Upload
others
View
9
Download
0
Embed Size (px)
Citation preview
www.Fisher.com
Fisher™ EWD, EWS, and EWT Valves through NPS 12x8
ContentsIntroduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scope of Manual 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Description 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Specifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Educational Services 4. . . . . . . . . . . . . . . . . . . . . . . . .
Installation 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inverted Globe Valve Applications
(Actuator below valve) 6. . . . . . . . . . . . . . . . . . . . .Maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packing Lubrication 8. . . . . . . . . . . . . . . . . . . . . . . . . .Packing Maintenance 10. . . . . . . . . . . . . . . . . . . . . . . .
Replacing Packing 11. . . . . . . . . . . . . . . . . . . . . . .Trim Maintenance 14. . . . . . . . . . . . . . . . . . . . . . . . . .
Trim Removal 15. . . . . . . . . . . . . . . . . . . . . . . . . .Lapping Metal Seats 16. . . . . . . . . . . . . . . . . . . . .Valve Plug Maintenance 17. . . . . . . . . . . . . . . . . .Trim Replacement 19. . . . . . . . . . . . . . . . . . . . . .
Retrofit: Installing C‐seal Trim 20. . . . . . . . . . . . . . . .Replacement of Installed C‐seal Trim 24. . . . . . . . . . .
Trim Removal (C‐seal Constructions) 24. . . . . . .Lapping Metal Seats (C‐seal Constructions) 25. .Remachining Metal Seats
(C‐seal Constructions) 25. . . . . . . . . . . . . . . . .Trim Replacement (C‐seal Constructions) 26. . .
ENVIRO‐SEAL� Bellows Seal Bonnet 27. . . . . . . . . . .Parts Ordering 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Parts Kits 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Parts List 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1. Fisher NPS 12x6 EW Series Valve With 667 Actuator
W2777‐2*
Introduction
Scope of ManualThis instruction manual includes installation, maintenance, and parts information for Fisher NPS 4x2 through 12x8EWD, EWS, and EWT valves (figure 1). Refer to separate manuals for instructions covering the actuator andaccessories.
Do not install, operate, or maintain an EW valve without being fully trained and qualified in valve, actuator, andaccessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important tocarefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If youhave any questions about these instructions, contact your Emerson sales office or Local Business Partner beforeproceeding.
Instruction ManualD100399X012
EW ValveJuly 2017
Instruction ManualD100399X012
EW ValveJuly 2017
2
Table 1. Specifications
End Connection Styles
Flanged Ends: CL300, CL600, or CL900 Raised‐face orring‐type joint flanges per ASME B16.5
Buttwelding Ends: Styles per ASME B16.25 schedulesconsistent with ASME B16.34 are: Schedules � 40 or� 80 for all CL300 and CL600 valves, Schedule � 80or � XXS for NPS 8x6 CL900 valves, or Schedule� 80, � 100, or � 120 for NPS 12x8 CL900 valves.
Maximum Inlet Pressures, Temperatures, andPressure Drops(1)
Consistent with applicable � CL300, � CL600(2), or� CL900(3) pressure/temperature ratings per ASMEB16.34, but do not exceed the pressure,temperature, and pressure drop conditions specifiedwhen the valve was ordered. Also see the Installationsection.
Also see Bulletin 80.3:010 WhisperFlo� AerodynamicAttenuation Trims, D102362X012
Shutoff Classifications
See table 2C‐seal trim: High‐temperature, Class V per ANSI/FCI70‐2 and IEC 60534‐4 See table 3WhisperFlo Trim: � Class IV per ANSI/FCI 70‐2 and IEC 60534‐4� Others per application
Flow Characteristics
Standard Cages: � Linear, � quick opening, or� equal percentageWhisper Trim� and Cavitrol� Cages: LinearWhisperFlo Trim: Linear (restricted linear cages andspecial, characterized cages are available--consultyour Emerson sales office or Local Business Partner)
Flow Directions
EWS and Standard Cage: Normally upEWD or EWT with Standard Cage: Normally down
Whisper Trim Cages: Always upCavitrol Cages: Always downWhisperFlo Trim: Flow up (standard)—through theseat ring and out through the cage orifices
Approximate Weights
See table 4
WhisperFlo Trim Material and Selection
� 410 Stainless Steel� Others per applicationSee appropriate valve body bulletin
WhisperFlo Pressure/Temperature Capability
� -29 to 427�C (-20 to 800�F)� Others per applicationSee appropriate valve body bulletin forcomplementary information
WhisperFlo Aerodynamic Trim Pressure Ratings(1,2)
Up to 1500 psi drop
WhisperFlo Velocity Limits
WhisperFlo trim is designed for 0.3 MACH as aninherent outlet velocity limit. Variations higher andlower may be applied per special applications
WhisperFlo Rangeability
100:1
WhisperFlo Noise Attenuation
Approximately -40 dBA maximum depending on the�P/P1 ratio per IEC 534‐8‐3 calculation procedureSee Fisher Specification Manager
Additional Specifications
For specifications such as materials, port diameters,valve plug travels, yoke boss diameters, and stemdiameters, refer to the Parts List
1. The pressure or temperature limits in this manual and any applicable standard limitations should not be exceeded.2. Certain bonnet bolting material selections may require a CL600 easy‐e valve assembly to be derated. Contact your Emerson sales office.3. There are two different CL900 NPS 8x6 valve bodies, one for use only with Cavitrol III cages and the other for use with all other constructions. A CL900 valve with Cavitrol III cage can take fullCL900 pressure drops. For information on other NPS 8x6 constructions that can take full CL900 pressure drops, contact your Emerson sales office. All other trim constructions are limited toCL600 pressure/temperature limits even though installed in a CL900 valve.
Instruction ManualD100399X012
EW ValveJuly 2017
3
Figure 2. Cutaway Detail of the Fisher WhisperFlo Trim, Valve Body Typical
W6825‐1
DescriptionThese single‐port globe‐style valves have cage guiding, clamped seat rings, and push‐down‐to‐close valve plug action.Valve configurations are as follows:
EWD: Balanced valve plug with metal‐to‐metal seating for all general applications over a wide range of pressure dropsand temperatures.
C‐seal trim is available for EWD valves, CL300 and CL600, in sizes NPS 6x4x2‐1/2, 6x4, 8x4, 8x6, 12x6, 10x8, and 12x8.
With C‐seal trim, a balanced valve can achieve high‐temperature, Class V shutoff. Because the C‐seal plug seal isformed from metal (N07718 nickel alloy) rather than an elastomer, a valve equipped with the C‐seal trim can beapplied in processes with a fluid temperature of up to 593�C (1100�F), provided other material limits are notexceeded.
EWS: Unbalanced valve plug with metal‐to‐metal or optional metal‐to‐PTFE seating for all general applicationsrequiring better shutoff capabilities than can be obtained with the EWD valve.
EWT: Balanced valve plug with either metal‐to‐PTFE seating (standard for all except Cavitrol III cages) for stringentshutoff requirements or metal‐to‐metal seating (standard for Cavitrol III cages, optional for all others) for highertemperatures.
Control valves with WhisperFlo cages (figure 2) provide additional attenuation for aerodynamic noise in verydemanding vapor or gas applications with high‐pressure drops. A WhisperFlo cage with an appropriately sized valvebody is designed to reduce the noise level up to -40 dBA. For special applications, -50 dBA attenuation can beachieved.
SpecificationsTypical specifications for these valves are shown in table 1.
Instruction ManualD100399X012
EW ValveJuly 2017
4
Table 2. Shutoff Classification Per ANSI/FCI 70‐2 and IEC 60534‐4Valve Seating Shutoff Class
EWD Metal II (standard)
III (optional for NPS 6x4 through 12x6 valves with optional single graphite piston ring or for NPS 10x8 and 12x8 valves with optional double piston rings)
IV (optional for NPS 6x4 through 12x8 valves with optional multiple graphite piston rings)
EWS Metal IV (standard)
V (optional, consult your Emerson sales office or Local Business Partner)
EWS PTFE VI
EWT with all exceptCavitrol III cages
PTFE Standard Air Test (maximum leakage is 0.05 mL/min/psid/inch port diameter)
V (optional)
Metal IV (standard)
Metal V (optional)(1)
EWT with1‐stage Cavitrol III cage
Metal IV (standard)
V (optional)
EWT with 2‐stage Cavitrol III cage Metal V
1. Class V shutoff for EWT requires spring loaded seal ring, radius‐seat plug, wide‐bevel seat ring, and seat lapping. Not available with 8‐inch port, quick‐opening cage. Not available withS31600 (316 SST) valve plug and seat ring.
Table 3. Additional Shutoff Classification for C‐seal Trim Per ANSI/FCI 70‐2 and IEC 60534‐4Valve Valve Size, NPS Port Diameter, Inches Cage Style Leakage Class
EWD(CL300, CL600)
6x4x2‐1/2 2.875Equal Percentage, Linear, Whisper I,
Cavitrol III (2‐stage)
V (for portdiameters from 2.875 through 8‐inch withoptional C‐seal trim)
6x48x4
4.375Equal Percentage, Linear, Whisper I,
Cavitrol III (1‐stage)
8x6 and 12x6 5.375 Whisper III (A3, B3, D3, D3), Cavitrol III (2‐stage)
8x612x6
7Equal Percentage, Linear, Whisper I,
Cavitrol III (1‐stage)
10x812x8
8Equal Percentage, Linear, Whisper I,
Cavitrol III (1‐stage)
Educational ServicesFor information on available courses for the Fisher EW valve, as well as a variety of other products, contact:
Emerson Automation SolutionsEducational Services - RegistrationPhone: 1-641-754-3771 or 1-800-338-8158E-mail: [email protected]/fishervalvetraining
Installation
WARNING
Always wear protective gloves, clothing, and eyewear when performing any installation operations to avoid personalinjury.
Personal injury or equipment damage caused by sudden release of pressure or bursting of parts may result if the valveassembly is installed where service conditions could exceed the limits given in table 1 or on the appropriate nameplates. Toavoid such injury or damage, provide a relief valve for overpressure protection as required by government or acceptedindustry codes and good engineering practices.
Instruction ManualD100399X012
EW ValveJuly 2017
5
Check with your process or safety engineer for any additional measures that must be taken to protect against processmedia.
If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in thisinstruction manual.
CAUTION
When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature,pressure drop and controlled fluid conditions. Responsibility for the safety of process media and compatibility of valvematerials with process media rests solely with the purchaser and end‐user. Since some body/trim material combinationsare limited in their pressure drop and temperature ranges, do not apply any other conditions to the valve without firstcontacting your Emerson sales office or Local Business Partner.
Before installing the valve, inspect the valve and pipelines for any damage and any foreign material which may causeproduct damage.
Table 4. Approximate Weights
END CONNECTION
VALVE SIZE, NPS
4X2 6X4 8X4 8X6 10X8 12X6 12X8
Kg Lb Kg Lb Kg Lb Kg Lb Kg Lb Kg Lb Kg Lb
CL300 (flanged only) 84 185 150 330 234 515 284 625 567 1250 500 1102 653 1440
CL600Flanged 100 220 195 430 272 600 308 680 744 1640 721 1590 857 1890
Buttwelding 61 135 122 270 177 390 272 600 512 1130 526 1160 658 1450
CL900Flanged ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ 612 1350 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ 1361 3000
Buttwelding ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ 454 1000 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ 1293 2850
CAUTION
If hoisting the valve, use a nylon sling to protect the surfaces. Carefully position the sling to prevent damage to the actuatortubing and any accessories. Also, take care to prevent people from being injured in case the hoist or rigging slipsunexpectedly. Refer to table 4 for valve assembly weights. Be sure to use adequately sized hoists and chains or slings tohandle the valve.
1. Before installing the valve, inspect the valve body cavity and associated equipment for any damage and any foreignmaterial.
2. Make certain the valve body interior is clean, that pipelines are free of foreign material, and that the valve isoriented so that pipeline flow is in the same direction as the arrow on the side of the valve.
3. Install the control valve assembly in any orientation unless limited by seismic criteria. However, the normal methodis with the actuator vertical above the valve. Other positions may result in uneven valve plug and cage wear and inimproper operation. With some valves, the actuator may also need to be supported when it is not vertical. For moreinformation, consult your Emerson sales office or Local Business Partner.
Note
If installing a valve with small internal flow passages, such as with WhisperFlo, Whisper Trim, or Cavitrol cages, consider installingan upstream strainer to prevent the lodging of particles in these passages. This is especially important if the pipeline cannot bethoroughly cleaned or if the flowing medium is not clean.
Instruction ManualD100399X012
EW ValveJuly 2017
6
4. Use accepted piping and welding practices when installing the valve in the line. For flanged valve bodies, use asuitable gasket between the valve body and pipeline flanges.
CAUTION
Depending on valve body materials used, post weld heat treating may be required. If so, damage to internal elastomericand plastic parts, as well as internal metal parts is possible. Shrink‐fit pieces and threaded connections may also loosen. Ingeneral, if post weld heat treating is to be performed, remove all trim parts. Contact your Emerson sales office or LocalBusiness Partner for additional information.
5. With a leak‐off bonnet construction, remove the pipe plugs (keys 14 and 16, figure 21) from the bonnet to hook upthe leak‐off piping. If continuous operation is required during inspection or maintenance, install a three‐valvebypass around the control valve assembly.
6. If the actuator and valve are shipped separately, refer to the actuator mounting procedure in the appropriateactuator instruction manual.
WARNING
Personal injury could result from packing leakage. Valve packing was tightened before shipment; however, the packingmight require some readjustment to meet specific service conditions. Check with your process or safety engineer for anyadditional measures that must be taken to protect against process media.
Valves with ENVIRO‐SEAL live‐loaded packing or HIGH‐SEAL live‐loaded packing will not require this initialre‐adjustment. See Fisher instruction manuals, ENVIRO‐SEAL Packing System for Sliding‐Stem Valves, D101642X012,or HIGH‐SEAL Live‐Loaded Packing System, D101453X012, (as appropriate), for packing instructions. If you wish toconvert your present packing arrangement to ENVIRO‐SEAL packing, refer to the retrofit kits listed in the parts kitsub‐section near the end of this manual.
Inverted Globe Valve Applications (Actuator below valve)Due to space restrictions in your application, you may be required to mount the valve/actuator assembly in an invertedorientation, with the actuator positioned below the valve. If so, the following procedures will help you withdisassembly and assembly techniques.
WARNING
Avoid personal injury or property damage caused by components dropping.
With the valve/actuator upside down, components may drop during disassembly or assembly. Be careful not to positionyourself below the valve in the path of falling parts.
As the bonnet/plug/cage is lowered from the valve body, the center of gravity will be above the lifting points. Take care toprevent the assembly from tipping over as it is lowered. Either leave the actuator attached to the plug and bonnet, attachstraps to the stem, or provide other means to prevent tipping.
Disassembly1. Provide adequate support to the actuator while removing it from the bonnet.
Instruction ManualD100399X012
EW ValveJuly 2017
7
2. Provide adequate support to the bonnet while removing the bonnet nuts.
3. Be aware that the bonnet/plug/cage may tip over as they are lowered from the valve body. Make provision toprevent tipping.
4. Be aware that the cage and seat ring may not come out with the bonnet and plug/stem assembly. If this occurs,make provision to support these parts, as they may fall out unexpectedly.
Assembly1. Start this assembly procedure with the plug/stem assembly already installed in the bonnet.
2. Put the gaskets and cage onto the bonnet and plug.
3. Place the seat ring with the seat ring gasket onto the cage, if applicable with the valve design.
4. Raise this bonnet/plug/cage assembly up into the valve body. Make provision to prevent tipping of these parts asthey are being raised into the valve body.
5. Torque the bonnet nuts.
6. Mount the actuator.
MaintenanceValve parts are subject to normal wear and must be inspected and replaced as necessary. Inspection and maintenancefrequency depends on the severity of service conditions. This section includes instructions for packing lubrication,packing maintenance, trim maintenance, lapping metal seats, and ENVIRO‐SEAL bellows seal bonnet replacement. Allmaintenance operations may be performed with the valve in the line.
WARNING
Avoid personal injury or property damage from sudden release of process pressure. Before performing any maintenanceoperations:
� Do not remove the actuator from the valve while the valve is still pressurized.
� Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personalinjury.
� Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure theactuator cannot suddenly open or close the valve.
� Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressureon both sides of the valve. Drain the process media from both sides of the valve.
� Vent the pneumatic actuator loading pressure and relieve any actuator spring precompression.
� Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.
� The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from thepipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or whenloosening the packing box pipe plug.
� Check with your process or safety engineer for any additional measures that must be taken to protect against processmedia.
CAUTION
Follow instructions carefully to avoid damaging the product surfaces, which could result in damage to the product.
Instruction ManualD100399X012
EW ValveJuly 2017
8
Note
Whenever a gasket seal is disturbed by removing or shifting gasketed parts, install a new gasket upon reassembly. This is necessaryto ensure a good gasket seal because the used gasket may not seal properly.
Figure 3. Lubricator and Lubricator/Isolating Valve (optional)
LUBRICATOR
LUBRICATOR/ISOLATING VALVE10A9421‐AAJ5428‐DA0832‐2
Packing Lubrication
CAUTION
Do not lubricate graphite packing. Graphite packing is self-lubricated. Additional lubrication may result in slip-stickmovement of the valve.
Note
ENVIRO‐SEAL or HIGH‐SEAL packing does not require lubrication.
WARNING
To avoid personal injury or property damage resulting from fire or explosion, do not lubricate packing used in oxygenservice or in processes with temperatures over 260�C (500�F).
If a lubricator or lubricator/isolating valve (figure 3) is provided for PTFE/composition or other packings that requirelubrication, it will be installed in place of the pipe plug (key 14, figure 21). Use a good quality silicon‐base lubricant. Donot lubricate packing used in oxygen service or in processes with temperatures over 260�C (500�F). To operate thelubricator, simply turn the cap screw clockwise to force the lubricant into the packing box. The lubricator/isolatingvalve operates the same way, except open the isolating valve before turning the cap screw and then close the isolatingvalve after lubrication is completed.
Instruction ManualD100399X012
EW ValveJuly 2017
9
Figure 4. PTFE V‐Ring Packing Arrangements
UPPER WIPER(KEY 12)
PACKING FOLLOWER(KEY 13)
WASHER(KEY 10)
SPRING(KEY 8)
PACKING BOXRING (KEY 11)
FEMALEADAPTOR
PACKING RING
MALEADAPTOR
LOWER WIPER
FEMALEADAPTOR
PACKING RING
MALEADAPTOR
LOWER WIPER
UPPER WIPER(KEY 12)
PACKING FOLLOWER(KEY 13)
SPACER(KEY 8)
PACKING BOXRING (KEY 11)
11
FOR S31600 (316 SST) ORS17400 (17‐4PH SST)
METAL PACKING BOX PARTS
FOR ALL OTHER METAL PACKINGBOX PART MATERIALS
SINGLE ARRANGEMENTS
NOTE:PACKING SET (KEY 6) (2 REQ'D FOR DOUBLE ARRANGEMENTS).
12A7837−A/IL
B2398
1
1
1
1
1
1
1
UPPER WIPER(KEY 12)
PACKING FOLLOWER (KEY 13)
LANTERN RING(KEY 8)
PACKING BOXRING (KEY 11)
MALE ADAPTOR
PACKING RING
FEMALE ADAPTOR
LOWER WIPERASSEMBLY 1(POSITIVE
PRESSURES)
ASSEMBLY 2(VACUUM)
ASSEMBLY 3(POSITIVE
PRESSURES& VACUUM)
ASSEMBLY 1(POSITIVE
PRESSURES)
ASSEMBLY 2(VACUUM)
ASSEMBLY 3(POSITIVE
PRESSURES& VACUUM)
ASSEMBLY 1(POSITIVE
PRESSURES)
ASSEMBLY 2(VACUUM)
ASSEMBLY 3(POSITIVE
PRESSURES& VACUUM)
9.5 mm (3/8 INCH) STEM 12.7 mm (1/2 INCH) STEM 19.1, 25.4, OR 31.8 mm(3/4, 1, OR 1‐1/4 INCH) STEM
DOUBLE ARRANGEMENTS
12A8187-C 12A7814-C 12A7839-A
B1428‐2
Instruction ManualD100399X012
EW ValveJuly 2017
10
Packing Maintenance
Note
For valves with ENVIRO‐SEAL live‐loaded packing, see the Fisher instruction manual, ENVIRO‐SEAL Packing System for Sliding‐StemValves, D101642X012, for packing instructions. For valves with HIGH‐SEAL live‐loaded packing, see the Fisher instruction manual,HIGH‐SEAL Live‐Loaded Packing System, D101453X012, for packing instructions.
Key numbers refer to figure 4 for PTFE V‐ring packing and to figure 5 for PTFE/composition packing, unless otherwiseindicated.
For spring‐loaded single PTFE V‐ring packing, the spring (key 8, figure 4) maintains a sealing force on the packing. Ifleakage is noted around the packing follower (key 13, figure 4), check to be sure the shoulder on the packing followeris touching the bonnet. If the shoulder is not touching the bonnet, tighten the packing flange nuts (key 5, figure 21)until the shoulder is against the bonnet. If leakage cannot be stopped in this manner, go to the Replacing Packingprocedure.
Figure 5. Detail of PTFE/Composition Packing Arrangements
UPPER WIPER(KEY 12)
PACKING FOLLOWER(KEY 13)
LANTERN RING(KEY 8)
PACKING BOXRING (KEY 11)
PACKING RING(KEY 7)
9.5 mm(3/8 INCH)
STEM
12.7 mm(1/2 INCH)
STEM
19.1, 25.4, OR31.8 mm
(3/4, 1, OR1‐1/4 INCH) STEM
TYPICAL (DOUBLE) ARRANGEMENTS
12A8188‐A12A7815‐A12A8173‐AA2619‐1
If there is undesirable packing leakage with other than spring‐loaded packing, first try to limit the leakage andestablish a stem seal by tightening the packing flange nuts.
If the packing is relatively new and tight on the stem and if tightening the packing flange nuts does not stop theleakage, the valve stem may be worn or nicked so that a seal cannot be made. The surface finish of a new valve stem iscritical for making a good packing seal. If the leakage comes from the outside diameter of the packing, the leakagemay be caused by nicks or scratches around the packing box wall. If performing any of the following procedures,inspect the valve stem and packing box wall for nicks and scratches.
Replacing Packing
WARNING
Avoid personal injury or property damage from sudden release of process pressure. Before performing any maintenanceoperations:
Instruction ManualD100399X012
EW ValveJuly 2017
11
� Do not remove the actuator from the valve while the valve is still pressurized.
� Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personalinjury.
� Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure theactuator cannot suddenly open or close the valve.
� Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressureon both sides of the valve. Drain the process media from both sides of the valve.
� Vent the pneumatic actuator loading pressure and relieve any actuator spring precompression.
� Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.
� The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from thepipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or whenloosening the packing box pipe plug.
� Check with your process or safety engineer for any additional measures that must be taken to protect against processmedia.
1. Isolate the control valve from the line pressure, release pressure from both sides of the valve, and drain the processmedia from both sides of the valve. If using a power actuator, also shut‐off all pressure lines to the power actuatorand release all pressure from the actuator. Use lock‐out procedures to be sure that the above measures stay ineffect while you work on the equipment.
2. Disconnect the operating lines from the actuator and any leak‐off piping from the bonnet. Disconnect the stemconnector, and then remove the actuator from the valve by unscrewing the yoke locknut (key 15, figure 21) or the
hex nuts (key 26, figure 21).
3. Loosen the packing flange nuts (key 5, figure 21) so that the packing is not tight on the valve stem. Remove anytravel indicator parts and stem locknuts from the valve stem threads.
WARNING
To avoid personal injury or property damage caused by uncontrolled movement of the bonnet, loosen the bonnet byfollowing the instructions in the next step. Do not remove a stuck bonnet by pulling on it with equipment that can stretchor store energy in any other manner. The sudden release of stored energy can cause uncontrolled movement of the bonnet.
Note
The following step also helps to provide additional assurance that the valve body fluid pressure has been relieved.
4. Hex nuts (key 16, figure 22, 23 or 24) attach the bonnet (key 1, figure 21) to the valve body (key 1, figure 22, 23 or24). Loosen these nuts approximately 3 mm (1/8 inch). Then loosen the body‐to‐bonnet gasketed joint by eitherrocking the bonnet or prying between the bonnet and valve body. Work the prying tool around the bonnet until thebonnet loosens. If no fluid leaks from the joint, proceed with bonnet removal as described in the following steps.
CAUTION
To avoid damage to the seating surface caused by the valve plug and stem assembly dropping from the bonnet after beinglifted part way out, temporarily install a valve stem locknut on the valve stem when lifting the bonnet. The locknutprevents the valve plug and stem assembly from dropping out of the bonnet.
5. Completely remove the hex nuts (key 16) and carefully lift the bonnet off the valve body.
Instruction ManualD100399X012
EW ValveJuly 2017
12
6. Remove the locknut and separate the valve plug and stem from the bonnet. Set the parts on a protective surface toprevent damage to gasket or seating surfaces.
7. Remove the bonnet gasket (key 10, figure 22 through 24), and cover the opening in the valve body to protect thegasket surface and prevent foreign material from getting into the valve body cavity.
8. Remove the packing flange nuts, packing flange, upper wiper, and packing follower (keys 5, 3, 12, and 13, figure21). Carefully push out all the remaining packing parts from the valve side of the bonnet using a rounded rod orother tool that will not scratch the packing box wall. Clean the packing box and the metal packing parts.
9. Inspect the valve stem threads and packing box surfaces for any sharp edges that might cut the packing. Scratchesor burrs could cause packing box leakage or damage to the new packing. If the surface condition cannot beimproved by light sanding, replace the damaged parts by following the appropriate steps in the Trim Maintenanceprocedure.
10. Remove the covering protecting the valve cavity and install a new bonnet gasket (key 10, figure 22 through 24),making sure the gasket seating surfaces are clean and smooth. Place the stem and valve plug into the valve bodyand slide the bonnet over the stem and onto the stud bolts (key 15, figure 22, 23, or 24).
Figure 6. Detail of Graphite Ribbon/Filament Packing
NOTES: 0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS;
USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING.
PACKINGFOLLOWER(KEY 13)
LANTERNRING (KEY 8)PACKING BOXRING (KEY 11)
1
12.7 mm(1/2 INCH)
STEM
SINGLE ARRANGEMENTS
A6067
GRAPHITERIBBONPACKING RING(KEY 7)
GRAPHITEFILAMENTPACKING RING(KEY 7)
1
19.1, 25.4, & 31.8 mm(3/4, 1 & 1‐1/4 INCH)
STEM
13A9775-B 13A9776-B
PACKINGFOLLOWER(KEY 13)
LANTERNRING (KEY 8)PACKING BOXRING (KEY 11)
1
12.7 mm(1/2 INCH)
STEM
DOUBLE ARRANGEMENTS
GRAPHITERIBBONPACKING RING(KEY 7)
GRAPHITERIBBONPACKING RING(KEY 7)
GRAPHITEFILAMENTPACKING RING(KEY 7)
1
19.1, 25.4, & 31.8 mm(3/4, 1 & 1‐1/4 INCH)
STEM
14A1849-B 14A1780-B
1
1
Instruction ManualD100399X012
EW ValveJuly 2017
13
Note
Proper performance of the tightening procedures in step 11 compresses the spiral wound gasket (key 12, figure 22 through 23) orload ring (key 26, figure 24) enough to both load and seal the seat ring gasket (key 13, figure 22, 23 or 24). It also compresses theouter edge of the bonnet gasket (key 10, figure 22 through 24) enough to seal the body‐to‐bonnet joint.
The proper bolting procedures in step 11 include‐‐but are not limited to‐‐ensuring that bolting threads are clean, and evenlytightening the nuts onto the studs in a criss‐cross pattern. Because of the bolt‐up characteristics of spiral wound gaskets,tightening one nut may loosen an adjacent nut. Repeat the criss‐cross tightening pattern several times until each nut is tight andthe body‐to‐bonnet seal is made. When the operating temperature has been reached, perform this torquing procedure onceagain.
Note
Stud(s) and nut(s) should be installed such that the manufacturer's trademark and material grade marking is visible, allowing easycomparison to the materials selected and documented in the Emerson/Fisher serial card provided with this product.
WARNING
Personal injury or damage to equipment could occur if improper stud and nut materials or parts are used. Do not operate orassemble this product with stud(s) and nut(s) that are not approved by Emerson/Fisher engineering and/or listed on theserial card provided with this product. Use of unapproved materials and parts could lead to stresses exceeding the designor code limits intended for this particular service. Install studs with the material grade and manufacturer's identificationmark visible. Contact your Emerson Automation Solutions representative immediately if a discrepancy between actualparts and approved parts is suspected.
11. Lubricate the bolting (not necessary if factory pre‐lubricated stud bolt nuts are used) and install it, using properbolting procedures during tightening so that the body‐to‐bonnet joint will withstand test pressures and applicationservice conditions. Use the bolt torques in table 5 as guidelines.
12. Install new packing and the metal packing box parts according to the appropriate arrangement in figure 4, 5, or 6.Place a smooth‐edged pipe over the valve stem and gently tap each soft packing part into the packing box.
13. Slide the packing follower, upper wiper, and packing flange (keys 13, 12, and 3, figure 21) into position. Lubricatethe packing flange studs (key 4, figure 21) and the faces of the packing flange nuts (key 5, figure 21). Install thepacking flange nuts.
14. For spring‐loaded PTFE V‐ring packing, tighten the packing flange nuts until the shoulder on the packing follower(key 13, figure 21) contacts the bonnet.
For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 6. Then,loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 6.
For ENVIRO‐SEAL or HIGH‐SEAL live‐loaded packing, refer to the note at the beginning of the Packing Maintenancesection.
For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nutsreaches the minimum recommended torque shown in table. Then, tighten the remaining flange nuts until the packingflange is level and at a 90‐degree angle to the valve stem.
15. Mount the actuator on the valve assembly, and reconnect the actuator and valve stem according to the procedurein the appropriate actuator instruction manual.
Instruction ManualD100399X012
EW ValveJuly 2017
14
Trim Maintenance
WARNING
Avoid personal injury or property damage from sudden release of process pressure. Before performing any maintenanceoperations:
� Do not remove the actuator from the valve while the valve is still pressurized.
� Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personalinjury.
� Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure theactuator cannot suddenly open or close the valve.
� Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressureon both sides of the valve. Drain the process media from both sides of the valve.
� Vent the pneumatic actuator loading pressure and relieve any actuator spring precompression.
� Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.
� The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from thepipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or whenloosening the packing box pipe plug.
� Check with your process or safety engineer for any additional measures that must be taken to protect against processmedia.
Table 5. Body‐to‐Bonnet Bolt Torque Guidelines
VALVE SIZE, NPSBOLT TORQUES(1, 2)
N�m Lbf�ft
4x2 102 75
6x4 or 8x4 259 191
8x6CL300 or CL600 548 404
CL900 1315 970
10x8 745 550
12x6 548 404
12x8CL300 or CL600 732 540
CL900 2712 2000
1. Determined from laboratory tests.2. For other materials, contact your Emerson sales office or Local Business Partner for torques.
Table 6. Recommended Torque for Packing Flange Nuts
VALVE STEMDIAMETER PRESSURE
RATING
GRAPHITE TYPE PACKING PTFE TYPE PACKING
Minimum Torque Maximum Torque Minimum Torque Maximum Torque
mm Inches N�m Lbf�In N�m Lbf�In N�m Lbf�In N�m Lbf�In
12.71/2
CL300 7 59 10 88 3 28 5 42
12.7 CL600 9 81 14 122 4 39 7 58
19.13/4
CL300 15 133 23 199 7 64 11 95
19.1 CL600 21 182 31 274 10 87 15 131
25.41
CL300 26 226 38 339 12 108 18 162
25.4 CL600 35 310 53 466 17 149 25 223
31.81‐1/4
CL300 36 318 54 477 17 152 26 228
31.8 CL600 49 437 74 655 24 209 36 314
Instruction ManualD100399X012
EW ValveJuly 2017
15
CAUTION
In the following applicable procedures, to avoid damaging parts, do not grip the bellows shroud or other parts of thestem/bellows assembly. Grip only the flat areas on the stem where it extends out of the top of the bellows shroud.
For C‐seal construction, see the appropriate C‐seal sections in this instruction manual.
Except where indicated, key numbers in this section are referenced in figure 22 for EWD constructions, figure 22 forrestricted trim detail, figure 23 for EWS constructions, and figure 24 for EWT constructions. Refer to figures 26 and 27for Cavitrol III, figure 27 for Whisper Trim III, and figure 29 for WhisperFlo construction.
Trim Removal1. Remove the actuator and the bonnet according to steps 1 through 5 of the Replacing Packing procedure.
WARNING
Avoid personal injury or property damage from valve or packing leakage.
When lifting the valve plug stem (key 7) and attached valve plug (key 2) out of the valve, be certain that the cage (key 3)remains in the valve (key 1). This will prevent cage damage that might be caused by the cage dropping back into the valveafter being lifted part way out.
Use care to avoid damaging gasket sealing surfaces.
Each graphite piston ring (key 6) in an EWD valve is brittle and in two pieces. Use care to avoid damage to the piston ring(s)caused by dropping or rough handling.
Any damage to the gasket sealing surfaces could cause the valve to leak. The surface finish of the valve stem (key 7) iscritical for making a good packing seal. The inside surface of the cage or cage/baffle assembly (key 3) or cage retainer (key31) is critical for smooth operation of the valve plug and for making a seal with the piston ring (key 6) or seal ring (key 28).The seating surfaces of the valve plug (key 2) and the seat ring (key 9) on a metal‐seat construction are critical for tightshutoff. Protect these parts accordingly while disassembling the trim.
2. Remove the packing flange nuts, packing flange, upper wiper, and packing follower (keys 5, 3, 24, and 25, figure21). Carefully push out all the remaining packing parts from the valve side of the bonnet using a rounded rod orother tool that will not scratch the packing box wall. Clean the packing box and the metal packing parts.
3. Inspect the valve stem threads and packing box surfaces for any sharp edges which might cut the packing.Scratches or burrs could cause packing box leakage or damage to the new packing. If the surface condition cannotbe improved by light sanding, replace the damaged parts.
4. Remove the load ring (key 26) from an NPS 10x8 or 12x8 valve or the cage adaptor (key 4) from any restricted‐trimvalve through NPS 8x4, and wrap it for protection.
5. On a 102 mm (4‐inch) travel valve with Whisper Trim I cage or on any NPS 8x6 or 12x6 valve with Whisper Trim IIIcage, remove the bonnet spacer (key 32) and bonnet gasket (key 10) on top of the spacer. Then on anyconstruction with a cage retainer (key 31), remove the cage retainer and its associated gaskets. A Whisper Trim IIIcage retainer has two 3/8‐inch ‐ 16 UNC tappings in which screws or bolts can be installed for lifting.
6. Remove the cage or cage/baffle assembly (key 3) and the associated gaskets (keys 10, 11, and 12). Withfull‐capacity constructions that have FGM gasket sets, a shim (key 53) is used instead of the cage gasket (key 11). Ifthe cage is stuck in the valve, use a rubber mallet to strike the exposed portion of the cage at several points aroundits circumference.
Instruction ManualD100399X012
EW ValveJuly 2017
16
Figure 7. TSO (Tight Shutoff Trim), Detail of Protected Soft Seat
INNER PLUG
OUTER PLUG
CAGE
SEAT RING
PROTECTED SOFT SEAT
A7088
7. For constructions other than TSO (tight shutoff trim), remove the seat ring (key 9) or disk seat (key 22), seat ringgasket (key 13), and the seat ring adaptor (key 5) and adaptor gasket (key 14) where used in a restricted‐capacityconstruction. EWS and EWT PTFE‐seat constructions use a disk (key 23) sandwiched between the disk seat and diskretainer (key 21). A CL900 NPS 8x6 EWT construction with Cavitrol III cage has its spiral wound gasket (key 12) onthe side of the seat ring opposite the seat ring gasket.
8. For TSO (tight shutoff trim) constructions, perform the following steps (refer to figures 7 and 8):
� Remove the piston ring, anti‐extrusion rings, backup ring, and retainer.
� Remove the set screws that lock the outer plug to the inner plug.
� Using a strap wrench or similar tool, unscrew the outer plug from the inner plug. Do not damage the outer plugguide surfaces.
� Remove the protected soft seat seal.
� Inspect the parts for damage and replace if needed.
9. For all constructions, inspect parts for wear or damage that would prevent proper operation of the valve. Replace orrepair trim parts according to the following procedures for lapping metal seats or other valve plug maintenanceprocedures, as appropriate.
Lapping Metal Seats
CAUTION
To avoid damaging the ENVIRO‐SEAL bellows seal bonnet assembly, do not attempt to lap the metal seating surfaces. Thedesign of the assembly prevents rotation of the stem and any forced rotation will damage internal components of theENVIRO‐SEAL bellows seal bonnet.
Instruction ManualD100399X012
EW ValveJuly 2017
17
Figure 8. Typical Balanced TSO Trim
VALVE PLUGSEAL
PROTECTEDSOFT SEAT
A7096
Except with respect to the ENVIRO‐SEAL Bellows Seal Bonnet assembly, with metal seat constructions, seating surfacesof the valve plug and seat ring (keys 2 and 9, figures 24 through 26) can be lapped for improved shutoff. (Deep nicksshould be machined out rather than ground out.) Use a good quality lapping compound of a mixture of 280 to600‐grit. Apply the compound to the bottom of the valve plug.
Assemble the valve to the extent that the cage (and cage retainer and bonnet spacer, if used) is in place and thebonnet is bolted to the valve. A simple handle can be made from a piece of strap iron locked to the valve plug stemwith nuts. Rotate the handle alternately in each direction to lap the seats. After lapping, remove the bonnet, and cleanthe seat surfaces. Completely assemble the valve as described in the Trim Replacement portion of the TrimMaintenance section, and test the valve for shutoff. Repeat the lapping procedure if leakage is still excessive.
Valve Plug Maintenance
Except where indicated, key numbers in this section are referenced in figure 22 for EWD valve plugs, figure 23 for EWSvalve plugs, and figure 24 for EWT valve plugs.
CAUTION
If replacing the piston ring (key 6) or seal ring (key 28), be careful not to scratch the surfaces of the ring groove in the valveplug or any of the surfaces of the replacement ring, or the replacement ring may not seal properly.
1. With the valve plug (key 2) removed, according to the Trim Removal section, proceed as appropriate:
Instruction ManualD100399X012
EW ValveJuly 2017
18
For the EWD carbon‐filled PTFE piston ring, the ring is split in one place. If there is visible damage, spread the ringslightly, and remove it from the groove in the valve plug. To install a carbon‐filled PTFE piston ring, spread the ringapart slightly at the split, and install it over the stem and into the groove in the valve plug. The open side must facealong the stem, depending on flow direction, as shown in figure 22.
For each EWD graphite piston ring, the ring can be easily removed since it is in two pieces. A new graphite piston ring isfurnished as a complete ring. Use a vise with smooth or taped jaws to break this replacement ring into halves. Place thenew ring in the vise so that the jaws will compress the ring into an oval. Slowly compress the ring until it snaps on bothsides. If one side snaps first, do not try to tear or cut the other side. Instead, keep compressing the ring until the otherside snaps. Be sure to match the broken ends when installing the ring in the valve plug groove.
For the EWT two‐piece seal ring, the ring cannot be reused as it is a closed ring, which must be pried and/or cut fromthe groove. Then the elastomeric backup ring (key 29) can be spread slightly and removed.
To install a new two‐piece seal ring, apply a general purpose silicone‐base lubricant to both the backup ring and sealring (keys 29 and 28). Place the backup ring over the stem (key 7) and into the groove. Place the seal ring over the topedge of the valve plug (key 2) so that it enters the groove on one side of the valve plug. Slowly and gently stretch theseal ring, and work it over the top edge of the valve plug. The PTFE material in the seal ring must be permitted time tocold‐flow during the stretching procedure; so avoid jerking sharply on this ring. Stretching the seal ring over the valveplug may make it seem unduly loose when in the groove, but it will contract to its original size after insertion into thecage.
For the EWT spring‐loaded seal ring, the ring used on a valve plug having a 136.5 mm (5.375 inch) or less portdiameter may be removed undamaged by first working the retaining ring (key 27) off with a screwdriver. Thencarefully slide the metal backup ring (key 29) and seal ring (key 28) off the valve plug (key 2). The spring‐loaded sealring used on a valve plug having a 178 mm (7‐inch) or greater port diameter must be carefully pried and/or cut from itsgroove. Therefore, it cannot be reused.
A spring‐loaded seal ring must be installed so that its open side faces toward either the top or the bottom of the valveplug, depending on flow direction, as shown in view A of figure 24. To install a spring‐loaded seal ring on a valve plugwith a 136.5 mm (5.375 inch) or less port diameter, slide the seal ring (key 28) onto the valve plug followed by themetal backup ring (key 29). Then install the retaining ring (key 27) by inserting one end in the groove and, whileturning the plug, press the ring into the groove. Again, be careful not to scratch any surfaces of the ring or plug.
To install the seal ring on a valve plug with 178 mm (7‐inch) or greater port diameter, lubricate it with a generalpurpose silicone‐base lubricant. Then gently stretch the seal ring, and work it over the top edge of the valve plug. ThePTFE material in the seal ring must be permitted time to cold‐flow during the stretching procedure; so avoid jerkingsharply on the ring. Stretching the seal ring over the valve plug may make it seem unduly loose when in the groove,but it will contract to its original size after insertion into the cage.
CAUTION
Never reuse an old stem or adaptor with a new valve plug. Using an old stem or adaptor with a new plug requires drilling anew pin hole in the stem (or adaptor in case an ENVIRO‐SEAL bellows seal bonnet is being used). This drilling weakens thestem or adaptor and may cause failure in service. However, a used valve plug may be reused with a new stem or adaptorexcept with Cavitrol III trim.
Note
The valve plug and valve plug stem for Cavitrol III trim are a matched set and must be ordered together. If the Cavitrol III valve plugor valve plug stem is damaged, replace the entire assembly (key 2, figure 26 and 27).
2. To replace the valve stem (key 7), drive out the pin (key 8). Unscrew the valve plug from the stem or adaptor.
Instruction ManualD100399X012
EW ValveJuly 2017
19
3. To replace the adaptor (key 24, figure 21) on ENVIRO‐SEAL bellows seal bonnets, place the plug stem assembly andvalve plug in a soft‐jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not aseating surface. Drive out the pin (key 36, figure 21). Reverse the plug stem assembly and valve plug in the soft‐jawchuck or vise. Grip the flat areas on the valve stem just below the threads for the actuator/stem connection.Unscrew the valve plug/adaptor assembly (key 24, figure 21) from the valve stem assembly (key 20, figure 21).
4. Screw the new stem or adaptor into the valve plug. Tighten to the torque value given in table 7. Refer to table 7 toselect the proper drill size. Drill through the stem or adaptor, using the hole in the valve plug as a guide. Removeany chips or burrs, and drive in a new pin to lock the assembly.
5. For ENVIRO‐SEAL bellows seal bonnets, grip the flats of the stem extending out of the top of the bellows shroudwith a soft‐jaw chuck or other type of vise. Screw the valve plug/adaptor assembly onto the valve stem. Tighten asnecessary to align the pin hole in the stem with one of the holes in the adaptor. Secure the adaptor to the stem witha new pin.
Trim Replacement
Except where indicated, key numbers in this section are referenced in figure 22 for EWD constructions, figure 22 forrestricted trim detail, figure 23 for EWS construction, and figure 24 for EWT constructions. Refer to figures 26 and 27for Cavitrol III, figure 28 for Whisper Trim III, and figure 29 for WhisperFlo constructions.
1. With a restricted‐trim seat ring construction, install the adaptor gasket (key 14) and seat ring adaptor (key 5).
2. Install the seat‐ring gasket (key 13), seat ring (key 9), or disk seat (key 22). With a PTFE‐seat construction install thedisk and disk retainer (keys 21 and 23). With an NPS 8x6 CL900 EWT valve with Cavitrol III cage, install the spiralwound gasket (key 12) on the seat ring.
3. Install the cage or cage/baffle assembly (key 3). Any rotational orientation of the cage or assembly with respect tothe valve is acceptable. A Whisper Trim III cage designated by level A3, B3, or C3 may be installed with either endup. The level D3 cage/baffle assembly or Cavitrol III cage assembly, however, must be installed with the hole patternend next to the seat ring. If a cage retainer (key 31) is to be used, place it on top of the cage.
4. For constructions other than TSO (tight shutoff trim), slide the valve plug (key 2) and stem assembly or valve plugand ENVIRO‐SEAL bellows seal assembly into the cage. Make sure the piston ring or seal ring (key 6 or 28) is evenlyengaged in the entrance chamfer at the top of the cage (key 3) or cage retainer (key 31) to avoid damaging the ring.
5. For TSO (tight shutoff) trim constructions, perform the following steps (refer to figures 7 and 8).
� Thread the outer plug onto the inner plug until the parts seat metal to metal, using a strap wrench or similar toolthat will not damage the outer plug guide surfaces.
� Mark the top of the inner plug and outer plug with alignment marks in the assembled position.
Table 7. Valve Stem to Plug Torque and Pin Replacement DataVALVE STEM DIAMETER STEM TORQUE, MINIMUM TO MAXIMUM
DRILL SIZE, INCHESmm Inch N�m Lbf�ft
12.7 1/2 81 to 115 60 to 85 1/8
19.1 3/4 237 to 339 175 to 250 3/16
25.4 1 420 to 481 310 to 355 1/4
31.8 1‐1/4 827 to 908 610 to 670 1/4
� Disassemble the outer plug from the inner plug and install the seal over the inner plug, so that the seal rests belowthe threaded area.
� Thread the outer plug onto the inner plug and tighten with a strap wrench or similar tool until the alignment marksline up. This will ensure that the plug parts are metal to metal and the seal is compressed properly. Do not damagethe outer plug guide surfaces.
� Install set screws centering the inner plug in the outer plug and torque to 11 N�m (8 lbf�ft).
Instruction ManualD100399X012
EW ValveJuly 2017
20
� Assemble the piston ring, anti‐extrusion rings, backup ring, and retainer.
6. For all constructions, place the gaskets (keys 12, 11 or 14 if used, and 10) and the shim, if used (key 53), on top ofthe cage or cage retainer. If there is a cage adaptor (key 4) or a bonnet spacer (key 32), set it on the cage or cageretainer gaskets and place another flat sheet gasket (key 10) on top of the adapter or spacer. If there is only a cageretainer or bonnet spacer, place another flat sheet gasket on the retainer or spacer.
7. With an NPS 10x8 or 12x8 valve, install the load ring (key 26).
8. Mount the bonnet on the valve, and complete assembly according to steps 11 through 15 of the Replacing Packingsection. Be sure to observe the note prior to step 11.
Retrofit: Installing C‐seal Trim
Note
Additional actuator thrust is required for a valve with C‐seal trim. When installing C‐seal trim in an existing valve, contact yourEmerson sales office or Local Business Partner for assistance in determining new actuator thrust requirements.
Assemble the new valve plug/retainer assembly (with C‐seal plug seal) using the following instructions:
CAUTION
To avoid leakage when the valve is returned to service, use appropriate methods and materials to protect all sealingsurfaces of the new trim parts while assembling the individual parts and during installation in the valve body.
1. Apply a suitable high‐temperature lubricant to the inside diameter of the C‐seal plug seal. Also, lubricate theoutside diameter of the valve plug where the C‐seal plug seal must be pressed into the proper sealing position(figure 9).
2. Orient the C‐seal plug seal for correct sealing action based on the process fluid flow direction through the valve.
� The open interior of the C‐seal plug seal must face up in a valve with flow‐up construction (figure 9).
� The open interior of the C‐seal plug seal must face down in a valve with flow‐down construction (figure 9).
Note
An installation tool must be used to properly position the C‐seal plug seal on the valve plug. A tool is available as a spare part fromEmerson or a tool could be manufactured following the dimensions given in figure 10.
3. Place the C‐seal plug seal over the top of the valve plug and press the C‐seal plug seal onto the plug using the C‐sealinstallation tool. Carefully press the C‐seal plug seal onto the plug until the installation tool contacts the horizontalreference surface of the valve plug (figure 11).
4. Apply a suitable high‐temperature lubricant to the threads on the plug. Then, place the C‐seal retainer onto theplug and tighten the retainer using an appropriate tool such as a strap wrench.
5. Using an appropriate tool such as a center punch, stake the threads on top of the plug in one place (figure 12) tosecure the C‐seal retainer.
Instruction ManualD100399X012
EW ValveJuly 2017
21
Figure 9. Fisher EWD with C‐seal Trim
A6790
FLOW DOWN FLOW UP
A
VIEW A
64 64
9
2
64
65
8
7
6. Install the new plug/retainer assembly with C‐seal plug seal on the new stem following the appropriate instructionsin the Trim Replacement section of this manual.
7. Install piston rings by following instructions in the Trim Replacement section of this manual.
8. Remove the existing valve actuator and bonnet following the appropriate instructions in the Replacing Packingsection in this manual.
CAUTION
Do not remove the existing valve stem from the valve plug unless you are planning to replace the valve stem.
Never reuse an old valve stem with a new plug or reinstall a valve stem after it has been removed. Replacing a valve stemrequires drilling a new pin hole in the stem. This drilling weakens the stem and may cause failure in service. However, aused valve plug may be reused with a new valve stem.
9. Remove the existing valve stem and plug, cage, and seat ring from the valve body following the appropriateinstructions in the Trim Removal section in this manual.
10. Replace all gaskets according to appropriate instructions in the Trim Replacement section in this manual.
11. Install the new seat ring, cage, valve plug/retainer assembly, and stem into the valve body and completelyreassemble the valve package following the appropriate instructions in the Trim Replacement section in thismanual.
Instruction ManualD100399X012
EW ValveJuly 2017
22
FOR VALVEPLUGS
FITTINGPORT SIZE
(Inches)
DIMENSIONS, mm(See Drawing Below) Part Number
(To OrderA Tool)
A B C D E F G H
2.875 82.5552.324 ‐52.578
4.978 ‐ 5.029 3.708 ‐ 3.759 41.14852.680 ‐52.781
55.118 ‐55.626
70.891 ‐ 71.044 24B9816X012
3.4375 101.658.674 ‐58.928
4.978 ‐ 5.029 3.708 ‐ 3.759 50.861.011 ‐61.112
63.449 ‐63.957
85.166 ‐ 85.319 24B5612X012
3.625 104.39465.024 ‐65.278
4.978 ‐ 5.029 3.708 ‐ 3.759 50.868.936 ‐69.037
71.374 ‐71.882
89.941 ‐ 90.094 24B3630X012
4.375 125.98483.439 ‐83.693
4.978 ‐ 5.029 3.708 ‐ 3.759 50.887.351 ‐87.452
89.789 ‐90.297
108.991 ‐ 109.144 24B3635X012
5.375 142.748100.076 ‐
100.334.978 ‐ 5.029 3.708 ‐ 3.759 45.974
103.835 ‐103.937
106.274 ‐106.782
128.219 ‐ 128.372 23B9193X012
7 184.15141.376 ‐141.630
4.978 ‐ 5.029 3.708 ‐ 3.759 60.198145.136 ‐145.237
147.574 ‐148.082
169.520 ‐ 169.672 23B9180X012
8 209.55166.776 ‐167.030
4.978 ‐ 5.029 3.708 ‐ 3.759 55.88170.536 ‐170.637
172.974 ‐173.482
194.920 ‐ 195.072 24B9856X012
FOR VALVEPLUGS
FITTINGPORT SIZE
(Inches)
DIMENSIONS, INCHES(See Drawing Below) Part Number
(To OrderA Tool)
A B C D E F G H
2.875 3.25 2.060 ‐ 2.070 0.196 ‐ 0.198 0.146 ‐ 0.148 1.62 2.074 ‐ 2.078 2.170 ‐ 2.190 2.791 ‐ 2.797 24B9816X012
3.4375 4.00 2.310 ‐ 2.320 0.196 ‐ 0.198 0.146 ‐ 0.148 2.00 2.402 ‐ 2.406 2.498 ‐ 2.518 3.353 ‐ 3.359 24B5612X012
3.625 4.11 2.560 ‐ 2.570 0.196 ‐ 0.198 0.146 ‐ 0.148 2.00 2.714 ‐ 2.718 2.810 ‐ 2.830 3.541 ‐ 3.547 24B3630X012
4.375 4.96 3.285 ‐ 3.295 0.196 ‐ 0.198 0.146 ‐ 0.148 2.00 3.439 ‐ 3.443 3.535 ‐ 3.555 4.291 ‐ 4.297 24B3635X012
5.375 5.62 3.940 ‐ 3.950 0.196 ‐ 0.198 0.146 ‐ 0.148 1.81 4.088 ‐ 4.092 4.184 ‐ 4.204 5.048 ‐ 5.054 23B9193X012
7 7.25 5.566 ‐ 5.576 0.196 ‐ 0.198 0.146 ‐ 0.148 2.37 5.714 ‐ 5.718 5.810 ‐ 5.830 6.674 ‐ 6.680 23B9180X012
8 8.25 6.566 ‐ 6.576 0.196 ‐ 0.198 0.146 ‐ 0.148 2.20 6.714 ‐ 6.718 6.810 ‐ 6.830 7.674 ‐ 7.680 24B9856X012
Figure 10. C‐seal Plug Seal Installation Tool
45° X 0.06
∅A
∅B
8° - 9°
DC
∅F
∅G
∅H
E
BREAK SHARPCORNER45° X 0.01 MAX
45° X 0.02
A6777
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
Instruction ManualD100399X012
EW ValveJuly 2017
23
Figure 11. Installing the C‐seal Plug Seal Using the Installation Tool
NOTE:PRESS INSTALLATION TOOL OVER VALVE PLUG UNTIL THE TOOL CONTACTS THEHORIZONTAL REFERENCE SURFACE OF THE VALVE PLUG.
C‐SEALMETALPLUGSEAL
INSTALLATIONTOOL
A6778
VALVEPLUG
HORIZONTALREFERENCESURFACE
FLOW DOWN
Figure 12. Stake the Threads of the C‐seal Retainer
C‐SEALMETALPLUGSEAL VALVE
PLUG
FLOW DOWN
PISTONRING
RETAINER
DEFORM THREAD TOSTAKE C‐SEAL RETAINER
A6779
Instruction ManualD100399X012
EW ValveJuly 2017
24
CAUTION
To avoid excessive leakage and seat erosion, the valve plug must be initially seated with sufficient force to overcome theresistance of the C‐seal plug seal and contact the seat ring. You can correctly seat the valve plug by applying the fullactuator load. This force will adequately drive the valve plug to the seat ring, thus giving the C‐seal plug seal apredetermined permanent set. Once this is done, the plug/retainer assembly, the cage, and the seat ring become amatched set.
With full actuator force applied and the valve plug fully seated, align the actuator travel indicator scale with the lower endof valve travel. Refer to the appropriate actuator instruction manual for information on this procedure.
Replacement of Installed C‐seal Trim
Trim Removal (C‐seal Constructions)1. Remove the valve actuator and bonnet following the appropriate instructions in the Replacing Packing section in
this manual.
CAUTION
To avoid leakage when the valve is returned to service, use appropriate methods and materials to protect all sealingsurfaces of the trim parts during maintenance.
Use caution when removing piston ring(s) and C‐seal plug seal to avoid scratching any sealing surface.
CAUTION
Do not remove the valve stem from the plug/retainer assembly unless you are planning to replace the valve stem.
Never reuse an old valve stem with a new plug or reinstall a valve stem after it has been removed. Replacing a valve stemrequires drilling a new pin hole in the stem. This drilling weakens the stem and may cause failure in service. However, aused valve plug may be reused with a new valve stem.
2. Remove the plug/retainer assembly (with C‐seal plug seal), cage, and seat ring from the valve body following theappropriate instructions in the Trim Removal section of this manual.
3. Locate the staked thread on top of the valve plug (figure 12). The staked thread secures the retainer. Use a drill witha 1/8 inch bit to drill out the staked area of the thread. Drill approximately 1/8 inch into the metal to remove thestaking.
4. Locate the break between sections of the piston ring(s). Using an appropriate tool such as a flat‐blade screwdriver,carefully pry out the piston ring(s) from the groove(s) in the C‐seal retainer.
5. After removing the piston ring(s), locate the 1/4‐inch diameter hole in the groove. In a retainer with two piston ringgrooves, the hole will be found in the upper groove.
6. Select an appropriate tool such as a punch and place the tip of the tool into the hole with the body of the tool heldtangent to the outside diameter of the retainer. Strike the tool with a hammer to rotate the retainer and free it fromthe valve plug. Remove the retainer from the plug.
7. Use an appropriate tool such as a flat‐blade screwdriver to pry the C‐seal plug seal off the plug. Use caution to avoidscratches or other damage to the sealing surfaces where the C‐seal plug seal makes contact with the valve plug(figure 13).
Instruction ManualD100399X012
EW ValveJuly 2017
25
Figure 13. Lower (Valve Plug to Seat Ring) and Upper (C‐seal Plug Seal to Cage) Seating Surfaces
C‐seal METALPLUG SEAL
RETAINER
CAGEVALVE PLUG
NOTE: UPPER SEATING SURFACE IS THE AREA OF CONTACT BETWEENTHE C‐seal METAL PLUG SEAL AND THE CAGE.
PLUG
CAGE
SEATRING
UPPER SEATING SURFACE
LOWER SEATING SURFACEA6780
1
1
8. Inspect the lower seating surface where the valve plug contacts the seat ring for wear or damage which wouldprevent proper operation of the valve. Also, inspect the upper seating surface inside the cage where the C‐seal plugseal contacts the cage, and inspect the sealing surface where the C‐seal plug seal makes contact with the plug(figure 13).
9. Replace or repair trim parts according to the following procedure for lapping metal seats, remachining metal seats,or other valve plug maintenance procedures as appropriate.
Lapping Metal Seats (C‐seal Constructions)
Before installing a new C‐seal plug seal, lap the lower seating surface (valve plug to seat ring, figure 13) following appropriate procedures in the Lapping Metal Seats section of this manual.
Remachining Metal Seats (C‐seal Constructions)
See figure 14. A valve plug with a C‐seal metal plug seal features two seating surfaces. One seating surface is foundwhere the valve plug contacts the seat ring. The second seating surface is found where the C‐seal plug seal contactsthe upper seating surface in the cage. If you machine the seats on the seat ring and/or plug, you must machine anequal dimension from the seating area in the cage.
CAUTION
If metal is removed from the seat ring and plug and a corresponding amount is not removed from the cage seating area, theC‐seal plug seal will be crushed as the valve closes and the C‐seal retainer will strike the seating area of the cage, preventingthe valve from closing.
Instruction ManualD100399X012
EW ValveJuly 2017
26
Figure 14. Example of Machining the Lower (Valve Plug to Seat Ring) and Upper (C‐seal Plug Seal to Cage) SeatingSurfaces
UPPER SEATINGSURFACE
C‐sealRETAINER
MACHINING OF THE UPPERSEATING SURFACE MUSTEQUAL THE TOTAL MACHINING OFTHE LOWER SEATING SURFACE(PLUG PLUS SEAT RING). IF NOT, THERETAINER MAY STRIKE THE UPPERSEATING SURFACE BEFORE THEVALVE PLUG PROPERLY SEATS ONTHE LOWER SEATING SURFACE.
LOWER SEATING SURFACE
PLUS
SEATRING
PLUG
CAGE
A6781 / IL
1
3
2
123
NOTE:
0.508 (0.020)(4)
0.254 (0.010)(4)
0.254 (0.010)(4)
REMOVAL OF 0.254 mm (0.010 inch) FROM THE VALVE PLUGREMOVAL OF 0.254 mm (0.010 inch) FROM THE SEAT RING
REMOVAL OF 0.508 mm (0.020 inch) FROM THE UPPERSEATING SURFACE IN THE CAGE4. THESE VALUES ARE FOR EXAMPLE ONLY. REMOVE ONLY THE MINIMUM AMOUNT OF MATERIAL REQUIRED TO REFURBISH THE SEATS.
Trim Replacement (C‐seal Constructions)1. Apply a suitable high‐temperature lubricant to the inside diameter of the C‐seal plug seal. Also, lubricate the
outside diameter of the valve plug where the C‐seal plug seal must be pressed into the proper sealing position(figure 9).
2. Orient the C‐seal plug seal for correct sealing action based on the process fluid flow direction through the valve.
� The open interior of the C‐seal plug seal must face up in a valve with flow‐up construction (figure 9).
� The open interior of the C‐seal plug seal must face down in a valve with flow‐down construction (figure 9).
Note
An installation tool must be used to properly position the C‐seal plug seal on the valve plug. A tool is available as a spare part fromEmerson or a tool could be manufactured following the dimensions given in figure 10.
Instruction ManualD100399X012
EW ValveJuly 2017
27
3. Place the C‐seal plug seal over the top of the valve plug and press it onto the plug using the installation tool.Carefully press the C‐seal plug seal onto the plug until the installation tool contacts the horizontal reference surfaceof the valve plug (figure 11).
4. Apply a suitable high‐temperature lubricant to the threads on the plug. Then, place the C‐seal retainer onto theplug and tighten the retainer using an appropriate tool such as a strap wrench.
5. Using an appropriate tool such as a center punch, stake the threads on top of the plug in one place (figure 12) tosecure the C‐seal retainer.
6. Replace the piston ring(s) following instructions in the Trim Replacement section of this manual.
7. Return the seat ring, cage, plug/retainer assembly, and stem to the valve body and completely reassemble the valvepackage following the appropriate instructions in the Trim Replacement section of this manual.
CAUTION
To avoid excessive leakage and seat erosion, the valve plug must be initially seated with sufficient force to overcome theresistance of the C‐seal plug seal and contact the seat ring. You can correctly seat the valve plug by applying the fullactuator load. This force will adequately drive the valve plug to the seat ring, thus giving the C‐seal plug seal apredetermined permanent set. Once this is done, the plug/retainer assembly, the cage, and the seat ring become amatched set.
With full actuator force applied and the valve plug fully seated, align the actuator travel indicator scale with the lower endof valve travel. Refer to the appropriate actuator instruction manual for information on this procedure.
ENVIRO‐SEAL Bellows Seal Bonnet
Replacing a Plain or Extension Bonnet with an ENVIRO‐SEAL Bellows Seal Bonnet(Stem/Bellows Assembly)
Except where indicated, key numbers in this section are referenced in figure 22 for EWD constructions, figure 22 forrestricted trim detail, figure 23 for EWS constructions, and figure 24 for EWT constructions. Refer to figures 26 and 27for Cavitrol III, figure 27 for Whisper Trim III, and figure 29 for WhisperFlo constructions.
Table 8. Recommended Torque for ENVIRO‐SEAL Bellows Seal Bonnet Packing Flange Nuts
VALVE SIZE,NPS
VALVE STEMDIAMETER THROUGH
PACKING
MINIMUM TORQUE MAXIMUM TORQUE
N�m Lbf�in N�m Lbf�in
4x2 1/2 2 22 4 33
6x4 to 12x8 1 5 44 8 67
1. Remove the actuator and bonnet according to steps 1 through 6 of the Replacing Packing procedure in theMaintenance section.
2. Lift out the cage.
3. Remove and discard the existing bonnet gasket. Cover the valve body opening to protect sealing surfaces and toprevent foreign material from entering the valve body cavity.
Note
The ENVIRO‐SEAL stem/bellows assembly for easy-e� valves is available only with a threaded and drilled plug/adaptor/stemconnection. The existing valve plug can be reused with the new stem/bellows assembly or a new plug can be installed.
Instruction ManualD100399X012
EW ValveJuly 2017
28
4. Inspect the existing valve plug. If the plug is in good condition, it can be reused with the new ENVIRO‐SEALstem/bellows assembly. To remove the existing valve plug from the stem, first, place the existing plug stemassembly in a soft‐jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not aseating surface. Drive out or drill out the pin (key 8).
5. Then, reverse the plug stem assembly in the soft‐jaw chuck or vise. Grip the valve stem in an appropriate place andunscrew the existing plug from the valve stem.
CAUTION
When installing a valve plug on the ENVIRO‐SEAL stem/bellows assembly, the valve stem must not be rotated. Damage tothe bellows may result.
Do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat areas on the stem where itextends out of the top of the bellows shroud.
Note
The ENVIRO‐SEAL stem/bellows assembly has a one‐piece stem.
6. To attach the valve plug to the stem of the new ENVIRO‐SEAL stem/bellows assembly, it is necessary to first attachthe plug to the adaptor (key 24, figure 21). Locate the adaptor. Notice that a hole has not been drilled in the threadswhere the plug screws onto the adaptor. Secure the valve plug in a soft‐jaw chuck or other type of vise. Do not gripthe plug on any seating surface. Position the plug in the chuck or vise for easy threading of the adaptor. Thread theadaptor into the valve plug and tighten to the appropriate torque value.
7. Select the proper size of drill bit and drill through the adaptor using the hole in the valve plug as a guide. Removeany metal chips or burrs and drive in a new pin (key 8) to lock the plug/adaptor assembly together.
8. Attach the plug/adaptor assembly to the ENVIRO‐SEAL stem/bellows assembly by first securing the stem/bellowsassembly in a soft‐jaw chuck or other type of vise so that the jaws of the chuck or vise grip the flats of the stemextending out of the top of the bellows shroud. Screw the valve plug/adaptor assembly onto the valve stem.Tighten the plug/adaptor assembly until it is snug. Then turn the plug/adaptor assembly to the next pin hole in thevalve stem. Drive in new pin (key 36, figure 21) to lock the assembly.
9. Inspect the seat ring (key 9). Replace, if necessary.
10. Place a new gasket (key 10) into the valve body in place of the bonnet gasket. Install the new stem/bellowsassembly with valve plug/adaptor by placing it into the valve body on top of the new bellows gasket.
11. Place a new gasket (key 22, figure 21) over the stem/bellows assembly. Place the new ENVIRO‐SEAL bonnet overthe stem/bellows assembly.
Instruction ManualD100399X012
EW ValveJuly 2017
29
Figure 15. PTFE Packing Arrangement for Use in Fisher ENVIRO‐SEAL Bellows Seal Bonnets
PACKING SET(KEY 6)
UPPER WIPER(KEY 12)
BUSHING(KEY 13)
FEMALEADAPTOR
PACKING RING
MALE ADAPTOR
SPACER (KEY 8)
SPACER(KEY 8)
BUSHING(KEY 13)
BUSHING(KEY 13)
THRUSTRING(KEY 39)
12B4183−A/IL
9.5 mm(3/8 INCH)
STEM
12.7 mm(1/2 INCH)
STEM, NPS 2VALVES
12.7 mm(1/2 INCH)
STEM, NPS 3 ANDNPS 4 VALVES
9.5 mm(3/8 INCH)
STEM
9.5 mm(3/8 INCH)
STEM
12.7 mm(1/2 INCH)
STEM
12.7 mm(1/2 INCH)
STEM
UPPER WIPER(KEY 12)
BUSHING(KEY 13)
PACKING RING
MALE ADAPTOR
SPACER (KEY 8)
FEMALE ADAPTOR
SPACER(KEY 8)
SPRING(KEY 8)
THRUSTRING(KEY 39)
THRUSTRING(KEY 39)
FOR S31603 (316 SST) PACKINGBOX PARTS
FOR ALL PACKING BOX MATERIALSEXCEPT S31603
SINGLE ARRANGEMENTS
DOUBLE ARRANGEMENTS
18A0906−D/IL
A5886-1
18A5338−B/IL
12B4185−A−SHT2/IL12B4182−A−SHT2/IL12B4185−A−SHT1/IL12B4182−A/IL
A5855/IL
SPACER (KEY 8)
PACKING SET(KEY 6)
Instruction ManualD100399X012
EW ValveJuly 2017
30
Note
Stud(s) and nut(s) should be installed such that the manufacturer's trademark and material grade marking is visible, allowing easycomparison to the materials selected and documented in the Emerson/Fisher serial card provided with this product.
WARNING
Personal injury or damage to equipment could occur if improper stud and nut materials or parts are used. Do not operate orassemble this product with stud(s) and nut(s) that are not approved by Emerson/Fisher engineering and/or listed on theserial card provided with this product. Use of unapproved materials and parts could lead to stresses exceeding the designor code limits intended for this particular service. Install studs with the material grade and manufacturer's identificationmark visible. Contact your Emerson Automation Solutions representative immediately if a discrepancy between actualparts and approved parts is suspected.
12. Properly lubricate the bonnet stud bolts. Install and tighten the bonnet hex nuts to the proper torque.
13. Install the new packing and the metal packing box parts according to the appropriate arrangement in figure 15 or16.
14. Install the packing flange. Properly lubricate the packing flange stud bolts and the faces of the packing flange nuts.
Figure 16. Double Graphite Ribbon/Filament Arrangements for Use in Fisher ENVIRO‐SEAL Bellows Seal Bonnets
NOTE:���0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS; USEONLY ONE BELOW EACH GRAPHITE RIBBON RING.
BUSHING(KEY 13)
SPACER (KEY 8)
9.5 mm(3/8 INCH)
STEM
12.7 mm(1/2 INCH) STEM,
FOR NPS 2 VALVES
12.7 mm (1/2 INCH)STEM, FOR NPS 3 AND
NPS 4 VALVES
GRAPHITE RIBBONPACKING RING (KEY 7)
GRAPHITE FILAMENTPACKING RING (KEY 7)
12B6102−A/IL18A090−E/IL12B4181−A/IL
A5887‐1
For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 8. Then,loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 8.
For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nutsreaches the minimum recommended torque shown in table 8. Then, tighten the remaining flange nut until thepacking flange is level and at a 90‐degree angle to the valve stem.
Instruction ManualD100399X012
EW ValveJuly 2017
31
15. Install the travel indicator parts and stem locknuts; mount the actuator on the valve body according to theprocedure in the appropriate actuator instruction manual.
Replacement of an Installed ENVIRO‐SEAL Bellows Seal Bonnet (Stem/Bellows Assembly)1. Remove the actuator and bonnet according to steps 1 through 6 of the Replacing Packing procedure of the
Maintenance section.
2. Lift out the cage. Remove and discard the existing bonnet gasket and bellows gasket. Cover the valve body openingto protect sealing surfaces and to prevent foreign material from entering the valve body cavity.
CAUTION
The ENVIRO‐SEAL stem/bellows assembly for easy-e valves is available only with a threaded and pinned plug/adaptor/stemconnection. The existing valve plug can be reused with the new stem/bellows assembly or a new plug can be installed. Ifthe existing valve plug is reused, and the adaptor is in good condition, it may be reused also. However, never reuse an oldadaptor with a new valve plug. Using an old adaptor with a new valve plug requires drilling a new pin hole in the adaptor.This drilling weakens the adaptor and may cause failure in service. However, a used valve plug may be reused with a newadaptor.
3. Inspect the existing valve plug and adaptor. If they are in good condition, they can be reused with the newstem/bellows assembly and they do not need to be separated.
CAUTION
When removing/installing a valve plug on the ENVIRO‐SEAL stem/bellows assembly, the valve stem must not be rotated.Damage to the bellows may result.
Do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat areas on the stem where itextends out of the top of the bellows shroud.
Note
The ENVIRO‐SEAL stem/bellows assembly has a one‐piece stem.
4. If the valve plug and adaptor are not in good condition and must be replaced, the valve plug/adaptor assemblymust first be removed from the stem/bellows assembly and then the valve plug removed from the adaptor. First,place the stem/bellows assembly and valve plug in a soft‐jaw chuck or other type of vise so that the jaws grip aportion of the valve plug that is not a seating surface. Drive out or drill out the pin (key 8). Drive out the pin (key 36,figure 21).
5. Then, reverse the stem/bellows and plug/adaptor assembly in the soft‐jaw chuck or vise. Grip the flat areas on thevalve stem just below the threads for the actuator/stem connection. Unscrew the plug/adaptor assembly from thestem/bellows assembly. Unscrew the valve plug from the adaptor.
6. To attach either the existing or a new valve plug to the stem of the new ENVIRO‐SEAL stem/bellows assembly, firstattach the plug to the adaptor (if the valve plug was removed from the adaptor) as follows:
� Locate the adaptor. Notice that a hole has not been drilled in the new adaptor threads where the plug screws ontothe adaptor.
� Secure the valve plug in a soft‐jaw chuck or other type of vise. Do not grip the plug on any seating surface. Positionthe plug in the chuck or vise for easy threading of the adaptor.
Instruction ManualD100399X012
EW ValveJuly 2017
32
� Thread the adaptor into the valve plug and tighten to the appropriate torque value.
7. Complete the installation by following steps 7 through 15 of the ENVIRO‐SEAL Bellows Seal Bonnet installationinstructions given above.
Purging the ENVIRO‐SEAL Bellows Seal Bonnet
The ENVIRO‐SEAL bellows seal bonnet has been designed so that it can be purged or leak tested. Refer to figure 21 foran illustration of an ENVIRO‐SEAL bellows seal bonnet. Perform the following steps for purging or leak testing.
1. Remove the two diametrically opposed pipe plugs (key 16, figure 21).
2. Connect a purging fluid to one of the pipe plug connections.
3. Install appropriate piping or tubing in the other pipe plug connection to pipe away the purging fluid or to make aconnection to an analyzer for leak testing.
4. When purging or leak testing has been completed, remove the piping or tubing and reinstall the pipe plugs (key 16,figure 21).
Parts OrderingEach body‐bonnet assembly is assigned a serial number, which can be found on the valve. This same number alsoappears on the actuator nameplate when the valve is shipped from the factory as part of a control valve assembly.Refer to the serial number when contacting your Emerson sales office or Local Business Partner for technicalassistance. When ordering replacement parts, refer to the serial number and to the 11‐character part number for eachpart required from the following parts list.
WARNING
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions shouldnot, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect theperformance of the valve, and could cause personal injury and property damage.
Instruction ManualD100399X012
EW ValveJuly 2017
33
Parts Kits
Gasket KitsGasket Kits (includes keys 10, 12, 13, and 53; plus 11 and 14 for restricted trim)
VALVE SIZE, NPS
Standard Trim CageWhisper Trim I Cage
Cavitrol III - 1 Stage Cage
Cavitrol III - 2 Stage CageWhisper Trim III Cage
WhisperFlo Cage
-198 to 593�C (-325 to 1100�F) -198 to 593�C (-325 to 1100�F)
Part Number Part Number
4x2 RGASKETX182 RGASKETX442
6x4x2‐1/2 RGASKETX282 - - -
6x4 or 8x4 RGASKETX212 RGASKETX472
8x6 or 12x6CL300, CL600, or CL900
RGASKETX392 - - -
8x6 or 12x6Whisper Trim I
RGASKETX412(1) - - -
10x8 or 12x8 RGASKETX232 10A3265X152
1. Includes a quantity 2 of key 10.
Packing Kits
Standard Packing Repair Kits
Packing repair kits for standard packing include keys 6, 8, 10, 11 and 12.
Note
Kits do not apply to alloy C (N10276 and CW2M), Alloy 20 (N08020 and CN7M), or alloy 400 (N04400 and M35‐1) trims.
Standard Packing Repair Kits (Non Live‐Loaded)Stem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)12.7 (1/2)
71 (2‐13/16)19.1 (3/4)
90 (3‐9/16)25.4 (1)127 (5)
31.8 (1-1/4)127 (5, 5H)
PTFE (Contains keys 6, 8, 10, 11, and 12) RPACKX00022 RPACKX00032 RPACKX00342 RPACKX00352
Double PTFE (Contains keys 6, 8, 11, and 12) RPACKX00052 RPACKX00062 RPACKX00362 RPACKX00372
PTFE/Composition (Contains keys 7, 8, 11, and 12) RPACKX00082 RPACKX00092 - - - - - -
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], 8, and 11)
RPACKX00112 RPACKX00122 - - - - - -
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], and 11)
- - - - - - RPACKX00532 RPACKX00542
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring])
RPACKX00142 RPACKX00152 - - - - - -
Double Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], 8, and 11)
RPACKX00172 RPACKX00182 - - - - - -
Instruction ManualD100399X012
EW ValveJuly 2017
34
HIGH‐SEAL and ENVIRO‐SEAL Packing Retrofit Kits
Retrofit kits include parts to convert valves with existing standard bonnets to the HIGH‐SEAL or ENVIRO‐SEAL packingbox construction. Refer to figure 17 for key numbers for HIGH‐SEAL packing. For ENVIRO‐SEAL packing, refer to figure18 for PTFE packing key numbers, figure 19 for Graphite ULF packing key numbers, and figure 20 for duplex packingkey numbers.
Stems and packing box constructions that do not meet Emerson stem finish specifications, dimensional tolerances,and design specifications, may adversely alter the performance of this packing kit.
HIGH‐SEAL Packing Retrofit KitsStem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)12.7 (1/2)
71 (2‐13/16)19.1 (3/4)
90 (3‐9/16)25.4 (1)127 (5)
31.8 (1‐1/4)127 (5, 5H)
4200 psi Process Pressure Rating (Contains keys 200through 212)
11B2182X052 11B2184X052 11B2187X052 11B2189X052
ENVIRO‐SEAL Packing Retrofit KitsStem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)12.7 (1/2)
71 (2‐13/16)19.1 (3/4)
90 (3‐9/16)25.4 (1)127 (5)
31.8 (1‐1/4)127 (5, 5H)
Double PTFE (Contains keys 200, 201, 211, 212, 214,215, 217, 218, tag, cable tie)
RPACKXRT022 RPACKXRT032 RPACKXRT042 RPACKXRT052
Graphite ULF (Contains keys 200, 201, 207, 208, 209,210, 211, 212, 214, 217, tag, cable tie)
RPACKXRT272 RPACKXRT282 RPACKXRT292 RPACKXRT302
Duplex (Contains keys 200, 201, 207, 209, 211, 212,214, 215, 216, 217, tag, cable tie)
RPACKXRT222 RPACKXRT232 RPACKXRT242 RPACKXRT252
ENVIRO‐SEAL Packing Repair Kits
Repair kits include parts to replace the ”soft” packing materials in valves that already have ENVIRO‐SEAL packingarrangements installed or in valves that have been upgraded with ENVIRO‐SEAL retrofit kits. Refer to figure 18 for keynumbers for PTFE packing, figure 19 for key numbers for Graphite ULF packing, and figure 20 for key numbers forduplex packing.
Stems and packing box constructions that do not meet Emerson stem finish specifications, dimensional tolerances,and design specifications, may adversely alter the performance of this packing kit.
ENVIRO‐SEAL Packing Repair KitsStem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)12.7 (1/2)
71 (2‐13/16)19.1 (3/4)
90 (3‐9/16)25.4 (1)127 (5)
31.8 (1‐1/4)127 (5, 5H)
Double PTFE (Contains keys 214, 215, 218) RPACKX00202 RPACKX00212 RPACKX00222 RPACKX00232
Graphite ULF (Contains keys 207, 208, 209, 210, 214) RPACKX00602 RPACKX00612 RPACKX00622 RPACKX00632
Duplex (Contains keys 207, 209, 214, 215) RPACKX00302 RPACKX00312 RPACKX00322 RPACKX00332
Instruction ManualD100399X012
EW ValveJuly 2017
35
Figure 17. Typical Fisher HIGH‐SEAL Packing System
A6138
STUD(KEY 200)
HEX NUT(KEY 212)
PACKINGFLANGE(KEY 201)SPRING(KEY 202)
PACKING RING(KEY 209)GRAPHITE RIBBONPACKING RING(KEY 210)
PACKINGBOX RING(KEY 211)
SCREW(KEY 204)
LOADSCALE(KEY 205)INDICATORDISK(KEY 206)PACKINGFOLLOWER(KEY 203)GUIDEBUSHING(KEY 207)GUIDEBUSHING(KEY 208)
Figure 18. Typical Fisher ENVIRO‐SEAL Packing System with PTFE Packing
A6297‐1
Figure 19. Typical Fisher ENVIRO‐SEAL Packing System with Graphite ULF Packing
39B4612/A
Figure 20. Typical Fisher ENVIRO‐SEAL Packing System with Duplex Packing
200
212
201
215
216
207
209
211
217
207
207
207
214
213
A6722
Instruction ManualD100399X012
EW ValveJuly 2017
36
Parts ListNumerous available combinations of valve parts makeselection of some parts difficult; when ordering valveparts for which a part number is not listed, provide thevalve serial number with the order, permitting properselection of replacement parts to be made at thefactory.
Note
Part numbers are shown for recommended spares only. For part
numbers not shown, contact your Emerson sales office or Local Business
Partner.
Bonnet (figures 4, 5, 6, and 21)Key Description Part Number
1 Bonnet
If you need a bonnet and/or and ENVIRO‐SEAL bellows seal
bonnet as a replacement part, order by valve size and stem
diameter, serial number, and desired material.
2 Extension Bonnet Bushing
3 Packing Flange
3 ENVIRO‐SEAL bellows seal packing flange
4 Packing Flange Studs
4 ENVIRO‐SEAL bellows seal stud bolt (2 req'd)
5 Packing Flange Nuts
5 ENVIRO‐SEAL bellows seal packing flange
nut (2 req'd)
6* Single PTFE V‐Ring Packing Set See following table
6* ENVIRO‐SEAL bellows seal packing set
PTFE (1 req'd for single, 2 req'd for
double)
Size 4x2 w/ 12.7 mm (1/2 inch) stem 12A9016X012
Sizes 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem
(For double PTFE only)(2 req'd) 12A8832X012
7* Individual Packing Ring See following table
7* ENVIRO‐SEAL bellows seal packing ring
Double packing graphite filament
(4 req'd)
Size 4x2 w/ 12.7 mm (1/2 inch) stem 1P3905X0172
Sizes 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 14A0915X042
7* ENVIRO‐SEAL bellows seal packing ring
Double packing graphite ribbon
(4 req'd)
Size 4x2 w/ 12.7 mm (1/2 inch) stem 18A0908X012
Sizes 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 18A0918X012
8 Packing Box Spring or Lantern Ring
8 ENVIRO‐SEAL bellows seal spring, 316 SST
Size 4x2 w/ 12.7 mm
(1/2 inch) stem (single packing only)
8 ENVIRO‐SEAL bellows seal spacer, S31600
For single PTFE packing
Size 4x2 w/ 12.7 mm (1/2 inch) stem
Key Description Part Number
For double PTFE, graphite rib/fil packing
Size 4x2 w/ 12.7 mm (1/2 inch) stem (2 req'd)
Size 6x4x2‐1/2, 6x4, & 8x4
w 12.7 mm (1/2 inch) stem (2 req'd)
8 ENVIRO‐SEAL bellows seal spacer, N10276
For single PTFE packing)
Size 4x2 w/ 12.7 mm (1/2 inch) stem
(1 req'd)
For double PTFE, graphite rib/fil packing
Size 4x2 w/ 12.7 mm (1/2 inch) stem (2 req'd)
Size 6x4x2‐1/2, 6x4, & 8x4
w 12.7 mm (1/2 inch) stem (2 req'd)
9* Individual Packing Ring See following table
10 Special Washer See following table
11* Packing Box Ring, S31600
12.7 mm (1/2 inch) stem 1J873235072
19.1 mm (3/4 inch) stem 1J873335072
25.4 mm (1 inch) stem 1J873435072
31.8 mm (1‐1/4 inch) stem 1J873535072
12* Upper Wiper, felt
12.7 mm (1/2 inch) stem 1J872706332
19.1 mm (3/4 inch) stem 1J872806332
25.4 mm (1 inch) stem 1J872906332
31.8 mm (1‐1/4 inch) stem 1J873006332
12* ENVIRO‐SEAL bellows seal upper wiper, felt
Size 4x2 w/ 12.7 mm (1/2 inch) stem 18A0868X012
Sizes 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 18A0870X012
13 Packing follower, 316 stainless steel
13* ENVIRO‐SEAL bellows seal bushing
size 4x2 w/ 12.7 mm (1/2 inch) stem
(2 req'd)
S31600 (316 SST) 18A0820X012
R30006 (alloy 6) 18A0819X012
S31600 chrome coated 11B1155X012
For size 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem (1 req'd)
S31600 (316 SST) 18A0824X012
R30006 (alloy 6) 18A0823X012
S31600 chrome coated 11B1157X012
13* ENVIRO‐SEAL bellows seal bushing/liner
size 4x2 w/ 12.7 mm (1/2 inch) stem
(2 req'd)
N10276 bushing, PTFE/glass liner 12B2713X012
N10276 bushing, PTFE/carbon liner 12B2713X042
For size 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem (1 req'd)
N10276 bushing, PTFE/glass liner 12B2715X012
N10276 bushing, PTFE/carbon liner 12B2715X042
14 Packing Box Pipe Plug
14 Lubricator, steel/440 SST
14 Lubricator/Isolating Valve Assy. pl steel
15 Yoke Locknut, steel
15 ENVIRO‐SEAL bellows seal yoke locknut, steel
16 Pipe Plug for double‐tapped bonnet
For size 4x2 thru 12x6 valve
Steel for WCC steel bonnet
S31600 for chrome moly steel or
316 SST bonnet
For size 10x8 or 12x8 valve
Steel for WCC steel bonnet
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
37
Key Description Part Number
S31600 for chrome moly steel or
316 SST bonnet
16 ENVIRO‐SEAL bellows seal pipe plug
(2 req'd)
20* ENVIRO‐SEAL bellows seal stem/bellows
assembly
1 ply bellows
S31603 (316L SST) trim, N06625
bellows
Size 4x2 w/ 12.7 mm (1/2 inch) stem 32B4226X012
Size 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 32B4228X012
N06022 trim, N06022
bellows
Size 4x2 w/ 12.7 mm (1/2 inch) stem 32B4226X022
Size 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 32B4228X022
20* ENVIRO‐SEAL bellows seal stem/bellows
assembly (cont'd)
2 ply bellows
S31603 (316L SST) trim, N06625
bellows
Size 4x2 w/ 12.7 mm (1/2 inch) stem 32B4226X032
Size 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 32B4228X032
Key Description Part Number
N06022 trim, N06022
bellows
Size 4x2 w/ 12.7 mm (1/2 inch) stem 32B4226X042
Size 6x4x2‐1/2, 6x4, & 8x4
w/ 12.7 mm (1/2 inch) stem 32B4228X042
22* ENVIRO‐SEAL bellows seal bonnet gasket,
graphite/laminate
Size 4x2 valve 12B6318X022
Size 6x4x2‐1/2, 6x4, & 8x4 valve 12B6320X022
24 ENVIRO‐SEAL bellows seal adaptor
25 Cap Screw for 127 mm (5 inch) yoke boss,
steel (8 req'd)
Size 12x8 valve, CL900
26 Hex Nut for 127 mm (5 inch) yoke boss,
pl steel (8 req'd)
27 Pipe Nipple for lubricator/isolating valve
28 Warning Nameplate for ENVIRO‐SEAL bellows
29 Drive Screw for ENVIRO‐SEAL bellows, stain‐
less steel (2 req'd)
36* ENVIRO‐SEAL bellows seal pin, N06022 12B3951X012
37 Warning Tag for ENVIRO‐SEAL bellows
38 Tie for ENVIRO‐SEAL bellows
39 ENVIRO‐SEAL bellows seal thrust ring
Trim S31600
Single PTFE Packing
Size 4x2 w/ 12.7 mm (1/2 inch) stem
(2 req'd)
Keys 6*, 7*, 8, and 10 Packing Box Parts
DESCRIPTION KEY NO.STEM DIAMETER, mm (INCHES)
12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.8 (1‐1/4)
PTFE V‐Ring Packing
Packing Set, PTFE (1 req'd for single, 2req”d for double)(1) 6 1R290201012 1R290401012 1R290601012 1R290801012
Spring, Stainless Steel(for single only)
8 1F125537012 1F125637012 1D582937012 1D387437012
Lantern Ring, Stainless Steel(for double only)
8 1J269335072 0N028435072 0U099735072 0W087135072
Quantity required Double ‐ ‐ ‐ 2 1 1 1
Special washer, Stainless Steel (forsingle only)
10 1F125136042 1F125036042 1H982236042 1H995936042
PTFE/compositionPacking
Packing Ring, PTFE composition 7 1E319001042 1E319101042 1D7518X0012 1D7520X0012
Quantity required Double ‐ ‐ ‐ 10 8 8 8
Lantern Ring, Stainless Steel (1 req'd) 8 1J9623 35072 0N028435072 0U099735072 0W087135072
GraphiteRibbon/Filament
Graphite Ribbon Ring 7 1V3802X0022 1V2396X0022 1U6768X0022 1V5666X0022
Quantity requiredSingle ‐ ‐ ‐ 2 2 2 2
Double ‐ ‐ ‐ 3 3 3 3
Graphite Filament Ring 7 1E3190X0222 1E3191X0282 1D7518X0132 1D7520X0162
Quantity requiredSingle ‐ ‐ ‐ 2 3 3 3
Double ‐ ‐ ‐ 4 5 5 5
Lantern Ring 8 1J962335072 0N028435072 0U099735072 0W087135072
Quantity requiredSingle ‐ ‐ ‐ 3 2 2 2
Double ‐ ‐ ‐ 2 1 1 1
1. Key 6 for double construction contains one extra Lower Wiper for all sizes. Discard upon assembly.
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
38
Figure 21. Typical Fisher Bonnet with Single PTFE V‐Ring Packing Set
APPLY LUB
E0201
30A9425-A
35A3976-A
CU3911-C
42B3947-A ENVIRO-SEALBELLOWS SEAL BONNET
STYLE 1 OR 2EXTENSION BONNET
DETAIL OF NPS 12x8 CL900YOKE BOSS BOLTING
DETAIL OF 5‐INCH (127 mm) YOKEBOSS ACTUATOR BOLTING
PLAIN BONNET
Instruction ManualD100399X012
EW ValveJuly 2017
39
Valve Body (figures 22 through 24)
Note
This parts list provides part numbers for standard valves and valves with
Whisper Trim I cages only. For part numbers for valves with WhisperFlo,
Whisper Trim III, or Cavitrol III cages, contact your Emerson sales office
or Local Business Partner.
Key Description Part Number
1 Valve Body
If you need a valve body as a replacement part, order
by valve size, serial number, and desired material.
2* Valve Plug See following table
3* Cage See following table
4 Cage Adaptor for restricted‐capacity
Size 6x4x2‐1/2 valve
5 Seat Ring Adaptor for restricted‐capacity
Size 6x4x2‐1/2 valve
6* EWD Piston Ring
Class II shutoff minimum (1 req'd)
To 900�F (to 482�C), graphite
Size 4x2 valve 1U2258X0012
Size 6x4x2‐1/2 valve 1U2300X0012
Size 6x4 or 8x4 valve 1U2392X0012
Size 8x6 or 12x6 valve
For all except Whisper Trim III cages 1U5069X0012
Size 10x8 or 12x8 valve 10A3262X022
Optional Class IV shutoff, graphite
Size 6x4 or 8x4 valve (3 req'd)
Standard, to 482�C (to 900�F) 17A3988X012
High‐temp, 482 to 593�C (901 to 1100�F) 17A3988X022
Size 8x6 or 12x6 valve (3 req'd)
For all except Whisper Trim III cages
Standard, 482�C (to 900�F) 17A3990X012
High‐temp, 482 to 593�C
(901 to 1100�F) 17A3990X022
Size 10x8 or 12x8 valve (2 req'd)
Standard, to 482�C (to 900�F) 17A3991X012
High‐temp, 482 to 593�C (901 to 1100�F) 17A3991X022
Key Description Part Number
7* Valve Plug Stem See following table
8* Pin, S31600 (316 SST)
EWD or EWT
12.7 mm (1/2 inch) stem dia 1V322735072
19.1 mm (3/4 inch) stem dia 1V326035072
25.4 mm (1 inch) or 31.8 mm (1‐1/4 inch)
stem dia 1V334035072
EWS
12.7 mm (1/2 inch) stem dia 1B599635072
19.1 mm (3/4 inch) stem dia 1F723635072
25.4 mm (1 inch) or 31.8 mm (1‐1/4 inch)
stem dia 1D269735072
Size 10x8 or 12x8 valve,
31.8 mm (1‐1/4 inch) stem dia 1K249838992
9* Seat Ring See following table
10* thru 14* Gaskets See following table
15 Stud Bolt, steel
Plain, ext style 1, or ext style 2 bonnet
All constructions except 2‐stage Cavitrol III
Size 4x2 valve (8 req'd)
Size 6x4, 6x4x2‐1/2,
or 8x4 valve (8 req'd)
Size 8x6 CL300 or CL600 valve (12 req'd)
Whisper Trim I cage (4‐inch travel)
All other constructions except Whisper I (4‐inch travel),
Whisper III, and 2‐stage Cavitrol III
Size 8x6 CL900 valve (12 req'd)
Size 12x6 valve (12 req'd)
Whisper Trim I cage (4‐inch travel)
All other constructions except Whisper I (4‐inch travel),
Whisper III, and 2‐stage Cavitrol III
Size 10x8 valve (16 req'd)
Size 12x8
CL300 or CL600 valve (16 req'd)
Size 12x8 CL900 valve (12 req'd)
16 Stud Bolt Nut, steel, factory lubricated
Size 4x2 valve (8 req'd)
Size 6x4, 6x4x2‐1/2,
or 8x4 valve (8 req'd)
Size 8x6 CL300 or CL600 valve (12 req'd)
Size 8x6 CL900 valve (12 req'd)
Size 12x6 valve (12 req'd)
Size 10x8 valve (16 req'd)
Size 12x8 valve, CL300 or CL600 (16 req'd)
Size 12x8 CL900 (12 req'd)
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
40
Figure 22. Fisher EWD Valve through NPS 12x6 with Optional Drain Plug
DETAIL OF MULTIPLEPISTON RING FOR
CLASS IV SHUTOFF
RESTRICTED TRIM DETAIL
VALVE ASSEMBLY WITHSTANDARD CAGE
41A9275-B
57A3966‐A
30A9547‐G
FLOW DIRECTION
WHISPER TRIMSTD TRIMCAVITROL TRIM
Instruction ManualD100399X012
EW ValveJuly 2017
41
Key Description Part Number
17 Pipe Plug for drain‐tapped valve
18 Flow Arrow, SST
19 Drive screw, SST (6 req'd)
21* Disk Retainer for PTFE‐seat EWS or EWT
Size 4x2 valve, S31600 1V710835072
Size 6x4x2‐1/2 valve, S31600 1V710935072
Size 6x4 or 8x4 valve, CF8M 1V711533092
Size 8x6 or 12x6 valve, CF8M
For all except Whisper Trim III cages 1V711833092
Size 10x8 or 12x8 valve
CF8M 10A4466X012
R30006 (Alloy 6) 10A4466X022
22* Disk Seat for PTFE‐seat EWS or EWT
Size 4x2 valve
S31600 10A5936X012
S41600 (416 SST) HT 10A5936X072
Size 6x4x2‐1/2 valve, S31600 1V711135072
Size 6x4 valve, CF8M 1V712533092
Size 8x4 valve, S31600 1V712633092
Size 8x6 or 12x6 CL300 or CL600 valve, 316 SST
For all except Whisper Trim III cages
Size 8x6 valve only
51 mm (2 inch) or 76 mm (3 inch) travel 2V721733092
102 mm (4 inch) travel 20A1180X012
Size 12x6 valve only
51 mm (2 inch) or 76 mm (3 inch) travel 2V712733092
102 mm (4 inch) travel 20A1180X012
Size 8x6 CL900 valve, CF8M 21A9344X012
Size 10x8 or 12x8 valve
CF8M 20A4467X012
R30006 20A4467X022
23* Disk for PTFE‐seat EWS or EWT, PTFE
Size 4x2 valve 1V710706242
Size 6x4x2‐1/2 valve 1V711006242
Size 6x4 or 8x4 valve 1V711606242
Size 8x6 or 12x6 valve
For all except Whisper Trim III cages 1V711906242
Size 10x8 or 12x8 valve 20A4468X012
26 Load Ring for Size 10x8 or 12x8 valve only
27* Retaining Ring for spring‐loaded EWT seal rings,
302 SST
All except 2‐stage Cavitrol III construction
Size 4x2 valve 10A4210X012
Size 6x4 or 8x4 valve 10A4225X012
Size 6x4x2‐1/2 valve,
std construction only 10A4219X012
28* EWT 2‐Piece Seal Ring for all except
Cavitrol III constructions
Carbon‐filled PTFE (not used w/ size NPS 12x8 valve)
Size 4x2 valve 1V550805092
Size 6x4x2‐1/2 valve 1V659505092
Size 6x4 or 8x4 valve 1V659905092
Size 8x6 or 12x6 valve
For std, Whisper Trim I cages 1V660105092
Key Description Part Number
Spring‐loaded(1) PTFE for all except 2‐stage Cavitrol III
Size 4x2 valve 10A4206X012
Size 6x4x2‐1/2 valve 10A4215X012
Size 6x4 or 8x4 valve 10A4223X012
Size 8x6 or 12x6 valve
For std and Whisper Trim I cages 10A2643X022
Size 10x8 or 12x8 valve 10A3261X012
29* Backup Ring for EWT 2‐piece seal ring
w/o spring loading
Fluorocarbon(2)
Size 4x2 valve 1V550705292
Size 6x4x2‐1/2 valve 1V659405292
Size 6x4 or 8x4 valve 1V659805292
Size 8x6 or 12x6 valve
For std. Whisper Trim I cages 1V660005292
Ethylene‐Propylene
Size 4x2 valve 1V5507X0042
Size 6x4x2‐1/2 valve 1V6594X0032
Size 6x4 or 8x4 valve 1V6598X0022
Size 8x6 or 12x6 valve
For std, Whisper Trim I cages 1V6600X0022
29* Backup Ring for spring‐loaded EWT seal rings
For all except 2‐stage Cavitrol III constructions
Size 4x2 valve, S41600 10A4208X012
Size 6x4x2‐1/2 valve, S41600 10A4217X012
Size 6x4 or 8x4 valve, S41600 10A4224X012
For Whisper III constructions only
Size 8x6 or 12x6 valve
S41600 12A3332X012
S31600 12A3332X022
31* Cage Retainer, required for Whisper Trim III and Cavitrol III cages
only. See your Emerson Automation Solutions sales office.
32 Bonnet Spacer
51 Anti‐seize lubricant (not furnished)
52 Cage Spacer
53* Shim See following table
55 Wire
C‐seal Trim (figure 9)2* Plug/Retainer see following table
3* Cage see following table
7* Valve Plug Stem, S20910 see following table
9* Seat Ring see following table
64* C‐seal, N07718 see following table
TSO Trim (figures 7 and 8)3* Cage See following table
9* Seat Ring See following table
2* Plug/Stem Assembly See following table
28* Seal Ring See following table
63* Anti‐Extrusion Ring See following table
29* Back Up Ring See following table
27* Retaining Ring See following table
*Recommended spare parts1. Spring is N06022.2. Not for steam or water above 82�C (180�F).
Instruction ManualD100399X012
EW ValveJuly 2017
42
Figure 23. Fisher EWS Valve through NPS 12x6FLOW DIRECTION
CAVITROL TRIM
STD TRIMWHISPER TRIM
COMPLETE VALVE ASSEMBLY WITH METAL SEAT WITH OPTIONAL DRAIN PLUG
ELASTOMERIC SEAT DETAIL
31A9274‐C
Instruction ManualD100399X012
EW ValveJuly 2017
43
Figure 24. Typical Fisher EWT Valve Assemblies
VIEW AFLOW UP
VIEW AFLOW DOWN
47.6 TO 136.5 mm (1.875 TO 5.375 INCH)PORT DIAMETERS
FLOW DIRECTION
WHISPER TRIM STD TRIMCAVITROL TRIM
178 mm (7 INCH) AND 203 mm (8 INCH)PORT DIAMETER
NPS 4x2 THROUGH 12x6 VALVEWITH STANDARD CAGE AND METAL SEAT
WITH OPTIONAL DRAIN PLUG
NPS 12x8 VALVEWITH STANDARD CAGE
DETAIL OF PTFE SEAT AND VALVE PLUGWITH 2‐PIECE SEAL RING
DETAILS OF VALVE PLUG WITHSPRING‐LOADED SEAL RING
APPLY LUB
43A8590‐B
55A8288‐B
43A8592‐B
A2069‐2
43A8590‐B
43A8590‐BCORRECT SPRING‐LOADED SEAL
RING ORIENTATION
Instruction ManualD100399X012
EW ValveJuly 2017
44
Figure 25. FGM Gasket Detail with Optional Drain Plug
FULL‐CAPACITY TRIM DETAIL
FGM GASKETS ALSO MUST BEINSTALLED WHERE REQUIREDIN SEAT RING AREA PERFIGURE 22, 23, OR 24
RESTRICTED‐TRIM DETAIL
A2713*
Instruction ManualD100399X012
EW ValveJuly 2017
45
Figure 26. NPS 4x2 Through 12x8 Fisher Valves with 1‐Stage Cavitrol III Cage
VIEW ANPS 4x2 THROUGH 8x4
VALVES
APPLY LUB
VIEW ANPS 8x6 THROUGH 12x6
VALVES VIEW A
NPS 12x8 VALVE
NPS 4x2 THROUGH 12x6 VALVESWITH OPTIONAL DRAIN PLUG 58A1015‐A
58A1012‐B
58A1012‐B54A8146‐B
FLOW DIRECTION
NOTES: NOT REQUIRED ON NPS 8x6 AND 12x6 VALVES. KEYS 2, 7, & 8 ARE SUPPLIED AS AN ASSEMBLY (KEY 2)FOR NPS 8x6 AND 12x6 VALVES. NOT REQUIRED FOR NPS 12x8 VALVES WITH 4‐ OR6‐INCH TRAVEL.
12
3
NPS 8x6 CL900VALVE GASKETING DETAIL
WITH OPTIONAL DRAIN PLUG54A8142‐A
FLOW DIRECTION
VIEW A
Instruction ManualD100399X012
EW ValveJuly 2017
46
Figure 27. NPS 4x2 Through 12x8 Fisher Valves with 2‐Stage Cavitrol III Cage
VIEW A
NPS 12x8 VALVE
NPS 4x2 THROUGH 12x6 VALVESWITH OPTIONAL DRAIN PLUG
FLOW DIRECTION
VIEW A
NPS 8x6 CL900VALVE GASKETING DETAIL
WITH OPTIONAL DRAIN PLUG
APPLY LUB
54A7497‐B
54A7495‐A
55A8886‐A
Instruction ManualD100399X012
EW ValveJuly 2017
47
Figure 28. Typical Fisher EWD Valve with Whisper Trim III Cage
COMPLETE VALVE ASSEMBLY WITH WHISPER TRIM III CAGE,SINGLE GRAPHITE PISTON RING, AND OPTIONAL DRAIN PLUG
FLOW DIRECTION
52A3328‐C
30A9547‐G
Instruction ManualD100399X012
EW ValveJuly 2017
48
Figure 29. Typical Fisher WhisperFlo Trims
DISK SEAT
EWD/EWT(METAL SEAT)
EWT(SOFT SEAT)
DISKDISK RETAINER
WhisperFlo CAGE
CAGE RETAINER
BONNET SPACER
SEAT RING
SEAT RING
DISK SEATDISKDISK RETAINER
WhisperFlo CAGE
CAGE RETAINER
BONNET SPACER
EWD CLASS IV(METAL SEAT)
EWT WITHSPRING‐LOADED SEAL RING
(SOFT SEAT)
Instruction ManualD100399X012
EW ValveJuly 2017
49
Key 2* Fisher EWD Valve Plug
VALVE SIZE, NPS MATERIALSTEM DIA, mm (INCH)
12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.8 (1‐1/4)
4 x 2(for 1 piston ring only)
Hardened S41600 (416 SST) 1V657546172 1V657646172 ‐ ‐ ‐ ‐ ‐ ‐
S31600 (316 SST) 1V657535072 1V657635072 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5326X012 11A5327X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 11A5328X012 11A5329X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 x 2‐1/2(for 1 piston ring only)
Hardened S41600 1V657746172 1V657846172 ‐ ‐ ‐ ‐ ‐ ‐
S31600 1V657735072 1V657835072 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5332X012 11A5333X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 11A5334X012 11A5335X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 or 8 x 4
For 1 piston ring
Hardened S41600 1V658146172 1V658246172 1V658346172 ‐ ‐ ‐
S31600 1V658135072 1V658235072 1V658335072 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5344X012 11A5345X012 11A5346X012 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 11A5347X012 11A5348X012 11A5349X012 ‐ ‐ ‐
For 3 piston rings
Hardened S41600 27A3932X012 27A3933X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600 27A3932X012 27A3933X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 27A3938X012 27A3939X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 27A3941X012 27A3942X012 ‐ ‐ ‐ ‐ ‐ ‐
8 x 6 or 12x 6,except forWhisperTrim IIIcages
51 or76 mm(2 or 3inch)travel
For 1 piston ring
Hardened S41600 ‐ ‐ ‐ 1V658446172 1V658546172 1V658646172
S31600 ‐ ‐ ‐ 1V658435072 1V658535072 1V658635072
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A5351X012 20A0103X012 20A4608X012
S31600/CoCr‐A on seat and guide(2) ‐ ‐ ‐ 21A5353X012 21A5354X012 21A5355X012
For 3 piston rings
Hardened S41600 ‐ ‐ ‐ 27A3944X012 27A3945X012 ‐ ‐ ‐
S31600 ‐ ‐ ‐ 27A3944X022 27A3945X022 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 27A3950X012 27A3951X012 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) ‐ ‐ ‐ 27A3953X012 27A3954X012 ‐ ‐ ‐
10 x 8 or 12 x 8
For 1 piston ring
Hardened S41600 ‐ ‐ ‐ 21A5356X012 21A5357X012 21A5358X012
S31600 ‐ ‐ ‐ 21A5356X022 21A5357X022 21A5358X022
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A5362X012 21A5363X012 21A5364X012
S31600/CoCr‐A on seat and guide(2) ‐ ‐ ‐ 21A5365X012 21A5366X012 21A5367X012
For 2 piston rings
Hardened S41600 ‐ ‐ ‐ 27A3956X012 27A3957X012 ‐ ‐ ‐
S31600 ‐ ‐ ‐ 27A3956X022 27A3957X022 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 27A3962X012 27A3963X012 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) ‐ ‐ ‐ 27A3965X012 27A3966X012 ‐ ‐ ‐
1. Not for use with CB7CU‐1 (17‐4PH SST) cages above 210�C (410�F) or R30006 (Alloy 6) cages above 427�C (800�F).2. High‐temperature material (identified by an H stamped on top of the plug) for use with CB7CU‐1 cages above 210�C (410�F) or R30006 cages above 427�C (800�F).
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
50
Key 2* Fisher EWS Valve Plug
VALVE SIZE, NPS MATERIALSTEM DIA, mm (INCH)
12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.8 (1‐1/4)
4 x 2
Hardened S41600 (416 SST) 11A5214X012 11A5215X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600 (316 SST) 11A5214X022 11A5215X022 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5218X012 11A5219X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 11A5220X012 11A5221X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 x 2‐1/2
Hardened S41600 11A5222X012 11A5223X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600 11A5222X022 11A5223X022 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5226X012 11A5227X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 11A5228X012 11A5229X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 or 8 x 4
Hardened S41600 11A5238X012 11A5239X012 11A5240X012 ‐ ‐ ‐
S31600 11A5238X022 11A5239X022 11A5240X022 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5244X012 11A5245X012 11A5246X012 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(2) 11A5247X012 11A5248X012 11A5249X012 ‐ ‐ ‐
8 x 6 or 12 x 6Except for
Whisper Trim IIIcages
Hardened S41600 ‐ ‐ ‐ 11A5250X012 11A5251X012 11A5252X012
S31600 ‐ ‐ ‐ 11A5250X022 11A5251X022 11A5252X022
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 11A5256X012 11A5257X012 11A5258X012
S31600/CoCr‐A on seat and guide(2) ‐ ‐ ‐ 11A5259X012 11A5260X012 11A5261X012
10 x 8 or 12 x 8
Hardened S41600 ‐ ‐ ‐ 21A5262X012 21A5263X012 21A5264X012
S31600 ‐ ‐ ‐ 21A5262X012 21A5263X012 21A5264X012
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A5268X012 21A5269X012 21A5270X012
S31600/CoCr‐A on seat and guide(2) ‐ ‐ ‐ 21A5271X012 21A5272X012 21A5273X012
1. Not for use with CB7CU‐1 (17‐4PH SST) cages above 210�C (410�F) or R30006 (Alloy 6) cages above 427�C (800�F).2. High‐temperature material (identified by an H stamped on top of the plug) for use with CB7CU‐1 cages above 210�C (410�F) or R30006 cages above 427�C (800�F).
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
51
Key 2* Valve Plug for Fisher EWT with Two‐Piece Seal Ring
VALVE SIZE, NPS MATERIALSTEM DIA, mm (INCH)
12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.8 (1‐1/4)
4 x 2
Hardened S41600 (416 SST) 1V657546172 1V657646172 ‐ ‐ ‐ ‐ ‐ ‐
S31600 (316 SST) 1V657535072 1V657635072 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5326X012 11A5327X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 x 2‐1/2
Hardened S41600 1V657746172 1V657846172 ‐ ‐ ‐ ‐ ‐ ‐
S31600 1V657735072 1V657835072 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5332X012 11A5333X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 or 8 x 4
Hardened S41600 1V658146172 1V658246172 1V658346172 ‐ ‐ ‐
S31600 1V658135072 1V658235072 1V658335072 ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) 11A5344X012 11A5345X012 11A5346X012 ‐ ‐ ‐
8 x 6 or 12 x 6,except for
Whisper Trim III cages
For 51 or 76mm
(2 or 3 inch)travel
Hardened S41600 ‐ ‐ ‐ 1V658446172 1V658546172 1V658646172
S31600 ‐ ‐ ‐ 1V658435072 1V658535072 1V658635072
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A5351X012 20A0103X012 204608X012
For 102 mm(4 inch)
travel
Hardened S41600 ‐ ‐ ‐ 11A2622X012 ‐ ‐ ‐ ‐ ‐ ‐
S31600 ‐ ‐ ‐ 11A2622X022 ‐ ‐ ‐ ‐ ‐ ‐
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A8128X012 ‐ ‐ ‐ ‐ ‐ ‐
1. Not for use with CB7CU‐1 (17‐4PH SST) cages above 210�C (410�F).
Key 2* Valve Plug for Spring‐Loaded Fisher EWT Seal Ring (except for Cavitrol III constructions)
VALVE SIZE, NPS MATERIALSTEM DIA, mm (INCH)
12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.8 (1‐1/4)
4 X 2 Hardened S41600 (416 SST) 20A4097X012 20A4098X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 x 2‐1/2 Hardened S41600 20A9533X012 20A4144X012 ‐ ‐ ‐ ‐ ‐ ‐
6 x 4 or 8 x 4 Hardened S41600 20A2641X012 20A4194X012 20A4195X012 ‐ ‐ ‐
8 x 6 or 12 x 6, except forWhisper Trim III cages
Hardened S41600 ‐ ‐ ‐ 20A2642X012 20A5621X012 20A7343X012
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A8443X012 20A6706X012 ‐ ‐ ‐
10 x 8 or 12 x 8
Hardened S41600 ‐ ‐ ‐ 21A5356X012 21A5357X012 21A5358X012
S31600 ‐ ‐ ‐ 21A5356X022 21A5357X022 21A5358X022
S31600/CoCr‐A on seat and guide(1) ‐ ‐ ‐ 21A5362X012 21A5363X012 21A5364X012
1. Not for use with CB7CU‐1 (17‐4PH SST) cages above 210�C (410�F).
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
52
C‐seal Parts for Fisher EWD Valve (Keys 3*, 2*, 9*, 64*, 6*, and 7*)VALVE
SIZEPORTDIA
TRAVEL
TRIM
STEMDIA CHARACTER‐
ISTIC
CAGEPLUG/
RETAINERSEAT RING C‐seal PISTON RING STEM
NPS Inch Inchmm
(Inch)Key 3 Key 2 Key 9 Key 64 Key 6 Key 7
6X4 4.375 2
1
12.7(1/2)
Linear 34B5346X022
37B2279X012 23B6129X012 23B9197X012 14B5341X0121U2305X0142(1)
1U2306X0192(2)Equal % 37B3194X012
Whisper I 34B9852X012
19.1(3/4)
Linear 34B5346X022
37B2279X022 23B6129X012 23B9197X012 14B5341X0121K5877X0132(1)
1U4446X0102(2)Equal % 37B3194X012
Whisper I 34B9852X012
25.4(1)
Linear 34B5346X022
37B2279X032 23B6129X012 23B9197X012 14B5341X0121K7796X0062(1)
1K7891X0242(2)Equal % 37B3194X012
Whisper I 34B9852X012
3H
12.7(1/2)
Linear 34B5346X012
34B5345X032 23B6150X012 23B9197X012 14B5341X0121U2305X0142(1)
1U2306X0192(2)Equal % 37B3194X022
Whisper I ‐ ‐ ‐
19.1(3/4)
Linear 34B5346X012
34B5345X012 23B6150X012 23B9197X012 14B5341X0121K5877X0132(1)
1U4446X0102(2)Equal % 37B3194X022
Whisper I ‐ ‐ ‐
25.4(1)
Linear 34B5346X012
34B5345X022 23B6150X012 23B9197X012 14B5341X0121K7796X0062(1)
1K7891X0242(2)Equal % 37B3194X022
Whisper I ‐ ‐ ‐
37H
12.7(1/2)
Linear 34B5346X022
34B5345X032 23B6150X012 23B9197X012 14B5341X0121U2305X0142(1)
1U2306X0192(2)Equal % 37B3194X012
Whisper I 34B9852X012
19.1(3/4)
Linear 34B5346X022
34B5345X012 23B6150X012 23B9197X012 14B5341X0121K5877X0132(1)
1U4446X0102(2)Equal % 37B3194X012
Whisper I 34B9852X012
25.4(1)
Linear 34B5346X022
34B5345X022 23B6150X012 23B9197X012 14B5341X0121K7796X0062(1)
1K7891X0242(2)Equal % 37B3194X012
Whisper I 34B9852X012
8X4 4.375 2
1
12.7(1/2)
Linear 34B5346X022
37B2279X012 23B6130X012 23B9197X012 14B5341X0121U2305X0142(1)
1U2306X0192(2)Equal % 37B3194X012
Whisper I 34B9852X012
19.1(3/4)
Linear 34B5346X022
37B2279X022 23B6130X012 23B9197X012 14B5341X0121K5877X0132(1)
1U4446X0102(2)Equal % 37B3194X012
Whisper I 34B9852X012
25.4(1)
Linear 34B5346X022
37B2279X032 23B6130X012 23B9197X012 14B5341X0121K7796X0062(1)
1K7891X0242(2)Equal % 37B3194X012
Whisper I 34B9852X012
3H
12.7(1/2)
Linear 34B5346X012
34B5345X032 23B6130X032 23B9197X012 14B5341X0121U2305X0142(1)
1U2306X0192(2)Equal % 37B3194X022
Whisper I ‐ ‐ ‐
19.1(3/4)
Linear 34B5346X012
34B5345X012 23B6130X032 23B9197X012 14B5341X0121K5877X0132(1)
1U4446X0102(2)Equal % 37B3194X022
Whisper I ‐ ‐ ‐
25.4(1)
Linear 34B5346X012
34B5345X022 23B6130X032 23B9197X012 14B5341X0121K7796X0062(1)
1K7891X0242(2)Equal % 37B3194X022
Whisper I ‐ ‐ ‐
1. For Standard Bonnet.2. For Style 1 Extension Bonnet.
‐continued‐
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
53
C‐seal Parts for Fisher EWD Valve (Keys 3*, 2*, 9*, 64*, 6*, and 7*) (continued)VALVE
SIZEPORTDIA
TRAVEL
TRIM
STEMDIA CHARACTER‐
ISTIC
CAGEPLUG/
RETAINERSEAT RING C‐seal PISTON RING STEM
NPS Inch Inchmm
(Inch)Key 3 Key 2 Key 9 Key 64 Key 6 Key 7
8X4 4.375 2 37H
12.7(1/2)
Linear 34B5346X022
34B5345X032 23B6130X032 23B9197X012 14B5341X0121U2305X0142(1)
1U2306X0192(2)Equal % 37B3194X012
Whisper I 34B9852X012
19.1(3/4)
Linear 34B5346X022
34B5345X012 23B6130X032 23B9197X012 14B5341X0121K5877X0132(1)
1U4446X0102(2)Equal % 37B3194X012
Whisper I 34B9852X012
25.4(1)
Linear 34B5346X022
34B5345X022 23B6130X032 23B9197X012 14B5341X0121K7796X0062(1)
1K7891X0242(2)Equal % 37B3194X012
Whisper I 34B9852X012
8X6 7 2
1
19.1(3/4)
Linear 33B9178X012
33B9195X012 20B0811X012 23B9182X012 13B9176X0121K5877X0132(1)
1U4446X0102(2)Equal % 34B3628X012
Whisper I ‐ ‐ ‐
25.4(1)
Linear 33B9178X012
33B9195X022 20B0811X012 23B9182X012 13B9176X0121N7047X0052(1)
1L8776X0032(2)Equal % 34B3628X012
Whisper I ‐ ‐ ‐
3H
19.1(3/4)
Linear ‐ ‐ ‐
34B7699X022 33B8104X012 23B9182X012 13B9176X0121K5877X0132(1)
1U4446X0102(2)Equal % ‐ ‐ ‐
Whisper I 34B9828X012
25.4(1)
Linear ‐ ‐ ‐
34B7699X012 33B8104X012 23B9182X012 13B9176X0121N7047X0052(1)
1L8776X0032(2)Equal % ‐ ‐ ‐
Whisper I 34B9828X012
37H
19.1(3/4)
Linear 33B9178X012
34B7699X022 33B8104X012 23B9182X012 13B9176X0121K5877X0132(1)
1U4446X0102(2)Equal % 34B3628X012
Whisper I ‐ ‐ ‐
25.4(1)
Linear 33B9178X012
34B7699X012 33B8104X012 23B9182X12 13B9176X0121N7047X0052(1)
1L8776X0032(2)Equal % 34B3628X012
Whisper I ‐ ‐ ‐
12X6 7 2
1
19.1(3/4)
Linear 33B9178X012
33B9195X012 33B6131X012 23B9182X012 13B9176X0121K5877X0132(1)
1U4446X0102(2)Equal % 34B3628X012
Whisper I 34B9828X022
25.4(1)
Linear 33B9178X012
33B9195X022 33B6131X012 23B9182X012 13B9176X0121N7047X0052(1)
1L8776X0032(2)Equal % 34B3628X012
Whisper I 34B9828X022
3H
19.1(3/4)
Linear 33B9178X022
34B7699X022 33B6133X012 23B9182X012 13B9176X0121K5877X0132(1)
1U4446X0102(2)Equal % 34B3628X022
Whisper I 34B9828X012
25.4(1)
Linear 33B9178X022
34B7699X012 33B6133X012 23B9182X012 13B9176X0121N7047X0052(1)
1L8776X0032(2)Equal % 34B3628X022
Whisper I 34B9828X012
37H
19.1(3/4)
Linear 33B9178X012
34B7699X022 33B6133X012 23B9182X012 13B9176X0121K5877X0132(1)
1U4446X0102(2)Equal % 34B3628X012
Whisper I 34B9828X022
25.4(1)
Linear 33B9178X012
34B7699X012 33B6133X012 23B9182X012 13B9176X0121N7047X0052(1)
1L8776X0032(2)Equal % 34B3628X012
Whisper I 34B9828X012
1. For Standard Bonnet.2. For Style 1 Extension Bonnet.3. Requires bonnet spacer 34B1369.
‐continued‐
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
54
C‐seal Parts for Fisher EWD Valve (Keys 3*, 2*, 9*, 64*, 6*, and 7*) (continued)VALVE
SIZEPORT
DIATRAVEL
TRIM
STEMDIA CHARACTER‐
ISTIC
CAGEPLUG/
RETAINERSEAT RING C‐seal PISTON RING STEM
NPS Inch Inchmm
(Inch)Key 3 Key 2 Key 9 Key 64 Key 6 Key 7
10X8 8
3 1
19.1(3/4)
Linear 37B1663X02237B6392X022 29A9704X012 34B9827X012 24B9826X012 1K5880X0262(1)
Equal % 37B5635X022
25.4(1)
Linear 37B1663X02237B6392X012 29A9704X012 34B9827X012 24B9826X012 10A3282X222(2)
Equal % 37B5635X022
2
1
25.4(1)
Whisper I 47B6378X01237B6389X012 29A9704X012 34B9827X012 24B9826X012
10A3282X222(2)
3.5(3) Whisper I 47B5214X012 1K7783X0032(2)
2 31.8(1‐1/4)
Whisper I 47B6378X01237B6379X012 29A9704X012 34B9827X012 24B9826X012
10A6073X072(2)
3.5(3) Whisper I 47B5214X012 ‐ ‐ ‐(2)
3 3H
19.1(3/4)
Linear 37B1663X01237B1665X032 29A9704X022 34B9827X012 24B9826X012 1K5880X0262(1)
Equal % 37B5635X012
25.4(1)
Linear 37B1663X01237B1665X012 29A9704X022 34B9827X012 24B9826X012 10A3282X222(2)
Equal % 37B5635X012
31.8(1‐1/4)
Linear 37B1663X01237B1665X022 29A9704X022 34B9827X012 24B9826X012 1L2298X0202(2)
Equal % 37B5635X012
10X8 8
3
37H
19.1(3/4)
Linear 37B1663X02237B1665X032 29A9704X022 34B9827X012 24B9826X012 1K5880X0262(1)
Equal % 37B5635X022
25.4(1)
Linear 37B1663X02237B1665X012 29A9704X022 34B9827X012 24B9826X012 10A3282X222(2)
Equal % 37B5635X022
31.8(1‐1/4)
Linear 37B1663X02237B1665X022 29A9704X012 34B9827X012 24B9826X012 1L2298X0202(2)
Equal % 37B5635X022
2 25.4(1)
Whisper I 47B6378X01234B9848X012 29A9704X012 34B9827X012 24B9826X012
10A3282X222(2)
3.5(3) Whisper I 47B5214X012 1K7783X0032(2)
2 31.8(1‐1/4)
Whisper I 47B6378X012‐ ‐ ‐ 29A9704X012 34B9827X012 24B9826X012
10A6073X072(2)
3.5(3) Whisper I 47B5214X012 ‐ ‐ ‐(2)
12X8 8 3 3H
25.4(1)
Linear 37B1663X01237B1665X012 29A9704X022 34B9827X012 24B9826X012 10A3282X222
Equal % 37B5635X012
31.8(1‐1/4)
Linear 37B1663X01237B1665X022 29A9704X022 34B9827X012 24B9826X012 10A3282X222
Equal % 37B5635X012
1. For Standard Bonnet.2. For Style 1 Extension Bonnet.3. Requires bonnet spacer 34B1369.
TSO Parts for Fisher EWT Valve (Keys 3*, 9*, 2*, 28*, 63*, 29*, and 27*)(1)
VALVESIZE
PORTDIA
STEMDIAMETER CHARAC‐
TERISTIC
CAGE SEAT RINGPLUG/
STEM ASSYSEAL RING
ANTI‐EXTRING
BACKUP RINGRETAINING
RING
NPS Inch mm Inch Key 3 Key 9 Key 2 Key 28 Key 63 Key 29 Key 27
6x4 4.1875 19.1 3/4
Linear 2U236633272
38B0278X012 38B0282X012 10A4223X142 21B9341X012 10A4224X012 10A4225X012Equal % 2U236333272
Quick Open 2U236033272
Whisper 23A8915X032
8x4 4.1875 19.1 3/4
Linear 2U236633272
38B0279X012 38B0282X012 10A4223X142 21B9341X012 10A4224X012 10A4225X012Equal % 2U236333272
Quick Open 2U236033272
Whisper 23A8915X032
8x6 6.8125 19.1 3/4
Linear 2U505933272
38B0280X012 38B0284X012 10A2643X112 22B5998X012 12B5997X012 14A4652X012Equal % 2U506133272
Quick Open 2U506333272
Whisper 23A8913X032
12x6 6.8125 19.1 3/4
Linear 2U505933272
38B0281X012 38B0284X012 10A2643X112 22B5998X012 12B5997X012 14A4652X012Equal % 2U506133272
Quick Open 2U506333272
Whisper 23A8913X032
1. Travel is 2‐Inch. Trim is 812.
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
55
Key 3* Cage (except for Whisper Trim III and Cavitrol III constructions)
Valve Size, NPS Cage StyleStandard
Stainless Steel(1)
CF8M (316 SST), Electroless
Nickel Coating
R30006 (Alloy 6)
4x2
Quick‐opening 2U223433272 2U740448932 2U223439102
Equal percentage 2U223733272 2U741048932 2U223739102
Linear 2U224033272 2U741648932 2U224039102
Whisper Trim I 2V502533272 ‐ ‐ ‐ 2V5025X0012
6x4x2‐1/2
Quick‐opening 2U227633272 2U740548932 2U227639102
Equal percentage 2U227933272 2U741148932 2U227939102
Linear 2U228233272 2U741748932 2U228239102
Whisper Trim I 2V502633272 2V503348932 2V5026X0012
6x4 or 8x4
Quick‐opening 2U236033272 2U740748932 2U236039102
Equal percentage 2U236333272 2U741348932 2U236339102
Linear 2U236633272 2U741948932 2U236639102
Whisper Trim I 23A8915X032 ‐ ‐ ‐ 23A8915X012
8x6 or 12x6,except forWhisper Trim IIIcages
Quick‐opening 2U506333272 2U8069 2U506339102
Equal percentage 2U505933272 2U8067 2U505939102
Linear 2U506133272 2U8068 2U506139102
Whisper Trim I
51 mm (2 inch) travel 23A8913X032 ‐ ‐ ‐ 23A8913X012
102 mm(4 inch) travel
NPS 8x6 valve 23A7190X012 ‐ ‐ ‐ 23A7190X022
NPS 12x6 valve 23A7191X012 ‐ ‐ ‐ 23A7191X022
10x8 or 12x8
Quick‐opening 20A3249X012 20A5469X012 20A3249X092
Equal percentage 20A3245X012 20A5467X012 20A3245X092
Linear 20A3247X012 20A5468X012 20A3247X092
Whisper Trim I, NPS 10x8 valve only, 102 mm (4‐inch) travel 43B7381X012 ‐ ‐ ‐ ‐ ‐ ‐
1. Standard stainless steel is CB7CU‐1 (S17400 H900). S41600 (416 SST) is standard for Whisper Trim III cages in NPS 8X6 and NPS 12X6 with 5.375 inch port.
Actuator Groups (by Type Number)Group 1
54 mm (2‐1/8 inches),71 mm (2‐13/16 inches)
or 90 mm (3‐9/16 inches) Yoke Boss
Group 100127 mm (5 inches)
Yoke Boss
Group 101127 mm (5 inches)
Yoke Boss
Group 40390.5 mm (3‐9/16 inches)
Yoke Boss
585C Series—50.8 mm (2 inches) travel 585C 667 585C
472 & 473 472 1008
657 & 667—76.2 mm (3 inches) travel 473
1008—71.4 mm (2‐13/16 inches) yoke boss 657
1008
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
56
Key 7* Valve Stem (except for Cavitrol III constructions)
VALVE SIZE, NPS
STEM DIA ACTU‐ATOR
GROUP
BONNET
Plain Style 1 ExtensionStyle 2
Extension
mm InchS31600
(316 SST)S31600 Cr Pl(1) S31600
S31600 Cr Pl(1) S31600
4x212.7 1/2 1 1K586935162 1K586946592 1U226335162 1U226346592 1U226435162
19.1 3/4 1 1U226535162 1U226546592 1L400135162 1L400146592 ‐ ‐ ‐
6x4x2‐1/212.7 1/2 1 1P669335162 1P669346592 1K587335162 1K587346592 1V782535162
19.1 3/4 1 1K587735162 1K587746592 1V782435162 1V782446592 1V240035162
6x4 or 8x4
12.7 1/2 1 1U230535162 1U230546592 1U230635162 1U230646592 1U230735162(3)
19.1 3/4 1 1K587735162 1K587746592 1U444635162 1U444646592 1U240035162
25.4 1 100 1U217535162 1U217546592 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 101 1K759035162 1K759046592 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
8x6CL300orCL600,exceptforWhisperTrim IIIcages
51 mm(2‐Inch)travel
19.1 3/4 1 1L996435162 1L996446592 1U507135162 1U507146592 1U524435162
25.4 1 100 1N704735162 1N704746592 1K785135162 1K785146592 ‐ ‐ ‐
25.4 1 101 1K759135162 1K759146592(3) 1P597335162(3) 1P597346592(3) ‐ ‐ ‐
31.8 1‐1/4 100 1K415435162 1K415446592 1R562435162 1R562446592 ‐ ‐ ‐
31.8 1‐1/4 101 1K775335162 1K775346592 1U316235162 1U316246592
76 mm(3‐Inch)travel
19.1 3/4 1 1U293835162 ‐ ‐ ‐ 1U928235162 ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 100, 101 1N704735162 1N704746592 1K785135162 1K785146592 ‐ ‐ ‐
31.8 1‐1/4 100, 101 1K415435162 1K415446592 1N770735162 ‐ ‐ ‐ ‐ ‐ ‐
102 mm(4‐Inch)travel
19.1 3/4 1, 403 1U294135162 ‐ ‐ ‐ 10A9265X552 ‐ ‐ ‐ 10A9265X562
8x6CL900
51 mm(2‐Inch)travel
19.1 3/4 1 1K588035162 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 100 1K778335162 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 1011L2687X0012(2) ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
1N325635162(3) ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4100 1U9886X0012 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
101 1U316235162 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
76 mm(3‐Inch)travel
19.1 3/4 1 1K588035162 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 100, 101 1N325635162 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4 100, 101 1U316235162 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
12x6exceptforWhisperTrim IIIcages
51 or76 mm(2 or3‐Inch)travel
19.1 3/4 1 1L996435162 1L996446592 1U507135162 1U507146592 1U524435162
25.4 1100 1N704735162 1N704746592 1K785135162 1K785146592 ‐ ‐ ‐
101 1K759135162 1K759146592 1P597335162(4) 1P597346592(4) ‐ ‐ ‐
31.8 1‐1/4100 1K415435162 1K415446592 1R562435162 1R562446592 ‐ ‐ ‐
101 1K775335162 1K775346592 1U316235162 1U316246592 ‐ ‐ ‐
102 mm(4‐Inch)travel
19.1 3/4 1, 403 1U294135162 ‐ ‐ ‐ 10A9265X552 ‐ ‐ ‐ 10A9265X562
10x8
51 mm(2‐Inch)travel
19.1 3/4 1 1K588035162 1K5880X0262 1U928235162 1U9282X0192 ‐ ‐ ‐
25.4 1 100 1K7891X0012 ‐ ‐ ‐ 1K7891X0012 ‐ ‐ ‐ ‐ ‐ ‐
76 mm(3‐Inch)travel
25.4 1 100, 101 10A3282X012 ‐ ‐ ‐ 10A3282X012 ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4 100 1L2298X0012 ‐ ‐ ‐ 1L2298X0012 ‐ ‐ ‐ ‐ ‐ ‐
‐continued‐
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
57
Key 7* Valve Stem (except for Cavitrol III constructions) (continued)
VALVE SIZE, NPS
STEM DIA ACTU‐ATOR
GROUP
BONNET
Plain Style 1 ExtensionStyle 2
Extension
mm InchS31600
(316 SST)S31600 Cr Pl(1) S31600
S31600 Cr Pl(1) S31600
12x8, CL300or CL600
51 mm(2‐Inch)
travel
19.1 3/4 1 10A9265X882 ‐ ‐ ‐ 1L818235162 ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 100 11A3429X452 ‐ ‐ ‐ 11A3429X452 ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4 100 1V2092X0032 ‐ ‐ ‐ 1V2092X0032 ‐ ‐ ‐ ‐ ‐ ‐
76 mm(3‐Inch)
travel
25.4 1 100, 101 1L294135162 ‐ ‐ ‐ 1L294135162 ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4 100, 101 11A3430X012 ‐ ‐ ‐ 11A3430X012 ‐ ‐ ‐ ‐ ‐ ‐
12x8, CL900
51 mm(2‐Inch)
travel
19.1 3/4 1 10A9265XB52 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
25.4 1 100 11A3429XA92 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4 100 11A3430X362 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
76 mm(3‐Inch)
travel
25.4 1 100, 101 11A3429XA82 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
31.8 1‐1/4 100, 101 11A3430X622 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
1. Use when temperatures are over 427�C (800�F).2. For EWD with multipiston ring.3. Not for EWD with multipiston ring.4. Not for 51 mm (2‐Inch) travel EWD with multipiston ring.
Key 9* Metal‐Seat Seat Ring (except for Cavitrol III constructions)
VALVE SIZE, NPS
MATERIAL
S41600(416 SST)
CF8M(316 SST)
CF8M/CoCr‐A(316 SST)
4x2 10A5935X012 10A5935X022(2) 10A5935X032(3)
6x4 1V676446172 1V676433092 2V676546062(5)
6x4x2‐1/2 1U222746172 1U222735072(2) 1U222739102(3)
8x4 1V642346172 1V642333092(2) 2V642446062(4)
8x6,CL300 or CL600
Except for Whisper Trim III cages
51 mm (2‐Inch) travel 2V721546172(1) 2V721533092 2V721646062
76 mm (3‐Inch) or 102 mm (4‐Inch) travel
2V9406X00B2(1) 2V9406X00A2 20A1181X012
8x6CL900
51 mm (2‐Inch) travel 21A8231X012(1) ‐ ‐ ‐ 21A9343X012(4)
76 mm (3‐Inch) travel 21A9345X012(1) ‐ ‐ ‐ 21A9346X012
12x6 Except forWhisper Trim III cages
51 mm (2‐Inch) travel 2V643946172 2V643933092 2V644046062
76 mm (3‐Inch) travel 20A6345X012 20A6345X022 ‐ ‐ ‐
102 mm (4‐Inch) travel 2V9406X00B2(1) 2V9406X00A2 20A1181X012
10x8 or 12x8 20A3260X012(1) 20A3260X022 20A3260X152(1)
1. CA15 is substituted for this construction.2. S31600 (316 SST) is substituted for this construction.3. R30006 is substituted for this construction.4. S31600/CoCr‐A is substituted for this construction.5. S31600/CoCr‐A hard faced seat ring.
Gasket Descriptions
KEY NUMBER DESCRIPTION
MATERIAL
FGM-198 TO 593�C
(-325 TO 1100�F)
10 Bonnet Gasket
Graphite/S3160011 Cage Gasket
13 Seat Ring or Liner Gasket
14 Adapter Gasket
12 Spiral‐Wound Gasket N06600/Graphite
53 Shim S31600
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
58
Keys 10*, 11*, 12*, 13*, 14*, and 53* Gaskets and Shims
Valve Size, NPS Key Number
Standard Trim CageWhisper Trim I Cage
Cavitrol III - 1 Stage Cage
Cavitrol III - 2 Stage CageWhisper Trim III Cage
WhisperFlo Cage
-198 to 593�C (-325 to 1100�F) -198 to 593�C (-325 to 1100�F)
Part Number Part Number
4x2
Set10121353
RGASKETX1821R3299X00421R3297994421R3296X004216A1938X012
RGASKETX4421R3299X0042 (qty 2)
1R3297994421R3296X004216A1938X012
6x4x2‐1/2
Set101112131453
RGASKETX2821R3724X00421R3846X00421R3845994421R3844X00521J5047X006216A1939X012
- - -- - -- - -- - -- - -- - -- - -
6x4 or 8x4
Set10121353
RGASKETX2121R3724X00421R3722994421J5047X006216A1941X012
RGASKETX4721R3724X0042 (qty 2)
1R3722994421J5047X006216A1941X012
8x6 or 12x6CL300, CL600, or CL900
Set10121353
RGASKETX3921U5081X00521U5085994421V64419944216A1942X012
- - -- - -- - -- - -- - -
8x6 or 12x6Whisper I
Set10 (qty 2)
121353
RGASKETX4121U5081X00521U5085994421V64419944216A1942X012
- - -- - -- - -- - -- - -
10x8 or 12x8Set1013
RGASKETX23210A3265X11210A3266X082
10A3265X15210A3265X112 (qty 2)
10A3266X082
*Recommended spare parts
Instruction ManualD100399X012
EW ValveJuly 2017
59
Instruction ManualD100399X012
EW ValveJuly 2017
60
Emerson Automation Solutions Marshalltown, Iowa 50158 USASorocaba, 18087 BrazilCernay 68700 FranceDubai, United Arab EmiratesSingapore 128461 Singapore
www.Fisher.com
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are notto be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales aregoverned by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of suchproducts at any time without notice.
� 1973, 2017 Fisher Controls International LLC. All rights reserved.
Fisher, ENVIRO-SEAL, WhisperFlo, Whisper Trim, Cavitrol, and easy-e are marks owned by one of the companies in the Emerson Automation Solutionsbusiness unit of Emerson Electric Co. Emerson Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson ElectricCo. All other marks are the property of their respective owners.
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenanceof any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.