EMC TEST REPORT · 2017-06-01 · equipment to the chamber and 3 foot by 7 foot door to the control room. Interconnection cables between the chamber and the control room are through

TESTING CERT #9999.99

Crestron Electronics, Inc. 22 Link Drive Rockleigh, NJ 07647 Tel: 800.237.2041/ 201.767.3400 Fax: 201.767.7576 www.crestron.com

FCC Registration #412871 Industry Canada Site #5683C-1

EMC TEST REPORT

Report Number: TST600-EMS-11022012

Equipment Under Test (EUT):

Product: 5.7” Wireless Touch Panel

Model: TST-600

Report Date: November 2, 2012

Standards: FCC Part 15 Class B EN55022 and CISPR 22 Class B

Test Result: PASS

Prepared by:

Date: Nov. 2, 2012

Hirayr M. Kudyan, Sr. Compliance Engineer Reviewed by:

Date: Dec. 11, 2012

Dan Roman, Global Compliance Manager

Report Number: TST600-EMS-11022012 Page 2 of 19

Table of Contents

1. GENERAL DESCRIPTION ................................................................................................ 3

1.1 PRODUCT DESCRIPTION ................................................................................................... 3 1.2 TEST METHODOLOGY ...................................................................................................... 3 1.3 TEST FACILITY ................................................................................................................. 3

2. SYSTEM TEST CONFIGURATION ................................................................................. 5

2.1 BLOCK DIAGRAM ............................................................................................................. 5 2.2 EUT TEST SETUP JUSTIFICATION ..................................................................................... 5 2.3 EUT EXERCISE SOFTWARE AND MODE(S) OF OPERATION ............................................... 5 2.4 CABLES ............................................................................................................................ 6 2.5 SPECIAL ACCESSORIES ..................................................................................................... 6 2.6 SUPPORT EQUIPMENT ....................................................................................................... 6 2.7 EUT CLOCKS ................................................................................................................... 7 2.8 EQUIPMENT MODIFICATIONS ........................................................................................... 7 2.9 AMBIENT TEST CONDITIONS ............................................................................................ 7

3. TEST RESULTS ................................................................................................................... 8

3.1 TEST SUMMARY ............................................................................................................... 8 3.2 TEST DATA ...................................................................................................................... 9 3.4 TEST EQUIPMENT ........................................................................................................... 15 3.5 CONFIGURATION PHOTOGRAPHS .................................................................................... 16

This document shall not be reproduced, except in full, without written approval from Crestron Electronics, Inc. Revision History Revision Description Date 00 Initial release 11-Dec-2012


1. General Description

1.1 Product Description The equipment under test (EUT) is a 5.7” Wireless Touch Panel, model: , manufactured by Crestron Electronics, Inc. Model Number: TST-600 Serial Number: X120339 Power Rating: 24VDC at 0.75 A, supplied by AC adaptor

1.2 Test Methodology Conducted and radiated emission measurements were performed according to the procedures in ANSI C63.4: 2003 and CISPR 22: 2005. All measurements were performed in a semi-anechoic chamber. For each scan, the procedures for maximizing emissions were followed. All radiated measurements were performed at 3 meters distance between an antenna and the EUT, unless stated otherwise in this report.

1.3 Test Facility The 3-meter semi-anechoic chamber used to collect conducted and radiated emission data is located at 22 Link Drive, Rockleigh, New Jersey. This test facility has been placed on file with the FCC, Registration Number: 412871, and Industry Canada, Site Number 5683C-1. The interior shield-to-shield dimensions of the chamber are 28 feet long by 20 feet wide by 20 feet high with an 18 inch raised floor. The test facility includes a shielded control room with interior shield-to-shield dimensions of 16 feet long by 10 feet wide by 8 feet high.

The RF shielded enclosures of the chamber and the control room consist of modular panels of galvanized steel with steel framing. There are seven power filters to supply power to the chamber and two power filters to supply power to the control room. Lighting consisting of six floodlight fixtures in the chamber and two in the control room are powered through a separate power filter. HVAC is provided by four honeycomb wave-guide air vents mounted in the chamber’s ceiling, two in the control room. A 4 foot by 7 foot brass knife single leaf swing door is provided for the access of personnel and equipment to the chamber and 3 foot by 7 foot door to the control room. Interconnection cables between the chamber and the control room are through two 6 inch by 24 inch RF tunnels, one 1-1/2 inch pipe penetration, and one 4 inch pipe penetration. The RF shielded enclosures meet RF shielding effectiveness of 106 dB at 10 GHz.


The chamber is treated with hybrid absorbers to achieve the requirements of ANSI C63.4:2003 and CISPR 16-1-4:2008 at a 3 meter distance. Four side walls and the ceiling of the chamber are covered with ferrite tiles. Specula regions (the end wall behind the turntable, a 10 foot by 10 foot area of the ceiling, and a 10 foot by 10 foot area on each side wall) are covered with foam absorbers. Sixteen pieces of removable PS-600 hybrid absorbers (includes FT-1500 and PAA-600) on eight floor carts for immunity are stored inside the chamber, along walls, during emission and volumetric normalized site attenuation measurements. The turntable is a motor driven 2 meter diameter metal turntable. There are three sets of flush mount receptacles on the turntable to provide 120V, 230V, and 277V power to equipment under test. Interconnecting cables between the EUT and support equipment may be routed through the turntable’s center opening. An antenna mast is used for moving antennas up and down and for changing antenna polarizations. A position controller located in the control room controls the rotation of the turntable and the height and polarization of the antenna. Controlling cables are through a fiber optic converter and ST couplers to the control room. The test volume of the 3 meter test range is a cylinder two meters in diameter. NSA measurement is in accordance with Section 5.4.6.5 of ANSI C63.4-2003 and Clause 5.7.1 of CISPR 16-1-4 Edition 2.1. Conducted emissions are performed in the 3 meter chamber. A 2 meter by 2 meter vertical coupling plane is placed 40 centimeters behind the table that supports desktop equipment under test. LISNs are placed on top of the turntable (reference ground plane) and bonded to the turntable of the chamber. The EUT is connected to one LISN. All other equipment is powered from an additional LISN. Unused LISN measuring port connectors are terminated in 50 ohms. Each phase of the power line is measured separately. For radiated and line conducted emission measurements, a 1.5 meter long by 1 meter wide by 0.8 meter high table is placed on top of the turntable to support tabletop equipment. The table frame is made of 1-1/2 inch PVC pipes. The tabletop is made of ¼ inch polycarbonate.


2. System Test Configuration

2.1 Block Diagram Two configurations were tested, as follows: Configuration 1 TST-600 off-dock, running on internal battery power. Configuration 2 TST-600 mounted on dock, powered by IMCW (see Figure below)

PWR

AC

LAN

UUT

DOCK

IMCW

BACK FRONTEXTERNALETHERNET

SWITCH

FAIR-RITE0431164281

CLAMPFAIR-RITE

2631102002CORE

3-TURNSIN DOCKPWR

24VDC .75A

2.2 EUT Test Setup Justification The system was configured for testing in two representative user configurations with nominal interface data activity and typical loading.

2.3 EUT Exercise Software and Mode(s) of Operation

Firmware revision: v1.006.0000 (Oct 01 2012 Software revision: 1.0.4624.3503 Application program: N/A


Step-by-step Operating Instructions: Battery-Only Operation Turn UUT on by flipping a recessed switch, located on the back, up. Unit is ready when “H” pattern appears. On-Dock Operation Connect LAN cable to IMCW at jack labeled “LAN”. Plug 24V supply into jack labeled “PWR 24VDC .75A” Connect dock cable into jack located on front of the IMCW. Turn UUT on by flipping a recessed switch, located on the back, up.

Place UUT on dock (green light at pin-hole on upper right front of UUT will start flashing). After booting, an “H” pattern will be displayed.

2.4 Cables

Qty Description Length (m) From - To Type Shielded/ Unshielded

1 CAT5E 12 IMCW to FO switch CAT5e Unshielded

2.5 Special Accessories There are no special accessories for compliance of this EUT.

2.6 Support equipment

No Description Manufacturer Model No Serial No

1 Dock Crestron TPS-6X-DS-LP-B-T 7596696

1 Interface module Crestron TST-600-IMCW n/a 1 24V Power supply Crestron PW-2407WU n/a


2.7 EUT Clocks 24MHz, 50MHz, 400MHz, 800MHz. The upper frequency limit of required emissions testing is 5GHz, based on the 800MHz clock.

2.8 Equipment Modifications There were no modifications made during compliance measurements.

2.9 Ambient Test Conditions During testing contained in this test report, average ambient test conditions were as follows: Relative humidity between 30-70%, temperature 20-24°C, and barometric pressure between 990-1100 mb.


3. Test Results

3.1 Test Summary

Test Standard Specifications *

Date of Test (mm/dd/yy) Test Engineer

Test Result (P or F) Config 1 Config 2

FCC 15B

Conducted Class B

0.15-0.5MHz, 66-56QP, 56-46AVdBµV 0.5-5MHz, 56QP, 46AV dBµV 5-30MHz, 60QP, 50AV dBµV

N/A 10/03/12 Hirayr Kudyan Pass

Radiated Class B (3m)

30-88MHz, 40 dBµV/m 88-216MHz, 43.5 dBµV/m 216-960MHz, 46 dBµV/m Above 960MHz 54 dBµV/m 1GHz – 5GHz, 54AV, 74PK dBµV/m

10/03/12, 10/04/12

10/03/12, 10/04/12

Hirayr Kudyan Pass

CISPR 22: 2005 EN 55022: 2006

Conducted Class B

0.15-0.5MHz, 66-56QP, 56-46AV dB(µV) 0.5-5MHz, 56QP, 46AV dBµV 5-30MHz, 60QP, 50AV dBµV

N/A 10/03/12 Hirayr Kudyan Pass

Radiated Class B (3m)

30-230MHz, 40.5 dBµV/m 230MHz-1GHz, 47.5 dBµV/m 1-3GHz, 50 AV 70 PK dBµV/m 3-5GHz, 54 AV 74 PK dBµV/m

10/03/12, 10/04/12

10/03/12, 10/04/12

Hirayr Kudyan Pass

*Unless otherwise indicated, all levels are in QP

Test results relate only to the item(s) tested. The final test results represent the worst case.


3.2 Test Data 3.2.1 Conducted Emission Test Data Configuration 1 (Not Applicable) Configuration 2

120VAC, Line 1

120VAC, Line 2

150 kHz 30 MHz

1 PK

6DB

TD SCAN

dBµV dBµV

TDF

MAXH

MT 100 µsRBW 9 kHz

PREAMP OFFAtt 10 dB

DC

1 MHz 10 MHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 52.30 dBµV 179.250000000 kHz

2

Marker 2 [T1 ] 45.13 dBµV 235.500000000 kHz

3

Marker 3 [T1 ] 37.42 dBµV 307.500000000 kHz

4

Marker 4 [T1 ] 36.86 dBµV 327.750000000 kHz

AVE

QP

Date: 3.OCT.2012 17:37:37

TDF

TD SCAN

150 kHz 30 MHz

dBµV dBµV

1 PKMAXH

6DB

RBW 9 kHzMT 100 µsPREAMP OFFAtt 10 dB

DC

1 MHz 10 MHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 50.52 dBµV 177.000000000 kHz

2

Marker 2 [T1 ] 43.55 dBµV 235.500000000 kHz

3

Marker 3 [T1 ] 37.86 dBµV 298.500000000 kHz

4

Marker 4 [T1 ] 37.29 dBµV 350.250000000 kHz

AVE

QP

Date: 3.OCT.2012 17:48:40


230VAC, Line 1

230VAC, Line 2

TDF

TD SCAN

150 kHz 30 MHz

dBµV dBµV

1 PKMAXH

6DB


DC

1 MHz 10 MHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 51.08 dBµV 174.750000000 kHz

2

Marker 2 [T1 ] 50.49 dBµV 192.750000000 kHz

3

Marker 3 [T1 ] 45.90 dBµV 233.250000000 kHz

4

Marker 4 [T1 ] 46.28 dBµV 246.750000000 kHz

AVE

QP

Date: 3.OCT.2012 18:09:24

TDF

TD SCAN

150 kHz 30 MHz

dBµV dBµV

1 PKMAXH

6DB


DC

1 MHz 10 MHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 48.09 dBµV 177.000000000 kHz

2

Marker 2 [T1 ] 47.55 dBµV 186.000000000 kHz

3

Marker 3 [T1 ] 44.34 dBµV 235.500000000 kHz

4

Marker 4 [T1 ] 43.08 dBµV 251.250000000 kHz

AVE

QP

Date: 3.OCT.2012 17:59:09


FCC15 / CISPR22 Class B Frequency

(MHz) Measured Level (dBuV) Limits (dBuV) Margins

(dB) QP AV QP AV QP AV

120V/L1 0.17925 45.9 34.39 64.53 54.53 18.63 20.14 0.2355 42.29 28.88 62.26 52.26 19.97 23.38 0.3075 32.94 22.74 60.04 50.04 27.10 27.30 0.32775 29.61 18.18 59.52 49.52 29.91 31.34 0.37275 37.84 27.36 58.45 48.45 20.61 21.09 0.4065 38.94 25.01 57.73 47.73 18.79 22.72

120V/L2

0.177 47.28 33.15 64.63 54.63 17.35 21.48 0.2355 40.5 26.45 62.26 52.26 21.76 25.81 0.2985 33.17 22.68 60.29 50.29 27.12 27.61 0.35025 33.65 21.72 58.96 48.96 25.31 27.24 0.37725 33.43 23.72 58.35 48.35 24.92 24.63 0.4245 35.52 25.04 57.37 47.37 21.85 22.33

230V/L2

0.177 45.44 32.38 64.63 54.63 19.19 22.25 0.186 42.72 33.6 64.22 54.22 21.50 20.62 0.2355 40.62 28.73 62.26 52.26 21.64 23.53 0.25125 39.54 28.84 61.72 51.72 22.18 22.88 0.3885 37.37 23.3 58.10 48.10 20.73 24.80 0.411 36.85 25.6 57.64 47.64 20.79 22.04

230V/L1

0.17475 47.46 32.6 64.74 54.74 17.28 22.14 0.19275 47.16 32.62 63.92 53.92 16.76 21.30 0.23325 43.1 29.36 62.34 52.34 19.24 22.98 0.24675 42.3 32.18 61.87 51.87 19.57 19.69 0.3885 40.69 26.33 58.10 48.10 17.41 21.77 0.411 40.64 28.41 57.64 47.64 17.00 19.23

Tested by Hirayr Kudyan, 10/03/2012


3.2.2 Radiated Emission Test Data Configuration 1

Vertical, 100cm

Horizontal, 100cm

TD SCAN

30 MHz 1 GHz

dBµV dBµV

1 PK

TDS

MAXH

6DB

RBW 120 kHzMT 100 µsPREAMP ONAtt 0 dB

AC

100 MHz 1 GHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 25.63 dBµV 225.000000000 MHz

2

Marker 2 [T1 ] 27.59 dBµV 275.010000000 MHz

3

Marker 3 [T1 ] 31.25 dBµV 399.990000000 MHz

4

Marker 4 [T1 ] 33.46 dBµV 603.780000000 MHz

C22BFCCB

Date: 4.OCT.2012 12:40:04

TD SCAN

30 MHz 1 GHz

dBµV dBµV

1 PK

TDS

MAXH

6DB


AC

100 MHz 1 GHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 31.65 dBµV 225.030000000 MHz

2

Marker 2 [T1 ] 38.27 dBµV 275.010000000 MHz

3

Marker 3 [T1 ] 33.20 dBµV 376.590000000 MHz

4

Marker 4 [T1 ] 32.34 dBµV 672.780000000 MHz

C22BFCCB

Date: 4.OCT.2012 12:46:00


Antenna Turntable Azimuth

Angle (degrees)

Frequency (MHz)

Measured Level

(dBuV/m) (QP)

FCC Class B

CISPR22 Class B

Orientation

Height (cm)

Limit (dBuV/m)

Margin (dB)

Limit (dBuV/m)

Margin (dB)

H 144 1 225 30.55 46 15.45 40.5 9.95

H 133 360 275 37.01 46 8.99 47.5 10.49

V 149 180 375 25.51 46 20.49 47.5 21.99

V 161 22 400 30.58 46 15.42 47.5 16.92

V 94 290 437.49 31.77 46 14.23 47.5 15.73

V 123 359 602.34 25.89 46 20.11 47.5 21.61

V 128 205 750 30.16 46 15.84 47.5 17.34

Tested by: Hirayr Kudyan Date(s): 10/04/2012 No emissions over 1 GHz were within 6 dB of the limits.

Configuration 2 Vertical, 100cm

Horizontal, 100cm

TD SCAN

30 MHz 1 GHz

dBµV dBµV

1 PK

TDS

MAXH

6DB


AC

100 MHz 1 GHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 35.81 dBµV 50.430000000 MHz

2

Marker 2 [T1 ] 32.89 dBµV 94.350000000 MHz

3

Marker 3 [T1 ] 33.08 dBµV 101.880000000 MHz

4

Marker 4 [T1 ] 33.33 dBµV 375.000000000 MHz

C22BFCCB

Date: 4.OCT.2012 16:52:44


Antenna Turntable Azimuth

Angle (degrees)

Frequency (MHz)

Measured Level

(dBuV/m) (QP)

FCC Class B

CISPR22 Class B

Orientation

Height (cm)

Limit (dBuV/m)

Margin (dB)

Limit (dBuV/m)

Margin (dB)

V 89 232 47.79 31.81 40 8.19 40.5 8.69

V 109 247 94.35 30.38 40 9.62 40.5 10.12

V 101 229 108.81 29.7 40 10.3 40.5 10.8

V 108 291 125 29.57 43.5 13.93 40.5 10.93

H 126 214 225 32.24 46 13.76 40.5 8.26

H 106 221 275 29.58 46 16.42 47.5 17.92

H 93 231 325 33.73 46 12.27 47.5 13.77

H 108 253 375 27.48 46 18.52 47.5 20.02

V 121 117 687.48 33.92 46 12.08 47.5 13.58

Tested by: Hirayr Kudyan Date(s): 10/04/2012

No emissions over 1 GHz were within 6 dB of the limits.

TD SCAN

30 MHz 1 GHz

dBµV dBµV

1 PK

TDS

MAXH

6DB


AC

100 MHz 1 GHz

0

10

20

30

40

50

60

70

80

90

100

1

Marker 1 [T1 ] 26.95 dBµV 125.040000000 MHz

2

Marker 2 [T1 ] 33.52 dBµV 324.990000000 MHz

3

Marker 3 [T1 ] 32.80 dBµV 225.000000000 MHz

4

Marker 4 [T1 ] 34.65 dBµV 375.000000000 MHz

C22BFCCB

Date: 4.OCT.2012 16:48:52


3.4 Test Equipment

Item Equipment Type Manufacturer Model No. Serial No. Cal. Due

1 EMI Receiver Rohde & Schwarz ESU40 100076 Dec. 21, 2012

2 Antenna Teseq CBL 6112D 25231 Dec. 9, 2012

3 Antenna ETS-Lindgren 3117 00047560 Feb. 23, 2013

4 Preamplifier Rohde & Schwarz TS-PR18 100044 Nov. 29, 2012

5 LISN Solar Electronics 9252-50-R-24-N 068545 Mar. 5, 2013

!Undefined Bookmark,

ITEM8 Hi-pass filter Solar 7801-120 1110701 Dec. 28, 2012

All instruments are calibrated in accordance with the manufacturer’s recommendations. All antennas are calibrated per ANSI C63.5 and traceable to national standards.


3.5 Configuration Photographs 3.5.1 Conducted Emission Configuration Photographs Configuration 1 (N/A) Configuration 2

Worst-case conducted emission, front view


Worst-case conducted emission, side view


3.5.2 Radiated Emission Configuration Photographs Configuration 1

Worst-case radiated emission, front view

Worst-case radiated emission, rear view


Configuration 2

Worst-case radiated emission, front view

Worst-case radiated emission, rear view

Documents

EMC TEST REPORT · 2017-06-01 · equipment to the chamber and 3 foot by 7 foot door to the control room. Interconnection cables between the chamber and the control room are through