Embed Size (px)
Citation preview
136
Dimensions in millimeters (inch) unless otherwise stated
ACTUAL SIZE
Concealed latch points•Door ejection feature•Accommodates •
misalignmentSingle or two point latching •
Material and FinishSteel, zinc plated and thermoplastic, white, aluminum, natural
Performance Details
Operating temperature range: -18ºC (-0ºF) to 120ºC (250ºF)
Flammability rating: UL94-V0
Installation NotesSee page 138
*Nominal keeper location from inside surface of door. Adjustable 6.4 (.25) either way to allow for variations in mounting, gasketing, etc
Near Edge Complete Assembly Part Number
With Fixed Keeper With Floating Keeper
E2-50-101-10 E2-50-101-20
Part NumberSee table
www.southco.com/E2
14.3 (.56)
5.2 (.203)
25.5 (1.00)
12.7(.50)20.6
(.81)
41.3 (1.63)
3/8-24 thread
38 (1.50) nominal keeper location frominside surface of door. Adjustable 6.4 (.25)either way to allow for variations in mounting, gasketing, etc.
16(.63)
25.5(1.00)
8 (.312)
23.8(.94)47.6
(1.88)
52.4(2.06)
19(.75)
4.4 (.17) operating stroke
Ø 7.1 (.28)
19(.75)
28.6(1.13)
33.4(1.32)
20.9(.82)
8(.31)
62(2.44)
1.5(.06)
Actuatorbutton
Panel edge for exposed actuator (finger operated)
Panel edgefor concealed actuator(tool operated)
9.5(.38)hole
Ø
Ø 5.2 (.203)
Keeper
Latch
38 (1.50)*
1.6(.06)
20.6(.81)
15.6(.62)
7.1 (.28)
5.2(.203)
ReceiverAssembly
Latch
Actuator66.7
(2.63)
Adjusting Screw
Ø
Ø
24(.94)
12.7 (.50)
2(.08)U-bent
washer
Stud
Lockwasher
Eyelet
Length of rod160 - 1372 (6.3 - 54.0)
4.4 (.17) Operating stroke (will vary depending upon rod length)
Panel edge for exposed actuator (finger operated)
Panel edgefor concealed actuator(tool operated)
E2 Push-to-Close LatchPush-button to open · Hidden panel latching system
Floating Keeper for Hinged Panels Fixed Keeper for Lift-Off Panels
A complete near edge assembly comes with keeper
Available in Two Versions - Near Edge and Remote Near Edge Remote
1. Select Keeper
2. Determine Latch Location - Near Edge or Remote (Single or Two Point)Near Edge
Keeper styleStatic load
Ultimate load
Fixed1300 N
(300 lbf)2200 N
(500 lbf)
Floating750 N
(170 lbf)1400 N
(310 lbf)
137
Remote Single Point Part Number
Fixed keeper E2-55-101-10
Floating keeper E2-55-102-10
Rod 500 mm E2-46-0500-16
Rod 1250 mm E2-46-1250-16
Latch E2-92-101
Actuator E2-91-101
Remote Two Point Part Number
Fixed keeper E2-55-101-10
Floating keeper E2-55-102-10
Rod 500 mm E2-42-0500-16
Rod 1250 mm E5-42-1250-16
Latch E2-92-102
Actuator E2-93-102
Dimensions in millimeters (inch) unless otherwise stated
25.5(1.00)
8 (.312)
23.8(.94)
52.4(2.06)
19 (.75)
4.4 (.17) Operating stroke (will vary depending upon rod length)
Ø 7.1 (.28)
19(.75)
28.6(1.13)
33.4(1.32)
8 (.31)
62(2.44)
1.5(.06)
Ø 9.5 (.38) hole
38 (1.50)*
Length of rod160 - 1372 (6.3 - 54.0)
16 (.63)
Actuator extension rod
47.6(1.88)
16 (.63)Door
Ø 5.2 (.203) holes
Latch
Actuator
Keeper
Panel edge for exposed actuator (finger operated)
Panel edgefor concealed actuator(tool operated)
38 (1.50)*
1.6(.06)
20.6(.81)
15.6(.62)
7.1 (.28)
5.2(.203)
ReceiverAssembly
Latch
Actuator66.7
(2.63)
Adjusting Screw
Ø
Ø
24(.94)
12.7 (.50)
2(.08)U-bent
washer
Stud
Lockwasher
Eyelet
Length of rod160 - 1372 (6.3 - 54.0)
4.4 (.17) Operating stroke (will vary depending upon rod length)
Panel edge for exposed actuator (finger operated)
Panel edgefor concealed actuator(tool operated)
Remote - Single Point Remote - Two Point
To order rod lengths other than the standard lengths, use part number: E2-42-XXX-16 (XXX = length in mm) Min. = 160 mm Max. = 1372 mm Min. order = 50 units
A complete remote single point assembly consists of 4 components: keeper, rod, latch and actuator
A complete remote two point assembly consists of 4 components: keeper, rod, latch and actuator
138
Dimensions in millimeters (inch) unless otherwise stated
Installation Notes1. Mount brackets on inside surface of your panel using studs, welds, M5 (No.10) screws or Ø 5 (.188) rivets.
2. Slide receiver assembly into side of upper bracket.
3. Insert extension rod into brackets, then slide receiver assembly into side of lower bracket and snap-in actuator button.
4. Mount keeper with M5 (No. 10) screws. Keeper can be adjusted 3.2 (.13) from center both vertically and horizontally for proper alignment with latch.
www.southco.com/E2
BracketReceiverassembly
13 (.50)approx.
22 (.88)approx.
Finger (push-button) operation
Push-tool operation(button recessed)
Barb
Extentionrod
Actuator button
Remote Latching Style
Near Edge StyleSnap actuator button into bracket
Extensionrod
Barb
Actuatorbutton
Two-Point StyleInsert extension rod into brackets then slide receiver assembly into side of lower bracket and snap in actuator button
Remote Latching StyleInsert extension rod and actuator button into brackets
E2 Push-to-Close LatchPush-button to open · Hidden panel latching system
