Upload
betty-gutierrez
View
223
Download
0
Embed Size (px)
Citation preview
7/29/2019 ES832 Lect4 Fuel
1/38
ENERGY CONVERSIONES 832a
Eric Savorywww.eng.uwo.ca/people/esavory/es832.htm
Lecture 4 Fuels
Department of Mechanical and Material EngineeringUniversity of Western Ontario
7/29/2019 ES832 Lect4 Fuel
2/38
Aim: To examine the different fuel sources
These include:
Fossil fuels
- Coal- Fuel oil- Natural gas- Bitumen
Synthetic fuel
7/29/2019 ES832 Lect4 Fuel
3/38
Fossil fuels Four main types: Coal, fuel oil, natural gas and bitumen
Fossil Fuels are hydrocarbons, formed from the remainsof dead plants and animals. Fossil fuel is a general termfor buried combustible geological deposits of organicmaterials, formed from decayed plants and animals thathave been converted to crude oil, coal, natural gas or
heavy oils by exposure to heat and pressure in theearth's crust over hundreds of millions of years.
The chemical compound is Cx(H20)y, which is producedby plants through photosynthesis where solar energy is
converted to chemical energy. Most of the fossil fuels were produced in the
Carboniferous Period of the Paleozoic Era: 299 - 359million years ago.
The fuel formulation is: CnH2n+2.
7/29/2019 ES832 Lect4 Fuel
4/38
Fossil fuels
Coal - it is composed primarily of carbon
along with assorted other elements, includingsulphur.
Fuel oil - it is made of long hydrocarbon
chains, particularly alkanes, cycloalkanes andaromatics.
Natural gas - consisting primarily of methane(CH4) but including significant quantities of
ethane (C2H6), propane (C3H8), butane (C4H10),carbon dioxide, nitrogen, helium andhydrogen sulphide. It is found in oil fields,
natural gas fields and in coal beds.
7/29/2019 ES832 Lect4 Fuel
5/38
Bitumen it is a mixture of organic liquids that
are highly viscous, black, sticky, entirely solublein carbon disulphide (CS2), and composedprimarily of highly condensed polycyclic aromatichydrocarbons (PAHs).
Bitumen is primarily used for paving roads.Its other uses are for general waterproofingproducts, including the its use in the
production of roofing felt.
Oil shale - is a general term applied to a groupof rocks rich enough in organic material (called
kerogen) to yield petroleum upon distillation.
Fossil fuels
7/29/2019 ES832 Lect4 Fuel
6/38
Coal Coal is formed from plant remains that have been
compacted, hardened, chemically altered, and
metamorphosed by heat and pressure overgeological time.
Coal was formed in swamp ecosystems which
persisted in lowland sedimentary basins. Theseswamp environments were formed during slowsubsidence of passive continental margins, andmost seem to have formed adjacent to estuarine and
marine sediments. When plants die in these peat swamp environments,
their biomass is deposited in anaerobic aquaticenvironments where low oxygen levels prevent their
complete decay by bacteria and oxidation.
7/29/2019 ES832 Lect4 Fuel
7/38
Burial by sedimentary loading on top of the peatswamp converts organic matter to coal by:
- Compaction, due to loading of the sediments on the
coal which flattens the organic matter- Removal of water held within the peat in between theplant fragments- Ongoing compaction removal of water from the inter-
cellular structure of fossilized plants- Heat and compaction removal of water- Methanogenesis; similar to treating wood in a pressurecooker, methane is produced, which removes hydrogenand some carbon, and some further oxygen (as water)
- Dehydrogenation, which removes hydroxyl groups(OH) from the cellulose and other plant molecules,resulting in the production of hydrogen-reduced coals
Generally, to form a coal seam 1m thick, some 10 - 30m of
peat is required. Peat has a moisture content of up to 90%.
7/29/2019 ES832 Lect4 Fuel
8/38
Coal formation
7/29/2019 ES832 Lect4 Fuel
9/38
Coal mining The most economical method of coal extraction from coal
seams depends on the depth and quality of the seams,
and also the geology and environmental factors of thearea being mined. Surface and mountain top mining
If the coal seams are near the surface, the coal is extracted by
strip mining. Strip mining exposes the coal by the advancement ofan open pit or strip.
Mountain top removal is a form of surface mining that takes placeat the topmost portion of a mountain. Utilized for the past 30years, mountain top mining involves removing the highest part ofthe mountain for the maximum recovery of coal.
Underground mining
Most coal seams are too deep underground for open cast miningand thus this type of mining is called underground mining. In deepmining, the room and pillar method progresses along the
Mammoth coal veinseam, while pillars and timber are left standingto support the coal mine roof.
7/29/2019 ES832 Lect4 Fuel
10/38
Petroleum (oil, gas)Petroleum forms from the remains of plants and animalsthat lived in the ocean 10-160 million years ago.
When organisms died and sank to the bottom, they werecovered in mud, sand, and other mineral deposits. Thisrapid burial prevented immediate decay, which would
normally occur if the organisms remained exposed on thesea floor.
The lack of oxygen in the sedimentary layers causedorganisms to slowly decay into carbon-rich compounds.
These compounds mixed with surrounding sediments andformed source rock, which is a type of fine-grained shale.
As more layers were deposited on top of one another,pressure and heat acting on the source rock compressed
the organic material into crude oil.
7/29/2019 ES832 Lect4 Fuel
11/38
Discovering the location of oil within the earth is difficultbecause of the presence of cap rock, which can be miles
thick in some locations. Oil geologists study surfacerocks and the terrain to determine if any oil is presentunderground, but the best evidence comes from varioussatellite imaging techniques.
Oil flows may disrupt the earth's gravitational ormagnetic field and so gravity meters and magnetometerscan detect some oil sources.
The most reliable method for finding oil is through the
use of shock waves in a process called seismology.
In a seismological survey a shock wave is aimed at the surface of thewater or land and the length of time it takes for the waves to reflectback to the sensor is recorded. The speed of the shock wavedepends on the type of rock it travels through, and by comparing the
travel times to known densities of rock, seismologists can determinewhat rocks are underground and predict if they might contain oil.
Petroleum finding oil
7/29/2019 ES832 Lect4 Fuel
12/38
The most common method of obtainingpetroleum is extracting it from oil wells found in
oil fields. Primary recovery methods are used to extract
oil that is brought to the surface byunderground pressure and can generally
recover about 20% of the oil present. After the oil pressure has depleted to the point
that the oil is no longer brought to the surface,secondary recovery methods draw another 5 to
10% of the oil in the well to the surface. Finally, when secondary oil recovery methods
are no longer viable, tertiary recovery methodsreduce the viscosity of the oil in order to bringmore to the surface.
Petroleum production
7/29/2019 ES832 Lect4 Fuel
13/38
Crude oilrefinement
fractional
distillation
7/29/2019 ES832 Lect4 Fuel
14/38
Oil shale fine grained sedimentary rockcontaining kerogen
The kerogen in oil shale can be converted to oil by the
chemical process of pyrolysis, during which the oilshale is heated to 445 - 500C in the absence of air(=pyrolysis) and the kerogen is converted to oil andseparated out, a process called "retorting".
Oil shale has been burnt directly as a low-grade fuel. It was estimated that in earths crust there are 6.5x1015
Tons of oil shale, about 1,000 times more than coal.
The US Energy Information Administration estimates the
world supply of oil shale at 2.6 trillion barrels ofrecoverable oil, 1.0-1.2 trillion barrels of which are in theUS. However, attempts to develop these reserves havebeen going on for over 100 years with limited success.
The caloric value of oil shale is 100 times smaller than
coal.
7/29/2019 ES832 Lect4 Fuel
15/38
Crude oil production from oil shale
7/29/2019 ES832 Lect4 Fuel
16/38
Energy overview
7/29/2019 ES832 Lect4 Fuel
17/38
7/29/2019 ES832 Lect4 Fuel
18/38
Crude oil and natural gas field counts, cumulativeproduction, proven reserves, and ultimate recovery
7/29/2019 ES832 Lect4 Fuel
19/38
US Coal Demonstrated Reserve Base (as at 1 January 2005)
Energy Information Administration / Annual Energy Review 2005
7/29/2019 ES832 Lect4 Fuel
20/38
US Uranium Reserves and Resources
Energy Information Administration / Annual Energy Review 2005
W ld P i E P d ti b R i d C t
7/29/2019 ES832 Lect4 Fuel
21/38
World Primary Energy Production by Region and Country
Energy Information Administration/Annual Energy Review 2005
7/29/2019 ES832 Lect4 Fuel
22/38
World Crude Oil and Natural Gas Reserves (as at 1 Jan 2005)
DOE-EIA /AnnualEnergy Review 2005
W ld C d Oil P d ti
7/29/2019 ES832 Lect4 Fuel
23/38
World Crude Oil Production
DOE-EIA / Annual Energy Review 2005
7/29/2019 ES832 Lect4 Fuel
24/38
Retail Motor Gasoline Prices in Selected Countries 2005
7/29/2019 ES832 Lect4 Fuel
25/38
Retail Motor Gasoline Prices in Selected Countries, 2005
DOE-EIA/Annual Energy Review 2005
W ld P l C i
7/29/2019 ES832 Lect4 Fuel
26/38
World Petroleum Consumption
DOE-EIA / Annual Energy Review 2005
W ld D N l G C i
7/29/2019 ES832 Lect4 Fuel
27/38
World Dry Natural Gas Consumption
DOE-EIA / Annual Energy Review 2005
7/29/2019 ES832 Lect4 Fuel
28/38
Synthetic Fuels
7/29/2019 ES832 Lect4 Fuel
29/38
Introduction
Synthetic fuel or synfuel is any liquid fuel
obtained from coal, natural gas, or biomass. Itcan sometimes refer to fuels derived from othersolids such as oil shale, tar sand, wasteplastics, or from the fermentation of biomatter.
It can also refer to gaseous fuels produced in asimilar way.
The process of producing synfuels is oftenreferred to as Coal-To-Liquids (CTL), Gas-To-Liquids (GTL) or Biomass-To-Liquids (BTL),depending on the initial feedstock.
7/29/2019 ES832 Lect4 Fuel
30/38
Motivation Synthetic fuels require a relatively high price of crude
oil in order to be competitive with petroleum-based
fuels without subsidies. However, they offer thepotential to supplement or replace petroleum-basedfuels if oil prices continue to rise. Several factors makesynthetic fuels attractive relative to competing
technologies such as biofuels, ethanol / methanol orhydrogen:
The raw material (coal) is available in quantitiessufficient to meet current demand for centuries
It can produce gasoline, diesel or kerosene directlywithout the need for additional steps such asreforming or cracking
There is no need to convert vehicle engines to use adifferent fuel
There is no need to build a new distribution network
7/29/2019 ES832 Lect4 Fuel
31/38
Substitute Natural Gas (SNG)
Infrastructure of gas supply near coal mining. The obtained gas is often Methane; CH4 which
has a caloric value of ~ 1,000 Btu/scf.
Gasification is a process that converts
carbonaceous materials, such as coal,petroleum, or biomass, into carbon monoxideand hydrogen.
Produces High Btu Gas (1,000) & Low Btu Gas(500).
The gas tends to be cheaper than coal.
The gas production technology is simple.
7/29/2019 ES832 Lect4 Fuel
32/38
Gasification processes using coal
1. COAL + H2 CH4 + C + (heat)
2. COAL + 2H2 CH4 + (heat)
3. COAL + H2O CO + H2 + (-heat)
4. 4C + O2 CO2 + heat
5. 2C + O2 2CO2 + heat
H20
O2 (AIR)
7/29/2019 ES832 Lect4 Fuel
33/38
Upgrading
CH4, CO, H2 Raw Gas (500 Btu/scf) CO2, H2S, NH3 Residual
1. CO + H2O CO2 + H22. CO2 + H2, H2S Acid gases removal
3. CO + 3H2 CH4 + H2O Catalytic methanation
Pipe line gas 1000 Btu/scf
7/29/2019 ES832 Lect4 Fuel
34/38
Technological parameters
Type of coal being used
Preparation
Feeding technique to the reactor
Reactor type
Fixed bed
Fluidized bed
Entrained flow Heat supply - external / internal
Temperature and pressure
7/29/2019 ES832 Lect4 Fuel
35/38
Fischer-Tropsch process
Oil gasification is a catalyzed chemicalreaction in which carbon monoxide andhydrogen are converted into liquidhydrocarbons of various forms. Typicalcatalysts used are based on iron and cobalt.The principal purpose of this process is toproduce a synthetic petroleum substitute for
use as synthetic lubrication oil or as syntheticfuel.
I di t th d
7/29/2019 ES832 Lect4 Fuel
36/38
In-direct method
Following the gasification process, by usingH
2and CO, these reactions can occur:
(2m+1)H2+ mCO CmH2m+2 + mH2O
(n+1)H2+ 2mCO CmH2m+2 + nCO2
CmH2m+2is fuel C8H18
Direct method
Coal dissolving and by adding H2 (at temp. of~5000C):
nC + (n+1)H2 C
nH2
n+2
7/29/2019 ES832 Lect4 Fuel
37/38
7/29/2019 ES832 Lect4 Fuel
38/38
Contamination
CO unburned fuel
Hydrocarbons unburned fuel
NOx, N2OS, NO2 reaction at high temp.
SO2 after oxidation, once in contact withwater turns to H2SO4
More information on these processes canbe found at SASOL Technology
www.sasol.com
http://www.sasol.com/http://www.sasol.com/