Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
E-1
INSTALLATION MANUAL
A4M1-9950-00
IC-209/NC-504 Image Controller/Network Card
1BS0833001
I. Accessory parts[IC-209/NC-504: Image Controller/Network Card]
* NC-504 includes the network card board.
[MK-733: Extended Operation Panel]
Note:When you install the image controller (IC-209) or network card (NC-504), using the extended opera-tion panel (MK-733) is recommended.
Note:This manual provides the illustrations of the acces-sory parts and machine that may be slightly differ-ent in shape from yours. In that case, instead of the illustrations, use the appearance of your machine to follow the installation procedure. This does not cause any significant change or problem with the procedure.
No. Name Shape Q’ty
1. Image controller board * 1
2. Cable
1
3. Plate A
1
4. Plate B
1
5. Plate C
1
6. Screw (3 x 8 mm) 7
7. CD-ROM1
8. Installationmanual 1
set
A4M1IXC001DA
A4M1IXC002DA
A4M1IXC004DA
A4M1IXC003DA
A4M1IXC005DA
A0DCIXC016DA
4040IXC111DA
4980IXC019DA
No. Name Shape Q’ty
1. Extended operation panel 1
2. Cable
1
3. Panel sheet
1set
After unpacking, be sure to get rid of the packaging materials and keep them out of the reach of children.Putting the head in the plastic bag involves danger of suffocation.
A4M1IXC006DA
A4M1IXC007DA
A4M1IXC019DA
Applied Machines: 235/215/195MFP: 23 ppm/21 ppm/19 ppmProduct Code: A3PE/A3R2
E-2
II. Installation proceduresNote:
When you install the optional fax kit (FK-510), install it before installing the IC-209/NC-504 to the machine.
1. Turn off the machine and unplug the power cord from the power outlet.
2. Remove the rear cover. (11 screws)
3. Remove the knockout of the left cover with nip-pers.
Note:When removing the knockout, hold it with your hand to prevent it from being thrown.
4. Attach the supplied plate A to the machine at the position shown in the illustration. (One supplied screw)
Note:When the FK-510 is installed in the machine, this step is unnecessary.
5. Attach the supplied plate B to the machine at the position shown in the illustration. (One supplied screw)
Note:When the FK-510 is installed in the machine, this step is unnecessary.
6. Attach the supplied plate C to the machine at the position shown in the illustration. (One supplied screw)
A4M5IXC020DA
A4M1IXC025DA
Knockout
A4M2IXC006DA
A4M2IXC007DA
A4M1IXC011DA
E-3
7. Connect the supplied cable to the machine.Note:
If the fax board is mounted, temporarily remove it. (Three screws and one board holder)
8. Connect the image controller board/network card board to the cable described in step 7.
9. Mount the image controller board/network card board to the machine at the position shown in the illustration. (Four supplied screws)
10. Reinstall the rear cover. (11 screws)Note: • When the optional reverse automatic document
feeder (DF-625) is installed, make sure that the harness cover is not detached, and then attach the rear cover.
• Be aware that only the screw A is different from other screws.
A4M2IXC020DA
A4M1IXC012DA
Board holder
A4M1IXC013DA
A4M1IXC014DA
A3PFIXC021DA
Harness cover
A
E-4
III. Installing the extended operation panel (MK-733)1. Release the two claws using a flat-blade screw-
driver and remove the cover.
2. Connect the cable supplied with the extended operation panel to the machine as shown in the illustration.
3. Connect the other end of the cable described in step 2 to the extended operation panel.
4. Attach the extended operation panel to the machine.
Note:Put the claws of the extended operation panel in the indicated holes and push the panel from above to fit its claws into the holes.
5. Affix the panel sheet supplied with the extended operation panel.
(1) Remove the switching plate.
(2) Affix the panel sheet to the extended operation panel.
Note:Place the proper panel sheet which corresponds to the applicable marketing area.
(3) Reinstall the switching plate that has been removed in step (1).
A4M1IXC015DA
Cover
Claw
A4M1IXC016DA
A4M1IXC017DA
A4M1IXC018DA
Claw
Hole
A4M1IXC023DA
A4M1IXC024DA