarse 1.76-6.4mm/rev 1.76-6.4mm/rev 1.76-6.4mm/rev 1.76-6.4mm/revMetric threads 0.5-10mm 1-192mm 1-192mm 1-192mm Whitworth threads 1/3 - 40tpi 1/2 - 24 t.p.I 1/2 - 24 t.p.I 1/2 - 24 t.p.ISpindle bore Taper MT4 MT5 MT5 MT5Main motor 4KW 7.5KW/10Hp 7.5KW/10Hp 7.5KW/10Hp

Standard Features

• 3 Jaw Chuck• 4 Jaw Chuck • Coolant

• Face plate• Fixed steady• Travelling steady• Quick change toolpost

The CA series of centre lathes are suitable for a wide range of turning applications. These lathes are constructed of high qualityMeehanite castings throughout. All bedways are induction hardened and precision ground on CNC way grinding machines.

With a wider bed than most common lathes, these machines have a greater degree of rigidity. The spindles are forged steel and are supported by precision NSK bearings.

The headstock features hardened and ground steel gears lubricated by an automatic force lubrication system. The Harp CA services engine lathes are engineered and manufactured for precision and maximum performance with standard features normally found as options on higher priced machines.

Harp SMTCL Centre Lathe CA6250 B x 2000mm

20

Specifications: CW6280C CW6293C CW62110C CW61160 CW61200Swing over bed 800mm 930mm 1100mm 1600mm 2000mmSwing over carriage 480mm 650mm 800mm 1200mm 1580mmWorkpiece length 1500-14000mm 1500-7000mm 1500-14000mm 3000-15000mm 3000-15000mmWidth of bed 600mm 600mm 600mm 1100mm 1100mmSwing in gap 1000mm 1100mm 1300mm None NoneSpindle bore 130mm 130mm 130mm 130mm 130mmSpindle speeds 18 kinds 18 kinds 18 kinds 21 kinds 21 kindsSpeed range 5.4-720 r/min 8.5-800 r/min 4.8-640 r/min 2-200 r/min 2-200 r/min No. of Longitudinal feeds 64 kinds 64 kinds 64 kinds 56 Kinds 56 KindsLongitudinal feeds 0.06-24.3mm/rev 0.05-24.3mm/rev 0.05-24.3mm/rev 0.1-12mm/rev 0.1-12mm/revMetric threads 1-240mm 1-240mm 1-240mm 1-120mm 1-120mmWhitworth threads 14-1 t.p.I 14-1 t.p.I 14-1 t.p.I 24-1/4 t.p.I 24-1/4 t.p.ITaper of tailstock MT5 MT5 MT5 80(metric) 80( metric)Main motor 11kw 11kw 11kw 22kw 22kwWeight of workpiece 2000kg 2000kg 2000kg 12000kg 12000kg

Harp SMTCL Heavy Duty Centre LathesHarp’s CW series heavy duty centre lathes are characterized by their powerful motors and high rigidity, making them exceptional for heavy turning operations. They are constructed of high quality Meehanite castings throughout. All bedways are induction hardened and precision ground on CNC way grinding machines.

The saddle guideways are coated with TSF wear-resistant material, providing smooth and effi cient movement. The spindles are forged steel and are supported by precision NSK bearings. The headstock features hardened and ground steel gears lubricated by an automatic force lubrication system. The CW series of heavy duty lathes come in bed lengths to handle workpieces from 750mm up to 15000mm.

These lathes are engineered and manufactured for precision and maximum performance with standard features normallyfound as options on higher priced machines.

Standard Features

• 3 Jaw Chuck• 4 Jaw Chuck • Face plate• Coolant

• Fixed steady• Travelling steady• Quick change tool post

Harp SMTCL Centre Lathe CW6280 B x 4000mm

Kingrich milling machines are well known for their precision, stability, durability and dependability. This reputation results from their strong commitment to quality. Since the company was established, they have been committed to manufacturing and providing the best possible machine tools to serve their customers. This philosophy has never changed.

21

Specifications KR-B3V KR-B4VTable size 1473x355mm 1930x355mmT-Slots (4) 15.9mm (4) 15.9mmLongitudinal travel X Axis 1050mm 1500mmCross travel Y Axis 480mm 600mmKnee travel Z Axis 480mm 480mmQuill Diameter 116mm 116mmQuill travel 140mm 140mmRapid feed rate 1900mm/min 1900mm/minSpindle motor 7.5hp 7.5hpSpindle speeds 70-3600Rpm 70-3600RpmSpindle Taper ISO40 ISO40Spindle nose to table surface 110-630mm 110-615mmHead tilt left to right 90 Degrees 90 Degrees

Standard Features

• American red turcite on X & Y axes

• Dovetail slideways on X axes

• Square slideways on Y & Z axes

• Hardened and ground X, Y & Z axes & table

• 1HP A.C. rapid vertical motor with break

• Frequency inverter control on longitudinal & cross feeds

• X & Y axes ballscrews

• Electric system

• X axis electrolytic dissociation

• Z axis air brake unit

• Steel slide cover on Y axis front

• Auto lubrication

• Roller type Y axis up-down chip guard

• Air power draw bar

• Coolant pump

Kingrich Bed Type Milling Machine

KR-B4V

Kingrich Bed Type Milling Machines

22

Each Kingrich milling machine is highly reputed and built with the tradition of fi ne craftsmanship and performance excellence that provides higher quality machining. The use of top quality Meehanite cast iron on the machine structure ensures deformation-free service after years of operation.

Standard FeaturesKR-V2000

• Dovetail slideways on X, Y, Z axes

• Hardened and ground table

• Chrome plating for X and Y axes

• X & Y power feed

• Electrics system

• Hand operated central lubrication

• Coolant pump

Standard FeaturesKR-V3000/ SL

• American red turcite on X & Y axes

• Dovetail slideways on X axes

• Square slideways on Y & Z axes

• Hardened and ground X, Y & Z axes & table

• 1.5HP A.C. rapid vertical motor

• X & Y power feed

• Electrics system

• Hand operated central lubrication

• Auto lubrication – KR-V3000SL

Kingrich Turret Type Milling Machine KR-V3000

Specifications: KR-V2000 KR-V3000 KR-V3000SLTable size 1270x254mm 1372x305mm 1473x305mmT-Slots (3) 15.9mm (3) 15.9mm (3) 15.9mmLongitudinal travel X Axis 812mm 863mm 1016mmCross travel Y Axis 400mm 400mm 400mmKnee travel Z Axis 406mm 406mm 406mmRam travel 450mm 450mm 450mmQuill travel 127mm 127mm 127mmSpindle motor 3hp 5hp 5hpSpindle speeds 60-4200Rpm 70-3600Rpm 70-3600RpmSpindle Taper R 8 ISO40 ISO40Spindle nose to table surface 50-457mm 50-457mm 50-457mmOver arm swivel 360 Degrees 360 Degrees 360 DegreesPower up & down on knee No Yes Yes

Kingrich Turret Type Milling Machines

Standard Features

• Built in pendant control

• Precision hardened and ground gears

• Precision hardened and ground ways

• Newall digital readout mounted in pendant control

• Fully automatic lubrication system

• Built in facing head

• Full stainless telescopic way covers

• Hydraulic clamping of headstock table and saddle

• Rapid traverse in all feed directions

• Integral outrigger support

Specifications: T(P)X6111B/3 T(P)X6113/2Boring spindle diameter 110mm 130mmSpindle taper ISO50 ISO50Spindle torque 1225N.m 3136N.mFacing head torque 1960N.m 4900N.mTraverse of boring spindle 600mm 900mmNumber of spindle speed 22 24Range of spindle speed 8-1000r/min 4-800r/minTravel of facing slide 180mm 250mmTable working surface 1250x1100mm 1800x1600mmPermissible load on table 3000kg 10000kgLongitudinal table travel 1400mm 2000mmCross table travel 1600mm 2000mmMain drive motor 7.5KW 15KW

Harp SMTCL Table Type Horizontal Boring Mill TPX6111B/3

23

The TPX series of table type horizontal boring mills are based on 50 years of machine tool building experience and the application of cutting edge technology. The design and functionality of these machines make them exceptional value. These boring mills are ideally suited for processing medium to large sized components with a high degree of machining accuracy. They feature Meehanite stress relieved castings for the base components for rigidity and stability even during heavy cutting operations.

The extra wide box ways are induction hardened and ground and the mated surfaces are coated with an anti-friction wear lining. They come with a built-in 360 degree rotary table for added versatility.

Harp SMTCL Table TypeHorizontal Boring Mill

24

The TPX series of fl oor type horizontal boring mills are modifi ed versions of the table type horizontal boring mills. These machines are ideally suited for machining large parts and can be used for drilling, counter-boring, boring, reaming, spot facing, threading and milling of fl at surfaces.

The beds of these machines can be extended to accommodate the machining of long pieces. Other modifi cations to meet the needs of the customers are also available.

Specifications: T(P)X6211x30 T(P)X6213x56Boring spindle diameter 110mm 130mmSpindle taper ISO50 ISO50Spindle torque 1225N.m 3136N.mMax. traverse of boring spindle 600mm 900mmNumber of spindle speed 22 24Range of spindle speed 8-1000r/min 4-8000r/minTravel of facing slide 180mm 250mmTravel of headstock 1600mm 1600mmTravel of main drive motor 3100mm 5650mmMain drive motor 7.5KW 15KW

Harp SMTCL Floor Type Horizontal Boring Mill

TPX6211

Standard Features

• Built-in pendant control

• Precision hardened and ground ways

• Fully automatic lubrication system

• Precision hardened and ground gears

• Integral outrigger support

Harp SMTCL Floor TypeHorizontal Boring Mill

Standard Features

• Control panel with compact human-machine interface

• Broken blade auto shut-off

• Dual vise shuttle system

• Hydraulic blade tension control device

• Motor inverter

• Automatic chip removal system

• PLC control system

• Slotted fi xed vice and shuttle vice

Waytrain Fully Automatic LX250, LX330 and LX460 series are completely in line with ISO-9001 quality and EC safety standards. The innovative human machine interface goes far beyond conventional controls with advanced features such as digital electronic control and linear encoder, appropriate for variable cut and feed settings and maintaining accuracy and speed. These machines have a control system that sets the length and quality of cuts, it also displays blade speed and is error indicator coded. The interface is combined with standard controls giving the user full operation of the machine.

Incorrect blade tension will automatically shut the machine off . Auto shut off prevents harm or injury to the machine or the operator. The machines are equipped with an automatic hydraulic shuttle and fi xed vise system. A slotted vise jaw on the fi xed vise allows for three section clamping and use of shuttle vice.

25

Harp Waytrain Fully Automatic Bandsaws

Harp Waytrain Fully Automatic

BandsawLX-330

Specifications: LX-250 LX-330 LX-460Cutting capacity - Round 250mm 330mm 460mmCutting capacity - Rectangle 250x300mm 330x330mm 460x355mmBlade size 27x0.9x3505mm 34x1.1x4100mm 41x1.3x4770mmBlade speeds 50Hz (16-66m/min) 50Hz (20-71m/min) 50Hz (15-61m/min)

60Hz (20-80m/min) 60Hz (25-85m/min) 60Hz (18-74m/min)Main motor 3hp 5hp 7.5hpHydraulic motor 1hp 1hp 2hpCoolant motor 1/6hp 1/6hp 1/4hpHydraulic tank 30L 40L 40LCoolant tank 40L 60L 120LLoad Capacity 1500kg 1750kg 2500kgRoller stand loading capacity 1000kg 1250kg 2000kgMinimum residual work length 50mm 50mm 130mmBundle Cutting (W x H) 150-250x100-150mm 150-250x120-180mm 200-300x150-200mmCut off length Over 10mm Over 10mm Over 10mmNumber of set cuts 1-9999 1-9999 1-9999Feed stroke 400mmx9 Times 400mmx9 Times 400mmx9 TimesMinimum no material detecting 50mm 50mm 50mmTable height 750mm 760mm 790mmMachine weight 1430kg / 1570kg 1700kg / 1850kg 2280kg / 2550kg

26

The Waytrain Horizontal Bandsaws are manufactured in Taiwan. Waytrain, which was founded in 1983, is a company well known for producing high quality machines. Sizes range from 180mm diameter cutting capacity, up to 330mm diameter. Rigidly constructed, with great attention to detail, these saws are a must for all engineering companies. We have four sizes in stock 180mm, 230mm, 250mm and 330mm.

All units are supplied with a 380v/3/50, blades are standard sizes for each model and spares are available on request. Based on the excellent design, reasonable prices and full scale global sales, Harp Machine Tools have established a brilliant business image in the industry. Quality and aff ordability are key features of this machine.

Harp Waytrain Horizontal Bandsaws

Specifications: UE - 712A1 UE - 916A UE - 250A UE - 330ACapacity 90 deg - Round 180mm 225mm 250mm 330mmCapacity 90 deg - Rectangle 280x180mm 345x225mm 415x250mm 480x330mm

300x65mm 400x35mm 450x200mm 530x225mmCapacity 45 deg - Round 110mm 165mm 190mm 255mmCapacity 45 deg - Rectangle 180x110mm 225x165mm 250x190mm 280x255mmBlade size 19x0.9x2360mm 27x0.9x3035mm 27x0.9x3300mm 34x1.1x4100mmBlade speeds 23/33/45/65MPM (Belt) 25/75MPM (Belt) 25-75MPM (Variable) 28/40/56/78MPM (Belt)Motor 1HP 1 1/2HP 2HP 3HPNet Weight 130kg 285kg 320kg 600kg

Harp Waytrain Horizontal Bandsaw 330A

Harp’s series of radial drilling machines are made from high strength castings and alloy steel, heat treated to ensure quality and durabil-ity. Clamping and speed changes are controlled by a highly reliable hydraulic system.

These machines, equipped with 16 to 22 variable speed ranges and 9 to 16 feed rates, provide for economic and effi cient cutting. Mechanical and electrical controls are centralized on the headstock for fast and easy operations.

27

Harp SMTCL Radial Drilling Machines

Specifications: Z3032 x 10/1 Z3050 x 16/1 Z3063 x 20/1 Z3080 x 25Drilling Capacity 32mm 50mm 63mm 80mm Radius 1000mm 1600mm 2000mm 2500mmMax. height 1000mm 1220mm 1600mm 2000mmSpindle travel 280mm 315mm 400mm 450mmSpindle Taper 4MT 5MT 5MT 6MTNo. of spindle speeds 16 16 16 16Spindle speeds 32-2500r/min 25-2000r/min 20-1600r/min 16-1250r/minNo. of spindle feeds 8 16 16 16Range of spindle feeds 0.10-1.25r/min 0.04-3.20r/min 0.04-3.2r/min 0.04-3.2r/minBox table size 630x500mm 630x500mm 800x630mm 1000x800mmTravel of spindle head 850mm 1250mm 1550mm 2000mmPower of main motor 2.2KW 4KW 5.5KW 7.5KW

Harp SMTCL Radial Drilling Machine Z3050 x 16/1

Harp SMTCL Radial Drilling Machines

28

Specifications: HKM45 HKM60 HKM65 HKM85Power pressure 45 Ton 60 Ton 65 Ton 85 Ton Diameter X Max. thickness 22x15mm 28x15mm 26x20mm 33x20mmDiameter X Thickness 38x8mm 38x11mm 57x10mm 55x16mmStroke 50mm 55mm 55mm 80mmStroke count in (20mm) x 20 x 25 x 25 x 25Throat depth 175mm 220mm 305mm 355mmWorking height 935mm 955mm 1030mm 1080mmSteel bare shear round 30mm 40mm 45mm 50mmSteel bar shear square 25mm 35mm 45mm 50mmAngle section @ 90 Degree 100x100x10mm 120x120x12mm 120x120x12mm 150x150x15mmAngle section @ 45 Degree 70x6mm 80x8mm 70x10mm 80x8mmSheet Metal shear 200x15mm 200x20mm 300x20mm 380x20mmBlade length 316mm 317mm 380mm 482mmNotching thickness 8mm 10mm 10mm 13mmNotching width 35mm 42mm 45mm 52mmNotching depth 75mm 100mm 90mm 100mmMotor power 4kW 4kW 5.5kW 7.5kW

Harp Machine Tools’ new range of Hydraulic Steelworkers are hard working and robust. Punching shearing and notching are incorporated in these machines. All complete with a foot control for easy and safe operation.

The punch & dies are interchangeable and easy to change. By changing the blades on the shearing section you can cut U-I or T Sections. With the help of Special Z form blades you can cut 90° and 45° angle sections effi ciently. These machines are suitable for CE regulations and ISO 9001-2000 certifi cate.

Standard Features

• Five work stations punching, steel bar shearing, angle shear, sheet metal shear & notching

• Punch and die Ø 22

• Punch Holder

• Flat bar cutting blade

• Solid round - square cutting blade

• Angle shear

• Notching blade

• Centralized lubrication system

• C-Spanner

• Work light - HKM65 & HKM85

• Electrical back gauge - HKM65 & HKM85

Sahinler Ironworker HKM65

Sahinler Universal Ironworkers

29

Sahinler Section & Pipe Bending MachinesThese section & pipe bending machine are manufactured with a steel welded construction frame and hardened shafts. It can be oper-ated both horizontally or vertically to suit your needs.

Special FeaturesPK 35 F

• Two rolls driven by a gear system

• Rolls are hardened

• Roll shafts housed by bearings

• Horizontal & Vertical working position

• Special lateral angle guides

• Special rolls

• All kinds of pipe, angle, profi le, leg-in, leg-out angle rolls and special lateral guide rollers are available upon request

Specifications: PK30F / 30S PK35-F PK40Shaft diameters Ø 30mm Ø 50mm Ø 40mmLower rolls diameters Ø 118mm Ø 155mm Ø 148mmTop roll diameter Ø 148mm Ø 155mm Ø 138mmWorking speed 3-6 m/min 4.5 m/min 5 m/minMotor power 0.7-0.85kW 1.5kW 2.2kWDimensions (LxWxH) 650x500x1400mm 750x900x1355mm 850x900x1470mmWeight 215kg 390kg 520kg

Sahinler Section & Pipe Bending Machine PK 35F

Specifications: HPK50 HPK60 HPK65 HPK80 HPK100Upper Roll Shaft - - Ø 60mm Ø 80mm -Bottom Roll Shaft - - Ø 50mm Ø 70mm -Roll Diamter - - Ø 180mm Ø 245mm Ø 315mmShaft diameters Ø 50mm Ø 60mm - - Ø 100mmLower rolls diameters Ø 162mm Ø 215mm - - -Top roll diameter Ø 152mm Ø 215mm - - -Working speed 4.5 m/min 4 m/min 5 m/min 6 m/min 7 m/minMotor power 0.75kW 1.5kW 3kW 4kW 7.5kWDimensions (LxWxH) 810x950x1500mm 830x1140x1650mm 1200x850x1200mm 1450x1000x1400mm 1465x2000x1700mmWeight 510kg 860kg 1000kg 1700kg 3650kg

30

These Hydraulic section & Pipe bending machines are manufactured with a steel welded construction frame and hardened shafts. It can be operated both horizontally or vertically to suit your needs.

All models are complete with a brake motor and a mobile control panel for easy and safe operation. These machines are suitable for CE regulations and ISO 9001-2000 certifi cate.

Sahinler Hydraulic Section & Pipe Bending Machine HPK50

Standard Features

• Steel welded construction frame

• 3 Rolls are powered

• Hardened shafts

• Top roll hydraulic movable

• Horizontal and vertical working position

• Guide rolls

• Brake motor

• Mobile control panel

• Pipe/Tube bending rolls

• Profi le bending rolls

• Angle bending rolls

Sahinler Hydraulic Section & Pipe Bending Machines

31

Harp Machine Tools new addition has been the Sahinler range of machines. Established in 1953 this Turkish company is well known globally for producing high quality Plate working machines. The plate rolls are hydraulically operated and are suitable for rolling a varie-ty of materials. With hydraulic drop-end for easy removal or rolled workpiece. Other features include induction hardened rolls, hydraulic balancing and a mobile control panel. These machines are suitable for CE regulations and ISO 9001-2000 certifi cate.

Specifiactions: 3R HS 30-210 3R HS 30-240 3R HS 30-280 3R HS 30-300Min. Diameter = top roll Ø x 5Length 3100mm 3100mm 3100mm 3100mmWithout pre-bending 6mm 8mm 10mm 13mmWith pre-bending 4mm 6mm 8mm 10mmMin. Diameter = top roll Ø x 1.5Without pre-bending 4mm 6mm 8mm 10mmWith pre-bending 3mm 4mm 6mm 8mmTop Roll Ø 210mm 240mm 280mm 300mmBottom rolls Ø 190mm 220mm 260mm 280mmmotor power 7.5kW 7.5kW 11kW 11kWWorking speed 5 m/min 5 m/min 5 m/min 5 m/minMachine dimensions 3700x1100x1250mm 4300x1250x1350mm 4400x1250x1500mm 4950x1420x1680mmWeight 5205kg 6600kg 8370kg 9900kg

Standard Features

• Plate bending capacities are given for 24kg/mm2 plate yielding strength

• Suitable for light and medium plates, aluminum or stainless steel

• Ferrules in full circle or varying radiuses can be done easily

• Lateral rolls move with hydraulic pistons

• Overload protection / All rolls are powered by hydromotor and planetary gearbox

• Hydraulic drop-end for easy removal of fi nished ferrule

• Digital Readout

• Induction hardened, hot rolled SAE 1050 (CK 45) steel device

• Hydraulic balancing system

Sahinler 3 Plate Hydraulic Plate Bending Machine 3R HS 40-240

Sahinler 3 RollsHydraulic Plate Bending Machines

32

Harp Machine Tools new addition has been the Sahinler range of machines. Established in 1953 this Turkish company is well known globally for producing high quality Plate working machines. The plate rolls are hydraulically operated and are suitable for rolling a variety of materials. With hydraulic drop-end for easy removal or rolled workpiece. Other features include induction hardened rolls, hydraulic balancing and a mobile control panel. These machines are suitable for CE regulations and ISO 9001-2000 certifi cate.

Sahinler 4 Plate Hydraulic Plate Bending Machine 4 HSS 30-245

Sahinler 4 RollsHydraulic Plate Bending Machines

Specifiactions: 4R HS 30-190 4R HS 30-220 4R HS 30-245 4R HS 30-260Min. Diameter = top roll Ø x 5Length 3100mm 3100mm 3100mm 3100mmWithout pre-bending 5mm 7mm 8mm 10mmWith pre-bending 3mm 5mm 6mm 8mmMin. Diameter = top roll Ø x 1.5Without pre-bending 3mm 5mm 6mm 8mmWith pre-bending 2mm 3mm 4mm 6mmCentral roll Ø 190mm 220mm 245mm 260mmSide rolls Ø 150mm 160mm 180mm 200mmMotor power 5.5kW 5.5kW 7.5kW 7.5kWWorking speed 1.5-6m/min 1.5-6m/min 1.5-6m/min 1.5-6m/minMachine dimensions 4500x1100x1300mm 4700x1200x1400mm 5000x1500x1500mm 5000x1600x1700mmWeight 4500kg 5500kg 6600kg 7480kg

33

Sahinler 3 RollsMotorized & Manual Plate Bending Machines

This mechanical model is designed for light to medium jobs. It is used in jobs up to 3mm thickness material. It is used in Aluminum bending, air conditioning channels, advertising panels and sheet metal covers. It ideal price makes it very attractive for small work-shops.

Specifiactions: RM 1050 x 90 RM 1270 x 90 RM 1550 x 90 RM 2050 x 95Working length 1050mm 1270mm 1550mm 2050mmBending capacity 3.0mm 2.5mm 2.0mm 1.5mmRoll diameter Ø 90mm 90mm 90mm 95mmRoll speed 6Rpm 6Rpm 6Rpm 6Rpmmotor power 1.1mm 1.1mm 1.5mm 1.5mmMachine dimensions 1630x700x1200mm 1850x700x1200mm 2130x700x1200mm 2630x700x1200mmWeight 480kg 520kg 580kg 715kg

Sahinler 3 Rolls Motorized & Manual Plate Bending Machine RM 1270 x 90

34

Sahinler Bordering & Trimming Machines

Specifications: IK 0.8 IK 1.2 IKMP 1.2Shaft length 110mm 140mm 140mmBeading Capacity 0.8mm 1.2mm 1.20mmRoll Diameter Ø52mm Ø62mm Ø62mmThroad Depth 80mm 100mm 100mmMotor Rotation - - 32RpmMotor Power - - 0.75kwDimentions (LxWxH) 380x180x380mm 560x220x500mm 900x450x1350nnWeight 30kg 50kg 110kg

Specifications: IBKS 2.5 IBKS 4.0Shaft length 250mm 300mmBeading Capacity 2.5mm 4mmRoll Diameter Ø96mm Ø126mmThroad Depth 160mm 200mmMotor Rotation 16Rpm 12RpmMotor Power 1.5kw 2.2kwDimentions (LxWxH) 1400x550x1120mm 1700x570x1200mmWeight 380kg 500kg

Sahinler Power Operated Bordering & Trimming Machine IKMP 1,2

Sahinler Manual and Motorized Bordering & Trimming Machine IBKS 2,5

Sahinler power operated bordering & Trimming Machine

Sahinler manual and motorized Bordering & Trimming Machine

Standard FeaturesIBKS Models

• Adjustable idle roll

• Reduction motor with brake system

• Movement of rolls with foot pedal

• Complete with 4 sets of standard rolls

Standard FeaturesIK-IKMP Models

• Adjustable side rolls

• Reduction motor with brake system

• Adjustable idle roll

• Complete with 8 sets of standard rolls & Stand

35

Harp Baykal Industrial Plasma Cutting Machine

With a foundation history going back to early 1950’s, Baykal today is placed as a leading manufacturer and global supplier of sheet metal working machinery. For its manufacturing operations Baykal utilizes three factories which together combine a production area of 60,000 square meters, making it one of Europe’s largest facility for sheet metal working and fabricating machinery. All the machines off ered by Baykal are designed, manufactured, assembled and fi nished wholly at Baykal’s purpose – built plants in a CAD environment with extensive use of CNC Machining and modern workshop equipment. These Plasma Cutting Machines are all-rounder designed for most medium fabrication shops and small service centre’s to large produc-tion plants. It can carry plasmas form 50 – 400 amps up to 4 tool carriages and a total of 8 tools.

Specifications: BPL-H3006 BPL-H3008 BPL-H3010 BPL-H3012 BPL-H3014 BPL-H3016 BPL-H3018Width 5200mm 5200mm 5200mm 5200mm 5200mm 5200mm 5200mmLength 8000mm 10000mm 12000mm 14000mm 16000mm 18000mm 20000mmHeight 1900mm 1900mm 1900mm 1900mm 1900mm 1900mm 1900mmTable Height 750mm 750mm 750mm 750mm 750mm 750mm 750mmCutting Width 3200mm 3200mm 3200mm 3200mm 3200mm 3200mm 3200mmCutting Length 6400mm 8000mm 11200mm 12800mm 14400mm 17600mm 19200mmWeight 4100Kg 5600Kg 6300Kg 7050Kg 7800Kg 9100Kg 9850Kg

Specifications: BPL-H4006 BPL-H4008 BPL-H4010 BPL-H4012 BPL-H4014 BPL-H4016 BPL-H4018Width 6200mm 6200mm 6200mm 6200mm 6200mm 6200mm 6200mmLength 8000mm 10000mm 12000mm 14000mm 16000mm 18000mm 20000mmHeight 1900mm 1900mm 1900mm 1900mm 1900mm 1900mm 1900mmTable Height 750mm 750mm 750mm 750mm 750mm 750mm 750mmCutting Width 4400mm 4400mm 4400mm 4400mm 4400mm 4400mm 4400mmCutting Length 6400mm 8000mm 11200mm 12800mm 14400mm 17600mm 19200mmWeight 5900Kg 8200Kg 9300Kg 10450Kg 11600Kg 13700Kg 14850Kg

36

HarpGenerator 15GF

Butler Elgamill Bed Type CS10

The world’s most versatile milling machine

Specifi cationsBUTLER Elgamill - Bed Type - Model CS10 - Table size 5000mm x 1030mm , Longitudinal travel 3300mm, Ram travel 960mm, Vertical Travel 1200mm, Spindle speeds 30-2030Rpm, Huron type head, Spindle Taper ISO50, Easson 3 Axis Digital Readout.

Other models available on request -

up to 10 000mm bed.

Harp Generators - Silent Type

Specifications: 5.5kVa 15GF 25GFFrequency 50Hz 50Hz 50HzRated output 5kW 15kw 25kwMax. output 5.5kw 16.5kw 27kwRated voltage 110/240V 230/400V 230/400VRated current - 21.7A 45.2ADC output 12V 12V 30A 12V 30APhase 1 3 3Pole number 2 4 4Engine type Air cooled Water cooled Water cooled

4 stroke / 1 cylinder 4 stroke / 3 cylinder 4 stroke / 4 cylinderPetrol / Diesel Petrol Diesel Diesel

Used Butler Elgamill Bed TypeMilling Machine

HARP HAVE SOLD 440 WEBSTER & BENNETTSHARP HAVE SOLD 440 WEBSTER & BENNETTS

37

HARP ! S.A.’S WEBSTER & BENNETT SPECIALIST

Used Webster & Bennett Vertical Boring Mills

THE WORLD’S BEST VERTICAL BORING MILLS

WEBSTER AND BENNETT 72" EM Type Vertical Boring Mill - Elevating rail -Chuck diameter 1830mm - Maximum swing 2134mm - Height under the bridge 1143mm - Speeds 5.2-117Rpm -

Toolholders - Boring Bar - New Easson 2 Axis DRO.

WEBSTER AND BENNETT 48" DH Type Vertical Boring Mill - Chuck diameter 1220mm - Maximum swing 1480mm - Height under the bridge 630mm - Speeds 5.6-125Rpm - 2 x Tool holders - 1 x Boring bar - New Easson 2 Axis DRO.

WEBSTER AND BENNETT 36" V Type Vertical Boring Mill - Thorn Electronic Copy Attachment - Chuck Diameter 915mm - Maximum swing 1100mm - Height under the bridge 700mm - Speeds 7.5-167Rpm - 2 x Tool holders - 1 x Boring bar - New Easson 2 Axis DRO.

38

Used Webster & Bennett Vertical Boring Mills

WEBSTER AND BENNETT 48" EH Type Vertical Boring Mill - Chuck diameter 1220mm - Maximum swing 1600mm - Height under the bridge 1220mm - Speeds 4.5-100Rpm - 2 x Tool holders - 1 x Boring bar - New Easson 2 Axis DRO.

WEBSTER AND BENNETT 65" DH Type Vertical Boring Mill - Chuck diameter 1650mm - Maximum swing 1830mm - Height under the bridge 635mm - Speeds 3.8-83Rpm - 2 x Toolholders - 1 x Boring Bar - New Easson 2 Axis DRO.

WEBSTER AND BENNETT 60”DH Type Vertical Boring Mill -Chuck diameter 1525mm - Maximumswing 1700mm - Height under the bridge 630mm - Speeds 1.8-83.2Rpm -Toolholders - Easson 2 Axis DRO

WEBSTER AND BENNETT 54" EM Type Vertical Boring Mill - Chuck diameter 1372mm - Maximum swing 1572mm - Height under the bridge 1200mm - Speeds 3.1-70Rpm - 2 x Toolholders - 1 x Boring Bar - New Easson 2 Axis DRO.

WEBSTER AND BENNETT 36" M Type Vertical Boring Mill - Chuck Diameter 915mm - Maximum swing 1225mm - Height under the bridge 600mm - Speeds 9-234Rpm - 2 x Tool holders - 1 x Boring bar - New Easson 2 Axis DRO.

WEBSTER AND BENNETT 36" DH Type Vertical Boring Mill - Chuck Diameter 915mm - Maximum swing 1080mm - Height under the bridge 500mm - Speeds 8.6-192Rpm - 2 x Tool holders - 1 x Boringbar - New Easson 2 Axis DRO.

39

Accessories

Digital Readout Systems

Harp Service & Spares

40

Harp Service & Spares

QUALITY

NEW

AND

USED

MACHINE

TOOLS

SHOWROOM ADDRESS

161 Dormehl RoadAnderboltBoksburg NorthGAUTENG, SOUTH AFRICA

TELEPHONE

(011) 918-5138

CELL

083 254-0746 (Shamus Thompson)

E-MAIL: harp@icon.co.za

POSTAL ADDRESS

P.O. BOX 2698BENONI1500GAUTENG, SOUTH AFRICA

FAX

(011) 918-5139

INTERNATIONAL CODE

(+27 11) 918-5139

WEBSITE: www.harp.co.za

GPS CO-ORDINATESS26° 11.665’ • E028° 16.202’