instruction manuals

PRODUCT INSTRUCTIONS, INFORMATION & MSDS

RBM HoldBlock™

RBM HoldWash‐HD™

RBM BilgeCoat

RBM Application Set

RBM HydroBlaster

RBM HOLDSOLUTIONS

#101 – 2762 190th Street Surrey, BC V3S 3W6 Canada

+1 604 531‐8333

www.holdsolutions.com

Updated: May 2014

RBM HOLDBLOCK™

A barrier solution for vessels carrying corrosive and/or messy

cargos; such as sulphur, salt, HBI and petcoke.

RBM HoldBlock is removed with RBM HoldWash‐HD.

Recommended Quantities based on a 2 week voyage:

Pail Size: 12" x 12" x 16" Weight: 45 lbs

FEATURES & BENEFITS

Protects metal against corrosive

cargo.

Non harmful to the environment.

Safe to use in occupied/covered areas.

More effective than limewash.

Reduces turnaround times.

Applied by the ship's crew using an RBM Application Set.

Available in 20 litre pail for easy shipping and handling.

USES

Sulphur/Salt‐ Prior to loading to protect against corrosion.

Coal ‐ Prior to loading to assist in cleaning.

DRI ‐ Prior to loading inside the

holds as well as the outer decks,

hatch combings, and

superstructure.

Pitch ‐ prior to loading to assist in

cleanup.

Petcoke ‐ to assist in cleaning

especially around the "tide line"

areas on the bulkheads and helps

preserve paintwork from staining.

RBM HOLDSOLUTIONS


+1 604 531‐8333

Telephone +1 604 531 8333

Fax +1 604 531 9660

Unit 101 – 2762 190 Street Surrey, BC V3S 3W6 Canada

RBM HoldBlock

APPLICATION INSTRUCTIONS . Use low-pressure application equipment to spray onto the surface that needs protection. Only a light spray is needed. If there is liquid running down, too much was used. Allow to dry before loading cargo. HINTS FOR APPLYING Start at the bottom of the bulkheads and work your way up. Hold the nozzle about ½ meter away from the surface. Do not stand in one spot. Side step along the bulkhead, always moving slowly. Apply to the tanktops before leaving the hold. PAINT should be fully cured before applying RBM HoldBlock. Paint that has not cured properly may absorb RBM HoldBlock and cargo residues, making it very difficult to remove. RAIN WATER on the tanktop is okay, but large puddles of water should be mopped up or spread out before applying RBM HoldBlock. RESIDUES from previous cargo and/or Limewash must be removed before applying RBM HoldBlock.

MIXING INSTRUCTIONS . 208-Litre Drums: Premixed. No Mixing Required. 20-Litre Concentrate Pails: 30% HoldBlock Concentrate : 70% Fresh Water (3 pails of Concentrate = 1 drum of Solution) Fill a clean empty drum half way with FRESH water. Add three pails of RBM HoldBlock Concentrate. Mix Well. Top up with water, stirring occasionally.

REMOVAL INSTRUCTIONS . Remove as much remaining loose cargo as possible, as per normal procedures. Rinse down bulkheads with high-pressure water (firehose, etc). Let dry. Use RBM HoldWash to remove all traces of RBM HoldBlock residues. Cleaning procedures may vary depending on type of cargo. If time permits, test various methods in small areas and use most effective method. For more detailed cleaning instructions, please refer to the instruction sheet for RBM HoldWash.

AVERAGE DRUM COVERAGE APPROX

COVERAGE RECOMMENDED QTYS

HANDYMAX PANAMAX

Good Paint and/or Clean Metal Surfaces with Little or No Rust 2200 m2

per drum ½ Drum per hold

¾ Drum per hold

Very Poor Paint and/or Pitted Metal Surfaces with Heavy Rust 1500 m2

per drum ¾ Drum per hold

1 Drum per hold

The above recommendations are based on past experiences. There is no scientific formula to determine the required amount of RBM HoldBlock for each vessel. There are several conditions that can affect the required amount; such as ability, efficiency and past experience of crew, hold conditions, weather conditions, height of application and equipment used.

PRECAUTIONS Although RBM HoldBlock is safe to use, it may cause skin or eye irritation with prolonged contact. As a precaution, wear protective gloves, goggles and a mask. Do not spray directly onto skin or eyes. Avoid prolonged breathing of mist.

FIRST AID MEASURES SKIN: Wash exposed areas with soap and water. EYES: Flush eyes with plenty of water for 15 mins. INHALATION: Remove patient to fresh air. INGESTION: Do not induce vomiting. Give patient a glass of water or milk. GET MEDICAL ATTENTION IF ALLERGIC REACTION OCCURS OR SYMPTOMS PERSIST.

www.holdsolutions.com :: [email protected] RBM HoldSolutions :: Division of Roberts Marine Solutions Ltd

RBM HOLDWASH‐HD™

A versatile all‐purpose marine cleaning solution. It can be used as a

powerful stand‐alone cleaner for oily stains and residues and

removes RBM HoldBlock.

Recommended Quantities:

Jug Size: 10" x 12" x 17" Weight: 41 lbs

FEATURES & BENEFITS

Heavy‐duty hydrocarbon remover.

Can be diluted to suit cleaning needs.


Safe to use in occupied/ covered areas.

Reduces turnaround times.

Easily applied by ship’s crew using an RBM Application Set

USES

Coal

Green Delayed Petcoke

Calcined Petcoke

Sulphur

Salt

General Purpose Cleaner

Removes RBM HoldBlock

RBM HOLDSOLUTIONS


+1 604 531‐8333


Telephone +1 604 531 8333

Fax +1 604 531 9660


RBM HoldWash-HD

APPLICATION INSTRUCTIONS HEAVY-DUTY CLEANER Instructions for cleaning oily residues (Coal, Petcoke, Concentrates, etc), whether or not RBM HoldBlock was used as a barrier before loading. 1. After discharge, remove as much remaining cargo as possible, as

per normal procedures. 2. Do NOT wet surface before applying HoldWash-HD. 3. Mix 4 pails of RBM HoldWash-HD Concentrate with approx. 120

litres of fresh water, as per Mixing Instructions. 4. Apply HoldWash-HD liberally to affected areas with a low-pressure

application system. 5. Allow to soak for about 15 minutes. 6. Use a firehose or high-pressure washer to clean the area. Use the

highest pressure possible. Seawater OK. 7. Some brushing and/or scrubbing may be required for stains. 8. If second application is required, wait for surface to dry before

applying again. BARRIER REMOVAL Instructions for removing RBM HoldBlock, after discharging non-oily cargos (Sulphur, Salt, etc) 1. After discharge, remove as much remaining cargo as possible, as

per normal procedures. 2. Rinse down bulkheads with high-pressure water (firehose, etc). 3. Let dry. 4. Mix 3 pails of RBM HoldWash-HD Concentrate with approx. 140

litres of fresh water, as per Mixing Instructions. 5. Apply HoldWash-HD liberally to affected areas with a low-pressure

application system. 6. Allow to soak for about 15 minutes. 7. Use a firehose or high-pressure washer to clean the area. Use the

highest pressure possible. Seawater OK. GENERAL CLEANING Instructions for general hold maintenance and light-duty cleaning (engine room, crew’s locker, kitchen, crane pedestals, etc.) 1. Mix 2 pails of RBM HoldWash-HD Concentrate with approx. 160

litres of fresh water, as per Mixing Instructions. For small areas, simply dilute 1:4 in any type of container.

2. Apply HoldWash-HD liberally to affected areas. 3. Allow to soak for about 15 minutes. 4. Rinse clean with water.

MIXING INSTRUCTIONS Fill a clean empty drum half way with FRESH water. Add required pails of RBM HoldWash-HD Concentrate (see dilution rates). Mix Well. Top up with water, stirring occasionally.

DILUTION RATES Heavy-Duty Cleaner 1:1.5 4 Pails / Drum (80 ltrs:120 ltrs water) Coal, Petcoke, Concentrates, etc Barrier Remover 1:2 3 Pails / Drum (60 ltrs:140 ltrs water) Removal of RBM HoldBlock General Cleaning 1:4 2 Pails / Drum (40 ltrs:160 ltrs water) Hold Maintenance, Engine Room, etc

HOW LONG TO SOAK? 30 minutes is only the suggested time. More time may be required for heavier residues. Determine the size of sections to clean and the soaking time by the current weather conditions. Clean small section in warm climates. In cooler temperatures, when drying time can be longer, clean larger sections. PRECAUTIONS Although RBM HoldWash-HD is safe to use, it may cause skin or eye irritation with prolonged contact. As a precaution, wear protective gloves, goggles and a mask. Do not spray directly onto skin or eyes. Avoid prolonged breathing of mist.

www.holdsolutions.com :: [email protected] RBM HoldSolutions :: Division of Roberts Marine Solutions Ltd

RBM BILGECOAT

An alkaline solution used for the bilge lines and bilge wells during

sulphur voyages. It acts as a neutralizing agent.

Recommended Quantities:

One jug of RBM BilgeCoat concentrate, when mixed with water,

makes 200 litres of BilgeCoat solution.

Approx. 15 litres of BilgeCoat solution is poured down each

sounding pipe, in each hold, prior to loading sulphur and after each

flushing of the bilges during the voyage.

RBM recommends 1 Jug per hold, per week.

Jug Size: 9.5" x 11.5" x 15" Weight: 41 lbs

FEATURES & BENEFITS

Bilge protection against acidic

water.


Easier to use and safer than

caustic soda flakes.

RBM HOLDSOLUTIONS


+1 604 531‐8333


Telephone +1 604 531 8333

Fax +1 604 531 9660


www.holdsolutions.com :: [email protected]

RBM HoldSolutions :: Division of Roberts Marine Solutions Ltd

RBM BilgeCoat

MIXING INSTRUCTIONS .

Use a clean empty container. Add 1 jug of BilgeCoat Concentrate. Add 180 litres of fresh water to make

BilgeCoat solution.

APPLICATION INSTRUCTIONS .

Pour 15 to 20 litres of BilgeCoat Solution directly into each hold sounding pipe from on deck.

Replenish each time after the bilge water is pumped out.

PRECAUTIONS Avoid contact with skin and eyes. Avoid breathing mist and vapors. Always wear protective gloves, goggles and masks. Keep away from oxidizers, acids and metallic powders. Refer to MSDS for more information.

FIRST AID MEASURES SKIN: Wash exposed areas with water. EYES: Flush eyes with plenty of water for 20 mins. INHALATION: Remove patient to fresh air. INGESTION: Do not induce vomiting. Give patient a glass of water or milk. GET MEDICAL ATTENTION IF ALLERGIC REACTION OCCURS OR SYMPTOMS PERSIST. NOT SAFE FOR HUMAN CONSUMPTION.

RBM APPLICATION SET

Specifically designed equipment for low‐pressure application of RBM

HoldSolutions product line.

All of our Application Sets come with an instructional DVD. The

application process is easily accomplished with 2‐3 crew members. Pump

and drum stay on deck for easy access.

Our equipment is of the highest quality workmanship and will work for

many years with regular maintenance and servicing. We have repairs kits

if required.

Please note that these pumps cannot be used for applying acids or other

highly corrosive chemicals as the diaphragms and internal workings of the

pump are not designed to withstand these solutions.

Application Set Box Size: 24" x 18" x 17" Weight: 61 lbs

PowerWand Box Size: 96" x 7" x 3" Weight: 10 lbs

FEATURES & BENEFITS

Specifically designed for low‐

pressure application.

Compact & lightweight for easy

storage and handling.

Powered by ship's compressed

air.

RBM HOLDSOLUTIONS


+1 604 531‐8333


RBM Application SetRBM Application SetCONTENTS

RBM Application Pump

AS-A036

Outlet Hose (150 Feet) Suction Hose

Air Operation Hose Wand Hose (40 Feet)

$1,090.00 $40.00 $60.00

$120.00 $40.00

AS-P515

Support Belt$20.00AS-XW-601

A/S Spray Kit

AS-H38-150

AS-H38-003

RBM PowerWand - 36’ (Packaged Separately)

$595.00

AS-W606

AS-H34-010

AS-H38-040

Nozzle PackageAS-XW-600

A/S Repair Kit

$90.00

www.holdsolutions.com+1-604-531-8333 (24 hrs)

ALWAYS USE HEAVING LINE Never use the hoses to raise or lower the PowerWand. Always lower the wand with the tip facing upwards.

FLUSH PUMP & HOSES AFTER USE 1. Pump FRESH water through system to flush pump and hoses after each use. 2. Drain as much water as possible from hoses before putting away in storage.

WIPE DOWN POWERWAND AFTER USE 1. Disassemble the PowerWand by removing sections from each other. 2. Spray RBM HoldWash-HD (10:1 mixture) onto each PowerWand section. (If HoldWash-HD not available, use a mild degreaser instead.) 3. Let sit for one minute, then wipe clean. 4. If inside of tubes require cleaning, spray HoldWash-HD (10:1) inside the tubes. 5. Insert a rag into each section and push through with a bamboo pole.

STORAGE INSTRUCTIONS Store in a heated storage locker. Never store in freezing conditions.

CARE & MAINTENANCE

TROUBLESHOOTINGPROBLEM: NO SUCTIONCAUSE: Air in Pump and/or HosesSOLUTION: Reprime the PumpINSTRUCTIONS: Before repriming, check to make sure the suction hose is submersed in the liquid. To reprime, remove suction hose from liquid and let pump run until mostly empty. Turn pump off. Protect eyes and disconnect outlet hose. Insert suction hose into liquid. Stand away from pump. Turn on pump for about 2 seconds, or until liquid fills up suction hose. Reconnect outlet hose to pump. Continue using.

PROBLEM: LOW PRESSURECAUSE: Regulator Turned Down / Compressor Too LowSOLUTION: Adjust Regulator / Increase Outflow at CompressorINSTRUCTIONS: While pump is operating, adjust regulator to between 90 - 100 psi. If pressure is still low, then the outflow must be increased from the engine room. If more pressure is not available, then try priming the pump first before attaching the outlet hose.

PROBLEM: LEAKING FLUID (at Suction Inlet)CAUSE: Washer Missing / Connection is not TightSOLUTION: Replace Washer / Tighten Connection

PROBLEM: LEAKING AIR (at Back of Pump)CAUSE: Bolts are LooseSOLUTION: Tighten BoltsINSTRUCTIONS: Use a 1/2” wrench to tighten the silver bolts on diaphragm cover. Be careful to not over-tighten, which can cause the plastic to crack.

PROBLEM: PUMP IS VERY LOUDCAUSE: Broken Muffler cause by Accidental Contact or Over-TighteningSOLUTION: Use Pump without Muffler or Order New MufflerINSTRUCTIONS: Pump will operate normally without a muffler, but will be very loud. A new muffler can be ordered from RBM HoldSolutions if required.

AS-XW-610Wand Tip (1)

AS-N40-050Fan-Spray Nozzle (2)

AS-N78-026Cone-Jet Nozzles (2)

ALSO AVAILABLE

AS-XP730 AS-XP740$295.00 $125.00Pump & Hose Fittings, Air Filter,

Regulator & Diaphragm Repair KitWand Tip, 4 Nozzles, Support Belt,

5 Splash Goggles & 10 Particle Masks

Protective Clothing KitAS-PC101 $295.00

6 Splash Goggles, 6 Particle Masks,6 Nitrile Gloves & 6 Hooded Coveralls

1. PREPARATIONUnpack the equipment and identify all parts to be assembled. Unroll all hoses. Find a solid and sturdy surface for the pump on deck near the cargo hold where it will be used.

In addition to the items supplied, you will also need an Air Hose, a Heaving Line (for lowering the PowerWand), a clean bucket of fresh water (for flushing pump and hoses after use) and some twine (for securing hoses).

4. CONNECT AIR HOSEConnect the Air Operation Hose (included with RBM Application Set) to the pump.

3. INSERT SUCTION HOSEInsert the opposite end into the drum opening. If opening is too small, simply remove the suction filter. To prevent curling, tie the hose to a stick.

2. CONNECT SUCTION HOSEConnect blue suction hose (10 feet) to pump. Make sure connection is hand-tight. Do NOT use a wrench.

5. CONNECT AIR HOSESConnect the Air Operation Hose to the Ship’s air hose. If the connections are not compatible, use the hosebarbs (supplied with the Air Operation Hose) instead.

8. FEED WAND HOSEFeed the Wand Hose through the inside of the PowerWand. Do NOT extend the PowerWand yet. Twist gently if blocked.

7. CONNECT HOSESConnect the Outlet Hose (150 feet) to the Wand Hose (40 feet). Turn fluid valve OFF.

6. CONNECT OUTLET HOSEConnect the Outlet Hose (150 feet) to the pump. Use twine or rope to secure the Outlet Hose to a solid fixture, to relieve pressure on the pump connections.

9. CONNECT WAND TIPConnect the Wand Tip to the Wand Hose. Set the Wand Tip into the top of the PowerWand and tighten the nut by hand. Do NOT use a wrench.

10. CONNECT NOZZLEConnect the white Fan-Spray Nozzle to apply RBM HoldBlock, or connect the brass adjustable Cone-Jet Nozzle to apply RBM HoldWash-HD. Turn clockwise for a fine mist, or counter-clockwise for jet spray.

11. LOWER WAND INTO HOLDAlways use a heaving line. Never use the hoses to raise or lower the wand. Always make sure tip is facing upwards.

12. TURN ON AIR SUPPLYOpen ship source and turn air valve ON. Test the pump to ensure there are no air or fluid leaks.

13. ADJUST PRESSUREAdjust the air pressure gauge to between 90 and 100 psi, if necessary. If pressure does not increase at the pump, then increase the air pressure supply from the engine room.

Ship’sAir Hose

AirOperation

Hose

Air Valve

Fluid Valve

14. ENTER CARGO HOLDThree crew members are recommended for using the RBM Application Set. One crew should remain on deck to monitor the pump. One crew should hold the hoses and operate the fluid valve inside the cargo hold. The last crew member should control the direction of spray with the PowerWand.

15. BEGIN SPRAYINGExtend PowerWand to desired height. Turn fluid valve ON to begin spraying.

A heaving line can be used to support the weight of the wand from above.

HoldBlock

HoldWash

RBM HYDROBLASTER

A very powerful cleaning tool when used in conjunction with HoldWash‐

HD.

Combines water and compressed air to create a powerful jet of water for

excellent cleaning results.

It can provide a "jet" of water to over 100' (30 m), with efficient ship's

compressor and is excellent at removing cargo residues, rust and scale

and loose paint.

HydroBlaster Box Size: 49" x 9" x 9" Weight: 45 lbs

Air Hose Size: 30" x 30" x 6" Weight: 64 lbs

FEATURES & BENEFITS

Adjustable control valve.

Easy to set up and use.

Solid 3 legged stand for stability.

Operational by one man.

Kit comes complete with gun,

stand and 150' / 1" ID Air hose.

SPECIFICATIONS

WATER CONSUMPTION 485 ltr/minute (110 gal/minute)

WATER PRESSURE 85‐90 PSI (6 KG/CM2)

AIR CONSUMPTION 71 cfm (2m3/Minute)

AIR PRESSURE 100‐120 PSI (7‐8 KG/CM2)

WATER HOSE 2" (51mm) or 2.5" (64mm)

RBM HOLDSOLUTIONS


+1 604 531‐8333


RBM HydroBlasterRBM HydroBlaster

CONTENTS

AS-M485

H/B Air HoseAS-H100-150

HydroBlaster Gun AS-M485G

HydroBlaster StandAS-M485S

Fire Hose Couplers


AS-M451C51mm (2.0”)

AS-M464C64mm (2.5”)

1. ATTACH GUN TO STANDErect the HydroBlaster stand, locking the legs to ensure it is stable. Attach the gun to the stand and use the locking pin to secure the gun in place.

2. CONNECT FIRE HOSESelect a fire hose coupler (51 or 64mm) to match the inside dimension of the fire hose to be used. Connect one end of the fire hose to the ship’s water supply and the other end to the HydroBlaster gun.

3. CONNECT AIR HOSEAlways blow out the air hose before using to remove particles. Connect one end of the air hose to the ship’s air supply and the other end to the HydroBlaster gun. Turn the air valve to the OFF position.

4. TURN ON WATER & AIRWhile holding the gun steady, slowly turn on the water supply. Once the water supply is steady, slowly open the air valve. Adjust until a hard-hitting jet is obtained. Too much air flow will cause the jet stream to break up.


Recommended Water Pressure 6 kg / cm2 85 psiRecommended Air Pressure 7 kg / cm2 100 psiEstimated Air Consumption 2 m3 / min 71 cfmRecoil 10/18 kg 24/40 lbsWeight of Gun & Stand 15 kg 33 lbsWeight of Gun 5.6 kg 12 lbsLength of Gun 74 cm 24"Length of Stand 140 cm 45"

SPECIFICATIONS

1

SDS

Safety Data Sheet

SECTION I: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Material Name / Identifier - RBM HoldBlock Synonyms - Paraffin Wax Emulsion Product CAS Number - 8002-74-2

Application - Surface-block barrier, used primarily as barrier protection on marine vessels

Supplier’s Name: - RBM HoldSolutions (A division of Roberts Marine Solutions Ltd.) Address: - Unit 101 – 2762 190th Street City & Province: - Surrey, British Columbia, Canada V3S 3W6 Telephone (Including Emergency) - +1 604 531 - 8333 E-mail (Including Emergency) - [email protected]

SECTION II: HAZARDS IDENTIFICATION

This substance is not classified according to UN / GHS guidelines

GHS labeling requirements: None

Other hazards: Liquid May cause irritation to eyes and skin on prolonged contact Vapour May cause irritation of respiratory tract

SECTION lII: COMPOSITION / INFORMATION ON INGREDIENTS

Generic name: Wax emulsion, corrosion preventative CAS number (Paraffinic component): 8002-74-2 EINECS number (Paraffinic component): 232-315-6 Chemical characterization: Preparation; Emulsion of paraffin wax in water

SECTION IV: FIRST AID MEASURES

Inhalation: Take person to fresh air Eye contact: Flush eye immediately with cold water. If irritation continues seek medical attention Skin contact: After contact with product remove soaked clothing and wash the skin with water and soap When swallowed: When swallowed seek medical attention. Not considered toxic. Do not induce vomiting.

SECTION V: FIRE FIGHTING MEASURES

Flammability of the product: Not flammable Products of combustion: Carbon oxides (CO1 / CO2 )

Fire-fighting Media and Instructions:

Small fire: Dry chemical powder, carbon dioxide, sand. Large fire: Water spray, fog or foam Protective equipment (fire): Approved / certified respirator or equivalent Specific hazards: Water evaporates out of the product. The remaining hydrocarbon oil is flammable. In case of incomplete combustion irritant vapours, smoke, soot and carbon monoxide (CO) may be formed. Additional information: Apply cold water in order to cool containers exposed to danger.

SECTION VI: ACCIDENTAL RELEASE MEASURES

Small spill and leak: Dilute with water and mop up or absorb with inert dry material and place in appropriate waste disposal container Large spill and leak: Absorb with inert material and place in suitable container. Dispose in accordance with regulations.

SECTION VII: HANDLING AND STORAGE

Handling:

Hints on safe handling: No special measures if used correctly Hints for protection against fire and explosion: Avoid formation of product mist

Storage:

Requirements for storage rooms and containers: Store in bunded area large enough to contain total spillage Information on storage together with other products: Do not store together with oxidizing agents and food

Additional information: Store product at room temperature. Keep from freezing. Protect against high temperatures.

mailto:[email protected]

2

SECTION VIII: EXPOSURE CONTROL / PERSONAL PROTECTION

Exposure limit (Fumes): NIOSH / ACGIH (United States, 2002) TWA 2 mg/m3

Personal protective Equipment:

Hand protection: Waterproof gloves Eye protection: Safety goggles Body protection: Protective clothing

SECTION IX: PHYSICAL AND CHEMICAL PROPERTIES

Appearance: White liquid Odour: Practically odourless Odour treshold: Not available pH: 8 – 10 Congealing point: Not applicable Initial boiling point: >1000 C (OECD 103) Flash point (Open cup): Not available Evaporation rate: Not available Flammability: Not classified

Lower Flammability limit: Not available Vapour pressure: Not available Vapour density: Not available Density at 250 C: 0.97 kg/L Solubility in water (200 C): Soluble (Miscible) Partition co-efficient (O/W): Not available Auto-ignition temperature: Not available De-composition temperature: Not available Viscosity: Not available

SECTION X: STABILITY AND REACTIVITY

Conditions to avoid: Temperatures below 50 C and above 350 C as this may cause separation of emulsion into components Materials to avoid: Strong acids and alkalis Hazardous de-composition products: Carbon and nitrogen oxides

SECTION XI: TOXICOLOGICAL INFORMATION

No information available. Products of similar compositions did not induce toxic effects.

SECTION XII: ECOLOGICAL INFORMATION

No information available. As a precaution keep away from waterways, sewers, drains, basements and confined spaces.

SECTION XIII: DISPOSAL CONSIDERATIONS

Waste information: Waste must be disposed of in accordance with Federal, State, and Local environment control

regulations. European waste catalogue (EWC) recommends disposal according to EWC 12 01 12 (Spent waxes and fats) or EWC 12 03 02 (Steam degreasing wastes). The product is suited to be recycled in authorized plants.

SECTION XIV: TRANSPORTATION INFORMATION

UN Number: Not classified Product is not classified under any of the following: DOT (United States), TDG (Canada), IMDG, IATA / ICAO

The product is not classified according to EU regulations

SECTION XVI: ADDITIONAL INFORMATION

Under reference to MEPC 63/23/Add. 1, Annex 24 Resolution MEPC 219(63) as adopted on March 02, 2012; RBM HoldSolutions declares herewith that the hold cleaning product referred to as RBM HoldBlock and marketed by RBM HoldSolutions, the nature of which is covered in this SDS meets the criteria as non-harmful to the marine environment as described under section 1.7.5 of above resolution. This statement is not valid for any other solutions or chemicals, which may be put on the market with identical or similar product name. The names of RBM HoldSolutions and RBM HoldBlock must be mentioned on the product label and in the Safety Data Sheet. Although the information contained herein is presented in good faith and to the best knowledge and experience of supplier / distributor, it is made without any warranty or guarantee whatsoever.

Prepared by: Contact details: Date issued: Replaces:

RBM HoldSolutions Phone: +1 604 531 – 8333 Email: [email protected] December 13, 2012 October 01, 2006

SECTION XV: REGULATORY INFORMATION

RBM HoldSolutions101 - 2762 190th St

Surrey, BC, Canada V3S 3W6Phone: 604-531-8333

RBM HoldWash HD Not available.Page 1 of 8MSDS Preparation Date (mm/dd/yyyy): 11/19/2013

MATERIAL SAFETY DATA SHEET

SECTION 1 - IDENTIFICATION

Product identifier RBM HoldWash HD:

N/Av:Product Code(s)

Heavy duty degreasing syrup:Product Use

:Chemical Family Mixture.

Refer to SupplierRBM Holdsolutions

Supplier’s name and address: Manufacturer’s name and address:

Unit 101-2762 190th StreetSurrey, British Columbia, CanadaV3S 3W6

(604) 531-8333:Information Telephone #

Refer to supplier:24 Hr. Emergency Tel #

WHMIS information: This product is a WHMIS Controlled Product. It meets one or more of the criteria for a controlled product provided in Part IV of the Canadian Controlled Products Regulations (CPR). WHMIS classification: Class B3 (Combustible Liquids) Class D2B (Materials Causing Other Toxic Effects, Toxic Material)

OSHA: This material is classified as hazardous under OSHA regulations (29CFR 1910.1200). Hazardous classification: Acute Health Hazard Flammable liquid Chronic Health Hazard

:Classification

SECTION 2 - HAZARDS IDENTIFICATION

Emergency Overview Light gold liquid. Peach-like odour.Warning! Combustible liquid and vapour. Causes eye and skin irritation. Inhalation may cause respiratory irritation and central nervous system depression. May be harmful or fatal if swallowed. Aspiration may occur during swallowing or vomiting, resulting in lung injury. May cause skin sensitization.

:

POTENTIAL HEALTH EFFECTS:

:

Signs and symptoms of short-term (acute) exposure

May cause respiratory irritation. May cause headache, nausea, dizziness and other symptoms of central nervous system depression.

Inhalation

:Skin May cause moderate skin irritation.

:Eyes May cause mild to moderate irritation.

May cause irritation to the mouth, throat and stomach. May be an aspiration hazard. Aspiration into the lungs during swallowing or subsequent vomiting may cause chemical pneumonitis, which can be fatal.

Ingestion :

Prolonged or repeated skin contact may cause defatting and drying resulting in irritation and possible dermatitis.

Effects of long-term (chronic) exposure

:

See TOXICOLOGICAL INFORMATION, Section 11.:Carcinogenic status

Additional health hazards : Skin sensitizer. See TOXICOLOGICAL INFORMATION, Section 11.

See ECOLOGICAL INFORMATION, Section 12.:

Potential environmental effects




SECTION 3 - COMPOSITION/INFORMATION ON INGREDIENTS

Ingredients CAS # Wt.%

Distillates (petroleum), hydrotreated light 10.00 - 30.0064742-47-8

d-Limonene 5.00 - 10.005989-27-5

Monoethanolamine 1.00 - 5.00141-43-5

Move to fresh air. If breathing has stopped, give artificial respiration. If breathing is difficult, give oxygen by qualified medical personnel only. Get medical attention.

:Inhalation

SECTION 4 - FIRST AID MEASURES

Wash affected areas with soap and water. Remove contaminated clothing and shoes. Obtain medical attention if irritation persists. Wash contaminated clothing before reuse.

Skin contact :

Flush with large amounts of water for 15 minutes. Get medical attention if irritation develops and persists.

Eye contact :

Ingestion Do NOT induce vomiting. If vomiting occurs spontaneously, keep victim's head lowered (forward) to reduce the risk of aspiration. Never give anything by mouth to an unconscious person. Get medical attention immediately.

:

Treat symptomatically. This product is a CNS depressant.:Notes For Physician

Fire hazards/conditions of flammability

SECTION 5 - FIRE FIGHTING MEASURES

Combustible liquid and vapour. Vapours are heavier than air and may spread along floors. Vapour can travel considerable distance and flashback to a source of ignition. Closed containers may rupture if exposed to excess heat or flame due to a build-up of internal pressure. Do not pressurize, cut, heat or weld empty containers. Empty containers retain residue (liquid and/or vapour) and can be dangerous.

:

Flammability classification (OSHA 29 CFR 1910.1200)

: Combustible Liquid Class III A.None known.:Oxidizing properties

: Not expected to be sensitive to mechanical impact or static discharge. Vapours in the flammable range may be ignited by a static discharge of sufficient energy.

Explosion data: Sensitivity to mechanical impact / static discharge

Use media suitable to the surrounding fire such as water fog or fine spray, alcohol foams, carbon dioxide and dry chemical.

:Suitable extinguishing media

Special fire-fighting procedures/equipment

Firefighters should wear proper protective equipment and self-contained breathing apparatus with full face piece operated in positive pressure mode. Move containers from fire area if safe to do so. Water spray may be useful in cooling equipment exposed to heat and flame.

:

Hazardous combustion products

: Carbon oxides, Hydrocarbons, and other irritating fumes and smoke.

2 2 0NFPA Rating

Health: Flammability: Instability: Special Hazards::

0 - Minimal 1 - Slight 2 - Moderate 3 - Serious 4 - Severe

SECTION 6 - ACCIDENTAL RELEASE MEASURES




Ensure clean-up is conducted by trained personnel only. Keep all other personnel upwind and away from the spill/release. All persons dealing with clean-up should wear the appropriate protective equipment including self-contained breathing apparatus. Refer to Section 8, EXPOSURE CONTROLS AND PERSONAL PROTECTION, for additional information on acceptable personal protective equipment.

Personal precautions :

Ensure spilled product does not enter drains, sewers, waterways, or confined spaces. For large spills, dike the area to prevent spreading.

Environmental precautions :

Spill response/cleanup Evacuate all personnel from affected areas and provide maximum explosion-proof ventilation. Restrict access to area until completion of clean-up. Remove all sources of ignition. Stop the spill at source if it is safe to do so. Contain and absorb spilled liquid with non-combustible, inert absorbent material (e.g. sand), then place absorbent material into a container for later disposal (see Section 13). Notify the appropriate authorities as required.

:

:Prohibited materials Do not use combustible absorbents, such as sawdust.

Special spill response procedures

If a spill/release in excess of the EPA reportable quantity is made into the environment, immediately notify the national response center in the United States (phone: 1-800-424-8802). US CERCLA Reportable quantity (RQ): None reportable.

:

Use in a well-ventilated area. Wear suitable protective equipment during handling. Avoid breathing vapours. Avoid contact with eyes, skin and clothing. Do not ingest. Keep away from heat, sparks, and open flames. Avoid contact with incompatible materials. Wash thoroughly after handling.

Safe Handling procedures :

SECTION 7 - HANDLING AND STORAGE

Store in a cool, dry, well ventilated area, away from heat and ignition sources. Store away from incompatibles and out of direct sunlight. Storage area should be clearly identified, clear of obstruction and accessible only to trained and authorized personnel. Inspect periodically for damage or leaks. No smoking in the area.

Storage requirements :

Incompatible materials : Strong oxidizing agents; Lewis Acids.Special packaging materials : Always keep in containers made of the same materials as the supply container.

SECTION 8 - EXPOSURE CONTROLS AND PERSONAL PROTECTION

Exposure Limits

ACGIH TLV OSHA PEL

STELTWA STELPELIngredients

N/Av N/AvN/Av N/AvDistillates (petroleum),

hydrotreated light

N/Av N/Av30 ppm (AIHA

WEEL)

N/Avd-Limonene

3 ppm ; 6 mg/m³ N/Av3 ppm 6 ppmMonoethanolamine

Ventilation and engineering measures

Use general or local exhaust ventilation to maintain air concentrations below recommended exposure limits. Use explosion-proof equipment.

:

Respiratory protection : Respiratory protection is required if the concentrations exceed the TLV. A NIOSH/MSHA approved air-purifying respirator with the appropriate chemical cartridges or a positive-pressure, air-supplied respirator may be used to reduce exposure.

Skin protection : Wear impervious gloves, such as nitrile rubber. Advice should be sought from glove suppliers.




Eye / face protection : Chemical splash goggles are recommended. A full face shield may also be necessary.

An eyewash station and safety shower should be made available in the immediate working area. Other equipment may be required depending on workplace standards.

:Other protective equipment

General hygiene considerations

: Handle in accordance with good industrial hygiene and safety practice. Avoid breathing vapour or mist. Avoid contact with eyes, skin and clothing. Do not eat, drink, smoke or use cosmetics while working with this product. Upon completion of work, wash hands before eating, drinking, smoking or use of toilet facilities. Remove and wash contaminated clothing before re-use.

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

Physical state Liquid.: Appearance gold:

Odour Peach-like odour.: Odour threshold N/Av:

pH N/Av:

Boiling point 0.870:Specific gravity: N/Av

Melting/Freezing point -40°C:

N/Av:

Coefficient of water/oil distribution

Vapour pressure (mmHg @ 20° C / 68° F)

N/Av:

Solubility in water N/Av:

Vapour density (Air = 1) N/Av: Evaporation rate (n-Butyl acetate = 1)

: N/AvVolatile organic Compounds (VOC's)

N/Av:

Volatiles (% by weight) : N/Av

Flash point 72°C:

Flash point Method N/Av:Auto-ignition temperatureopen cup:

Lower flammable limit (% by vol.) Upper flammable limit (% by vol.)

: :N/Av N/AvN/ApN/Ap: :Flashback observedFlame Projection Length

:Viscosity N/Av

:

Absolute pressure of container

N/Ap

SECTION 10: STABILITY AND REACTIVITIY

Stability and reactivity Stable under the recommended storage and handling conditions prescribed.:

Hazardous polymerization Hazardous polymerization does not occur.:

Conditions to avoid : Keep out of direct sunlight. Keep away from excessive heat, open flames, sparks and other possible sources of ignition. Do not use in areas without adequate ventilation.

Materials To Avoid And Incompatibility

: See Section 7 (Handling and Storage) for further details.Hazardous decomposition products

Refer to Section 5 for additional ‘Hazardous combustion products’.:

Eyes, skin, respiratory system and digestive system.Target organs :

SECTION 11 - TOXICOLOGICAL INFORMATION

Routes of exposure Inhalation: Skin Absorption: Skin & Eyes: Ingestion: YESYESNOYES:

There is no available data for the product itself, only for the ingredients. See below for individual ingredient acute toxicity data.

:Toxicological data

LD50LC50(4hr)

inh, ratIngredients (Rabbit, dermal)(Oral, rat)




Distillates (petroleum), hydrotreated light

N/Av 5000 mg/kg (mouse) 3000 mg/kg

d-Limonene N/Av 4400 mg/kg > 5000 mg/kg

Monoethanolamine > 1210 mg/m³ (> 1.21 mg/L) (mist) (mouse)

1720 mg/kg 1000 mg/kg

Carcinogenic status No components are listed as carcinogens by ACGIH, IARC, OSHA or NTP.:

: Not expected to cause reproductive effects.Reproductive effects

:Teratogenicity Not expected to be a teratogen.:Mutagenicity Not expected to be mutagenic in humans.

:Epidemiology Not available.

Sensitization to material : May cause an allergic skin reaction (e.g. swelling, rash and eczema). No data available to indicate product or components may be respiratory sensitizers.

:Synergistic materials N/Av: Moderate skin irritant. Mild to moderate eye irritant.Irritancy

None known.other important hazards :

Conditions aggravated by overexposure

Pre-existing skin, eye and respiratory disorders.:

Ecotoxicity : See the following tables for individual ingredient ecotoxicity data.

The acute toxicity of the product is measured to be: Toxicity to fish - LC50/96h/Oncorhynchus mykiss (rainbow trout) = 20 mg/LToxicity to daphnia - EC50/48h/Daphnia magna (Water flea) = 27 ppmToxicity to algae - EC50/72h/algae = 40 mg/L

SECTION 12 - ECOLOGICAL INFORMATION

Ecotoxicity data:

NOEC / 21 dayLC50 / 96h M Factor

Toxicity to FishCAS NoIngredients


45 mg/L (Fathead minnow)

64742-47-8 N/Av N/Ap

d-Limonene 0.72 mg/L (Fathead minnow)

5989-27-5 N/Av 1

Monoethanolamine 349 mg/L (common carp)141-43-5 1.2 mg/L/30 days (Japanese ricefish)

None.

CAS NoIngredients Toxicity to Daphnia

EC50 / 48h NOEC / 21 day M Factor

64742-47-8 N/ApN/AvN/AvDistillates (petroleum), hydrotreated light

5989-27-5 1N/Av0.577 mg/L (Daphnia magna)

d-Limonene

141-43-5 None.0.85 mg/L50 mg/L (Water flea)Monoethanolamine




CAS NoIngredients Toxicity to Algae

EC50 / 96h or 72h NOEC / 96h or 72h M Factor

64742-47-8Distillates (petroleum), hydrotreated light

N/Av N/Av N/Ap

5989-27-5d-Limonene N/Av N/Av None.

141-43-5Monoethanolamine 2.5 mg/L/72hr (Green algae)

1 mg/L/72hr None.

Mobility No data is available on the product itself.:

Persistence No data is available on the product itself. Contains: d-Limonene; Monoethanolamine; Distillates (petroleum), hydrotreated light . d-Limonene is considered to be rapidly biodegradable. Distillates (petroleum), hydrotreated light is not considered readily biodegradable. Monoethanolamine is considered to be readily biodegradable.

:

Bioaccumulation potential No data is available on the product itself. Contains: d-Limonene; Distillates (petroleum), hydrotreated light . The log Kow value for d-Limonene is 4.57 and the bioconcentration factor (BCF) is 660, suggesting d-Limonene may bioaccumulate (HSDB). The log Kow value for Distillates (petroleum), hydrotreated light is 2.1 - 5 and the bioconcentration factor (BCF) is 61 - 159, suggesting Distillates (petroleum), hydrotreated light may bioaccumulate (IUCLID).

:

Other Adverse Environmental effects

No data is available on the product itself.:

Handle waste according to recommendations in Section 7.:Handling for Disposal

SECTION 13 - DISPOSAL CONSIDERATIONS

Improper disposal can cause damage to the environment. Dispose in accordance with all applicable federal, state, provincial and local regulations.

:Methods of Disposal

If this product, as supplied, becomes a waste in the United States, it may meet the criteria of a hazardous waste as defined under RCRA, Title 40 CFR 261. It is the responsibility of the waste generator to determine the proper waste identification and disposal method. For disposal of unused or waste material, check with local, state and federal environmental agencies.

RCRA :

SECTION 14: TRANPORT INFORMATION

Regulatory

Information UN Number Shipping Name Class

Packing

Group Label

noneNone.TDG not regulatedNot regulated.

Not regulated unless shipping internationally by sea.Additional

information

TDG

noneNone.49CFR/DOT not regulatedNot regulated.

None.Additional

information

49CFR/DOT

SECTION 15 - REGULATORY INFORMATION

US Federal Information:

Components listed below are present on the following U.S. Federal chemical lists:




Ingredients CAS #TSCA

Inventory

CERCLA

Reportable

Quantity(RQ) (40

CFR 117.302):

SARA TITLE III:

Sec. 302,

Extremely

Hazardous

Substance, 40

CFR 355:

SARA TITLE III: Sec. 313, 40 CFR

372, Specific Toxic Chemical

Toxic Chemicalde minimus

Concentration


64742-47-8 N/Ap N/Ap N/ApYes No

d-Limonene 5989-27-5 N/Ap N/Ap N/ApYes No

Monoethanolamine 141-43-5 N/Ap N/Ap N/ApYes No

SARA TITLE III: Sec. 311 and 312, MSDS Requirements, 40 CFR 370 Hazard Classes: Fire Hazard; Acute Health Hazard. Chronic Health Hazard. Under SARA Sections 311 and 312, the EPA has established threshold quantities for the reporting of hazardous chemicals. The current thresholds are 500 pounds for the threshold planning quantity (TPQ), whichever is lower, for extremely hazardous substances and 10,000 pounds for all other hazardous chemicals.

Ingredients CAS #

California Proposition 65

Listed Type of Toxicity

State "Right to Know" Lists

CA RIMA PAMN NJ

64742-47-8Distillates (petroleum), hydrotreated light

No No No No No No NoN/Ap

5989-27-5d-Limonene No No No No No No NoN/Ap

141-43-5Monoethanolamine No Yes Yes Yes Yes Yes YesN/Ap

US State Right to Know Laws:

The following chemicals are specifically listed by individual States:

WHMIS information: Refer to Section 2 for a WHMIS Classification for this product.

Canadian Environmental Protection Act (CEPA) information: All ingredients listed appear on the Domestic Substances List (DSL).

Canadian Information:

This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations

(CPR) and this MSDS contains all the information required by the CPR.

HMIS Rating *2 Reactivity:Flammability:Health: 02

: - Chronic hazard 0 - Minimal 1 - Slight 2 - Moderate 3 - Serious 4 - Severe

SECTION 16 - OTHER INFORMATION

: ACGIH: American Conference of Governmental Industrial Hygienists CAS: Chemical Abstract Services CERCLA: Comprehensive Environmental Response, Compensation, and Liability Act of 1980 CFR: Code of Federal Regulations CNS: Central Nervous System DOT: Department of Transportation HMIS: Hazardous Materials Identification System HSDB: Hazardous Substances Data Bank IARC: International Agency for Research on Cancer Inh: Inhalation LC: Lethal Concentration LD: Lethal Dose MSHA: Mine Safety and Health Administration N/Ap: Not Applicable N/Av: Not Available

Legend




NFPA: National Fire Protection Association NIOSH: National Institute of Occupational Safety and Health NOEC: No observable effect concentration NTP: National Toxicology Program OSHA: Occupational Safety and Health Administration PEL: Permissible exposure limit RCRA: Resource Conservation and Recovery Act RTECS: Registry of Toxic Effects of Chemical Substances SARA: Superfund Amendments and Reauthorization Act STEL: Short Term Exposure Limit TDG: Canadian Transportation of Dangerous Goods Act & Regulations TLV: Threshold Limit Values TWA: Time Weighted Average WHMIS: Workplace Hazardous Materials Identification System1. ACGIH, Threshold Limit Values and Biological Exposure Indices for 20132. International Agency for Research on Cancer Monographs, searched 20133. Canadian Centre for Occupational Health and Safety, CCInfoWeb databases (Chempendium, HSDB and RTECs). (2013)4. Material Safety Data Sheet from manufacturer.5. US EPA Title III List of Lists - October 20126. California Proposition 65 List - November 8, 2013

References :

Prepared for:

RBM HoldSolutions101 - 2762 190th StSurrey, BC, Canada V3S 3W6Telephone: (604) 531-8333Direct all enquiries to: RBM HoldSolutions

Prepared by:

ICC The Compliance Center Inc.http://www.thecompliancecenter.com

DISCLAIMER OF LIABILITY

This Material Safety Data Sheet was prepared by ICC The Compliance Center Inc using information provided by / obtained from RBM HoldSolutions and CCOHS’ Web Information Service. The information in the Material Safety Data Sheet is offered for your consideration and guidance when exposed to this product. ICC The Compliance Center Inc and RBM HoldSolutions expressly disclaim all expressed or implied warranties and assume no responsibilities for the accuracy or completeness of the data contained herein. The data in this MSDS does not apply to use with any other product or in any other process.

This Material Safety Data Sheet may not be changed, or altered in any way without the expressed knowledge and permission of ICC The Compliance Center Inc and RBM HoldSolutions.

:

Preparation Date (mm/dd/yyyy)

11/19/2013

END OF DOCUMENT

SDS

Safety Data Sheet

SECTION I: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Material Name / Identifier - RBM BilgeCoat Material Intended Use - Bilge Line Neutralizer Chemical family - Proprietary Mixture

WHIMIS Classification - N/A TDG/DOT Classification - Not Regulated

Supplier’s Name: - RBM HoldSolutions (A division of Roberts Marine Solutions Ltd.) Address: - Unit 101 – 2762 190th Street City & Province: - Surrey, British Columbia, Canada V3S 3W6 Telephone (Including Emergency) - +1 604 531 - 8333 E-mail (Including Emergency) - [email protected]

SECTION lI: COMPOSITION / INFORMATION ON INGREDIENTS

Ingredients Percentage (W/W) LD50 and LC50: Proprietary <10% N/E

SECTION III: PHYSICAL DATA

Physical state: Liquid

Appearance: Yellowish Specific Gravity (H20=1): 1.03 @ 20° C

Viscosity (@ 40°C) N/E Boiling Point (°C): N/E Solubility in Water: Miscible Flash Point/Method (°C): N/A

Odor: Mild Odor Threshold: N/E Vapor Pressure (Hg @ 20°C): N/E Evaporation Rate: N/E Freezing Point (°C): N/A pH 11.79

VOC Content (%) N/A

SECTION IV: FIRE AND EXPLOSION HAZARD DATA

Flammable: No Combustible: No Reactivity: No Special Firefighting Procedures: Carbon Dioxide, Dry Chemicals, Water Explosion Hazards: Non-Explosive

SECTION V: REACTIVITY DATA

Chemical Stability: Stable Incompatiblity (Materials to Avoid): Strong Acids Hazardous Decomposition Products: None Hazardous Polymerization: Will Not Occur Conditions to Avoid: Excessive Heat

SECTION VI: TOXICOLOGICAL PROPERTIES Route of Entry: Eye / Skin Contact / Ingestion / Inhalation

Eye : Contact will cause severe stinging and temporary irritation. Skin: Prolonged or repeated contact may cause slight irritation. Inhalation: Not an inhalation hazard under normal operating conditions. Ingestion: Nausea, stomach cramps, vomiting. Carcinogenic: None of the ingredients are listed as carcinogenic.

SECTION VII: PRECAUTIONS FOR SAFE HANDLING AND USE

Protective Handwear: Rubber of neoprene gloves recommended Protective Eyewear: Safety glasses with side shields, face shield or goggles recommended if risk of contact. Other Protective Clothing/Equipment: Eye Bath, safety shower and full apron.

Respiratory Apparatus: Not Required under normal use conditions. Local/Mechanical Exhaust: Good general ventilation is sufficient. Work/Hygenic Practices: Wash hands before eating, drinking, smoking or using toilet facilities. Waste Disposal: Review federal or provincial regulations prior to disposal. Storage and Handling: Store in fiberglass, polyethylene or polypropylene containers.

1


SECTION VIII: FIRST AID MEASURES

Eyes: Remove contact lenses. Flush with water for 15 minutes. Consult physician if irritation develops.

Skin: Wash with Soap and Water. Consult physician if irritation develops. Launder clothing before use.

Ingestion: If swallowed, call a physician. Do not induce vomiting. Drink large quantities of water to dilute.

Inhalation: Remove to Fresh Air.

SECTION IX: ADDITIONAL INFORMATION

HMIS RATING: Health: 1 Flammability: 0 Reactivity: 0 PPE: B

Information for this Material Safety Data Sheet was prepared from sources considered reliable. While every effort has been made to ensure full disclosure of product hazards, data is not available in some cases and is so stated where applicable. The manufacturer assumes no liability or responsibility, and no warranty is expressed or implied, in cases where products are mishandled, misused or instructions are not strictly observed. Each recipient of this MSDS is encouraged to study it carefully to understand this product.

WHMIS / TDG: N/Ap

Non corrosive to skin. (as defined and tested with the US OSHA’s Hazard communication Standard, DOT Hazard Material Regulations, Canada WHIMIS Regulation and TDG Regulations. Classified as a mild skin irritant as per the 1992 OECD Guideline for testing of chemicals, Number 404 “Acute Dermal Irritation/Corrosion”.

Under reference to MEPC 63/23/Add. 1, Annex 24 Resolution MEPC 219(63) as adopted on March 02, 2012; RBM HoldSolutions herewith declares that the product identified as LA5495 and marketed as RBM BilgeCoat by RBM HoldSolutions, the nature of which is covered in this Safety Data Sheet meets the criteria as non-harmful to the marine environment as described under section 1.7.5 of above resolution. This statement is not valid for any other solutions or chemicals, which may be put on the market with an identical or similar product name. The names of RBM HoldSolutions and RBM BilgeCoat must be mentioned on the product label and in the Safety Data Sheet. Disclaimer / Notice to reader: RBM HoldSolutions expressly disclaims all expressed or implied warranties of merchantability and fitness for a particular purpose, with respect to the product or information provided herein and shall under no circumstances be liable for incidental or consequential damages. Do not use ingredient information and/or ingredient percentages in this SDS as product specification. For product specification information, refer to a Product Specification Sheet and/or a Certificate of Analysis. These can be obtained through RBM HoldSolutions. All information appearing herein is based upon data obtained from the manufacture and/or recognized technical sources. While the information is believed to be accurate, RBM HoldSolutions makes no representations as to its accuracy or sufficiency. Conditions of use are beyond the control of RBM HoldSolutions and therefore, users are responsible to verify this data under their own operating conditions to determine whether the product is suitable for their particular purposes and they assume all risks of their use, handling and disposal of the product or from the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein and does not relate to its use in combination with any other material or in any other process.

Prepared by: Contact details: Date issued: Replaces:

RBM HoldSolutions Phone: +1 604 531 - 8333

Email: [email protected] December 23, 2013 December 13, 2012

2


Documents

instruction manuals