Embed Size (px)
Citation preview
DSC193
ICF Finish System 100% Textured Acrylic Finishing Systems (TAFS) For Use Over Insulating Concrete Forms (ICF)
ICF Finish System Installation Details
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
and Dryvit specifically disclaims any liability for the use of this
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
TABLE OF CONTENTS
ICF Finish System
2004 DryvitC
APPROVED BY:
RS 0
REV: DATE:
2/04
version.
®
NOTE
DETAILICFFS Finish System Cutaway
Base Detail- Height Adjuster
Head/Sill- Bucksaver Rough Buck
ICFFS 0.0.06
ICFFS 0.0.05
ICFFS 0.0.04
ICFFS 0.0.03
ICFFS 0.0.02
ICFFS 0.0.01
Base Detail- Tapered Cut Form
ICFFS 0.0.07
Base Detail- Cut Form
Base Detail- EPS Trim
Base Detail- Without Inspection Strip
DRYVIT MAKES NO REPRESENTATION REGARDING
CONFORMITY OF ITS SUGGESTIONS TO MODEL BUILDING
CODES, ENGINEERING CRITERIA, SPECIFIC APPLICATIONS OR
PROJECT LOCATIONS. ALL COMPONENTS INDICATED IN
ILLUSTRATIONS, AS WELL AS OTHERS THAT MAY BE
REQUIRED FOR THE INTEGRITY OF THE SYSTEM SHALL BE
DESIGNED, DETAILED AND ENGINEERED BY
REPRESENTATIVES OF THE ARCHITECT, OWNER OR
CONTRACTOR TO BE IN CONFORMANCE WITH MODEL CODES,
ARCHITECTURAL AND ENGINEERING REQUIREMENTS
PERTAINING TO SPECIFIC BUILDING PROJECTS.
DRYVIT MAKES NO WARRANTY, EXPRESSED OR
IMPLIED, AS TO THE ARCHITECTURAL DESIGN,
ENGINEERING, OR WORKMANSHIP OF PROJECTS
UTILIZING DRYVIT SYSTEMS OR PRODUCTS.
THE LIABILITIES OF DRYVIT SHALL BE AS
STATED IN THE DRYVIT STANDARD
WARRANTY. CONTACT DRYVIT FOR A FULL
AND COMPLETE COPY OF THIS WARRANTY.
with EPS Trim
Head/Sill- Wood Rough Buck
with EPS TrimICFFS 0.0.08
Head/Sill- Bucksaver Rough Buck ICFFS 0.0.09
Head/Sill- Wood Rough Buck ICFFS 0.0.10
ICFFS 0.0.11Head/Sill- Flange Mount
ICFFS 0.0.12Head/Sill- Recessed
ICFFS 0.0.13A/C Penetration
ICFFS 0.0.14Eave Detail- Recessed Top Plate
ICFFS 0.0.15Eave Detail- Exposed Top Plate
ICFFS 0.0.16Eave Detail- Steel Roof Rafters
ICFFS 0.0.17Sloped Roof/Wall Intersection
ICFFS 0.0.18Attachment to Existing Wall
ICFFS 0.0.19Attachment to Steel Column
ICFFS 0.0.20Parapet Termination
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
and Dryvit specifically disclaims any liability for the use of this
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Dryvit ICF Finish System Cutaway
ICFFS 0.0.01
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
ICF Finish SystemNOTE:1.
2004 DryvitC
APPROVED BY:
RS 0
REV: DATE:
2/04
version.
®
BY OTHERS
DRYVIT ICFFS
BY OTHERS
DRYVIT ICFFS OVER
ADDITIONAL LAYER OF EPS
Dryvit TAFS
Over ICF
ICF
DRYVIT BASE COAT
DRYVIT REINFORCING MESH
DRYVIT BASE COAT
DRYVIT FINISH
ICF
DRYVIT ADHESIVE
EXPANDED POLYSTYRENE
INSULATION BOARD (MIN. 1")
DRYVIT BASE COAT
DRYVIT REINFORCING MESH
DRYVIT BASE COAT
DRYVIT FINISH
Dryvit TAFS
Over Additional
Layer of EPS
Over ICF
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT DRYFLEX
BASE COAT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
WATERPROOFING MEMBRANE
& DRAINAGE / PROTECTION
BOARD AS SPEC'D
DRYFLEX TO BE LAPPED OVER
WATERPROOFING AT GRADE
LEVEL MIN 6"
DRYVIT FINISH
BURIED WEB FORM UNIT
SEE DETAIL BELOW
ELEV. OF TERMITE INSPECTION
STRIP ABOVE FIN. GRADE
6" TO 8" AS PER CODE
TEMPORARY PLYWOOD
FORM FASTENED TO WEBS
PRIOR TO CONCRETE PLACEMENT
TO CREATE INSPECTION STRIP
HEIGHT ADJUSTER (3-3/8")
2.
1.NOTE:
2004 Dryvit
ICF Finish System
C
MINOR CRACKING IS POSSIBLE
IN THE FINISHED EXTERIOR
SURFACE AT ICF/CONCRETE
TRANSITIONS
DETAIL RECOMMENDED WHEN
AN INSPECTION STRIP IS
REQUIRED BY LOCAL
JURISDICTION OR BY PEST
CONTROL OPERATORS
3.
RS
APPROVED BY:
FORM SPACE TO BE EQUAL
TO HEIGHT ADJUSTER AT
OPPOSITE SIDE OF FORM
APPLY REINFORCED DRYVIT
DRYFLEX® BASE COAT OVER
INSPECTION STRIP EXTENDING
MIN. 6" OVER ICF ABOVE AND
BELOW, AND MIN. 12" FROM
GRADE
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Base Detail - Height Adjuster
REV:
0
DATE:
2/04
version.
®
ICFFS 0.0.02
2/04
DATE:
DRYVIT FINISH
BURIED WEB FORM UNIT
Base Detail - Cut Form
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
version.
®
ICFFS 0.0.03
SEE DETAIL BELOW
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL
FACADES EXPOSED TO ABNORMAL
STRESS, HIGH TRAFFIC, OR DELIBERATE
IMPACT HAVE THE BASE COAT
REINFORCED WITH PANZER ® MESH
PRIOR TO STANDARD ™ OR STANDARD
PLUS™ MESH. LOCATION OF HIGH
IMPACT ZONES SHOULD BE INDICATED
ON CONTRACT DOCUMENTS
CUT SECTION OF FORM
4" MIN. OR AS REQUIRED
BY CODE
APPLY REINFORCED DRYVIT
DRYFLEX® BASE COAT OVER
INSPECTION STRIP EXTENDING
MIN. 6" OVER ICF ABOVE AND
BELOW, AND MIN. 12" FROM GRADE
ELEV. OF TERMITE INSPECTION
STRIP ABOVE FIN. GRADE
6" TO 8" AS PER CODE
WATERPROOFING MEMBRANE
& DRAINAGE / PROTECTION
BOARD AS SPEC'D
DRYFLEX TO BE LAPPED OVER
WATERPROOFING AT GRADE
LEVEL MIN 6"
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE
COAT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT DRYFLEX
BASE COAT
TEMPORARY PLYWOOD
FORM FASTENED TO WEBS
PRIOR TO CONCRETE PLACEMENT
TO CREATE INSPECTION STRIP
MINOR CRACKING IS POSSIBLE
IN THE FINISHED EXTERIOR
SURFACE AT ICF/CONCRETE
TRANSITIONS
DETAIL RECOMMENDED WHEN
AN INSPECTION STRIP IS
REQUIRED BY LOCAL
JURISDICTION OR BY PEST
CONTROL OPERATORS
ICF Finish System
1.NOTE:
C 2004 Dryvit
2.
3.
APPROVED BY:
RS 0
REV:
4" MIN. OR AS REQUIRED BY CODE
CUT SECTION OF FORM
WITH 45° TAPER
APPLY REINFORCED DRYVIT
DRYFLEX® BASE COAT OVER
INSPECTION STRIP EXTENDING MIN. 6"
OVER ICF ABOVE AND BELOW,
AND MIN. 12" FROM GRADE
BURIED WEB FORM UNIT
ELEV. OF TERMITE INSPECTION
STRIP ABOVE FIN. GRADE
6" TO 8" AS PER CODE
WATERPROOFING MEMBRANE
& DRAINAGE / PROTECTION
BOARD AS SPEC'D
DRYFLEX TO BE LAPPED
OVER WATERPROOFING AT
GRADE LEVEL MIN 6"
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
MINOR CRACKING IS POSSIBLE
IN THE FINISHED EXTERIOR
SURFACE AT ICF/CONCRETE
TRANSITIONS
DETAIL RECOMMENDED WHEN
AN INSPECTION STRIP IS
REQUIRED BY LOCAL
JURISDICTION OR BY PEST
CONTROL OPERATORS
ICF Finish System
1.NOTE:
2004 DryvitC
2.
Base Detail - Tapered Cut Form
Dryvit products is the responsibility of the project's design
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
and Dryvit specifically disclaims any liability for the use of this
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
®
ICFFS 0.0.04
DRYVIT COMPATIBLE SEALANT
EPS FILLER MIN 1" ATTACHED
TO ICF WITH DRYVIT ADHESIVE
2/04
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
DATE:
RS
APPROVED BY:
3.
0
REV:
version.
DRYVIT FINISH
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
and Dryvit specifically disclaims any liability for the use of this
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Dryvit products is the responsibility of the project's design
Base Detail - EPS Trim
ICFFS 0.0.05
BURIED WEB FORM UNIT
APPLY REINFORCED DRYVIT
DRYFLEX BASE COAT MIN.
12" FROM GRADE
WATERPROOFING MEMBRANE
& DRAINAGE / PROTECTION
BOARD AS SPEC'D
DRYFLEX TO BE LAPPED
OVER WATERPROOFING AT
GRADE LEVEL MIN 6"
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT DRYFLEX®
BASE COAT
ICF Finish System
SEE DETAIL 1, 2, & 3 WHEN
PROTECTION FROM WOOD
BORING INSECTS IS DETERMINED
TO BE NECESSARY
2004 DryvitC
NOTE:1. DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
APPROVED BY:
RS 0
REV:
2.
DATE:
2/04
version.
EPS SHAPE
DRYVIT FINISH
DRYVIT ADHESIVE
®
DRYVIT FINISH
BURIED WEB FORM UNIT
WATERPROOFING MEMBRANE
& DRAINAGE / PROTECTION
BOARD AS SPEC'D
DRYFLEX TO BE LAPPED
OVER WATERPROOFING AT
GRADE LEVEL MIN 6"
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT DRYFLEX®
BASE COAT (MIN. 6" ON EACH SIDE
OF ICF JIONT)
APPLY REINFORCED DRYVIT
DRYFLEX BASE COAT MIN. 12"
FROM GRADE
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
1.NOTE:
ICF Finish System
2004 DryvitC
SEE DETAIL 1, 2, & 3 WHEN
PROTECTION FROM WOOD
BORING INSECTS IS DETERMINED
TO BE NECESSARY
APPROVED BY:
RS
2.Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Base Detail - Without Inspection Strip
DATE:REV:
0 2/04
version.
®
ICFFS 0.0.06
VINYL BUCK SYSTEM
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
Head/Sill - Bucksaver Rough Buck With EPS Trim
THIS DETAIL IS RECOMMENDED
FOR USE IN COMBUSTIBLE
CONSTRUCTION ONLY.
ICF Finish System
C 2004 Dryvit
NOTE:1.
APPROVED BY: REV:
RS 0
2.
DATE:
2/04
DRYVIT FINISH
DRYVIT ADHESIVE
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
BURIED WEB FORM UNIT
FLANGE MOUNT WINDOW
MIN 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES
DRYVIT COLOR PRIME™ OR
DEMANDIT® ON SURFACES TO
RECEIVE SEALANT
DRYVIT FLASHING TAPE ™ EXTENDED
OVER ENTIRE SILL AND ONTO FRONT
FACE OF VERTICAL WALL
ATTACH EPS SHAPE WITH
VERTICAL NOTCHED TROWEL
ADHESIVE PATTERN
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES
MIN 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
DRYVIT BACKSTOP NT™ AND GRID
TAPE EXTENDED TO THE INSIDE
FACE OF THE WALL
EPS SHAPE
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
version.
®
ICFFS 0.0.07
1/2" GYPSUM BRD.
FLANGE MOUNT WINDOW
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
MIN 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
DRYVIT COLOR PRIME™ OR
DEMANDIT® ON SURFACES TO
RECEIVE SEALANT
ATTACH EPS SHAPE WITH
VERTICAL NOTCHED TROWEL
ADHESIVE PATTERN
DRYVIT FLASHING TAPE ™ EXTENDED
OVER ENTIRE SILL AND ONTO FRONT
FACE OF VERTICAL WALL
MIN 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
DRYVIT BACKSTOP NT™ AND GRID
TAPE EXTENDED TO THE INSIDE
FACE OF THE WALL
ICF Finish System
THIS DETAIL IS RECOMMENDED
FOR USE IN COMBUSTIBLE
CONSTRUCTION ONLY.
2004 DryvitC
NOTE:1.
2"x12" ROUGH BUCK
W/ SILL GASKET
PRESSURE TREATED IF SPEC'D
2"X4" INSIDE & OUTSIDE FACE
TO PERMIT CONCRETE
PLACEMENT
®
and Dryvit specifically disclaims any liability for the use of this
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Dryvit products is the responsibility of the project's design
Head/Sill - Wood Rough Buck With EPS Trim
ICFFS 0.0.08
2/04
DATE:
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
RS
APPROVED BY:
2.
REV:
0
version.
DRYVIT ADHESIVE
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES
DRYVIT FINISH
EPS SHAPE
BURIED WEB FORM UNIT
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES 1/2" GYPSUM BRD.
DATE:
2/04
version.
®
1/2" GYPSUM BRD.
VINYL BUCK SYSTEM
ICFFS 0.0.09
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
TRIM VINYL BUCKSAVER BACK
FROM OUTSIDE FACE OF THE FORM
TO ALLOW FOAM TO DRYVIT COATING
CONTACT
BURIED WEB FORM UNIT
DRIP
EPS ATTACHED WITH
DRYVIT AP ADHESIVE ™
DRYVIT FINISH
COLOR PRIME™ OR DEMANDIT® ON
SURFACES TO RECEIVE SEALANT
MIN. 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
and Dryvit specifically disclaims any liability for the use of this
Head/Sill - Bucksaver Rough Buck
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
CONTINUOUS TO INSIDE FACE
OF THE OPENING
THIS DETAIL IS RECOMMENDED
FOR USE IN COMBUSTIBLE
CONSTRUCTION ONLY.
ICF Finish System
2004 DryvitC
1.NOTE:
SEALANT
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
APPROVED BY:
RS 0
REV:
METAL FLASHING EXTENDED
TO INSIDE FACE OF WALL
2.
version.
®
BURIED WEB FORM UNIT
DRYVIT FINISH
DRIP
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
EPS ATTACHED WITH
DRYVIT AP ADHESIVE ™
COLOR PRIME™ OR DEMANDIT® ON
SURFACES TO RECEIVE SEALANT
MIN. 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
1/2" GYPSUM BRD.
RECESSED 2"x6" BUCK
ICFFS 0.0.10
SEALANT
METAL FLASHING EXTENDED
TO INSIDE FACE OF FRAMING
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
CONTINUOUS TO INSIDE FACE
OF THE OPENING
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
1.NOTE:
2004 Dryvit
ICF Finish System
C RS
APPROVED BY:
THIS DETAIL IS RECOMMENDED
FOR USE IN COMBUSTIBLE
CONSTRUCTION ONLY.
2.
2"X3" INSIDE & OUTSIDE FACE
TO PERMIT CONCRETE
PLACEMENT
and Dryvit specifically disclaims any liability for the use of this
Dryvit products is the responsibility of the project's design
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Head/Sill - Wood Rough Buck
REV:
0
DATE:
2/04
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Head/Sill - Flange Mount
®
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
version.
DRYVIT ADHESIVE
BURIED WEB FORM UNIT
MIN. 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
FLANGE MOUNT WINDOW
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES
DRYVIT COLOR PRIME™ OR
DEMANDIT® ON SURFACES TO
RECEIVE SEALANT
DRYVIT BACKSTOP NT™ AND GRID
TAPE EXTENDED TO THE INSIDE
FACE OF THE WALL
DRYVIT FINISH
EPS SHAPE
ICFFS 0.0.11
1/2" GYPSUM BRD.
MIN. 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
ATTACH EPS SHAPE WITH
VERTICAL NOTCHED TROWEL
ADHESIVE PATTERN
DRYVIT FLASHING TAPE ™ EXTENDED
OVER ENTIRE SILL AND ONTO FRONT
FACE OF VERTICAL WALL
MIN 6:12 SLOPE ON ALL
PROJECTING SURFACES
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
ICF Finish System
C 2004 Dryvit
NOTE:1.
APPROVED BY:
RS
REV:
0
DATE:
2/04
METAL FLASHING EXTENDED
TO INSIDE FACE OF WALL
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
CONTINUOUS TO INSIDE FACE
OF THE OPENING
ICF Finish System
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
2004 DryvitC
1.NOTE:
®
and Dryvit specifically disclaims any liability for the use of this
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Dryvit products is the responsibility of the project's design
Head/Sill - Recessed
SEALANT
2/04
DATE:APPROVED BY:
RS
REV:
0
version.
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
COLOR PRIME™ OR DEMANDIT® ON
SURFACES TO RECEIVE SEALANT
MIN. 1/2" DRYVIT COMPATIBLE
SEALANT AND CLOSED CELL
BACKER ROD (TYP.)
1/2" GYPSUM BRD.
ICFFS 0.0.12
BURIED WEB FORM UNIT
DRYVIT FINISH
EPS ATTACHED WITH
DRYVIT AP ADHESIVE ™
DRIP
2"x4" BLOCKING FOR STEEL
INSERT FASTENING POINT
AS SPEC'D BY A.C.
INSTALLATION
PTAC SLEEVE INSERT
AS SPEC'D
ICFFS 0.0.13
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
and Dryvit specifically disclaims any liability for the use of this
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
WRAPPED TO THE INSIDE FACE
OF THE FRAMING
DRYVIT COMPATIBLE SEALANT
AND CLOSED CELL BACKER ROD (TYP.)
DRYVIT COMPATIBLE SEALANT AND
CLOSED CELL BACKER ROD (TYP.) WITH
DRYVIT DEMANDIT® OR COLOR PRIME™
ON SURFACES TO RECEIVE SEALANT
MIN. 1/2" DIMENSION BETWEEN
ICF AND PTAC SLEEVE
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
ICF Finish System
2004 DryvitC
NOTE:1.
APPROVED BY:
RS 0
REV:
METAL FLASHING EXTENDED
TO INSIDE FACE OF WALL
SEALANT
2/04
DATE:
version.
BURIED WEB FORM UNIT
®
A/C Penetration
ALUM. SOFFIT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
WRAPPED OVER TOP PLATE
DRYVIT FINISH
BURIED WEB FORM UNIT
2"x6" RECESSED PLATE
ON SILL GASKET ANCHORED
TO CONCRETE PER LOCAL
CODE REQMT.
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
1.NOTE:
ICF Finish System
2004 DryvitC RS
APPROVED BY:
1/2" GYPSUM BRD.
and Dryvit specifically disclaims any liability for the use of this
Dryvit products is the responsibility of the project's design
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Eave Detail - Recessed Top Plate
0
REV:
2/04
DATE:
version.
®
ICFFS 0.0.14
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Eave Detail - Exposed Top Plate
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
version.
®
1/2" GYPSUM BRD.
ICFFS 0.0.15
ALUM. SOFFIT
BURIED WEB FORM UNIT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
DRYVIT FINISH
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
WRAPPED OVER TOP PLATE
2"x12" EXPOSED PLATE
ON SILL GASKET ANCHORED
TO CONCRETE PER LOCAL
CODE REQMT.
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
ICF Finish System
C 2004 Dryvit
NOTE:1.
APPROVED BY:
RS 0
REV:
2/04
DATE:
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
WRAPPED OVER TOP OF
CONCRETE BEARING
BURIED WEB FORM UNIT
STEEL ROOF FRAMING
CONCRETE POURED
FLUSH WITH TOP OF FORM
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
ICF Finish System
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
2004 DryvitC
NOTE:1.
1/2" GYPSUM BRD.
ICFFS 0.0.16
and Dryvit specifically disclaims any liability for the use of this
Dryvit products is the responsibility of the project's design
®
without notice. Contact Dryvit to insure you have the most recent
The architecture, engineering and design of the project using the
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
professional. All systems must comply with local building codes and
Eave Detail - Steel Roof Rafters
DATE:
2/04
APPROVED BY:
RS
REV:
0
ALUM. SOFFIT
DRYVIT FINISH
version.
DRYVIT COMPATIBLE SEALANT
AND CLOSED CELL BACKER ROD
DRYVIT DEMANDIT® OR COLOR PRIME™
ON SURFACES TO RECEIVE SEALANT
BURIED WEB FORM UNIT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
FLASHING FASTENED TO CONCRETE
INSTALLED IN A WEATHERBOARD
FASHION AS PER NATIONAL
ROOFING CONTRACTORS
ASSOCIATION (NRCA)
ICFFS 0.0.17
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
Sloped Roof/Wall Intersection
MIN. 3/4"
MIN. 2 1/2 "
MIN. 4"
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
ICF Finish System
1.
2004 Dryvit
NOTE:2. SHINGLES SHOULD BE
INSTALLED PER NRCA
GUIDELINES TO OVERLAP STEP
FLASHINGS AND EXTEND ALL
THE WAY TO THE VERTICAL
WALL
APPROVED BY:
RS 0
REV: DATE:
2/04
version.
ROOFING PAPER
ROOF RAFTER
DRYVIT FINISH
®
C
THE JOINT BETWEEN THE TWO
WALLS MAY OR MAY NOT BE A
STRUCTURAL CONNECTION WITH
DOWELS AS SPEC'D BY THE
STRUCTURAL ENGINEER
IT IS THE RESPONSIBILITY OF THE
DESIGNER AND CONTRACTOR TO
DESIGN AND CONSTRUCT THE
WALLS SO THE EXTERIOR FINISH OF
BOTH THE ICF WALL AND THE CMU
WALL ARE IN THE SAME PLANE
DRYVIT FINISH
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
DRYVIT EIFS
BACK WRAP EPS SECTION
WITH MESH AND BASE COAT
DRYVIT DEMANDIT® OR
COLOR PRIME™ ON SURFACES TO
RECEIVE SEALANT WITH BACKER ROD
SEE DETAIL BELOW
DRYVIT RECOMMENDS THAT
GROUND FLOOR APPLICATIONS AND
ALL FACADES EXPOSED TO
ABNORMAL STRESS, HIGH TRAFFIC,
OR DELIBERATE IMPACT HAVE THE
BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™
OR STANDARD PLUS ™ MESH.
LOCATION OF HIGH IMPACT ZONES
SHOULD BE INDICATED ON
CONTRACT DOCUMENTS
1.
2004 DryvitC RS
APPROVED BY:
3.
ICF Finish SystemNOTE: 2.
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
and Dryvit specifically disclaims any liability for the use of this
REV:
0 2/04
DATE:
version.
®
DRYVIT DEMANDIT OR COLOR PRIME
ON SURFACES TO RECEIVE SEALANT
EXSTG. CONCRETE
BLOCK WALL
DRYVIT COMPATIBLE SEALANT
AND CLOSED CELL BACKER ROD
ICFFS 0.0.18
The architecture, engineering and design of the project using the
Dryvit products is the responsibility of the project's design
Transition to Existing Wall
3/4"
STEEL COLUMN ANCHORED
IN PLACE
WOOD BLOCKING
NELSON STUDS CAST
INTO CONCRETE
1. DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH
PANZER ® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
C 2004 Dryvit
APPROVED BY:
RS
REV:
0 2/04
DATE:
EPS INSERT
BURIED WEB FORM UNIT
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
DRYVIT FINISH
DRYVIT AP ADHESIVE ™
ICF Finish SystemNOTE:
professional. All systems must comply with local building codes and
without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail
does not violate Dryvit's warranty. This detail is subject to change
any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
discretion, whether this detail or a functionally equivalent alternative
detail and for the architecture, design, engineering or workmanship of
and Dryvit specifically disclaims any liability for the use of this
version.
®
The architecture, engineering and design of the project using the
Transition Across Column
ICFFS 0.0.19
1/2" GYPSUM BRD.
Dryvit products is the responsibility of the project's design
PLAN VIEW
DRYVIT REINFORCING MESH
EMBEDDED IN DRYVIT BASE COAT
BURIED WEB FORM UNIT
DRYVIT RECOMMENDS THAT GROUND
FLOOR APPLICATIONS AND ALL FACADES
EXPOSED TO ABNORMAL STRESS, HIGH
TRAFFIC, OR DELIBERATE IMPACT HAVE
THE BASE COAT REINFORCED WITH PANZER
® MESH PRIOR TO STANDARD ™ OR
STANDARD PLUS ™ MESH. LOCATION OF
HIGH IMPACT ZONES SHOULD BE
INDICATED ON CONTRACT DOCUMENTS
ICF Finish System
1.
2004 DryvitC
NOTE:
DRYVIT BASE COAT WRAPPED
ONTO CONCRETE
ROOFING AS SPEC'D
ROOFING MEMBRANE LAPPED
OVER PARAPET BLOCK
®
professional. All systems must comply with local building codes and
detail and for the architecture, design, engineering or workmanship of
discretion, whether this detail or a functionally equivalent alternative
standards. This detail is for general information and guidance only
any project. The project design professional determines, in its sole
does not violate Dryvit's warranty. This detail is subject to change
is best suited for the project. Use of a functionally equivalent detail
The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this
Parapet Termination
ICFFS 0.0.20
DATE:
2/04
APPROVED BY:
RS 0
REV:
version.
WOOD SPACER
DRYVIT FINISH
PARAPET CAP
SEALANT
MIN. 2 1/2" OVERLAPRETAINING CLIP
![ICF-M770L/M770S/M770SL - Kazenice.kaze.com/sony_icf-m770sl_svm.pdf · ICF-M770L/M770S/M770SL no mark: common (): ICF-M770L []: ICF-M770S 〈〈 〉〉: ICF-M770SL AM IF ADJUSTMENT](https://img.pdfslide.net/doc/110x75/5f05960a7e708231d413b21e/icf-m770lm770sm770sl-icf-m770lm770sm770sl-no-mark-common-icf-m770l-.jpg)
