iControl Demo Setup

April 2017

2

iControl Demo Setup

Please, follow the steps below:

1. Unzip the iControl.DEMO.v5.zip file (password: “igrid”)

2. Execute the “iControl.exe” file located in the “bin” folder (iControl.DEMO.V5\iControl\bin)

3. The following message is displayed:

Select “Cancel”.

3

iControl Demo Setup

4. The “User Management” window is displayed. Enter the following user & password:

• User: admin

• Password: admin

5. Then press “Ok”

4

iControl Demo Setup

6. iControl main window will open:

5

iControl Demo Setup

7. Left-click the “Play” button on the top-left side of the iControl screen and select the “Simulate” option:

6

iControl Demo Setup

9. The simulate window is then displayed:

10. Set “Value” field to “1”.

11. Click “Send” button.

7

iControl Demo Setup

12. The demo simulation is started (now you can close the simulate window)

In order to stop the demo simulation, left-click over the “Stop” icon select the “Simulate” optionSet “Value” = 0, and the demo will be stopped.

8

iControl Demo Setup

Click the “Fit to screen” option in the iControl toolbar in order to fit the entire schemas/drawings toyour screen area.

9

iControl Demo Setup

10

iControl Demo: Command windows

• Click the components (circuit breakers and isolators) in the “66kV Overview” screen in order to open the commandwindows.

11

iControl Demo: Command windows & Pop-ups

• Commands will be enabled/disabled depending on the pre-configured logic & interlocking rules.

• In the above command window, the “OPEN” command is enabled (command button with black text color) and the“CLOSE” command is disabled (command button with grey text color).

• By clicking on the “Interlocking” button in the command window, iControl opens a pop-up window with informationabout the configured logic & interlocking rules.

• Command windows can be customized by the user.

• User can configure any schema to be displayed as a pop up window.

12

iControl Demo: Change to other schemas

• In order to change to another schema:

• click the top tabs, or

• click the top-right side buttons:

13

iControl Demo - Listings

• Open the iControl listings (active alarm lists, sequence of events list, alarms acknowledgment list, etc.) from either:

• the iControl Runtime toolbar, or

• the top-right side buttons

14

iControl Demo - Charts

• “Feeder 1 Charts”, “Feeder 2 Charts”, “Feeder 3 Charts”, “Trafo 1 Charts”, “Trafo 2 Charts” and “Bus Coupler Charts”schemas contain some examples of embedded charts:

15

iControl Demo - Charts

• Schemas with embedded charts can also be displayed as pop-up windows.

• For example:

• change to “66 kV Feeder 1”, and click the following image:

• A pop-up window will be displayed with the embedded charts:

16

iControl Demo - Charts

• Real-time charts (floating window charts) can also displayed by left-clicking any of the measurement boxes:

17

iControl Demo - Charts

• Different measures can be added to the same real-time chart:

18

iControl Demo: ALC

• The iControl ALC (Automatic Line Coloring or Topological Coloring) functionality allows easy automatic coloring ofelectrical lines based-on topology of the grid and voltage level. Lines (busbars and connections) and graphicalcomponents (circuit breakers, isolators, transformers, etc.) are colored using pre-configured colors, based-on theenergization status: energized (under power), not energized (not feeded), and grounded.

• In the energized case, the lines and elements may be colored using two modes:

• Energy-based: coloring according to voltage level. Lines may be displayed in different colors depending on voltagelevel.

• Flow-based: coloring according to the power flow. This mode allows viewing power flows (one single color perflow) when lines are energized. For example, this mode allows to display the part of the grid being supplied bythe same incoming feeder with the same color.

19

iControl Demo Setup

• The user can switch between the ALC viewing modes by clicking the “Energization mode” button in the iControltoolbar:

Energy-based (E) mode isselected. Click this button inorder to switch to Flow-based(F) mode.

Flow-based (F) mode isselected. Click this button inorder to switch to Energy-based (E) mode.

20

iControl Demo Setup

• By default the iControl demo uses energy-based ALC viewing mode.

• Colors for all energization status are configurable by the user. Inthis example we have used the following:

• Green: energized (under power) color for 66kV lines.

• Blinking grey: not-energized (not feeded) color.

• White: grounded color.

21

• Energized (under power) colors used for the different flows in this demo:

• Flow 1 in blue (feeder 1)• Flow 2 in light blue (feeder 2)• Flow 3 in orange (feeder 3)

• Blinking grey: not-energized (not feeded) color.

• White: grounded color

iControl Demo Setup

• If switching to flow-based ALC viewing mode.

22

Smart Solutions for Smart Grids

Address :

Barcelona Advanced Industry Park

C. Marie Curie, 8-14

08042 – Barcelona

Web : www.igrid-td.comLet's keep your lights

shinning