Upload
vanminh
View
222
Download
6
Embed Size (px)
Citation preview
IMPLEMENTATION OF LEAN MANUFACTURING IN FISH CANNING COMPANY: A CASE STUDY OF A CANNED SARDINES
PRODUCTION COMPANY IN MOROCCO
İ. Idrissi* IBN Tofail University Faculty of science kenitra Morocco Afflatus Consulting
A. Mesfioui IBN Tofail University Faculty of science kenitra Morocco
İ. Aftais
Padmanava College of Engineering Rourkela, Odisha-769002, India
A B S T R A C T K E Y W O R D S
A R T I C L E I N F O
Lean, Lean manufacturing, canned fish, optimization
Received 21 June 2015 Accepted 22 July 2015 Available online 1 December 2015
Lean is a powerful tool, which can bring significant
benefit to manufacturing industries by creating value
through reduction of waste. Although the lean concept
has become very popular in mass production industries
such as the automotive industry, more recently the
concept has been adopted in different batch
processing industries and service sectors. The
application of lean tools into the food processing
industry has not received the same level of attention
compared to the traditional manufacturing industries.
The paper discusses how the lean concept could be
applied to a fish manufacturing company. The paper
first presents the lean concept tools. The empirical
section discusses how a case company, operating as
a contract manufacturer in the food industry, has
applied the lean production concept and tools. In the
case study, three analysis tools are examined and the
structures of demand chains of different customers are
presented. The delivery times will decrease and more
flexibility will be needed from the contract
manufacturer. The case study shows that much
movement is possible toward the lean supply chain and
partnership-based cooperation. By implementing the
lean concept, food companies can increase customer
value through cost reduction or through provision of
additional value-enhanced services.
________________________________ * Corresponding Author
2
1. Introduction
This paper focuses on improved understanding of the development of supply-
chain management in a food chain with a special reference to the lean production
concept. Womack and Jones (1996) defined a vision of the future organizational model
of manufacturing, the lean enterprise, as a group of individuals, functions, and legally
separate but operationally synchronized companies. This vision of the modern
production paradigm was described by Henry Ford in the early 1900s, and his writings
were later the basis for the Japanese production philosophy. The new manufacturing
paradigm, the lean management concept that places emphasis on outsourcing,
cooperation, networking, and agility (e.g. Womack, Jones, and Roos 1990), was
developed in the automobile industry and has been widely adopted in engineering-
oriented and assembly industries. So far, little has been written about the applicability of
the concept to the food industry.
This paper presents the lean production concept tools that are used to analyze
and develop production. The empirical illustration shows how a case company,
operating as a contract manufacturer of leading private-label products in the food
industry, has applied the lean production concept and tools.
A change occurred in the relationship between manufacturers and distributor
organizations in the 1980s and 1990s. Within a number of product markets, both food
and non-food, distributors launched their own products that inevitably forced
manufacturing companies to compete with the owner of the shelf space, in addition to
traditional competition with other manufacturers (Håkansson 2000). Store chains and
their brands have increased their market share in Europe and the USA. In Finland, the
share for store brands is about 20 percent. In other European countries the shares
exceed the share of store brands in Finland—e.g., 41 percent in England and 35
percent in Germany. The manufacturing of store brands—i.e., private-label products—is
more commonly assigned to small and medium-sized manufacturers that specialize in
particular product lines and concentrate on producing store brands (Private Label
Manufacturers Association 2005). These companies are called contract manufacturers
or subcontractors. The reasons for outsourcing include lack of inhouse capacity, need
for expertise in technology, financing (e.g., cost-cutting), union avoidance, product life-
cycle (outsourcing of old designs), and organizational changes in operations (Webster
and Beach 1999). According to Dolan and Meredith (2001), there are three reasons why
so many manufacturers have outsourced their products:
1) Money is in the brands, not in the machinery—i.e., the intangible assets are
more valuable than tangibles;
2) Globalization, which implies that production is easy to transfer to countries with
low labor costs; and
3) Only the biggest companies can fully utilize the capacity of their own factories.
In other words, contract manufacturers are able to obtain economies of scale in their
factories.
3
The role of the customer company and contract manufacturers varies within the food
supply chain. The main responsibilities of a contract manufacturer are product planning,
sourcing and allocating materials, preparing and maintaining manufacturing operations,
and product manufacturing. The customer company should provide the product label,
manage the supply chain, and arrange marketing and after-the-sale service.
2. Lean Production
The Lean Production concept, introduced by Womack, Jones, and Roos (1990)
based on a comparative study in the automobile industry from Japanese and other parts
of the world, could be seen as a quantification of earlier “world class” and just-in-time
(JIT) manufacturing studies (Schonberger 1982; Monden 1983; Shingo 1981, 1985).
Womack, Jones, and Roos (1990) described the supply co-ordination system from the
Japanese point of view. Lamming (1993) developed the concept of the Lean Supply
Model, describing supply-chain management practices within lean production. The
origins of lean thinking can be found on the shop-floors of Japanese manufacturers. In
particular, the early work of Toyota has been highlighted. Lean production was first
defined by Womack, Jones, and Roos (1990) as a system that create outputs using less
of every input, similar to the traditional mass-production system but offering an
increased choice for the end user. This definition of lean production was based on the
concept of waste (“muda”) introduced by the Toyota Production System (Shingo 1981).
Waste means non-valueadding activities that, in the eyes of final customer, do not make
a product or service more valuable (Hines and Taylor 2000). The main pillars of lean
production are management of processes and the integrated logistics flow;
management of relationships with employees, teams, and suppliers; and management
of the change from traditional mass production (Hines 1994). After 1990, lean
production focused away from the shop floor. The value-stream concept evolved and
was able to extend beyond manufacturing to the single company stretching from
customer needs right back to raw-material sources. Womack and Jones (1996)
crystallized Value as the first principle of lean thinking. They define the Lean Enterprise
as a “group of individuals, functions and legally separate but operationally synchronized
companies. The notion of value stream defines the lean enterprise.” As such, lean had
moved away from a merely “shop-floor-focus” on waste and cost reduction to an
approach that sought to enhance value (or perceived value) to a customer by adding
product or service features while removing wasteful activities (Hines et al. 2002).
The mechanism of a lean enterprise is defined as a conference of all firms along
the stream, assisted by technical staff from “lean functions” in the participating firms, to
periodically conduct rapid analyses and then take improvement actions. Womack and
Jones (1996) also note that someone must be the leader of the lean enterprise and
argue that the firm bringing all of the designs and components together into the
complete product should be the leader. However, the participants must treat each other
as equals and the lean system must be transparent (i.e., participating firms should have
the right to examine every activity in every firm relevant to the value stream as a part of
the joint search for waste.). Womack and Jones (1994, 1996) also highlight the fact that
4
a single company will participate in multiple, competing streams with different upstream
and downstream partners in order to learn from companies that think in different ways.
This is a key to continuous improvement. The purpose of the firm itself as a part of the
lean enterprise is to be the link between streams. The links are the means to make
maximum use of technologies and capabilities accumulated by the firm’s technical
functions. They also provide the means for shifting resources between value streams.
3. Case Company
The case company was founded in the early 2010s, based on production of canned fish.
It then shifted its focus into the European market; the case company had been certified
HACCP (Hazard analysis, critical control points) IFS Food Version 6(International
featured standard) and BRC Food Version 6(British retail consortium) Although the
employees’ general level of education is not high, the case company still decided to
implement some lean projects in order to reduce its operational cost, to improve its
financial performance and to better face an increasingly competitive market situation. A
Lean committee was established to facilitate the implementation process, including
building infrastructure, proposing and selecting projects, tollgate review and decisions
related to rewards. As there were many aspects to be improved, the projects were first
prioritized systematically and two projects were selected in the first year. Champions,
usually the leaders of all the departments and supporting units, were then in charge of
monitoring progress and ensuring the success of each selected project. Every year, all
the champions had to propose some candidate projects according to their department’s
KPI (key performance index) and submit them to the committee to be approved. Several
important issues, such as improving customer satisfaction, lowering product defect
rates, reducing recruit cycle time and shortening new product development time were
discussed in the committee. Every possible alternative was prioritized by using the C&E
(cause and effect) matrix. Criteria being considered to select the most critical projects
included the effects on KPI, impact on customers, data accessibility, project hard
savings and the time needed to reach the improvement goal. Among all these candidate
projects, lowering product defect rates was considered the most critical, as it is highly
correlated to KPI and customer impact.
5
Figure 1: Flowchart of mackerel fillets production
4. Methodology
First, a lean team was formed with the people from different departments in the
company, who were knowledgeable and experienced about the products, processes,
equipment, and planning. Lean team leader collected the production data and
generated the process map by studying each stage of the manufacturing processes with
the help from the team members. Strategic areas for implementing lean tools were
identified based on the data and observation. Among many issues related to
6
manufacturing, high waste in raw materials and motion, high consumption of water,
electricity and liquid nitrogen, lack of 5S and Total Productive
Maintenance (TPM) in practice, high machine downtime during changeover and lack of
communications between departments were considered for investigation. Five Key
Performance Indicators (KPIs) were identified: Safety, Quality, Volume and delivery,
Cost, People and Morale, and Environment. The lean projects strongly relevant to the
KPI of the company were carefully and systematically selected and implemented in
order to achieve immediate tangible benefits with minimum investment. A data collection
procedure and structured problem solving technique were established. Boards were
displayed in the shop floor to communicate action lists and control charts. The progress
of lean implementation was regularly reviewed in senior management meetings as well.
5. Results of Lean Implementation
Although a number of lean techniques were applied in the production, packaging
and warehouse areas, in this paper the results were presented based on mainly four
lean principles: Waste reduction, 5S, Single Minute Exchange of Dies (SMED), and
Overall Equipment Effectiveness (OEE).
5.1 Waste Reduction
Data collection on food waste over a six-month period indicated that Interim
storage of cooked fish dewatering over 2 hours, No qualification of the workforce,
Incorrect exploitation of equipment, Lack of manpower, Insufficient space to work the
cooked fish, Poor filling before cooking grids Lack of supervision, Fish small mold
causing duplication of work, and insufficient Storage capacity of refrigeration room
represent the high waste areas (Fig. 2). Waste was generated in the cooling process
more frequently than the other areas in production. With the application of good
practices, the daily due to No qualification of the workforce, incorrect exploitation of
equipment and Lack of manpower were drastically reduced.
Table 1: Data collected to make the pareto chart
Name Value Relative frequency Cumulative frequency
Interim storage of cooked fish dewatering over 2 hours 36 35.78 35.78
No qualification of the workforce 24 23.85 59.64
Incorrect exploitation of equipment 12 11.93 71.56
Lack of manpower 9.5 9.44 81.01
Insufficient space to work the cooked fish 7.9 7.85 88.86
Poor filling before cooking grids 7.8 7.75 96.61
Lack of supervision 2.4 2.39 99
Fish small mold causing duplication of work 1 0.99 99.99
insufficient Storage capacity of refrigeration room 0.01 0.01 100
7
Figure 1: Pareto chart
5.2 5S
The housekeeping tool 5S has been implemented in the daily routines across the entire
site from production to office space to improve the organization of production. 5S areas
of responsibilities were distributed among the employees to own the process. Single
point lessons were learnt from each activity and 5S audits were carried out regularly to
generate 5S score point. New 5S audit boards for production, packing, warehouse, and
office were put in the shop floor to communicate the activities and scores. Although, the
initial score was low (between 30 and 40), gradually the score was improved as shown
in the data collected for six months. Dramatic improvements were achieved in
housekeeping and cleanliness, which was absolutely essential in food manufacturing.
Furthermore, 5S activities generated standard operating procedure, reduced the time
searching for tools, improved 5S awareness, and increased employee motivation
through ownership.
5.3 Single Minute Exchange of Die
African food manufacturing industries are characterized by wide range of product mix,
frequent changeover in the production line and shorter production runs. In some food
processing operations such as in this case company, one product does not run through
a particular production line everyday rather multiple products are manufactured even in
a single day. This shorter production run means frequent changeover, which leads to
increased machine down-time and labor hours. Single Minute Exchange of Die (SMED)
is a lean tool, which can dramatically reduce the changeover or set-up time. Set-up time
is defined as the time between the last good piece off the current run and the first good
piece off the next run. Several SMED activities were carried out at the packing and
forming areas. Using Video analysis and reviewing the process, the changeover time in
8
the forming machine was significantly reduced. By working as a team in a Formula 1 pit
stop style, the operations of cleaning with hot water, standardizing equipment position in
the line and standardizing changeover procedure reduced the changeover time resulting
in better production capability, flexibility, and production efficiency.
6. Discussions
In this study, the lean tools have not only been implemented but also the tangible
benefits to the company have been measured in each case. Although a significant
waste of expensive raw materials was eliminated in the mixing area, it was difficult to
estimate in terms cost saving. However, the activity surely contributed to the
improvement in process yield. The elimination of waste not only helped the company
financially, but also brought considerable environmental benefit, reducing the company’s
carbon footprint. Whist the exact changes in environmental impact are yet to be fully
determined, it is clear that these changes are very much in the spirit of the company’s
long-term mission. It should be emphasized here that financial benefits were achieved
with a minimum amount of investment, which could be paid back in a short time in most
cases within a year. It has been demonstrated earlier that simple changes to the
machines (cutting and seaming) saved a lot of waste in oil and fish. Therefore, working
closely with the equipment manufacturers could be a way forward in order to improve
the machine design for reducing waste, easy maintenance and quick changeover.
Although the general shop floor workers were not familiar with the concept of lean
manufacturing, they quickly learned it through a structured training program and hands
on practical work in the team. This created a learning environment through team
working and a continuous improvement culture in the company by involving everybody
from operator to senior management. This also generated friendly competition between
shifts resulting in improved production efficiency. Finally, the establishment of
continuous improvement team in the company ensured that a long-term improvement
plan was in place for sustaining the lean program and the quest for continuous
improvement was carried on.
The biggest challenges in implementing the lean were the resistance to change from the
operators and personnel changes in production management. The implementation of
lean manufacturing does not happen overnight; it needs time, stamina, better
communication and support from the top management to make the changes a reality.
As the competition is rising continuously, it is absolutely vital to accomplish and sustain
the incremental changes towards achieving the long term stability and competitiveness
in the business.
7. Conclusions
This case study clearly demonstrates that it is feasible to apply lean principles in a fish
canning company. The systematic application of lean tools has started with the waste
elimination in different process steps of the manufacturing cycle across different product
9
range. Waste reduction in Interim storage of cooked fish dewatering over 2 hours, No
qualification of the workforce, incorrect exploitation of equipment, Lack of manpower
Insufficient space to work the cooked fish, Poor filling before cooking grids, Lack of
supervision and Fish small mold causing duplication of work has resulted significant cost
savings for the company and created more value for the customers. The introduction of
5S across the whole factory including office areas has led to a more organized, clean
and safer production area and also increased efficiency due to motivated operators and
shorter time for searching tools. The SMED activities have increased the opportunities
for set-up time reduction leading to quick changeover and shorter lead times. In
summary, the lean activities can facilitate the food company to be competitive in the
market by reducing cost, improving productivity, teamwork, and consistency of product
quality.
Acknowledgments: The supports from the fish canning company and Ibn Tofail
University are sincerely acknowledged to carry out this study.
10
References
Antony J (2008). Can Six Sigma be effectively deployed in SMEs? Int. J. Prod.
Perform. Manage., 57(5): 420-423.
Antony J, Banuelas R (2001). Six Sigma: A business strategy for manufacturing
organizations. Manuf. Eng., 80(3): 119-121.
Antony J, Banuelas R (2002). Key ingredients for the effective implementation of
Six Sigma programmes. Measuring Bus. Excellence., 6(4): 20-28.
Bergman B, Kroslid D (2000). Six Sigma : a revival of the Profound Knowledge of
variation. Proceedings of the 3rd International
Conference on Building People and Organizational Excellence (Aarhus,
Denmark), pp. 260- 266.
Brewer PC, CPA, Eighme JE (2005). Using six sigma to improve the finance
function: Here are some tips for success. Strat. Finance., 85(5): 27-33.
Breyfogle FW (1999). Implementing Six Sigma: Smarter Solutions using
Statistical Methods, New York: John Wiley.
Chen SC, Chen KS, Hsia TC (2005). Promoting customer satisfactions by
applying six sigma: An example from the automobile industry. Qual. Manage. J.,
12(4): 21-33.
Chong PP, Chen YS, Chen CH (2001). IT induction in the food service industry.
Ind. Manag. Data Syst., 101(1): 13-20.
Chung YC, Hsu YW, Tsai CH (2008). An empirical study on the correlation
between Critical DFSS success factors, DFSS implementation activity levels and
business competitive advantages in Taiwan’s high-tech manufacturers. Total
Qual. Manage. 19(6): 595–607.
Efstratiadis MM, Karirti AC, Arvanitoyannis IS (2000). Implementation of ISO
9000 to the food industry: An overview. Int. J. Food Sci. Nutr., 51(6): 459-473.
Fuller HT (2000). Observations about the success and evaluation of Six Sigma at
Seagate. Qual. Eng., 12: 311- 315.
Harry MJ (1998). Six Sigma: a breakthrough strategy for profitability. Qual.
Progr., 11: 60- 64.
11
Hellsten U, KlefsjoÈ B (2000). TQM as a management system consisting of
values, techniques and tools. The TQM Magazine., 12: 238- 244.
Henchion M, McIntyre B (2005). Market access and competitiveness issues for
food SMEs in Europe's lagging rural regions (LRRs). Br. Food J., 107(6): 404-
422.
Hoerl RW (1998). Six Sigma and the future of the quality profession. Qual. Progr.
,11: 35- 42. Kanji GK (2008). Reality check of Six Sigma for Business
Excellence. Total Qual. Manage., 19(6): 575-582.
KlefsjoÈ B, Wiklund H, Edgeman R (2001). Six Sigma seen as a methodology for
total quality management. Measuring Bus. Excellence., 5: 31-35.
Knowles G, Johnson M, Warwood S (2004). Medicated sweet variability: a six
sigma application at a UK food manufacturer. The TQM Mag., 16(4): 284-292.
Kumar M, Antony J (2008). Comparing the quality management practices in UK
SMEs. Ind. Manage. Data Syst., 108(9): 1153-1166.
Kytösaho P, Liukkonen T (2009). Six sigma analysis of SMD feeding parameters
and board assembly quality. Soldering Surface Mount
Lee R (2005). McDonald adopts business practice that made GE famous. Knight
Ridder Tribune Business News, Washington: Mar 8, p.1.
Leea KL, Weia CC, Lee HH (2009). Reducing exposed copper on annular rings
in a PCB factory through implementation of a Six Sigma project. Total Qual.
Manage., 20(8): 863-876.
Linderman K, Schroeder RG, Zaheer S, Choo AS (2003). Six Sigma: A goal-
theoretic perspective. J. Oper. Manage., 21(2): 193-203.
Nilakantasrinivasan N, Nair A (2005). DMAIC failure modes, ASQ Six Sigma
Forum Mag., 4(3): 30-34.
Nonthaleerak P, Hendry L (2008). Exploring the six sigma phenomenon using
multiple case study evidence. Int. J. Oper. Prod. Manage., 28(3):279-303.
Raisinghani MS, Ette H, Pierce R, Cannon G, Daripaly P (2005). Six Sigma:
concepts, tools, and applications. Ind. Manage. Data Syst.,105(4): 491-505.
Spiegel MVD, Luning PA, De Bore WJ, Ziggers GW, Jongen WMF (2006).
Measuring Effectiveness of Food Quality Management in the Bakery Sector.
Total Qual. Manage., 17(6): 691-708.
12
Starbird D (2002). Business excellence: Six Sigma as a management system: A
DMAIC approach to improving Six Sigma management processes. Annual
Quality Congress Proceedings, Milwaukee, pp. 47-55.
Thomas A, Barton R, Byard P (2008). METHODOLOGY AND THEORY
Developing a Six Sigma maintenance model. J. Qual. Mainten. Eng., 14(3): 262-
271.
USOCDD (US Overseas Cooperative Development Council) (2007).
Cooperatives: Pathways to Economic, Democratic and Social development in the
Global Economy, US Overseas Cooperative Development Council, available at:
www.coopdevelopmentcenter.coop/OCDC/CoopPathwaysReport.
Wiklund H, Wiklund P (2002). Widening the Six Sigma concept: An approach to
improve organizational leaning. Total Qual. Manage., 13(6): 233-252.
Zu X, Fredendall LD, Douglas TJ (2008). The evolving theory of quality
management:
Dudbridge M (2011) Handbook of lean manufacturing in the food industry. Wiley-
Blackwell, Hoboken
Higgins KT (2006) State of food manufacturing: the quest for continuous
improvement. Food Eng 78(9):61–70
Anon (2013) Food processing and manufacturing efficiency-competition for
collaborative R&D Funding, 2012
http://www/innovateuk.org/_assets/comp_agrifood_crd_final.pdf. Accessed 1 Feb
2013
Schmidt CJ (2013) Getting the fat out of food manufacturing-a practical approach
to lean manufacturing in the food industry, 2010 EnteGreat, Inc.
http://www.entegreat.com/. Accessed 1 Feb 2013
Beal D (2009) The ABCs of good food manufacturing. Food Safety Magazine,
August/September
Mann R, Adebanjo O, Kehoe D (1999) Best practices in the food and drinks
industry. British Food J 101(3):238–254
van Donk DP (2000) Customer-driven manufacturing in the food processing
industry. British Food J 102(10):739–747
Womack JP, Jones DT, Roos D (2007) The machine that changed the world.
Simon & Schuster, New York
Huxley R, Land J, Lobley M (2011) A Review of the UK food market. Cornwall
Food & Drink Ltd, UK
Anon (2011) Food statistics pocketbook 2011. Department for Environment,
Food and Rural Affairs (DEFRA), UK
13
Anon (2010) Value of food and drink manufacturing to the UK. Institute for
Manufacturing, University of Cambridge, UK