IL 012035EN Supersedes February 2014 Installation ......RG-DC Frame Circuit Breaker Eaton Electrical Sector 1000 Eaton Boulevard Cleveland 44122 nited States 77-EN-CRE 77-36-2273 Eatoncom

ContentsDescription Page

RG-DC Frame Circuit Breaker . . . . . . . . . . . . . . . . 2Mounting Bolt Drilling Plan . . . . . . . . . . . . . . . . . . 2Escutcheon Dimensions . . . . . . . . . . . . . . . . . . . . 3Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . 4

Effective February 2017Supersedes February 2014Instruction Leaflet IL 012035EN

Installation Instructions forRG-DC Frame Circuit Breaker

2

Instruction Leaflet IL 012035ENEffective February 2017


EATON www.eaton.com

D WARNINGDO NOT ATTEMPT TO INSTALL OR PERFORM MAINTENANCE ON EQUIP-MENT WHILE IT IS ENERGIZED. DEATH, SEVERE PERSONAL INJURY, OR SUBSTANTIAL PROPERTY DAMAGE CAN RESULT FROM CONTACT WITH ENERGIZED EQUIPMENT. ALWAYS VERIFY THAT NO VOLTAGE IS PRESENT BEFORE PROCEEDING WITH THE TASK AND ALWAYS FOLLOW GENERALLY ACCEPTED SAFETY PROCEDURES. EATON IS NOT LIABLE FOR THE MISAP-PLICATION OR MISINSTALLATION OF ITS PRODUCTS.

Figure 1. RG-DC Frame Circuit Breaker.

Figure 2. Mounting Bolt Drilling Plan.

7.750[196,85]

15.000[381,00]

14.500[368,30]

7.250[184,15] CIRCUIT

BREAKERHANDLE

q

q

CIRCUIT BREAKERHANDLE

TOP

BOTTOM

.438[11.13]Dia(4 Holes). Use.375 [M11] Dia. Boltsfor MountingCircuit Breaker

DRILLING PLAN

OFF

3



EATON www.eaton.com

Figure 3. Escutcheon Dimensions

Figure 4. Operation.

9.688[246,08]

5.094[129,39]

6.563[166.70]

12.906[327,81]

FRONT COVER CUTOUT

.156 [3.96]Radius(If Required)

q



q

TOP

BOTTOM

OnTrip

OffReset

Push to Trip

Figure 5. Connection Diagram.

Load(A)

Load

Suitable for use on grounded systems that have one leg of load (A)

connected to power supply .

Suitable for use on ungrounded systems .

4



EATON www.eaton.com

Figure 6. Connections.

RatingCatalog Number

TorqueHeat Sinks Per Rear Connectorin.-lb N·m

1000 B2500RD(M) 180 20 2

1250 B2500RD(M) 180 20 2

1600 B2500RD(M) 180 20 2

2000 B2500RD(M) 180 20 2

2500 B2500RD(M) 180 20 2

3000 B3000RD(M) 180 20 4

* Catalog numbers of metric rear connectors contain M.** Single rear connector individually packed.

4 × Hex Bolt: 0 .312-18 × 0 .875 or M8-1 .25 x 20 .0 180 in .-lb (20 N·m)

Step 1 . Install one rear connector .

Step 2. Install one set of heat sinks .

Step 3. Repeat steps one and two to adjacent poles .

5



EATON www.eaton.com

Notes:

6



EATON www.eaton.com

Notes:

7



EATON www.eaton.com

Notes:



EatonElectrical Sector1000 Eaton BoulevardCleveland, OH 44122United States877-ETN-CARE (877-386-2273)Eaton.com

© 2017 EatonAll Rights ReservedPrinted in USAPublication No. IL012035EN / TBG01122Part No. IL012035ENH02February 2017

Eaton is a registered trademark.

All other trademarks are property of their respective owners.

The instructions for installation, testing, maintenance, or repair herein are provided for the use of the product in general commercial applications and may not be appropriate for use in nuclear applica-tions . Additional instructions may be available upon specific request to replace, amend, or supplement these instructions to qualify them for use with the product in safety-related applications in a nuclear facility .

The information, recommendations, descriptions, and safety nota-tions in this document are based on Eaton’s experience and judg-ment with respect to Retrofitting of Power Breakers . This instruction-al literature is published solely for information purposes and should not be considered all-inclusive . If further information is required, you should consult an authorized Eaton sales representative .

The sale of the product shown in this literature is subject to the terms and conditions outlined in appropriate Eaton selling policies or other contractual agreement between the parties . This literature is not intended to and does not enlarge or add to any such contract . The sole source governing the rights and remedies of any purchaser of this equipment is the contract between the purchaser and Eaton .

NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OR WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE, ARE MADE REGARDING THE INFORMATION, RECOMMENDATIONS, AND DESCRIPTIONS CONTAINED HEREIN. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or conse-quential damage or loss whatsoever, including but not limited to damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in the use of existing power facilities, or claims against the purchaser or user by its cus-tomers resulting from the use of the information, recommendations and description contained herein .

Documents

IL 012035EN Supersedes February 2014 Installation ......RG-DC Frame Circuit Breaker Eaton Electrical Sector 1000 Eaton Boulevard Cleveland 44122 nited States 77-EN-CRE 77-36-2273 Eatoncom