Set-Up InstructionsiMote

What you need

1. The iMote (Included)

2. This user guide (Included)

3. TV Channel Icons sticker sheet (Included)

4. Your TV / Cable / Satellite / Remote Control that you currently use to change TV channels on your TV (Not Included)

5. A small Phillips head screwdriver (Not Included)

6. 2 new “AAA” Alkaline Batteries (Not Included)

2

Step1

Place TV Channel Icons stickers on your iMote

1. Select the 5 TV Channels you would like your child to be able to access using the iMote.

2. Find the icons that match the 5 TV Channels you have selected for your iMote on the enclosed sticker sheet. (some of the randomly chosen, pre-installed stickers may already match your preference).

3. If you cannot find an icon to match any of the TV Channels you selected, choose one of the other symbols included to represent that particular channel, or create a new symbol of your own to represent that TV Channel.

4. Place the 5 TV Channel icons stickers you have selected on your iMote (see Figure D below).

5. Continue and follow steps in figures A to E below:

Figure A - Remove the battery compartment door.(I) Remove the “safety screw” with a Phillips screwdriver and retain for later use.

(II) Remove battery door.

(III) Remove batteries (if installed).

I II III

3

Figure C- Remove the front white plastic cover:(I) Carefully remove the cover and clear keys.

(II) Place it on a table while the internal part is facing you.

I II

4

Figure B - Release Button’s cover – remove 4 small screws and retain for later use.

Figure D - Choose your child’s 5 favorite TV Channels icons from the icon sticker sheet included in the iMote package and place them inside the transparent keys.

Figure E - Replace the iMote onto the plastic cover & keys.(I) Leave the white plastic part on the table.

(II) Replace the iMote housing (blue part) onto plastic cover & keys.

(III) Screw the 4 small screws back into their place. Do not over tighten the screws.

I II III

5

Insert Batteries

Figure F - Insert two new “AAA” alkaline batteries in the battery compartment.

(I) Follow the polarity directions (+/-) diagram in the battery compartment.

(II) Close the battery compartment door and tighten the screw with a Philips screwdriver. Do not over-tighten the screws.

Safety Instructions

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon- zinc), or rechargeable (nickel- cadmium) batteries.

I II

6

Step2

What should I do? Indication Illustration

3.1 Start: Enter learning mode

Press 3 keys / buttons “H” “D” & “F” together simultaneously for three (3) seconds.

Red light turns on; indicating iMote is in the learning mode.You must start programming within ten (10) seconds.

3.2 Open programming session / Enter programming mode Press selected Key of the iMote to start programming.

Red light starts flashing, indicating your iMote is "ready to receive data".

Program your child’s 5 favorite TV Channels(please read through all the programming instructions before starting)

Red light

Press selected key to start programming.

Red light flashing

H D

F

7

Step3

What should I do? Indication Illustration

3.3 Program iMote key with selected channel

The iMote can "learn" or “program” 1, 2, or 3 digit channels.Place the red LED light of your home remote control adjacent to the iMote red LED light. The iMote will “capture” the desired channel from the TV/Cable/ Satellite Remote Control. Maximum distance between the two remotes should be 1/2” (1cm).

Press the key of the first digit of the selected channel for up to 3 seconds.(For example, if you want to program channel 125, at this stage press the "1" key only on your TV/Cable/ Satellite Remote). When the iMote is ready to receive the second digit, repeat this step and then repeat it again for the third digit if you are programming a 3 digit channel.

The red flashing light will change to a green flashing light, indicating a digit has been received by your iMote, and then turn red again indicating your iMote is ready to receive additional digits for this session, if needed.

For example: If your child's favorite TV channel is 125 on your TV / Cable / Satellite system, follow these steps:

Press "1" on your TV/Cable/ Satellite Remote. A green light will start flashing on your iMote and will turn to a red flashing light.

Then, when a red light is flashing, press "2" on your TV/Cable/ Satellite Remote and a green light will start flashing on your iMote and will turn into a red flashing light

Then, when a red light is flashing, press "5" on your TV/Cable/ Satellite Remote, and a green light will start flashing on your iMote and will turn into a red flashing light.

max1cm(1/2”)

8

What should I do? Indication Illustration

3.4 Save Once the programming session is done, press the programmed key on your iMote again to save your programming.

The red flashing light will change to a green flashing light, indicating “save” has been received by your iMote, and then thered light will appear constantly indicating your iMote is ready to start additional session.

3.5 Next programming

Repeat steps 3.1 – 3.4 again to program the 4 additional favorite TV channels you select for your iMote.

If you started programming this key, then press it again in order to “save” the programmed session.

The red flashing light will change to a green flashing light and then turn to constant red light

9

Program the “On/Off” and Volume “+/-” Buttons

Exit

Step4

Step5

The On/Off and Volume “+/-” keys / buttons on the iMote come in a disabled mode, as a default. This gives you the choice of preventing your child from controlling these keys independently. This default status allows you the option of only being able to control the “on/off” and “volume” keys from your own TV/Cable/Satellite Remote Control.

To program the “On/Off” and Volume “+/-” keys on your iMote, you should press the volume keys and/or the “On/Off” keys on your TV/Cable/Satellite Remote Control.

If you wish to program the On/Off and Volume “+/-” keys on the iMote, you may simply follow Steps 3.2, 3.3 and 3.4 above if you are still in the “learning mode,” or steps 3.1 - 3.4 if you have already exited the “learning mode”.

Please also note that for your convenience we added two child & parent friendly features: the on/off button will be disable for few seconds after being used to prevent frequent on/off usage and the volume +/- also has a short delay to prevent instant volume change which may scare your child.

Once you have programmed all of your selected TV channels, and /or the On/Off and Volume “+/-” keys on the iMote, wait 10 seconds without pressing any additional keys and the iMote will automatically exit the learning mode. Now your child can start watching their 5 favorite and safe TV channels independently with their new iMote.

The red light will turn off.

Figure F - Do not press any key until the red light will turn off.

10

Test your programmingStep6

What should I do? Indication Illustration

Press a channel on your iMote and point it to your TV/Cable/Satellite. Press it once and do not move the iMote until you see your selected channel on TV. Follow this step to check all programmed channels on your iMote.

If you wish to change your initial TV channel choices, or if for some reason the iMote keys are not programmed properly, please follow Steps 3.1 - 3.4 and repeat the programming process..

The channel you chose will appear on your TV/Cable/Satellite and this will give you an indication that your iMote was programmed properly.

You may also download the iMote Set-Up Instructions from our site:www.comfyland.com

11

Blu

m D

esig

nC

9205

GB

R21

www.comfyland.com