Upload
vodung
View
392
Download
8
Embed Size (px)
Citation preview
Release Notes INCA V700 HF25.docx Seite 1 von 55
Release Notes
INCA V7.0.0 Hotfix 25
Copyright (c) 2014 ETAS GmbH
All Rights Reserved
===============================================================
Release: August 12, 2014
===============================================================
Thank you for using our products. This file contains
important information. We strongly recommend that you
read the entire document. For additional important
information read the corresponding readme documents
and INCA documentation.
We welcome your comments and suggestions.
_______________________________________________________________
Important Information
This hotfix supports the efficient usage of INCA. It contains
the most current bug fixes for INCA.
The functionality of the bug fixes has been thoroughly tested.
However, this hotfix has not been subject to the complete
release tests of INCA. Therefore, it is not possible to
guarantee the usual high quality standards for this hotfix.
ETAS GmbH accepts no further obligation in relation to this hotfix.
_______________________________________________________________
Installation
- Minimum requirement: INCA V7.0.0 installed
- Shutdown all running applications
(especially all ETAS applications have to be closed)
- Start the hotfix installation
- After the installation a reboot is required.
_______________________________________________________________
Update to the “System Requirements” with INCA V7.0.0HF1
Windows 7 SP1 is supported and recommended.
Release Notes INCA V700 HF25.docx Seite 2 von 55
____________________________________________________________________________
Bug fixes
The following issues have been fixed in hotfixes as listed below.
All hotfix software updates are cumulative. The most recent hotfix
incorporates any changes introduced by previous hotfixes.
Often used abbreviations within EHI calls
KIR: Known Issue Report: For severe Problem Reports which occur after
a release, ETAS has introduced the Known Issue Report to inform
affected customer immediately. The current Known Issues of former
versions can be found on the ETAS website: http://www.etas.com/kir
CDM: Calibration Data Manager
EE: INCA Experimental Environment
EHI: ETAS Helpdesk International
LiMa:ETAS License Manager
HF: Hotfix
MDA: INCA Measure and Data Analysis
MIP: Matlab Integration Package
MR: Multi-Recorders
OS: Operating System
OHI: Open Hardware Integration
VSD: Variable Selection Dialog
WB: Walkback, Inca system error
___________________________________________________________________
INCA V7.0.0 HF25
New features and improvements
=====================================
- Support of ES581.4
- New ETAS ETK Tools package
ETK Drivers & Tools V3.12.0 was replaced by ETK Tools V4.0
* The Tools part it now shipped with ETK Tools.
* The ETK drivers of V3.12.0 are now part of INCA 7.0.0HF25 and will be
updated/installed automatically.
* For the first time the ETK Tools V4.0.0 can be installed with help of the
INCA V7.0 Sevice Pack installer (new function, select check box for
installation):
Select ETK Tools and Install (see also ETK_Tools_V4.0.0-Whats-new.pdf).
Known issues and important hints
=====================================
- see HF24 (and HF23)
Release Notes INCA V700 HF25.docx Seite 3 von 55
___________________________________________________________________
INCA V7.0.0 HF24
Known issues and important hints
=====================================
- see HF23
EHI #380601 Connection of ASAP3 to INCA from within the Experiment does
not work if .NET V4.5.0 is installed (no issue with .NET V4.5.1)
Note: Workaround implemented with INCA V7.0.0 HF24 and INCA V7.1.3
Bug fixes and improvements
============================
EHI #367304 Communication error (CCP) during automated write/read test with
powerfail (successor of #361536)
EHI #368659 EE: The error message "Not Enough Memory" is thrown when opening
EE for the second time
EHI #368676 EE Performance: Time required to open EE got slower with
INCA 7.0.0 HF22 with a specific workspace
EHI #368979 CAN UDS: Freerunningmode Switch off/on during measurment leads
to a stall of target server
EHI #372722 Performance improvement for customer specific RAMScope:
Performance during creation of generic measure device in case of
more than 100 measurements
EHI #375601 [WBID625331335] Flashing is not possible
EHI #376561 Start INCA V7.0 after operation of INCA 7.1 without admin
rights (side by side usage) Note: INCA V7.1 has to be installed
EHI #376665 [WBID4188039756] Experiment could not be opened with HF23
EHI #376672 WBID668182908 system error on attempt to open EE
EHI #376847 [WBID1123985822] when select ES610 in Hardware Configuration
EHI #377572 Kvaser devices has no support for ES720
EHI #378046 [WBID4188039756] when open experiment that contains a VUI
EHI #378054 ES610 measurement values are wrong when the workspace
contains a ES595 with FlexRay Monitoring
EHI #378338 INCA sends Tester Present while another service is pending
EHI #380601 Connection of ASAP3 to INCA from within the Experiment does
not work if .NET V4.5.0 is installed (no issue with .NET V4.5.1)
EHI #382876 Pre-trigger-time cannot be saved in the measure file with
XCPonEthernet
EHI #2013401603 UDS flashing is not possible with ECU
Release Notes INCA V700 HF25.docx Seite 4 von 55
___________________________________________________________________
INCA V7.0.0 HF23
Known issues and important hints
=====================================
Important hints for operation with ES581.3:
To support multiple clients with ES581.3 a major/structural change
of INCA, driver and firmware was required.
- When upgrading any of the INCA Versions V7.0 or V7.1 with
INCA V7.0 SP15 or V7.1 SP2 also the corresponding other version
needs to be upgraded to the new version.
- If J2534 is used (e.g. for 3rd party access on ES581.3), an update of
the ES581-J2534 driver to V2.0.7 or higher (part of HSP V10.2.0) is
required.
- Ensure the USB driver is updated to the latest version (part of HSP V10.2.0)
Note: The ES581.3 firmware is automatically updated from the driver (if
required).
Known issues with INCA 7.1HF23 and former hotfixes:
- EHI #349083 Flashing with ES581.3 (and 3rd Party HW) fails - ST_MIN not
respected
Flashing via UDS/KWP with ES581.3 HW might fail, if a CAN frame separation
time (STmin) > 0ms is used.
In this case it might happen that the used separation time is sporadically
lower than STmin.
This is an issue with every 3rd Party HW (Vector, Kvasar, ES520).
It is not issue with ES59x, ES910, ES511.
- EHI #357577 ES581.3: UDS Flashing with ES581 fails
Flashing with ES581.3 HW might fail, if the CAN bus load is high before
flashing is started and the time from last HW initialization of ES581.3
till start of the flashing is too long. To avoid the failure, start
flashing immediately.
New feature - major bug fix
=====================================
- Multiple client support of ES581.3.
- Related ES581.3 calls solved
- Known issue with ES581.3 solved:
> EHI #347726 ES581.3: No measurement via IPETRONIK or CSM possible
if both ES581.3 CAN ports are used.
Bug fixes and improvements
============================
EHI #336147 ES581.3: USBLatency setting slow down flash performance
EHI #344994 ES581.3: CCP Monitoring buffer oveflow at high busload
EHI #347726 ES581.3: No measurement via IPETRONIK or CDM possible if both
Release Notes INCA V700 HF25.docx Seite 5 von 55
ES581.3 CAN ports are used.
Known issue with ES581.3 solved.
EHI #349047 ES581.3: If 2 devices (CCP/Ipetronik) are used and Ipetronik is
initialised as the second device then initialisation fails
EHI #349384 ES581.3: No function of the CSM modules with the ES581.3
EHI #365841 ES581.3: Target Server crashes while measuring with ES581 over UDS
EHI #368813 ES581.3: Gap in Timestamp after 5000 Sec.
EHI #370391 ES581.3: Deterioration of CCP Flashing performance compared to
INCA V700 HF8
EHI #372012 ES581.3: After Flashing of the ECU, the HW initializing do
not respond if the CAN 2 is initialized
EHI #351590 Raster information is not shown in INCA with connected Hardware
Note: Solved with ETK D&T V3.11.0 (part of the SP)
EHI #364983 Targetserver crash during flashing
EHI #365264 Doubled display of ES921-device and not present ES920 in
HWC-search if CSM AddOn installed
EHI #365839 Error indication on ES1000 after installation Partner_addOn
products
EHI #367438 and #367690 EE: Measurement with abs(x) not updated in widgets
EHI #367801 CSM Addon did not run properly with used INCA command
updateFromSearchResultUseCase- Msg: Invalid use case
EHI #368296 Difference in CDM compare is not detected
EHI #371147 MPM actions for ETK S6.0 seem to do incorrect copy actions
Note: Solved with ETK D&T V3.11.0 (part of the INCA SP)
___________________________________________________________________
INCA V7.0.0 HF22
Known issues and important hints
=====================================
ES581.3: See HF19.
Bug fixes and improvements
============================
EHI #97911 CSE: Wrong state in VSD after adding label with same name from
different device to CSE
EHI #323817 Hotline Contact Information outdated
EHI #326587 ES690 - HW init issue with CANMon and CCP at one CAN bus if not
ES690 default baud rate (500kBaud) is used
EHI #347079 CAN-Monitoring does not change initial baud rate setting
EHI #347178 Faulty slew icon displayed on the dataset after reading the
Release Notes INCA V700 HF25.docx Seite 6 von 55
hex file.
Note: Already solved with INCA V7.0.0HF21.
EHI #347835 ES593: After disconnect and reconnect Ethernet, the
CAN Monitoring on CAN1 is no longer possible
EHI #348732 CDM: Dependent labels are unexpected computed when using A2L
and Data Transfer File
EHI #349096 [WBID1309351448] System error during MCE label configuration
Note: Requires INCA AddOn MCE V1.1.3 (part of INCA 7.0.0SP14)
EHI #350243 INCA memory increases as run MCD3 tests causing PC to freeze and
INCA to crash
EHI #350908 Set the same serial number for two different ES581.3 devices
EHI #351870 [WBID1811049737] System error during INCA session
EHI #352649 CAN Monitoring data timestamp jumps during recording
EHI #352708 [WBID3185843499] at opening experiment or when starting HWC dialog
EHI #353955 [WBID4070127963] Walkback when open experiment
EHI #354194 LCA: Cannot write StringArrayParamVar
EHI #355040 If SEED_AND_KEY() was called twice, the second call always
returns "0"(error).
EHI #355604 After saving an experiment the modified values are getting lost
EHI #356804 Data samples missing from ECU with XCPonCAN measurement in the
mdf-file
EHI #356922 [WBID2799303568] when search for HW in HW editor
EHI #357188 IPM Server configures ETAS network in the last known CN subnet
address range
EHI #357387 [WBID669325502] System error during INCA session
EHI #358113 Recorder file is not saved using ASAP3
EHI #359314 [WBID3087534066] Sporadic WB during INCA session
EHI #359583 ErrorCode 517 when save database with INCA 7 type
EHI #360410 [WBID3489611665] System Error during INCA session
EHI #361536 [WBID3417850026] with SW bundle 24 during EEPROM write/read test
with power fail
EHI #362104 IPE Devices would not recognized due start the EE
EHI #362942 INCA lock up when perform checksum routine after flash on Win 7
PC.
EHI #363548 After an error in RCI2 interface, IncaGetLastError returns
"No Error found", which is wrong
Release Notes INCA V700 HF25.docx Seite 7 von 55
EHI #364161 Connection to ECU broken after automatic firmware check
EHI #364177 Icon of OnlineFirmwareCheck incorrect in HWC for
ES592/ES593/ES595/ES581
EHI #364514 [WBID59071569] while opening INCA Experiment via EE
EHI #366195 INCA 7.0 HF20/21 VCRedist 2010++ 32bit needed
Note: Solved with ETK D&T 3.9 and subsequent (part of SP14)
EHI #366304 Opening HWC of a LIN device without an assigned project causes
an OHI Error Message
Note: Solved with INCA AddOn LIN V7.0.3(part of SP14)
EHI #366579 Optional COM API Logging with time stamps - backport INCA V7.1
EHI #368402 Installation: If the "Tools" from ETK Drivers & Tools are
installed and the .NET V4 package is missing, then the installation
is no finished correctly
EHI #368437 [WBID2799303568] when search for HW in HW editor
EHI #368460 Redo does not work for Scalar Table Editor
EHI #368561 ETK_D&T 3.10.0 Distab 17 wrongly configured in case of doubled
addresses - KIR issue solved.
Note: Requires INCA-AddOn ETK D&T V3.10.1 (Part of INCA 7.0 SP14)
EHI #2012406038 [WBID3218871388] solved - backport from INCA V7.1.1
EHI #2013401387 INCA freezes after UDS flashing with ES581.3
___________________________________________________________________
INCA V7.0.0 HF21
Known issues and important hints
=====================================
ES581.3: See HF19.
Bug fixes and improvements
============================
EHI #350411 ToolAPI issue: it is not possible to add ES581 device via
GetDeviceDescription method
Script adapted. No product change.
EHI #350733 CDM comparison in Inca 7 with few labels is very slow
EHI #352933 [WBID1068249489] Exit due to error: 60 - Exit due to walkback
when a certain experiment is being selected in the database tree
EHI #353786 MeasureCal shows wrong value if calibration was changed by
EE instrument
EHI #354101 Slews: Slew behavior changed and icon is not being displayed on
the proper data set
Release Notes INCA V700 HF25.docx Seite 8 von 55
EHI #354189 Additional CAN Transmit device is added when perform replace
EHI #354344 INCA V7.0.0 [WBID2252893887] INCA V7.1.0 [WBID3914582808] when
opening experiment
Solved for both INCA versions.
EHI #354573 Not possible to display the process point
EHI #355071 When selecting BOA hardware in BUSMASTER, the HW is not found
EHI #355263 MCD 3 MC V2.2 : Internal Error at IMCCollectors.Add
EHI #355641 Wrong direction of changing phys value
EHI #356052 Unexpected Monitor-log entry after using
Convert Experiment --> Write Template
EHI #356055 Conversion file uses wrong ASAP2_VERSION
EHI #356199 Server Busy message and Walkback encountered when using
UFE "Force Running Reset"
EHI #357131 CDM WBs ([WBID2415885070], [WBID4035783185]) after API-Access
EHI #358148 WBID3642544362 System Error reading from file in CDM
EHI #358310 [WBID3269616446] Memory optimization message and walkback
when open and close experiment multiple times
EHI #358625 [WBID177740905] when opening experiment
EHI #359167 [WBID23588784] INCA V7.0.0: System error opening Experiment
EHI #359761 Undo from Calibration Actions in the Scalar Table Editor does
not work for Grouped Devices
EHI #362219 OHI Error Message when open EE with Lin Device
Note: Requires INCA Add-On LIN V7.0.2 (part of INCA V7.0.0SP13)
EHI #362574 FlexRay EE is not usable because no label is available
Note: Requires INCA Add-On FlexRay V7.0.7 (part of INCA V7.0.0SP13)
EHI #363688 In Asap3 every measurement loop creates old + new file
(partly solved)
EHI #87145 Performance improvement: INCA consumes too much RAM using MCD3
EHI #92245 System Error at copy and paste of folders
EHI #2012405737 The name of raster is not displayed completely
EHI #2012405982 [WBID585474223] System error when add Daisy chain device
Already solved with INCA V7.0.0SP12.1 (together with the updated
DaisyChain AddOn V1.3.4)
___________________________________________________________________
INCA V7.0.0 HF20
Release Notes INCA V700 HF25.docx Seite 9 von 55
Known issues and important hints
=====================================
see INCA V7.0.0 HF19
Bug fixes and improvements
============================
EHI #356818 XCP-Download to working page (WP) is not possible
___________________________________________________________________
INCA V7.0.0 HF19
Note on May 06, 2013
- INCA V7.0.0HF19 was not released on the ETAS download page due to issue
EHI #356818 XCP-Download to working page (WP) is not possible
with INCA V7.0.0 HF19. This is solved with INCA V7.0.0 HF20.
Known issues and important hints
=====================================
- ES581.3:
> EHI #347726 ES581.3: No measurement via IPETRONIK or CSM possible
if both ES581.3 CAN ports are used.
Multiple clients are not supported.
Only one SW application can set the CAN configuration, e.g. baudrate, for
the ES581.3.
The application that accesses the ES581.3 first is able to configure each
CAN channel independently. The application accessing the ES581.3 second,
e.g. a third party SW or an INCA AddOn, can only reuse the settings made
by the first application.
If the HW module that the second application accesses needs a configuration
that differs from the configuration already set, the use of that module
will fail.
Known issue solved
============================
EHI #351788 Time leap using ES580
During a measurement of long duration, a time stamp jump in the recorded
measure file(s) may occur.
The issue depends on the duration the HW is plugged into computer
(and timer increasing).
Affected HW: All supported Vector modules (e.g. ES580, VN7600, CANCase XL,
CANCard XLe, CANLink, CANCard X, CANCard XL)
Bug fixes and improvements
============================
EHI# 98564 It is not possible to initialize ES595 if only Ipetronik is
configured
EHI# 2010403395 Focus after deleting DB items missing, add elements icons
active
Already solved with INCA V7.0.0HF18
Release Notes INCA V700 HF25.docx Seite 10 von 55
EHI# 2011403903 A2L with more than 26 "RESERVED_DISTAB_MEMORY" entries cannot
be assigned to ETK device
EHI# 2012404400 Vertical scroll bars in EE are inactive
EHI# 2012404872 Limited ERAM: If "output" component of a MAP is write-
protected, it is not possible to calibrate axises from the combined editor.
EHI# 2012404949 [WBID906108180] when opening experiment
Already solved with INCA V7.0.0HF18
EHI# 2012405549 [WBID1080142799] during INCA session
EHI# 2012405759 Dependent parameter get not calculated correctly after copy
action in CDM
Already solved and shipped with INCA V7.1.0HF17
EHI# 2012405799 MCE-Error 0x80001003 when configuring the variables for
EtherCAT communication.
Message on the testbed side is "Unable to Toggle to SAFE-OP State on
FULI Device"
Same issue as in Call #348908.
Solved with INCA-MCE V1.1.2 (required, part of SP12).
EHI# 2012405806 Focus to select variables is lost when working with ALT-TAB
EHI# 2012406004 Re-Init with CAN-Monitoring doesn't work
EHI# 2012406315 [WBID4070127963] while open experiment
Already solved with INCA V7.0.0HF18
EHI# 346634 No measure data displayed in INCA on a XCP on Flexray ECU -
Incorrect response to error assigning DAQ list slots
EHI# 347695 INCA hangs during XCP init
EHI# 347835 ES593: After disconnect and reconnect Ethernet,
the CAN Monitoring on CAN1 is no longer possible
EHI# 348002 Not possible to read a given Fibex file into INCA database
INCA FlexRay AddOn V7.0.6 required.
EHI# 348111 [WBID2758593614] during INCA session with given project
EHI# 349123 FlexRay Monitoring loses PDUs
Note: Solved with FlexRay AddOn 7.0.6 (required)
EHI# 349506 [WBID4070127963] when opening the experiment
EHI# 349616 CDM freezes or creates fatal error
Solved with #350757
EHI# 349662 GPS data recorded by INCA V7.0.0 and ES720 (V7.0.0) respectively
are incorrectly displayed in MDA
EHI# 349770 [WBID977812319] if an output signal is assigned to the ES930
in the EE
Already solved with INCA V7.0.0HF18
Release Notes INCA V700 HF25.docx Seite 11 von 55
EHI# 350230 If last used database is on a network share an error occurs
on opening Inca
EHI# 350406 INCA V7.0.0 HF18 beta 6 does not start
EHI# 350503 IPETRONIK modules loses connection to INCA when ECU goes into
power off
EHI# 350757 Memory management - support of huge project improved
EHI# 350950 INCA feature 'ETK Reset Security' does not work anymore for
generic ETK
EHI# 351063 [WBID2428229303] STRG+U RBDataVector does not understand axis
Already solved with INCA V7.0.0HF18
EHI# 351310 CDM can not read DCM Lists
Already solved with INCA V7.0.0HF18
EHI# 351582 [WBID2428229303] occurs when returning to reference values
via "ctrl+u" shortcut
Already solved with INCA V7.0.0HF18
EHI# 351624 [WBID518082257] when perform "Write Template" operation
EHI# 351629 [WBID2428229303] error message when changing the calibration
value via "ctrl+u"
Already solved with INCA V7.0.0HF18
EHI# 351788 Time leap using ES580
"Known issue solved
Details see "known issue solved" above.
EHI# 351821 ES910: Non UTF-8 characters (Unicode) in configuration XML not
supported by ES910 API
Solved with INCA Add-On MCE V1.1.2 (required)
EHI# 353161 Error "It is not allowed to wire values from FULI-LUNs into a
recorder [60835]"
... in ASAP3 when adding values to INCA Recorder (not to FULI LUN)
EHI# 353252 [WBID448902737] CDM: The setting ASAM2MC of the compare mode
leads to WB during listing of different items
EHI# 353255 Impossible to start INCA after installing SP10 or SP11
EHI# 353283 No Ethernet connection to HW possible, if the search for HW or
init is started, during the windows 7 network identification task is active
EHI# 353499 IPM: DHCP-Check when the DHCP Server provides IP addresses in
the APIPA range reserved by Microsoft
The check is switched off (like INCA V7.0.0HF14 and former versions).
The pre-condition is, that the NIC used for IPM Server has the
IP address in APIPA range (169.254.0.1 - 169.254.255.254).
___________________________________________________________________
INCA V7.0.0 HF18
Known issues and important hints
Release Notes INCA V700 HF25.docx Seite 12 von 55
=====================================
New known issues:
- ES581.3:
> EHI #347726 ES581.3: No measurement via IPETRONIK or CSM possible
if both ES581.3 CAN ports are used.
- No measurement if 2 CANs are used, one for INCA (e.g. CCP), another
for a CSM or IPETRONIC module.
- Another issue if baud rate of two CAN channels is different.
Currently only one baud rate supported. If a second CAN is initialized
with a second baud rate, the baud rate of the first CAN might be
overwritten.
- Recommendation: Use only one CAN-channel
- New ES581.3 devices with new Serial Numbers (S/N)
and update of all ES581.3 devices
- see important hints of INCA V7.0.0 HF17
(Note: update could be done with HSP V9.9.2 as well)
EHI #347824 Adobe Reader V11.0.1 block the command ''Variable Documentation''
This is due to a missing/wrong registry setting with Acrobat 11.
Workaround: Change corresponding Acrobat registry setting until the
issue is solved by an Acrobat update.
E.g. add the following to an acrobat11.reg file and execute it (double
click) to change registry-setting or change it completely manually:
Windows Registry Editor Version 5.00
[HKEY_CLASSES_ROOT\acrobat\shell\open\ddeexec\application]
@=""AcroViewR11""
Known issue solved
============================
EHI #2012403746 [WBID2233574518] during CCP over ES910 measurement
Known issues
reported with INCA V7.0.0 SP7(HF13) and HSP V9.7.0
On high performance PCs (normally running Win 7 64Bit) some technical
limitations could occur using ES910 and CCP concurrently
on several CAN channels with high bus load.
In case of ES910 and several CCP-ECUs it is still recommended to
use INCA V7.0.0 SP6/HF12 together with HSP V9.6.1
It is planned to solve the issue with the next version.
Bug fixes and improvements
============================
EHI #2011402629 Column width changes
Already shipped with another solution with INCA V7.1.0 HF6
Release Notes INCA V700 HF25.docx Seite 13 von 55
EHI #2011404715 CDM Compare of data sets takes 15 minutes
EHI #2011408826 WB [1330975451] while opening experiment from older
INCA version V5.4.1
EHI #2012403455 Errors during import of a CDF file as a dataset
EHI #2012403746 [WBID2233574518] during CCP over ES910 measurement
Known issue reported with INCA V7.0.0 SP7(HF13) and HSP V9.7.0 solved.
EHI #2012404097 Default recorder does not start after removing variables in
the experiment
Already solved with INCA V7.0.0 HF16.
EHI #2012404162 [WBID1523572377] INCA stops completely during sending the
stop during an automated sequence
EHI #2012405160 Segment wise page switch leads to inconsistent data in ECU
EHI #2012405281 Measurement values are irregularly updated in the EE during
visualization and recording
Already shipped with INCA V7.0.0 HF17.
EHI #2012405301 Calculated Signals get not loaded in the yT oscilloscope
EHI #2012405399 Invalid analog signal over ES595
EHI #2012405502 CDM: Copy of array shows no error even if hard bounds exceeded
If a cell of an array exceeds the hard bounds, no error or warning
is shown and the cell value is clipped to the hard bounds.
EHI #2012405547 Wrong value is displayed in experiment
EHI #2012405678 Experiments hangs during measurement
EHI #2012405708 [WBID1789765672] During windows configuration in the
experiment, moving a window with the courser
EHI #2012405843 [WBID1931694180] when opening the EE
EHI #2012405893 [WBID2637493711] while reading HEX file.
EHI #2012405918 It is not possible to import Exp-file with dataset (created
via ToolAPI) to the existing data base
EHI #2012406003 Display of variables in GUI stops after some time when
using "Timestamp_supported" in A2L file.
EHI #2012406039 XPonEnt communication is not possible after switching between
ECU-project - it is not possible to use WP and RP
EHI #2012406095 [WBID3727437600] accessing or using the keyboard shortcut
CTRL + T for changing view of a map editor
EHI #2012406102 Measuring buffer overflow when using a special experiment
on a laptop with XP SP3
EHI #2012406136 [WBID475944959] during a INCA session
Release Notes INCA V700 HF25.docx Seite 14 von 55
EHI #2012406421 CSM module ADMM incorrectly represented in the hardware
config editor with 8 channels instead of 4 channels
EHI #2013400197 [WBID3920615049] walkback occurs while converting a dat file
to an ASCII file
Workaround: MDA can be used for convert to ASCII.
EHI #279278 It is not possible to initialize ES595 if only Ipetronik is
configured
Note: Improved to the same behavior like with INCA V6.2.1HF21 and subsequent.
But System-Mapping-Dialog still not provided automatically
with ES690/ES910/ES5xx and Ipetronik-AddOn.
Workaround: Execute SFH (search for hardware) manually.
EHI #309455 Using a FORMULA CompuMethod leads to error on measurement
start with MCE
EHI #311239 A2L Parsing Error when using the expression "/include file.aml"
EHI #323450 [WBID1845261986] OrderedCollection does not understand
getDefaultPhysValueFor:formula
EHI #326545 [WBID152773687] EtasEnhancedDatabaseDialog does not understand
writeUserOptionsToIniFile
EHI #330008 Variable find feature does not highlight the expected variable
EHI #333431 Reading of A2l File with XCPplus(AML V2.0) definition not possible
EHI #335928 ASAP2 LAYOUT ROW_DIR not supported
Support of the ASAP2 keyword LAYOUT (for AUTOSAR project using
Measure Arrays)
EHI #337731 CDM copy reports no errors but variable is not copied
EHI #338471 ES581.3 Flash performance: Duration of the flashing action
lies between 60 seconds and 480 seconds
EHI #339019 [WBID2647750935] when open special workspace
EHI #340883 [WBID1168902146] after changing "Overlay Properties"
EHI #342186 ASAMMCD3MCV22: WriteReadRecoder.deactivated doesn't stop the
running Recording.
-> Error eRT_NOT_ALLOWED_IN_THIS_OBJECT_STATE at
oLogicalLink.DisconnectFromModule()
Solution was already shipped with former INCA V7.0.0 HF15/16
EHI #343832 [WBID3701453531] when open a special workspace
EHI #344193 CAN Monitoring J2534 ES581 Timestamp not correct after about
4000 sec
Requires also driver update for J2534 and ES581 with HSP V9.9.1
EHI #344560 [WBID3276210548] when clicking on special ECU
EHI #345030 [WBID419512931] when open special EE
EHI #345457 [WBID3169589889] when setting alias name via menu in HWC
Release Notes INCA V700 HF25.docx Seite 15 von 55
EHI #345586 It is not possible to read a2l file with Unicode(UTF8) with
BOM due to error
EHI #346112 Cannot open database from "not connected" network share
EHI #346266 COM API - CDM runs out of memory when compare is started
via COM API
EHI #346661 A2L file cannot read in with an additionally AML notation
in the MEMORY_SEGMENT section.
EHI #346758 Win7 (x64) 512 Data file loop detected INCA DB crashed
EHI #347236 [WBID3335207883] when using CSE
EHI #347321 Adaptive maps of given project not updated with SP V9.1
EHI #347388 ASAP3-crash using "GET USER DEFINED VALUE LIST"
EHI #347399 [WBID2200047011] when open special EE with ASAP2
EHI #347411 VIRTUAL_MEASUREMENT - Back port of the support of
IF_DATA CANAPE_EXT to INCA 7.0
EHI #347455 [WBID579070364] While open a HTML File in CDM a system
error occurred
EHI #347456 Crash solved: New method to display icons in case of corrupt
a2l-file
EHI #347458 The output configuration of FLOAT32 does not save phys bottom/top
values - enhancement of #338687
EHI #347587 CDM shows always an message in the monitor-window if a filter
is in use
EHI #347973 [WBID579070364] while open a HTML file in CDM
EHI #348008 [WBID2601018573] + [WBID2637493711] during loading of experiment
EHI #348009 [WBID2637493711] while loading an ECU-Project(A2L+Hex)
EHI #348378 [WBID1434558840] and [WBID272884890] when navigation in ECU
EHI #348732 CDM: Dependent labels are unexpected computed when using A2L
and Data Transfer File
EHI #349123 FlexRay Monitoring looses PDUs
Note: Solved with FlexRay AddOn 7.0.6 (required; will be released soon)
EHI #349251 Change markers missing for shared axis in "Combined Editor",
if data is read in by calibration file
EHI #349402 [WBID821851098] when double click on ECU of a INCA V7.1.0 project
imported in INCA V7.0.0
EHI #349510 .Net crash of VSD if change variable to inactive
EHI #349704 [WBID1200184091] Daimler Extensions: Moving Ctrl-F dialog in
project causes WB
Release Notes INCA V700 HF25.docx Seite 16 von 55
EHI #349839 After starting visualization, size of "Measure Table" is changed
and values are not visible
EHI #349841 Long Name is not any longer copied when copy Measure Labels in
ASAP2 Editor
___________________________________________________________________
INCA V7.0.0 HF17
Known issues and important hints
=====================================
- New ES581.3 Devices with new Serial Numbers (S/N)
and update of all ES581.3 devices
Newly shipped ETAS ES581.3 devices (S/N >40000) have an extended range
for the serial numbers. INCA V6.2.1 HF33 and INCA 7.0HF13 and subsequent
releases support these new devices (see EHI #332119 Serial number
range for ES581.3 for recognition as ETAS device extended)
!!! Important !!!
There is an update with HSP 9.9.1 or higher required to support ES581.3
devices
(new and old versions) and take advantage of the fixes shipped with this HF
(INCA V7.0.0HF17)
Please install the ES581 USB Drivers and J2534 Drivers shipped with HSP V9.9.1
Note:
- New devices (S/N >40000) cannot be downgraded to a firmware version
lower than HSPV9.6.1
- If the updated ES581 - drivers are not installed, INCA might not find or
operate the new devices with extended serial numbers (all new shipped
devices affected).
- The devices might not operate correctly with INCA V7.0.0HF17 or higher,
if the J2534 driver is not updated with HSP V9.9.1 or higher.
Bug fixes and improvements
============================
EHI #2011404662 INCA generates inconsistent message counter on
CCP communication
EHI #2012402317 ECU connection breaks during Flash
EHI #2012402379 Calibration of Mappings with several cells using ES581.3
leads to communication loss to ECU
EHI #2012403687 INCA hangs when working with a huge datasets in CDM
Partial solution shipped with INCA V7.0.0 HF15. Now further improved
for Win XP and Win Win7.
EHI #2012404058 LCO V5.1.2 / EE3.3.1/1: Crash - Index was out of range
EHI #2012404162 [WBID1523572377] INCA stops completely during sending
the stop during an automated seqence.
Release Notes INCA V700 HF25.docx Seite 17 von 55
EHI #2012404266 [WBID4157865031] Opening EE
EHI #2012404303 ProF compressed flashing via UDS not possible.
To flash compressed data via UDS it is necessary to set the end
address to 0. In this case Prof returned an error: Memory area 2
not defined in CNF file."
EHI #2012404317 ES_I710.65: Replace System with ES520 by ES581.3 not possible
EHI #2012404399 [WBID667152105] Inca crash on reimport saved csv Excel file
with map
EHI #2012404414 Flashing is not possible with ES581.3
EHI #2012404474 Flashing using ES581.3 failed
EHI #2012404704 CCP inconsistency during CCP download
EHI #2012405081 "Exception occurred" error after WriteReadRecorder.
Deactivate() when the WriteReadCollector was activated only
(start-stop commands were not used)
EHI #2012405102 [WBID2986428855] INCA crashes on Win 7 PC when one tries to
select the network drive via its letter (Registry Entry
"EnableLinkedConnections=dword:00000000")
EHI #2012405115 The output configuration of FLOAT32 does not save phys
bottom/top values
EHI #2012405273 [WBID1793154450] System error when loading CDFX file in
CDM as source
EHI #2012405341 ES580: INCA frozen for 2-3 sec. if switched between
layers and notebook in use
EHI #2012405372 No Flexray value shown in INCA
EHI #2012405437 CCP inconsistency with ES581 device
EHI #2012405471 Registration problem of INCA components if installation path
includes spaces - No proper operation possible
EHI #2012405552 PaCo files written with false SW-CS-ENTRY attribute
The time attribute is written with "t" instead of "T".
EHI #2012405608 [WBID3313097948] System error while variable selection
EHI #2012405612 INCA does not start at all due to issue with Standard
Dialogs used by ASCET and INCA on the same computer
Same like #341837
"
EHI #2012405683 [WBID1474063629] System error during INCA session
EHI #2012405739 [WBID238867121] Opening the VSD
EHI #2012405759 Dependent parameter get not calculated correctly after
copy action in CDM
EHI #2012405769 INCA crash at PARAMETER FOR VALUE ACQUISITION command of
Release Notes INCA V700 HF25.docx Seite 18 von 55
ASAP3 session with the large experiment
EHI #2012405778 [WBID3313097948] While variable selection
EHI #2012405848 "Complexity validation" error on ES720
EHI #2012405860 XCPonEth + CCP+CAN-Mon: Time offset in the measure file
EHI #2012405896 Time delay in Can-monitoring and XCP measurement via ES581.3
EHI #2012405945 ES720 - Stop-Trigger doesn't work . Blocking for ES720-UseCase
EHI #2012405993 VUI: Order of variables when reading the file *,names is
not be considered
EHI #2012406026 [WBWBID3109871623] WB during start of EE
EHI #2012406078 CDM shows "R" names but a user option = ""D" only"
CDM - function view: If a user option "shows D variables only"
is active and the function view is active and the function with
"R" and "D" variables is selected INCA should display the
"D" variables only but the axis ( --> "R" variable) is visible "
EHI #2012406195 [WBID3754308073] CDM: WB after select all diff. signals
EHI #329770 Already selected filter in VSD of Trigger Editor does not display
signals in experiment
EHI #335370 [WBID906108180] Walkback when auto remap rasters in experiment
EHI #338050 ES581.3: Error Message: Queue event - the receive queue has
overflown if you calibrate a big number of calibration values
EHI #338884 .NET Framework error when change record state and sort in
Variable Configuration dialog
EHI #339723 ES720: CCP connection not being restored every time after
ECU power cycle
EHI #339793 ES591/ETK D&T V3.6.0: No measurement possible unsing all rasters
Solved with INCA V7.0.0HF17
EHI #340377 CAN, CCP: No automatic reinit after multiple off on ECU KL15
EHI #340723 [WBID3269616446] CDM: WB when performing copying with large
datasets and multiple destinations
EHI #340827 ES6xx data drop outs after about 40 minutes of recording
EHI #341031 When using "Display Mode" it is possible that after clicking
into graphical area not the expected area is shown
EHI #341050 ES590; COM: HWInit & Start Recording fails
EHI #341177 Not possible to assign project to XCP device if a2l was read
using Shift_JIS encoding
EHI #341186 Unexpected behavior when using "Multi Selection" in
the graphical area
Release Notes INCA V700 HF25.docx Seite 19 von 55
EHI #341309 Performance: INCA VRAM consumption increased
EHI #341784 ES415 Online Help: Extend map file for context sensitive mapping
EHI #341792 [WBID823754594] when saving experiment after setting some
variables in VUI->Osci inactive
EHI #341797 When using a XCP ECU with a HWC with a Ipetronic device,
the XCP data has time-jumps of about -2 seconds
EHI #341837 Installation : INCA doesn't start
Same like #341107
EHI #343673 Targetserver crash in a1b_CCPCan.dll
EHI #343884 The Windows Timer may have a too low resolution for the
targetserver
Within the targetserver it is ensured that the time resolution used
for the 'Sleep()' functionality is at least 2 ms.
EHI #344285 ASAP3: PARAMETER FOR VALUE ACQUISITION returns with error
"Unable to obtain a raster for the following variables (check your
ASAP2 file): [60828]" by calculated Signals
EHI #344355 [WBID626530968] after try to save EE (inactive)
EHI #344939 Sub VUIs are not any longer used
Side effect of INCA V7.0.0HF15 solved.
___________________________________________________________________
INCA V7.0.0 HF16
Note: INCA V7.0.0HF15 was not released at the ETAS Download Page
due to found side effect EHI #2012405779.
Known issues
=====================================
See INCA V7.0.0 HF15, please.
Bug fixes and improvements
============================
EHI #2012405882 EE form 100Mbit_ETK_AML cannot be used with XETK_AML-project
The DAMC4 - compatibility-checks (8Mbit vs 100Mbit) in loading or saving
the EE were removed.
EHI #2012405779 Flash process fails after erasing the flash.
Side effect introduced with INCA V7.0.0 HF15 solved.
___________________________________________________________________
INCA V7.0.0 HF15
Note: INCA V7.0.0HF15 was not released at the ETAS Download Page
Release Notes INCA V700 HF25.docx Seite 20 von 55
due to found side effect EHI #2012405779.
Known issue
============================
- KIR PR 2012404415 (also published on the ETAS Download Center)
is solved with INCA V7.0.0 HF15
- see also known issues of the SP9 release notes
- New ES581.3 Devices with new Serial Numbers
Newly shipped ETAS ES581.3 devices (S/N >40000) have an extended range
for the serial numbers. INCA V6.2.1 HF33 and INCA 7.0HF13 and subsequent
releases support these new devices (see EHI #332119 Serial number
range for ES581.3 for recognition as ETAS device extended)
!!! Important !!!
There is also an firmware-update with HSP 9.7.0 or higher required to
support new ES581.3 devices.
Please install the ES581 USB Drivers (V2.4.16) and J2534 Drivers (V2.0.1)
or higher versions. New devices (S/N >40000) cannot be downgraded to a
former firmware version with HSPV9.6.1
Note:
If the updated ES581 - drivers are not installed, INCA will not find or
operate
the new devices with extended serial numbers (all new shipped devices
affected).
Bug fixes and improvements
============================
____________________________
KIR Issue solved:
- EHI #2012404415 Calibration outside from hard bounds possible
if the defined range includes a singularity
KIR PR 2012404415 (published on the ETAS Download-center)
If
within the A2L a COMPU_METHOD with a (possible) singularity (1) is defined
(e.g. f(x)=1/x)
AND
this COMPU_METHOD is used to calculate the hex value out of phy values
of a parameter
AND
the defined range (including boundaries) wrongly includes the singularity
of this COMPU_METHOD (here x=0; e.g. a range [0, 2000])
AND
the value (hex or phys) of the parameter is changed outside the defined
boundaries within the experimental environment of INCA (here: e.g. x=-20)
THEN
INCA does not detect, that the value of the parameter is outside
the boundaries and the value is wrongly transmitted to the ECU.
Note: (1)Singularity respectively pole of the function is a point at which a
given mathematical object (function) is not defined [e.g. division by zero];
infinity; f(x)=1/x at x=0)
Release Notes INCA V700 HF25.docx Seite 21 von 55
Given: f(x)=A(x)/B(x)=(ax^2 + bx + c)/(dx^2 + ex + f);
f(x) has singularities, if B(x)=dx^2 + ex + f=0 (B(x) is zero).
The defined range (including boundaries) shall not include singularities
(e.g. in the example [1, 2000])
Affected INCA Versions: V6.2.1 and V7.0.0 (checked) and lower versions.
Workaround:
Change the A2L file so that the valid input range, including boundaries,
does NOT include a singularity(1) of the given function. As a result all
output values of the function and the boundaries can be calculated and
result is within a valid range of ECU (but not infinity).
(1) Singularity: see description.
________________________________________________________
Extensions - Compatibility with INCA 7.1.0
EHI #2012403685 EE created in INCA V7.1.0 is indefined in INCA V7.0.0
EHI #328357 Suppress new osci VUIs in INCA V7.0.0
EHI #331076 Enable Import of Supported Objects in INCA V7.0
EHI #336734 Import of VUI having new osci in Sub-VUI
________________________________________________________
Bug fixes
EHI #1004542 [WBID2751407788] Walkback when launch experiment environment
EHI #1004565 CAN Mon stops calculating trigger conditions and uses wrong
timestamps
EHI #2010403553 Database does not contain all datasets after repair action
Already solved with INCA 7.0.0 HF10.
EHI #2011405953 If the background task is activated in CDM, the RAM
consumption is high
EHI #2012401139 Performance generating measure data files improved
EHI #2012402379 Calibration of Mappings using ES581.3 and CCP speed up shall
work together
EHI #2012402831 Start of Measuring Monitor from HWC with GPS mouse, resulted
in blue screen
EHI #2012402835 CCP download and upload memory size does not match
Was already solved with INCA 7.0.0 SP8/HF14.
EHI #2012402989 Automatically recognition (search for hardware) of HW of
3rd-party CAN - modules extended to all found system types (ES580, ES581,
ES590, etc.)
EHI #2012403110 [WBID3472338849] System error during INCA session.
Follow up of #2012403110 (see HF13): Issue completely solved for another
use case than reported.
Release Notes INCA V700 HF25.docx Seite 22 von 55
EHI #2012403300 Adaptive maps are not updated
EHI #2012403313 When a VAL_BLK is requested during a asap3 session,
the asap3.exe crash.
EHI #2012403674 Error message "Parsed file does not contain a valid ASAP2
project description" when adding ES1303 + Japanese language
Error message appears when adding ES1303 at the hardware configuration
window and channel setting tab is also blank in INCA V7 of Japanese
environment. (After change the language setting to English, this error
does not appear.)
EHI #2012403687 INCA hangs when working with a huge datasets in CDM
Solved for Win 7 (but currently not for Win XP).
A complete solution planned for the next HF.
EHI #2012403700 [WBID18069440] WB occurs when adding calibration on a new
calibration scenario
EHI #2012403738 Calibration change markers is not displayed after download
for a single page CCP ECU
EHI #2012403872 Adaptive characteristics not updated in INCA experiment
after read from file
EHI #2012404129 [WBID347956746] while opening experiment due to "Inactives"
in the EE (Calibrations and Measurements)
EHI #2012404193 Inconsistent CCP command counter received error if starting
MPM window after opening EE and finishing initialisation (ES581)
EHI #2012404334 [WBID987567384] WB occurs when opening EE with Japanese
characters in measurement file path setting
EHI #2012404373 Limited ERAM: A MAP should be write-protected if enough
ERAM blocks are not available
EHI #2012404375 Limited ERAM: A MAP data and axis data should be write
-protected if enough ERAM blocks are not available
EHI #2012404410 The ECU stops when calibrating a variable which is not
located at current "ETK Emulation Rages".
Note: Issue (with ETK D&T V3.4.2 and subsequent) is solved with
ETK D&T V3.6.0 (also part of INCA V7.0.0 SP9)
EHI #2012404415 Calibration outside the hard bounds is possible if the
defined range includes a singularity
EHI #2012404429 ProF: Flashing failed
EHI #2012404508 If an OpenEE-instrument locks INCA, all instruments
implemented by OpenEE are no longer served with data.
EHI #2012404560 Logviewer not available for Win7 64 Bit
EHI #2012404629 [WBID1789765672] INCA crashes when the calculated signal
gets "out of range"
EHI #2012404712 [WBID3717484010] while opening EE with option "Enable
Release Notes INCA V700 HF25.docx Seite 23 von 55
Calibration of Measurements: Yes".
WB if User Option "Experiment -> Calibration -> Enable Calibration of
Measurements: Yes".
Workaround: Enable Calibration of Measurements: No".
EHI #2012404724 Communication between INCA and ODX link is faulty
EHI #2012404729 Used display identifier [Display ID] does not show inactive
variables in EE
All active/inactive variables with the option [Used display identifier]
as [YES]/[NO] are now shown.
EHI #2012404751 A2L reading: Setting for special encoding will be overwritten.
EHI #2012404785 [WBID4293774349] Calibration Scenario Configuration: INCA
crash while reading scenario
EHI #2012404794 [WBID3202969049] INCA crash while loading an
ECU-Project(A2L+Hex)
EHI #2012404801 The 2D overlay editor in INCA 7.0 extended with zoom factors
New feature for INCA 7.1.0 backported to INCA 7.0.0
EHI #2012404810 [WBID347956746] WB on opening an experiment
Same WB like in the call 334777
EHI #2012404858 INCA hangs during XCPonCAN initialization
EHI #2012404867 Limited ERAM: If a block(e.g, 0x20000-0x30000) was not
emulated in the last session, it is not possible to calibrate a variable
on EE.
EHI #2012404869 Limited ERAM: If any component of MAP is write-protected,
"Ctrl+U" operation should not be possible.
EHI #2012404876 [WBID770727733] + [WBID1176513291] Walkbacks in EE when
working with Combined Editors
EHI #2012405020 Error message in MCD3 V2.2 when creating ASCII-file
(MCDWriteReadRecorder.Deaktivate)
EHI #2012405155 [WBID2097232047] WB when opening axis from CSV-file
EHI #2012405255 Flashing cannot be started because ProF detects an error
reading "convert" definition twice.
The second "convert" procedure leads to the termination of the flash
process. But the second definition of the "convert" procedure is an
allowed use case.
EHI #2012405439 MCD3: Measurement are displayed as "0" or invalid
measurements in case of remapping of rasters
EHI #323593 INCA-MCE: Configuration does not fill open rasters (INCA Part)
Note: Solution requires also an update to INCA-MCE V1.1.1 or subsequent.
EHI #323971 ES581: TimeOut of CCP commands for USB based devices wrong
EHI #324954 INCA - MCE Configuration fails if Japanese characters are in the
A2L long name
Release Notes INCA V700 HF25.docx Seite 24 von 55
EHI #328316 XCP on USB - New USBIO driver version V2.6 support
EHI #329663 [WBID414940203] Potential walkback when virtual calibration
measure device is created.
EHI #329886 ES720 Unknown Software exception
INCA part solved. Requires also an update of ES720.
EHI #329934 INCA MCE : A2L with Japanese character fail to proceed fast
ECU access.
Message display after selecting specific variables, which includes
Japanese character in long identifier of MEASUREMENT(or CALIBRATION).
Test bed computer could not find ES910.3 and is unable to proceed
fast ECU access.
EHI #335335 [WBID3730233174] + [WBID1676339687] when opening EE via DBB when
HWC is open in parallel
EHI #335369 ES720: ER LED on CCP hardware is set after power cycle connected
ECU multiple times. Solved in INCA. Requires an update of ES720 as well.
EHI #336201 It is not possible to assign a project with ETK-XETK AMP (OHI)
to a device (due to MMF error)
EHI #336587 [WBID2405776931] WB when open experiment after clear index
out of range warnings
EHI #336724 MCD3 V1.01: ES650 - device->Set Raster1 failed on LogicalLink
EHI #336726 VSD drops an 'System.ArgumentOutOfRangeException' when using
the 'already selcted' filter button
EHI #336754 SkipWriteProtectedBinaries does not allow to create link with
default binary
EHI #336923 Slew variable with BIT_MASK is not added properly to the
experiment
EHI #337059 [WBID2562174221] when open EE
EHI #337099 [WBID1454947006] when open EE using Virtual Prototyping Device
(X86 PC Controller)
EHI #337700 [WBID4129849108] when try to add special label to EE
EHI #337996 Timeout / error occurs if start of target server is delayed
e.g. due to heavy load on computer
EHI #339299 [WBID1222487598] WB reading project
EHI #340063 IPM locks up when reinitialize hardware after perform IT update
EHI #340720 [WBID847460348] When using Fill With Value in Overlay Mode
___________________________________________________________________
Release Notes INCA V700 HF25.docx Seite 25 von 55
INCA V7.0.0 HF14
Note: INCA V7.0.0 HF13 was not released at the ETAS Download Page
due to found side effect:
- EHI #2012404482 [WBID2390152117] WB opening EE in case of
EE with VUI and HWC changed
As of August 24, 2012, it is recommended to install (at the lowest)
the products/add-ons shipped with INCA V7.0.0 Service Pack V08:
For details read the corresponding release notes, please.
Please check the ETAS download center for updated versions.
Known issue
============================
Same like with INCA V7.0.0 HF13. Please read carefully.
Especially KIR PR 2012404415 (also published on the ETAS Download Center)
Bug fixes and improvements
============================
EHI #2012404482 [WBID2390152117] WB opening EE in case of
EE with VUI and HWC changed
Side effect introduced with INCA V7.0.0 HF13 solved.
EHI #2012404149 [WBID3932541479] WB on attempt to open experiment
EHI #336435 Possible to have widgets with unexpected names after
automatic inactivation from labels
___________________________________________________________________
INCA V7.0.0 HF13
As of July 19, 2012, it is recommended to install (at the lowest)
the products/add-ons shipped with INCA 7.0.0 Service Pack V07:
For details read the corresponding release notes, please.
Please check the ETAS download center for updated versions.
Known issue
============================
- ES581.3 ECU Flashing
Flash-issues with ES581.3 are not solved completely.
It is planned to solve the issue with the next version.
- EHI #2012404415 Calibration outside from hard bounds possible
if the defined range includes a singularity
KIR PR 2012404415 (published on the ETAS DL-center)
Release Notes INCA V700 HF25.docx Seite 26 von 55
If
within the A2L a COMPU_METHOD with a (possible) singularity (1) is defined
(e.g. f(x)=1/x)
AND
this COMPU_METHOD is used to calculate the hex value out of phy values
of a parameter
AND
the defined range (including boundaries) wrongly includes the singularity
of this COMPU_METHOD (here x=0; e.g. a range [0, 2000])
AND
the value (hex or phys) of the parameter is changed outside the defined
boundaries within the experimental environment of INCA (here: e.g. x=-20)
THEN
INCA does not detect, that the value of the parameter is outside
the boundaries and the value is wrongly transmitted to the ECU.
Note: (1)Singularity respectively pole of the function is a point at which a
given mathematical object (function) is not defined [e.g. division by zero];
infinity; f(x)=1/x at x=0)
Given: f(x)=A(x)/B(x)=(ax^2 + bx + c)/(dx^2 + ex + f);
f(x) has singularities, if B(x)=dx^2 + ex + f=0 (B(x) is zero).
The defined range (including boundaries) shall not include singularities
(e.g. in the example [1, 2000])
Affected INCA Versions: V6.2.1 and V7.0.0 (checked) and lower versions.
Workaround:
Change the A2L file so that the valid input range, including boundaries,
does NOT include a singularity(1) of the given function. As a result all
output values of the function and the boundaries can be calculated and
result is within a valid range of ECU (but not infinity).
(1) Singularity: see description.
It is planned to solve the issue with the next version.
Bug fixes and improvements
============================
EHI #312025 [WBID550393319] Walkback when read in csv file with wrong format
EHI #314344 Suppressing "View Elements" in EE not possible for measurements
in MCD3 use case
EHI #328391 ES581 - CCP: The progress bar in upload progress window shows more
than 100%.
EHI #329329 ES581.3 CCP upload fails due to "Inconsistent CCP command counter
received" error
EHI #330050 ES581 Performance XCP: Recording/visualization stopped after 10Sec
EHI #331416 MCD3 MCE Autoconfiguration - AlwaysUseFuli option is now supported
for MCD-3MC V1.0.1 und V2.2
EHI #331434 Search in online help locks up INCA if use non-default
installation
path. Note: Same like #2012403673
Release Notes INCA V700 HF25.docx Seite 27 von 55
EHI #331744 Some slew variables can no longer be displayed in a Measure Window
with INCA V7.0.0
EHI #332146 Data reduction delay does not work with pre start trigger time
configured
EHI #2011400409 Inactive variables get deleted from EE if the window contains
only inactiv variables
EHI #2012400847 HIL-System: INCA data logging - Window pops during automated
I/O-test
EHI #2012401221 ProF freezes while flash programming
EHI #2012401395 INCA stucks if initializing HW subsequent to a power fail on
the ECU
EHI #2012401397 Flashing only data with configuration not possible if
commands EXTENDED_MESSAGE and DISPLAY_MESSAGE in the [info] section
don't have return values.
EHI #2012401409 CCP connection break down using ES581.3
EHI #2012401603 No values for 2nd CAN using ES581.3 on different baud rates
EHI #2012401611 [WBID1885463622] when adding a new label to the EE
EHI #2012402132 Offset on CAN monitoring in dat file if 2 ES581.3 used
Same problem like call #2012401374. Solved with INCA 7HF11.
EHI #2012402163 Communication breakdown using USB Device on Panasonic CF5x
EHI #2012402305 ES580 Puffer goes full during stopped experiment
EHI #2012402379 Calibration of Mappings with several cells using ES581.3
leads to communication loss to ECU
EHI #2012402409 Flashing over ES581 not successful
EHI #2012402501 Add ECU project via COM-API is too slow
EHI #2012402761 Flash over ES581 fails with timeout while waiting for a
CAN-frame from ECU
EHI #2012402803 ES581 CAN - Performance: Delay in transmission
EHI #2012402913 [WBID2659564884] occurs repeatable during ASAP3 connection
when recording job is started
EHI #2012402980 [WBID2942607086] WB if closing ASAP2-Editor window before
content is visible
EHI #2012403084 Measure Calibrations are calculated from the RP if the
calibration page is switched automatically after init to the WP
EHI #2012403085 Adding project files via COM-API takes 10 times longer than
manual adding the project
EHI #2012403110 [WBID3472338849] System error during INCA session (part I)
Release Notes INCA V700 HF25.docx Seite 28 von 55
Workaround is to set the option #Strictly increasing#=No
Solved for one of the use cases which lead to this WB.
Solution for another use case is tracked with call #335271.
EHI #2012403164 Escape characters are not interpreted in INCA Monitor
EHI #2012403298 ASAM MCD 3MC Error #60217 with command SWITCHING
OFFLINE/ONLINE: Calibration can't be turned off
EHI #2012403314 [WBID3801010369] system error when working with OHI editor
EHI #2012403335 COM_API Error: If the name of the top folder contains a
special character it cannot be deleted
EHI #2012403370 [WBID1828090018] during long-lasting LCA tests
EHI #2012403454 The metadatas of the CDF file are lost during the association
of a CDF file with an A2L file
EHI #2012403529 COM-API: "SetDoublePhysValue(0)" returns false, although
calibration access was successful
EHI #2012403568 Log file "SystemInfo.log" is not aded to ZIP
EHI #2012403635 [WBID579070364] While open a HTML File in CDM a WB occurred
EHI #2012403662 Comment of the measurement file has "%H" in the time setting
instead of a value
EHI #2012403673 Inca crashes on online help search
Same like #331434
EHI #2012403684 [WBID1126647506] Initialize Experiment causes WB
EHI #2012403704 [WBID1126647506] Walkback during the experiment opening
EHI #2012403724 Connection loss to ES593_D CCP Driver
EHI #2012403731 There is no symbol showing characteristics dependency in CDM
EHI #2012403745 HSP: Targetserver failure during CCP session over ES593
Solved with HSP V9.7.0
EHI #2012403802 HSP: CCP values are missing over ES593
Solved with HSP V9.7.0
EHI #2012404096 [WBID6660969] if attempt to extend dependent variable view
in the ASAP2 editor
EHI #2012404207 Checksum calculation interrupts dyno cycle with Asap3/CCP
Note: Issue was already solved with HF11 (#2011409016)
EHI #332119 Serial number range for ES581.3 for recognition as ETAS device
extended
EHI #332586 No ETK index is available in HWC if ES1232 is used with
XAML ECU project
EHI #333604 Walkback when trying to delete an [undef] experiment from INCA
V7.1
Release Notes INCA V700 HF25.docx Seite 29 von 55
EHI #335346 ES720 Software exception due to invalid UTC time received from
the GPS mouse sporadically
EHI #331129 IP Manager: ES5xx device receive more than one IP address
resulting in disconnections
EHI #331384 ASAP3: Crash on SelectLookupTable after failed SelectDesAndBin
EHI #331455 [WBID784145778] when try to delete a INCA V7.1 experiment
EHI #335389 INCA 7 HF13beta2: Output-file after compare is empty
EHI #97244 Known Issue PR 253197 (#97244): System becomes very slow, if
running ES910 is disconnected
If an ES910 is disconnected during a running EIP experiment,
the INCA user interface becomes very slow.
EHI #101150 ASAP3-Recorder: GetRecorderResults returns error if recorder
file contains labels with CompuMethod "Verbal"
EHI #312004 IncaDataBase.ImportFromFile() fails if option "import in selected
folder" is active
EHI #327825 With the ASAM MCD3 MC v2.2 Testclient it is not possible to delete
the logical Link
EHI #330057 Copy and paste value into VTab Scalar does not work with
enumerations
EHI #330653 [WBID2797344315] LCO - integration test: An error window appears
during ECU measurement tests
EHI #331191 GPS hardware configuration issue with GPS workspaces - signals
listed twice
EHI #334311 [WBID753788609] during replace system in HWC
EHI #334629 MCD3 Test-Client opens the wrong INCA Version (V7.1.0)
EHI #334675 J2534 - TestBlocking System Exception at initialization HW
EHI #334884 ProF Flashing: Tgtsvr stops working on flashing WP->ECU
via UDS from KWP device. Side effect of #2012401221
___________________________________________________________________
INCA V7.0.0 HF12
Known issue
============================
No new issues.
Bug fixes and improvements
============================
Known issue of HF11 solved:
EHI #332207 Delay in start measurement of CAN Values
Release Notes INCA V700 HF25.docx Seite 30 von 55
___________________________________________________________________
INCA V7.0.0 HF11
Known issue
============================
See HF12: EHI #332207 Delay in start measurement of CAN Values
Therefore HF11 was never published on the ETAS download page.
Bug fixes and improvements
============================
EHI #94408 ASAM MCD 3MC Editor: Problems with help menu
EHI #99128 Variables are selectable, even if the performance calculation
disables these variables
EHI #100263 J2534 ES581: Baudrate 1MBaud initialized but not supported
EHI #2011405072 LAB file not usable
EHI #2011405074 Write out of LAB File ignores entry .Output
EHI #2011407108 Asynchronization in the ASAP3 communication.
EHI #2011407945 [WBID902711056] System error while repairing the database.
EHI #2011408030 The IP Manager pops up at corporate network connection
and asks for reconfiguration
EHI #2011408422 Logical signals are not correctly interpreted and displayed
in the experimentation
EHI #2011408717 Experiment does not work on ES720 due to high RAM usage
EHI #2011408981 No information about lost ES581 device with CAN-Monitoring.
EHI #2011409016 Adjustment of checksum interrupts test bench cycle
EHI #2012400248 Downloadig data to the WP fails with an ES581.3/CCP device
EHI #2012401091 Experiment require too much RAM for ES720
EHI #2012401374 Timeshift in the Recording if two ES581.3 used in the
HW configuration
EHI #2012401376 Inconsistent CCP command counter
EHI #2012401382 PC hung up during INCA session using ES59x devices.
EHI #2012401385 EIP 7.0.2 [WBID2700811984] (ExCPMStackOverflow) A stack
overflow has occurred.
EHI #2012401394 The warning "DAQ_MODE_ALTERNATING" occures instantly in
the experiment. INCA V6 showed the information only once.
Release Notes INCA V700 HF25.docx Seite 31 von 55
EHI #2012401408 While work with Database repair Win XP generate
a error message.
EHI #2012401491 [WBID1727672009] due to wrong CAN DB definition files
Solution: Prevent reading CAN DB files with wrong definitions.
EHI #2012401568 [WBID4190502864] occurs sporadically when a label was
inserted to the experiment
EHI #2012401613 Read ECU ID fails if ECU sends the ASCII character % (0x25)
EHI #2012401868 Japanese description in the Path Selection dialog
(ProF installation) is garbled
EHI #2012401908 [WBID2380438454] System Error performing HPT with reimport
EHI #2012401910 Incomplete IPMD file of ES581.3 is not being validated
on ES720 due to missing CAN monitoring
EHI #2012402165 INCA-FlexRay: INCA can't read FIBEX V3 file
Note: Update to INCA-FlexRay V7.0.3 required.
EHI #2012402412 [WBID247455946] Exception is not resumable
EHI #2012402628 CCP download is not Optimized
EHI #2012402751 [WBID2780797359] and [WBID793658695] during long-lasting
LCA tests
EHI #2012402806 EW_I700: [WBID2700811984] when assigning INTECRIO project
to ES910
EHI #2012402817 Error message when analysing the database
EHI #2012402820 [WBID852245266] INCA Crash when adding Etarget project
EHI #2012402895 Upload with ES581.3 (CCP) is not possible - Inconsistent
CCP command counter received
EHI #311692 [WBID138734720] Walkback on MCD3 look:
EHI #326037 [WBID4129289469] (ExCPMStackOverflow) A stack overflow has
occurred.
EHI #328178 XETK: Incorrect display of serial number of XETK in HWC
EHI #328286 Monitor message for experiments with new INCA V7.1 oscilloscope
in older INCA versions
EHI #328290 Hotfix to prevent import of *.ee files with new
INCA 7.1 oscilloscope into INCA V6.2.1 and V7.0
EHI #328297 Getting Unexpected Error Message when Copy and Paste
VTab Value with Data Representation = "Hex" and Conversion Method
has a Default Value and label is used in Combined Editor
EHI #328557 [WBID3892241955] Walkback encountered when reading in hex file
EHI #328821 No filter for slewable variables in VSD
Release Notes INCA V700 HF25.docx Seite 32 von 55
EHI #328858 INCA does not allow calibration of all values when all
calibration handles are used
EHI #329086 Getting Unhandled Exception when try to select
Measure Array / Matrix in VSD
EHI #329098 ASAP3: [MemoryAccessError]: Command Get Recorderresult Header
-> ASAM MCD 3MC 4 INCA -> Memory Access Error
EHI #329384 Project files take a long time to load
EHI #329416 CAN, CCP Switch off / on ECU has at least no measurement
EHI #329846 Backport of INCA 7.1.0 OCD ES581 solution for INCA 7.0
EHI #329909 ASAP3: Command "Get Recorder Results" returns "Invalid
Measurement"
with temp ASAP3.dat
EHI #329910 ASAP3:Command "Define Recorder Parameter" failed if the wrong
Datatype is used for the registrievalue "UseRasterCheckForMeasurement"
EHI #329912 ASAP3_: Unknown Error ASAP3.exe at Command "PARAMETER fOR
VALUE ACQUISITION"
EHI #331002 INCA-EIP (INCA 7.0.0 part) Performance: There is first a
"Verify WP and RP", than a FW check, and than again a "Verify WP and RP"
Performance improvement for the upcoming INCA-EIP 7.0.3
Note: INCA-EIP 7.0.3 is requied.
____________________________________________________________________________
INCA V7.0.0 HF10
Known issue
============================
See KIR issue solved
Bug fixes and improvements
============================
KIR issue solved:
EHI #2012401578 Differences in CDM not detected if data exchange files are
used for compare
If
INCA CDM is used for compare
AND
two data exchange files are used for compare
AND
the CDM "Compare" option "Use Precision for Compare" is set to "for data
exchange files only"
AND
the INCA "User Option" "Data exchange" "Maximum precision" is set to "from
ASAM-2MC file"
AND
Release Notes INCA V700 HF25.docx Seite 33 von 55
the CDM "Compare" option "Compare Mode" is set to "tolerant" OR "tolerant bi-
directional"
AND
Parameter of type VAlBlk is used
AND
No other type of parameter is compared before compare of a parameter of type
VAlBlk
AND
Both parameters are >= 1
AND
the difference between the parameters is smaller than 50%
THEN
there is no difference detected (wrong behavior)
Note: Independent of the issue: Compare of address values should not be done
in tolerant mode (but "exact").
Affected INCA Versions: INCA V6.2.1 and INCA V7.0.0
Solved with INCA V6.2.1HF31 and INCA V7.0.0HF10
EHI #100970 Number of Repetitions is not written to Comments anymore
EHI #312023 MIP not working with IncaGetRecords command
EHI #323990 [WBID1588301702] Switching projects causes walkback when
opening experiment
EHI #326130 MCE configuration is carried over to new experiments
EHI #326801 ASCET model in INCA-EIP causes ethernet disconnection error
EHI #327012 Repeated "FullScan" parsing of INCA data base via MCD 3 leads
to lack of accessable memory
EHI #327012 "Deliver Project" via EE adds additional entry in A2L file
EHI #327145 [WBID4249392081] when deleting an ASAP2 project
EHI #327693 Rescale Axis issue with Reset to "Reset to Reference Page Value
/ Complete Map"
EHI #327727 [WBID2886875596] when switching CDM compare option in CDM and
label of type VALBlk is calibrated in label editor
EHI #327750 After renaming Trigger Channel of ES1303 the Trigger is removed
from the Experiment
EHI #327805 [WBID4229974805] in CDM occures when file is linked to
ASAP2 project in CDM
EHI #328053 [WBID849430863] when dataset is removed from CDM source
EHI #328529 The connect to ASAP file feature does not transfer the variable
type attribute
EHI #2011402222 [WBID1890870391] when using "Freeze working Dataset" command
in Experiment Environment
EHI #2011403940 Measurement window changes background colour
Release Notes INCA V700 HF25.docx Seite 34 von 55
EHI #2011404284 DB is growing working with same workspace
EHI #2011407670 Boolean labels can not be used with INCA-MCE
EHI #2011407754 [WBID94158247] System Error during recording
EHI #2011408016 Problem of communicaton with XCP on Ethernet using
VECTOR vx1110 device
EHI #2011408018 Not possible to add a2l in INCA 7.0
EHI #2011408777 Repeated moving action of variables in a table editor
window parameters leads to corrupt window content
EHI #2012400748 Address extension in CCP SET_MTA is not sent correctly
if ES59x is used
EHI #2012400909 [WBID1588301702] System error when opening EE
EHI #2012401344 Gaps in measurement with ES595
EHI #2012401411 Recorder values are incorrect
EHI #2012401612 Failed to start ECU documentation with Acrobat X
- supported with HF9ff
EHI #2012402203 Dependent parameter calculation results in a false value
____________________________________________________________________________
INCA V7.0.0 HF9
Known issue
============================
Known issue with ES9xx Add-on V7.0.3 and INCA-EIP V7.0.1
of INCA 7.0.0 SP1 is solved with INCA 7.0.0 SP2 and following.
New features
============================
EHI #2012400694 ECU Docu Interface: Support of Acrobat X
Bug fixes and improvements
============================
KIR issue solved:
EHI #2012400625 CAN Monitoring measure values might be not visible and
not recorded
If
INCA 6.2.1HF15 to 7.0.0HF8 is used OR
the corresponding ES7xx versions (ES715v6.2.1/SP5; ES720v7.0 all versions)
AND
CAN-monitoring measurement/recording is executed
AND
HW is running longer than 71.3Min
AND
Measurement is stopped (via "Stop Measuring (F9)") for a period of longer
Release Notes INCA V700 HF25.docx Seite 35 von 55
than 71.3Min (Recording "Pause" is not affected)
AND
Measurement is restarted again
THEN
CAN-monitor measurement is stopped / halted without any further information
(no warning, no error message etc.).
--> Experimental Environment: no further update are made
(always the same value displayed);
Not applicable for ES7xx
--> Recording: measurements are no longer written into file.
Note: There is no defect if the measurement is not stopped.
KIR issue already solved with INCA 7HF8:
EHI #2011407162 CAN-Monitoring: Buffer full error displayed by mistake
If
INCA 7.0.HF4 to HF 7 is used
AND
HW integrated via BOA is used: ES520, ES580, ES511, ES910, ES921, ES592,
ES593, ES595, Vector CANcardX, CANcardXL, CANcardXLe, CANcaseXL and VN7600
(not affected: ES715, ES581.x, ES590, ES690, ES1222)
AND
measurement is executed via CAN
AND
high bus load, slow computer, experiment with high number of measurement
items,
THEN
an error indicating that the "buffer is full" and that the measurement
should be aborted, may be erroneously displayed
Note:
- User is informed (via error message) that buffer is full and that
the measurement should be aborted. But, measurement and error handling
in the case of a real buffer overflow is not affected.
- Solved with INCA 7HF8. But displayed buffer filling level is still
only a rough indication.
KIR Issue finally solved:
EHI #2011402280 Working point is saved wrongly in the measure file
- and working point display
Display working point also with affected projects on demand
EHI #2011405167 [WBID754229532] with array's solved
EHI #2011405395 [WBID1841638718] Importing attached file with the option:
Import into selected folder
EHI #2011405655 Measure file from ASCET V5.2.2 is wrongly interpreted
Release Notes INCA V700 HF25.docx Seite 36 von 55
EHI #2011405773 Two ES1303, each in a different ES1000, not usable
EHI #2011407162 CAN-Monitoring: Buffer full error displayed by mistake
EHI #2011407636 The Description information to a measurement signal in
measurement files is not available
EHI #2011407755 [WBID2746652332] while inserting new variabnle in the EE
EHI #2011408059 A large measurement file, recorded with INCA V7.0.0 and with
empty data groups, can not be used with MDA V7.0.0.
EHI #2011408066 Disturbing output in control flow monitor
EHI #2011408223 [WBID3465117962] when exchanging the axes
EHI #2011408254 ASCII-Files cannot be used in MDA
EHI #2011408758 [WBID1268797178] if attempt to start EE
EHI #2011408778 [WBID4182064724] after ToolAPI command GetScenarioNames
EHI #2011408813 Package information from Log-files and "Loaded packages"
does not correspond to each other
EHI #2011408977 CDM QM-Basic entries are lost when XML file is removed
from "Destination"
EHI #2012400105 A2L generator loses ETK version and type
EHI #2012400310 [WBID579070364] in CDM if preview of MAP or table started
with STRG+W
EHI #2012400416 Not possible to establish ASAM3MC3 session with MCE -
Ethercat labels
EHI #2012400694 ECU Docu Interface does not work with certain path name
(...\xxxx.pdf\...) and support of Acrobat X
EHI #2012400972 "Error" message in INCA-EE
EHI #2012400979 Read checksum from .chk file does not work while flashing ECU
EHI #2012401117 After ETK hardware initialization an automatic download
occurs without popping up of the memory page window
EHI #311184 INCA Crash During Morphee "Full Scan"
EHI #311805 [WBID2635661307] during database access
EHI #311808 [WBID776998434] EtasGenericHWItemSystemVersion3 does not
understand checkVerification
EHI #323807 Wrong result for XCPX_UNLOCK Command in PROF
EHI #323896 No connection to ETAS hardware with Win7 if initialize before
connect hardware
EHI #323914 No blockmode flashing with XCP possible if the ECU doesn`t
Release Notes INCA V700 HF25.docx Seite 37 von 55
support blockmode UP/DOWNLOAD
EHI #324324 Recording appears to update periodically instead of constantly
with oscilloscope in configuration
EHI #324987 [WBID2879276672] after reading data exchange file via EE
datasets read calibrations from file
EHI #325868 INCA - ALIGNMENT for RESERVED in RecordLayout
EHI #326406 Exception in ASAM MCD 3MC 4 INCA 2 Module when connecting to
INCA by the MCD3 Client
EHI #326407 Logical Links for FULI will not be listed if optimization options
are set ( PROD77119 & PROD82279)
EHI #326539 [WBID3508097936] after compare to ASCII in CDM
EHI #326727 [WBID467667205] when open old Display Configuration
EHI #326729 CDM shows error icon on all labels when DCM file linked to
ASAP2 Project
EHI #326745 TgtSvr leaking memory at HW-Init
EHI #326858 ES581 CAN Monitoring timestamps are not correct
____________________________________________________________________________
INCA V7.0.0 HF8
Known issue
============================
The ES9xx Add-on V7.0.3 has to be installed after the INCA-EIP V7.0.1
installation to achieve correct functionality for the complete chain.
(This is automatically respected if updated via Setup_ServicePack.)
The upcoming INCA-EIP V7.0.2 solves this issue.
New features
============================
EHI #2011400945 INCA support of CAN extended with 50.000, 666.666, 800.000
Baud
INCA support of CAN was extended with 50.000, 666.666, 800.000 Baud rates
for the following hardware.
Hardware - Required Product/AddOn
----------------------------------
ES511 ES5xx AddOn V7.0.2
ES592 ES5xx AddOn V7.0.2
ES593 ES5xx AddOn V7.0.2
ES595 ES5xx AddOn V7.0.2
ES910.2/.3 ES9xx AddOn V7.0.3
ES921 ES9xx AddOn V7.0.3
ES580 INCA V7.0.0 HF8
ES581.2/.3 INCA V7.0.0 HF8
ES520 INCA V7.0.0 HF8
Release Notes INCA V700 HF25.docx Seite 38 von 55
This requires an update of the corresponding INCA products/add-ons
contained in INCA 7.0.0 Service Pack 01
EHI #325761 Support Service Packs - Setup Service Pack
to install the INCA HF and the recommended INCA Add-Ons
A service pack (SP) is one single ZIP file containing
- Latest INCA hotfix
- Latest version of related Add-ons
- Installation routine, which automatically installs the hotfix
and updates the add-ons installed on the users PC
For more details see INCA Introduction of Service Pack (SP).pdf
shipped together with the first SP
Bug fixes and improvements
============================
- KIR Issue solved
EHI #2011402280 Working point is saved wrongly in the measure file.
EHI #100866 [WBID3465117962] WB solved
EHI #100869 [WBID1858677281] Several WBs with same ID solved
EHI #101087 [WBID3862466148] WB solved
EHI #101290 ES581: ECU connection lost after stop Measurement using
two ES581 on the same time
EHI #1004566 [WBID667152105] Walkback when perform CDM copy with Copy curves
and maps set to Expand
EHI #1004568 ES581 communication drops out during measurements
EHI #2011400945 INCA support of CAN extended with 50.000, 666.666, 800.000
Baud
EHI #2011402280 KIR Issue solved: Working point is saved wrongly in the
measure file.
EHI #2011403190 XCP-issue if a CAN-monitoring is in use
EHI #2011404115 Misleading warning after raster mapping
EHI #2011404483 Checksum calculation with ES581.3 during every start-stop
of Experiment
EHI #2011404544 Inconsistent behaviour with equal measurement names
EHI #2011404726 INCA re-initializes ECU connection after measurement stop
EHI #2011404853 Bit is wrongly displayed in yt-ocilloscope
EHI #2011406256 Walkback while reading cdfx file generated by EESY
Release Notes INCA V700 HF25.docx Seite 39 von 55
EHI #2011406408 CDM- Action-List shows a names of parameters in wrong
sequence.
EHI #2011406855 Identical conversions get listed as differences
EHI #2011406955 Type and version information of ETK_MAILBOX as defined by
ASAP2 are missing after regenerating A2L
EHI #2011407121 INCA 7 generates faulty MDF4 files
EHI #2011407159 [WBID628375818] INCA crashes after comparing in CDM
EHI #2011407162 ES580 buffer goes full during CAN-Monitoring
EHI #2011407253 Value matrix nx1 not identified as valueblock
EHI #2011408065 Background color of measure table changes
EHI #2011408149 Not possible to start recording with attached EE if using an
XETK aml for an ETKT2
EHI #2011408223 [WBID3465117962] WB solved.
EHI #2011408421 Missing functionality for sorting parameter by function in CDM
EHI #99185 Calls 92278, 95153 and 92768 solved
EHI #311798 [WBID3244425468] WB solved
EHI #312531 Wrong DAQ assigned after multiple reconfiguration
EHI #322966 ES581 not works with CCP,UDS,KWP and XCP
EHI #322969 [WBID3401309891] WB solved
EHI #323258 CAN_MON first timestamps at CAN Monitoring are incorrect
EHI #323302 ES581 CAN Monitoring via CAN1 and 2 with different baud rate has
at start measurement no correct values
EHI #323313 Timestamp Jumps on DaisyChain Devices connected on ES592
EHI #323339 ES581 CAN1 Monitoring has negative timestamps if CAN2 is used
with KWP
EHI #323374 Multiselect with Shift an Scroll in Display Configuration
EHI #323388 ES581 CAN Monitoring Port disconnected during reinit HW
EHI #323413 Wrong description in CDM online help
EHI #323606 Backport Full Scan related Filter Options (PROD77119 & PROD82279)
EHI #323932 No XCP Flashing possible if Init fails in INCA
EHI #323973 Initialize CAN-Monitoring during start experiment fails
EHI #323977 Possible that label with different values are shown as grouped
EHI #324036 INCA-MCE V1.1: Support upload axis points
Release Notes INCA V700 HF25.docx Seite 40 von 55
EHI #324361 ES581 Multi Client Backport: Second client terminates
INCA communication
EHI #324406 ES581 Multi Client Backport: INCA display no error message
on access the Port as second client with other settings
EHI #324416 INCA-MCE UploadAxisPoints: Number of axis points can be changed
via API
EHI #324554 Help for 3rdParty Hardware for INCA V7.0 updated
EHI #324587 ImportExportHexFiles: ECU project not read in correctly any more
EHI #324641 ES910.3, ES921: Lost of communication during measurement XCP
EHI #324675 New Baud rates with ES520: Init XCP with 50 kBaud shows
access violation
EHI #324691 KWP2000 on CAN implementation for RENAULT NISSAN
EHI #324829 [WBID144291448] WB when try to change multi selected
Output Values in Combined Editor via F2
EHI #324846 [WBID1449895592] WB after List Action
EHI #324847 [WBID1511931280] WB when opening CDM config
EHI #324860 New Baud rates 800K CCP: New Commando for CCP does not work
EHI #324935 CDM: List to CDFX incorrect - empty <LABEL> entry for axis
EHI #324937 CDM: List to CSV files shows errors - additional entries for
MIXEDAXIS '<name>/y ' in CSV file
EHI #324962 Error in selecting MCE labels via MCD3
EHI #325732 Hotline Contact Information Outdated (UK updated)
EHI #325761 Support Service Packs - Setup Service Pack
____________________________________________________________________________
INCA V7.0.0 HF7
Bug fixes and improvements
============================
Side effects introduced with HF6 solved:
EHI #2011407709 INCA-EE: The "dif" counter and ECU-state are not visible
with ETK-s projects with EMU-RAM
Side effect of HF6 solved.
Affected are ETK-s - projects with EMU-RAM.
AND
the user-setting "operation mode" = "Experiment preparation" only
Note: Not affected, are projects with ETK-p
EHI #323871 ES720 - Inactivated recording after open specific EE via COM API
(ES720 RecordingJob)
Same like #323973. Side effect of HF6 solved.
Release Notes INCA V700 HF25.docx Seite 41 von 55
EHI #323973 INCA700HF6 Initialize CAN-Monitoring during start experiment fails
Same like #323871. Side effect of HF6 solved.
EHI #324034 Init device in HWC resets the baudrate to default settings
Issue found with #323973
Baudrate correction for INCA V5.4.1 exports, introduced with HF6, removed.
Baud rate has to set manually.
____________________________________________________________________________
INCA V7.0.0 HF6
Addendum Nov 15, 2011:
=============================
Due to side effects EHI #2011407709 (Details see section HF7) and #323871
INCA V7.0.0 HF6 was not released.
The content of HF6 is completely integrated into HF7.
New features
============================
EHI #310969 New feature: "ASAP3 - Automatic configuration with MCE virtual
device if available"
Support of the updated INCA AddOn for which INCA V7.0.0HF6 is a
minimum requirement:
EHI #311406 INCA-EIP V7.0.1 support by INCA V7.0.0
Bug fixes and improvements
============================
EHI #309630 Reconnect on MCD3 Interface fails if special history is
precondition
EHI #310933 ES720HF2RC01 - TargetServer Virtual Memory increases significantly
EHI #311211 J2534 does not transmit data using Windows 7 OS
EHI #311549 INCA-MCE HW Configuration looses INCA-MCE Link
EHI #311705 CCP Upload fails when using ES581.3
EHI #311747 [WBID862924121] WB occurs at INIT of MCD3V2.2
EHI #1004280 INCA using a very large amount of memory with hybrid
EHI #1004552 Variables moved to different rasters when open export on PC
without ES715 AddOn installed
EHI #1004565 ES720 Stops recording but measure light is blinking and
Configurator shows unit in trigger wait mode
EHI #1004580 Recording stops when add a calibration variable to the experiment
with trigger enabled
Release Notes INCA V700 HF25.docx Seite 42 von 55
EHI #2010406231 "Context menu (via right-mouse click) is lost in case of
huge Experiment Environment
In a complex Experiment (many layouts, many variables, nearly all the rasters
are full) usage of Context menu is via right mouse click no longer possible."
EHI #2011402301 Properties of the measurement window do partially not exist
EHI #2011402629 Column width changes
EHI #2011402940 Separator function with more than one letter not working
correctly
EHI #2011402996 Wrong time stamp for dataset in database browser
EHI #2011403719 System Error in CDM during Copy action via API
EHI #2011403767 [WBID742315697] WB in CDM when copying Quboid maps from a
CDFX file to current data set with active monotony check with verbal
translation of axes
EHI #2011403877 Fewer labels can be measured with ES910.3 then with ES590
or ES1000 System over ETK.
EHI #2011403904 ES581/3 with 2. CANs. It is not possible to use IPETRONIK-HW
EHI #2011404203 [WBID973124537] if a DCM file is removed from CDM
EHI #2011404306 Unnecessary error during copy action
EHI #2011404326 CDM: Copy takes significantly longer than with older version
EHI #2011404402 [WBID610301759] WB if attempt to read CDFx file
EHI #2011404526 ES581.3 loses Messages on CAN while flashing on UDS
EHI #2011404820 [WBID4184384051] WB creating a Hex file
EHI #2011405030 Measurement filename index gets lost if changing principal
part of the filename
EHI #2011405120 [WBID3235928131] WB using IPETRONIK AddOn in INCA
EHI #2011405262 Compare action shows wrongly a difference
EHI #2011405437 [WBID2252893887] WB using experiment with IPETRONIK AddOn
EHI #2011405714 [WBID3235928131] WB using CSM AddOn in INCA
EHI #2011405947 Dependent parameter calculation not performed after correcting
the reason for the dep. param error. A not consistent dataset results
EHI#2011406584, EHI#2011406030, and EHI#2011406126 Measurement variables of
a matrix type are wrongly selected by COM-API interface
EHI #2011406338 A2L parser generates failures while reading and marking
multiple defined labels
EHI #2011406584 Measurement variables of a matrix type are wrongly selected
by COM-API interface
Release Notes INCA V700 HF25.docx Seite 43 von 55
EHI #96965 User unable to connect to hardware even though IP-Manger found
hardware
EHI #98376 "Solved PR 279233 (98376): Wrong time stamps for recording of
calibrations in virtual prototyping
Recording of CHARATERISTICs in virtual prototyping experiments resulted in
wrong time stamps for these CHARACTERISTICs. This problem is now fixed in
combination with INCA V7.0.0 HF 6 and INTECRIO V4.0.0.
This means that executable virtual prototypes need to be generated with
INTECRIO V4.0.0 (or later) again and INCA V7.0.0 HF 6 needs to be installed
as well."
EHI #98656 Wrong default status of Ipetronik Subdevices
EHI #99035 Enlarge the default blocksize for checksum calculation in INCA
for UDS and KWP2000
EHI #99155 CANMon baudrate reset when importing Export file from INCA 5.4.1
EHI #99984 Can Monitoring with 800K Baud with ES581
EHI #100110 XCP reconnection and ES720
EHI #100237 CCP Optimized download is not available if checksum qualifier
starting with 0xC is used
EHI #100560 PDF Printer does not respect the changed settings in the INI file
EHI #100616 ECU Flash using INCA7 and ES581.3 via CCP/ProF fails.
EHI #100642 InstCheck.log in INCA I700 missing
EHI #100865 [WBID112422306] Etarget: SGDataItem does not understand
isAbsWorkBaseData
EHI #100981 Raster filling with ES592 works not correct
EHI #101024 [WBID3528471361] WB when opening an experiment with given
a2l-file including compu method IDENTICAL
EHI #101099 INCA needs up to 4 minutes to close Experiment with ES780 and
Calculated Signals (solved with ES780 AddOn V7.0.3)
EHI #101293 OpenEE: Changing Device and Channel name renders
"Scalar Measurement Instrument" invalid
EHI #311109 Possible to get different entries in a Protocol Of Configuration
dependent on the former action
EHI #311140 Simultaneous call from two threads to
OCI_CreateCANController() fails
EHI #311150 ConnectToModule not allowed if already connected.
EHI #311151 Memory Access Violation during HW-Init
EHI #311204 Internal error in API for MCD3 server at switch calibration
access off (when no HW Connected)
Release Notes INCA V700 HF25.docx Seite 44 von 55
EHI #311368 ASAM MCD3 V2.2 MultiClient: Locking/Unlocking IMCSystem by
second client leads to not correctly unlocked objects
EHI #311483 ES581 wrong command and command counter after command return
code 0x35
EHI #311781 HotKey Shift+F10 does not work in VSD
EHI #311845 System error if ES3xx device will be added to HWC
EHI #311865 CDM: Unexpected WRN lab file found "BOOLEAN.FW_wU8 ;
Hard Limits Exceeded" at copy action.
EHI #312058 Calibration windows stay gray in MCD3-MCE use case even if module
connected and download happened.
EHI #312268 LoggingUninstall.exe does not uninstall correctly
EHI #312297 EIP [WBID30764971] WB appears when Calibrating ETarget Values in
EE
EHI #312308 INCA does not react any more when Adding Calibration Variable via
MCD3 in specific environment
EHI #323181 BOA framework occasionally closes someone else's socket handle
EHI #323185 The QNX BOA framework allows some threads to remain in a "dead"
state instead of terminating cleanly
EHI #323405 [WBID172005526] EtasAbtShellView does not understand bringToFront
EHI #323579 INCA crash during test bench "Full Scan"
EHI #1004572 WB when apply new recording job and start recording
EHI #2011401648 CCP-communication with DQ-500-SG is not possible
____________________________________________________________________________
INCA V7.0.0 HF5
EHI #2011405922 INCA V700HF4 Recording function in the Experiment Environment
is no more working in case of large verbal conversions
EHI #2011406232 INCA 7 Installation of C++ redistributable shows error
message about incorrect installation
EHI #311566 Unable to read measure file if
1)master channel is Not 32 or 64 bit integer
2)virtual master channel is used.
EHI #311698 INCA 7 HF Installation - remove screen and button "start INCA HF"
after successful installation
EHI #312136 INCA-SIP cannot load MDF3 file. MDF IP crashes with access
violation
____________________________________________________________________________
Release Notes INCA V700 HF25.docx Seite 45 von 55
INCA V7.0.0 HF4
New features
============================
Support of the following new INCA Addons
for which INCA V7.0.0HF4 is min. requirement:
- INCA Addon MCE V1.0.0
- INCA Addon SIP V7.0.1
- INCA AddOn ES9xx V7.0.1
- INCA AddOn LIN v7.0.1
- INCA AddOn FlexRay 7.0.1
- INCA Addon QMBasic V7.0.0HF1
- INCA Addon eCDM V1.0.0HF1
Bug fixes and improvements
============================
EHI #1004548 [WBID780406887] - Walkback when switch experiments in EE
EHI #1004551 ES511 - Error when change baud rate of CAN port with 2 ES511s
in configuration
EHI #1004569 [WBID538613362] - Walkback when change Output Voltage settings
on ES611
EHI #1004574 PC running out of system resources when open and close experiment
several times with script
EHI #2010400679 "Deleting Hardware setup when performing ""replace system""
in Hardware editor
(solves also calls 98237 and 98654)"
EHI #2011402247 The measure comment is truncated
EHI #2011402643 Entry in Variable Configuration is not refreshed
EHI #2011403022 WBID780406997 System Error when switching experiment
EHI #2011403176 [WBID2524212407] Walkback beim Starten des Experiments
EHI #2011403257 Borders are worngly computed
EHI #2011403768 ES910/592/921/INCA 7.0.0/1/OHI - It is not possible to find
the CSM devices
EHI #2011403899 Bit display on same address
EHI #2011403919 Copy using mode expand does not work correctly
EHI #2011404055 "Experiment Tag not available" Error message when trying to
save to file the adaptive characteristic
EHI #2011404059 CDM: Detected differences not listed into the output file
EHI #2011404102 WBID320118438 Walkback when writing Convert Experiment
Writing Template
Release Notes INCA V700 HF25.docx Seite 46 von 55
EHI #2011404113 CCP connection is lost during measurement
EHI #2011404277 NCA start on VBS script runs through with positive result,
although DB is courrupt
EHI #96883 INCA-MCE10: Deleted Cali labels are still selected in INCA and
part of LAB-File
EHI #97152 eCDM V1.0.1: Wrong File ID send from Files in destination of
CDM when they were retrived from eCDM
EHI #97253 eCDM V1.0.1: Files can not be updated in CDM from multiple
ExchangeFile
EHI #98223 [WBID4057591415] UndefinedObject does not understand putValueIn:
when writing an ASAP2 file
EHI #98355 Unexpected sequence of hardware initialization
EHI #98545 [WBID3113191819] UndefinedObject does not understand notEmpty
EHI #98576 [WBID2255254694] RBMeasureDataDisplayConfig does not understand
associationsDo:
EHI #98582 OpenEE: Customer Instruments in EE not useable after moving v
ariable to other instrument
EHI #98606 Improve performanve with MCD3
EHI #98877 Walkbacks caused by MCE backanimation
EHI #98905 Deleting Hardware setup when performing "replace system" in
Hardware editor
EHI #98911 [WBID1888589593] receiver must be a boolean
EHI #99103 CAN DBC to ASAP2 Converter problems
EHI #99150 ES930: Configuration of output channels fails in case of grouped
channels (rate)
EHI #99319 Backanimation of several labels that belong to the same ECU address
does not work correctly
EHI #99755 INCA-MCE10_Calibration: [WBID3545445305] On Curve calibration
EHI #99776 NCA-MCE10_MemoryLeak: INCA crash by opening EE multiple times
via MCD3 in automatic tests
EHI #99977 Exception in VSD when adding variables to VUI
EHI #99978 INCA-MCE10 CalibrationBackanimation: Rundown still visible with
1st update rate + WB on Exit: [WBID320600124] UndefinedObject does not
understand dataObject
EHI #99984 Can Monitoring doesn`t work with 800kBaud with ES581
EHI #100133 INCA-MCE Using a FORMULA CompuMethod leads to error on
measurement start with MCE
Release Notes INCA V700 HF25.docx Seite 47 von 55
EHI #100200 ES7xx: TargetServer abnormally exited on starting experiment
EHI #100226 INCA-MCE10 [WBID1529621036] on selection the second LogicalLink
via MCD3V2 - EtasFixedSizeMoveableEmuRAMWrapper does not understand
hardwareInterfaceManager
EHI #100276 [WBID320600124] UndefinedObject does not understand identifier
EHI #100346 OpenEE: Removing Variable from Array Calibration Instrument via
context menu renders instruments invalid the next time you open the EE
EHI #100373 The time quality is not set properly for MDF 3.3 and MDF 4.0
EHI #100409 INCA 7.0: Measure Array elements can not be added to OpenEE
instruments
EHI #100452 Walkback if map is calibrated via iLinkRT
EHI #100479 Wrong timestamps on ETK and ES610 when measurement starts
4000 seconds after switching HW on
EHI #100590 Support of eCDM V1.0.1
EHI #100647 Additional bytes in CC block in MDF V4 files
EHI #100649 Setting / Getting of StartTime/Time offset & DST does not behave
identically across plug-ins
EHI #100722 INCA-MCE10_CompuMethods: FORM "X" results in wrong values via MCE
EHI #100770 [WBID1912520931] Copy/Paste of EIP project causes walkback
EHI #100826 EE: [WBID1037419145] when change Measure Window Display Type to
Gauge via Display Configuration Tab from the VSD
EHI #100860 Automatic snapshot does not work correctly if a recording time
is specified
EHI #100871 [WBID1487019803] Primitive failed in: SmallInteger>>#rem: due to
Divide by zero in argument 1
EHI #101010 EW_I700/1_TX_EE - Walkback [WBID1193338098] while opening
ODX Experiment'
EHI #101033 Walkback after intiliazation of INCA at test bench via MCD3 V2.2
EHI #101044 Update to BOA v1.4.0 latest version
EHI #101059 EW_I700HF4<_TI_ASAMMCD3MCV22_CompuMethods: An IMCDbMeasurement
with "FORMULA" CompuMethod has null as RefDbCompuMethod thus probably
always 0.0 as measurement value
EHI #101086 Replace AS951 with ES910 does not work with attached Workspace
EHI #101105 INCA-MCE10 Start of measurement in Tool API must be synchronous
EHI #101120 CDM: Softlimits are not listed for Label / listed incorrectly
EHI #101142 [WBID1871692419] UndefinedObject does not understand status
Release Notes INCA V700 HF25.docx Seite 48 von 55
EHI #101152 EE: Remaining recording time not shown in Experiment Environment
anymore with HF1 and higher
EHI #101157 No clear message, if database size limit is exceeded
EHI #101173 Additional bytes in CC block in MDF V3
EHI #101185 DaisyChain: SFHSystemES400.dll delivered by
AddOn ES4xx/ES6xx/ES93x is overwritten by INCA 7HF4beta
EHI #101186 Update to BOA v1.4.0 latest version
EHI #101188 INCA-MCE10 ASAMMCD3MCV22: MCD3 server crashes after
measurement start
EHI #101195 CDM: [WBID2308879631] occures after copy action
EHI #101212 EE - "Database.LinDeLin" information appears when opening
ES593-D EE
EHI #101228 ES 581.3 support of 800 kBaud CAN message Sending
EHI #101232 ES581: CAN-Monitoring works not for two ES581 using at the
same time
EHI #101257 EE: Calc Signals are not any longer added to existing widget
via Add Variables
EHI #101278 Functions can not be added to CDM via VSD any more
EHI #101319 " Possible that after installation from INCA 7.0.0 HF4 Beta5
the EEdoes not open
Note: Reboot computer after installation required"
____________________________________________________________________________
INCA V7.0.0 HF 3
New feature
============================
EHI #2011400467 Together with bugfix for #2011400467 behavior enhanced.
CDM offers a new error icon (white cross 45° tilted on red ground) as
instant compare result when the source or one of the destinations is
not readable.
The new icon will be available beginning with INCA 7.0 HF3 / INCA 7.1.
Reason:
The existing CDM compare states "equal", "different", "not comparable"
did not cover the situation that the parameter exists in source and
destination but is somehow not readable.
See also EHI call 2011400467 Instant Compare shows wrongly equal
Note:
CDM offers no additional filter for error. As errors are exceptional CDM
visualizes these parameters always.
Release Notes INCA V700 HF25.docx Seite 49 von 55
Bug fixes and improvements
============================
KIR issue RP2011402642 solved:
EHI #2011402642 Timestamp measuring with ES581.x is not consistent
If ES581.2 OR ES581.3 is used for measurement
AND
INCA 6.2.1 HF22 or subsequent HFs
OR
"INCA ES581 second CAN Addon V6.2.1"
OR
INCA 7.0.0
is installed and used for measurement
THEN
Time stamps are not correctly recorded, but might fluctuate around the
correct time stamp.
This amount of fluctuation depends on the setup (e.g. number of recorded
items, transfer rate, raster) and might be typically +/- 20% around the
expected time stamp (1ms to 10ms but possibly even more; also reproduced
up to 40ms). The amount of fluctuation is smaller than the selected
measurement raster.
EHI #1003642 User Options Dialog - Unable to set focus to tab level using
Tab key
EHI #1004516 CDM is unable to list out slew variables in CSV file
EHI #1004544 Any way to save dataset comments and a2l filename information
using MCD3
EHI #1004556 Walkback when open experiment with missing raster in INCA 7.0
EHI #2002408 The decimals of Map are fixed by 16
EHI #2011400219 EditableState ist not updated
EHI #2011400467 Instant Compare shows wrongly equal
EHI #2011400467 Instant Compare shows wrongly equal
EHI #2011400901 CSE: If adding a new label to the CSE, the number of
decimals in the footer of the CSE is not correct.
EHI #2011401105 Timeout while flashing ECU
EHI #2011401927 INCA hangs when trying to change from Refence to Working Page
EHI #2011402018 Cursor up/down in the measure table is not supported
EHI #2011402055 CONVERT.DLL (INCA V6.2.1/21) can't convert HEX file which
include address 0xFFFFFFFF to BIN file.'
EHI #2011402099 CCP- communication with ECU is not possible.
Release Notes INCA V700 HF25.docx Seite 50 von 55
EHI #2011402384 Trigger definition not possible
EHI #2011402443 Unexpected PID 0 received (expected 2) on CanId 0x0759
EHI #2011402591 WBID2290662149 WB on Copy/Compare action
EHI #2011402630 Character is overwritten on calibration action
EHI #2011402709 WB while opening the EE
EHI #2011402835 [WBID25602121569] WB when using a INCA V6.2.1 Experiment and
change of the x/y axis in the 2D View of Combined Editor
EHI #2011402891 Disclaimer window pops up at each INCA start without
company network connection
EHI #96033 Sporadic corruption of errors raised from multiple asap1b
devices of the same type
EHI #98596 Crash when switching from numerical editor to slider
EHI #98659 WIN7: LIN and FLEXRAY does not work on Win7x64 Systems -
"INCA Loader II stop working"
EHI #98749 MDF4_CalibrationRecording: Cuboid Values are not recorded
correctly
EHI #99109 The configuration of output channels offers more devices than
expected for ES1310
EHI #100192 [WBID2855217949] when changing project in HWC
EHI #100261 J2534: Online Firmware Check processes hangs after closing INCA
EHI #100278 "UndefinedObject does not understand" occurs when listing
selected label in CDM"
EHI #100436 INCA-SIP: "Can't load toolbox D:\ETAS\INCA7.0\TOOLBOX\xsip.ic"
Error appears during start of INCA and SIP does not work anymore
Note: Solution requires also INCA-SIP V7.0.1.
EHI #100442 [WBID1936164439] UndefinedObject does not understand isDestroyed
EHI #100459 CDM Label List shows ERROR icons for groups
EHI #100576 I700 HF3 - Wrong Hotfix Package Versions in INCA I700HF
____________________________________________________________________________
INCA V7.0.0 HF 2
Note: HF2 was not released. Content is also included in HF3.
Bug fixes and improvements
============================
EHI #98502 ASAP2V16: Unexpected result when using Reset To Reference Page
Values for Rescale Axis Pairs using STATIC_RECORDLAYOUT
Release Notes INCA V700 HF25.docx Seite 51 von 55
EHI #98511 ASAP2V16: Wb([WBID101982755] after try to remove penultimate
Z2 Axis Point for 4-Cuboid with STATIC_RECORD_LAYOUT
EHI #98847 Target Server aborts recording due to a
"read Buffer Size Exceeded" Error
EHI #98896 CANMon - ES71x does not record CANMon data from internal CAN ports
EHI #99258 ASAMMCD3V2: Active workspace is opened instead of intended
one on SelectProject()
EHI #99407 Min size of customer instrument ist to big
EHI #99623 CEE3.3.0.14 During CCI Tests appear a "Fatal Application Error"
window.
EHI #99703 [WBID1759746211] Index out of range in argument 1 occurs
when switching CDM options"
EHI #99707 EE3.3.0.15_CCI_Datalogger: Data logger cannot be activated anymore.
EHI #100085 Incorrect gauge value ranges in VSD property grid
EHI #100244 Open EE: Exception occurs when opening EE with "Customer
Instruments" or creating "Customer Instrument" in EE
EHI #1004336 UFE icon not clear
EHI #1004531 WBID680084924 Walkback when convert experiment to INCA 5.x
EHI #90378 Font Size defined in the User Options is not used by INCA running
on OS with Japanese settings
EHI #2002099 Some INCA v6.2.1 user cannot change font setting for
measure and calibration window
EHI #2002105 INCA cannot set font size correctly on Japanese Windows and
Korean Windows.
EHI #2010406936 Font size for measurement table gets stored false into
INCA.INI
EHI #2011400609 Performance Problem with ASAM-MCD3 MC V1.0
EHI #2011400813 A path to DCM file in CDM is not correct
(Note: Solution already shipped with HF1)
EHI #2011400996 WBID1551991483 system error in combined editor
EHI #2011401162 API: OpenExperiment opens Active Workspace, not assigned
Workspace
EHI #2011401461 WBID2198815970 System error when changing distribution of
an EIP distribution curve
EHI #2011402033 Variable gets lost if copied by drag and drop
EHI #2011402113 Flashing via ETK is not possible: RUN_DLL error
Release Notes INCA V700 HF25.docx Seite 52 von 55
____________________________________________________________________________
INCA V7.0.0 HF 1
News
============================
Windows 7 SP1 is also supported
Bug fixes and improvements
============================
EHI #98217 ASAP2V16: Label using COMPU_METHOD LINEAR are not correct
handled when using it in INCA 6.2.1
EHI #98365 Targetserver crash
EHI #98369 ES720: restoration of MDF file in case of "Disk Full" failure
EHI #98401 Wb([WBID2460342884] UndefinedObject does not understand *) when
try to add label Combined Editor via Add Variable
EHI #98489 Measure Table does not use the correct Background Color after reo
EHI #98552 Wrong checksum calculation for 0x8005
EHI #98562 Time stamp jumps with ES590
EHI #98568 INCA uses the same recording time for every created file
EHI #98571 EW_I700_TF_DET55784_OpenEE_Testblocking: Context menus of
customer instrument are not recognized correctly by Silktest
EHI #98701 ES720: Restoration of Measure Data Files causes Exception
EHI #98759 INCA crashes in case of A2L file contains a CHARACTERISTIC with
a CUBOID
EHI #98765 Remapping of MCE variables leads to Walkback
EHI #98768 MDF package shipped with MDA 7.0.0 HF1
EHI #98817 [WBID2159497471] Walkback when open EE
EHI #98887 [WBID2194002561] WB when copying a VUI and deleting the old one
EHI #98896 CANMon - ES71x does not record CANMon data from internal CAN ports
EHI #98899 [WBID1122637292] CDFOptions does not understand getXmlIdentation)
when try to write file via Dataset -> Variables -> Write To CDF-File'
EHI #98907 I700HF1_TX_CAN_KWP Dowload differences and download dataset do no
more.
EHI #98917 HF1_TX_CAN_UDS Measurment terminates after a few seconds UDS and
KWP
EHI #98966 Failed MDF file merge results in left overs
EHI #98982 "INCA Regression Test Call for Call -
Release Notes INCA V700 HF25.docx Seite 53 von 55
ASCET process and IP Manager are hanging in Windows 7 #9885"
EHI #99107 "Calibration of Matrix results in INCA crash
NE internal for MCE"
EHI #99133 HF1_TX_EE:Functions are shown flat in the VSD Source Tree
independent from the settings in Variable Selection Preferences
EHI #99193 CSM-In case of high busload access violation in TargetServer
EHI #99612 KWP/UDS Systemexception at start of flashing
EHI #1004336 UFE icon not clear
EHI #1004410 INCA does not recognize connected ES715
EHI #1004465 INCA locks up when start and stop experiment using XCP on
CAN multiple times
EHI #1004474 Can not add slew calibration variables into CDM
EHI #1004499 [WBID3042542725]: WB when freeze working data with XETK V2
EHI #1004514 INCA-SIP: Multiple simulated XCP ECUs cause negative timestamps
to be generated in measure data recording
EHI #2002468 ES720: Unable to run ES4xx experiment that is created on
INCA Japanese version
EHI #2010404883 Start of recording is not possible
EHI #2010406255 LCA 3.4.0 - EE creates no dat-File at ConfigureDatalogger
with filename "".""
Note: This is only the INCA part of soltuion for call
2010406255. Complete solution requires also a update of the EE
EHI #2010406319 Calibrations won't be recorded
EHI #2010406513 Online Firmware Check does not work as expected
EHI #2010406556 WBID1534014050 System error occurs while trying to resize
window with measurement variables in ExpEnvironment
EHI #2010406614 Open the Config EE takes too much time
EHI #2010406853 CCP flashen ES581.2
EHI #2010406857 Array can not be selected in VSD if A2L uses MATRIX_DIM and
BIT_MASK
EHI #2010406903 XCP labels is lost w/o HW acces
EHI #2010406918 Restoring measure file does not work
EHI #2010406922 The background colour setting for the measurement table does
not get loaded if starting the EE
EHI #2010407069 INCA chrashes converting measure files
Release Notes INCA V700 HF25.docx Seite 54 von 55
EHI #2010407087 Calibration using Open EE Instruments does not work for
serial ETKs
EHI #2010407095 CDM stucks adding all labels to list
EHI #2011400044 HWC shows different Channel-Order for ES410 than
ES4xx-Configuration-Dialog
EHI #2011400196 [WBID3715872123]Walkback occurs when setting project file
to workspace
EHI #2011400245 [WBID1871838667] Walkback while initialising the experiment
EHI #2011400263 INCA stucks during ASAP3 test run
Following error of #2011401691 (see below)
EHI #2011401691 "Memory leak in Combined Editor
EHI #2011400285 Start of EE shows errors in monitor-window
EHI #2011400318 [WBID2505944818] UndefinedObject does not understand device"
when trying to write a template for converting an experiment
EHI #2011400417 [WBID1585120282]if attempt to start attached EE in the
attached WS
EHI #2011400449 [WBID761733007] initialisation of converted EE in INCA V5.x
generated walk back
EHI #2011400466 INCA generates measurement widgets with indentical
names - restoring display settings not reliable
EHI #2011400561 ASAP3: "Select Description and Binary File" from c:\
doesn't work
EHI #2011400609 Performance Problem with ASAM-MCD3 MC V1.0
EHI #2011400755 INCA crash when selecting signals in VSD recording only'
EHI #2011400825 WBID1508564322- write out of A2L file is not possible
EHI #2011400996 WBID1551991483 system error in combined editor
EHI #2011401107 [WBID2561534467] when performing calibration in Experiment.
EHI #2011401108 Problem using SET LOOKUP TABLE and grouped devices
EHI #2011401332 WBID1364534773 after Flash and Checksum within KWP2000 /
Incircuit2
EHI #2011401604 No OHI connection to device via ES690
EHI #2011401616 Difference in CDM not detected in case of tolerant compare
EHI #2009406108 and 98313 CCP download differences not performed if global
checksum of the WP is identical, single ranges not
Release Notes INCA V700 HF25.docx Seite 55 von 55
_______________________________________________________________
Contact, Support and Problem Reporting
For details of your local sales office as well as your local technical support
team and product hotlines, take a look at the ETAS website:
ETAS subsidiaries WWW: www.etas.com/en/contact.php
ETAS technical support WWW: www.etas.com/en/hotlines.php
_______________________________________________________________
Copyright and Trademark Attributions
The data in this document may not be altered or
amended without special notification from ETAS GmbH.
ETAS GmbH undertakes no further obligation in relation
to this document. The software described in it can
only be used if the customer is in possession of a
general license agreement or single license. Using
and copying is only allowed in concurrence with the
specifications stipulated in the contract. Under no
circumstances may any part of this document be copied,
reproduced, transmitted, stored in a retrieval system
or translated into another language without the
express written permission of ETAS GmbH.
© Copyright 2014 ETAS GmbH, Stuttgart
The names and designations used in this document are
trademarks or brands belonging to the respective owners.