F20/F30 Ferra Series Hydraulic Pumps

HYDRAULIC SYSTEMS DIVISION Outstanding Hydraulic Products, Service and Expertise, Worldwide

F20/F30 Ferra Series Hydraulic Pumps

HALEX-F20/F30 PMP-USA-2009-12

Reliable, efficient, serviceabledesignHaldex external spur gear, positivedisplacement pumps are offered insingle, double, triple and thru-driveversions.

Single and thru-drive pumps are of athree-section modular design. Frontand rear covers are cast iron for reliability, strength, and sound reduction. A cast iron center section allows gear tips to generatetheir own run-in paths, creating minimum radial gear-tip clearancefor high volumetric efficiency.

The thru-drive pump is a singlepump with a mounting pad and coupling spline in its rear cover,allowing a second pump to bemounted and driven in tandem.

The double pump consists of twosingle pumps, each having its ownoutlet port but sharing a commoninlet port and input shaft. This compact unit can, therefore, servetwo separate hydraulic circuits, orsupply greater volume to a single circuit through the combined deliveryof both pumps.

Besides offering greater design flexibility to hydraulic system designers, thru-drive and doublepumps reduce installation costs sincethey allow multiple pump operationfrom a single mounting and drivepoint. Also, double pumps requireonly one inlet line, compared to thetwo required when separate pumpsare used.

Convenient, economical port-ing arrangementsA large selection of port sizes and positions allows greater systemdesign flexibility, provides the meansfor reducing costs through simplifiedplumbing arrangements, and facilitates the interchangeability ofHaldex and competitive pumps. SAE4-bolt split flange ports and SAEstraight thread ports are standard.

Choice of shafts, rotation and couplingsSplined SAE side-fit drive shafts arestandard. Other popular shafts are available. Pumps are assembled foreither clockwise or counterclockwiserotation.

Thru-drive pumps are provided with output drive couplings that matewith splined SAE side-fit drive shafts.

Meets many mounting requirementsSAE standard wet flange mountingsand single or double shaft seals areavailable on all pumps. Mountingpads meet SAE standards and areavailable in several sizes and types tosatisfy various mounting require-ments and to facilitate interchange-ability of Vickers and competitiveunits.

Double shaft seals are ideal for applications where the pump pilotand shaft extend into a transmissioncase or crankcase. If either seal fails,the pump fluid remains separatedfrom the transmission or crankcasefluid. Leakage past either sealsdrains to the exterior of the pump.

The double seal feature thus reducessystem downtime by preventing themixing of different fluids and providing for visual detection of seal malfunction.

The inlet of the thru-drive pump isopen to the pump’s rear couplingarea, requiring that mating pumpshave a wet-flange mounting. If therear mounting pad is capped insteadof used to mount a pump, it must besealed to prevent fluid leakage andentrance of air.

Heavy duty constructionThe drive gear and drive shaft areone piece construction, as are thedriven gear and shaft, to eliminatethe potential problems of frettingand stress fatigue associated withtwo-piece construction. The one-piece design also allows the use oflarge diameter journals and bearingsfor greater load-carrying capacity.

Gears are of AISI 8620 alloy steel forgreater shaft strength and a strongergear assembly. Gears have ten teethto minimize pressure ripple, andgear sides and shaft journals are carburized, hardened, and ground toa fine finish.

The pumps large teflon impregnatedbronze bearings are installed in precision bored covers for optimumshaft alignment. They provide alarge support area that keeps bearing pressures low enough tohandle most indirect drives. Forapplications imposing very high sideloads, consult your Haldex representative.

NOTE: This catalog features our most standard single, double and triple pump capabilities. Other pump options and multiple pump combinations areavailable. Please contact factory or your Haldex representative for information. See bottom of page 45 for contact information.

DESCRIPTION, FEATURES AND BENEFITS2

Pictures on front cover are used with the kind permission of eg: Atlet, BT, Huddig, Scania, Toro and Volvo Construction Equipment.


LONG-LIFE BEARING SYSTEM

Minimum leakage and wearHaldex pumps utilize two seal packs andtwo wear plates to minimize leakageacross the end faces of the gears and toreduce wear. During startup, the sealpacks mechanically preload and seal acantilever section of the plates againstthe ends of the gears.

The seal packs also establish the wearplate area exposed to system pressure,allowing axial pressure loading and balancing of the cantilever sections. Aspressure increases, the sections deflect toward the gear faces to reduce clearances and balance opposing axial

forces. Running clearances are maintained small enough for mimimumleakage across the faces, yet largeenough to maintain the oil film requiredto minimize wear of mating surfaces.

Radial imbalance(hydraulic load).

Fixed end(minimumdeflection).

Shaftdeflection(exaggerated).

Fixed end(minimumdeflection).

Tapered crosssection.

Pressure port.

Adjustment for deflection

Bearings and support structures movein unison with, and adjust to, shaftsthat are deflected by high hydraulicloads. Optimum bearing alignment,

under load, maintains the large-areabearing support required for minimumwear and maximum life of bearingsand pump.

Molded sealing gland madeof rubber or Viton*. F20 PumpGlass-filled nylon retainerprevents extrusion of sealinggland, has high temperaturestability. Flat side faces steelside of wear plate.

* Registered trademark of DuPont Co.

High pressure meteringnotches reduce pulsations, quiet pumpand system.

Groove providesforced-feed bearing lubrication.

Bearing surfacefaces gears, resistsseizures.

Decompression notchesreduce pressure spikes, quiet system.

3

Inletport


PERFORMANCE SPECIFICATIONS FOR F20/F30 PUMPS4

Singleand

thru-drivepumps

Modelseries

F20andFT20

F30andFT30

Pumpsize

791113151719212427

18212528303235404550

cc

23293643485562687787

5868809197104113129145161

cu. in.

1.411.792.182.602.943.333.774.134.715.30

3.544.134.915.515.896.306.887.868.849.82

bar

276276276276276250228207190170

276276276276276250250228190170

psi

4000400040004000400036253300300027002375

4000400040004000400036253400290025502300

rpm

3600340032003000280025002500250025002300

3000300030002750250025002500240023002200

rpm*

1000800600600600600600600600600

600600600600600600600600600600

l/min

75.790.8105.9117.3124.9128.7147.6162.7185.4193.0

166.5193.0230.9214.0230.9245.0272.5299.0325.5344.4

gpm

20242831333439434951

44516157616572798691

kW

37445157606257575349

7790107959899951049287

hp

50596876808376767166

104121144128131133127139123116

Theoreticaldisplacement

perrevolution

Ratedpressure

Ratedspeed @

ratedpressure &

.17 bar (5” Hg)vacuum inlet

Minimumspeed @

ratedpressure

Typicaldelivery@ ratedspeed &pressure

Typicalinput

power @ rated

speed &pressure

Doublepumpmodelseries

F2020

F3020

F3030

Same as for F20 and FT20 above.Same as for F30 and FT30 above.

Shaft-end pump Cover-end pump

Pump sizes and ratings †

* Lower speeds are permissable when operating below rated pressure.

Same as for F20 and FT20 above.

Same as for F30 and FT30 above.

† Rated speed of double pump is governedby pump with lower speed rating. If deliveriesof both pumps are combined, rated pressureis governed by pump with lower pressure rating.

EfficiencyDepending on displacement, speed andpressure, volumetric efficiency is 81-98%and overall efficiency is 71-92% with SAE10W oil at 49°C (120°F).

Inlet conditionsPressure on the inlet should not exceed 1bar (15 psi). Under continuous operation,inlet vacuum should not exceed 0.17 bar(5”Hg).

Operating temperatureUnder continuous operation, a maximumof 96°C (205°F) is recommended. Themaximum temperature for cyclic or intermittent operation is 107°C (225°F).

Fluids and filtrationFor applications requiring fire resistant fluids, water glycols, water in-oil emulsionsand synthetics may be used at slightlyreduced ratings. Fluid should be selected

with an operating viscosity similar to thepetroleum oil described above. For application assistance, consult your Haldex representative.

The system should be filtered to provide anISO code (proposed) cleanliness level of19/16. A 10-micron filter sized to accommodate full system return line flow,is recommended for most operating environments. Severe conditions mayrequire greater efficiency from the filter.


TABLE OF CONTENTS

Description, Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 & 3

Specifications and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation Dimensions / Model CodesF20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 7F30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 9FT20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 11FT30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 13F2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 - 15F2020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 17F3020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 19F3030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21F202020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 - 23F303030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 - 25F200909 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 - 27F202009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 - 29F302020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 - 31F303020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 - 33FT2020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 - 35FT3030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37

Mounting Flanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Drive Shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Rear Mounting Flanges for Thru-Drive Pumps . . . . . . . . . . . . . . . . . . . . . . .40

Rear Couplings for Thru-Drive Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Performance Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Haldex Product Offering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

5


F20

5.304.714.133.773.332.942.602.181.791.41CIR

272421191715131197

DISPLACEMENTCODE

7.957.707.437.267.066.896.736.546.366.18

A(in.)

6.406.155.885.715.515.345.184.994.814.63

B(in.)

.37[9.39]

.50[12.7]

A

Ø

6.30 [160.02]

6.89[175.01]

2X Ø .56[14.23]

2X .88[22.35]

3.03[76.96]

3.21[81.53]

6

4.0003.998[101.60][101.55]

-B-

B

C

87776862554843362923CC

201.9195.6188.7184.4179.3175.0170.9166.1161.5157.0

A(mm)

162.6156.2149.4145.0140.0135.6131.6126.7122.2117.6

B(mm)

168.1161.8154.9150.6145.5141.2137.2132.3127.8123.2

C(mm)

6.626.376.105.935.735.565.405.215.034.85

C(in.)

5.75[146.05]

2.88[73.15]

FRONT VIEW SIDE VIEW

REAR VIEW

All dimensions shown are for referenceonly. Consult factory for your specificconfiguration.


EXAMPLE:(F3)- F20- W- 2 -D- 15-B -1- A -12- A- 10 - L

Model Code for F20 Series Single Pumps

Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Out

let

Port

Rear

Cov

erSh

aft

Seal

Driv

e Sh

aft

Port

Loc

atio

nsD

esig

nRo

tatio

n

1 2 3 4 5 6 7 8 9 10 11 12 13

7

ORDERING INFORMATIONEach option has been assigned an order code -- listed in the tables below -- for placement inthe sequence shown at right.

1 (Special Seals)Order Code DescriptionF3 Viton SealOmit Standard

2 (Series)Order Code DescriptionF20 F20 Series Single Gear Pump

3 (Mount Type)Order Code DescriptionD Dry Mounting Flange (shorter length, single shaft seal)W Wet Mounting Flange (pilot diameter sealing and provides for

optional double shaft seal)S Single Shaft Seal Short Mount

4 (Front Cover)Order Code Description1 SAE “A” 2-Bolt Mount (G20W only)2 SAE “B” 2-Bolt Flange6 SAE B 2/4-Bolt Combination Mount (G20W only)8 SAE C 2/4-Bolt Mount 31 SAE “A” 2-Bolt Mount w/Outboard Ball Bearing32 SAE “B” 2-Bolt Mount w/Outboard Ball Bearing

5 (Inlet Port)Order Code DescriptionB 1.00”, SAE 4-Bolt Split FlangeC 1.25”, SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16” - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

6 (Displacements)

Order Code Cm3/In3 Order Code Cm3/In3

7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

7 (Outlet Port)Order Code DescriptionA .750”, SAE 4-Bolt Split FlangeB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875 - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Cover)Order Code Description1 Standard Single Pump Rear Cover (no options)

9 (Shaft Seal)Order Code DescriptionA SingleB DoubleJ Double, Outer InvertedX None

10 (Drive Shaft)Order Code Description1 SAE B Straight Keyed, .875 Diameter, 1.312 Ext.3 Straight Keyed with Thread (.625” - 18 UNC)5 Tapered Threaded (1.50” taper per foot)7 Tapered Keyed/Threaded (.625” - 18 UNC, 1.50” taper per foot)12 SAE B 13-Tooth Spline, Flat Root-Side Fit17 SAE “A” 9-Tooth Spline, Flat Root-Side Fit21 SAE “BB” Straight Keyed, 1.00” diameter, 1.50” ext.99 SAE “BB” 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.

11 (Port Locations)Order Code DescriptionA Side Inlet / Side OutletB Side Inlet / Rear OutletC Rear Inlet / Side OutletD Rear Inlet / Rear Outlet

12 (Design Designation)Order Code Description10 Standard

13 (Rotation)Order Code DescriptionOmit Clockwise RotationL Counterclockwise Rotation


F30

9.569.258.948.638.458.338.218.027.777.58

A(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

50454035323028252118

DISPLACEMENTCODE

7.947.637.327.016.836.716.596.406.155.96

B(in.)

242.8235.0227.1219.2214.6211.6208.5203.7197.4192.5

A(mm)

1611451291131039790816858CC

201.7193.8185.9178.1173.5170.4167.4162.6156.2151.4

B(mm)

.49[12.45]

.50[12.7]

A

5.0004.998[127.0]

[126.95]

Ø

-B-

8

7.64 [194.06]

7.12[180.85]

8.37[212.60]

3.56[90.42]

2X .69 [17.53]

2X B

3.63[92.20]

3.43[87.12]

2X 1.05[26.67]


FRONT VIEW SIDE VIEW

REAR VIEW




2 (Series)Order Code DescriptionF30 F30 Series Single Gear Pump

3 (Mount Type)Order Code DescriptionC Standard Designation

4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount6 SAE B 2/4-Bolt Combination Mount7 SAE C 2-Bolt Mount8 SAE C 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionD 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)E 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)W #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadY #30 SAE (2 1/2 - 12) Straight ThreadContact factory for other requirements.

6 (Displacements)


18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

7 (Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)W #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadY #30 SAE (2 1/2 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Cover)Order Code Description2 Standard Single Pump Rear Cover (no options)


EXAMPLE:(F3)- F30- C- 4 - E-30-C - 2- A -12-A- 10 - L

Model Code for F30 Series Single Pumps

Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Out

let

Port

Rear

Cov

erSh

aft

Seal

Driv

e Sh

aft

Port

Pos

ition

sD

esig

nRo

tatio

n

1 2 3 4 5 6 7 8 9 10 11 12 13

9

10 (Drive Shaft)Order Code Description1 SAE C Straight Keyed, 1.250 Diameter, 1.875 Ext.5 Tapered Threaded (1.50” taper per foot)12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements.

11 (Port Positions)Order Code DescriptionA Side Inlet / Side OutletB Side Inlet / Rear OutletC Rear Inlet / Side OutletD Rear Inlet / Rear Outlet


13 (Rotation)Order Code DescriptionL Counterclockwise RotationR Clockwise Rotation


FT20

245.9239.0232.2227.8223.0218.4214.4209.6205.0200.7

A(mm)

5.304.714.133.773.332.942.602.181.791.41CIR

272421191715131197

DISPLACEMENTCODE

9.689.419.148.978.788.608.448.258.077.90

A(in.)

6.426.155.885.715.515.345.184.994.814.63

B(in.)

87776862554843362923CC

163.1156.2149.4145.0140.0135.6131.6126.7122.2117.6

B(mm)

6.646.376.105.935.735.565.405.215.034.85

C(in.)

168.7161.8154.9150.6145.5141.2137.2132.3127.8123.2

C(mm)

6X Ø .4375 1.25[11.11] [31.75]

.37[9.40]

.50[12.7]

.05 X 45°[1.27]

4.0003.998[101.6][101.55]

Ø

-B-

A

Ø4.0034.000

[101.68][101.6]

__> __ .54[13.72] 2X 1.768

[44.91]

2X 3.536[89.81]

2X 1.768[44.91]

2X 1.768[44.91]

2.875[73.03]

__

> __

1/2-13 UNC-2B 1.00[25.4]

__> __

Ø4.2254.215

[107.32][107.06]

__> __ .085.081[2.16][2.06]

3.00[76.2]

2X Ø .562[14.27]

6.29[159.77]

2X 3.44[87.38]

2.875[73.03]

ROTATIONCW

10

2.875[73.03]

2.84[72.14]

B

C

2X 3.44[87.38] 2.875

[73.03]

3.92[99.57]

2.59[65.79]


FRONT VIEW

SIDE VIEW

REAR VIEW


EXAMPLE:(F3)- FT20- W- 2 -D- 9-B - 1- A -12- A- 10 -L

Model Code for FT20 Series Thru Drive Pumps

Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Out

let

Port

Rear

Mou

ntin

g Pa

dSh

aft

Seal

Driv

e Sh

aft

Rear

Cou

plin

gD

esig

nRo

tatio

n

1 2 3 4 5 6 7 8 9 10 11 12 13

11



2 (Series)Order Code DescriptionFT20 FT20 Thru Drive Series Single Gear Pump

3 (Mount Type)Order Code DescriptionW Wet Mounting Flange (pilot diameter sealing and provides for

optional double shaft seal)

4 (Front Cover)Order Code Description1 SAE “A” 2-Bolt Mount2 SAE B 2-Bolt Mount4 SAE “C” 4-Bolt Mount (Contact Factory)6 SAE B 2/4-Bolt Combination Mount (Wet Mount Only)8 SAE C 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionB 1.00”, SAE 4-Bolt Split FlangeC 1.25”, SAE 4-Bolt Split FlangeD 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16” - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

6 (Displacements)


7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

7 (Outlet Port)Order Code DescriptionA .750”, SAE 4-Bolt Split FlangeB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875 - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Mounting Pad)Order Code Description1 SAE “A” 2-Bolt Rear Mounting Pad6 SAE “B” 2/4-Bolt Rear Mounting Pad

Note: A shorter length SAE “A” rear mounting pad option is available, contact factory forinformation.


10 (Drive Shaft)Order Code Description1 SAE B Straight Keyed, .875 diameter, 1.312 ext.12 SAE B 13-Tooth Spline, Flat Root-Side Fit21 SAE “BB” Straight Keyed, 1.00” diameter, 1.50” ext.99 SAE “BB” 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.

11 (Rear Coupling)Order Code DescriptionA SAE “A” CouplingB SAE “B” CouplingBB SAE “BB” CouplingG SAE “A” Coupling 11-Tooth 16/32 DP, Flat Root-Side FitX No Coupling




FT30

50454035323028252118

DISPLACEMENTCODE

11.5411.2310.9210.6210.4310.3110.1910.009.759.56

A(in.)

7.957.647.337.026.846.716.596.406.155.97

B(in.)

.49[12.45]

.50[12.7]

5.0004.998[127.0][126.95]

Ø

-B-

.05 X 45°[1.27]

3.43[87.12]

AØ 4.003

4.000[102.36][101.6]

__> __

.54[13.72]

Ø4.2254.215

[107.32][107.06]

__> __

.085

.081[2.16][2.06]

2X 1.768[44.91]

7.92[201.17] 2.91

[73.91]

2.875[73.03]

6X Ø .500-13 UNC-2B[12.7]

THREAD 1.06 [26.92]__> __

ROTATIONCW

2X Ø .687[17.45]

7.124[180.95]

3.562[90.47]

12

B

C

4.18[106.17]

3.25[82.55]

2X 1.768[44.91]

2.875[73.03]2X 1.768

[44.91]

2X 1.768[44.91]

4.18[106.17]

9.828.847.866.886.305.895.514.914.133.54CIR

1611451291131039790816858CC

293.1285.2277.4269.7264.9261.9258.8254.0247.7242.8

A(mm)

201.9194.1186.2178.3173.7170.4167.4162.6156.2151.6

B(mm)

215.4207.5199.6191.8187.2183.9180.8176.0169.7165.1

C(mm)


FRONT VIEW SIDE VIEW REAR VIEW

SAE “B” 2/4-BOLT REAR MOUNTING PAD

.05 X 45°[1.27]

2X .375-16 UNC-2BROTATION

CW

2X Ø .687[17.45]

7.124[180.95]

3.562[90.47]

.49[12.45]

.50[12.7]

AB

.085

.081[2.16][2.06]

Ø 5.0004.998[127.0][126.95]

-B-

3.250[82.55]

3.430[87.12]

[9.53].700 MIN FULL THREAD

[17.78]

2.094[53.19]

2.094[53.19]

7.61[193.29]

SIDE VIEW REAR VIEW

Ø 3.2533.251[82.63][82.56]

Ø 3.4753.465[88.27][88.01]

FRONT VIEW

SAE “A” 2-BOLT REAR MOUNTING PAD

50454035323028252118

DISPLACEMENTCODE

9.489.178.868.558.378.248.127.937.697.50

A(in.)

7.947.637.337.026.846.716.596.406.155.97

B(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

1611451291131039790816858CC

240.8232.9225.0217.2212.6209.3206.2201.4195.3190.5

A(mm)

201.7193.8186.2178.3173.7170.4167.4162.6156.2151.6

B(mm)

8.488.177.867.557.377.247.126.936.686.50

C(in.)



EXAMPLE:(F3)- FT30 -C- 4 - E- 30-C -6- A -12-B- 10 - L

Model Code for FT30 Series Thru Drive Pumps

Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Out

let

Port

Rear

Mou

ntin

g Pa

dSh

aft

Seal

Driv

e Sh

aft

Rear

Cou

plin

gD

esig

nRo

tatio

n

1 2 3 4 5 6 7 8 9 10 11 12 13

13

10 (Drive Shaft)Order Code Description1 SAE C Straight Keyed, 1.250 diameter, 1.875 ext.12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements.

11 (Rear Coupling)Order Code DescriptionA SAE “A” CouplingB SAE “B” CouplingBB SAE “BB” CouplingC SAE “C” CouplingX No Coupling





2 (Series)Order Code DescriptionFT30 FT30 Thru Drive Series Gear Pump

3 (Mount Type)Order Code DescriptionC Standard Designation

4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount6 SAE B 2/4-Bolt Combination Mount7 SAE C 2-Bolt Mount8 SAE “C” 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionD 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)E 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)W #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadY #30 SAE (2 1/2” - 12) Straight ThreadContact factory for other requirements.

6 (Displacements)


18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

7 (Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.25 , SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)W #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Mounting Pad)Order Code Description1 SAE “A” 2-Bolt Rear Mounting Pad6 SAE “B” 2/4-Bolt Combination Rear Mounting Pad8 SAE “C” 2/4-Bolt Combination Rear Mounting Pad



F2009

W900 SECTIONS

2.522.492.382.262.172.122.032.001.941.86

E(in.)

282723191614111086

DISPLACEMENTCODE

2.732.702.582.472.382.322.232.202.152.09

C(in.)

2.722.692.572.462.372.312.222.192.142.08

D(in.)

3.303.243.012.782.602.492.312.252.142.02

F(in.)

162.8156.0149.1145.0140.0135.4131.3126.5121.9117.6

A(mm)

6.416.145.875.715.515.335.174.984.804.63

A(in.)

163.3156.5149.6145.5140.5135.9131.8127.0122.4118.1

B(mm)

.50[12.7].37

[9.40]

4.0003.998[101.6][101.55]

-B-

Ø

E

2.84[72.14]

ROTATIONCCW

5.750[146.05]

2X Ø .562[14.27]

6.23[158.24]

14

2.875[73.03]

A C

B D

3.00[76.2]

1.71[43.43]

1.71[43.43]

272421191715131197

DISPLACEMENTCODE

6.436.165.895.735.535.355.195.004.824.65

B(in.)

G20 SECTIONS

F

5.304.714.133.773.332.942.602.181.791.41CIR

87776862554843362923CC

1.7091.6471.4031.159.976.854.671.610.488.366CIR

282723191614111086

CC

69.368.665.562.760.558.956.655.954.653.1

C(mm)

69.168.365.362.560.258.756.455.654.452.8

D(mm)

64.063.260.557.455.153.851.650.849.347.2

E(mm)

83.882.376.570.666.063.258.757.254.451.3

F(mm)

All dimensions shown arefor reference only. Consultfactory for your specific con-figuration.

FRONT VIEW

SIDE VIEW

REAR VIEW




2 (Series)Order Code DescriptionF2009 F2009 Series Double Gear Pump



4 (Front Cover)Order Code Description2 SAE “B” 2-Bolt Mount4 SAE C 4-Bolt Mount (contact factory)6 SAE B 2/4-Bolt Combination Mount (wet mount only)8 SAE C 2/4-Bolt Mount (contact factory)

5 (Front Section Inlet Port)Order Code DescriptionC 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)E 2.0 , SAE 4-Bolt Split FlangeEM 2.0 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadContact factory for other requirements.

6 (Displacements, Front Section)


7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

7 (Front Section Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)T #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadNOTE: Metric ports available, contact factory. Contact factory for other requirements.

8 (Displacements, Rear Section)


6- 6 cc/.366 in.3 16- 16 cc/.976 in.3

8- 8 cc/.488 in.3 19- 19 cc/1.159 in.3

10- 10 cc/.610 in.3 23- 23 cc/1.403 in.3

11- 11 cc/.671 in.3 27- 27 cc/1.647 in.3

14- 14 cc/.854 in.3 28- 28 cc/1.709 in.3

9 (Rear Section Inlet Port)Order Code DescriptionX No Rear Inlet Port (single inlet for double pump)

Rear Inlet Port Options (dual inlet for double pump):S 6 cc, #10 SAE (7/8” - 14) Straight ThreadT 8 cc, #12 SAE (1 1/16 - 12) Straight ThreadV 19 cc - 28 cc, #16 SAE (1 5/16 - 12) Straight ThreadA 16 cc - 19 cc, .750 , SAE 4-Bolt Split FlangeB 23 cc - 28 cc, 1.00 , SAE 4-Bolt Split FlangeNOTES: Split flange ports are not available for 6cc - 14 cc sizes.

Metric ports available, contact factory.

EXAMPLE:(F3)-F2009-W- 2 -W-13- T -23-X- A - X-12- E- C -10 - L

Model Code for F2009 Series Double Pumps

Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Fron

t In

let

Port

Dis

plac

emen

tsFr

ont

Out

let

Port

Dis

plac

emen

tsRe

ar In

let

Port

Rear

Out

let

Port

Driv

e Sh

aft

Val

ve O

ptio

nsRe

lief

Val

ve S

ettin

g

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Des

ign

Rota

tion

15

Shaf

t Se

al

10 (Rear Section Outlet Porting)Order Code DescriptionQ 6 cc, #8 SAE (3/4” - 16) Straight ThreadS 8 cc - 16 cc, #10 SAE (7/8” - 14) Straight ThreadT 19 cc - 28 cc, #12 SAE (1 1/16 - 12) Straight ThreadY 16 cc - 19 cc, .500”, SAE 4-Bolt Split FlangeA 23 cc - 28 cc, .750 , SAE 4-Bolt Split FlangeNOTES: Split flange ports are not available for 6cc - 14 cc sizes.

Metric ports available, contact factory.


12 (Drive Shaft)Order Code Description1 SAE B Straight Keyed, .875 Diameter, 1.312 Ext.12 SAE B 13-Tooth Spline, Flat Root-Side Fit21 SAE BB Straight Keyed, 1.00 Diameter, 1.50 Ext.99 SAE BB 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.

13 (Valve Options) **Order Code DescriptionA Tuneable Priority Flow Control Valve, Secondary Flow

LoadableB Tuneable Priority Flow Control Valve, Secondary Bypass

to Pump InletC Tuneable Priority Flow Control Valve w/Relief Valve on

Priority Flow Only, Secondary Flow Loadable (> 4 GPM)CC Tuneable Priority Flow Control Valve w/Relief Valve on

Priority Flow Only, Secondary Flow Loadable (< 4 GPM)D Load Sense Priority Flow Control, Priority Flow Relief

Bypass to Pump InletE Pilot-Operated Relief Valve, Bypass to Tank ExternalX No Valve Option** Contact factory for availability and minimum quantity

requirements for above valve options.

14 (Relief Valve Setting)Order Code Description Order Code Description

A 69 BAR (1000 PSI) G 190 BAR (2750 PSI)B 103 BAR (1500 PSI) H 207 BAR (3000 PSI)C 121 BAR (1750 PSI) I 224 BAR (3250 PSI)D 138 BAR (2000 PSI) J 241 BAR (3500 PSI)E 155 BAR (2250 PSI) K 250 BAR (3750 PSI)F 172 BAR (2500 PSI) L 275 BAR (4000 PSI)




F2020

179.6172.7165.9161.5156.5152.1148.1143.3138.7134.1

B(mm)

166.1159.3152.4148.1143.0138.7134.6129.8125.2123.2

A(mm)

7.076.806.536.366.165.995.835.645.465.28

B(in.)

.50[12.7]

Ø

B D

OUTROTATION

CW

2X Ø .562[14.27]

6.88[174.75]

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

6.546.276.005.835.635.465.305.114.934.85

A(in.)

5.905.685.365.215.014.824.674.474.304.03

C(in.)

16

5.750[146.05]

2.875[73.03]

A C

.37[9.40]

4.0003.998[101.6][101.55]

-B-

2.84[72.14]

3.20[81.28]

6.40[162.56]

6.746.476.206.055.855.665.515.315.145.02

D(in.)

5.304.714.133.773.332.942.602.181.791.41CIR

149.9144.3136.1132.3127.3122.4118.6113.5109.2102.4

C(mm)

171.2164.3157.5153.7148.6143.8140.0134.9130.6127.5

D(mm)

All dimensions shown are for ref-erence only. Consult factory foryour specific configuration.

FRONT VIEW

SIDE VIEW

REAR VIEW


EXAMPLE:(F3)-F2020- W- 6 - E-15-B - + -11- B-12- A- 10 - L


Spec

ial S

eals

Serie

s

Mou

nt

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Fron

t Se

ctio

n O

utle

t

Dis

plac

emen

tsRe

ar S

ectio

n O

utle

t D

rive

Shaf

tSh

aft

Seal

Des

ign

Des

igna

tion

Rota

tion

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Rear

Sec

tion

Inle

t

17




3 (Mount)Order Code DescriptionW Wet Mount Flange (pilot diameter sealing and provides for


4 (Front Cover)Order Code Description2 SAE “B” 2-Bolt Mount3 SAE “B” 4-Bolt Mount (Contact Factory)6 SAE B 2/4-Bolt Combination Mount (wet mount only)8 SAE C 2/4-Bolt Mount

5 (Inlet Port)Order Code DescriptionD 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)E 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)Contact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

SAE Rated Flow, GPM @ 1200 RPM, 100 PSI

7 (Front Section Outlet)Order Code DescriptionA .750 , SAE 4-Bolt Split FlangeAM .750 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)S #10 SAE (.875” - 12) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Section Inlet) (Contact factory)Order Code Description+ None



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

SAE Rated Flow, GPM @ 1200 RPM, 100 PSI

10 (Rear Section Outlet)Order Code DescriptionA .750 , SAE 4-Bolt Split FlangeAM .750 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875” - 12) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

11 (Drive Shaft)Order Code Description1 SAE B Straight Keyed, .875 Diameter, 1.312” Ext.12 SAE B 14-Tooth Spline, Flat Root-Side Fit21 SAE BB Straight Keyed, 1.00 Diameter, 1.50 Ext.99 SAE BB 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.



14 (Rotation)Order Code DescriptionR Clockwise RotationL Counterclockwise Rotation


182.6175.8168.9145.0159.8155.2151.4146.3142.0137.4

D(mm)

5.304.714.133.773.332.942.602.181.791.41CIR

F3020

5.715.445.175.014.814.634.474.284.103.93

C(in.)

7.196.926.655.716.296.115.965.765.595.41

D(in.)

8.608.297.807.617.497.367.247.056.816.62

A(in.)

7.368.177.867.527.377.247.126.936.686.50

B(in.)

ROTATIONCW

1611451291131039790816858CC

50454035323028252118

DISPLACEMENTCODE

G30 SECTIONS

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

G20 SECTIONS

18

2X Ø .687[17.45]

7.124[180.95]

3.562[90.47]

.50[12.7]

.49[12.45]

A C

DB

7.62[193.55]

3.25[82.55]

3.43[87.12]

2.84[72.14]

9.828.847.866.886.305.895.514.914.133.54CIR

218.4210.6198.1193.3190.2186.9183.9179.1173.0168.1

A(mm)

186.9207.5199.6191.0187.2183.9180.8176.0169.7165.1

B(mm)

145.0138.2131.3127.3122.2117.6113.5108.7104.199.8

C(mm)


Ø5.0004.998[127.0][126.95]

-B-

FRONT VIEWSIDE VIEW

REAR VIEW


EXAMPLE:(F3)-F3020- W- 7 - E-18-B - + -11-B -12- A- 10 - L


Spec

ial S

eals

Serie

s

Mou

nt

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Fron

t Se

ctio

n O

utle

t

Dis

plac

emen

tsRe

ar S

ectio

n O

utle

t D

rive

Shaf

tSh

aft

Seal

Des

ign

Des

igna

tion

Rota

tion

1 2 3 4 5 6 7 8 9 10 11 12 13

Rear

Inle

t Po

rt

19

10 (Rear Section Outlet)Order Code DescriptionA .750 , SAE 4-Bolt Split FlangeAM .750 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875” - 12) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

11 (Drive Shaft)Order Code Description1 SAE C Straight Keyed, 1.250 Diameter, 1.875 Ext.12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements.









4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount (contact factory)7 SAE C 2-Bolt Mount (contact factory)8 SAE C 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionE 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3.00 , SAE 4-Bolt Split FlangeGM 3.00 , 4-Bolt Metric Split Flange (M16 x 2.0 threads)Y #30 SAE (2 1/2 - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

7 (Front Section Outlet)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 2.00 , SAE 4-Bolt Split FlangeDM 2.00 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Inlet Port) (Contact Factory)Order Code Description+ None



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3


F3030

8.488.167.867.557.377.247.126.936.686.50

B(in.)

7.947.637.337.026.846.716.596.406.155.96

A(in.)

7.196.896.576.266.085.955.835.645.405.22

C(in.)

1611451291131039790816858CC

50454035323028252118

DISPLACEMENTCODE

Ø

OUT

ROTATIONCW

20

2X Ø .687[17.45]

7.124[180.95]

3.562[90.47]

.05 X 45º[1.27]

.49[12.45]

.50[12.7]

A C

DB

5.0004.998[127.0][126.95]

-B-

3.43[87.12]

3.25[82.55]

7.62[193.55]

8.077.777.467.156.976.846.726.536.296.10

D(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

201.7193.8186.2178.3173.7170.4167.4162.6156.2151.4

A(mm)

215.4207.3199.6191.8187.2183.9180.8176.0169.7165.1

B(mm)

182.6175.0166.9159.0154.4151.1148.1143.3137.2132.6

C(mm)

205.0197.4189.5181.6177.0173.7170.7165.9159.8154.9

D(mm)

All dimensions shown are for ref-erence only. Consult factory foryour specific configuration.

FRONT VIEWSIDE VIEW

REAR VIEW


EXAMPLE:(F3)-F3030- W- 7 - E-30-B - + -30-B -12- A- 10 - L


Spec

ial S

eals

Serie

s

Mou

nt

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

Fron

t O

utle

t Po

rt

Dis

plac

emen

tsRe

ar O

utle

t Po

rtD

rive

Shaf

tSh

aft

Seal

Des

ign

Des

igna

tion

Rota

tion

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Rear

Inle

t Po

rt

21

10 (Rear Outlet Port)Order Code DescriptionA .750 , SAE 4-Bolt Split FlangeAM .750 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)V #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

11 (Drive Shaft)Order Code Description1 SAE C Straight Keyed, 1.250 Diameter, 1.875 Ext.12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements.









4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount (contact factory)7 SAE C 2-Bolt Mount (contact factory)8 SAE C 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionE 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3.00 , SAE 4-Bolt Split FlangeGM 3.00 , 4-Bolt Metric Split Flange (M16 x 2.0 threads)Y #30 SAE (2 1/2 - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

7 (Front Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 2.00 , SAE 4-Bolt Split FlangeDM 2.00 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

8 (Rear Inlet Port) (Contact Factory)Order Code Description+ None



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3


F202020

6.546.276.005.835.635.465.305.114.934.75

A(in.)

7.076.806.536.366.165.995.835.645.465.28

B(in.)

6.035.785.495.325.124.954.794.604.424.24

C(in.)

5.385.114.844.674.474.304.143.953.773.59

D(in.)

6.746.476.206.035.835.665.505.315.134.95

E(in.)

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

OUT

2X Ø .562[14.27]

22

5.750[146.05]

2.875[73.03]

ROTATIONCW

.37[9.40]

.50[12.7]

A C D

B

Ø

2.84[72.14]

3.20[81.28]

6.40[162.56]

E

4.0003.998[101.6][101.55]

-B-

5.304.714.133.773.332.942.602.181.791.41CIR

166.1159.3152.4148.1143.0138.7134.6129.8125.2120.7

A(mm)

179.6172.7165.9161.5156.5152.1148.1143.3138.7134.1

B(mm)

153.2146.8139.4135.1130.0125.7121.7116.8112.3107.7

C(mm)

136.7129.8122.9118.6113.5109.2105.2100.395.891.2

D(mm)

171.2164.3157.5153.2148.1143.8139.7134.9130.3125.7

E(mm)

All dimensions shown are forreference only. Consult factoryfor your specific configuration.

FRONT VIEW

SIDE VIEW

REAR VIEW

(6.88)[174.75]


EXAMPLE:(F3)F202020- W- 6 - E-15- B -E -11- B - + - 9 - B- 99- A- 10-L

Model Code for F202020 Series Triple Pumps

Spec

ial S

eals

Serie

s

Mou

nt

Fron

t C

over

Firs

t In

let

Port

Dis

plac

emen

tsFr

ont

Sect

ion

Out

let

Seco

nd S

ectio

n In

let

Dis

plac

emen

tsSe

cond

Out

let

Third

Sec

tion

Inle

tD

ispl

acem

ents

Driv

e Sh

aft

Shaf

t Se

alD

esig

nRo

tatio

n

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Third

Out

let

23

11 (Third Section Inlet) (Contact Factory)Order Code Description+ None



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

13 (Third Outlet)Order Code DescriptionA .750 , SAE 4-Bolt Split FlangeB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)S #10 SAE (.875” - 12) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

14 (Drive Shaft)Order Code Description21 SAE BB Straight Keyed, 1.00 Diameter, 1.50 Ext.99 SAE BB 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements






2 (Series)Order Code DescriptionF202020 F202020 Series Triple Gear Pump



4 (Front Cover)Order Code Description6 SAE B 2/4-Bolt Combination Mount (wet mount only)

5 (First Inlet Port)Order Code DescriptionE 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)Contact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

7 (Front Section Outlet)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)T #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

8 (Second Section Inlet)Order Code DescriptionD 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)E 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)Contact factory for other requirements.

9 (Displacements, Center Section)


7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

10 (Second Outlet)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)T #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.


F303030

7.587.276.966.656.476.346.236.045.795.60

C(in.)

8.087.777.467.156.976.846.726.536.286.10

E(in.)

1611451291131039790816858CC

50454035323028252118

DISPLACEMENTCODE

7.947.637.337.026.846.716.596.406.155.96

A(in.)

8.488.167.867.557.377.247.126.936.686.50

B(in.)

Ø

ROTATIONCW

2X Ø .687[17.45]

24

7.124[180.95]

3.562[90.47]

7.62[193.55]

.49[12.45]

.50[12.7]

A C D

3X 3.25[82.55]

2X 3.43[87.12]

EB

5.0004.998[127.0][126.95]

-B-

7.196.886.576.266.085.955.845.655.405.21

D(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

201.7193.8186.2178.3173.7170.4167.4162.6156.2151.4

A(mm)

215.4207.3199.6191.8187.2183.9180.9176.0169.7165.1

B(mm)

192.5184.7176.8168.9164.3161.0158.2153.4147.1142.2

C(mm)

182.6174.8166.9159.0154.4151.1148.3143.5137.2132.3

D(mm)

205.2197.4189.5181.6177.0173.7170.7165.9159.5154.9

E(mm)

All dimensions shown are for refer-ence only. Consult factory for yourspecific configuration.

FRONT VIEW

SIDE VIEW


Model Code for F303030 Series Triple PumpsEXAMPLE:(F3)F303030-W- 7 - E- 30- B -E -25- B - + - 9 - B- 12- A- 10-L

Spec

ial S

eals

Serie

s

Mou

nt

Fron

t C

over

Firs

t In

let

Port

Dis

plac

emen

tsFi

rst

Out

let

Por

tSe

cond

Inle

t Po

rtD

ispl

acem

ents

Seco

nd O

utle

t Po

rtTh

ird In

let

Port

Dis

plac

emen

ts

Driv

e Sh

aft

Shaf

t Se

alD

esig

nRo

tatio

n

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Third

Out

let

Port

25

10 (Second Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadContact factory for other requirements.

11 (Third Inlet Port) (Contact Factory)Order Code Description+ None



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

13 (Third Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadContact factory for other requirements.

14 (Drive Shaft)Order Code Description1 SAE C Straight Keyed, 1.250 Diameter, 1.875 Ext.12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements









4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount7 SAE C 2-Bolt Mount 8 SAE C 2/4-Bolt Combination Mount

5 (First Inlet Port)Order Code DescriptionE 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3.00 , SAE 4-Bolt Split FlangeGM 3.00 , 4-Bolt Metric Split Flange (M16 x 2.0 threads)Y #30 SAE (2 1/2 - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

7 (First Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

8 (Second Inlet Port)Order Code DescriptionE 2.00 , SAE 4-Bolt Split FlangeEM 2.00 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.50 , SAE 4-Bolt Split FlangeFM 2.50 , 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3.00 , SAE 4-Bolt Split FlangeGM 3.00 , 4-Bolt Metric Split Flange (M16 x 2.0 threads)



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3


2.522.492.382.262.172.122.032.001.941.86

G(in.)

69.168.365.362.560.258.756.455.654.452.8

D(mm)

F200909

W900 SECTIONS

ROTATIONCW

6.29[159.77]

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

6.416.145.875.715.515.335.174.984.804.63

A(in.)

6.436.165.895.735.535.355.195.004.824.65

B(in.)

G20 SECTIONS

282723191614111086

DISPLACEMENTCODE

2.732.702.582.472.382.322.232.202.152.09

C(in.)

2.722.692.572.462.372.312.222.192.142.08

D(in.)

3.623.543.333.092.912.802.612.562.442.34

E(in.)

3.303.243.012.782.602.492.312.252.142.02

F(in.)

282723191614111086

CC

26

3.44[87.38]

2.875[73.03]

3.44[87.38]

2.875[73.03]

2X Ø .562[14.27]

.37[9.40]

.50[12.7]

A C E

G

FDB

2.84[72.14]

3.00[76.2]

Ø4.0003.998[101.6][101.55]

-B-

5.304.714.133.773.332.942.602.181.791.41CIR

162.8156.0149.1145.0140.0135.4131.3126.5121.9117.6

A(mm)

163.3156.5149.6145.5140.5135.9131.8127.0122.4118.1

B(mm)

1.7091.6471.4031.159.976.854.671.610.488.366CIR

69.368.665.562.760.558.956.655.954.653.1

C(mm)

91.989.984.678.573.971.166.365.062.059.4

E(mm)

83.882.376.570.666.063.258.757.254.451.3

F(mm)

64.063.260.557.455.153.851.650.849.347.2

G(mm)

All dimensions shown are for reference only. Consultfactory for your specific configuration.

FRONT VIEW

SIDE VIEW

REAR VIEW

2X 1.71[43.43]

2X 1.71[43.43]

EXAMPLE:(F3)-F200909-W- 2 - W-13- T -23-Y- Q -11- A- 1 - B -10- L

Des

ign

Des

igna

tion


Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Fron

t Se

ctio

n In

let

Port

Dis

plac

emen

ts,

Fron

t Se

ctio

nFr

ont

Sect

ion

Out

let

Port

Dis

plac

emen

ts,

Cen

ter

Sect

ion

Rear

Sec

tion

Out

let

Port

ing

Cen

ter

Sect

ion

Out

let

Port

ing

Dis

plac

emen

ts,

Rear

Sec

tion

Rear

Sec

tion

Out

let

Port

Driv

e Sh

aft

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Shaf

t Se

alD

esig

n D

esig

natio

n






4 (Front Cover)Order Code Description2 SAE “B” 2-Bolt Mount4 SAE C 4-Bolt Mount (contact factory)6 SAE B 2/4-Bolt Combination Mount (wet mount only)8 SAE C 2/4-Bolt Mount (contact factory)

5 (Front Section Inlet Port)Order Code DescriptionC 1.250 , SAE 4-Bolt Split FlangeCM 1.250 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadContact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

7 (Front Section Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)T #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.



6- 6 cc/.366 in.3 16- 16 cc/.976 in.3

8- 8 cc/.488 in.3 19- 19 cc/1.159 in.3

10- 10 cc/.610 in.3 23- 23 cc/1.403 in.3

11- 11 cc/.671 in.3 27- 27 cc/1.647 in.3

14- 14 cc/.854 in.3 28- 28 cc/1.709 in.3

GPM @ 1200 RPM, 100 PSI

9 (Rear Section Outlet Porting)Order Code DescriptionA 23 cc - 28 cc, .750 , SAE 4-Bolt Split FlangeQ 6 cc, #8 SAE (3/4” - 16) Straight ThreadS 8 cc - 16 cc, #10 SAE (7/8” - 14) Straight ThreadT 19 cc - 28 cc, #12 SAE (1 1/16 - 12) Straight ThreadY 16 cc - 19 cc, .5”, SAE 4-Bolt Split FlangeContact factory for other requirements.

27

10 (Center Section Outlet Porting)Order Code DescriptionA 23 cc - 28 cc, .750 , SAE 4-Bolt Split FlangeQ 6 cc, #8 SAE (3/4” - 16) Straight ThreadS 8 cc - 16 cc, #10 SAE (7/8” - 14) Straight ThreadT 19 cc - 28 cc, #12 SAE (1 1/16 - 12) Straight ThreadV 19 cc - 28 cc, #16 SAE (1 5/16 - 14) Straight ThreadY 16 cc - 19 cc, .5”, SAE 4-Bolt Split Flange



6- 6 cc/.366 in.3 16- 16 cc/.976 in.3

8- 8 cc/.488 in.3 19- 19 cc/1.159 in.3

10- 10 cc/.610 in.3 23- 23 cc/1.403 in.3

11- 11 cc/.671 in.3 27- 27 cc/1.647 in.3

14- 14 cc/.854 in.3 28- 28 cc/1.709 in.3

GPM @ 1200 RPM, 100 PSI

12 (Rear Section Outlet Port)Order Code DescriptionA 23 cc - 28 cc, .750 , SAE 4-Bolt Split FlangeQ 6 cc, #8 SAE (3/4” - 16) Straight ThreadS 8 cc - 16 cc, #10 SAE (7/8” - 14) Straight ThreadT 19 cc - 28 cc, #12 SAE (1 1/16 - 12) Straight ThreadY 16 cc - 19 cc, .5”, SAE 4-Bolt Split FlangeContact factory for other requirements.

13 (Drive Shaft)Order Code Description1 SAE B Straight Keyed, .875 Diameter, 1.312 Ext.12 SAE B 13-Tooth Spline, Flat Root-Side Fit21 SAE BB Straight Keyed, 1.00 Diameter, 1.50 Ext.99 SAE BB 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.

14 (Shaft Seal)Order Code DescriptionA SingleB DoubleJ Double, Outer InvertedX NoneContact Applications Engineer for Valve Options.

15 (Design Designation)Order Code Description10 Standard11 Sealed Between Sections




F202009

282723191614111086

CC

69.368.665.562.760.558.956.956.154.653.1

E(mm)

W900 SECTIONS7.066.806.536.366.165.995.835.645.465.28

B(in.)

Ø

ROTATIONCW

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

6.536.276.005.835.635.465.305.114.934.75

A(in.)

G20 SECTIONS

2.732.702.582.472.382.322.242.212.152.09

E(in.)

2.722.692.572.462.372.312.232.492.142.08

F(in.)

2.522.492.382.262.172.122.032.001.941.86

G(in.)

5.905.645.375.205.004.834.674.484.304.12

C(in.)

5.385.124.854.684.484.314.153.963.783.60

D(in.)

28

6.29[159.77]

3.92[99.57]

3.44[87.38] 2.875

[73.03]

3.44[87.38]

2.875[73.03]

2X Ø .562[14.27]

.37[9.40]

.50[12.7]

A C E

G

FDB

4.0003.998[101.6][101.55]

-B-

2X 2.84[72.14]

3.20[81.28]

3.00[76.2]

5.304.714.133.773.332.942.602.181.791.41CIR

165.9159.3152.4148.1143.0138.7134.6129.8125.2120.7

A(mm)

179.3172.7165.9161.5156.5152.1148.1143.3138.7134.1

B(mm)

149.9143.3136.4132.1127.0122.7118.6113.8109.2104.6

C(mm)

136.7130.0123.2118.9113.8109.5105.4100.696.091.4

D(mm)

1.7091.6471.4031.159.976.854.671.610.488.366CIR

69.168.365.362.560.258.756.663.254.452.8

F(mm)

64.063.26.0557.455.153.851.650.849.347.2

G(mm)

282723191614111086

DISPLACEMENTCODE


FRONT VIEW

SIDE VIEW

REAR VIEW

1.71[43.43]

1.71[43.43]


Cen

ter

Sect

ion

Out

let

Port

ing

Rota

tion

EXAMPLE:(F3)-F202009-W- 2 -F- 13- T 13- V- A -23- Q- 21 -B -10- L


Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Fron

t In

let

Port

Dis

plac

emen

ts,

Fron

t Se

ctio

nFr

ont

Out

let

Port

Dis

plac

emen

ts,

Cen

ter

Sect

ion

Rear

Sec

tion

Inle

t Po

rtD

ispl

acem

ents

, Re

ar S

ectio

nRe

ar S

ectio

n O

utle

t Po

rtin

gD

rive

Shaf

t

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Shaf

t Se

alD

esig

n D

esig

natio

n

10 (Rear Section Inlet Port)Order Code DescriptionA 16 cc - 19 cc, .75 , SAE 4-Bolt Split FlangeB 23 cc - 28 cc, 1”, SAE 4-Bolt Split FlangeStraight ThreadS 6 cc, #10 SAE (7/8” - 14) Straight ThreadT 8 cc - 16 cc, #12 SAE (1 1/16 - 12) Straight ThreadV 19 cc - 28 cc, #16 SAE (1 5/16 - 14) Straight Thread



6- 6 cc/.366 in.3 16- 16 cc/.976 in.3

8- 8 cc/.488 in.3 19- 19 cc/1.159 in.3

10- 10 cc/.610 in.3 23- 23 cc/1.403 in.3

11- 11 cc/.671 in.3 27- 27 cc/1.647 in.3

14- 14 cc/.854 in.3 28- 28 cc/1.709 in.3

GPM @ 1200 RPM, 100 PSI

12 (Rear Section Outlet Port)Order Code DescriptionA 23 cc - 28 cc, .75 , SAE 4-Bolt Split FlangeQ 6 cc, #8 SAE (3/4” - 16) Straight ThreadS 8 cc - 16 cc, #10 SAE (7/8” - 14) Straight ThreadT 19 cc - 28 cc, #12 SAE (1 1/16 - 12) Straight ThreadY 16 cc - 19 cc, .5”, SAE 4-Bolt Split FlangeContact factory for other requirements.

13 (Drive Shaft)Order Code Description21 SAE BB Straight Keyed, 1.00 Diameter, 1.50 Ext.99 SAE BB 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.


15 (Design Designation)Order Code Description10 Standard11 Sealed Between G20 and 09 Sections

16 (Rotation)Order Code DescriptionL Counterclockwise RotationR Clockwise RotationContact factory for other requirements.




3 (Mount Type)Order Code DescriptionW Wet Mounting Flange (pilot diameter sealing and provides for

optional double shaft seal)Contact factory for other requirements.

4 (Front Cover)Order Code Description2 SAE “B” 2-Bolt Mount6 SAE B 2/4-Bolt Combination Mount (wet mount only)8 SAE C 2/4-Bolt Mount

5 (Front Section Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)Contact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

7 (Front Section Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.25 , SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)T #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

9 (Center Section Outlet Porting)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.25 , SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)T #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

29


161.3154.4147.6143.3138.2133.9129.8125.0120.4115.8

C(mm)

F302020

Ø

ROTATIONCW

2X Ø .687[17.45]

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

G20 SECTIONS

1611451291131039790816858CC

50454035323028252118

DISPLACEMENTCODE

G30 SECTIONS

30

7.124[180.95]

3.562[90.47]

7.62[193.55]

.49[12.45]

.50[12.7]

.05 X 45º[1.27]

A B D

C E

3.25[82.55]2X 2.84

[72.14]

3.20[81.28]

3.44[87.38]

5.0004.998[127.0][126.95]

-B-

8.488.177.877.567.387.257.136.946.696.51

A(in.)

5.825.555.285.114.914.744.584.394.214.03

B(in.)

6.356.085.815.645.445.275.114.924.744.56

C(in.)

5.915.645.375.205.004.834.674.484.304.12

D(in.)

6.756.486.216.045.845.675.515.325.144.96

E(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

215.4207.5199.9192.0187.5184.2181.1176.3169.9165.4

A(mm)

5.304.714.133.773.332.942.602.181.791.41CIR

147.8141.0134.1129.8124.7120.4116.3111.5106.9102.4

B(mm)

150.1143.3136.4132.1127.0122.7118.6113.8109.2104.6

D(mm)

171.5164.6157.7153.4148.3144.0140.0135.1130.6126.0

E(mm)


FRONT VIEW

SIDE VIEW

10 (Second Outlet Port)Order Code DescriptionA .75 , SAE 4-Bolt Split FlangeAM .75 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875” - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

11 (Third Inlet Port)Order Code Description+ None



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

13 (Third Outlet Port)Order Code DescriptionA .75 , SAE 4-Bolt Split FlangeAM .75 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875” - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

14 (Drive Shaft)Order Code Description1 SAE “C” Straight Keyed, 1.25” Dia., 1.875” Ext.12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements.




EXAMPLE:(F3)-F302020-W- 7 - E-25-B -E- 11- B- + - 9- B- 12 - A -10-L

Dis

plac

emen

ts,

Cen

ter

Rota

tion


Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Firs

t In

let

Port

Dis

plac

emen

ts,

Fron

t Fi

rst

Out

let

Port

Seco

nd In

let

Port

Seco

nd O

utle

t Po

rtTh

ird In

let

Port

Dis

plac

emen

ts,

Rear

Driv

e Sh

aft

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Shaf

t Se

alD

esig

n D

esig

natio

n

Third

Out

let

Port




3 (Mount Type)Order Code DescriptionW Wet Mounting Flange

4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount 7 SAE C 2-Bolt Mount8 SAE “C” 2/4-Bolt Combination Mount

5 (First Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3 , SAE 4-Bolt Split FlangeGM 3 , SAE 4-Bolt Metric Split Flange (M16 x 2.0 threads)Y #30 SAE (2-1/2” - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

GPM @ 1200 RPM, 100 PSI

7 (First Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.25 , SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

8 (Second Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)Contact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

31



F303020

144.8137.9131.1126.7121.7117.3113.3111.5103.999.3

E(mm)

G20 SECTIONS

8.127.817.507.197.016.886.776.586.336.14

B(in.)

G30 SECTIONS

8.478.167.867.557.377.247.126.936.686.50

C(in.)

7.597.286.976.666.486.356.246.055.805.61

D(in.)

Ø

ROTATIONCW

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

1611451291131039790816858CC

50454035323028252118

DISPLACEMENTCODE

32

7.58[192.53]

2X Ø .640[16.26] 3.27

[83.06]2X 2.65[67.31]

2.254[57.25]

2.254[57.25]

2.254[57.25]

2.254[57.25]

2X R .62[15.75]

4.508[114.50]

2X 6.40[162.56]

2X R 3.20[81.28]

.49[12.45]

.50[12.7]

A B E

FDC

2X 3.25[82.55]2.84

[72.14]

2X 3.43[87.12]

.05 X 45º[1.27]

5.0004.998[127.0][126.95]

-B-

7.947.637.337.026.846.716.596.406.155.97

A(in.)

5.705.435.164.994.794.624.464.394.093.91

E(in.)

7.076.806.536.366.165.995.835.645.465.28

F(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

201.7193.8186.2178.3173.7170.4167.4162.6156.2151.6

A(mm)

206.2198.4190.5182.6178.1174.8172.0167.1160.8156.0

B(mm)

215.1207.3199.6191.8187.2183.9180.8176.0169.7165.1

C(mm)

192.8184.9177.0169.2164.6161.3158.5153.7147.3142.5

D(mm)

5.304.714.133.773.332.942.602.181.791.41CIR

179.6172.7165.9161.5156.5152.1148.1143.3138.7134.1

F(mm)


FRONT VIEW

SIDE VIEW

Dis

plac

emen

ts,

Cen

ter

Rota

tion

EXAMPLE:(F3)-F303020-W- 7 -E- 30-B -E- 25- B- + - 9- B- I2 - A -10-L


Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Firs

t In

let

Port

Dis

plac

emen

ts,

Fron

t Fi

rst

Out

let

Port

Seco

nd In

let

Port

Seco

nd O

utle

t Po

rtTh

ird In

let

Port

Dis

plac

emen

ts,

Rear

Driv

e Sh

aft

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Shaf

t Se

alD

esig

n D

esig

natio

n

Third

Out

let

Port

10 (Second Outlet Port)Order Code DescriptionB 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)C 1.25 , SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadContact factory for other requirements.

11 (Third Inlet Port) (Contact Factory)Order Code Description+ None



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

13 (Third Outlet Port)Order Code DescriptionA .75 , SAE 4-Bolt Split FlangeAM .75 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)B 1.00 , SAE 4-Bolt Split FlangeBM 1.00 , SAE 4-Bolt Metric Split Flange (M10 x 1.50 threads)S #10 SAE (.875” - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

14 (Drive Shaft)Order Code Description1 SAE “C” Straight Keyed, 1.25” Dia., 1.875” Ext.12 SAE C 14-Tooth Spline, Flat Root-Side Fit34 SAE C 14-Tooth SplineContact factory for other requirements.







3 (Mount Type)Order Code DescriptionW Wet Mounting Flange

4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount 7 SAE C 2-Bolt Mount8 SAE “C” 2/4-Bolt Combination Mount

5 (First Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3 , SAE 4-Bolt Split FlangeGM 3 , SAE 4-Bolt Metric Split Flange (M16 x 2.0 threads)Y #30 SAE (2-1/2” - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

GPM @ 1200 RPM, 100 PSI

7 (First Outlet Port)Order Code DescriptionC 1.25 , SAE 4-Bolt Split FlangeCM 1.25 , SAE 4-Bolt Metric Split Flange (M10 x 1.5 threads)D 1.50 , SAE 4-Bolt Split FlangeDM 1.50 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

8 (Second Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3 , SAE 4-Bolt Split FlangeGM 3 , SAE 4-Bolt Metric Split Flange (M16 x 2.0 threads)Contact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

GPM @ 1200 RPM, 100 PSI

33



7.076.806.536.366.165.995.835.645.465.28

C(in.)

FT2020

179.6172.7165.9161.5156.5152.1148.1143.3138.7134.1

C(mm)

G20 SECTIONS

150.1143.3136.4132.1127.0122.7118.6113.8109.2104.6

B(mm)

15.7015.1714.6314.3013.9013.5513.2312.8412.4912.14

E(in.)

Ø

ROTATIONCW

6.29[159.77]

Ø

1/2-13UNC-2B

87776862554843362923CC

272421191715131197

DISPLACEMENTCODE

34

3.92[99.57]

2.59[65.79]

2.875[73.03]

2X 3.44[87.38]

2.875[73.03]

2X 3.44[87.38]

2X Ø .562[14.27]

.37[9.40]

.50[12.7]

.05 X 45º[1.27]

AB

E

DC

4.0003.998[101.6][101.55]

-B-

2X 2.84[72.14]

3.20[81.28]

3.00[76.2]

4.2254.215

[107.32]

.085

.081[2.16][2.06]

6X Ø .4375[11.11]

1.25[31.75]

1.25[31.75]

2X 1.768[44.91]

2X 1.768[44.91]

2X 3.536[89.81]

2.875[73.03]

2.875[73.03]

Ø 4.0034.000

[102.36][101.6]

.54[13.72]

2X 1.768[44.91]

6.546.276.005.835.635.465.305.114.934.75

A(in.)

5.915.645.375.205.004.834.674.484.304.12

B(in.)

5.605.335.064.894.694.524.364.173.993.81

D(in.)

5.304.714.133.773.332.942.602.181.791.41CIR

166.1159.3152.4148.1143.0138.7134.6129.8125.2120.7

A(mm)

142.2135.4128.5124.2119.1114.8110.7105.9101.396.8

D(mm)

398.8385.3371.6363.2353.1344.2336.0326.1317.2308.4

E(mm)

All dimensions shownare for reference only.Consult factory for yourspecific configuration.

FRONT VIEW

SIDE VIEW

REAR VIEW


Rear

Sec

tion

Out

let

Port

EXAMPLE:(F3)-FT2020- W- 2 - E-13-T -21 -V- 1 -B - 11- A - 10- L

Model Code for FT2020 Series Double Pumps

Spec

ial S

eals

Serie

s

Mou

nt T

ype

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

, Fr

ont

Sect

ion

Out

let

Port

Dis

plac

emen

ts,

Rear

Sec

tion

Rear

Mou

ntin

g Pa

dSh

aft

Seal

Driv

e Sh

aft

Rear

Cou

plin

g

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Des

ign

Des

igna

tion

Rota

tion

35



2 (Series)Order Code DescriptionFT2020 FT2020 Series Double Thru Drive Pump

3 (Mount Type)Order Code DescriptionW Wet Mounting Flange (pilot diameter sealing and

provides for option double shaft seal)

4 (Front Cover)Order Code Description1 SAE “A” 2-Bolt Mount2 SAE B 2-Bolt Mount4 SAE “C” 4-Bolt Mount (Contact Factory)6 SAE B 2/4-Bolt Combination Mount8 SAE C 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)Contact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

7 (Outlet Port)Order Code DescriptionA .75 , SAE 4-Bolt Split FlangeB 1 , SAE 4-Bolt Split Flange (M10 x 1.5 threads)BM 1 , SAE 4-Bolt Metric Split Flange (M10 x 1.5 threads)S #10 SAE (.875 - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.



7- 23 cc/1.41 in.3 17- 55 cc/3.33 in.3

9- 29 cc/1.79 in.3 19- 62 cc/3.77 in.3

11- 36 cc/2.18 in.3 21- 68 cc/4.13 in.3

13- 43 cc/2.60 in.3 24- 77 cc/4.71 in.3

15- 48 cc/2.94 in.3 27- 87 cc/5.30 in.3

GPM @ 1200 RPM, 100 PSI

9 (Rear Section Outlet Port)Order Code DescriptionA .75 , SAE 4-Bolt Split FlangeB 1 , SAE 4-Bolt Split Flange (M10 x 1.5 threads)BM 1 , SAE 4-Bolt Metric Split Flange (M10 x 1.5 threads)S #10 SAE (.875 - 14) Straight ThreadT #12 SAE (1 1/16 - 12) Straight ThreadV #16 SAE (1 5/16 - 12) Straight ThreadContact factory for other requirements.

10 (Rear Mounting Pad)Order Code Description1 SAE “A” 2-Bolt Rear Mounting Pad6 SAE “B” 2/4-Bolt Rear Mounting PadNote: SAE “A” rear mounting pad is available with GT30 - 41st design. Contactfactory for information.


12 (Drive Shaft)Order Code Description1 SAE “B” Straight Keyed, .875” Dia., 1.312” Ext.12 SAE “B” 13-Tooth Spline, Flat Root-Side Fit21 SAE “BB” Straight Keyed, 1” Dia., 1.5” Ext.99 SAE “BB” 15-Tooth Spline, Flat Root-Side FitContact factory for other requirements.

13 (Rear Coupling)Order Code DescriptionA SAE “A” CouplingB SAE “B” Coupling




FT3030

192.5184.7176.8168.9164.3161.0158.2153.4147.1142.4

B(mm)

19.1318.5117.8917.2716.9216.6516.4116.0315.5415.17

E(in.)

2X 3.43[87.12]

2X 3.25[82.55]

1611451291131039790816858CC

50454035323028252118

DISPLACEMENTCODE

Ø

6X Ø .500-13 UNC-2B

1.06THREAD

ROTATIONCW

36

2X Ø .687[17.45]

7.124[180.95]

3.562[90.47]

.49[12.45]

.50[12.7]

A BE

4.18[106.17]

4.18[106.17]

DC

.05 X 45º[1.27]

5.0004.998[127.0][126.95]

-B-

2X 1.768[44.91]

Ø4.0034.000[102.36][101.6]

.54[13.72]

7.92[201.17]

2.91[73.91]

2X 1.768[44.91]

2.875[73.03]

2.875[73.03]

Ø4.2254.215

[107.32][107.06]

.085

.081[2.16][2.06]

[12.7]

[26.92]

7.947.637.337.026.846.716.596.406.155.97

A(in.)

7.587.276.966.656.476.346.236.045.795.60

B(in.)

8.488.177.867.557.377.247.126.936.696.50

C(in.)

6.816.506.195.895.705.585.465.275.024.83

D(in.)

9.828.847.866.886.305.895.514.914.133.54CIR

201.7193.8186.2178.3173.7170.4167.4162.6156.2151.6

A(mm)

215.4207.5199.6191.8187.2183.9180.8176.0169.9165.1

C(mm)

173.0165.1157.2149.6144.8141.7138.7133.9127.5122.7

D(mm)

485.9470.2454.4438.7429.8422.9416.8407.2394.7385.3

E(mm)

All dimensions shownare for reference only.Consult factory foryour specific configu-ration.

FRONT VIEW

REAR VIEW

2X 1.768[44.91]

2X 1.768[44.91]

SIDE VIEW


Rear

Sec

tion

Out

let

Port

EXAMPLE:(F3)-FT3030- C- 4 - E- 18-B -28 -X- 6 - A- 12- B -10- L

Model Code for FT3030 Double Thru Drive Pumps

Spec

ial S

eals

Serie

s

Stan

dard

Des

igna

tion

Fron

t C

over

Inle

t Po

rtD

ispl

acem

ents

, Fr

ont

Sect

ion

Fron

t Se

ctio

n O

utle

t Po

rtD

ispl

acem

ents

, Re

ar S

ectio

n

Rear

Mou

ntin

g Pa

dSh

aft

Seal

Driv

e Sh

aft

Rear

Cou

plin

g

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Des

ign

Des

igna

tion

Rota

tion



2 (Series)Order Code DescriptionFT3030 FT3030 Series Double Thru Drive PumpContact factory for other requirements.

3 (Standard Designation)Order Code DescriptionC Standard Designation

4 (Front Cover)Order Code Description4 SAE C 4-Bolt Mount 7 SAE C 2-Bolt Mount 8 SAE C 2/4-Bolt Combination Mount

5 (Inlet Port)Order Code DescriptionE 2 , SAE 4-Bolt Split FlangeEM 2 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)F 2.5 , SAE 4-Bolt Split FlangeFM 2.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)G 3 , SAE 4-Bolt Split FlangeGM 3 , SAE 4-Bolt Metric Split Flange (M16 x 2.0 threads)Y #30 SAE (2 1/2 - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

GPM @ 1200 RPM, 100 PSI

7 (Front Section Outlet Port)Order Code DescriptionB 1 , SAE 4-Bolt Split Flange BM 1 , SAE 4-Bolt Metric Split Flange (M10 x 1.5 threads)C 1.25 , SAE 4-Bolt Split Flange CM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.5 , SAE 4-Bolt Split Flange DM 1.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)V #16 SAE (1 5/16 - 12) Straight ThreadW #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.



18- 58 cc/3.54 in.3 32- 104 cc/6.30 in.3

21- 68 cc/4.13 in.3 35- 113 cc/6.88 in.3

25- 80 cc/4.91 in.3 40- 129 cc/7.86 in.3

28- 91 cc/5.51 in.3 45- 145 cc/8.84 in.3

30- 97 cc/5.89 in.3 50- 161 cc/9.82 in.3

GPM @ 1200 RPM, 100 PSI

37

9 (Rear Section Outlet Port)Order Code DescriptionB 1 , SAE 4-Bolt Split Flange BM 1 , SAE 4-Bolt Metric Split Flange (M10 x 1.5 threads)C 1.25 , SAE 4-Bolt Split Flange CM 1.25 , SAE 4-Bolt Metric Split Flange (M12 x 1.75 threads)D 1.5 , SAE 4-Bolt Split Flange DM 1.5 , SAE 4-Bolt Metric Split Flange (M14 x 2.0 threads)W #20 SAE (1 5/8 - 12) Straight ThreadX #24 SAE (1 7/8 - 12) Straight ThreadContact factory for other requirements.

10 (Rear Mounting Pad)Order Code Description1 SAE “A” 2-Bolt Rear Mounting Pad6 SAE “B” 2/4-Bolt Rear Mounting Pad8 SAE “C” 2/4-Bolt Rear Mounting Pad


12 (Drive Shaft)Order Code Description1 SAE “C” Straight Keyed, 1.25” Dia., 1.875” Ext.12 SAE “C” 14-Tooth Spline, Flat Root-Side Fit34 SAE “C” 14-Tooth SplineContact factory for other requirements.

13 (Rear Coupling)Order Code DescriptionB SAE “B” CouplingC SAE “C” Coupling




Mounting Flanges38

11.94 (.47) R.4 PLACES

9.14 (.36)

9.14 (.36)

95.25 (3.75) Dia.

11.13 (.438) Dia. thru2 places as shown

53.19(2.094)

53.19(2.094)

65.02(2.56)

65.02(2.56)

82.5582.50(3.250)(3.248)

Dia.

12.7 (.50) Mountingflange thickness

6.10(.240)

8.38 (.33)

Seal drain hole

127.00126.95(5.000)(4.998)

Dia.

8.1 (.32)

Seal drain hole

12.7 (.50) Mountingflange thickness

8.1 (.32)

Seal drain hole

J

K

45.7(1.80)

45.7(1.80)

57.25(2.254)

57.25(2.254)

146.05(5.75)

67.31(2.65)

57.25(2.254) 72.9

(2.87)

14.27 (.562) Dia. thru 2 places

7.13 (.281) R.2 PLACES

15.8 (.62) R.2 PLACES

“H” Dia.2 PLACES

14.27(.56) R.6 PLACES

“F” Dia. thru2 PLACES

14.27 (.562) Dia.Thru 4 PLACES

57.25(2.254)

DC A

A

A A

B B

E

E

G

Pumpseries

G20,G2020,GT20

G30,G3020,G3030,GT30

2-Bolt/4-Boltcombination flange

SAE “B”

SAE “C”

A

44.91(1.768)

57.25(2.254)

B

87.38(3.44)

90.48(3.56)

C

54.61(2.15)

67.30(2.65)

D

59.18(2.33)

72.90(2.87)

E

12.7(.50)

15.5(.61)

F

14.27(.562)

17.48(.688)

G

52.02(2.048)

65.99(2.598)

H

19.05(.750)

19.94(.785)

J101.60101.54(4.000)(3.998)

127.00126.95(5.000)(4.998)

K

9.40(.370)

12.45(.490)

F20,F2020,FT20

F30,F3020,F3030,FT30

SAE

“A”

2-B

OLT

SAE

“C”

4-B

OLT

SAE

2/4-

BO

LT


DRIVE SHAFTS

SAE “B” STRAIGHT KEYShaft No. 1: For F20, F2020 & FT20 Pumps292.6 Nm (2590 in. lb.) torsional capacity.*

SAE “C” STRAIGHT KEYShaft No. 1: For F30, F3020, F3030 & FT30 Pumps720.8 Nm (6380 in. lb.) torsional capacity.*

SAE “B” INVOLUTE SPLINEShaft No. 12: For F20, F2020 & FT20 Pumps279.6 Nm (2475 in. lb.) torsional capacity.*

SAE “C” INVOLUTE SPLINEShaft No. 12: For F30, F3020, F3030 & FT30 Pumps819.1 Nm (7250 in. lb.) torsional capacity.*

SAE “B-B” INVOLUTE SPLINEShaft No. 99: For F20, F2020 & FT20 Pumps451.9 Nm (4000 in. lb.) torsional capacity.*

* Applies to coaxial applications only. Consult representative if application requires greater capacityor has side loads.

For shaft options not shown, contact factory for specific shaft information.

Flat Root - Side FitNo. of Teeth - 13Diametral Pitch - 16/32Pressure Angle - 30°



39

41.15(1.62)

33.32(1.312)

26.97 Full(1.062) depth

6.356 (.250) Sq. x25.40 (1.00) long key

25.07 (.987)24.82 (.977)

.76 (.030)

.51 (.020) R.

22.22 (.875)22.20 (.874) Dia.

47.63(1.875)

33.02 Full depth(1.300) of keyway

7.93 (.312) Sq. x31.75 (1.25) long key

35.31 (1.390)35.06 (1.380)

31.75 (1.250)31.70 (1.240)D.

.76 (.030) R.55.5

(2.185)

55.5(2.185)

47.63(1.875)

31.24(1.23)

2.29(.09)x 45°

41.15(1.62)

12.7(.50)

1.52(.060)x 45°

1.52 (.06)2.29 (.09) R.

33.32(1.312)

45.97(1.81)

38.10(1.500)12.7(.500)


Rear Mounting Flanges for Thru-Drive Pumps

SAE “A” 2-Bolt

SAE “C” 2-Bolt/4-Bolt Combination for FT30 only

40

.375-16 UNC-2B THD.22.4 (.88) DEEP2 HOLES

COUPLING & MOUNTINGHOLES IN THIS POSITIONFOR COUNTERCLOCKWISE(L.H.) ROTATION

44.45(1.750) (REF.)

53.19(2.094)

59.18(2.33)

87.38(3.44)

53.19(2.094)

59.18(2.33)

87.38(3.44)

59.18(2.33)

103.63(4.08)

82.5882.63(3.251)(3.475)

DIA.

88.0188.27(3.465)(3.475)

DIA.

2.05 (.081)2.16 (.085)

11.43 (.45).381 (.015) R

.76 (.030) R(MAX.)

1.875 (MAX.)

CUSTOMERSHAFT

.500-13 UNC-2B THD.26.9 (1.06) DEEP4 PLACES

COUPLING & MOUNTINGHOLES IN THIS POSITIONFOR COUNTERCLOCKWISEROTATION

.625-11 UNC-2B THD.26.9 (1.06) DEEP2 PLACES

73.15(2.88)

73.15(2.88)

127.25(5.01)

73.91(2.91)

57.25(2.254)

57.25(2.254)

57.25(2.254)

57.25(2.254)

90.48(3.562)

90.48(3.562)

106.2(4.18)

106.2(4.18)

127.03127.08(5.001)(5.003)

DIA.

132.46132.72(5.215)(5.225)

DIA.

2.05 (.081)2.16 (.085)

.76 (.030) R. 57.15(2.250)

.127 (.005)

.381 (.015)

1.875 (MAX.)

16.76 (.66)

R.

MAX.

CUSTOMER SHAFTEXTENSION

4-Bolt Flange Port ConnectionsPort size

(model codedesignation)

A

B

C

D

E

F

G

Dimensions - mm (inch)

H

19.05(.750)25.40(1.000)31.75(1.250)38.10(1.500)50.80(2.000)63.50(2.500)76.20(3.000)

J

11.13(.438)13.09(.515)15.09(.594)17.86(.703)21.44(.844)25.40(1.000)30.96(1.219)

K

22.22(.875)26.19(1.031)30.18(1.199)35.71(1.406)42.87(1.688)50.80(2.000)61.93(2.438)

L

23.82(.938)26.19(1.031)29.36(1.156)34.93(1.375)38.89(1.531)44.45(1.750)53.19(2.094)

M

47.62(1.875)52.37(2.062)58.72(2.312)69.85(2.750)77.77(3.062)88.90(3.500)106.38(4.188)

N

(.375-16)

(.375-16)

(.438-14)

(.500-13)

(.500-13)

(.500-13)

(.625-11)

P

22.35(.88)

22.35(.88)

25.40(1.00)25.40(1.00)25.40(1.00)30.23(1.19)30.23(1.19)

“N” UNC-2B THD.“P” DEEP4 PLACES

J

M

“H” D.

L

K


Rear Couplings for Thru-Drive Pumps

Coupling Spline Data - mm (inches)

Internal Involute Spline Flat Root - Side FitNo. of Teeth - 9Diametral Pitch - 16/32Pressure Angle - 30°


Internal Involute SplinelFlat Root - Side FitNo. of Teeth - 13Diametral Pitch - 16/32Pressure Angle - 30°





The customer shaft extension must conform, in all respects, to SAE J744 “Hydraulic Pump Mounting & Drive Dimensions” standards as theyapply to external splines.

13.72 (.54)11.30 (.445)12.93 (.509)

39.68(1.562) Dia.

.76 (.030) R.

13.72 (.54)11.30 (.445)12.93 (.509)

39.68(1.562) Dia.

.76 (.030) R.

13.72 (.54)11.30 (.445)12.93 (.509)

39.68(1.562) Dia.

.76 (.030) R.

16.76 (.66) (Ref.)

11.76 (.463)13.49 (.531)Coupling FromMounting Face

48.41(1.906) Dia.

.76 (.030) R.

SAE “A” SIZE COUPLING

SAE “B” SIZE COUPLING

SAE “B-B” SIZE COUPLING

SAE “C” SIZE COUPLING

41


Technical Performance Data F20 & F30 Pumps42

F

F

43

GC Series Hydraulic PumpsCompact cast iron gear pumps with a wide variety ofintegrated options provide custom systems capability andhigh-effifiency performance. Displacements from 0.065 to0.711 cu. in. (1.066 to 11.65 cc) per revolution. Pressures to 4,000psi (275 bar).

D Series Hydraulic PumpsCompact, external gear pumps for use in pumping fluids with lubri-cating qualities. Suitable for use in a wide variety of applications,including agricultural, construction, transmission charge and lube,and diesel fuel transfer. Displacements from .232 cu. in. to 1.395cu. in. (3.8 - 22.9 cc) per revolution. Pressures to 3,000 psi (207bar).

H Series Hydraulic PumpsCast iron, external gear pumps for use in pumping fluids with lubri-cating qualities. Designed to provide reliable, long-life service under rugged conditions. Suitable for use in a wide varietyof applications, including agricultural, construction, transmissioncharge and lube, and diesel fuel transfer. Displacements from 0.60cu. in. to 2.40 cu. in. (9.8 - 39.4 cc) per revolution. Pressures to3,000 psi (207 bar).

W Series Gear PumpsHighly efficient pumps feature 4,000 psi continuousoperation, speed range from 500 to 4,000 rpm, low noiseoperation and overall efficiency greater than 90%.Displacements from .03 to 3.05 cu. in. (.5 to 50 cc) perrevolution. Other features include SAE, ISO and DIN shafts, flangesand ports; integrated valves and multiple pump configurations.

F20LS/F30LS Load Sense Variable Discharge Gear PumpsOffers the horsepower conservation of a load sense system and the low cost reliability of a gear pump. Featuring castiron construction and 4,000 psi continuous operation for severe-duty applications. Displacements from 1.41 to 9.82 cu. in. (23 to161 cc).

F20 & F30 Series Gear PumpsRugged cast iron pumps offer high performance for severe-dutyapplications. Available in single, multiple and through-drive versions.Displacements from 1.41 to 9.82 cu. in. (23 to161 cc) per revolu-tion. Pressures to 4,000 psi (275 Bar) continuous.

F20 / F30 Specialty Products• F20 / F30 PTO Pump Series. Specifically designed pump options

and features for PTO (power take off) applications. Displacementsfrom 1.41 to 9.82 cu. in. (23 to 161 cc).

• F20 / F30 two section flow dividers. Displacements from 1.41to 9.82 cu. in. (23 to 161 cc) per section. Pressures to 4,000 psicontinuous (275 Bar).

Gerotor PumpsHigh-efficiency, low-maintenance design with quiet operation and uniform flow. Extremely tolerant of contamination. Displacements from 0.05 to 8.29 cu. in. (0.8 to135.8 cc) per revolution. Pressures to 2,000 psi (136 Bar).

GC-9500 AC Hydraulic Power UnitsAC power units offering the ultimate in design versatility andordering flexibility. It can be ordered completely assembled or inkits. Standard options include: motors (1/2-5 hp, TEFC, open, anddrip-proof); 4 reservoirs (5,10, 15 and 20 gal.); and pumps (pres-sure balanced and high/low with flows to 28 gpm and pressures to3500 psi).

HE Power Packs (AC & DC Hydraulic Power Packs)Self-contained modular power systems in fully assembled orkit form; wide range of standard or high efficiency pumps, motors,switches, mounts, valves, and reservoirs. Custom options also avail-able. Pressures to 4,000 psi (276 Bar). Flows from 0.20 to 7.0GPM.

Hydraulic MotorsAvailable in the GC, W and F20 Series in unidirectional andbirotational configurations. Motors available with modularvalve, bearing, seal and shaft options for maximum flexibility.Displacements from 0.065 to 5.30 cu. in. (1.06 to 87.0 cc) per rev-olution. Pressures to 4,000 psi (275 Bar).

Two-Stage Hydraulic PumpsExternal gear pumps designed for high-speed positioningcoupled with maximum working pressure. High-pressuredisplacements from 0.258 to 1.395 cu. in. (4.23 to 22.86 cc) perrevolution. Pressures to 4,000 psi (275 Bar). Flows from 5 to 28GPM.

Rotary Flow DividersRotary-gear units up to four sections for synchronizedoperation of multiple cylinders or motors, proportionaldivision of output or intensified flow. Single-sectiondisplacements from 0.065 to 0.813 cu. in. (1.0 to 13.32 cc)per revolution. Pressures to 4,500 psi (306 Bar).

Call us for more informationFor application assistance or detailed literature on anyHaldex product line, call us toll-free: 1-800-572-7867.Visit our web site: http://www.haldex.comE-mail us: [email protected] [email protected]

Only Haldex offers this extensive rangeof pumps, hydraulic motors, powerpacks and flow dividers, worldwide.

Haldex (www.haldex.com),headquartered in Stockholm,Sweden, is a provider of

proprietary and innovative solutions to theglobal vehicle industry, with focus on products in vehicles that enhance safety,environment and vehicle dynamics. Haldex islisted on the Nasdaq OMX StockholmStock Exchange and had net sales ofnearly 8.5 billion SEK in 2008. The numberof employees amounts to about 5,000. The right to modification for technical improvements is reserved.

HA

LEX

-F20

/F30

PM

P-U

SA-2

009-

12

PRODUCT RANGE

He Power Packs12/24/48 VDC 0.8 - 3.5 kW and 0.75- 3 kW AC modular power packs

Pressure Switches5 - 350 bar connecting /disconnecting

He Classic Power Packs12/24/48 VDC modular powerpacks in weatherproof boxes

W100 Hydraulic Pumps0.5 - 2.0 cc/section, 227 bar

W300 Hydraulic Pumps0.8 - 5.7 cc/section, 230 bar

W600 Hydraulic Pumps4 - 12 cc/section, 276 bar

WM600 Hydraulic Motors4 - 12 cc/section, 276 bar



WQ900 The Quiet Pump5 - 27 cc/section, 230 bar




G25 Hydraulic Pumps23 - 87 cc/section, 250 bar

GM25 Hydraulic Motors23 - 87 cc/section, 250 bar

GPA Internal Gear Pumps1.7 - 63 cc/section, 100 bar

GC Hydraulic Pumps/Fluid Motors1.06 - 11.65 cc/section, 276 bar

II-Stage Hydraulic Pumps4.2 - 22.8 cc/section, 276 bar

Rotary Flow Dividers3.8 - 13.3 cc/section, 300 bar

D Hydraulic Pumps3.8 - 22.9 cc/section, 207 bar

H Hydraulic Pumps9.8 - 39.4 cc/section, 207 bar

F12 Hydraulic Pumps16 - 41 cc/section, 276 bar

F15 Hydraulic Pumps19 - 50 cc/section, 276 bar

F20/F30 Hydraulic Pumps23 - 161 cc/section, 276 bar

FM20/FM30 Hydraulic Motors23 - 161 cc/section, 276 bar

F20LS/F30LS Hydraulic Pumps23 - 161 cc/section, 276 bar

Transmission Pumps

www.haldex.com/hbus

Haldex Hydraulics Corp.2222 15th StreetROCKFORD, IL 61104USATel: +1-815 398 4400Fax: +1-815 398 5977E-mail: [email protected]

Haldex Hydraulics Corp.214 James Farm RoadSTATESVILLE, NC 28625USATel: +1-704 873 2587Fax: +1-704 878 0530E-mail: [email protected]

Haldex Hydraulics ABRingvägen 3, Box 95SE-280 40 SK. FAGERHULTSwedenTel: +46-433 32400Fax: +46-433 30546E-mail: [email protected]

Haldex Hydraulics ABNymärsta Gränd 6, Box 511SE-195 25 MÄRSTASwedenTel: +46-8 591 288 50Fax: +46-8 591 288 60E-mail: [email protected]

Haldex Hydraulics GmbHSeligenweg 12, Postfach 1507D-95014 HOFGermanyTel: +49-9281 895-0Fax: +49-9281 87133E-mail: [email protected]

Haldex International Trading (Shanghai) Co. Ltd.16 A, Zhao Feng World Trade BuildingNo. 369 Jiang Su RoadCN-200050 SHANGHAIChinaTel: +86 21 5240 0338Fax: +86 21 5240 0177E-mail: [email protected]

Haldex Vehicle Products (Suzhou) Co., Ltd.LongPu Road No.6Suzhou Industrial ParkSUZHOU 215126P. R. ChinaTel: +86 512 8885 5301Fax: +86 512 8765 6066

Haldex Hydraulics (Qingzhou) Co. Ltd.No.1789, Shidai Yi RoadEconomy Development ZoneQINGZHOU 262500P. R. ChinaTel: +86 536 3296 598Fax: +86 536 3296 410

Documents

F20/F30 Ferra Series Hydraulic Pumps