Inspection References Hand Book-2

INSPECTION REFERENCES HAND BOOK

Page 1 of 22

REFERENCE HAND BOOK FOR OFFSHORE FABRICATION

Ishtiaq Ahmed

NAPID/OPIS/ FPIU

Inspection References


Page 2 of 22

Table of contents: 1. Offshore Structures fabrication & installation.………………………….. 2. Piping Welding…………………………………………………………………………. 3. Piping Fabrication & Installation ………………………………………………. 4. Piping pressure Testing…………………………………………………………….. 5. Pipe lines (offshore)…………………………………………………………………... 6. Valves Receiving & Testing ………………………………………………………. 7. Positive Displacement Pumps …………………………………………………… 8. Centrifugal Pumps ……………………………………………………………………. 9. High Integrity Protective System (HIPS)…………………………………….. 10. Pressure Vessels ………………………………………………………………………. 11. Surface Preparation and Coating Application...…………………………

11.1 Surface Preparation 11.2 Liquid Coating Application (Internal & External) …………… 11.3 FBE Coating Application (Internal & External) …………….…

12. Cathodic Protection…………………………………………………………………. 13. Switch gear……………………………………………………………………………… 14. Cables and trays……………………………………………………………………… 15. Electronic control systems……………………………………………………….


Page 3 of 22

Reference Hand Book for Offshore Fabrication

“This Hand book has been developed for the easy identification &

selection of applicable International Codes, Saudi Aramco Standards,

Specification and other applicable reference documents for all offshore

fabrication related activities for the Oil and Gas Projects. The purpose

of this handbook is to use as an easy reference guide by inspection

personnel and development of new engineers & trainees by identifying

inspection requirements and build up the minimum awareness in all

specialties related to our business”.

*********************

NAPID-OPIS-FPIU


Page 4 of 22

Abbreviations: SAES - Saudi Aramco Engineering Standard

SAEP-Saudi Aramco Engineering Procedure

SAMSS-Saudi Aramco Material System Specification

SAIC- Saudi Aramco Inspection Check list

SATIP-Saudi Aramco Typical Inspection plan

SATR-Saudi Aramco Test Report

ASME –American Society for Mechanical Engineers

API-American Petroleum Institute

ISO-International organization for standardization

NACE-National Association of corrosion Engineer

SSPC-Steel structure painting council

IEEE- Institute of electrical & electronics engineers

NEMA-National Electrical Manufacturers association

IEC-International electro technical commission

*********************


Page 5 of 22

1. Offshore Structures Fabrication & Installation

International standards

AWS D1.1 Structural Welding Code

API RP 2A Recommended practice for planning, designing and constructing for offshore structures

API RP 2X Recommended practice for ultrasonic and magnetic examination of offshore structural Fabrication and guide lines for qualification of technicians

API 2H Specification for Carbon Manganese steel plate for offshore structures

API 2W Specification for steel plates for offshore structures produced by thermo mechanical control processing

API 5L Specification for line pipe

ASTM A6 Standard Specification for General Requirements for rolled structural steel bars, plates, shapes and steel pilings

BS-EN 10025-6 Hot rolled products of structural steels

SAES

SAEP

SAMMS

SAES-M-005 Design and Construction of Fixed offshore Platform

SAES-W-13 Welding requirements for offshore structures 12-SAMMS-018 Structural Plates, rolled shapes and tubular specification

for fixed offshore platforms

DE-119885 Procedure for quality assurance and quality control (construction of offshore platforms and pipe lines)

DE-119887 Procedure for structural materials DE-119893 Procedure for structural fabrication, load- out and tie-down of

offshore structures DE-119951 Procedure for Monel sheathing installation

SAIC

SATR

SATIP

SAIC-M-2003 Receiving Inspection of structural steel SAIC-M-2005 Storage, Handling and preservation of structural steel

materials and components SAIC-M-2006 Inspection of support foundation prior to structure or

equipment installation

SAIC-M-2022 Pile driving Procedure (Trials, splicing, NDT)


Page 6 of 22

2. Piping Welding International standards

ASME B31.3 Process Piping ASME BPV Section IX Welding procedure and welder qualification

SAES

SAEP

SAMMS

SAES-W-11 Welding Requirements on plot piping SAES-W-14 Weld Overlays and welding of clad materials SAES-W-16 Welding of special corrosion resistant materials SAES-W-19 Girth welding requirements of clad pipes SAEP-324 Certification Review and Registration of project welders 20-SAMSS-001 Welding and brazing consumables

SAIC

SATR

SATIP

SAIC-W-2001 Review WPS and Process Control Procedure (Plant piping) SAIC-W-2004 Post Weld Heat treatment (PWHT) for on plot piping SAIC-W-2005 Pre Welding Inspection (shop & field) of plant piping SAIC-W-2006 In process Welding Inspection SAIC-W-2007 Post Welding Visual Inspection Plant piping SAIC-W-2008 Review procedure Weld ID and traceability process control

tracking SATR-W-2003 Welder performance qualification test record SATR-W-2004 PWHT request


Page 7 of 22

3. Piping Fabrication & Installation International standards

ASME B31.3 Process Piping

ASME B16.5 Pipe flanges and flanged fittings ASME PCC 1 Guide lines for pressure Boundary bolted flange joint

assembly

SAES

SAEP

SAMMS

SAES-L-105 Material specification for piping components

SAES-L-108 Selection of valves SAES-L-109 Selection of pipe flanges, stud bolts and gaskets

SAES-L-110 Limitations on piping joints and components

SAES-L-350 Construction of piping systems SAEP-351 Bolted flanged joints assembly

DE-119888 Procedure for fabrication and installation of platform piping

SAIC

SATR

SATIP

SATIP-L-350-01 on Plot metallic piping installation

SATIP-L-350-02 Piping Tie-in installation for plant piping

SAIC-L-2001 Review Procedure internal cleaning for plant systems, plant equipment & pipe lines

SAIC-L-2002 Review procedure-Flange joint assembly and gasket installation

SAIC-L-2003 Review procedure-piping materials traceability

SAIC-L-2005 Receiving Inspection of pipe and pipe nipples (plant piping) SAIC-L-2006 Receiving Inspection of pipe fittings and flanges SAIC-L-2007 Receiving Inspection of gaskets SAIC-L-2011 Piping pre installation inspection prior to on plot work

including spec check

SATR-L-2001 Flange Joint tightening inspection report SAIC-L-2012 Pipe laying, spool erection & assembly on pipe racks and

sleeper ways SAIC-L-2013 Inspection of piping branch connections SAIC-L-2014 Inspection of bolted flange joint assembly

SAIC-L-2015 Inspection of threaded joint engagement (gap control) SAIC-L-2016 Inspection of venturi, restriction orifice and flow orifice

SAIC-L-2017 Piping/Equipment cleaning inspection

SAIC-L-2018 Inspection of pipe support and pipe anchor installation

SAIC-L-2022 Final piping punch listing (piping reinstatement)


Page 8 of 22

4. Piping Pressure Testing International standards

ASME B31.3 Process Piping

ASME PCC 1 Guide lines for pressure Boundary bolted flange joint assembly

SAES

SAEP

SAMMS

SAES-A-004 General Requirements for pressure testing

SAES-A-007 Hydro testing Fluids and lay up procedures

SAES-L-150 Pressure testing of plant piping and pipe lines SAES-L-109 Selection of pipe flanges, stud bolts and gaskets

SAEP-351 Bolted flanged joints assembly

SAEP-1160 Tracking & reporting of welding, NDT and pressure testing of capital projects

SAES-J-600 Pressure Relief Devices GI 0002.102 Pressure Testing Safely DE-119955 Procedure for hydrostatic testing of platform piping and

submarine pipe lines SAES-L-125 Safety Instruction sheet for piping and pipe lines

SAIC

SATR

SATIP

SATIP-A-004-002 Hydrostatic testing of on plot piping

SAIC-L-2001 Review Procedure internal cleaning for plant systems, pipe lines

SAIC-L-2002 Review procedure-Flange joint assembly and gasket installation

SAIC-L-2007 Receiving Inspection of gaskets SAIC-A-2003 Review of test packs preparation

SAIC-A-2008 Verify test medium for hydrostatic Testing & lay-up

SAIC-A-2009 Verify test equipment SAIC-A-2010 Pretest punch list on plot piping

SATR-A-2007 Pre pressure test checklist SATR-A-2002 Pressure test certificates-pressure gauges

SATR-A-2006 Pressure test certificates-Relief Valves SATR-A-2004 Pressure test certificates-Pressure recorder SATR-A-2005 Pressure test certificates-Temperature recorder SATR-A-2003 Pressure test certificates-Temperature gauges SATR-A-2014 Water Chemistry Test report


Page 9 of 22

5. Pipe Line (offshore): International standards

ASME B31.8 Gas Transmission & Distribution piping systems ASME B31.4 Pipe Line Transportation system for liquid hydrocarbons and

other liquids API standard 1104 Welding of pipe line and related facilities API RP 1110 Recommended Practice for the pressure testing of steel pipe

lines for the transportation of gas, petroleum gas API 5L Specifications for line pipe

API 5L D Specification for CRA clad or lined steel pipe

API RP 1111 Design, Construction, operation & maintenance of offshore hydrocarbon pipe lines

SAES

SAEP

SAMMS

SAES-L-410 Design of pipe lines SAES-L-420 Scraper traps station piping and appurtenances

SAES-L-850 Design of submarine pipe lines and risers

SAES-L-450 Construction of on land and near shore pipe lines SAES-L-488 Pipe line cleanliness requirement for hydrocarbon services SAES-L-810 Design of piping on offshore structures SAES-W-12 Welding requirements for pipe lines SAES-L-125 Safety Instruction sheet for piping and pipe lines DE-119886 Procedure for fabrication and installation of risers and

submarine spool pieces DE-119954 Procedure for fabrication and installation of sub marine pipe

lines DE-119955 Procedure for hydrostatic testing of platform piping and

submarine pipe lines 01-SAMSS-035 API Line Pipe

02-SAMSS-009 Design and fabrication of scraper traps

01-SAMSS-012 Submarine pipe weight coating

01-SAMSS-039 Induction& Furnace hot pipe bends

01-SAMSS-044 CRA Clad pipe spools 01-SAMSS-048 CRA Clad or lined pipe

FORM-175- 026800 Scraper trap

SAIC

SATR

SATIP

SAIC-L-2134 Storage and preservation of scraper traps & appurtenances SAIC-L-2135 Installation of scraper trap and appurtenances

SAIC-W-2044 Receiving Inspection of welding consumables SAIC-W-2038 WPS Review

SAIC-W-2046 Control of welding consumables SAIC-W-2048 Pre-welding, in process and post weld inspection

SATR-W-2007 Daily weld fit up and production report pipe line

SATR-W-2008 Weld summary

SATR-W-2012 Hardness Test report SATIP-W-12-01 Welding of pipe lines


Page 10 of 22

6. Valves Receiving & Testing International standards

ASME B16.34 Valves, Flanged, threaded and welding end

API 598 Valves Inspection and Testing

API SPEC 6A Specification for well head and Christmas tree equipment API SPEC 6D Specification for pipe line valvesWellhead and Christmas Tree

Equipment

SAES

SAEP

SAMMS

SAES-A-004 General Requirements for pressure testing

SAES-L-108 Selection of valves SAES-J-700 Control Valves

SAEP-35 Valves Handling, Hauling, Receipt Tests and Storage

04-SAMSS-001 Gate Valves

04-SAMSS-002 Globe Valves 04-SAMSS-005 Check Valves, Swing type

45-SAMSS-005 Valves and Well head Equipment requirements as per API SPEC 6A

04-SAMSS-035 General Requirement for valves 04-SAMSS-048 Valve Inspection and Testing Requirements 04-SAMSS-003 Additional Requirements for low temperature valves 04-SAMSS-049 Inspection and Testing Requirements for API SPEC 6A,

10000 PSI Valves 04-SAMSS-051 Ball Valves API SPEC 6D

04-SAMSS-052 Ball Valves, API SPEC 6A

SAIC

SATR

SATIP

SATIP-L-108-1 Valve Inspection, testing and installation

SAIC-L-2040 Receiving Inspection of Manual Valves SAIC-L-2041 Storage and preservation of valves SAIC-L-2042 Field Hydro testing of isolation valves SAIC-L-2043 Valve Installation Inspection & Valve Testing

SATR-L-2001-V Pressure test report, valve inspection and field testing

Form 175-043000 Valves Material Certification requirements Form 175-043600 Metallic & nonmetallic valves Form 175-043601 Low severity Valves Form 175-045600 Inspection and Testing Requirement for API SPEC 6A,

10000 PSI Valves


Page 11 of 22

7.Positive Displacement Pumps International standards

API 675 Positive Displacement Pumps-Controlled Volume API 686 Recommended practice for Machinery Installation and design API 674 Positive Displacement Pumps-Reciprocating

SAES

SAEP

SAMMS

SAES-G-006 Positive Displacement Pumps Controlled Volume SAES-A-105 Noise Control 31-SAMSS-009 Positive Displacement Pumps Controlled Volume SAIR-175-311500 Positive displacement Pumps controlled volume

SAIC

SATR

SATIP

SAIC-G-2009 Receiving Inspection of Positive Displacement Pumps SAIC-G-2010 Handling, storage and preservation inspection of positive

displacement pumps SAIC-G-2014 Installation of Mechanical components of lubrication shaft

sealing and oil system for rotating equipment SAIC-G-2021 Mounting plate installation and leveling for pump SATR-G-2004 Pump alignment record sheet SATR-G-2005 Mounting plate level data sheet SATIP-G-006-1 Positive displacement pumps SATIP-G-115-01 Lubrication, shaft sealing of oil systems


Page 12 of 22

8. Centrifugal Pumps International standards

API 610 Centrifugal Pumps API 682 Shaft sealing system for centrifugal and rotary pumps API 686 Recommended practice for Machinery Installation and design

SAES

SAEP

SAMMS

SAES-G-005 Centrifugal Pumps SAES-A-105 Noise Control 31-SAMSS-004 Centrifugal Pumps SAIR-FORM175-310510 Molten Sulfur Pumps SAIR-FORM175-310700 Main fire water pumps

SAIC

SATR

SATIP

SAIC-G-2002 Receiving Inspection of centrifugal Pumps

SAIC-G-2003 Handling, storage and preservation inspection of centrifugal pumps

SAIC-G-2005 Inspect suction and discharge piping connections SAIC-G-2007 Final Inspection/Walk through of pump installation

SAIC-G-2021 Mounting plate installation and leveling for pump

SATR-G-2004 Pump alignment record sheet SATR-G-2005 Mounting plate level data sheet SATIP-G-005-1 Centrifugal Pumps


Page 13 of 22

9. High Integrity Protective System (HIPS) International standards

API RP 14C Analysis, Design, Installation and testing of basic surface safety systems on offshore production platforms

API RP 14J Design and hazards analysis for offshore production facilities API STD 6FA Specification for fire test for valves API 6A Specification for well head and Christmas tree equipment API RP 552 Transmission systems API RP 554 Process Instrumentation and Control

SAES

SAEP

SAMMS

SAES-J-003 Instrument basic design criteria

SAES-J-601 Emergency shut down and isolation systems

SAES-J-902 Electrical systems for instrumentation. SAEP-354 High integrity protective system design requirements. 01-SAMSS-017 Auxiliary piping for mechanical equipment 04-SAMSS-003 Additional Requirements for low temperature valves 04-SAMSS-035 General Requirements for Valves 04-SAMSS-048 Valve Inspection and testing requirements

34-SAMSS-820 Instrument control cabinets 34-SAMSS-831 Package Unit Instrumentation

SAIC

SATR

SATIP


Page 14 of 22

10.Pressure Vessels International standards

ASME Section-VIII Div.1 Rules for Construction of Pressure Vessels ASME Section-VIII Div.2 Rules for Construction of Pressure Vessels

Alternative Design Rules ASME Section-IX ASME Section-II Part A & C ASME Section-V

SAES

SAEP

SAMMS

SAES-W-010 Welding Requirements for Pressure Vessels SAES-A-004 General Requirements for Pressure Testing SAES-A-004 Hydrostatic Testing Fluids & Lay-Up Procedures SAES-D-001 Design Criteria for Pressure Vessels 32-SAMSS-004 Manufacture of Pressure Vessels 2694-ENG Safety Instruction Sheet-Vessels 9527-ENG Pressure Vessel Data Sheet PIP-VEFV1100 Vessels/S&T Heat Exchanger Standard Details SAIR-FORM175-321900 Inspection & Testing Requirements for Pressure

Vessels SASD- AB-036322 Anchor Bolt Details SAES-X-500 Cathodic Protection Vessels and Tank Internals

SAIC

SATR

SATIP

SAIC-D-2002/2003 Material Receiving Inspection of Pressure Vessels (External/Internal)

SAIC-D-2004 Material Receiving Inspection of Ladders, Platforms & other Structural Attachments of Pressure Vessels

SAIC-D-2005 Handling, storage and preservation inspection of Pressure Vessels

SAIC-D-2006 Pre-Installation Inspection SAIC-D-2007 Equipment Installation-Alignment & Elevation Survey

SAIC-Q-1048 Grouting Inspection SAIC-D-2008 Inspection of Vessel Trim Installation

SAIC-D-2009 Tray & Internal Component Installation

SATR-D-2004 Tray Testing

SATR-D-2003 Vessel Closure Inspection(Box-Up) SAIC-D-2012 Final Inspection/Punch Listing for Re-instatement SATR-D-2001 Alignment Inspection Record for Horizontal Vessels SATR-D-2002 Alignment Inspection Record for Vertical Vessels SATR-D-2003 Vessel Closure Certificate

SATR-D-2004 Tray Test Report SATIP-D-001-01 Inspection & Test Plan for Installation of Pressure

Vessel


Page 15 of 22

11. Surface Preparation and Coating Application 11.1 Surface preparation


ISO-8501-Preparation of steel substrates before application of paints and related products-Visual assessment of surface cleanliness

ISO-8502-Preparation of steel substrates before application of paints and related products -Tests for the assessment of surface cleanliness

ISO-8503-Preparation of steel substrates before application of paints and related products- Surface roughness characteristics of blast-cleaned steel substrates

ISO-8504-Preparation of steel substrates before application of paints and related products - Surface preparation methods

SIS 05-59-00 Pictorial Surface Preparation Standard for Painting Steel Surfaces (Swedish Standards Institution)

ISO 12944 (Part 1 to 8) Corrosion Protection of Steel Structures by Protective Paints Systems

SSPC AB Abrasive Material Specification

SSPC-Vis 1 Guide to Vis 1 - 89 - Visual Standard for Abrasive Blast Cleaned Steel

SSPC-SP1 Solvent Cleaning SSPC-SP2/St2 Hand Tool Cleaning SSPC-SP3/St3 Power Tool Cleaning SSPC-SP7/Sa1 Brush-off Blast Cleaning (NACE No. 4) SSPC-SP6/Sa2 Commercial Blast Cleaning (NACE No. 3) SSPC-SP10/Sa2.5 Near White Blast Cleaning (NACE No. 2) SSPC-SP5/Sa3 White Metal Blast Cleaning (NACE No. 1) NACE-RP0287 - Field Measurement of Surface Profile of Abrasive

Blast Cleaned Steel Surfaces Using a Replica Tape GI 0006.021 Safety Requirements for Abrasive Blast Cleaning


Page 16 of 22

11.2 Liquid Coating Application (Internal & External).


SSPC-PA Coating Application Specification

ASTM D5162 Holiday Test

SAEP

SAES

SAMSS

SAEP-316 Performance Qualification of Coating Personnel SAES-H-001 - Coating Selection and Application Requirements for Industrial

Plants and Equipment SAES-H-002 - Internal and External Coatings for Steel Pipelines and Piping

SAES-H-004 - Protective Coating Selection and Application Requirements for Offshore Structures and Facilities

SAES-H-101V - Approved Saudi Aramco Data Sheets - Paints and Coatings SAES-H-102 - Safety Requirements for Coating Applications

SAES-H-200 - Storage, Handling and Installation of Externally Coated Pipe

SAES-B-067 Safety Identification and Safety Colors SAES-B-069 Emergency Eyewashes and Showers DE-119889 Procedure for painting of offshore platforms 175-091900 - COATING: SHOP APPLIED; For Tanks, Piping, Pipelines (and

Associated Appurtenances & Fittings), Structures, Process Equipment 09-SAMSS-069 - Qualification Requirements for Epoxy Coatings for

Atmospheric Service

SATIP SAIC

SATR

SATIP-H-100-01 Paint Application of Liquid Coating Systems (Industrial Facilities)

SAIC-H-2023 Coating Procedure review

SAIC-H-2010 Coating Personnel Qualification & Certification Card Review

SAIC-H-2024 Verification and Visual Inspection of Paints and abrasives material receiving

SAIC-H-2025 Storage and Handling of Paints and Abrasives materials SAIC-H-2026 Equipment Inspection

SAIC-H-2027 Inspection of Surface Preparation & Prior to Application of liquid coating systems (New Installations)

SAIC-H-2028 In-Process Inspection of Primer Coat OR First Coat Application

SAIC-H-2029 Inspection of Primer Coat prior to top coating


Page 17 of 22

11.3 FBE Coating Application (Internal & External) International standards

NACE - SP0188-2006 (formerly RP0188) - Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrates

NACE - TM0186-2002 Holiday Detection of Internal Tubular Coatings of 250 to 760 μm (10 to 30 mils) Dry-Film Thickness

NACE - SP0274-2011 (formerly RP0274) - High-Voltage Electrical Inspection of Pipeline Coatings Prior to Installation

SAEP SAES SAMSS

SAEP-316 Performance Qualification of Coating Personnel SAES-H-002 - Internal and External Coatings for Steel Pipelines and Piping SAES-H-102 Safety Requirements for Coating Applications SAES-H-200 - Storage, Handling and Installation of Externally Coated Pipe SAES-H-201 General Specifications for Over-the-Ditch External and Internal

FBE Coating of Field Girth Welds 09-SAMSS-089 Shop-Applied External Fusion Bonded Epoxy Coating for Steel

Line Pipes 09-SAMSS-091 Qualification Requirements for Shop-Applied Internal FBE

Coatings 09-SAMSS-060 Packaging Requirements for Coatings

SATIP SAIC SATR

SATIP-H-002-08 Internal FBE Coating of Field Girth Welds & Repairs. SAIC-H-2057 Procedure for Internal FBE Coating of Field Girth Welds &

Repairs CSD approved SAIC-H-2010 Coating Personnel Qualification & Certification Card Review SAIC-H-2058 Verification of FBE Powder materials and Abrasive materials

including Storage and Handling (APCS-102) SAIC-H-2013 Inspection and verification of FBE Coating application

equipment SAIC-H-2059 Surface Preparation of Pipe Joints for Field Internal FBE Coating. SAIC-H-2060 In-Process & Final Inspection of FBE coating Application on

Internal Field Girth Welds (APCS 102 Application) SATR-H-2004 Coating Equipment Check Sheet SATR-H-2008 Holiday Test Report SATR-H-2009 FBE Coating Curing Test SATR-H-2010 FBE Coating Adhesion Test SATR-H-2011 FBE Coating Surface Preparation SATR-H-2012 FBE Coating In process


Page 18 of 22

12. Cathodic Protection International standards

NACE-RP-0387 Metallurgical and inspection requirements for cost sacrificial

anodes for offshore applications NACE-TM-0190 Standard test method for impressed current test method for

laboratory testing of aluminum anodes

SAEP

SAES

SAIR

SAMSS

SAES-X-300 Cathodic Protection of marine structures SABP-X-003 Cathodic Protection Installation Requirements GI-0428-001 Cathodic Protection Responsibilities 17-SAMSS-006 Galvanic Anodes for cathodic Protection

17-SAMSS-007 Impressed current anodes for cathodic protection

17-SAMSS-008 Junction boxes for cathodic protection

SAEP-332 Cathodic protection commissioning

SAEP-333 Cathodic protection monitoring

SATIP SAIC

SATR

SATIP-X-400-01 Galvanic Cathodic Protection

SATIP-X-600-02 Impressed Current Cathodic Protection

SATR-X-3101 Galvanic CP Testing

SATR-X-3201 DC Cable Holiday Testing

SATR-X-3202 DC Rectifier Testing

SATR-X-3203 Plant Potential Survey Testing

SATR-X-3204 External Tank Bottom Testing

SATR-X-3205 Internal Tank Bottom Testing

SAIC-X-3001 Exothermic Welding Tools & Materials - Material Receiving

SAIC-X-3002 CP Accessories - Material Receiving

SAIC-X-3003 Exothermic Welding

SAIC-X-3101 Galvanic Anodes for CP (Aluminum, Magnesium, and Zinc Anodes) - Material Receiving

SAIC-X-3102 Galvanic CP Test Stations / Junction Boxes - Material Receiving

SAIC-X-3103 Galvanic CP Anode Installation and Pre-Commissioning

SAIC-X-3104 Galvanic CP Test Station Installation and Pre-Commissioning

SAIC-X-3105 Galvanic CP Cable Installation, Termination, and Identification

SAIC-X-3201 CP Rectifier - Material Receiving

SAIC-X-3202 Impressed Current Anode - Material Receiving

SAIC-X-3203 Impressed Current CP Cable - Material Receiving

SAIC-X-3204 DC Rectifier Installation and Pre-Commissioning

SAIC-X-3205 Impressed Current CP Anode Installation and Pre-Commissioning

SAIC-X-3206 Impressed Current CP Deep Anode Bed Installation and Pre-Commissioning

SAIC-X-3207 Impressed Current CP Cable Installation, Termination, and Pre-Commissioning


Page 19 of 22

13. Switchgear and control equipment: International standards

IEEE C37.04 rating structure for high voltage circuit breakers IEEE C37.09 Standard test procedures for high voltage circuit breakers IEEE C37.54 Conformance test procedures NEMA ICS 7 Industrial control and system adjustable speed drives

SAEP

SAES

SAIR

SAMSS

SAES-P-116 Switchgear and control equipment SAES-P-114 Power system and equipment protection 16-SAMSS-502 Metal enclosed low voltage switch gear assemblies 16-SAMSS-506 In-door control gear high voltage

SATIP SAIC

SATR

SATIP-P-116-01 Medium Voltage switch gear SAIC-P-3813 MV Switchgear - Metal-Clad Switchgear (Indoor/Outdoor)

Material Receiving SAIC-P-3814 MV Switchgear - SF6 Switchgear (Outdoor) Material Receiving SAIC-P-3815 MV Switchgear - Manual SF6 Circuit Breaker Material Receiving SAIC-P-3820 MV Switchgear - Outdoor SF6 Switchgear Installation and

Pre-Commissioning


Page 20 of 22

14. Cables and trays: International standards

IEEE 835 IEEE standard power ampacity tables

SAEP

SAES

SAIR

SAMSS

SAES-P-104 Wiring methods and materials SAES-B-068 Electrical area classification SAES-P-111 Grounding 15-SAMSS-502 Medium voltage power cable 5kV through 35 kV

SATIP SAIC

SATR

SATIP-P-104-01 Low Voltage (up to 1 kV) Power Cable and Building Wire SATIP-P-104-02 Medium Voltage Cable and Conductors (1.001 kV to 35 kV) SAIC-P-3201 Cable Storage, Handling, and Preservation SAIC-P-3202 Low Voltage UL/NEC Power and Control Cable and Wire

Material Receiving SAIC-P-3204 Low Voltage IEC Armored Cable, Material Receiving SAIC-P-3205 Low Voltage IEC Unarmored Cable, Material Receiving SAIC-P-3206 Low Voltage Power Cable Accessories, Material Receiving SAIC-P-3207 Low Voltage Power and Control Cable, Installation and Pre-

Commissioning SAIC-P-3208 Low Voltage Building Wire, Installation and Pre-

Commissioning SAIC-P-3209 Hazardous Location Conduit / Cable Seal Fitting Installation and

Sealing SAIC-P-3212 Medium Voltage IEC Cable, Material Receiving SAIC-P-3214 Medium Voltage Cable, Installation and Pre-Commissioning

(Rated 5KV through 35KV) SATR-P-3201 Low Voltage Power and Control Cable (On Reel), Continuity and

Megger Insulation Resistance Testing SATR-P-3202 Low Voltage Building Wire (On Reel), Continuity and Megger

Insulation Resistance Testing SATR-P-3206 Low Voltage Building Wire, Termination Torque Testing SATR-P-3207 Medium Voltage Power Cable (On Reel) Continuity and Megger

Insulation Resistance Testing SATR-P-3208 Medium Voltage Power Cable (Installed) Continuity and

Megger Insulation Resistance Testing


Page 21 of 22

15. Electronic Control systems: International standards

IEC-61131-3 Programmable controllers & programming languages

SAEP

SAES

SAIR

SAMSS

SAES-P-104 Wiring methods and materials SAES-Z-010 Process automation design SAES-Z-001 Process control systems 23-SAMSS-010 Distributed control systems Form-175-230100 Distributed control systems

SATIP SAIC

SATR

SATIP-J-902-05 Electronic Control Systems - DCS / ESD / PLC SAIC-J-6802 Electronic Control Systems - DCS/ESD - I/O and CPU Cabinets and

Operators Consoles - Material Receiving SAIC-J-6803 Electronic Control Systems - PLC - Material Receiving SAIC-J-6804 Electronic Control Systems - DCS / ESD Manufacturer's Data

Highway Cable - Material Receiving SAIC-J-6805 Electronic Control Systems - DCS / ESD - I/O and CPU

Cabinets and Operators Consoles - Installation and Pre- Commissioning SAIC-J-6806 Electronic Control Systems - PLC (Stand-Alone as well as

Integrated with DCS) – Installation and Pre-Commissioning

SAIC-J-6807 Electronic Control Systems - DCS/ESD Manufacturer's Data

Highway Cable - Installation and Pre-Commissioning


Page 22 of 22

Documents

Inspection References Hand Book-2