Installation Abovethe CooktopOven...Installation Instructions Abovethe CooktopOven JVM1490,JVM1790,SCAI000,SCAI001 Questions?Call800-GE-CARES(800-432-2737)or visitour _ ebsite at:

InstallationInstructions

AbovetheCooktopOvenJVM1490,JVM1790,SCAI000,SCAI001

Questions?Call 800-GE-CARES(800-432-2737)or visit our _ ebsite at: ge.com IBEFORE YOU BEGINRead these instructions completely and carefully.

• IMPORTANT - S.,e_heseinstructions for local inspector's use.

• IMPORTANT - Obse,,e.llgo_,ei'iliil o codes _lIl(1 oI'diIl_lIlCes.

• Note to Installer - Be sure to lea',e these

instructions with the (_onsumer.

o

o

o

o

Note to Consumer _ Keep these

instructions for future reterence.

Skill level - Installation of this appliance reqtfiresbasic mechanical and electrical skills.

Proper installation is the responsibility of the installer.

Product thilure due to improper installation is notcoxered trader the _arrantx.

LA SECCION EN ESPAI_OL

EMPIEZA EN LA PAGINA 25.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Instructions

CONTENTS

General information

hnportant Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Hood Exhaust ...................................................... 4, 5

Damage - Shipment/InstaJlation .............................. 6

Parts Included. ......................................................... 6

Tools You Will Need ................................................ 7

Mounting Space ...................................................... 7

Step-by-step installation guide

Placement of Mounting Plate ............................ 8-10

Removing tire Mounting Plate ...................... 8

Finding the _4all Studs ................................. 8

Determining _.lll Plate l.oration .................. 9

Aliguiug the _4hll Plate ............................... 10

Installation Types .................................. 11-22

[]Outside Top ............................Exhaust 12-14

Attach Mounting Plate to W;dl ....... 12

Preparation of Top Cabinet .......... 13

Checking 1or Proper Damper()peration ............................................ 13

Mount the Oveu .................... 13, 14

Ac!just the Exhaust Adaptor .......... 14

Connerting Durtwork .......................... 14

_ ()utside Back Exhaust 15-18

Preparing Rear _'V;dl forOutside Bark Exhaust .......................... 15

Attach Mounting Plate U>_4"01 ...... 15, 16


Adapting Blower tot OutsideBack Exhaust.. .............................. 16, 17

Mount the Oveu .................................. 18

Redrculating ........................................ 19-22

Attach Mounting Plate to _4.fll ....... 19


Adapting Blowerfor Redrrulation ......................... 20, 21

Mount the Oveu .................... 21, 22

Installing the Charcoal Filter ...... ........ 22

Before You Use Your Oven .................................. 23

Seccion en Espafiol ........................................ 25-47

2


mMPORTANT SAFETY mNSTRUCT ONS

CAWFION: For personal safety, the momlting surfacemust be capable of supporting the cabinet load, inaddition to the added weight of this 62%85 poundproduct, plus additional oven loads of up to 50 poundsor a total weight of 117_135 pounds.

CAIYFION: For personal safety, this product c_otbe installed in cabinet arrmlgements such as an island ora perfinsuia. It must be mounted to BOTH a top cabinetAND a wall.

NOTE: For easier insta]iation and personal safety, it isrecommended that two people install tt_s product.

IMPORTANT PLEASE R1LM) CARFFULL_: FOR

PERSONAL SAFETY; THIS APPLIANCE MUST BEPROPERLY GROUNDED TO AVOID SEVERE ORFNFAL SHOCK.

The power cur'd of this app]iance is equipped witha three=prong (grounding)plug which mates witha standard three=prong(gromlding) wail receptacleto mininlize the possibilityof electric shock hazard

from tiffs app]iance.

Insurepropergroundexistsbeforeuse

Yon should have the wail receptacle and circuit checkedby a qualified electrician to make sure the receptacle isproperly grounded.

Where a standard two-prong wall _eceptade isencountered, it is very inlportant to have it replacedwith a properly grounded three=prong wail receptacle,installed by a qualified electridan.

DO NO% UNDER ANY CIRCUMST_CES, CU_[;DI_"ORM, OR REMOVE ANY OF THE PRONGSFROM THE POWER CORD. DO NOT USE ¼rITHAN FXTENSION CORD.

ELECTRICALREQUIREMENTSProduct rati]/g is 120 volts AC, 60 Hertz, [5 amps, am]1.70 kilowatts. This product must be co]/m/ected toa slq_p]} ci]mdt o{ the propervoItq<,e_ am] {reql_e]/c}.

\_ire si zem Ilst CO]/['()]q]/ It) the req Hi rein el/ts of the

Natiomd Electrical Code or tile [)revaiIim/g, local codefor this kilowatt mtim/g. The [)o]ver sIl[)pl_ co]'d amid

>lug sholdd be lu'm]<,ht to a separate 15 to 90= amperebra_]c]] circlfit si_]g]e groin]deal ola]et. The ]mt]et boxshould be located i_i tile cabim/et above tile ore]/. Tile

outlet box am] suppI} circuit sho_ld be ira/stalled bv

a qlmIilied eIectricim/am[ coului'm to the Nati]malElectrical Code ur the prevaili_/g local code.

3


HOOD EXHAUSTNOTE: Read these next two pages tufty if you plml to vent your exhaust to the outside.If you plml to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)The following chart describes an example ot one possible

ductwork instnllation.

DUCT P_ECESEQUIVALENT NUMBERLENGTH x USED

RoofCap 24 Ft. x12Ft.StraightDuct 12Ft. x(6" Round)

RectanguhFto-Round 5Ft. xTransitionAdaptor*

Equivalentlengthsof duct piecesare basedonactualtests andreflect requirementsfor goodventingperformancewith anyventhood.

(1)

(1)

(1)

Total Length

EQUIVALENTLENGTH

24 Ft.

12Ft.

5Ft.

41 Ft.

*IMPORTANT: If a rectangula_to-rotmd transition adaptor is used, the bottom corners of the damper

will ha_e to be cut to fit, usim,._ the tin snips, in order to allow free mo'.ement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example ot one possibleductwork installation.

[DUC_ PIECES

_Wall Cap

(_ 90° Elbow

EQUIVALENT NUMBER EQUIVALENTLENGTH* x USED = LENGTH

40 Ft. x (1) 40 Ft.

3 Ft. x (1)3 Ft.StraightDuct3W' x 10" Rectangular)

10Ft. x (2)

3 Ft.

20Ft.

Equivalent lengths of duct pieces are based on actual tests andreflect requirements for good venting performance with any vent hood.

Total Length = 63 Ft.

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

4


NOTE: If you need to install ducts, note that the total

duct lengti_ of 3¼" x ] O" rectangular or 6" (liameter

round duct should not exceed 140 equivalent feet.

Outside ventilation requires a HOOD EXHAUST DUCT.Read the following careflfllv.

NOTE: It is important that venting be installed usingthe most direct route and with as few elbows as possible.

This ensm'es clear venting of exhaust and helps preventblockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate witha standard 3Vt" x 10" rectangular duct.

If a round duct is required, a rectangula>to-rotmdtransition adaptor must be used. Do not use less thana 6" diameter duct.

Maximum duct length:For satisfiwtorv air movement, the total duct length of

3¼" x ] 0" rectangular or 6" diameter round duct shouldnot exceed 140 equivalent feet,

Elbows, transitions, wall and roof caps, etc.,present additional resistance to airflow and are equivalent

to a section of straight duct which is hinter than theiractual physical size. When calculating the total duct

length, add the equiwdent lengths of all transitions andadaptors plus the length of all straight duct sections.The chart below shows w)u how to calculate total

equivalent ductwork length using the approximate teet

of equiwdent length of some typical ducts.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5 Ft. x ( ) = Ft.Transition Adaptor

Wall Cap 40 Ft. x ( ) = Ft.

C)_ go° Elbow 10 Ft. x ( ) = Ft.

{_ 45° Elbow 5 Ft. x ( ) = Ft.

90° Elbow 25 Ft. x ( ) = Ft.

J 45° Elbow 5Ft. x ( ) = Ft.

Roof Cap 24 Ft. x ( ) = Ft.

Straight Duct 6" Round or 1 Ft. x ( ) = Ft.3W' x 10" Rectangular

Total Ductwork = Ft.

* IMPORTANT: If' a re( tangulal_to-round transilion E(ltfival( nl 1_ ngths of" du(t pieces are bas(d on aclual tests and

adaplor is use(l, the boltonl colners of lhe (]0Jllp( i l-(:_]ect reqtfir( m( nls lk)r good v( nling performan(e with any

_dll have I0 b( {:tit I1) fit, llSillg the till snips, ill V(llt hood.

(}lXiel I(} allo_ flee lllOV(>l)lelll Of' the ([HlllpeF.

5


- SHIPMENT/mNSTALLATmON

® ]If the _it is damaged in shipmenL remr_] the

m_]t to the store im_which it w_s b<mght fi)r repair

ov rep] a ce]_ em_t_

® If the unit is damaged by the customer, repair or

rep];_ceme]_t is the respom_sibi]ity of the cl_stomer.

® ]_f the unit is damaged by the installer (if other

tbam_ the cllstomer), repair or rep]_ceme]_[ mils[

be m:tde by :trram?geme]?[ betweeN? cllstomer am?(]!

im_sta]]er.

PARTS INCLUDED

HARDWARE PACKET

PART QUANTITY

WoodScrews 2(¼" x 2")

ToggleBolts(and 4wing nuts)(¼" x 3")

Self-aligningMachineScrews(¼"-28x 3¼")

Self-aligningMachineScrew(¼"-28 x 2%")

NylonGrommet(for metalcabinets)

3

2 (JVM1790only)

1 (JVM1790only)

2

ExhaustAdaptor 1

Damper 1

MetalScrews 1 black{1_" X I_ 'v) 2 bronze

PowerCordStrap 1(plastic)

You will find the installation hardware contained in

a packet with the trait. Check to make sure you haveall these parts.

NOTE: Some extra parts are included.

PARTS mNCLUDED

ADDITIONAL PARTS

TOP CABINET TENPLATE

NSTALLA?ION

iNSTRUCTIONS

TopCabinetTemplate

RearWall

Template

InstallationInstructions

SeparatelyPackedGreaseFilters

QUANTIFY

1

6


TOOLS YOU WILL NEED

# 1 and#2Phillipsscrewdriver

Tinsnips(forcuttingdamper,if required)

Pencil

Scissors(to cut template,if necessary)

Ruleror tape measure

aightedge

Electricdrill with 3/16",7716,"1½-and%" drill bits

Gloves

Studfinder or Hammer(optional)

Carpentersquare

(optional)

Fillerblocksor scrapwoodpieces,if neededfor top cabinetspacing(usedon recessedbottomcabinet installationsonly)

Saw(saber,holeor keyhole)

L J DuctandmaskingtapeSafetygoggles Level

MOUNTING SPACE

66" ormorefromthe floor

to the top oftheoven

\

Bottomedgeofcabinetneedsto

be30" or morefromthe cooking

surface

Backsplash

NOTES:

• The space between the cabinets must be 30" wideand fl'ee of obst_ uctions.

" If the space between the cabinets is greaterthan 30", a Filler Panel Kit may be used to fill

in the gap between the oven and the cabinets.Your Owner's Manual contains the kit nmnberfoI" VOtlI" model.

" This oven is fin" installation over ranges up to36" wide.

" If vou are going to vent v(mr oven to the outside,see Hood Exhaust Section tot exhaust duct

preparation.

" When installing the oven beneath smooth, flatcabinets, be careful to follow the instructions

on the top cabinet template for power cordclearance.

" The depth of the opening cmmot be more thml13-1/2".

7


I-]PLACEMENT OF THE MOUNTING PLATE

1"_ REMOVING THE OVEN FROMTHE CARTON/REMOVING THEMOUNTING PLATE

_ Remoxe the box containing the installation

instructions, filters, exhaust adaptor, damper

and the small hardware bag,. Do not remoxe

the Styrofoam I_r°tecting, the front of the oxen.

[] Fold back all 4 carton flaps full) against cartonsides. Then careflfllx roll the oxen and carton oxer

onto the top side. T'he oxen should be restino, _ in

the Styrofoam.

Carton

_Pull the carton up and off the oxen.

[]The motmting plate is attached to the back of the

oxen. Remoxe the two screws holding it to the oxen.The plate will be used as the rear wall template andfor mounting the oxen to the wall.

[]Set the oven upri *lit Remoxe and properly discard

plastic bags and Styrofoam.

[Open the oxen door and remoxe the styrofoam

pack from inside the oxen. Remoxe the tape

coxering the turntable hub.

I-_ FINDING THE WALL STUDS

enter_

[] Fim_d t]_e studs, usim_g <me of t]_e fo]]OVTim?g

m e[]] (>ds:

A. Stud timider- a magnetic device whichlocates m_ai]s.

OR

B. [Ise a hammer to tap ]ighdy across die

mom_tim_g sm'Ii_ce to fim_d a solid som_d.This will im_dicate a stud ]ocatiom

_Afler the fi_id the bv]ocatim_g stLld(s), cem_ter

probi_*g the wall with a small m_ailto }h_d theedges o{ the stud. TheN_ place a mark ha]f\_au

betweeN_ the edges. The cel_ter of am_y a(]jaceN_tstuds sholdd be ] 6" or 24" f}'om this mark,

_ Draw a ]im_e dow]_ the cem_ter of the st_ds.

THE OVEN MUST BE CONNECTED TO AT LEAST

ONE WALL STUD.

8


DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position - beneath flat bottomcabinet

Plate position - beneath framed recessedcabinet bottom

Mounting Plate Tabs_gthe Cabinet Bottom

At least 30", up to 3B"

Mounting Plate TabsTouching the BackFrame

II

30"to Cooktop

Plate position - beneath recessed bottomcabinet with front overhang

Mounting Plate withTabs Below CabinetBottom the SameDistance as the Front

g Depth

LL

Ill

30" to Cool<top

Your cabinets may have decorative trim that interferes

with the oven installation. Remove the decorative trim

to install the oven i)roperly and to make it level.

THE OVEN MUST BE LEVEL

ILlse a level to make sure the cabinet bottom is level.

If the cabinets have a fl'ont overhang only, with no

back or side fl'ame, install the mounting plate down

the same distance as the fl'ont overhang depth. This

will kee I) the oven level.

[]Measure the inside depth of the fl'ont overhang.

Draw a horizontal line on the back wall equaldistance below the cabinet bottom as the inside

depth of the fi'ont overhang.

[]For this t):pe of installation with fi'ont overhang only,

align the mounting tabs with this horizontal line, not

touching the cabinet bottom as described in Step D.

9


ALIGNING THE WALL PLATE

Drawa VerticalLineonWall

-<--from CenterofTopCabinet

HoleC

CAUTION: _,,Vearglovesto axoid cutting fingeI5 onsharp edges.

o oo

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

o o o o o oio o o oo ooo

AreaE

H01eD

[]Draw a vertical line on tile wall at tile center of tile30" wide space.

[]Use tile mounting plate as the template for tile rear

wall. Place the mo/mting plate on the wall, makingsure that the tabs are touching the bottom of thecabinet or the level line drawn in Step C for cabinetswith front overhm_g. Line up the notch mid center lineon the mounting plate to the center line on the wall.

_ \._q/ile holding the mounting plate with one hand,draw drcles on the wall at holes A, B, C and D (see

illustration above/actual plate marked with arrows).Four holes must be used for mounting.

[]

NOTE: Holes C and D are inside area E. If neither

C nor D is in a stud, find a stud somewhere in area Eand draw a filil/ circle to line up with the stud. It isimportant to use at least one wood screw mountedfirmly in a stud to support tile weight ot tile oven.

Set the mounting plate aside.

Drill holes on the drcles. If there is a stud, drill a '_A¢_"

hole tot wood screws. For holes that don't line up witha stud, (hill a %" hole fin" toggle bolts.

NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

10


I2-] INSTALLATION TYPES

This oven is designed h>r adaptation to the fi>llowing

3 types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)

(Choose A, B or C)

NOTE: This oven is shiI)ped assembled fin" Outside Top

Exhaust. Select the type of xentilation required for }our

installation and proceed to that section.

OUTSIDE TOP EXHAUST(VERTICAL DUCT)

OUTSIDE BACK EXHAUST(HORIZONTAL DUCT)

1 Adaptorin PlaceforOutsideTopExhaust

_-] RECIRCULATING(NON-VENTED DUCTLESS)

A Charcoal Filter Accessory

Kit is required fin" thenon-vented exhaust. (See yourOwner's Manual fin" the kit

number.)

11


OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top CabinetA3. Install AdapterA4. Mount Oven

A5, A(!just Exhaust AdaptorA6, Connect Ductwork

I-_ ATTACH THE MOUNTINGPLATE TO THE WALL

Attach the plate to the wall using toggle bolts.At least one wood screw IlltlSt be used to attach the

plate to a wall stud.

[]Remove the toggle wings fl'om the bolts.

[]Insert the bolts into the mounting plate throughthe holes designated to go into drDvall andreattach the toggle wings to :Y," onto each bolt.

To use toggle bolts:

Spacingfor TogglesMoreThanWall

-@H,_i*_Th ckness

MountingPlate,

Bolt End

_ Place the mounting plate against the wall andinsert the toggle wings into the holes in the wallto motmt the plate.

NOTE: Betore tightening toggle bolts and woodscre_, make sm'e the tabs on the mounting platetouch the bottom of the cabinet when ptlshedflush against the wall and that the plate is properlycentered trader the cabinet,

CAUTION: Be careflfl to axoid I)inchin'*_ fingers

between the back of the motmting plate and the wall,

_ Tighten all bolts, Pull the plate awax from the wall

to help tighten the bolts,

12


I-_ USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET

You need to drill holes for the top support screws,a hole large enough for the power cord to fit thr(m ,hand a cutout large enough fi_r tile exhaust adaptor.

" Read tile instructions on tile TOP CABINETTEMPLATE.

" Tape it tmderneath the top cabinet.

" Drill the holes, following the instructions on theTOP CABINET TEMPLATE.

CAUTION: Wear safet} goggles when drilling holesin tile cabinet bottom.

ASSEMBLE ANDINSTALL ADAPTOR

Damper

ExhaustAdaptor

_,_.:__ BlowerPlateBac

[] Place tile oven in its ul)right position, with tile topof tile unit tacing up.

_Insert the tabs on each side of the damper into theholes at the inside rear of the adaptor.

_ Attach tile exhaust adaptor to the blower plate withtile two bronze metal screws provided.

Make sure that the damper pivots easily beforemounting oven.

You will need to make a(!iustments to assure properalignment with wmr house exhaust duct atter tileoven is installed'.

I-_ MOUNT THE OVEN

FOIl EASIER INSTAI,IATION AND PERSONAl,

SAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS OVEN.

IMPORTANT: Do not grip or use handleduring installation.

NOTE: If your cabinet is metal, use tile nylongrolUll/et _lro/lnd tile [)()wet" cord hole to l)revent

cutting of tile cord.

NOTE: _4'e recommend using filler blocks if tilecabinet fl'ont hangs below the cabinet bottom shell

IMPORTANT: If filler blocks are not

used, case damage may occur from overtightening screws.

NOTE: When mo/mting tileoven, thread power cord

through hole in bottomof top cabinet. Kee I) it tightthroughout Steps 1-3.Do not pinch cord or liftoven by pulling cord.

_I,ifl oven, tilt itfl_rward, and hookslots at back bottom

edge onto two lowertabs of mountingplate.

/

_Rotate front of o_en

up against cabinet

bottolll.

] , _ throughInsert a self-aligniw* screw , top center

cabinet hole. Temporarily secure the oven b)turning tile screw at least two full turns atter tilethreads haxe ew*aged._, (It will be completel)tightened later.) Be sure to keep power cord tight.Be careful not to pinch the cord, especially whenmom_th_g flush to bottom of cabinet.

13


MOUNT THE OVEN (continued)

CabinetFront

CabinetBottomShelf

Filler Block

T quivalenttoDepthof CabinetRecess

Self-AligningScrew

OvenTop

_]Attach tile oveml to tile top cabim/et.

[] Insert 2 sel6aligning screws(¼"-28 x 3¼") through outertop cabinet holes. Turn twofifll turns on each screw.

[

[]Tighten center

screw completely.

NOTE: Use sel6aligning screw, ¼"-28 x 2:'A", on_[g ItJVM 1790 and self:alignino, _ screws, W'-28 x. /_ ,

on JVM 1490, SCA 1f)00, and SCA 10f) 1.

[] Tightel/ the ol_te_" two sc_'ews to the top of the

ovem (\'_ hi]e tightem/im/g St Ye]ys, h(t](] the ovem/ ira/

I)]ace agai, mist. the wail amld the top cabim/et.)

S /_]]nstall filte_3. See tile Owner Manualgi'ease

packed with tile oxen.

ADJUST THE EXHAUSTADAPTOR

Open the top cabinet and a(!iust the exhaust adaptor

t() connect t() tile hotlse duct.

Damper

[-_ CONNECTING DUCTWORK

HouseDuct

_ Extend tile hotlse dtlct do%vn to connect to

tile exhaust adaptor.

] . , duct tape.Seal exhaust duct ioints using

14


OUTSmDE BACK EXHAUST tHorkontaUD.ct}


B1. Prepare P,ear _4"dl

B2. Attach Mounting Plate to X4'all

B3. Prepare Top Cabinet

B4. A_)just BlowerB5. Mom_t the Oven

F_ PREPARING THE REAR WALLFOR OUTSIDE BACK EXHAUST

_Otl need to Ctlt [lIl l b0 )enino in the rear wall for

outside exhaust.

" Read the instructions on the REAR X4A,I,I,TEMPI ,ATE.

• Tape it to the rear wall, lining up with the holespreviously drilled tot holes A and g in the wallplate.

$ ()it the opening, following the instructions of theREAR X_;_I,I, TEMPI,ATE.

ATTACH THE MOUNTINGPLATE TO THE WALL

i

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate toa wall stud.

_ Remove the toggle wings ti'om the bolts.

_ Insert the bolts into the motmting plate throughthe holes designated to go into (hwwall and reattachthe toggle wings to '_A"onto each l_olt.



MountingPlate

Spacing for Toggles More-,-I-----_i_ Than Wall Thickness

B

Toggle Wings

Bolt End

_ Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: geflwe tightening toggle bolts and wood

scre_, make sure tile tabs on tile motmting plate

touch tile bottom of tile cabinet when pushed flush

against the wall and that the plate is properlycentered under tile cabinet.

CAUTION: Be careflfl to axoid pinching fingersbetween the back of the molmting plate and the wall.

_ Tighten all bolts. Pull the plate awa) from the wall

to help tighten the bolts.

I-_ USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET

You need to drill holes for tile top support screws and

a hole large enom,h for tile power cord to fit throuoh

" Read tile instructions on tile TOP CABINET

TEMPI,ATE.

" Tape it tmderneath tile top cabinet.

" Drill tile holes, following tile instructions on tileTOP CABINET TEMPLATE.

CAUTION: _&ear safety goggles when drilling holesin tile cabinet bottom.

ADAPTING BLOWER FOROUTSIDE BACK EXHAUST

_ Remoxe tile three screws that hold tile blower

plate to tile oxen. Slide blower plate from trader

its retaining, flange, . Remoxe and saxe tile screwthat holds blower motor to oxen.

Retaining _<<i_ -_

Flange _ 5_.__F..___ Blower Plate

.......... Motor[] Carefull) pull out tile blower refit. Tile wires

will extend far enough to allow _ou to a_!justthe blower trait.

BEFORE: Fan Blade

Openings Facing Up

_ Rotate blower trait cotmterclockwise 180 °.

Before Rotation After Rotation

Oven

_ (;entlx tile wires from tilei'ell/ove grooxes.

Reroute tile wires throu_*h grooxes on other sideof the blower trait.

Before Rerouting After Rerouting

Wires Routed Through Right Side Wires Routed Through Left Side

16


_Roll the blower unit 90 ° so that tan blade

oi_enings, are thciw,_ out the back of the o'.en.

BeforeRolling _ .

Backof l'_,_r_Oven

BackofOven

[] I,ocate the two "knockout" plates, on the rearoven panel, near the top of the oven.

Using tin snips, careflflly ctlt the web area fl'omthe two holes side-by-side (that secm'e theknockouts to the oven). Cut all flmr webs on bothrear knockouts; this will allow the ventilation tanairflow to exhaust out the rear of the oven.

CAUTION: Be sure to trim the sharp edges fromthe openings after removing the knockout plates.

Oven Rear Panel

Snipall 4 webson eachknockoutpanelandremovethe metal knockouts

for reara_rflow.

_ Place the blm_er trait back into the o )ening.I

AFTER: Fan

Blade OpeningsFacing Back

EndA

CAUTION: Do not pull or stretch the blowerrefit wiring. Make sure the wires are not pinched.

NOTE: The blower unit exhaust openhlgs shouldmatch exhaust openhlgs on rear of oven.

] Replace the blower plate in the same positionas befi_re with the screws.

BlowerPlateScrews

1_ BlowerPlate/

ii_i-- _1¢ Backof Oven

[] Insert the tabs each side of the intodailll) ei"on

the holes at the inside rear of the adaptor.

Adaptor

_ Attach the exhaust adaptor to the rear of theo'_en b) sliding it into the guides at the topcenter of the back of the oxen.

DamperExhaustAdaptor _ _,_._,,.,..,, (hingeside up)

Slideexhaust _J/,/ _,,- Backof Ovenadaptorinto

Tabs Guideso

Push in securely tmtil it is in the lower lockingtabs. Take care to assure the damper hinge isinstalled so that it is at the top and that thedamper swings fi'eelv.

_ Secm'e the exhaust adaptor to the oven with thetwo bronze metal screws proxided.

17


MOUNT THE OVEN

FOR EASIER INSTAI,I.A_TION AND PERSONAI.

SAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS OVEN.


NOTE: If your (abinet is metal, use the nvlon

grommet around the power cord hole to preventcutting of the cord.

NOTE: We recommend using filler blocks if thecabinet fl'ont hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from overtightening screws.

NOTE: When m()tmtingthe oven, thread powercord through hole inbottom of top cabinet.Kee I) it tight throughoutSteps 1-3. Do not pinchcord or lilt oven by

pulling cord.

[] I,itt oven, tilt itfin'ward, and hookslots at back bottom

edge onto two lowertabs of m()tmting plate.

_ Rotate fi'ont (If oxen l1 I)

against (abinet bottom.

_Insert a sell=aligning screw through top centercabinet hole. Tempora_ilv secm'e the oven byturning the screw at least two full turns alter thethreads have engaged. (It will be completely

tightened later.) Be sure to keep power cord tight.Be careful not to pinch the cord, especially whenmounting flush to bottom of cabinet.

CabinetFront

CabinetBottomShelf

FillerBlock

T quivalentto Depthof CabinetRecess

Self-AligningScrew

OvenTop

_ Attach the oxen to the top cabinet.

_Insert 2 self-aligning screws_I zt(J/('-98 x. ¼ ) through outer

top cabinet holes. Turn twotill turns on each screw.

U

_ Tighten centerscrew completely.

NOTE: Use self-ali.,*ning, screw, ¼"-28 x _2_:' ", on

JVM 1790 and sell=aligning screws, ¼"-28 x 3 V(',on .[VM 1490, SCA 1f)00, and SCA 1f)f}1.

[] Tighten the outer two screws to the top of theoxen. (X._bile tightenin(* screws, hold the oxen

in place against the wall and the top cabinet.)

_ Install grease filters. See the Owner's Manualpacked with the oxen.

18


RECIRCULATmNG tNon-VentedDuctUess)


C1, Attach M(mnting Plate to _'all

C2. Prepare Top Cabinet

C3. Adjust Blower

C4. Mount the Oven

C5. Install Charcoal Filter (not supplied)

I-_ ATTACH THE MOUNTINGPLATE TO THE WALL

Attach the plate to the wall using toggle bolts. Atleast one wood screw Inust be used to attach the

plate to a wall sttld.

[]Remove the toggle wings fl'om the bolts.

_ Insert the bolts into the mounting plate throughthe holes designated to go into drywall andreattach the toggle wings to :Y{' onto each bolt.


Spacingfor TogglesMoreThanWall

+[_-.[.--Th cknessWings

MountingPlate_

if,

Bolt End

_ Place the mounting plate against the wall andinsert the toggle wings into the holes in the wallto inount the plate.

NOTE: Befl)re tightening toggle bolts and woodscre_, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered trader the cabinet.

CAUTION: Be careflfl to axoid I)inchiw*_ fingers,between the back of the motmting plate and the wall.

_ Tighten all bolts. Pull the plate awax from the wallto help tighten the bolts.

USE TOP CAP4NET TEMPLATEFOR PREPARATION OF TOP

You need to drill holes for the top support screws anda hole large enouoh for the power cord to fit throuoh

" Read the instructions on the TOP CABINETTEM PI,ATE.

" Tape it tmderneath the top cabinet.

" Drill the holes, tollowing the instructions on theTOP CABINET TEMPLATE.

CAUTION: _ear satety goggles when drilling holesin the cabinet bottom.

19


ADAPTING BLOWERFOR RECIRCULATION

NOTE: The exhaust adaptor with damper is not

needed fin" recirculating models. You may want to

save them for possible flmu'e use.

[] Remoxe and saxe screws that hold blower plate totile O_ eIl,

_ _ Blower Plate Screws

[]Slide tile blower from trader itsplate i'etaining

flange, and lifi it off, Remoxe and saxe screw thatholds tile blower IllOtOI" to o'_en,

Retaining __

Flange _'__v__"__ BI )wer Plate

3_ Carefully pull out tile blower trait. Tile wireswill extend flu" enough to allow xou to adiust the

blower trait.

• ( o - I &'_4 Roll tile blower rant .)0 so that fan blade o )enim*s-- are fhcing toward the front of the oxen.

BEFORE: Fan Blade

Openings Facing Up_

AFTER: Fan Blade

Openings Facing

NOTE: Make sure wires remain routed in tile

gi'oo_,es of the I/lOtof fI'aIlle,

2O


ADAPTING BLOWER FORRECIRCULATION (continued)

[] Place the blower m/it back ira/to the o )eni m/g.

CAUTION: Do not pull or stretch the hlower _twiring. Make sure tile wires are not pinched°

[] Sectu'e blower unit to o_en with the screw

removed in Step 2. Insert the screw in bottom

right screw hole on the back of the o_en.

_ Replace blower plate with the screws removed in

Step l.

_ Blower Plate Screws

Back of Oven

" _ Blower Motor

Screw

MOUNT THE OVEN

FOR EASIER ]NSTAI,IATION AND PERSONAl,

SAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS OVEN,


NOTE: If your cabinet is metal, use the nvhm

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet fl'ont hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used,

case damage may occur from over tighteningscrews.

NOTE: When mounting

the oven, thread power

cord through hole in

bottom of top cabinet,

Keep it tight throughout

Steps F-3. D() not pinchcord or lili o',en bx

mllino cord.

_ i,if't oven, tilt itflwward, and hookshits at back bottom

edge onto two lowertabs of mounting plate.

_ Rotate front of oven

up against cabinetbottoul,

_lnsert a sell=aligning screw through top center

cabinet hole, Temporarily secure the oven by

turning the screw at least two full turns atier the

threads have engaged, (It will be completely

tightened later,) Be sure to keep power cord tight,

Be careful not to pinch the cord, especially when

mounting flush to bottom of cabinet,

CabinetFront

CabinetBottomShelf

FillerBlock

Equivalentto Depth

f CabinetRecess

Self-AligningScrew

Oven Top

_Attach the oxen to the top cabinet.

21


MOUNT THE OVEN(continued)

_ Insert 9 self-aligning screws_l tt_(V('-28 x. ¼ ) through outer

top cabinet holes. Turn twofllll turns on each screw.

_ Tighten center

screw completely.

NOTE: Use self-aligning screw, Vt"-28 x 2%", onIVM 1790 and self=aligning screws, Vt"-28 x. w ,on .[VM 1490, SCA 1000, and SCA 1001.

[] Tighten the outer two screws to the top of theo;en. (_hile tightenino screws, hold the o;enin place against the wall and the top cabinet.)

_ Install grease filters. See the Owner's Manualpacked with the oxen.

INSTALLING THECHARCOAL FILTER

_ Remove 9 top of ove]i,just above the_ screws o]_

g]'i]] e pam_el, usi m__, ,_ [ ] ] d ] ] d [ _ L screwdriver. Rein oveo]_e sc]'ew om_[he ]ef[ side.

_ ()pe]_ the door.

_ Remove the g]i]]e.

Side--_Screw

JJ

•Screws

_ Insert the filter into the oven as shown,

maneuvering it behind the plastic grille until it fits

squarely into place. It will rest at an angle behind

the plastic grille on two side SUl)port tabs and in

fl'ont of the right rear tab. When proi)erly

installed, the wire mesh of the filter should be

visible fl'om the fl'ont.

_ Replace the grille and the 2 top screws.

[] Close the door and replace left side screw.

Insert mesh-side down

22


BEFORE YOU USE YOUR OVEN

_7_ Make sm'e the ovem_ has beeN_ im_stalledacco]'dim_ to im_st]'l_ctio]_s.

//

%_ Remove all packim_g mate_'ial from tl_e m'e_.

7_ Replace house rinse o]" tm']_ bx'eake]" back o]_.

IllIIIIHII

Read the Ow]_e]"s Mammal.

KEEP INST¢[.[.ATION INSTR[!(}TIONSFOR THE 1,(7)(_I, INSPECTOR'S [!SE.

r_ h_g powei" co]x] im_to a dedicated ]3 to 20 ampelectx'ical outlet.

Insure proper

ground exists/ _before use

23

Printed in Korea

24

In r "m m f

0car

JVM1490,JVM1790,SCA1000y SCA1001

ANTES DE EMPEZARLea estas mstrucciones completa y cnidadosa_enteo

i_strL_cci(mes para e] I_so (]e] im_spector h)ca].

• IMPORTANTE -_:_.._pl..,_to(los los c6(]i_os _ or(]emmzas g_l)er]_ameN_tales.

Nora para el inst_ador = _se_0rese de (]eiarestas im_st_l_cdom_es com_ e] col_Slm_]dor.

* Nora para el consumidor _ (;l_ar(]e estasim_stmcckmes para flmm_ re{erel_cia.

o Nivel de destrezas - i,a im_sta]aci6m_ de este apax_to

reql_iere de destrezas b_sicas de mecSm_ica y e]ectricidad.

o I,a im_sta]aci61_ apropia(_!a es resp(msabi]i(]a(_!(]e] i_sta]a(]or.

@ I,a fhl]a de] pro(]_a:to (]ebido a m_a i_sta]aci61_

LEA CU_DADOSAMENTE.

GUA_DE ESTAS _NST_UCC_ONES.

25

mnstrucciones

hformaci6n generM

Instruceiones de seguridad importantes ................ 27

Requisitos et6ctrieos .............................................. 27

Campana de escape .......................................... 28, 29

Da/!os - Env_o / Instalacidn .................................. 30

Partes h]cluidas ...................................................... 30

Herramientas que necesitar_ .................................. 31

Espacio de montaje ................................................ 31

Guia de instMaci6n paso pot paso

Cdmo colocar el plato de montaje .................... 32-34

(i;6mo remover el phm_ de momm_ie ............ 32

Cdmo emwmm'_r madera s6]ida

era/ ]a pared .................................................. 32

Cdmo determim_r h_ h)c_Iizacid]/

de ]as ph_c_s de h_ pared ............................ 33

()Smo alim/ear la ph_c_ de h_ pared .............. 34

Tipos de instalaeidn .......................................... 3546

_ Escape slq)erior .......................exteYioY. 36-38

C6mo adherir la [:)h_c_ de

mom/t_je _ h_ pared .............................. 36

Preparacid]/ de] gabim/ete siq:)erior . ..... 37

C6mo im/specciom_r si h_ opemci6]/

del regldador de tim es apropiada ...... 37

C6m o mo]/ tar el h orm/o .................. 37, 38

Cdmo _jl_star el adaptador de esc;q:)e ..38

C6mo cm/ectar h_ red de co]/(h_ctos °°-38

_ Escape posterior extemo ...................... 39_-2

C6mo preparar la pared posterior

para el escape posterior exterior ........ 39

C6mo adherir e] plato de

mom/t_je _ ]a pared ........................ 39, 40

Cdmo preparar el _gabim/ete .sl_[)erior..... 40

C6mo adaptar e] caIeihctor [:)ar_

el escape exterh)r posterior . ........... 40, 41

(:(.7/o mol/ta r el h o].m/o........................ 42

de

Recirc_dacidl/ ........................................ 43-46

C6mo adherir e] plato de

mo_/t_je a ]_ pared .............................. 43

C6mo preparer e] g_bi_/ete s_q:)erior...,43

Cdmo adaptar e] ca]efhctor

para ]a recirc_d_cid]/ ...................... 44, 45

C6m o mo]/ tar e] h or_/o .................. 45, 46

()3too ]_/sta]m" e] fi]tro de carb(m]]Ia....45

A_]tes de eomenzar a usar su homo ...................... 47

26

mnstrucciones de

mNSTRUCCmONESDE SEGURIDAD mMPORTANTES

Este i)ro(]{_cto requiere m] tomacorrie]]te el_ctricode tres patas com_ecta(]o a tierra. E] il_sta]ador debe]]evar a cabo m]a im_speccid]_ de co]_timd(]ad a tierraeN_]a/a]a el_ctrica m_tes de comem_zar la im_sta]acidm_[)ara asegurar, que ]a ca.]a tomacorrie]_te est;_.{ o]_ectadaa tierra de mam_era apropiada. Si m) lo est;i, o si eltomacorrieme m_ cump]e coil los reqldsitose]_ctricos i_]dicados (ba.]o ]a seccid]_ REQ[JISITOSEI]_CTR]COS), se deber;i recmTir a m_ t_c_ico

calificado para corregir cualquier deficie_]cia.

PRECAUCBSN:

Para seguridad personal,remneva e! fusible de

la easa o abra el interruptorde eireuito ames decomenzar la instalad6n

para evitar descargase]detricas severas o fatales.

p

PRECAUCI(IN: En pos de ]a seguridad personal,]a superfide de montaje debe ser eapaz de soportar]a earga de] gab_nete, ademfis de] peso adieional(de 63 a 85 libras) de este prodneto, mrs ]as eargasadieionales de1 horno de basra 50 libras o tm peso totalentre 113 y 135 tibras.

PRECAUCI{SN: En pos de la seguridad personal,este prodneto no puede ser iJ_stalado en sistemas de

gabinetes tales eomo los llaaa_ados "isla_s" o "penlnsulas'.Este debe ser montado tanto a m! gal)inete superioreomo a mla pared.

NOTA: Para mqa instalaei6n mrs ffiell yen pos de laseguridad personal, se reeomienda qne dos personasinstalen este prodnem.

IMPOR_I_TE: POR FAVOR, LEACUIDADOSAMENTE. EN POS DE LA SEGURIDADPERSONAL, ESTE APARATO DEBE SERCONECTADO A TIERRA APROPIADAMENTE PARAEVITAR DESCARGAS SEVERAS O FATALES.

t il I /I• i /I

E1 cable el6etrico de este

apaarato estfi equipado conm_ enehufe de tres paros(con eonexidn a fierra),1o enal requiere que elmismo eneaje con m_tomacorriente para tresparas (con conexidn a tierra)de pared pasta m_fizar]a posibilidad dedescargas el&etricas.

AsegOrese deque existe unaconexiOn atierra apropiadaantes del uso

Deberfi haeer que mq t6ertieo califieado inspeceione eltomaeorriente de pared y el ekeuJto para asegurarse deqne el tomacorriente est6 eoneetado a tierra de maneraapropiada.

Donde nsted encnentre tm tomaeorriente estfindar de

dos paras, es m W importante que haga qne el mismo seeambie por mqo de tres patas apropiadamente eoneetadoa fierra, i_stalado por tm eleeMeista ea_fieado.

BAJO NINGUNA CIRCUNSTANCIA NO CORTE,DI_'ORME, O P&2MUEVA NINGUNA DE LNS PATASDI_3L(7ABLE EI_C_[NICO. NO LO USE CON UNA_N_I_]NSI()N FI_;CTRI(_

I,a c]asificacidl_ del prod_,cto es de 120 ratios CA(AC), 611 hertz, ]5 amperMs, y ].70 ki]ovatios. Este

producto debe estar co]_ectado a m_ circ_ito desm_i_fistro de] vo]taje y f_'ec_e_cia apropiados. E]

tamai_o de] a]ambre debe c(mformarse a los reqllisitosdel Natiomd Electric Code o al cddigo local e_ efbcto

para este f_dice de kilovafios. E1 cable e]_ctrico dea]ime]_taci6]] v el ]_terr_q]tor (]ebe_:i_ ]]evarse a _m[oi]/acorrie]/_e i_/Jco co_/ec[ado a [Jerra de ] 5 a

21) ampeIlos, l,a ca.ia de] tomacorrie_te deber;i estar

]oca]iza(]a el/ e] gabi_]ete e]/cJma (]el hor]_o, l,ac;_ja de] tomacorrJe]_te debe set i_]sta]ad;_ pot m]e]ectricista ca]ificado v debe co]_tbrmarse a] Nation,a]

E]ectrica] Code o a] c6digo ]oca] e_ efl_cto.

27

mnsttucciones de instaJacidn

CAMPANA DE ESCAPENOTA: Lea ]as siguientes dos pfiginas solm_lente si plar_ea venNar e] escape hacia el exterior.Si por e] contrario p]m]ea rec_-cular el ake de vue]ta hacia e] saldn, continfie en ]a pfigina 30.

ESCAPE SUPERIOR E×TERNO (EJEMPLO SOLAMENTE}I,a sig_ie_]te mbla describe m_ eiem p]o de m_a posibleim_stal_cidm_de red de co_ductos.

PARTESDEL CONDUCTO

Tapadel techoConductorectode 12pies(redondode 6H)

AdaptadordetransiciOnde rect_nguloa redondo*

LONGITUD NOMERO

EQUWALENTE x USADO

24 pies (1)

12pies (1)

5pies (1)

LaIongitudde las partesdelos conductosequivalentesest_basadaen pruebasrealesy reflejanlosrequisitospara!ograrunabuenaventilaci6nconcualquiercampanade escape.

Longitud total =

LONGITUDEQUIVALENTE

24 pies

12pies

5pies

41 pies

*IMPORTANTE: Si se I_sa m_ adaptador de mmsicid_ de rect_im_gu]o a redom_do, ]as esqldm_s del [o_do

(]el reg_lador de tiros del)er_im_ cortarse para ql_.e e]_c_:ie]_, i_.sm_do ]as t!ieras de corte, [::_ara permitir e]mo','imieN_to libre del reg_lador de tiros.

ESCAPE POSTERIOR EXTERNO (EJEMPLO SOLAMENTE)

La sig_dem_te tabla describe m] eiemplo de m_a posiblei_stalacid]_ de red de c(md_ctos.

[

LONGITUD NOMERO LONG[TUBPARTESDEL CONDUCTO EQUIVALENTE x USADO = EQUIVALENTE

_ Tapade pared 40pies x (1) 40pies

Conductorectode3 pies 3 pies x (1) 3 pies(rectangularde 3W' x 10")

(_ Codode 90° 10pies x (2) 20pies

La!ongitudde las parlesde losconductosequivalentesest_basadaenpruebasrealesy reflejan losrequisitosparaIograrunabuenaventilaci6nconcualquiercampanade escape..

Longitud total = 63 piesNOTA: P_a uI escape posterior sc dcbc te_]cr (:/_id;_do _I _[ine_[" u] csc _pu untrc los usp _cios de los postes dc _ig_ dc h_ p_u:cd,

o 1/par(d deber_ _ set _)repa[" _da el/e/!]!o!]/e!]1o de s// co!/s[['ticcil)!/ d_,i _1/(]o S[ll'i(;iel/_e es}_ _(;io el_tle los }_ostes (]e _ig/ de ]a

}lAte(/ _)arA ACO]]_od _F (_] escAi}e.

28

mnstrucciones de instaJacidn

NOTA: Si rated m_ecesita h_stalar co_(h*ctos, te_g_pem_(tiente que la lo_gimd tot;t] de1 com_(h_cto recm_g_larde 3K/' x ]i0" o el con(;h_cto re(]xmdo de 6" de di_h_etro

no debe sobrepasar 140 pies equivalentes.

l,a ventih_ci6_ extema re(p_iere m_ CONDI/CTO DE(iAMPANA DE ES(iAPE. I,ea lo sig/*ie_te cl_idadosm_e_te.

NOTA: Es importame (p_e ]a ve_ti]acidm_ sea i_sta]adaIlsal/do ]a nmt m_s dh'ecta v col/k_ reel/or camidad de co(los

posible. Esto asegm:_ la vemilad6m_ del escape y :_y_d_ aprevel/h" b]oq{lec, s. Tambi6n, eerd6mse de que el reguladorde tiro pende libremente y nada Moquea los eonduetoso

Conexiones de escape:

l,a cm_pm_a de escape h_ sido diseSada pare el_c_{iar c<mm_ co_(h_cto rectm_gu]ar de 3¼" x ] 0" est;h_dar.

Si im coi?(hlcto redo_?do es _?ecesalJo, se debe/lsar im

adaptador de mmsici&_ de rectang_h_r a redtmdo.No use m'_ eonduem menor de 6" de di_imetroo

Longitud maxima de_ conducto:Pars ]og_r m_ movimie_m_ s_tisfi_ctorio de] _ire, 1_hmgimd total del co_(h_cto recta_gular de 3_//' x ] (1"o el co_(;h_cto redondo de 6" de di_h_etro no debe

sobrepasar 140 pies equivalenteso

Los codos, transiciones, paredes y tapasde techo, etc., presel_ta,_ resiste,_cia _dichmM al

fi_io de sire _ so_ e(p_ivale_tes a m_a secci6_ deco_(h_cto recto e] c_] es m_.s ]argo q_e s_ tam_ff_o ffsicoreal. (h_a_do c;dc_le h_ lol_gimd total del co_(h_cto,

agreg_e ]as ]o_gimdes eq_h'a]e_tes de todas ]asmmsicio_es y _daptadores, m_is h_ hmgimd de todas]as seccio_es de co_d_cto rectas, l,a tab]a re;is ade]a_te

m_estra c6mo puede calc_lar h_ lo_gimd aproximada

de ]a red de co_(;h_ctos _sa_do pies aproximados delol_gimdes eq_iva]e_tes de algmms col_(h_ctos tipicos.

LONGITUD NOMERO LONGITUD

PARTE$ DE CONDUCTO EOUIVALENTE x USADO = EOUIVALENTE

Adaptador de transici_n de 5 pies x ( } = piesrect_ngulo a redondo_

Taps de pared 40 pies x ( ) = pies

(_)_ Codode 90° 10 pies x ( } = pies

Codode 45° 5 pies x ( ) = pies

Codode 90° 25 pies x ( } = pies

J Codode45 ° 5pies x ( } = pies

Taps detecho 24 pies x ( ) = pies

Conducto recto de 6" redondo 1 pies x ( ) = pieso rectangular de 3V_"x 10"

Total red de conductos = pies

,_IMPOR_ANTE: Si s_usa m_adapmdor d_:mmsic%n d_:

29

Jnstrucciones de instalaci6n

- ENViO I

® Si la u_dad se dafia durante el en%o, devueIv_ Ia

mfidad aI aIm_c_m_d(mde Ia adquiri6 parasu

reparac]d]] o reemp]azo.

® Si el cliente da_a la t_idad, ]_ repa_cidm o e]

reemplazo es respo_sabilidad dd diem_te.

®Si el instalador dafia la mlidad (si m_ es el clie_te),la repar_ci6m_ o reemplazo se debe h_cer pot

medio de m_ '_rre_,Jo e_tre el clien_te _ el im_stalador.

PARTES INCLUJDAS

PAQUETE DE ELEMENTOS

PARTE CANTtDAD

Torrfillosdemadera 2(Y4"x 2")

_\ Tornillosbasculantes 4

_/_ (ytuercasdemariposa)(_A"x Y')

Tornillosdem_quinaautoatineables(¼<28x 3Y4")

Tornillosdem_quinaautoatineables(¼<28x 2%")

32(JVM1790S61o)

1(JVM1790SOlo)

Arandetaaislantede 2

nil6n(paragabinetesmet_licos)

Adaptadordel escape 1

Reguladordetiro 1

Tornillosparametal 1 negro(Yd'x Y/') 2 debronce

Abrazaderadelcable Iel_ctrico(pl_stica)

[Jsted em_c(mtrar;_ los e]eme_tos de im_sta]aci(3_ e_

m_ pa(puetejm_to co_ la m_id;_ck h_speccio_e i)_ra

cerciorarse de que tie_e todas ]as partes.

NOTA: Se i_cluye_ algm_as p_rtes adicim_ales.

PARTES INCLUIDAS

PARTES ADICIONALES

PART

[ TOP CABINET TEMPLATE

tN,S3"_LL_TIOI_

INSTFIUCTIONS

Plantillaparael gabinetesuperior

Plantillaparalapared_osterior

Instruccionesde instalaci6n

Filtrosde

grasaempacadospot separado

CANTIDAD

3O

Jnstrucciones de

HERRAMJENTAS QUE NECESJTARA

Dest0rnilladoresdeestrella#1y#2

Tijeras para c0rtar latOn(para c0rtar el reguiad0rde tir0, si es necesari0)

Guantes

L@iz

Tijeras (para c0rtar Japiantiila, si es necesari0)

Sierra (de sane, agujer0, o deoj0 de cerradura)

ecta y cinta m6trica

Taiadro el@ctricocon brocas de3 ** 7 **

Gafasdeseguridad

Escuadra de

carpinter0(0pci0nal)

BJ0quesde reJJeno0pedazos de madera, si son

_ necesarios para rellenar eJ

gabinete (usados solamenteen la instalaci6rl de

gabinetes apoyados)Detector de

postes de viga o un martillo (opcional)

k J Cinta de conductos 0

NiveJ cinta adhesiva protectora

ESPACJO DE MONTAJE

66" o m_s |1

desde el |piso hasta |Japarte |

Elextremodelfondodel gabinete

necesitaestar a30" o m4sa partirde Jasuperficiede

Jaestufa

Protectorposteriordesalpicaduras

N OTAS:

®E1 espario entre los g_]binetes de]be ser de 30"

de ancho y debe estar ]]bre de o]bstxl_cdones.

®Si e] espacio entre los gabinetes es mayor de

BO't m_ "Filler Panel Kit" I)odrfa ser necesariopara reHenar ]as bred]as entre el horno v los

gabinetes. Six Mamma] de] Propietario cont]eneel mimero de 1dr par;_ sl_ modelo.

®Este horno es para ser ]nsmlado por endma deesm{hs hasm 36" de ancho.

®Si Ixsted se dis[)one a venti]ar six horno ]_acia e]exteriox; vex" ]a Seccidn de Campana de Escape

para 1;/ preparaddn de] conducto de escape.

®Cuando se instale el homo debajo de gabinetes

de fo_ldos ]isos y plmms, tenga cuidado de seguircuidadosmnente Ias instrucciones en la plantilla

del gabinete superior para el espacio detolerancia del cable e16ctrico.

®La profmldidad de Ia abertura no puede sersuperior a 13-1/2".

31

mnstrucciones de

C(}MO COLOCAR EL PLATO DE MONTAJE

COMO REMOVER EL HORNODEL EMBALAJE 1 COMOREMOVER EL PLATODE MONTAJE

[] P,eml_eva la ca]a ql_e contiene ]as iasm_cciones deim_stalaci6n, los filtros, el adaptador de escape,

el reg_lador de tiro y la pequeha bolsa con los

elemem_tos de instalaci6n. No reml_eva la espuma

de po]iestix'em_ ql_e px'otege e] fl'e_te de] hoxl_o.

[] P]iegue hacia at__s ]as alas de ]a c;}ja_ I,l_ego,

cl_idadosamente rl_ede e] homo ]]asta que ql_ede

apo_do sobre ]a parte superior. El homo deber5

descam]sar sot)re ]a espm]]a de po]iestireN]o.

[] Ti_'e de ]a c_{]a hacia arriba _ reH_'e]a de] homo.

Caja

_E] plato de mcmt_!je est:_ pegado a ]a pa_'te posted'ion"

de] homo. Reml_ew_ los dos torni]los (p_e ]o

sostienen pegado a] ]_orno. E] plato set5 i*sado

como ]a p]am_ti]]a de ]a pared posterior y para

montar el homo a la pared.

_ Pa]'e e] ]]o]m>. ]_{em_oeva _ desca]'te de ma_e]'a

a[)_'opiada ]as bo]sas I)h_sticas y e] po]iesti_'eno.

_ _kl)ra ]a p_erta de] hondo v rem_teva el paq_tete de

espm_ a de po]i esti re_ o de] i _ te_'i or. Rein _eva ]a

ci_ta adhesiva que cub_'e e] aro giratorio.

32

mnstrucciones de

C. C6MO DETERMJNAR LA LOCAUZACR)N DEL PLATO DE MONTAJEDEBAJO DE SU GABJNETE

Position del pUato - deba]o de gabinetes defondo pUano

Posicibn deU plato - deba]o de gabinetes defondo apoyado en un marco

Las orejillas del plato demontaje tocan el fondodeJgabinete Las orejiiias del plato

de montaje tocan elmarco posterior

L

I I I a_,_

PerIo menos30", hasta36"

II30" hasta la estufa

Posici6n deU plato - debajo de gabinetes defondo apoyado con frente saUiente

Platode montajeconorejillas pordebajodel rondodel gabinetea la mismadistancia

profundidaddel salbote

II

30" hasta ia estufa

Sl*s gabim_etes podr£am_ teller marcos de decoraci6]_

que im_teHieram_ co_ la im_smla_i6m_ del horm_o.P,em_leva los marcos decorativos para im_stalar el horm)

apropiadamem_ te y para hacer q I*e q I*ede m_ive]ado.

EL HORNO DEBE QUEDAR NIVELADO.[°se m_ m_]ve]para cerc]orarse de ql*e e] fimdo de]gabim_ete est', m_ivelado.

Si ]os gabim_etes tieN_em_m_ sa]ie]_te f_xmta] so]ame]_te,

s]m_marco posteric, r o lateral, im_sta]e e] plato dem<mtaie a ]a m]sma distam_c]a de ]a prohmdidadde] sa]]em_te. Este mam_te]_(h5 e] hor]_o _]ve]ado.

[][]

[]

Mida k_ pro[m_didad i_ter]_a (]el fre_te (]el sa]ie]_te.

Trace mm ]f_ea horizo]_ta] e]_ ]a pared posterior a

m]a distancia deb;!jo de] {hi, do de] g_]bh_ete igua]

a ]a prol_m_didad i_ter]_a de] _'e_te sa]ie_te.

Para este tipo de ]_sta]aci6]_ co]_ sa]ie]]te {_'o]_ta]

so]ame_ite, a]h_ee ]as or@Has de moi_ta{ie co]_ ]a ]f_ea

horizoi/ta], si_/ tocar e] {hi/do de] gabi_ete como sedescribi6 e_ e] Paso D.

33

mnstrucciones de

F C6MO AUNEAR EL PLATO DE MONTAJE SOBRE LA PARED

TRACEUNAL[NEAVERTICALENLA

_PARED A PARTIRDELCENTRODELGABINETESUPERIOR

_Agujer0 B

Agujer0C

glmm_tes de proteccidm_

[:>a_;_evitar cortadl_rasem_ S{IS dedos col_ los

extrem os _ilosos.

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 00iO 0 0 0 0 0 0

mAreaE

|

Agujer0D

_ Trace m_a l[m_ea vertical e_ la pared e_ el cem_tro de1

[] llse el plato de mo_taje como la plantilla para Ia pared

posterior; Co]oql_e e] p]ato de mom_t_!ie e_ ]a pared,cercio_indose de que ]as or@Has se el_cl_elm_mtoeando el rondo del gabmete o la _nea marcada enel Paso C para los gabSaetes con sal_entes front,ties.Al_nee la muesca y E'_ea det centro en el plato demontaje con la 15-1ea de centro en la pm°ed°

[] Miemm'as sostie_e el p]ato de m<mmje com_ mm mambo,t_s_ce c_ro_los e_ la pared e_ los agqieros A, B, (} y D(vet la ih_stmcidn a_terior / la placa real esti marcadaco_ flechas). Deben usarse cuatro ag_eros para elnlont_.

[]

NOTA: l,os agqieros C v D va_ e_ el h_te_Jor de1 :irea

E. Si _i el C _1 el D est_i_ en m_ poste de riga,e_c_e_tre m_ poste e_ a]gfi_ otto ]_gar el_ el _irea E vmarque m_ qui_to cfrcu]o para ali_earse con e] poste.Es importm_ te usar por lo menos un tornJ]]o de maderamo_tado firmemente entm poste para apo)_r el peso(]el hondo.

Aparte el plato de montaje°

Per{i)re ag_!ieros e_ los c_ro_los. Si hay m_ poste deriga, per{ore m_ ag_iero de 3/16" pare ]os U)H_i]]os demadem. Pal_ los ag!!ieros que _?o qlledaro_/a]h?eadosco_ el poste de riga, per{i_re m_ ag_jero de 5/8" paralos tor_illos bascu]a_tes.

NOTA: TODA¥_A NO MONTE EL PLATO.

34

mnsttucciones de

TmPOSDE mNSTALACi6N (EscojaA,Bo C}

Este hoH_o est:i disef_do para adaptarse a los sigl_]em_tes

tres tipos de vem_til_cidm_:

A° Escape superior exterior (Condueto vertica!)

B° Escape posterior exterior (Condueto horizontal)

C. Recireulacidn (Sin condueto de ventilacidn)

NOTA: Este hoH_o es em]','iado )a em_samblado p_ra m_

escape slq:_erior exterior. Selecci(me el tipo de ",'e]_til_cid]_

reql_erido para su im_stal_cid]_ } proceda a tal seccidm

ESCAPE SUPERIOR E×TERIOR(CONDUCTO VERTICAL)

ESCAPE POSTERIOR E×TERIOR(CONDUCTO HORIZONTAL}

t El adaptador est4 en su.lugar para el escape

_/superior exterior

C. RECIRCULACION (SINCONDUCTO DE VENTILACION)

I[]_ Kit de accesorios de filtro

de carbo_illa es _ecesario

par_ el sistem_ si_ ve_tilacidm

(Co]_s_]te s_ Mamm] de]

el mimero de] kit.)

35

mnstrucciones de

ESCAPE SUPERmOR EXTERmOR (conauctovmicai}

PERSPECTJVA GENERAL DELA INSTALACION

A1. Como adherir el plato de

mo_taie _ Ia pared

A2. Prepare el g_bh_ete sl_perior

A3. h_stale e] ad%_tadorA4° Mo_te el homo

ASo _iuste el adaptador

de esc_pe [.....

A6o Co_ecte el com_dl_cto

COMO ADHERJR LA PLACADE MONTAJE A LA PARED

Pegue e] plato a ]a pared usm_do los ton_iHos

b:_scl_hmtes. Pot ]o mem)s m_ tor]_iHo de madera debe

set i_sado [_a_:_ [ ,_egar e] [)]ato a] poste de ]a p_red.

[1 Reml_ex'_ ]_s mariposas de] bascl_]_mte de loston_iIIos.

[2 h_serte los toH_illos en el plato de mo_taie a tra_'_s

de los ag_!ieros diseSados p_m_ set im_sertados e_ la

[>ared de mare I)°ster[a....... seca v,t)egue, otra vez ]_s

_?)i_l'i[)os_s de ,_H el/ cada ton)ill(/.

Para usar 10s t0miil0s bascuiantes:

Espaciadores para losbasculantes mayores

_,-I.,-_j-,,_que el ancho de la pared'_las de mariposa

Plato de

montaje

36

ParedExtrem0del tornillo

[] Coloq_e el plato de mo_taie co_tra la pared e

]_serte l_s alas de mariposa e_ los ag_ieros de 1_

pared pa:':_ mop, tar el p]ato.

NOTA: A_tes de apretar los tor_illos b_sc_lm_tes y los

tor_illos de madera, cercidrese de (p_e l_s or@llas e_ el

plato de m(mt_ie toq_e_] el {i_do de1 gabi_ete c_a_do

so_ emp_iadas co_tra la pared y de q_e el plato este_

ce_t_.do apropi_dame_te deb_!io de1 gab]_ete.

PRECAUCION: Tel_ga c_ddado de evitar peHizcar sl*s

dedos e_tre la [x_rte postexJor (]el plato de mo_t:_ie y

_ Apriete todos los toH_illos. Tire de1 pl_m_ el?

direccid_ opuesta a ]a pared para ayudar a apretarlos toH_illos.

Jnstrucciones de

USE LA PLANTJLLA OELGABJNETE SUPERJOFI PARA LAPREPARACK}N DEL GANNETE

Deber_i perfomr ag_ieros para h_s torniHos de

a poyo sl_[)eri ores, i_m__g/!iero sll[i ci e_ tern e_ te

gr_mde par_ ql_e el c_ble e]eSctlJco ql_epa, y m_

recorte 1o sllfidel/temel/te gral?de como pareql_e el ad!aptad!or de escape p/_ed!a set im_trodh_cido.

® I,ea las im_stmccio_es sobre la PIANTII,I,A DEI,GABINETE Si IPERIOR.

® P_gl_e]o deb_jo de] gabim_ete slq_erior.

® T_dadre los ag!_jeros, sig_ieN_do h_s instmcciones e_la P1ANTILLA DE1, GABINETE SilPERIOR.

PRECAUCI()N: Use ga{i_s de segmJdad time, do

perfore los ag_jeros e_ e] flmdo de] gabi_ete.

| ENSAB/IBLAJE E INSTALACIONDEL ADAPTADOF{

ReguJadorde tire

Adaptad0rdeescape

[] Co]oq_e e] hor_m e_ s!* posid6_ vertical, co_ ]aparte s_.perior h_ci_ arribm

[] h_serte ]as or@Has e_ cada ]ado de] reg_]ador de tiroe_ los ag_jeros e_ e] i_terior posterior de] adaptador.

[] Pegue e] adaptador de escape a] plato c_de{i_ctor conlos dos toH_i]]os de bro_ce (p_e ]e

Cercidrese de que el regulador de firo girafficilmente antes de montar el horno°

Deber:i hacer _]ustes par_ _segtm_rse d!e que existe

aIi_ead61_ aproph_d_ co_ el s]stema de co_(_hlctos

de s_ c_sa des[:mets de ]a i_stah_ci6_ de] hormz

| COMO IONTAR EL HORNO

PARA OBTENER UNA INSTAIACI(')N M._S F._CII,

YEN POS DE I,A SE(_UPdlIAD PERSONAI., SE

RECOM:IENDA Qi_E DOS PERSONAS INSTALEN

ESTE HORNO.

IMPORTANTE: No agarre ni use la manijade la puerta durante la instalacidm

NOTA: S] s_ gabi_ete es de metal, _se ]a _mmde]a de

_]]6n _drededor de] c_b]e e]e}ctrico par_ evitar q_e e]mismo sea cortado.

NOTA: e] _*so de b]oq_*es d!e re]]elm

si e] f_'e_te d!e] gabh_ete c_e]ga pot deb_ijo de]

esta_]te de] flmdo de] gabi_ete.

IMPORTANTE: Si no se usan bloques dereUeno, podr_an ocurrir dafios por apretardemasiado los tornillos.

_[ns_r/_ m! tomillo d_ amo di_cacidn a/raxds deI

ag_]cro <:_mr d s_q)erior deI gabincI_. ,\s_ gm'e el

holl_l} /c]/!})l}£ ih!/elH(} _it'_l/do el [ol!}i[Io })l)]" II) III(}//OS

dos vuell.as completas d( sp_ds de q_e las ros<: _s harm

ag_t'_do. (1,u<go ql*ed u'in mmlmem_ apreladas).Cereldrese de mantener el cable el6d.rlco esfirado°

Ter_ga euldado de r_o pelllzcar el cable, especlalmer_te

cuar_do se mor_te al Nvel del for_do del gabmeteo

37

Instrucciones de

COMO MONTAR EL HORNO{continuaci6n}

Frentedel gabinete

Estantedel fondodel gabinete

Bloquede relleno

2 quivalenteala profundidaddel retrocesodel gabinete

Tornillo autoalineable

Parte superior del homo

5 h>erw.... 2 _ornftIos (_ -28 x _ V_ )

al_toaline;_bl_ s a tt'£,('s d( los ag"._i( ros

_ XteI'iol'es S/l})el"iol'es del hol'_to. (}il'e

dos v/_(Itas cI)l/IpIel;{s (// (:;_(];{ _o1!/iI!o.

C_. !/[ t'O CO!/!} )1( [}lI'_/( ll_ ( ,

NOTA: Lse 'I)>t'nillos amoalin( abk s (V_ -2,_ x 2Y_ )

_.]\M/790 y '['ornillos amoati_ d_k s (Y/'-2S x 31A")

_ JVM ! 490, S(]X 1000, } S(]\ 1001.

7_ Aprk t( los dos tornillos exteriores [l _cia I_ ]p _rte

de arriba deI homo. (Miemr _s ap_ieta los {ornillos,

l//aBteH_t el 1/OI"1!O eB SH l_l_a£ ColHla la pared el

gabinete superior;)

[] [_smle los t]lwos d< \'{r el Mam*al d<lgrasa.

(/[t( '_(fl/(f (Oll _.l ho!'llO.

COMO AJUSTAR ELADAPTADOR DE ESCAPE

Abra el gabi_ete superior } a i_ste el adaptador de

escape para co_/ec[arlo a] c(mduc[o de ]a casa.

Reguiador de tiro

COMO CONECTAREL CONDUCTO

Conducto de la casa

[1 Extie_da e] co_ducto de ]a casa hacia paraco_ectar]o co_ e] adaptador de escape.

Selle lasjlmtas del c(mdl_cto de escape itsa_/doc]_?ta ad]?esi'G_ de col?dHctos.

38

mnsttucciones de

[- ESCAPE POSTERmOR EXTERNO tCond.ctohorkontaU!

PERSPECTJVA GENERAL DELA JNSTALACJ6NBlo Prep_re la pred posterior

B2. Pegl_e e] p]_to de mo_m_je

a la pared

B3o Prepare e] gabinete slq)erior

B4, Aj!_ste e] calee_ctorBSo Mom_te e] horl_o

COMO PFIEPAFIAF{ LA PAREDPOSTERIOR PARA EL ESCAPE

Necesita col'tar ima abermra e]_ ]a pared posterior

pare e] escape exterior.

® Lea ]as imlstrL_cci(mes ell la PL_NTH,L¢ PARA I,AP¢RED POSTERIOR.

® Pe}g_e]a co]_ ch_ta adhesiw_ a ]a pared posterior;a]im_e;_m_do]aco_] los ag!!ieros previm_el_te per%mdos[xm_ los ag_!ieros A v B e]_ e] plato de ]a pared.

® Corte ]_ apermra, sig_iem_(]!o ]as im_stmccitmes de ]aPI,ANTH,[,A PARA I,A PARED POSTERIOR.

COMO ADHERJFI EL PLATO DEMONTAJE A LA PARED

39

mnsttucciones de

Para usar los tomillos bascuUantes:

Plato demonta

Espaciadores para los bascuhntes

-.-I--d--- mayores que eJ ancho de JaparedIAlas de mariposa

Extremo del tornillo

[] Co]oql_e el p]ato de momm_je co_m'a ]a pared e

h_serte ]as _das de mariposa e]_ ]os agqieros de

]a pared par:/mommtr e] plato.

NOTA: AN_tes de apretar los tor]_i]]os ]bascl_]am_tes v d

torm_i]]o de mader_/, cerddrese de ql_e ]as or@Has eN_

e] plato de montaie to(p_em_ e] fimdo de] gabim_ete

cl_am_do se empqieN_ com_tra ]a pared y de (p_e e] jp]ato

este} ce]_tmdo apropi_/dame]_te deb_{io de] gabim_ete.

PRECAUCI6N: Tel_ga cuidado de evitar pellizcar sl_s

dedos em_tre ]_/parte posterior de] p]_/to de mom_t_!ie y

]_/ pared.

4_ Ap_iete tod!os los tortoni]los. Tire d!el plato em] d!ireccid]]

o[:mesta a ]a pared [:>m_t ayl_dar a apretar los tor_]]]os.

[-_ USE LA PLANTILLA [3ELGABINETE SUPERIOR PARAPREPARAR EL GABINETE

Necesita per[orar agqieros ]:>:rot los tor,_iHos d!e apo}!_,superiores _. m_ ag/!iero sldicie_teme_te ,grm_de I>a]'a

q ue el cable el 6ctri co q uepa.

® I,ea ]as i,_smlccio,_es sobre ]_/ PI/kNTH,I,A [)El,

(;_B_NETE S[ JPERIOR.

® Pe}gue]_/delx_io de] gabi,_ete superior.

® T_d_/(l!re los agqieros, sig/liendo ]as insmlcciones e,_]a PI./_NTH,I,_ DEI. (;_BINETE S[JPERIOR.

PRECAUCI(')N: [Jse gaf_/s de seg/_rklad cual/do

perfore ]os agqieros e,_ e] fm_do de] g;_bi,_ete.

['_ COMO ADAPTAR EL CALEFACTORPARA EL ESCAPE EXTERIOR

_ Rem_eva y g_/rde ]os tor_i]los q_e sostie_e_ e]

p]_m_ del c_defi/ctor e,_ e] horror. Des]ice e] p]_/to

de] c_deihctor de ab@) de s_ reborde de rete]/ddm

Rem_e_t y g/_arde los tor,_i]]os (p_e sostie]_e]_ e]motor de] ca]efi/ctor el/ e] ]/o11/o.

Reborde de _ IF

delcalefactor

[] Clddadosame]lte tire de] ca]e[i/ctor, lx_s a]ambres

se exte_/der_i_ 1o su[icie,_te como [:/ara permitir]e

que usted _{iuste _a m]Jdad de] c_de{;_ctor.

ANTES: LAS ABERTURAS DE ExtremoB

LA PALETA DEL VENTiLADOR

ESTAN OR_ENTADAS _:-_-

HAOIA ARRIBA

Extreme A _ _.

[]Rote 1;t m_idad 1SO° se,_tidocmm'ario ]_/sel)

agu'as,,! de1 re]@

Antes de la rotaciOn Despubs de la rotaciOn

_rior

del horno Parte posteriordel homo

] S!_aveme]_te los ;dm_l)res de ]asrem_eva 1"_/_) 10]KtS.

Redir!ia los a]ambres a trav(_s de ]as r_mur_/s e_ e]otto ]ado de ]a m_idad de] c_defactor.

Antes de redirigirlos Despu6s de redirigirlos

40

Alambres dirigidos a trav@ del Alambres dirigidos a trav@ delJadoderecho lado izquierdo

Jnstrucciones de

5_ Ruede ]a m_idad de] ca]e[_ctor 90 ° de [orma talque ]as abertm'as de ]a pa]eta de] vem_ti]ador este£m_

orie]_tadas hacia ]a parte posterior (]el hor]_o.

Antes de la r0taciOn Despub.sde la

Pate posteriordel homo

Parte posteriordel homo

[] l,oca]ice los dos jp]atos remo;ib]es eN_ el pam_e]

posterior de] hor]_o, cerca de ]a parte superiordel hondo.

l Ismldo t!ieras, cllidadosame_]te corte el _reade telarafla de los dos ag_ieros ]ado a ]ado (ql_easegmw] los platos removib]es a] horm_o). Corte]as cl_atro te]arai_as el_ ambos p]atos removib]esposter]ores; esto permitir_ (p_e el fil!io de airede] vem]ti]ador escape hacia ]a parte posteriorde] ]]orm]o.PRECAUC][t)N: Cerddrese de recortar los

extremos filosos de las aberturas despu6s deremover los platoso

Parte posterior deB homo Cortecontijeras las

_ uatro teJarafias de

cada paneJ rem0vibby remueva J0sdiscosrem0vibbs de metalpara permitir el fiuj0

de aire posterior

[] Coloql_e la m]idad de1 caleii_ctor de m_evo enla alaert ta'a.

DESPUES: LAS ABERTURAS DE LA PALETA DELVENTILADOR ESTAN ORIENTADAS HACIA ATRAS

Extrem0A

Extreme B _i

PRECAUC]ION: No tire m estire los cables del

calefactoro Cercidrese de que los alambres no

estgn pel]izcadoso

NOTA: Las aberturas del escape del calefactor

deber_in encajar co_] las abertnras de! escape en

la parte posterior det bornoo

] Co]oqlle e] p]ato ca]e[i_ctor ell ]a misma

[:)osic]6]_ como estaba a_tes co]_ los tor]_]]]os.

_ .... Tornillos deJplato cabfact0r_¢ _ Plato calefact0r

_22_-_t _-_-- Parte posterior

__ del h0rn0

[] h_serte 1as ore]i]]as e_ cada ]ado de] reg_lador

de tiro e]_ ]os ag_!]eros e_ e] ]ado i_terior

posterior (]el adaptador.

ptadordeescape

[_}] Ipeglle el aria :_tador de esca :_ea ]a }arte >osterior, I .... _ I I ,de1 hondo desliz_,_dolo ell 1as g_[as e,_ la parte

s_q::_erior ce]_tra] de ]a parte posterior de] hor]_o.

Adaptad0r

de escape

Deslice eladaptad0r deescape en lasguias de laparte posteriordel homo

Regulador de tirogra hacia arriba)

posteriordel homo

_rnillos

6uias0

Eml:mie firmeme_]te hasta que estt) en_ ]as oreiillas

de cierre i_{_riores. Ta_ga c_idado de asegm'arse

de (p_e ]a bisagra de] reg_lador de tiro est5

i_sta]ada de {i_rma q_e est& e]_ ]a parte s_[:>er]or

y q_e e] reg_]ador de tiro g]re ]ibreme_te.

[] Asegm'e el adaptador de escape al hor]_oco_ los dos tor]_]]]os met;i]icos de brtmce

41

[nstrucciones de

MONTAJE DEL HORNO

PARA UNA INSTALACI()N M,{S F,{CH, YEN POS

DE I,A SEGURIDAD PERSONA1,, SE RECOMIENDA

Q{IE DOS PERSONAS ]{NSTALEN ESTE HORNO.

IMPORTANTE: No agarre ni use la manijade la puerta durante la instalacidn.

NOTA: Si sl_ gabh_ete es de metal i_se ]a arm_dek_ d!e

m_ildm_ah'ededor de] cable ekSctrico para evitar ql_e elH?iSH?O se_ col't_do.

NOTA: Recom em_dam os e] I,so de b] oq I*es de rdl en o

si d freN_te de] gabim_ete clm]ga pot deb_io del

estam]te de] _imdo de] gabinete.

IMPORTANTE: Si no se usan bloques derelleno, podr_an oeurrir dafios por apretardemasiado los tornillos.

NOTA: Cua_*do se e]_cuem]x

montando el horm), e]_rosq/m elcable eldctri(o a t_'_ds de1

ag_{jero e_] el [bndo det gd_it_ete

E_ h_s( r_( m_ mrnil[o d( amoalineaci6n a u'_'_ds d(Iag_j_ ro cemrat sup_ riot d(l g_bin( t_. Asegme e1hoH_o t(mpo_almeme gi_ redo el tornillo po_ lome_os dos vueltas eompletas despuds de que lasroscas havan agarrado. (I_uego queda%n tota[mente_pretadas). Cereidrese de mantener el cable el6ctrleoestlradoo Tenga culdado de rm pellizcar el cable,espeeiaImente e_ar_do se mor_te M ravel del for_dodel gablr_ eteo

Frente del gabinete

Estante de[ fond0 de[ gabinete

BI0que de rellen0

T quivaiente a

[a profundidadde[ retroceso

del gabinete

Tomi[[0saut0a[ineables

Parte superior de[ homo

4_J Peg_e el homo a ]a parte superior de] gabi_ete.

E_ [_]serte 2 torni]]os (Y_'-28 x 3Y_")

autoa]i_eab]es a travets de los ag_!ierosexteriores (]el horror. (;,ire dos vueltas

comp]etas e_ cada tor_[Ho.

Apriete e] torni]]o d!el

NOTAs Us( 'Ii>millos mloalineabk_s (_1"-28 x 2%')

e_.JXM1790 } 'Ii_rniJlos m_oalineab/es (gt'-28 x 3Yt")

(_.[VM_490, SC\_000, } SC\100_.

[] Apriete los dos tornillos exteriores hacia la

parte de arriba de] ]]or_o. (Mie_tras aprieta ]ostorl/i]los, ma_?te_?ga el hor]?o e_] sil ]llgar c(mtrala pared y el gabi_ete s_q)erior0

_ h]sta]e los fi]tros de gmsm vet e] Mamma] d!e]

Propietario que "_'ie_e c(m e] ]_oH_o.

mnstrucciones de

RECIRCULACi6N !sinconductode ,entiUaci6.l

PERSPECTJVA GENERALDE LA INSTALAClON

C1. Peg_e e] plato de mom_t_ie

a ]a pared

C2o Prepare e] gabim_ete sl_perior

C3o A._uste e] ca]e{;_ctor

C4. Mo_te el hor_o

C5. Insta]e el }i]tro de carbom_i]]a

(No sm_dmdsm_do)

COMO ADHERJR LA PLACADE MONTAJE A LA PARED

Peg_*e e] plato a ]a pared usm_do los tortoni]los

bascldm_tes, Pot ]o mem_os m_ torm_]]]o de madem debe

set I*sado prow pegar e] plato a] poste de ]a pared.

[1 Reml_eva ]as mariposas de] basodam_te delos tortoni]los.

_ h_serte los torni]]os en e] plato de mont;!ie a tray,sde los. ag_ieros_. .......disefiados [)ara .........setim_sertados em_ ]a

[)ared de mare [)ostei'[a seca _,t)eg_le_ otra vez ]as

mariposas de _" en_ cada torni]]o.

Para usar los tomiHos bascuUantes:

Espaciad0res para los basculantes

+L,_i]r_ayores que el ancho de la paredI '_i

_las de marlposaPlato de

montaje

Extrem0 del tornill0

[] Coloque el plato de mo_m_ie co_m_ la pared ei_serte ]as alas de mariposa en los ag_ieros de ]a

pared para mop, tar e] plato.

NOTA: Antes de apremr los torid]]os bascldm_tes v los

tor_i]]os de madera, cercidrese de q_e ]as or@Has en e]

plato de monmie toque_l el fimdo de] gabh_ete c_;mdo

son emp_]adas co_tra ]a pared y de q_e e] plato este_

center,do apropiadame_te deb_!jo de] gabh_ete.

PRECAUCI(_)N: Te_ga c_ddado de evitar pe]]izcar

s_s dedos entre la parte posterior de] plato de

m o_ mie y la pared.

_ Apriete todos los torni]]os. Tire de] plato e_ direcci6no[:mesta a ]a pared para ay_dar a apretar ]os torni]]os.

USE LA PLANTILLA DEGABINETE SUPERIORPARA LA PREPARACK)NDEL GABINETE

Deber_ per_b_r ag_!ieros pa_ los torni]]os de apoyo

s_periores y m_ agqiero s_{icienteme_te grm_de para

q_e e] cable e]e}ctrico quepa.

® I,ea las i_sm_ccio_es sobre la PI,ANTII,IA [)El,

GABI NETE S[ IPERIOR.

® P_g_e]a deb@_ de] ,gabi_ ere ,su I_eri°r-

® T:dadre mi ag_@ro,, , sig_del_do las i_/str_./ccio_iese_ ]a PI,ANTII,I,A [)El, (;¢BINETE SIJPERIOR.

PRECAUCION: [Jse galti_s de seg_ridad c_a_do

perfore los agueros_.! e_ e] f(mdo de] ,gabi_ete-

43

mnstrucciones de

[-_ C6MO ADAPTAR ELCALEFACTOR PARALA RECJRCULACJ6N

NOTA: El _daptador de escape con cale{i_ctor no

es necesario para los modelos de recircl_l_cidn.

()J_iz_s desee g_rdar]os para posib]es i_sos flmaos.

1_ Reml_eva y g_rde los torni]]os ql_e sostienen e]

plato de] ca]e{i_ctor en e] homo.

_._----Tornillos del plato del calefactor

II

Des]ice e] plato ca]e{i_ctor pot deb_io de su reborde

de retenci6n. P,emueva } guarde los torni]]os quesostienen e] motor de] _a]eii_ctor a] homo.

Plato

Reborde de _calefactor

retencidn

Tornillo del motor++_deJcaJefactor

[] Cuid;_dosamente tire de] c;de{i_(to_: l,os ahm_bresse extender_n 1o su{iciente para permitir]e que

usted _iuste ]a m_idad de] ca]eti_ctor.

orientadas hacia el frente del microondas.

ANTES: LAS ABERTURAS DE LA PALETA DEL

VENTILADOR EST._N ORJENTADAS HACIA ARRIBA

Rue@

DESPUES: LAS ABERTURAS DE LA PALETA DELVENTILADOR ESTAN ORIENTADAS HAC_A ADELANTE

NOTA: Cerd6rese de que h>s ahm_bres permanecen

44

Jnstrucciones de

C()MO ADAPTAR ELCALEFACTOR PARA LARECJRCU LACJ6N Icontinuaci6n/

[] Co]oql_e la m/idad de] cale{i_ctor de m_evoel/ ]a abertm'a_

PR_]CAUCION: No tire m esdre los cables del

calefactor. Cerci6rese de que los alambres no

estgm pdlizcados.

[_ Aseg_lre ]a m/id!ad! d!e] ca]e{k_ctor el/e] hor]/o col/ lostorm/i]]os removidos era/e] Paso 2_ Inserte e] torm/i]]o

era/ el portador de toH/i]]o hqferior derecho era/]aparte poste_i or de] horm/o.

7_ Reemplace e] ca]eli_ctor ]os torl/i]]osp]ato COl/

reH/ovidos el/ e] Paso ].

1_ g_. ....... Tornillosde[

i platocalefactor

--f arte posterior

de[homo__Z-_ _----- Tornii,odel motor

rT_,.f,,,,_ de[caiefactor

MONTAJE DEL HORNO

PARA [/NA INSTAIACION M,4S F,;ff;Ii, Y EN POS DE

I,A SEGURIDAD PERSONAl,, SE RE('.OMIENDA

Q[IE DOS PERSONAS INSTALEN ESTE HORNO.

IMPORTANTE; No agarre ni use la manijade la puerta durante la instalacidn.

NOTA: Si sll gabim/ete es de metal, Ilse ]a aram/deIa dem/i](5]/aIrededor de] cable e]_ctr]co para evitar qlle elmismo sea cortado.

NOTA: Recomel/damos e] Ilso de b]oql_es de re]]eno s]e] _}'el/te de] gabim/ete clm]ga pot deb:{}o de] estaN/tede] {imdo de] gabim/ete_

IMPORTANTE: Si no se usan bloques derelleno, podr_an oeurrir dafios por apretardemasiado los tornillos.

45

_ h]sel'{e /[]] tOl'ni][o de t_ltoalb/eaci6]! _l tl" t'_('s de[agl{iero cemral superior d(t gabine_e. Asegur( el horm>tempor_dmente gira]_do eI tornillo pot to m_]]os dos

wmltas completas despuds de <]_*elas rosc _s haxm

agar* _do. (L_*ego (pmda*fi_] tomlmem( _pr(md _s).Cerei6rese de mantener el cable el6ctrlco estlradoo

Tenga e_ddado de rm pelllzcar el cable, especlalmeme

cuar_do se mome al r_ivel del for_do del gablrmteo

Frente de[ gabinete

Estante del fondo de[ gabinete

Bloque de relleno

T quivaientea la

profundidadde[retrocesode[gabinete

Torniiiosautoalineables

Partesuperiorde[homo

)(g'II( (] ho!'!_o _t I}l ]{)}TH'{( S/IN( l']{Of d(] _{bi]/ele.

Jnstrucciones de

MONTAJE DEL HOF{NO{continuaci6n}

E_ h]serte 2 tor]li]]os (I//L28 x 3_/_")alaoa]im_eab]es a travds de los _g_ierosexteriores sl_periores de] gabim_ete.(;ire dos vl_eltas comp]etas eN_c_(;[atorm_illo.

_priete e] tor]_i]]o delcem?tro comp]etamen?te.

NOTA: [Js_ "['ornilIos amo dil/eabl_ s (_/'-23 x 2_J _)

n,l V [\:1! 790 } "['_H]illos a _o _ti] _( _t_]cs (V*"-28 x 3J/_")

(n ,]VM ! 490, S(;X ! 000, y S(_\ 10(}!.

[] Apriete los dos tor]_i]]os exter]ores hacia la

parte de arriba de] ]]orm_o. (Miem_tr_s aprieta

los tor_i]los, maN_tem_ga e] hor_o em_ sl_ h_gar

co_tra ]a pared y el gab]here s_perior 0

_ l_sta]e los []]tros d!e gr:_sa, vet e] Mamm] de]

Prop]etarh_ (]lie v]e]_e c(m e] hon]o.

COMO INSTALA EL RLTF{ODE CARBONILLA

_ Rem_eva los 2 toH_i]]os e]_ ]a parte superior

dd ]]or_o,justo el_cima de la reiiIIa usa_do m_deston_i]]ador de estre]]m Retire m_ toH_i]]o e_

e] ]_do izquierdo.

_ _kbra ]a [merta.

[] Rem_eva ]a reii]]a.

_ h_serte e] filtro e_ horm} como se m_lestra,

mm_iobrS_do]o detrSs de ]a reii]]a pL_stica h_sm

q_e se _i_ste correctame]/te e_/ s_l ]_lg_/r. Descm_sar_

e_ m_ _i_g_]o detr_is de ]a reii]]a p]_istica e_ (los

]e]_g{?etas ]atera]es de soporte y e_ f_'e]_te de ]a

lel_g£_eta trasem derecha. C4m_do est_i i_stalado

correctame_te, la ma]la de] filtro deberfa estar

visible desde e] f}'e_te.

/lilHliJ

[] Remp]_ce ]_ reii]]_ } los dos ton_i]]os s_q:_eriores.

E_ Cierre ]a puerta } ",'ue]','a a co]ocar e] tor]_i]]o de]

Inserte la malla hacia abajo

46

mnsttucciones de

ANTES DE COMENZAR A USAR SU HORNO

-] Ce_ci_,_ese de _-_l_e el ho_l_o h_ siclo im_st:_L_cloc[e _;_cHel_(_[o COm_ l_s im_st_H(ciol_es.

_ eml_e_';_ to(los los m_te_i_les de emb_l_iec[el hoH_o.

1

--_ Reempl_]ce el f_sil)le de 1_ c_s_] o e]_cie]_dade m_e'_'o el im_te]Tlol){o] _.

IllIIIIIBI

'_ Em_chl_'e el c;_I)le el_ctl"ico e_ im tom_co_T]e_te

(;_!_RDE EST¢S INSTR{!CCIONES P_R_EL _SO DEL _NSPECTOR LOCAL.

47

4%40453 I (06-05JR)

P]'i m_ted i m_Ko]'e;_

Documents

Installation Abovethe CooktopOven...Installation Instructions Abovethe CooktopOven JVM1490,JVM1790,SCAI000,SCAI001 Questions?Call800-GE-CARES(800-432-2737)or visitour _ ebsite at: