Upload
sticker592
View
870
Download
16
Embed Size (px)
DESCRIPTION
THermo
Citation preview
P. 8.1) CO2 at 15MPa and 25°C is throttled to 0.1Mpa. Determine the temperature andfraction vapor. (NOTE: there is a typo. Part (c ) makes no sense at 1.5MPa.)Solution: Ebal for a valve, 0=∆H(a) assume ideal gas,
( ) KTTCpH 2980 2 =⇒∆==∆⇒(b) by PREOS.XLS with Ref=224.1K,0.1MPa, “Liquid”.H2 = H1 = 9695 J/mol, then “T2sat” = 184.1K. q=(9695-0)/(17066-0)= 57%Note: This is just an estimate, because CO2 is not really liquid at 0.1MPaNote2: If you solved this using 1.5MPa, you get 281K.( c ) Note: for the problem statement at 1.5MPa, there is no difference from (b).At 5.27bar, 216.6K, Hsolid=HsatVap-Hsub,Hsub=Hvap+Hfus=17829-2420+43.2*44*4.184=23362⇒ Hsolid=17829-23362= -5533.C-Ceq⇒ ln(Psat/Pref)= -(Hsub/R)*(1/T-1/Tref)⇒ 1/T=1/216.6-ln(1/5.27)/(23362/8.314)=0.005208 ⇒ T=192At 1bar, 192K=HsatVap=17322 ⇒ Hsolid=17322-23362= -6040⇒ q = (9695+6040)/(23362) = 67%FYI: This one way to make “dry ice.” You throttle/spray it into “bag” and compress itinto a block. See also CO2 chart in Perry’s Handbook, Chapter 3.
P8.2) CO is liquefied from 300bar,150K to 1bar. Compute q and Sgen.Soln: Ref=82.0K,0.1MPa,liq. H(150,30)=4139. Ebal:∆H=0; q=(4139-0)/(6048-0)=68%Sf=0.68*73.83+0 = 50.2; S(150,30)=27.365 ⇒ Sgen=50.2-27.4 = 22.8 J/mol-K.
P8.3) Same CO using 90% efficient turbine.∆Srev=0⇒ q=27.635/73.83=0.374; Wrev=0.374*6048-4139= -1877J/mol⇒Wact=-1689Hout=4139-1689=2450 ⇒ q = 2450/6048=40.5% ⇒ 1-q=59.5%
P8.4) Methane at 300K, 250bar is liquefied (~Linde style) with outlet pressure = 30bar.Compute fraction liquefied.Soln: Ref=111.8K,1bar; qH8+(1-q)H6=H3=10654; Tsat(30bar)=176.7KHsatVap=8289;HsatLiq=4104; H8=H(300,3MPa)=13455;q=(10654-4104)/(13455-4104)=70% ⇒ 1-q=30%
Chapter 10 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (07/06/01) 1 of 4
(P10.5) (a) Perform bubble P calculations 1-CO2, 2- ethylene. For kij = 0 Output from PRMIX.exe bp COMPONENT IS CARBON DIOXIDE ID NO. IS 909 COMPONENT IS ETHYLENE ID NO. IS 201 T(K)= 222.00 P(MPa)= .8725 ZL= .2138E-01 ZV= .8674 ID LIQUID X VAPOR Y Yi/Xi 909 .5000 .4057 .8114 201 .5000 .5943 1.189 repeating across the composition range: x1 y1 P(MPa) 0.0 0.0 1.02 0.1 0.0795 0.995 0.5 0.406 0.873 0.9 0.834 0.7012 1. 1. 0.642 End points were determined using bubble point pressure calculation using PRMIX for a single component. No azeotrope exists. Answer is 0.87MPa (b) Output from prmix.exe: Kij MATRIX MODIFIED 909 201 201 .1100 bp COMPONENT IS CARBON DIOXIDE ID NO. IS 909 COMPONENT IS ETHYLENE ID NO. IS 201 T(K)= 222.00 P(MPa)= 1.126 ZL= .2867E-01 ZV= .8358 ID LIQUID X VAPOR Y Yi/Xi 909 .5000 .4237 .8475 201 .5000 .5763 1.153 For kij = 0.11 x1 y1 P(MPa) 0.0 0.0 1.02 0.1 0.139 1.09 0.5 0.424 1.126 0.9 0.691 0.882 1. 1. 0.642 at small x1, x1<y1. At large x1, x1>y1. Also, P maximum in mixture. Therefore, maximum P (minimum T) azeotrope will exist. Answer is 11.3 bar.
Chapter 10 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (07/06/01) 2 of 4
(P10.6) (a) .Pentane 7 Acetone 1051 THE DEFAULT Kij MATRIX IS 7 1051 1051 .0000 bp COMPONENT IS n-PENTANE ID NO. IS 7 COMPONENT IS ACETONE ID NO. IS 1051 T(K)= 305.05 P(MPa)= .7785E-01 ZL= .3247E-02 ZV= .9697 ID LIQUID X VAPOR Y Yi/Xi 7 .7280 .8345 1.146 1051 .2720 .1655 .6083 Answer: 0.78 bar, y1 = 0.83 (b) x=0.134 using option KI, perform bubble pressure calcs until converge on experimental pressure of 1 bar at 0.728. ki Kij = 0.11 REQUIRED NUMBER OF ITERATIONS WAS: 7 COMPONENT IS n-PENTANE ID NO. IS 7 COMPONENT IS ACETONE ID NO. IS 1051 T(K)= 305.05 P(MPa)= .9927E-01 ZL= .4199E-02 ZV= .9634 ID LIQUID X VAPOR Y Yi/Xi 7 .7280 .7167 .9845 1051 .2720 .2833 1.041 Kij = 0.117 REQUIRED NUMBER OF ITERATIONS WAS: 5 COMPONENT IS n-PENTANE ID NO. IS 7 COMPONENT IS ACETONE ID NO. IS 1051 T(K)= 305.05 P(MPa)= .1011 ZL= .4282E-02 ZV= .9629 ID LIQUID X VAPOR Y Yi/Xi 7 .7280 .7078 .9723 1051 .2720 .2922 1.074 Intermediate Answer: kij = 0.117 to fit bubble pressure, azeotrope composition not matched exactly. bp COMPONENT IS n-PENTANE ID NO. IS 7 COMPONENT IS ACETONE ID NO. IS 1051 T(K)= 312.75 P(MPa)= .1120 ZL= .3881E-02 ZV= .9626 ID LIQUID X VAPOR Y Yi/Xi 7 .1340 .5453 4.070 1051 .8660 .4547 .5250 Answer: kij = 0.117, BP = 1.12 bar
Chapter 10 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (07/06/01) 3 of 4
(P10.7)
a) using shortcut K-ratio equation at 298K, predict the vapor pressure of components.
# COMPOUND Psat ( MPa) 1 CO2 6.44 2 METHANE 32.6 3 PROPANE 0.956 4 ETHANE 4.21 Note: methane is supercritical so the vapor pressure is extrapolated. yiP = xiPi
sat, xi = yiP/Pisat ! guess P until Σxi = 1.
PNEW = POLD / Σ Xi P(MPa) X1 X2 X3 X4 Σ Xi 3 0.14 0.028 0.628 0.143 0.939 3.19 0.149 0.029 0.667 0.152 0.997
3.2 0.15 0.0295 0667 0.153 0.9995 (b) there isn’t a DP routing, use dt routine, guess P until DT = 298 REQUIRED NUMBER OF ITERATIONS WAS: 6 COMPONENT IS CARBON DIOXIDE ID NO. IS 909 COMPONENT IS METHANE ID NO. IS 1 COMPONENT IS PROPANE ID NO. IS 3 COMPONENT IS ETHANE ID NO. IS 2 T(K)= 286.67 P(MPa)= 3.000 ZL= .9407E-01 ZV= .7509 ID LIQUID X VAPOR Y Yi/Xi 909 .2207 .3000 1.360 1 .0715 .3000 4.198 3 .5197 .2000 .3848 2 .1882 .2000 1.063 REQUIRED NUMBER OF ITERATIONS WAS: 6 T(K)= 295.61 P(MPa)= 4.000 ZL= .1286 ZV= .6876 ID LIQUID X VAPOR Y Yi/Xi 909 .2410 .3000 1.245 1 .0958 .3000 3.132 3 .4637 .2000 .4313 2 .1995 .2000 1.003 REQUIRED NUMBER OF ITERATIONS WAS: 5 T(K)= 298.45 P(MPa)= 4.400 ZL= .1434 ZV= .6624 ID LIQUID X VAPOR Y Yi/Xi 909 .2486 .3000 1.207 1 .1064 .3000 2.819 3 .4421 .2000 .4524 2 .2029 .2000 .9856
Chapter 10 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (07/06/01) 4 of 4
P = 4.4MPA, DT = 298.5 close enough. P(MPa) x1 x2 x3 x4 4.4 0.249 0.107 0.442 0.203 PR predicts much different P and composition. PR should be improved by using non-zero kij from binary data fits for even more accuracy.
(P10.8) ρρ
b
cbZ
−+=
1
41 ,
=
ρρ
ρρ d
b
db
∫ −−=−
=− ρρρ
ρb
TVig
bcbdb
c
RT
AA0
)1ln(4)()1(
4)(
……………………..…...Eqn. 7.27
( ) Zn
RTAA
RTijnVTi
TVigig
iii ln
/)()(ˆln
,,
−
∂
−∂=
−=
≠
µµϕ ……………….Eqn. 10.16
( ) Zn
bnc
ijnVTii ln
))1ln(*4(ˆln
,,
−
−−=≠
∂ρ∂ϕ
Zn
b
bnc
n
ncb
ijij nVTinVTi
ln)(
1
14
)()1ln(4
,,,,
−
−
+
−−=
≠≠∂
ρ∂ρ∂
∂ρ
ccxn
nc
iiji
nVTiii
−=
∑≠
2,,
∂∂
……………………………………………....Eqn. 10.29
i
nVTi
bn
nb
ii
=
≠,,∂∂
…………………………………………………………... Eqn. 10.22
second term in iϕ̂ln becomes equal to )1(1
4
14 −=
−
=−
Zb
b
b
cb
b
b
b
bcn iii
ρρ
ρ
⇒⇒⇒ ⇒ ZZb
bbcxc j
iijij ln)1()1ln(24ˆln −−+−
−= ∑ ρϕ
Chapter 14 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (02/11/02) 16
(P14.1) An equimolar mixture of H2 and CO can be obtained by the reaction of steam with coal. Compute the equilibrium compositions at 550 C based on an equimolar feed of H2, CO, and H2O. The reaction is H
�O + CO = H
� + CO
�. ∆Gf° data at 550 C are given.
�
∆�����Σ∆�
���������� �Σ∆�
���������������������������
�������������������������� �!����"�#�� ���������$%�
�
Compound In Out H2O 0.333 0.333−ξ CO 0.333 0.333−ξ H2 0.333 0.333+ξ CO2 0 ξ Total 1 1
Ka = 2
2
( )(0.333 )*(0.333 )*(0.333 )*
PP
ξ ξξ ξ
+− −
= 3.369
ξξξξ = 0.176; Ans. y1 = 0.157, y2 = 0.157, y3 = 0.509, y4 = 0.176 �
�& ������������'���(����'�������)����(�'*���+���*��)���),�-*��'��+�,��'�,���)���+����)����(�
���*���������)�+�����'������)���-���.���/�����,��)')�����)�(����������°�0���������'������������,)�)������ ���������-���+)1���∆�
�°�����������������
� � 2��"��
�3
�����3�2�
4���)��5�6.�������-�,),���7,,���)�����+�,��8��(�����,��2
�����8��(�����,���
�3
����� ���
�
Compound In Out N2 1 1−ξ C2H2 1 1−ξ HCN 0 2ξ Total 2 2 �������������������� �!����"�#�� ���������� ��
�����2 2
2 2
(2* ) *(1 ) *
PP
ξξ−
������� ��0�������������
�7�,����� �������%$0��
��������%$0��
�������� $��
������ � ���
Chapter 14 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (02/11/02) 17
(P.14.3) Butadiene can be prepared by the gas-phase catalytic dehydrogenation of 1-Butene: C4H8 = C4H6 + H2. In order to suppress side reactions, the butene is diluted with steam before it passes into the reactor. (a) Estimate the temperature at which the reactor must be operated in order to convert 30% of
the 1-butene to 1,3-butadiene at a reactor pressure of 2 bar from a feed consisting of 12 mol of steam per mole of 1-butene.
(b) If the initial mixture consists of 50 mol% steam and 50mol% 1-butene, how will the required temperature be affected?
∆Gf° 600K 700K 800K 900K C4H6 195.73 211.71 227.94 244.35 C4H8 150.92 178.78 206.89 235.35 Solution: Compound In Out C4H8 1 1-ξ C4H6 0 ξ H2 0 ξ H2O 12 12 Total 13 13+ξ P = 2 bar
( ) ( )
22
2*13 *
13 * 1113
0.01933
PPKa
P
Ka
ξξ ξ
ξ ξξξ
+ = =
+ − − +
=
Noting that lnKa = -∆Gtot/RT, we can identify the temperature by fitting a trendline to the given data. ⇒ ln 0.01933 = -3.95, substitute in the equation of straight line, ⇒ x = -(-14.34 � 3.95 )/13996. ⇒ x = 0.001306 = 1/T, ⇒ T = 765.22 K = 492OC
y = -13996x + 14.34
-10
-9
-8
-7
-6
-5
-4
-3
-2
-1
0
0.001 0.0012 0.0014 0.0016 0.0018
1 / T
ln K
a
Compound In Out C4H8 1 1-ξ C4H6 0 ξ H2 0 ξ H2O 1 1 Total 2 2+ξ
( ) ( )CKTSimilarly
PKa
O6.57365.846,
1118.01*2
*2
==
=−+
=ξξ
ξ
⇒ We need higher T.
Chapter 14 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (02/11/02) 18
(P14.4) The standard Gibbs energy change for ethylene oxide at 298K for the reaction is �79.79 kJ/mole. This large negative value of ∆GT° indicates that equilibrium is far to the right at 298K but what about 550K? Heat capacity expressions are given as CP= a + b T. Solution: The heat of reaction must be looked up. Referring to Apx E.6 for ethylene and the DIPPR handbook for ethylene oxide, ∆H298° = -52.6-52.51 = -105.1 kJ/mol. Following Eqs. 14.28 and 14.30, -105100 = J + (6.57-15.4-26.65/2) 298 + (0.1389-0.0937-0.00845/2) 2982/2 -105100 = J � 22.155 *298 + 0.040975*2982/2 ⇒ J =-100317 J/mol -79790/(8.314*298) = -100317/(8.314*298) �
79790 100317 22.155 0.040975ln 298 298 6.168.314*298 8.314*298 8.314 2*8.314
I I− − −= − − + => = −
100317 22.155 0.040975ln 550 550 6.16 12.68.314*550 8.314*550 8.314 2*8.314
G∆ − −= − − + =o
⇒ ∆G° = -57.7 kJ/mol. If T = 550 K, increasing T will give an adverse effect on equilibrium, but the reaction is still very strongly favored and the impact will be indistinguishable. (P14.5) The �water gas� shift is to be carried out at a specified temperature and pressure employing a feed containing only CO and H2O. Show that the maximum equilibrium mole fraction of H2 in the product results when the feed contains CO and H2O in their stoichiometric proportions. Assume ideal gas behavior. Solution: 222 HCOOHCO +=+ Compound In Out CO z z-ξ H2O 1 1−ξ CO2 0 ξ H2 0 ξ Total 1+z 1+z
( )( )( )( )
2
2
2 2
1
1 0
0 [ (1 ) ]
Kaz
Ka z
Ka z z
ξξ ξ
ξ ξ ξ
ξ ξ ξ
=− −
⇒ − − − =
= − − + +
ξ2(1-Ka) +Ka (1+z) ξ - Ka z = 0 ⇒ ξ = {-Ka(1+z) + [Ka2(1+z)2+4z(1-Ka)Ka]1/2 }/[2(1-Ka)] yH2 = ξ/(1+z) = {-Ka(1+z) + [Ka2(1+z)2+4z(1-Ka)Ka]1/2 }/[2(1+z)(1-Ka)] yH2 = ξ/(1+z) = {-Ka+ [Ka2+4z(1-Ka)Ka/(1+z)2]1/2 }/[2(1-Ka)] To find maximum, take derivative and set equal to zero. dy/dz = 0.5[Ka2+4z(1-Ka)Ka/(1+z)2]-1/2 [4(1-Ka)Ka/(1+z)2 � 8z(1-Ka)Ka/(1+z)3] = 0 1 = 2z/(1+z) ⇒ z = 1. QED. (P14.6) Assuming ideal gas behavior, estimate the equilibrium composition at 400K and 1 bar of a reactive mixture containing the three isomers of pentane. Formation data are given at 400K. Solution: This is best solved by the Gibbs minimization method, adapting Example 14.10 and GibbsMin from the Rxns.xls workbook, we obtain the following.
Gf(J/mole) Gf400/RT feed ni log(ni) yi ni(Gi/RT+lnyi)nPentane 40170 12.08 0 0.111 -0.95 0.111 1.100iPentane 34310 10.32 1 0.648 -0.19 0.648 6.408neoPentane 37610 11.31 0 0.240 -0.62 0.240 2.376Tot 1 1.000 9.884
Out InC-bal 5 5Hbal 12 12
Chapter 14 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (02/11/02) 19
(P14.7) One method for the manufacture of synthesis gas depends on the vapor-phase catalytic reaction of methane with steam according to the equation below. The water-gas shift reaction also is important. Bases on stoichiometric feed of methane and steam, compute the eq composition at 600K, 1300K and 1, 100 bars.
4 2 23CH H O CO H+ = + rxn(1)
222 COHCOOH +=+ rxn(2) Compound In Out CH4 1 1−ξ1 H2O 1 1−ξ1−ξ2 CO 0 ξ1−ξ2 H2 0 3ξ1+ξ2 CO2 0 ξ2 Total 2 2+2ξ1 600 164.68 214.01 22.97 72.3 / ......................... (1)KG kJ mole rxn∆ = − + + = 600 395.14 214.01 164.68 16.45 / ...................... (2)KG kJ mole rxn∆ = − + + = −
05.27
600*314.816450exp
708.5600*314.8/72300exp
2,600
1,600
=
=
−=
−=
K
K
Ka
EmoleJKa
( )( )
( )( )
3 41 2 1 2
41
1 21 1 2
21
3 21 2 1 2
21 1 2 1
( )(3 ) *(2 2 )
1 1 *(2 2 )
( )(3 ) *1 1 (2 2 )
P
KaP
P
ξ ξ ξ ξξ
ξ ξ ξξ
ξ ξ ξ ξξ ξ ξ ξ
− ++=
− − −+
− +=− − − +
( )( ) ( )( )
22 1 2
2 1 22 2
1 1 2 1 1 2
( )*( )4
1 * 14
PKa
P
ξ ξ ξξ ξ ξ
ξ ξ ξ ξ ξ ξ
++= =
− − − −
Note: high pressure tends to disfavor rxn (1). Rxn 1 is negligible at 600K, and rxn (2) requires CO to run or ξ1-ξ2 will be less than zero. So both reactions are zero. At 1300 K, the situation is quite different.
1300 226.94 175.81 53.30 104.73KG∆ = − + − = − ⇒ Ka1 = 16113
1300 396.14 226.94 175.81 6.614KG∆ = − + + = ⇒ Ka2 = 0.54 Solving by method of Example 14.9, ξ1 = 0.972 and ξ2 = 0.015 at 1 bar. At 100 bar, ξ1 = 0.451 and ξ2 = 0.149 at 100 bar
PP 14.7Two simultaneous reactions:CH4 + H2O =CO + 3H2H2+CO2 = CO + H2O(Details of equations described in text)P(bars) 100T(K) 1300Ka1 16113Ka2 0.5400ξξξξ1 0.4513ξξξξ2 0.1491y1 0.1891y2 0.1377y3 0.1041y4 0.5178y5 0.0514
nTot 2.9025Objective Functionserr1 0.0000err2 0.0000
Chapter 14 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (02/11/02) 20
(P14.8) Is there any danger that solid carbon will form at 550°C and 1 bar by the reaction: 22 COCCO S +=
molekJH K /298∆ molekJG K /298∆ IN Out CO -110.53 -137.16 2 2-2ξ Cs 0 0 0 0 (gas) CO2 -393.51 -394.38 0 ξ Tot 2-ξ
molekJHmolekJG
TK
TK
/45.17253.110*251.393/06.12016.137*238.394
,298
,298
−=+−=∆−=+−=∆
Increasing T, adverse affect on equilibrium
2108.115.298*314.8
120060expexp 298298 E
RTG
Ka KK =
=
∆−
=
Using Shortcut Van�t Hoff Eq. 14.31
( )
298
298 298
1 1 172450 1 1ln ln1.08 21 8.314 823.15 298.15
ln ln 1.08 21 44.4 4.06 exp(4.06) 57.99
HKa KaKa R T T E
Ka E Ka
−∆ ⇒ = − = = − ⇒ = − = ⇒ = =
( )( )
( )( )
( )( )
2
2 2 2
2* * 257.99
* 2 22 22
CO
CO
y PKa
y P
ξξ ξ ξ
ξξξ
− − ⇒ = = = =
−− −
ξ = 0.9345 ⇒ ratio of carbon solid to feed is 2
9345.0 = 0.46725. ⇒ There is danger.
Note: this exemplifies a very important and undesirable side reaction in many catalytic reactions know as �coking.� The carbon tends to clog the catalyst pores and substantially reduce its effectiveness. Because of this problem, fluidized catalytic crackers were developed (aka. Cat crackers). The solid catalyst particles are fluidized by the upflow of gaseous reactants. As they ultimately settle at the bottom, they are removed and recirculated through an oxidation zone that burns off the coke then recycles the catalyst to the top of the bed. This is a good example of how thermodynamics impacts reactor design. (P14.9) Calculate the equilibrium percent conversion of ethylene oxide to ethylene glycol at 298K and 1 bar if the initial molar ratio of ethylene oxide to water is 3. In Out(zi) EtO 3 3-ξ Water 1 (1-ξ) Glycol 0 ξ Tot 4-ξ Kw = Psat/P = 0.0425; KEtO = 1.76; KGly = 8.6E-4; yi = zi Ki /[ Ki +L/F*(1- Ki)]
2
7824exp 23.52* * 298.15*8.314
Gly
EtO W
y PKa
y y P = = =
and Σ yi = 1 are constraints, ξ and L/F are
unknown. Guess, ξ = 0.99, L/F = 1/3 (all glycol in liquid, all EtO in vapor).
Chapter 14 Practice Problem Solutions
To accompany Introductory Chemical Engineering Thermodynamics J.R. Elliott, C.T. Lira, 2001, all rights reserved. (02/11/02) 21
(P14.9) Sample solution of one reaction with vle:(Details of input equations described in text by Elliott and Lira)P(bar) T(K) Ka1
1.000 298 23.52
pSat(bar) K-ratios zFeed yi xiEtO 1.76000 1.76000 0.66676 0.99961 0.56796Water 0.04250 0.04250 0.00029 1.579E-05 0.00037Glycol 0.00086 0.00086 0.33295 0.00037 0.43167
1.0000 1.0000 1.00001-ξ 8.7055E-04ξ 0.99913 sum(yi-xi) 0.00000L/F 0.77111 ErrKa 5.583E-07 As it turns out, the ethylene oxide is not so volatile after all and dissolves a fair amount in the liquid. The guess about the extent of conversion being high was good though. A more clever engineering approach would be to assume complete conversion and solve the simple flash. Then back out the exact conversion assuming L/F does not change. (P14.10) Acetic acid vapor dimerizes according to 2A1 = A2. Assume that no higher-order associations occur. Supposing that a value for Ka is available, and that the monomers and dimers behave as an ideal gas, derive an expression for yA1 in terms of P and Ka. Then develop an expression for PV/n0RT in terms of yA1, where n0 is the superficial number of moles neglecting dimerization. Hint: write n0/nT in terms of yA1 where nT = n1+n2. Solution:
0 1 21 1 1
2 2(1 ) 2A A AT T
n n n y y yn n
+= = + − = −
221 1 12
1
1 1 412
AA A A
A
y PKaKa y y PKa yy P PKa
− + += ⇒ − = ⇒ =
0 0 1
1Ideal gas 12
T
T A
PV PV nn RT n RT n y
⇒ = ⇒ = =−
Note: as Ka → ∞, PV/n0RT → ½ because the monomer is converted to dimer. Note also that PV/n0RT is what we normally refer to as the compressibility factor, Z. This is an interesting result with regard to equations of state and phase equilibria. Since Ka is simply a function of temperature [ie. exp(-∆G/RT)], it says that we can compute Z given a pressure and temperature. This is analogous to the pressure explicit virial equation (Section 6.4), but the form of the pressure dependence is more complex. Exploring this perspective, generalizing to density-dependent equations, and adapting to multimer-forming species and mixtures is the subject of Chapter 15. Most of the physical insight contained in Chapter 15 is contained in this simple practice problem.
Chapter 3 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 1 of 6
(P3.1)
(a) the number of microstates is N2 (pg 91, typo in given answer, printings 1-3) (b) 3 particles total
3!1!*2
!3}1,2{ ==⇒ THp number microstates of specific arrangement (macrostate)
probability = (# microstates of specific arrangement)/(total # of microstates)
8
3
2
33
==prob
(c ) # microstates.
20!3!*3
!6
15!2!*4
!6
10!2!*3
!5
6!2!*2
!4
}3,3{
}2,4{
}2,3{
}2,2{
==
==
==
==
TH
TH
TH
TH
p
p
p
p
(d) macrostate
H T # of microstates*
0 8 1 1 7 8 2 6 28 3 5 56 4 4 70 5 3 56 6 2 28 7 1 8 8 0 1
* number of microstates = )!8(!
!8
mm −
total number of microstates is 28 = 256, which is the same as the sum from the table. portion of microstates (probability) for requested configurations: {5:3} = 56/256 = 0.219 = 22% {4:4} = 70/256 = 0.273 = 27% {3:5) = 22% like {5:3} probability of any one of the three most evenly distributed states = 22% + 27% + 22% = 71% (e) for 8 particle system, Stirling’s approx will not apply ∆S/k = ln(p{4:4}/p{5:3}) = ln (70/56) = 0.223
Chapter 3 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 2 of 6
(P3.3) 15 molecules in 3 boxes, molecules are identical
!
!
1ij
i
j
m
Np
∏=
= ………………………………………....Eqn. 3.4
75075!2!4!9
!151 ==p
756756)!5(
!1532 ==p
31.2ln1
2 =
=
∆−
p
p
k
S
(P3.4) two dices.
??=∆k
Sfor going from double sixes to a four and three.
⇒ for double sixes, we have probability of 1/6 for each dice.
⇒ ( ) ( )!61!*6
1!2
1 =p
for one four and one three ⇒ probability applied for 1/6 for each one in each dice,
( ) ( ) 2*!6
1!*61
!22 =⇒ p
693.02lnln1
2 ==
=∆
p
p
k
S
(P3.5) ∆S = ?? Assume Nitrogen is an Ideal gas ⇒ RTPV = ……………. Eqn. 1.15
⇒ ( )( ) MPa
LcmmoleL
KKmoleMPacmP 108.0
)1/1000(*/23
300*/*314.83
3
1 =−=
Similarly ⇒ MPaP 00723.02 =
1
2
1
2 lnlnP
PR
T
TCpS −=∆ ……………………………………… Eqn. 3.23
2
7RCp = …..(ig)
KkgkJKmoleJ
RS −=−=−=∆ /07.1/88.30
108.0
00723.0ln*314.8
300
400ln*
2
7
(P3.6) (a) m-balance: dnin = -dnout
S-balance:
Chapter 3 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 3 of 6
dt
dnS
dt
nSd outout
in
−=)( ⇒ outoutinininin dnSdnSdSn −=+
But physically, we know that the leaking fluid is at the same state as the fluid in the tank; therefore, the S-balance becomes:
0 so and ,)()( =∆−=−=+ SdndnSdnSdnndS outinsideoutinside from the steam table .
By interpolation, implies T = 120.8OC (P3.7) (a) Steady-state flow, ∆H = Ws
Start 1 mole basis:
221121 ,,667.0,333.0 CpxCpxCpadiabaticxx +=== , Cp for each is the same anyway. )/(66.102*667.0)1612(333.02211 molegMWxMWxMW =++=+= R = 1.987BTU/lbmol-R.
( )
hBTUWH
lbmol
BTU
lb
lbmol
h
lbH
lbmollbMW
hlbhtonm
lbmolBTUH
RRCpdTWH
S
T
T
S
/10*3.1000,305,1
5.6954*
66.10*
2000
/66.10&
./2000/1&
/5.6954
1001100**2
7
6
2
1
===∆⇒
=∆⇒
===
=∆⇒
°−===∆ ∫
&
(b) ??=η of the compressor.
To find the efficiency of the compressor, ⇒ S1 = S2
But the enthalpy and the internal energy will change which gives a change in the
Work. ⇒ ??'
==S
S
W
Wη
At 1 bar = 0.1 MPa T S
100 7.361
120.8 7.4669 150 7.6148
State P(Mpa) TOC H(kJ/kg) S(kJ/kg*K) 1(in) 1 400 3264.5 7.4669
2 (out) 0.1 120.8 2717.86 7.4669
Chapter 3 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 4 of 6
RT
RT
TP
PT
P
P
T
T
P
PR
T
TCp
P
PR
T
TCpS
Cp
R
RCp
1315
559*5
100
*
lnln
lnln0
2
7
2
2
11
22
1
2
1
2
1
2
1
2
1
2
1
2
=′
=′⇒
=′⇒
=
′⇒
=′
⇒
−′
==∆
lbmolBTUH
TTCpH
/5258
)5591315(95.6)(& 12
=′∆⇒−=−′=′∆
76.06955
5258 ==∆
′∆=⇒H
Hη
(P3.8) Adiabatic, steady-state open system ⇒ Q = 0, &(Cp/R = 7/2)………………………… ig
kgkJkg
kmolekmolekJ
RCpdTW /76.337
28
1*/175.9457)300625(*
2
7625
300
==−== ∫
??=η
( ) ( )
molkJH
TTCpH
KT
P
P
T
TS
Cp
R
/77.6794
3005.533*2
314.8*7
5.533
0
12
2
1
2
1
2
=′∆⇒
−
=−′=′∆⇒
=′⇒
=
′⇒=∆
%8.71
718.0/28*/76.337
/77.6794
=⇒
==∆
′∆=⇒
η
ηkmolkgkgkJ
kmolkJ
H
H
(P3.9) work required per kg of steam through this compressor? By looking at the steam table in the back of the book
P(MPa) T(OC) H(kJ/kg) S(kJ/kg-K) 0.8 200 2839.7 6.8176
4 500 3446 7.0922 kgkJHW /3.6067.28393446 =−=∆= now find W’ = ??
Chapter 3 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 5 of 6
∆S = 0 (reversible), ⇒ look in the steam table (@P = 4.0MPa) to find a similar value for S = 6.8176kJ/kg-K, if this value is not available so find it by interpolation.
7.3246',7714.69386.6
8176.69386.6
5.32142.3331
'5.3331 =⇒−−=
−−⇒ H
H
kgkJWH /4077.28397.3246'' =−==∆⇒
%67,67.03.606
407 =⇒==⇒ ηη
(P3.10)@ P = 2.0 MPa & T = 600OC, ⇒ H = 3690.7 kJ/kg, S = 7.7043kJ/kg-K (Steam table) kgJkHqHH Vap
L /49.2493)68.2441(*98.046.1006)( =+=∆+=
⇒ kgkJHWS /21.119749.24937.3690 =−=∆=
??=η , '' W
W
H
H =∆∆=η ,
⇒ ∆S = 0 ( reversible), ⇒ look for S in the sat’d temp. steam table and find H by interpolation, ⇒ kgkJW /0.1408'=
⇒ %85,8503.00.1408
2.1197 =⇒== ηη
(P3.11)
CT
MPaP
dSatMPaP
O
vap
1100
10
',1.0
2
2
1
=
=
=
State P(MPa) T(OC) H(kJ/kg) S(kJ/kg-K)
1 0.1 99.61 2674.95 7.3589
2' 10 4062.53 7.3589
2 10 1100 4870.3 8.0288 interpolation for above table:
H(kJ/kg) S(kJ/kg-K) 3214.5 6.7714
H' = ?? S' = 6.8176 3331.2 6.9386
TOC HL(kJ/kg) ∆Hvap(kJ/kg) steam table 20 83.91 2453.52 Interpolation 24 100.646 2444.098 steam table 24 104.83 2441.68
Chapter 3 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 6 of 6
kgkJWH S /35.219595.26743.4870 =−==∆⇒
mass flow rate = 1 kg/s
hpW
hpwatt
wattskJW
S
S
01.2944
001341022.01&
2195350/35.2195
=⇒
===⇒
&
&
%2.63
63.035.2195
58.1387
/58.138795.267453.4062&
=⇒
==∆
′∆=⇒
=−=′∆
η
ηH
H
kgkJH
(P3.13) Through the valve ⇒ outin HH =
MPaPin 3= MPaPout 1.0= KCT Oout 15.383110 ==
(By interpolation) Find outH from steam table.
8.26756.2776
6.2776
100150
110150
−−=
−− outH
⇒⇒⇒ ⇒ outH = 2695.96 kJ/kg
At 3MPa table use same value for Hin to find Sin
⇒⇒⇒ ⇒ By interpolation 1856.62893.6
2893.6
2.28035.2856
96.26955.2856
−−=
−− inS
⇒⇒⇒ ⇒ Sin = 5.976kJ/kg-K
The process should be irreversible. To find Sout, interpolate using temperature at 0.1 MPa:
3610.76148.7
6148.7
100150
110150
−−=
−− outS
Sout = 7.4118 kJ/kg-K, since Sout>Sin entropy has been generated. The entropy balance is:
genoutoutinin SmSmS &&& +−=0
H'2 = 4062.53 (interpolation)
H(kJ/kg) S(kJ/kg-K) 3992 7.2916
4062.53 7.3589
4114.5 7.4085
Chapter 6 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 1 of 2
(P6.2) 15,30 == rr TP (a) Use virial equation of state.
rr TPBBZ /)(1 10 ω++= …………………………………………..Eqn. 6.6
Where,
2.41
6.10
172.0139.0
422.0083.0
r
r
TB
TB
−=
−= ………………………………. Eqns. 6.8 & 6.9
)(041.0&
138998.0&
077459277.01
0
book
B
B
−==
=⇒
ω
14.115
30*)138998.0*041.0077459277.0(1 =−+=⇒ Z
(b) ??=ρ
MPaPPP
KTTT
Cr
Cr
59.7930*653.2*
6664.44*15*
======
3
3
/254.093.3
11
/93.3179.20*59.79
666*314.8*14.1
*
**,
cmgV
gcmMWP
TRZV
RT
PVZ
===⇒
===⇒=
ρ
(P6.4)
KCFT
MPaatmP
KT
OO 15.2982577
1.01
111
2
1
1
===
≈==
Use PREOS.XLS, ⇒ Use Solver, and set target cell on the volume and make it equal to
33.639114*2 = 67.278228, Then by changing the cell of pressure, making sure that T2 = 298.15K
Current State Roots
T (K) 298.15 Z V
P (MPa) 33.839895 cm3/gmol
Current State Roots
Stable Root has a lower fugacity
T (K) 111 Z V fugacity
P (MPa) 0.1 cm3/gmol MPa answers for three 0.9670679 8924.6249 0.096803
root region 0.0263855 243.49944 0.0036451 33.639114 0.093707
Chapter 6 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics © J.R. Elliott, C.T. Lira, 2001, all rights reserved. (7/6/2001) 2 of 2
answers for three #NUM! #NUM! root region #NUM! #NUM!
#NUM! #NUM!
& for 1 root region 0.9184568 67.278228
MPaP 84.332 =⇒
Chapter 7 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics© J.R. Elliott, C.T. Lira, 2001, all rights reserved. (3/10/2007) 1 of 5
(P7.1) TSHG −≡
RSS
RTHH
RTGG igigig −
−−
=−
⇒ …………………………………Eqn. 7.21
( ) 112
310
2/50
−+
+
−−=−+
∂∂
−=−
∫∫ ZdbRT
aTZdTZT
RTHH ig
ρρ
ρρ
ρρ ρ
ρ
ρ
note: )(log1 baxabax
dxe +=
+∫
( ) ( ) 11ln12
311ln12
32/3
02/3 −+
+=−+
+= Zb
bRTaZ
Rab
bTρρ
ρ
( ) ( ) ZdZTZT
RSS ig
ln10
+
−−∂
∂−=−
∫ ρρρ
ρ………………………..Eqn. 7.23
( ) ( )
( ) ( ) ( ) ZbRT
abbbRT
a
ZdbRT
ab
bdbRT
a
ln1ln1ln1ln123
ln1112
3
2/32/3
02/3
02/3
+++−+
+=
+
+
−−
−
+
= ∫∫
ρρρ
ρρ
ρρρ
ρ
ρρ
( ) ( ) ( ) ( )
( ) ( ) ZZbbRT
abRT
GG
ZbRT
abbbRT
aZbbRT
aRSS
RTHH
RTGG
ig
igigig
ln11ln1ln
ln1ln1ln1ln12311ln1
23
2/3
2/32/32/3
−−++−−−=−
⇒
+++−+
+−−+
+⇒
−−
−=
−⇒
ρρ
ρρρρ
Or by using Eqn. (7.26)
( ) ( ) ZZdZRT
GG ig
ln11
0
−−+−
=−
⇒ ∫ ρρ
ρ
( ) ( ) ZbbRT
abRT
GG ig
1ln1ln 2/3 −++−−−=−
⇒ ρρ( ) ( ) ZZd
bRTa
bb
RTGG ig
ln1110
2/3 −−+
+
−−
=−
⇒ ∫ ρρ
ρρ
ρ
Chapter 7 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics© J.R. Elliott, C.T. Lira, 2001, all rights reserved. (3/10/2007) 2 of 5
(P7.2) rTbZ /1 ρ−=
Depature function ⇒ 10
−+
∂∂
−=
−∫ Zd
TZT
RTHH ig
ρρ
ρ
ρ
…………Eqn. 7.24
rrr
r
rrr
ig
Tb
Tb
TbT
Tbd
TbT
RTHH ρρρρ
ρρρρ 2
220
−=−−
=−
−=
−⇒ ∫
(P7.3) (a) UCvdtT
T
∆=∫2
1
, ⇒ CvTU
V
=
∂∂
ρρ
ρ
ρ dTZT
RUU ig
∂∂
−=−
∫0
2
ρρ
ρρ
dT
ZTdTdZT
TU
V
)2( 2
22
∂∂
−
−=
∂∂
⇒
ρρ
ρρ
ρ dT
ZTdTdZT
RCvCv ig
)2( 2
22
0
∂∂
−
−=
−⇒ ∫
(b) ( ) ρρρ
ρ+−
++= )exp(
11 T
ab
bZ
( )
( ) ( ))exp()exp(2
)exp(
4
2
32
2
2
Ta
Ta
Ta
Ta
TZ
Ta
Ta
dTdZ
ρρ
ρ
ρ
ρ
−−=
∂∂
⇒
=
⇒
( ) ( ) ( )ρρρρρ
ρ dT
aTaT
Ta
TaTT
aTaT
RCvCv ig
})exp()exp(2)exp(2{ 4
22
32
02 ++−=
−⇒ ∫
First two terms cancel, integral with respect to ρ is simple.
( ))exp(2
2
Ta
Ta
RCvCv ig ρ
=−
⇒
Chapter 7 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics© J.R. Elliott, C.T. Lira, 2001, all rights reserved. (3/10/2007) 3 of 5
(P7.4) Helmholtz Energy, ⇒ A = ??
Depature function, ⇒ RSS
RTUU
RTAA igigig −
−−
=−
…………….Eqn.7.20
ρρ
ρ
ρ dTZT
RTUU ig
∫
∂∂
−=−
0
………………………………………….Eqn. 7.22
ρε
ρερ
RTbN
dRT
bNT AA 5.95.9
02
−=
−= ∫
( ) ZdZdTZT
RSS ig
ln100
+−−
∂∂
−=−
∫∫ ρρ
ρρ ρ
ρ
ρ
………………………Eqn. 7.23
( ) ZRT
bNb
RTbN
ZdRT
bNdbbd
RTbNT
AA
AA
ln5.9
1ln45.9
ln5.91
45.9
0002
++−+−
=
++
−
−
−= ∫∫∫
ρε
ρρε
ρε
ρρ
ρρ
ε ρρρ
( ) ZbRT
bNRT
AA Aig
ln1ln45.9−−−
−=
−⇒ ρρε
or by using Eqn. (7.25)
( ) ZbRT
bNRT
AA
ZdRT
bNd
bb
RTAA
ZdZRT
AA
Aig
Aig
ig
ln1ln45.9
ln5.9
14
ln1
00
0
−−−−
=−
⇒
−−−
=−
⇒
−
−=
−⇒
∫∫
∫
ρρε
ρε
ρρ
ρρ
ρρ
ρ
(P7.5) Compute ∆H,∆S,∆U,∆V of 1,3 butadiene from 25bar,400K to 125bar,550K.
For State 2: T (K) 550 Z V H-Hig U-Uig S-SigP (MPa) 12.5 cm3/gmol J/mol J/mol J/molK & for 1 root region 0.67898224 248.3825681 -8054.423 -6586.505 -11.10052
State 1 has three real roots. Take the more stable root (lower fugacity value).For State 1 T (K) 400 Z V fugacity H-Hig U-Uig S-SigP (MPa) 2.5 cm3/gmol MPa J/mol J/mol J/molKanswers for three 0.668475 889.2328 1.871218 -3460.25 -2357.73 -6.24206root region 0.180657 240.3178 0.103098 137.145 2.008636 -14993.7 -12011 -35.6649
Chapter 7 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics© J.R. Elliott, C.T. Lira, 2001, all rights reserved. (3/10/2007) 4 of 5
( ) ( ) ( )( ) ( ) ( )igigigig
igigigig
SSSSSSSSS
HHHHHHHHH
11122212
11122212
−−−+−=−=∆
−−−+−=−=∆
Find ??12 =− igig HH
( ) ( ) ( ) ( )41
42
31
32
21
2212
3212
432
)(2
1
2
1
TTDTTCTTBTTA
dTDTCTBTACpdTHHT
T
T
T
igig
−+−+−+−=
+++==−⇒ ∫∫
A B C D-1.687 3.42E-01 -2.34E-04 6.34E-08
moleJHH igig /81.1717312 =−⇒
Similarly for ∫ −=−2
1 1
212 ln
T
T
igig
PP
RdTTCpSS
( ) ( ) ( )
−
−+−+−+
=−⇒
1
231
32
21
2212
1
212 ln
32ln
PP
RTTDTTCTTBTT
ASS igig
KmoleJSS igig −=−⇒ /87.2212
KmoleJSmoleJH−=∆
=∆⇒/01.18&
/63.12579
( )12
2
1
)( TTRHdTTCvUT
T
−−∆==∆ ∫ , RCpCv −=
( )( ) ( ) ( )
moleJUU
UUUUUUUUU
moleJUUigigigig
igig
/94.1169773.2357505.658671.15926
&
/71.15926400550*314.881.17173
11122212
12
=∆⇒+−=∆⇒
−−−+−=−=∆
=−−=−
molcmV
VVV
/8.640
2.8894.2483
12
−=∆⇒
−=−=∆
(P7.6) Ethane tank leaks to turbine: molesnmVMPaPKT 28301,10,425 311 =⇒=== ;
Solution: Ebal: ∆H=W; Sbal: ∆S=0.(a) Compute ToutInitial. Sout=Sin=78.2J/Mol-K<79.7=SsatVap(1bar)⇒ Tout=184.2K(b) Compute Winitial = ∆H; q=78.2/79.7=98% ⇒ Hout=0.98*14676=14383W = 14382-24087= -9705J/mol (FYI: given answer at 8880 probably used SRK.)
Chapter 7 Practice Problems
To accompany Introductory Chemical Engineering Thermodynamics© J.R. Elliott, C.T. Lira, 2001, all rights reserved. (3/10/2007) 5 of 5
(P7.7) Compute W for 80% eff turbine on Ethylene from 350°C,50bar to 2bar. Compare Tf forthis process to Tf of 100%eff turbineSolution: Ebal: ∆H=W; Sbal: 12 SS =′ =9.1954; Ref=298.15K,1bar, id gas.T (K) 623.15Z V H U SP (MPa) 5 cm3/gmol J/mol J/mol J/molK
& for 1 root region 0.986361 1022.041 18750.12 13639.92 9.1954For Rev: Use Solver at 0.2MPa and S2’=9.1954J/mol-K then we can find HandH ∆′∆
T (K) 404.71Z V H U SP (MPa) 0.2 cm3/gmol J/mol J/mol J/molK
& for 1 root region 0.99499 16739.56 5234.912 1887 9.1954
molJH
HHHHH
WW
HH
moleJH
s
s
/95.793712.18750912.5234
12.187508.0
8.08.0
/21.1351512.18750912.5234
2
2
12
12
=⇒−
−=⇒
−′−
=′
==′∆
∆⇒=
−=−=′∆
η
molJHHHH
/166.1081212.1875095.793712
=∆⇒−=−=∆⇒
T (K) 452.012672 fugacity H U SP (MPa) 0.2 MPa J/mol J/mol J/molK
& for 1 root region 0.199324 7937.95 4192.62 15.50748631KT 4522 =⇒
(P7.8) Rankine on methanol, see figure 4.3 page 143. Ref=336.7,0.1Liq.State T(K) P(Mpa) H S4’sat vap 337.4 0.1027 37853 112.165 sat liq 337.4 0.1027 73 0.233 610 4.087 51458 112.16
2647.0)7351458(
)3785351458(=
−−
=−
=HQWη (Note: neglecting pump work.)
(P7.9) Use the energy equation to get (U-Uig)/RT.a. For SW fluid for g=10-5x. x=r/σ;
( )5.1
1
4332
5.1
1
32
0 45
310
244)510(
24
2
−
−=−
−==
−∫∫
∞ xxTk
NdxxxTk
NdrrrgRT
uNNRT
UU
B
A
B
AAAig πρσεπρσεπρ
NAρσ3 = 1; ε/kBT = 1 ⇒ (U-Uig)/RT = -5.7π.b. For Sutherland potential with g = 1+2/x2.
( )∞−−∞∞
−
−−=
+
−==
−∫∫
1
533
6
2
12
32
0 52
424421
24
2xx
TkNdx
xx
xTkNdrrrg
RTuNN
RTUU
B
A
B
AAAig πρσεπρσεπρ NAρσ3
= 1; ε/kBT = 1 ⇒ (U-Uig)/RT = -3π.
Chapter 9 Practice Problems (p9.01) The stream from a gas well consists of 90 mol% methane, 5% ethane, 3% propane and 2%
n-butane. This stream is flashed isothermally at 233 K and 70 bar. Use the shortcut K-ratio method to estimate the L/F fraction and liquid vapor composisitons. (ANS. L/F = 0.181) …
Solution By short-cut vapor pressure eqn.
yx
KT
Pi
ii
ii
r i
= ≅
+ −FHGIKJ
LNM
OQP
LNMM
OQPP
10 73
1 1 1^?,
,
ωa f
y x Ki i i= Though not required, the table below also shows bubble T and dew T calculations at 70 bar. For the bubble calculations, in each column, the temperature at the top of the column is used to
calculate the K-ratio. Then yi = xiKi. The temperature is adjusted until the sum of y’s is unity. This is an iterature calculation.
To accompany Introductory Chemical Engineering Thermodynamics 1 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
For the dew T calculations, in each column, the temperature at the top of the column is used to calculate the K-ratio. Then xi = yi/Ki. The temperature is adjusted until the sum of x’s is unity. This is an iterative calculation.
For the isothermal flash calculation, the T = 233K and the pressure is 70 bar, so the K-ratio is
fixed, as tabulated in the column under ‘233’. Equation 9.63 is programmed in the cells below the value of L/F=0.181 below the ‘Flash’ title. Each row holds the value of the term ‘Di = zi(1-Ki)/[Ki + (L/F)(1-Ki)]’ from equation 9.63. These values are summed at the bottom of the column. The criteria for the isothermal flash is that L/F is adjusted until the sum goes to zero, as is shown at L/F = 0.181. Once the value of L/F is found, the xi values and yi values in the last columns are generated separately using equations 9.57 and 9.58 respectively.
pMPa= 7.000 BUBT DEWT FLASH
z Tc Pc w 210.9 y 300.5 x 233 0.181 x yC1 0.9 190.6 4.6 0.011 1.108 0.997 4.7949 0.188 1.767 -0.424 0.553 0.977C2 0.05 305.4 4.88 0.099 0.049 0.002 0.6332 0.079 0.111 0.1632 0.184 0.020C3 0.03 369.8 4.25 0.152 0.006 0.000 0.1456 0.206 0.016 0.152 0.155 0.002nC4 0.02 425.2 3.8 0.193 8E-04 0.000 0.0379 0.527 0.003 0.1088 0.109 0.000
1.0000 0.9997 5E-07 1.000 1.000
To accompany Introductory Chemical Engineering Thermodynamics 2 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
(p9.2) An equimolar mixture of n-butane and n-hexane at pressure is isothermally flashed at 373K. The liquid-to-feed ratio is 0.35. Use the shortcut K-ratio method to estimate the pressure and liquid and vapor compositions. (ANS. P=0.533MPa; xC6=0.78). Solution By short-cut vapor pressure eqn.
yx
KT
Pi
ii
ii
r i
= ≅
+ −FHGIKJ
LNM
OQP
LNMM
OQPP
10 73
1 1 1^?,
,
ωa f
y x Ki i i= For the isothermal flash calculation, the T = 373K. Equation 9.63 is programmed in the cells
below the value of L/F=0.35 below the ‘Flash’ title. Each row holds the value of the term ‘Di = zi(1-Ki)/[Ki + (L/F)(1-Ki)]’ from equation 9.63. The value of Ki requires P which is to the left of the table. These values are summed at the bottom of the column. The criteria for the isothermal flash is that P is adjusted until the sum goes to zero, as is shown at P = 0.533. Once the value of P is found, the xi values and yi values in the last columns are generated separately using equations 9.57 and 9.58 respectively.
To accompany Introductory Chemical Engineering Thermodynamics 3 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
Though not required, the table below also shows the bubble T and dew T calculations for P = 0.533 MPa.
For the bubble calculations, in each column, the temperature at the top of the column is used to calculate the K-ratio. Then yi = xiKi. The temperature is adjusted until the sum of y’s is unity. This is an iterature calculation.
For the dew T calculations, in each column, the temperature at the top of the column is used to
calculate the K-ratio. Then xi = yi/Ki. The temperature is adjusted until the sum of x’s is unity. This is an iterative calculation.
pMPa= 0.533 BUBT DEWT FLASHz Tc Pc w 349.2 y 383.2 x 373 0.35 x y
nC4 0.5 425.2 3.8 0.193 1.766 0.883 3.5299 0.142 2.906 -0.426 0.223 0.649nC5 0 469.7 3.37 0.249 0.624 0.000 1.3902 0.000 1.11 0 0.000 0.000nC6 0.5 507.4 3.01 0.305 0.236 0.118 0.5826 0.858 0.452 0.4257 0.777 0.351nC7 0 540.3 2.74 0.349 0.097 0.000 0.2631 0.000 0.199 0 0.000 0.000
1.0010 0.9999 1E-06 1.000 1.000
To accompany Introductory Chemical Engineering Thermodynamics 4 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
(p9.3) A mixture of 25 mol% n-pentane, 45% n-hexane, and 30% n-heptane is flashed isothermally at 365.9K and 2 bar. Use the shortcut K-ratio method to estimate the L/F fraction and liquid and vapor compositions (ANS. L/F = 0.56) … By short-cut vapor pressure eqn.
yx
KT
Pi
ii
ii
r i
= ≅
+ −FHGIKJ
LNM
OQP
LNMM
OQPP
10 73
1 1 1^?,
,
ωa f
y x Ki i i= Though not required, the table below also shows bubble T and dew T calculations at 2 bar. For the bubble calculations, in each column, the temperature at the top of the column is used to
calculate the K-ratio. Then yi = xiKi. The temperature is adjusted until the sum of y’s is unity. This is an iterature calculation.
For the dew T calculations, in each column, the temperature at the top of the column is used to
calculate the K-ratio. Then xi = yi/Ki. The temperature is adjusted until the sum of x’s is unity. This is an iterative calculation.
To accompany Introductory Chemical Engineering Thermodynamics 5 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
For the isothermal flash calculation, the T = 365.9 K and the pressure is 2 bar, so the K-ratio is fixed, as tabulated in the column under ‘365.9’. Equation 9.63 is programmed in the cells below the value of L/F=0.56 below the ‘Flash’ title. Each row holds the value of the term ‘Di = zi(1-Ki)/[Ki + (L/F)(1-Ki)]’ from equation 9.63. These values are summed at the bottom of the column. The criteria for the isothermal flash is that L/F is adjusted until the sum goes to zero, as is shown at L/F = 0.56. Once the value of L/F is found, the xi values and yi values in the last columns are generated separately using equations 9.57 and 9.58 respectively.
pMPa= 0.2 BUBT DEWT FLASH
z Tc Pc w 358.6 y 312.48 x 365.9 0.56 x ynC4 0 425.2 38 0.193 57.73 0.000 18.804 0.000 67.18 0 0.000 0.000nC5 0.25 469.7 3.37 0.249 2.107 0.527 0.5756 0.434 2.51 -0.227 0.150 0.377nC6 0.45 507.4 3.01 0.305 0.821 0.369 0.1898 2.370 1.001 -2E-04 0.450 0.450nC7 0.3 540.3 2.74 0.349 0.348 0.104 0.0694 4.324 0.432 0.227 0.400 0.173
1 7.129 3E-08 1.000 1.000
To accompany Introductory Chemical Engineering Thermodynamics 6 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
(p9.04) A mixture containing 15 mol% ethane, 35% propane, and 50% n-butane is isothermally flashed at 9 bar and T. the liquid-to-feed ratio is 0.35. Use the shortcut K-ratio method to estimate the pressure and liquid and vapor compositions. By short-cut vapor pressure eqn.
yx
KT
Pi
ii
ii
r i
= ≅
+ −FHGIKJ
LNM
OQP
LNMM
OQPP
10 73
1 1 1^?,
,
ωa f
y x Ki i i= For the isothermal flash calculation, the P=9 bar. Equation 9.63 is programmed in the cells
below the value of L/F=0.35 below the ‘Flash’ title. Each row holds the value of the term ‘Di = zi(1-Ki)/[Ki + (L/F)(1-Ki)]’ from equation 9.63. The value of Ki requires T which is to the left under the ‘Flash’ title. These values of Di are summed at the bottom of the column. The criteria for the isothermal flash is that T is adjusted until the sum goes to zero, as is shown at T = 319.4K. Once the value of T is found, the xi values and yi values in the last columns are generated separately using equations 9.57 and 9.58 respectively.
Though not required, the table below also shows the bubble T and dew T calculations for P = 0.9
MPa.
To accompany Introductory Chemical Engineering Thermodynamics 7 of 8 © J.R. Elliott, C.T. Lira, 2004, all rights reserved, (3/17/04)
For the bubble calculations, in each column, the temperature at the top of the column is used to calculate the K-ratio. Then yi = xiKi. The temperature is adjusted until the sum of y’s is unity. This is an iterature calculation.
For the dew T calculations, in each column, the temperature at the top of the column is used to
calculate the K-ratio. Then xi = yi/Ki. The temperature is adjusted until the sum of x’s is unity. This is an iterative calculation.
pMPa= 0.900 BUBT DEWT FLASHz Tc Pc w 290 y 326.9 x 319.4 0.35 x y
C1 0 190.6 4.6 0.011 32.92 0.000 49.257 0.000 45.74 0 0.000 0.000C2 0.15 305.4 4.88 0.099 3.963 0.594 7.9952 0.019 7.027 -0.184 0.031 0.214C3 0.35 369.8 4.25 0.152 0.86 0.301 2.0955 0.167 1.779 -0.181 0.232 0.413nC4 0.5 425.2 3.8 0.193 0.213 0.106 0.614 0.814 0.505 0.3648 0.737 0.372
1.0016 1.0002 6E-08 1.000 1.000
4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 90 TEST 1 SSN________ 1. Short Answer a) Estimate the change in entropy when one mole of nitrogen is compressed by a piston in a cylinder from 300K and 23 liters/gmol to 400K and 460 liters/gmol.(Cp=7 cal/gmol) b) Draw a sketch of the square well potential and indicate the position(s) where the force between two atoms is zero. c) Write the simplest possible form of the energy balance for application to the following process and system: water drips slowly out of a hole in the bottom of an enclosed tank; system: the tank and its contents. d) Write the simplest possible form of the energy balance for application to the following process and system: a rubber balloon being inflated; system: the balloon and its contents. 2. Estimate the density (g/cc) of liquid butane at 300 K and 38 psia. Assuming that a disposable lighter costs $1.00 and contains 2 g of butane, what is the value of the butane? ($/gal) 3. Saturated steam at 660°F is adiabatically throttled to atmospheric pressure. Estimate the final condition of the steam. 4. A mixture of 1CO:2H2 is adiabatically continuously compressed from 5 atm and 100°F to 100 atm and 1100°F. Estimate the work of compressing 1 ton of the gas.(Cp=7Btu/lbmol-R) 5. Determine the efficiency of the compressor in problem 4. 6. An insulated cylinder is fitted with a freely floating piston and contains 1 lbm of steam at 120 psia and 90% quality. The space above the piston, initially 1 ft3, contains air at 300 K to maintain the pressure on the steam. Additional air is forced into the upper chamber, forcing the piston down and increasing the steam pressure until the steam has 100% quality. The final steam pressure is 428 psia and the work done on the steam is 91 Btu, but the air above the steam has not had time to exchange heat with the piston, cylinder or surroundings. The air supply line is at 700 psia and 300 K. What is the final temperature of the air in the upper chamber? 1a)7.4cal/mol-K (c)HdM=d(MU) (d)HdM+W=d(MU) 2).6 g/cc 3) 0.96 4) 1.3E6 5) 76% 6)360K 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 91 TEST 1 SSN________ 1. Short Answer a) 15 molecules are distributed as 9:4:2 between boxes A:B:C respectively. The partitions between the boxes are removed and the molecules distribute themselves evenly between the boxes. Compute ∆S. b) Explain in words how the pressure of a fluid against the walls of its container is related to the velocity of the molecules. c) What is it about molecules that requires us to add heat to convert liquids to gases? d) A rigid cylinder of gaseous hydrogen is heated from 300K and 1 bar to 400K. How much heat is added to the gas? 2. Steam is produced at 30 bar and some unknown temperature. A small amount of steam is bled off and goes through an adiabatic throttling valve to 1 bar. The temperature of the steam exiting the throttling valve is 110°C. What is the value of the specific entropy of the steam before entering the throttle? 3) An adiabatic compressor is used to continuously compress nitrogen (Cp/R=7/2) from 2 bar and 300K to 15 bar. The compressed air is found to have an outlet temperature of 722K. How much work is required? 4) What is the efficiency of the compressor in the previous problem? 5) As part of a supercritical extraction of coal, an initially evacuated cylinder is fed with steam from a line available at 20 MPa and 400°C. What is the temperature in the cylinder immediately after filling? Answers: 1.a)2.31k 1.b)change of direction due to wall collision gives change in velocity per unit time providing the acceleration in the force per unit area that is pressure. 1.c)potential energy causes them to stick together when close to each other. 1.d)2079 J/mol. 2)5.9736kJ/kg-K 3)436J/g 4)53%5)454°C 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 92 TEST 1 SSN________ 1. Short Answer a) How does heat get from the flame of a gas oven into a pizza inside the oven? b) Nitrogen (Cp/R=7/2) is adiabatically and reversibly compressed from 300K and 5 bar to 25 bar. Compute the temperature coming out of the compressor. c) Estimate the S of liquid freon-12 at -40°F.(Hint: use chart) d) In a large refrigeration plant it is necessary to compress a fluid which we will assume to be an ideal gas with constant heat capacity, from a low pressure P1 to a much higher pressure P2. If the compression is to be done in two
2stages, first compressing the gas from P1 to P*, then cooling the gas at constant pressure down to the compressor inlet temperature T1, and then compressing the gas to P2, what should the value of the intermediate pressure be to accomplish the compression with minimum work? (Hint: don't derive the whole formula. If you know the answer, just write it down.) 2. An adiabatic compressor is used to continuously compress low pressure steam from 0.8 MPa and 200°C to 4.0 MPa and 500°C in a steady state process. What is the work required per kg of steam through this compressor? 3) Compute the efficiency of the compressor in the previous problem. 4) An ordinary vapor compression cycle is to operate a refrigerator on F-12 between -40°F and 120°F (coil temperatures). Compute the coefficient of performance and the heat removed from the refrigerator per day if the power used by the refrigerator is 9000 J per day. 5) Airplanes are launched from aircraft carriers by means of a steam catapult. The catapult is a well-insulated cylinder that contains steam and is fitted with a frictionless piston. The piston is connected to the airplane by a cable. As the steam expands, the movement of the piston causes movement of the plane. A catapult design calls for 270 kg of steam at 15 MPa and 450°C to be expanded to 0.4 MPa. How much work can this catapult generate during a single stroke? Compare this to the energy required to accelerate a 30,000 kg aircraft from rest to 350 km per hour. Answers:1.a)air collisions b)475K c).0024 d)√P1P2 2)606kJ/kg 3)67% 4)1.55,-14,000J/day 5)165224 kJ vs. 141782 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 93 TEST 1 SSN________ 1. Short Answer a) 20 molecules are contained in a piston+cylinder at low pressure. The piston moves such that the volume is expanded by a factor of 4 with no work produced of any kind. Compute ∆S/k. b) A tank of N2 (Cp=7R/2) at 300K and 25 bars leaks adiabatically until the pressure drops to 5 bar. What is the final temperature?. c) A Carnot cycle is to operate with coil temperatures from -160°F to -280°F. Compute the coefficient of performance. d) As part of the air standard Otto cycle, air (Cp=7R/2) in a cylinder at 400K is compressed adiabatically and reversibly with a volumetric compression ratio of 8:1. Develop an expression relating the work required for a given compression ratio in terms of the temperatures T1 and T2 (ie. the temperatures before and after).(Hint: No numbers are necessary in your "expression".) e) A tank of air (Cp=7R/2) drives an adiabatic, reversible turbine exhausting to the atmosphere. Derive an overall entropy balance between the specific entropy of air exiting the turbine vs. the specific entropy in the tank. 2. An adiabatic turbine is supplied with steam at 2.0 MPa and 600°C and it exhausts at 98% quality and 24°C. Compute the work output per kg of steam.(15) 3. Compute the efficiency of the turbine in problem 2.(20) 4. An ordinary vapor compression cycle is to be operated on methane to cool a chamber to -260°F. Heat will be rejected to liquid ethylene at -165°F. The temperatures in the coils are -160°F and -280°F. Compute the coefficient of performance. (Hint: Use Chart )(20) 5. A well-insulated cylinder, fitted with a frictionless piston, initially contained 9 kg of liquid water and .4 kg of water vapor at a pressure of 1.4 MPa. 2 kg of steam at 1.6 MPa was admitted to the cylinder while the pressure was held constant by allowing the piston to expand. a) Write the energy balance for this process. (10) b) If the final volume of the contents of the cylinder was six times the initial volume, determine the temperature of the superheated steam that was admitted to the cylinder.(10). 1a)23.2(b)189(c)1.5(d)Cv∆T(e) ∆S =0(2)-1194J(3)85%(4).86(5) ∆MU=W+H∆M,557°C 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 94 TEST 1 SSN________ 1. Short Answer a) Rolling two dice (six sided cubes with numbers between 1 and 6 on each side) is like putting two particles in six boxes. Compute ∆S/k for going from double sixes to a four and three.0.693 b) Air (Cp/R=3.5) is isothermally compressed in a piston+cylinder from 100°C and 1 bar to 100 bar. Estimate the work requirement in J/mole.14000
3c) Air (Cp/R=3.5) is adiabatically and reversibly compressed in a piston+cylinder from 100°C and 1 bar to 100 bar. Estimate the work requirement in J/mole.21000 d) Suppose a particular charge of gunpowder resulted in a high pressure gas at 100 bar and 3000K in a 10 cm dia X 20 cm length chamber. This chamber is connected to 480cm barrel of the same diameter angled at 45°. Assuming that the mass of the cannonball is 1 kg and the expansion of the gas is adiabatic and reversible, write the energy balance for the travel of the cannonball from its initial position to the end of the gun barrel. (You do not need to substitute any numbers.) Wdt=d[M(U+v2/2+gZ)] e) A series of three adiabatic, reversible compressors with interstage cooling to the initial inlet temperature is to compress air (assume ideal gas) from 300K and 1 bar to 100 bar. Estimate the pressure after the first compression stage assuming the series has been designed to minimize the overall work requirement. 4.6bar 2. An adiabatic compressor has been designed to continuously compress 1 kg/s of saturated vapor steam from 1 bar to 100 bar and 1100 C. Estimate the power requirement of this compressor in horsepower. (15)3000 3. Determine the efficiency of the compressor described above. (20)60 4. A cold storage room is to be maintained at 10°F and the available cooling water is 70°F. Assume that the cold-room coils and the condenser are of sufficient size that a 10°F approach can be realized in each. The refrigerant capacity is to be 126,500 kJ/hr. Freon-22 (!!!) will be used for the vapor compression cycles. Calculate the COP for the following cases: a) Carnot cycle (5)5.75 b) Ordinary vapor compression cycle for which compressor is 100% efficient.(10)4.3 c) Ordinary vapor compression cycle for which compressor is 80% efficient.(5)3.4 (Note: This is Freon-22. Minimal credit will be awarded for Freon-12. 5. A 1 m3 tank is to be filled using N2 at 300K and 20 MPa. Instead of throttling the N2 into the tank, a reversible turbine is put in line to get some work out of the pressure drop. If the pressure in the tank is initially zero and the final pressure is 20 MPa, what will be the final temperature in the tank? How much work will be accomplished over the course of the entire process? (Hint: consider the entropy balance carefully.)(20)300K,20E6J 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 96 TEST 1 SSN________ 1. Short Answer (20) a) Two moles of oxygen are mixed with an equal volume of nitrogen at 300K and 1 bar. Estimate (assuming ideal gas) the change in entropy (J/mole-K) for the oxygen. b) Saturated liquid water at 25°C is steadily pumped to a pressure of 70 bars. Estimate the work requirement in J/g. c) An initially evacuated cylinder of hydrogen is to be filled from a supply line available at 400K and 50 bars. Estimate the final temperature (K) of the hydrogen in the cylinder after filling. d) Write the most compact but applicable energy balance for the following: A surge tank is mounted at the side of an air supply line to damp out fluctuations in the air pressure. As the pressure in the supply line begins to drop, air leaks out of the surge tank into the supply line. System: the surge tank and its contents. 2) Freon-22 is adiabatically compressed in a steady state process from saturated vapor at 240K to 15 bars and 400K. Compute the specific work required (kJ/kg).(20) 3) Estimate the efficiency of the compressor from the above problem.(20) 4) A heat engine is to operate on steam. Cooling water is available such that the condenser operates at a temperature of 50°C. The manufacturer of the boiler specifies that the temperature of the steam exiting the boiler may not exceed 400°C. The manufacturer of the turbine requires that the quality of steam exiting the turbine must be at least 89.5%. a) Estimate the maximum thermal efficiency of a Carnot cycle operating between these upper and lower temperatures.(5) b) Estimate the maximum thermal efficiency of a single stage Rankine cycle operating between these upper and lower temperatures.(20) 5) Suppose the fluid in the fix-a-flat can was Freon-22 (MW=85.5) at 50wt% liquid and 100kg/m3. Let the can be 500 cm3 and the tire be 40,000 cm3 at 300K and 1 bar. a) write the mass balance for the overall process (2). b) write the energy balance for the overall process (2). c) write the entropy balance for the can of Freon-22 (2). d) Approximating that the tire was originally filled with Freon-22, that the contents of the tire are at such a low
pressure that they can be treated as an ideal gas, and that the change in the temperature of the tire is negligible,
4solve for the tire pressure (bars) when the pressure in the can has dropped to 4 bars. Is it enough to inflate the tire? (9)
Answers: (1)a. 11.5J/mole-K, b.7J/g, c.560K, d.Houtdn=d(nU) (2) 100J/g (3)64 (4)52%,30% (5) a.mCf + mTf = mCi + mTi b. mCf UCf+ mTf UTf = mCi UCi + mTi UTi c.∆S=0 d.1.25bars 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 97 TEST 1 SSN________ 1. Short Answer (15) a) The specific volume of steam at 4 MPa and 1200°C in m3/kg is ______ m3/kg b) A 2000 kg automobile traveling at 25 m/s strikes a plunger in 10,000 cm3 of water, bringing the auto to a stop.
What is the maximum temperature rise, in °C, of the water? c) Find the work, in kJ/kg needed to compress air isentropically from 20°C and 100 kPa to 6 MPa (in a
piston+cylinder). 2. Consider the case of 8 particles distributed between two boxes. What is the fraction of microstates with 4
particles in the first box and 4 particles in the second box? (10) 3. As part of a refrigeration cycle, Freon 134a is adiabatically compressed from the saturated vapor at -60°C (note the negative sign on temperature) to 1017kPa and 100°C. How much work is required in kJ/kg?(15) 4. Estimate the efficiency of the compressor in problem 3.(20) 5. A Rankine cycle is to be operated on steam entering the turbine at 500°C and 5MPa and expanding isentropically to 10kPa. a) Estimate the maximum work output in kJ/kg.(10) b) Estimate the maximum thermodynamic efficiency for this cycle. (10) 6. We have an isothermal 100% efficient, continuous compressor to raise steam from 0.5 MPa to 5 MPa. The process of interest involves a fluidized bed reactor that requires a volumetric flow rate of 0.1 m3/sec to maintain the fluidization. The stoichiometry for the reaction of interest requires that 1.73 kg/sec of steam be fed to the reactor. a) Write the appropriate reduced energy and entropy balances for the compressor.(6) b) Determine the temperature at which the compressor should operate. (4) c) Determine the work requirement in horsepower of the compressor. (10) Answers: (1)0.17,15°C,466,(2).27(3)121(4)75%(5)1224,38%(6)∆S=∆Q/T,400°C,1616hp 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 98 TEST 1 SSN________ 1. Short Answer (35)
Sketch the force between two molecules vs. dimensionless distance, r/σ, according to the Lennard-Jones potential. Is the value of r/σ when the force is equal to zero greater, equal, or less than unity?(5) Estimate the change in entropy (J/mole-K) when 0.5 moles of helium are mixed with 0.5 moles of hydrogen at 300K.(5) Estimate the "lost work" of the process in part c above.(5) Estimate the work required (J/mole) to adiabatically and reversibly compress argon from 1 bar and 300 K to 20 bars in a steady state process. (10) Ten particles distributed between two boxes go from 9 in box A to 6 in box A. Compute the change in entropy (dimensionless ∆S/k will suffice).(10)
2. Steam expands through an adiabatic turbine from 200 bars and 700°C to 1 bar saturated vapor. Compute the work output of the turbine in kJ/kg. (15)
3. Compute the efficiency of the turbine in problem 3.(15) 4. Freon 134a is used in an OVC heat pump providing cooling to a building during the summer. The air inside the
building is to be maintained at 25°C with a 5°C approach temperature (cf. Index for definition of approach temperature) and the heat is to be rejected to the outside air at 35°C with a 25°C approach. The compressor is 80% efficient. Compute the coefficient of performance for this cycle and compare it to the value for a Carnot cycle.(20)
55. It is desired to determine the volume of an initially evacuated tank by filling it from an 80 liter cylinder of air at
300 bars and 300K. The final pressure of both tanks is 5 bars. Estimate the volume in liters.(15) Answers: 1(a) greater (b) 5.763J/mol-K (c) 1729J/mol (d) 14432 J/mol, 2. 3.04*kB 3. 1133kJ/kg 4. 83% 5. 4.24vs.7.3 6. 4720L 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 99 TEST 1 SSN________ 1. Short Answer (25) a) Derive the expression for the force between two molecules characterized by the Yukawa potential (given
below)(5)
≥−−
−
<∞=
σσ
σε
σ
rr
rBr
ru)/(
]}1)/[(exp{)(
b) Estimate the change in entropy (J/mole-K) when 0.25 moles of helium are mixed with 0.75 moles of hydrogen at 300K. (5)
c) Estimate the "lost work" of the process in part b above.(5) d) Nitrogen is adiabatically and reversibly expanded from 300 Kelvin and 1 bar to 1 Kelvin. Estimate the
downstream pressure.(10) 2. Twenty particles are distributed between two boxes with 13 in box A. Compute the number of microstates for
this macrostate and the fraction of all microstates associated with this macrostate.(10) 3. Freon 134a expands through an adiabatic turbine from saturated vapor at 70°C to -30°C saturated vapor.
Compute the work output of the turbine in kJ/kg. (15) 4. Compute the efficiency of the turbine in problem 3.(15) 5. Steam is used in an OVC heat pump providing cooling to a space station on Mars. The saturated liquid water
exits the condenser at 295°C. The saturated vapor exits the evaporator at 30°C. The adiabatic compressor is 80% efficient. Compute the coefficient of performance for this cycle and compare it to the value for a Carnot cycle.(20)
6. Saturated liquid Freon 134a at 296K is used in a fix-a-flat can starting filled with 300 g of saturated liquid and dropping to 2.42 bars.
(a) What is the quality of the Freon in the can at the end of the process (10) (b) How many moles of Freon 134a (MW=102) are left the can? (5) 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 2000 TEST 1 SSN________ 1. Short Answer (20) a. Write the simplified energy balance for the following: A pot of water brought to a boil from
initially cold water in a pressure cooker on the oven with the pressure relief valve operating perfectly. System: the pot and its contents.(5)
b. Molecules A and B can be represented by the square-well potential. For molecule A, σ = 0.3 nm and ε = 10e-22 J. For molecule B, σ = 0.5 nm and ε = 30e-22 J. Which molecule would you expect to have the higher boiling temperature?(5)
c. Molecules A and B can be represented by the square-well potential. For molecule A, σ = 0.3 nm and ε = 10e-22 J. For molecule B, σ = 0.5 nm and ε = 30e-22 J. Sketch the potential models for the two molecules on the same pair of axes clearly indicating σ's and ε's of each specie. Make molecule A a solid line and B a dashed line.(5)
d. Argon in a rigid cylinder at 300 K and 100 bars leaks adiabatically to a pressure of 25 bars. Estimate the temperature of the argon remaining the tank. (5)
62. A Rankine cycle operates on steam exiting the boiler at 7 MPa and 550°C and dropping to 60°C and 98%
quality. (a) Compute the efficiency of the turbine.(10) (b) Estimate the pump work (kJ/kg).(5) (c) Compute the thermal efficiency of the Rankine cycle.(5) (d) Compute the thermal efficiency of a Carnot cycle operating between 550 and 60°C.(5)
3. 200 moles per hour of natural gas is to be adiabatically and reversibly compressed from 300K and 1 bar to 100
bars in a continuous two-stage process with inter-cooling to 300K. Natural gas may be approximated by pure ideal gas methane. (a) What pressure do you recommend between stages? (5) (b) Estimate the final temperature exiting the second stage. (5) (c) Estimate the work requirement (kJ/mole) (6) (d) Estimate the average power requirement for the compressor (hp). (4)
4. Freon 134a is to be adiabatically and reversibly compressed from saturated vapor at -25°C to 3MPa.
(a) Compute the work requirement (kJ/kg) using the chart. (5) (b) Compute the heat removed in a condenser(QH) that drops the outlet of the above compressor to saturated liquid. (5) (c) Compute the Coefficient of Performance (QL/W) for an OVC cycle based on this compressor and condenser. (5)
5. Steam originally exists in a piston +cylinder at 0.4 MPa and 350°C. The piston is forced down adiabatically and
reversibly till the volume is 38% of the original volume. (a) Write the energy and entropy balances for this process (6). (b) Estimate the final pressure and temperature. (6) (c) Compute the work for this process (kJ/kg) (8).
6. A rigid insulated cylinder is initially divided into two compartments by a frictionless piston that does not
conduct heat. Initially, the piston separates two ideal gases (Cv/R=2 for both gases). The entire system is initially at 300K. One gas is at 200 bars and occupies 10% of the total fixed volume and the other is at 20 bars. The piston is attached to a rod such that work is adiabatically and reversibly removed as the two sides of the piston equilibrate. (a) What is the relationship between volume and pressure on each side of the piston? (5) (b) What is the ratio of the final volumes and what are the final temperatures for each gas at equilibrium? (15) (c) If the piston were able to conduct heat, but the process was conducted irreversibly, such that no work was removed, what would be the final states (P,V,T) of both sides of the piston at equilibrium? (10)
4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 87 TEST 2 SSN________ 1) True or false.
____The compressibility factor Z is always less than or equal to unity.
____The critical properties Tc and Pc are constants for a given compound.
____A closed system is one of constant volume.
____A steady-state flow process is one for which the velocities of all streams may be assumed negligible.
____Gravitational potential-energy terms may be ignored in the steady-state energy equation if all streams entering and leaving the control volume are at the same elevation.
____In an adiabatic flow process, the entropy of the fluid must increase as the result of any irreversibilities within the system.
____The temperature of a gas undergoing a continuous throttling process may either increase or decrease across the throttling device, depending on conditions.
____When an ideal gas is compressed adiabatically in a flow process and is then cooled to the initial temperature, the heat removed in the cooler is equal to the work done by the compressor. (Assume potential and kinetic energy effects are negligible.)
____In the limit as P→ 0, the ratio f/P for a gas goes to infinity, where f is the fugacity.
____The residual Gibbs function is related to f/P by (G-Gid)/(nRT)=ln(f/p).
2) Reduce (∂H/∂S) to a form involving p, V, T, Cp, Cv, and their derivatives. 3) A house has an effective heat loss of 100,000 Btu/hr. During the heating season of 160 days the
average inside temperature should be 70°F while that outside is 45 F. Freon-12 is the working fluid and an ordinary vapor-compression cycle is used. A 10 F approach on each side may be assumed. Electricity costs $0.14/KW-hr = $0.00004/Btu. a) What is the cost in $/hr if the compressor is 100% efficient? b) What is the cost if the compressor is 80% efficient?
4) Determine the horsepower required to continuously compress reversibly and adiabatically 1 lbm/min of ethylene oxide from 70°F and 1 atm to 250 psia. Cp = 12.8 cal/gmol-K; Tc = 469 K; Pc = 70.1 atm; ω= 0.200.
5) Propylene vapor is processed from 325 K and 21.35 atm to 225 K and 1 atm. Compute the change in entropy. Suppose saturated propylene vapor at 325 K is expanded reversibly and adiabatically to 1 atm. What is the final quality? Tc = 364.8 K; Pc = 45.5 atm; ω= 0.142; Cp = 14.6cal/mol-K; ln(pvap) = -2238 + 9.953 where pvap is in atm and T is in K. 1.FTFFTTTTFT 2.T(1+V/Cv(dp/dT)v ) 3.a.0.44.b.0.55 4.1.96 5.19.8cal/mol-K,90%
4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 88 TEST 2 SSN________ 1. Short Answer
a) In an ordinary vapor-compression cycle, what is the entropy after the throttle relative to the entropy before the throttle (higher, lower or equal) and why?
b) Estimate the vapor pressure of sulfur dioxide at room temperature (298K). Tc=430.8 K; p =7.78 MPa; ω=0.251
c) What is the change in entropy for an ideal gas (Cp=7 cal/mol-K) when it is raised from a temperature of 300K and pressure of .1 MPa to 320K and 5MPa?
d) After reacting H2+½O2, H2O vapor at 1500 K and 11 MPa is expanded reversibly and adiabatically through a nozzle to 0.1 MPa. Estimate the outlet temperature of this exhaust stream.
e) A two-stage compressor operates adiabatically during each stage with intercooling to 60°F between stages. We would like to compress helium (CP = 5cal/mol-K) from 1 atm to 16 atm. What pressure between stages minimizes the reversible work for the compression of this gas?
f) Develop an expression for (G-Gid)/RT as a function of bρ for a gas that can be described by: Z = 1 + 2bρ/(1-2bρ)
2. Evaluate (∂H/∂P)v in terms of only P, V, T, CP, and CV and their derivatives. Describe a physical situation to which this quantity relates.
3. Estimate the enthalpy of 1,3, butadiene at 125 atm and 530°F relative to its saturated liquid at 60F. T = 425.4 K; P = 4.33 MPa; ω = 0.193; CP =23 cal/mol-K;
4. It is desired to design a Rankine cycle using a 70% efficient turbine and expanding the steam to saturated vapor at 224°F. The boiler operates at 500 psia. Compute the thermodynamic efficiency for conversion of heat into work.(hint: neglect the pump work). Compare this to the thermodynamic efficiency of the Carnot cycle operating between the same temperatures.
5. By holding the can upside down at room temperature (298K), liquid freon-22 (MW=85.5) can be dispensed from a can through 1 ft of stainless tubing (100 g, CP =.12 cal/g-K). (a) Estimate the heat of vaporization (in cal/g) of freon-22 at its normal boiling temperature (-42°C). (b) Estimate the number of moles of freon-22 that must be wasted before the first drop of liquid comes out of the pipe if the pipe is insulated. Velocity of the vapor freon coming out of the tube may be neglected. Tc = 369.8; P = 4.97 MPa; ω= 0.221
Answers: 1)a.higher, throttling irreversible b.0.389MPa c.-7.32cal/mol-K d.585K e.4atm f.-ln(1-2bρ)+Z-1-lnZ (2)Cv(∂T/∂P)v+V (3)9443cal/mol (4)21%vs46%
4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 89 TEST 2 SSN________ 1. Estimate the entropy of 1 gmol of propane at 150°F and 200 psia. The entropy is to be taken as zero at 1 atm ideal gas and 0F.Tc =369.8 K; Pc =4.249 MPa; ω =0.152 2. Estimate the vapor pressure of isobutane at 300 K. Tc =408K; Pc =3.65MPa; ω=0.177 3. Argon (CP =5 cal/mol-K) is compressed reversibly and adiabatically in a continuous single stage process from 0.15 MPa and 300 K to 0.90 Mpa. Estimate the work done by the compressor. 4. Suppose the argon from the preceding problem was compressed from 0.15 MPa to 0.90 MPa in a two-stage process with intercooling back to 300 K. What would be the optimum interstage pressure and the work done in that case? 5. Express in terms of in terms of only P, V, T, CP, CV and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂G/∂H)P 6. The compressibility factor for a certain fluid is well-represented by: Z = 1 + abρ/(1+bρ)2 Develop an expression for the Helmholtz energy departure function. 7. Saturated vapor propane at -40°C is to be compressed to 55 atm. Estimate the work required if the compressor is adiabatic but only 50% efficient. Tc =369.8 K; Pc =4.249 MPa; ω =0.152 8. An ordinary vapor-compression cycle is to be designed for superconductor application using N2 as refrigerant. The expansion will be to atmospheric pressure. A heat sink is available at 105 K. A 5 K approach should be sufficient. Roughly 100 Btu/hr must be removed. Compute the coefficient of performance (COP) and compare it to the Carnot COP. Also, estimate the power requirement (hp) of the compressor assuming it is adiabatic and reversible. 1.-.7246cal/mol-K 2.0.3746MPa 3.-1572cal/mol 4.-1293cal/mol 5. -S/P 6. abρ/(1+bρ) 7.-3563cal/mol 8.1.33,0.30hp
4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 90 TEST 2 SSN________ 1.a. List in the space below all the differences between a Rankine cycle and a Carnot cycle. Order the list from most important to least important. 1.b. An inventor proposes to have developed a small power plant that operates at 70% efficiency. It operates between temperature extremes of 1000°F and 100°F. Develop your own analysis of the maximum possible efficiency. (Choose the power cycle that gives the highest possible value for the efficiency.) 1.c. Estimate the vapor pressure of CO2 at 14°C. (Tc=304.2K; Pc=7.381Mpa; ω =.228). 2. Estimate the quality of Freon-12 after the throttle in an ordinary vapor-compression cycle operating between -20F and 114.3F. 3. A simple Rankine cycle operates between superheated steam at 1000xF and 400 psia entering the turbine and 2 psia entering the pump. What is the maximum possible efficiency for this Rankine cycle? 4. Express in terms of in terms of only P, V, T, CP, CV and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂S/∂P)G 5. Suppose an ideal gas was continuously compressed adiabatically and reversibly from 45 psia and 70°F to 1500 psia in two stages with intercooling to 70°F between stages. What would be the optimal pressure between stages (for minimum work) and the temperature coming out of the second stage before it is cooled. (CP =13 cal/gmol-K). 6. Estimate the change in enthalpy (Btu/lbmole) when ethane at 70°F and 400 psia is compressed to 1500 psia and 120°F (Tc =305.4K; Pc =4.880MPa; ω=.099; CP =13 Btu/lbmol-R). 7. Suppose ethane was compressed adiabatically in a 70% efficient continuous compressor. The downstream pressure is specified to be 1500 psia at a temperature not to exceed 350°F. What is the highest that the upstream temperature could be if the upstream pressure is 200 psia? (Hint: neglect the departure function for the upstream thermodynamics.) Answers: 1b) 62% 1c) 5MPa 2) 42% 3) 29% 4) CpV/TS-(dV/dT)p 5) 260psia 6) -2300Btu/mol 7) 269K 4200:225 EQUILIBRIUM THERMODYNAMICS SPRING 91 TEST 2 SSN________ 1.a. The conditions of a fluid encountered in some process calculations are at a high reduced pressure and a low reduced temperature. Would this fluid have density and enthalpy similar to a gas, a vapor, a supercritical fluid or a liquid? Why? 1.b. Why does the compressibility factor increase sharply at high density? 1.c. Estimate the value of the compressibility factor, Z, for neon at Pr=30 and Tr=15. 1.d. Estimate the density of neon at Pr=30 and Tr=15.(1.2,0.26g/cc) 2. Freon-12 is used in a heat pump operating on an ordinary vapor compression cycle with a 100% efficient compressor. The average outdoor temperature is 90°F and the desired indoor temperature is 70°F. The design is such that a 40°F approach temperature is used on each side. Compute the Q /W for this process and compare it to the value you would expect for a Carnot cycle operating at the same conditions. What would be the power requirement of the compressor motor (in hp) to provide 12,000 Btu/hr of heating capacity?(1 hp=0.7074 Btu/s) 3. Propane is compressed from 1 bar and 0xC to 64 bar and 100°C. Compute the change in molar entropy, S. 4. As part of a liquefaction process, ammonia is throttled to 80% quality at atmospheric pressure. If the upstream pressure is 100 bar, what must be the upstream temperature? (Assume Cp=8.8 cal/mol-K). 5.a. For certain fluids, the equation of state is given by Z = 1 - bρ/Tr Develop an expression for the enthalpy departure function for fluids of this type. ( -2bρ/Tr) 5.b. Evaluate ( dS/dT)G in terms of only p, v, T, C , C and their derivatives. Your answer may include absolute values of S if is not associated with a derivative.
Answers: 1a.liquid 1b) close packed 1c)1.2 1d).26g/cc 2).95hp 3)-8.7cal/mol-K 4)358K 5a) 5b)Cp/T-S(dv/dT)p/V 4200:225 Eq. Thermo. SPRING 92 TEST 2 SSN_______ 1.a. Sketch the radial distribution function vs. radial distance for a low density hard sphere fluid. Describe in words why it looks like that. 1.b. The attractive contribution to the compressibility factor is:
ZkT
rdu rdr
g r dratt =− ∞
∫ρπ
σ64 2( )
Show how this expression can be rearranged into two dimensionless groups, one group which includes the effects of well-depth (ε) and size (σ) (e.g. of the Sutherland potential) and another group which is a universal constant. 1.c. Estimate the vapor pressure of ethane at 244 K. 1.d. Estimate the heat of vaporization of ethane at 244 K. 2. Ethane is continuously compressed from 280 K and 1 bar to 310 K and 75 bar. Compute the change in enthalpy per gmol of ethane. (Cp/R = 5). 3. Ethane is expanded through an adiabatic, reversible turbine from 75 bar and 310 K to 1 bar. Estimate the temperature of the stream exiting the turbine and the work per gmol of ethane. (Hint: Is the exiting ethane vapor, liquid, or a little of each?)(Cp/R = 5) 4. Evaluate (dG/dV)T in terms of p, v, T, Cp, Cv, and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. 5. Develop an expression for the departure function based on the equation of state given below such that its value may be computed given T,P, and . [G(T,p)-Gig(T,p)]/nRT where Z = 1 + bρ/(1-bρ)- aρ/RT3/2(1+bρ) (This is the Redlich-Kwong (1958)eqn. -ln(1-bρ)-a/bRT3/2ln(1+bρ)+Z-1-lnZ) 6. Our space program requires a portable engine to generate electricity for a space station. It is proposed to use sodium as the working fluid in a customized form of a “Rankine” cycle. The high temperature stream is not superheated before running through the turbine. Instead, the saturated vapor is run directly through the (100% efficient, adiabatic) turbine. The rest of the Rankine cycle is the usual. That is, the outlet of the turbine is cooled to saturated liquid which is pumped (neglect the pump work) back into the boiler. The cycle is to operate between TL =1156 K (this is the boiling temperature of sodium) and TH =1444 K.
a) Estimate the quality coming out of the turbine. b) Compute the work output per unit of heat input to the cycle, and compare it to the value for a Carnot cycle operating between the same TH and TL .
(Tc =2300 K; Pc =195 bar; ω=0 ; CP/R = 2.5) Answers: 1.c)11.2 bar d)2777 cal/mol 2)-1852cal/mol 3)-745cal/gmol 4)V(dp/dV)T 5)-ln(1-bρ)-a/bRT3/2ln(1+bρ)+Z-1-lnZ 6.a)90% b).184
4200:225 Eq. Thermo. SPRING 93 TEST 2 SSN_______ 1a. Compute the specific volume (cc/mol) of saturated liquid isopentane at 1 bar. Tc =460.4; Pc =33.84 bar; ω=.227 1b. Estimate the work (J/mol) of adiabatically and reversibly compressing saturated liquid isopentane from 0.1 MPa to 20 MPa in a continuous process. 1c. Estimate the vapor pressure (bar) of isopentane at 400K. 1d. 1 liter of air (Cp/R=3.5) at 273K is to be compressed adiabatically and reversibly in a piston+cylinder to 0.1 liter. Estimate the final temperature. (5) 2. Ammonia is to be isothermally compressed in a specially designed flow turbine from 1 bar and 100°C to 50 bar. If the compression is done reversibly, compute the heat flow needed per mole of ammonia. Tc =405.6K; Pc =112.8 bar; ω=0.250; CP/R=4.6 (20) 3. Express in terms of in terms of only P, V, T, CP, CV and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂U/∂T)A.(10) 4. Suppose u(r) is given by the square-well potential and g(r)=10-5(r/σ) for r>σ. Evaluate the internal energy departure function where NAρσ3=1 and ε/kT=1. (10) -5.7π 5. A tank containing carbon dioxide (CP/R=4.5) at 350 K and 50 bar is vented until the temperature in the tank falls to 280K. Assuming no heat transfers between the gas and tank find the pressure in the tank at the end of the venting process. Tc =304.2K; Pc =73.76 bar; ω=.225 (20) 6. In our discussion of departure functions we derived the following expression for evaluating the internal energy departure function given any equation of state. ( )U U
RTT
ZT
dig
o
−= −
∫ ∂
∂ρρ
ρ
a) Derive the analogous expression for (Cv-Cvig)/R
b) Derive an expression for (Cv-Cvig)/R in terms of a, b, ρ, T for the EOS:
Z bb
a T= ++
− −11
1ρρ
ρ[exp( / ) ]
Answers: 1a) 112 (b) 2220 J/mol (c)12.5bar(d)686K (2)-13900J/mol(3)Cv-S/p[T(dp/dT)-p]
(4) -5.7π (5)20.8bar(6.a) ( −
−
∫ 2 2
2
2TZT
TZ
Td
o
∂∂
∂∂
ρρ
ρ
(b) a2ρT-2 exp(a/T) )
4200:225 Eq. Thermo. Spring 94 TEST 2 NAME_______ 1a. Compute the density (g/cc) of liquid MethylTertiaryButylEther (MTBE) (MW=88) at 1 bar and 300K. Tc =496.4; Pc =33.7 bar; ω =.269(5) 1b. Estimate the vapor pressure (bar) of MTBE at 400K.(5) 1c. When the radial distribution function is equal to unity, how does the coordination number change with respect to the range of the neighborhood around the central atom?. Give an equation with no integral signs in it. (5) 2. Express in terms of in terms of only P, V, T, CP, CV and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂A/∂V)P.(10) 3. Ammonia is continuously compressed from 1 bar and 100°C to 50 bar and 150°C. Compute the enthalpy change per mole of ammonia. Tc =405.6K; Pc =112.8 bar; ω=0.250; CP /R=4.6 (20) 4. Suppose u(r) is given by the 1.5 square-well potential and g(r)=exp(5σ/r) for r>σ. Evaluate the internal energy departure function where ρσ3=1 and ε/kT=1. (15)
5. Vapor Freon 152a is to be adiabatically and reversibly compressed from 1 bar and 248 K to 10 bars in a continuous process. Compute the work required in Joules per mole (20) (Tc =386.7; Pc =45bar; ω=0.256; CP =68 J/mol-K) 6. Suppose an equation of state of the form: Z = 1 + 10 Ybρ*exp(2 Ybρ ) where Y = exp(a/Tr)-1 and a,b are constants Develop an expression for the Helmholtz energy departure function.(20) Answers: 1a0.76g/cc (b) 6.5 bars (c) ρ 4π/3 R3 2. 69J/mol ± 40 J/mol 3. -S(∂T/∂V)P - P 4. 5092 ±400 6.5[exp(2Ybρ)-1] 4200:225 Eq. Thermo. Spring 96 TEST 2 SSN _______ 1.a. Estimate the vapor pressure of propane at 325 K. 1.b. Estimate the saturated liquid density (g/cc) of propane at 325 K. 1.c. What is it about molecules that causes the compressibility factor to be less than unity most of the time? 1.d. Estimate the heat of vaporization (J/mole) of propane at 325 K. 2. Express in terms of P, V, T, Cp, Cv, and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂S/∂T)H.(10) 3. Estimate the change in entropy (J/mole-K) for raising propane from a saturated liquid at 230K to a saturated vapor at 298K.(20) (CP /R = 8.85) 4. Suppose the radial distribution function at intermediate densities can be reasonably represented by: g ~ (1+2(σ/r)2) at all temperatures. Derive an expression for the attractive contribution to the compressibility factor for fluids that can be accurately represented by the Sutherland potential.(15) 5. Suppose we wanted to design a fix-a-flat system based on propane. Let the can be 500 cc and the tire be 40,000 cc. Assume the tire remains isothermal and at low enough pressure for the ideal gas approximation to be applicable. The can is ~ filled with 250 g of saturated liquid propane at 298K. If the pressure in the can drops to 0.85 MPa, what is the pressure in the tire and the amount of propane remaining in the can? Assuming 20 psig is enough to drive the car for a while, is the pressure in the tire sufficient? Could you fill another tire?(20) 6. Even in the days of van der Waals, the second virial coefficient for square-well fluids was known to be: B2/b = 4 + 9.5 [exp(NAε/RT)-1]. Noting that ex ~ 1 + x + x2/2, this observation suggests the following equation of state:
Zb
b
N
RTbA= +
−−1
4
1
9 5ρρ
ερ
.
Derive an expression for the Helmholtz energy departure function for this equation of state. (15) 1)18bar,.44,molecular attraction,12300(2)ugly(3)79(4)3πρσ3ε/kT(5)-4ln(1-bρ)-9.5εbρ/kT 4200:225 Eq. Thermo. Spring 97 TEST 2 SSN _______ 1.a. Estimate the fugacity of saturated liquid n-butane at 390 K. 1.b. Which would you expect to be higher: the density of butane at 426K and 38 bars or the density of butane at 450K and 60 bars? Why? 1.c. Why does the radial distribution function go to zero for r < σ? 1.d. Estimate the heat of vaporization (J/mole) of n-butane at 390 K. 2. n-butane is isothermally compressed from 425K and 1 bar to 100 bars. Estimate the change in enthalpy (J/mole). 3. Estimate the work output (J/mole) for n-butane when it is continuously, adiabatically, and reversibly expanded from a saturated liquid at 390K to 1.5 bars.(20) 4. Suppose the radial distribution function can be reasonably represented by:
++
−−
++=)21(
1)21(
)]1(cos[211 55 xbkTxbxbg
ρε
ρπρ where x ≡ r/σ and cos is evaluated in radians
Derive an expression for the compressibility factor for fluids that can be accurately represented by the Square-Well potential.(20)
5. Based on the work of Lee and Sandler (1986), one might propose the following equation of state:
Zb
b
b
kT
b
b kT= +
−−
++
18
2 4
9 5 1
1 5
ρρ
ε ρ ρρε
.
/
Derive an expression for the Gibbs energy departure function of this equation of state (20).
Hint: )ln(2 baxab
ax
baxxdx
+−=+∫
Answers: 1)15.6bars, 12544, (450,60), 2 in same place (2) -15235 (3) -2804
(4) [ ]
+
+−−
+
+
−
++=)151(
/11)/exp(5.1)21(
/1)21(
2141 3
ρεε
ρε
ρρρ
bkTkT
bkT
bbbZ
(5) G G
RTb b kT b kT Z Z
ig−= − − − + − + + − −2 1 2
9 5
51 5 1 5 1ln( )
.( / ) ln( / ) lnρ ρ ε ρε
4200:225 Eq. Thermo. Spring 98 TEST 2 SSN _______ 1.a. Estimate the density (g/cm3) of saturated liquid carbon dioxide at 290 K. (MW=44) 1.b. An absorption experiment requires a flow rate of 7.5 kg/hr of CO2. A standard cylinder of CO2 contains 48139 cm3of saturated liquid at 290K. A typical run of the experiment takes 2 hours. How many runs can we make on one cylinder? 1.c. Write the energy and entropy balances for the above CO2 cylinder as the experiment proceeds. 1.d. Estimate the heat of vaporization of CO2 at 290K. If 1 kg of CO2 were vaporized, how much heat (kJ) would be required? 2. Express in terms of P, V, T, Cp, Cv, and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂S/∂U)P.(15) 3. A physicist studying superconductivity needs to cool his experiment by continuously passing a stream of nitrogen through a throttle impinging on his apparatus. In your calculations, please take the saturated liquid at 0.003 MPa to be the Reference State. a. If he can maintain the outlet from the throttle at 0.003 MPa, what temperature will he maintain at the throttle outlet? (5) b. Write the energy balance for the throttle. (5) c. If his nitrogen inlet is saturated liquid at 0.1 MPa, what quality is obtained from the throttle at 0.003 MPa? In your calculations, please take the saturated liquid at 0.003 MPa to be the reference state. (15) 4. Suppose the radial distribution function can be reasonably represented by:
++=
2)21(1
xbYgρ
where x ≡ r/σ, Y = [exp(NAε/RT)-1], and b = π NA σ3/6 a. Derive an expression for the internal energy departure function for fluids that can be accurately represented by the Square-Well potential.(15) b. Evaluate the expression at bρ = 0.3 and ε/kT = 0.5 (5) 5. Based on the work of Kihara (1976), the third virial coefficient for the square-well fluid can be written as: B3* = B3/b2 = 10 - 19.5 Y + 30.5 Y2 - 8.5 Y3 Where: Z = 1 + B2* η + B3* η2 Y = [exp(NAε/RT)-1], and b = π NA σ3/6, η = bρ, B2* = 4 - 9.5 Y Derive an expression for the Internal energy departure function of this equation of state(20). 4200:225 Eq. Thermo. Spring 99 TEST 2 SSN _______ 1.a. Estimate the density (g/cm3) of saturated liquid propylene at its normal boiling temperature. (MW=42) (5) Tc = 364.8, Pc = 4.613 MPa, ω = 0.142, A = 3.710, B = 0.2345, C = -1.16E-4, D=2.205E-8
1.b. Compute the heat of vaporization (kJ/kg) of propylene at its normal boiling temperature.(5) 1.c. Write the energy and entropy balances for reversible, isothermal compression of propylene from 1 bar and 298K to 22 bars. (5) 2. Express in terms of P, V, T, Cp, Cv, and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂V/∂T)U.(10) 3. Propylene (NOT propane) is to be used in a vapor compression cycle with turbine expansion operating between 297K at the exit from the condenser and 187K in the evaporator. The heat removal rate from the evaporator is to be 215,000 kJ/hr. The compressor and turbine can be assumed adiabatic and reversible. Compute the Coefficient of Performance of this cycle using propylene.(20) Tc = 364.8, Pc = 4.613 MPa, ω = 0.142, A = 3.710, B = 0.2345, C = -1.16E-4, D=2.205E-8 4. 300 lbs of saturated liquid propylene at 297K initially fill a tank to supply an absorption test apparatus. 15 lbs per hour are used in the experiment. Assuming the supply tank is adiabatic and that only saturated liquid enters the valve and that vapor at 255K and 1 bar exits the valve, what heat rate (kW) is required for the valve? The heat rate required during the first few minutes will be sufficient. (20) 5. Suppose the radial distribution function can be reasonably approximated by:
−−
−
−−
=)1(
)/13(1exp)1(2/12 ρ
ρερρ
bxb
RTN
bbg A
where x ≡ r/σ, ρ is the molar density, and b = π NA σ3/6 a. Referring to the pressure equation, derive an expression for the compressibility factor for fluids that can be accurately represented by the Square-Well potential.(15) b. Evaluate the expression at bρ = 0.333 and ε/kT = 0.5 (5) 6. As part of a new equation of state, one might propose the following equation of state:
[ ]
−−
−+= ρ
εερρρ b
RTN
RTNb
bbZ AA 31exp
5.9)1(
41 2
Derive an expression for the Internal energy departure function of this equation of state (15).
Hint:
−=∫ a
ya
aydyayy 1)exp()exp(
4200:225 CLASSICAL THERMODYNAMICS Spring 00 TEST 2 SSN________ 1. Short Answer a) Estimate the density of mercury (g/cc) at 0.1 MPa and 300 K. (Tc =1735 K, Pc =161 MPa, ω=-0.1644, MW = 201 g/mole) b) Estimate the saturation temperature of mercury at 0.1MPa. (Tc =1735 K, Pc =161 MPa, ω= -0.1644) (Hint: Are there any other questions on this test for which knowing the vapor pressure might be helpful?) c) Estimate the change in entropy (J/mole-K) in going from carbon monoxide at 32 MPa and 197 K to 3.2 MPa and 130 K. 2. Express in terms of P, V, T, Cp, Cv, and their derivatives. Your answer may include absolute values of S if it is not associated with a derivative. (∂V/∂T)G. (10) 3. Saturated vapor mercury is to be adiabatically and reversibly compressed from 0.1 MPa to 10 MPa in a continuous process. Compute the work required in Joules per mole. (20) (Tc =1735 K, Pc =161 MPa, ω=-0.1644, CP/R =2.5)
4. As part of a new equation of state, the following contribution has been proposed:
])(5.15.21[4
12ρρ
ρbb
bZ
+−+=
Derive an expression for the Helmholtz energy departure function of this equation of state (20). 5. A single-stage Rankine cycle for power generation is to operate on mercury as the working fluid. The condenser is to operate at 383°C and the boiler is to operate at 10 MPa. The exit from the adiabatic, reversible turbine is saturated vapor. Estimate the thermodynamic efficiency of this cycle and compare it to the value for the Carnot cycle operating between the same highest and lowest temperatures. (Tc =1735 K, Pc =161 MPa, ω= -0.1644, CP/R =2.5) (15) 6. Suppose the radial distribution function can be reasonably approximated by:
( ) 2)1cos(
2121
xx
bkTbg
−−
+=ρ
ρε
where x ≡ r/σ, cosine function is in radians, ρ is the molar density, and b = π NA σ3/6 a. Referring to the pressure equation, derive an expression for the compressibility factor for fluids that can be accurately represented by the Square-Well potential.(15) b. Evaluate the expression at bρ = 0.34 and ε/kT = 0.5 (5)