Interface Units - YGHP

InterfaceUnits

YGHPONE CROWN PLACE

WITH OUR AMAZING SERVICESUPERIOR PRODUCTS AT

UNBEATABLE PRICES WHY GO ANYWHERE ELSE?

YGHP recognised a gap in the market place where high quality products were required with the same level of technical detail,

while offering a cost saving.

Based in Staffordshire with a combined HVAC industry experience of 50 years YGHP are ideally located to serve both the

North and South of the UK, as well as Republic of Ireland.

With a dedicated mechanical design department, service department and customer services YGHP are committed to

assisting the project, large or small in all areas of design through to procurement.

Our fully trained team are strategically located throughout the UK to visit our clients and help them with the projects.

As YGHP are manufacturers we can bespoke design, build and deliver to strict project requirements.

Put your trust in YGHP like many other companies...

Contact us today on 0845 0170796 or www.yghp.co.uk

• Heat interface units are a complete solution for apartments for hydraulicseparated systems.

• Secondary system radiators or under floor heating.• Balancing valves can be radiators or under floor heating.• Stainless steel heat exchanger and thermostatic controlling valve to have

a stable temperature domestic hot water Up to 35 It/min.• Stainless steel heat exchanger is used to hydraulically separate the apartment

from the primary system.• Thermostatic controlled valves are used to control the secondary side supply

temperature.• Energy efficient electronically controlled pump controls the flow of secondary

side heating.• All the consumption of heating and domestic hot water preparation can be

measured by one heat meter and cold water meter.• All the piping is stainless steel.• Stainless Steel pipe 18 x 1mm (AISI 304).• Galvanised back plate.• Brazed heat exchanger for hot water.• Brazed heat exchanger for heating.• Special immersion thermostatic control valve for hot water.• Special immersion thermostatic control valve for heating.

With over 155,000 units sold worldwide the YGHP HIU is a firmfavorite with consultants, installers and users.

YGHP offer a 5 year warranty on all interface units.

• EPP fully insulated Cover.• Differential pressure balancing valve inlet 20-65 kpa.• Energy efficient electronically controlled pump.• Heat meter ultrasonic mid class 2.• Brass Connections.• In line strainers.• Mounting plate with ball valves.• On-wall cabinets (Optional)

HEAT INTERFACE UNIT (HIU)

Cold water meter spare part

(Demand on request)

‘THE RELIABLE COST EFFICIENT, STABLE CONTROLLED HIGH PERFORMING HIU’


INDIRECT HIUDual differential Pressure control valves gives stable and continuous supply simultaneously of Heating and DHW. Maximum working pressure 25 bar, with a range of 2.0 bar to 6.5 bar.

Latest SWEP Plate heat exchangers offering exceptional performance.

Water arrestor (hammer) to avoid noise in the system.

EPP casing to ensure minimum heat losses.

DHW thermostatic control valves offer the most accurate and effective temperature control. The sensor is within the PHE, making this an instant response. The thermostatic valves are optimised for minimal idle consumption.

Heating thermostatic control valves ensures an accurate temperature across all heating circuits or under floor heating manifolds

Low energy – each floor heating component has an electronically-controlled circulation pump (DN 15 size and 7 m hydraulic performance) which is exclusively designed for circulating for heating systems with constantly changing volume flows.

Air vents – multiple air vents to eradicate air within primary and secondary systems.

The inlets and outlets of the HIU-Indirect: The dimensions of the HIU-Indirect:

1. Domestic hot water outlet.2. Domestic cold water supply.3. Apartment heating supply.4. Apartment heating return.5. Heating water supply.6. Heating water return.7. Safety valve drain.

Please pay attention to the stickers which shows the inlets, outlets and direction of the flow


DIRECT HIU

The Direct HIU has a plate heat exchange sized to meet the DHW loads.

Heating is direct from the primary communal side, regulated by an electric actuator which can be linked to a room thermostat to give comfort and control.

Balancing valves for complete unit and radiator side is used to control the pressure difference across and in the system.

Stainless steel heat exchange and thermostatic controlling valve to have a stable temperature domestic hot water.

Up to 23 It/min. Large sizes can be produced upon request.

All the consumption of heating and domestic hot water preparation can be measured by one heat meter and cold water meter.

All piping is stainless steel.

16 bar rated, tested in the factory before leaving the site.

The inlets and outlets of the HIU-Radiator:

The dimensions of the HIU-Radiator:

1. Domestic hot water outlet.2. Domestic cold water supply.3. Apartment heating supply.4. Apartment heating return.5. Heating water supply.6. Heating water return.

Please pay attention to the stickers which shows the inlets, outlets and direction of the flow

• Combined Interface Units Are A Complete Solution For ApartmentsFor Hydraulic Separated Systems. Heating, DHW & Cooling.• Secondary System: Radiators Or Underfloor Heating.• Balancing Valves Can Be Radiators Or Underfloor Heating.• Stainless Steel Heat Exchanger And Thermostatic Controlling Valve ToHave A Stable Temperature Domestic Hot Water Up To 55 It/min.• Stainless Steel Heat Exchanger Is Used To Hydraulically Separate TheApartment From The Primary System.• Thermostatic Controlled Valves Are Used To Control The SecondarySide Supply Temperature.• Energy Efficient Electronically Controlled Pump Controls The Flow OfSecondary Side Heating.• All The Consumption Of Heating And Domestic Hot Water PreparationCan Be Measured By One Heat Meter And Cold Water Meter.• All The Piping Is Stainless Steel (Insulated)• EPP Thermal Covers

• Stainless Steel Pipe 18 x 1mm (AISI 304).• YGHP Built Galvanised Back Plate.• Brazed Heat Exchanger For Hot Water.• Brazed Heat Exchanger For Heating.• Brazed Cooling Exchanger For Cooling.• Special Immersion Thermostatic Control Valve For Hot Water.• Special Immersion Thermostatic Control Valve For Heating.• Special Control Valve For Cooling.• EPP Thermal Covers To Prevent Condense.• Condense Prevention Plate.• Differential Pressure Balancing Valve Inlet 20-65 kpa.• Energy Efficient Electronically Controlled Pump.• Heat Meter - M-BUS Class 2 Ultrasonic.• Cold Water Meter M-BUS Class 2.• Brass Connections.• In-Line Separators.• First Fix Mounting Plate With Isolation Ball Valve Kit.• Flushing By-Pass Kit.

Combined Interface UnitYGHP are a select few manufacturers who can offer a combined heating, hot water and cooling interface unit.

Having a unit that combines all equipment in one position helps lower installation costs, helps save space along with offering ease of use for the home owner. Available in 20 - 120kW outputs.



YGHP HIU Plate Heat ExchangersThe SWEP PHE is developed to meet the market’s highest thermal demands for tap water and heating production. The unique construction, with integrated start and end plates, combined with high compactness and efficiency means the PHE offers a very versatile solution.

• Up to 120 plate design• A maximum flow of 6 m3/h.• Stainless steel 316 plate• Copper brazing• WRAS approved

The Brazed Plate Heat Exchanger (BPHE) is constructed as a plate package of corrugated channel plates with a filler material between each plate.

During the vacuum brazing process, the filler material forms a brazed joint at every contact point between the plates, creating complex channels.

The PHE allows media at different temperatures to come into close proximity, separated only by channel plates that enable heat from one media to be transferred to the other with very high efficiency.

The concept is similar to other plate and frame technology, but without the gaskets and frame parts.

SWEP optimizes the use of energy,

material, and space in heating and

cooling systems


Inline cast iron pump housing

7,7= delivery head in [m] at Q = 0 m3/h

The pump is controlled by Push button technology SC = P-v, P-c, constant speed I, II, III

Control box orientation 12 o’clock (3, 6, 9 o’clock: also available)

Threaded connection DN15 (25, 30: also available )

Automatic adjustment of pump output to continuously varying load conditions of the hydraulic system. Increasing the control and helping achieve maximum performance.

Prevention of flow noise to help the YGHP HIU operate in silence.

• Energy Efficiency Index (EEI) ≤ 0.2.• Max. delivery head: 7,7 m.• Mains connection: 1~230 V +10%/-15%, 50/60 Hz (IEC 60038 standard voltage)• Low voltage directive: 20014/95/EC Conform• Protection class: IPx4D

HIU Electronically Controlled PumpAs the first high-efficiency pump in the world, the Wilo defined energy efficiency class A for stand-alone circulators, thereby setting a new standard. Wilo extended this product technology towards new pump ranges especially for requirements of the OEM industry.

Standard factorysetting

1 - TANK'S BODY (EPOXY POWDER COATING) 2 - AIR VALVE3 - RUBBER MEMBRANE4 - WATER CONNECTION

Features:

Flat expansion tank with a rectangular shape to optimise spaces in closed circuits.

Rubber diaphragm fixed membrane.

100% Made in Italy.

Produced according to the standards established by PED 2014/68/UE and DIN EN 13831 regulations.

Quality certified and guaranteed by international regulations.

Epoxy powder exterior painting to guarantee a high level of protection against oxidation and a fine aesthetic final quality.

Accurate quality controls during all manufacturing process phases.

CIMM membrane expansion tanks are CE marked, in compliance with the European Directive 2014/68/UE (PED), which harmonises national laws of member states regarding pressure equipment and aims to ensure their free circulation throughout Europe.

CIMM products have been approved by the most important international certifying bodies.

HIU Internal Expansion Vessel

The use of cutting-edge technology and creativity allows CIMM to offer innovative solutions that meet the most restrictive requirements set by international regulations.

Fitted internally to achieve a compactly

designed HIU

CIMM SPA shock arrestor prevents vibrationin the HIU and also aiding towards a silent operation.

Expanded Polypropylene (EPP) is a highly versatile closed-cell bead foam that provides a unique range of properties, including outstanding energy absorption, multiple impact resistance, thermal insulation, buoyancy, water and chemical resistance, exceptionally high strength to weight ratio and 100% recyclability.

EPP can be made in a wide range of densities, from 15 to 200 grams per litre, which are transformed by moulding into densities ranging from 18 to 260 grams per litre.

Individual beads are fused into final product form by the steamchest moulding process resulting in a strong and lightweight shape.

The manufacturing process is complex, requiring both technical expertise and specialised custom equipment.

Polypropylene resin is combined with other ingredients in a multi-step proprietary process. Under tightly controlled conditions, extruded pellets expand to become consistently shaped beads of expanded polypropylene foam.

EPP foam beads are then injected into molds.

Pressure and steam heat fuse the beads into a finished shape.

The finished EPP foam part becomes a key component in sub-assemblies incorporated in the original equipment manufacturer’s product.

Porous EPP is comprised of cylinder-shaped polypropylene beads, which adds air space between the beads in the final moulded form, which enhances beneficial acoustical insulating effects and reduces weight.

The benefit of having EPP over metals and inferior materials are:Reliability over a wider range of temperatureLow thermal conductivityEco-friendly

EPP Thermal Covers

Available EPP Applications: Front CoverRear Cover

Plate Heat Exchangers Pipework

Isolation Valves

'Heat is kept within the unit for maximum efficiency'Contact us today on 0845 0170796 or www.yghp.co.uk


YGHP Heat Meter & Smart BillingYGHP offer a complete range of heating, cooling and water meters. The heat and cooling meter can be factory fitted to the YGHP HIU to save on fitting time as well as space saving. Being factory fitted the HIU arrives ready to be installed and start providing a cost effective solution for heat networks.

The biggest water meter manufacturer in Turkey BAYLAN is one of the biggest source of pride to Turkish labour and workforce from Middle East to Europe, Asia to Africa with the experience more than half a century.

BAYLAN has begun to work in 1955 at fixing, maintaining and calibrating both water and electrical meters. Adding designer identity to it’s experience more than half a century and technological superiority.

BAYLAN has pioneering Turkish water and electricity meter sector with qualified and authorized personnel providing lots of innovation, pioneer service and technology to instrument tools.

First fix kit:

Smart Card Billing.

All the operations based on customers are made with the customer card. When assigned, all the customer specific information such as tariffs, emergency credit, critical credit are copied to the customer card. When the water meter reads the card, all this information is downloaded to the water meter.

Customers can top up credit to their water meters by using this card. Water meter transfers all the information and its current state to the main center by the customer card. The central system receives all the information such as (battery level, alert states, consumption index, recent credit loading date) when the customer card is read at the vending point.

YGHP ultrasonic m-bus class 2 heat meter



PREFABRICATED MEP UTILITY UNIT & CUPBOARDYGHP offer a design, build and deliver service for off site prefabricated utility cupboards for all types of projects big and small.The advantages of off site fabrication include:• Reduced cost.• Reduces project time.• Fewer project labour hours.• Fit and forget installation.• Can be tailored to suit all project requirements including : HIU, CIU, heart

pumps, water heaters, under floor and MVHR.Being a bespoke service we can include all project requirements within a budget saving time and cost.

BESPOKE OPTIONS

AVAILABLE

As well as Utility cupboards, YGHP can design and manufacture corridor module runs.

These modules from the utility cupboards through the corridors to the risers speed up the installation significantly.

Easy to store on site - saving time and helping keep projects on schedule.

Pipe work can be polymer, copper, steel or stainless steel.

Fully installed by our own dedicated installation team.

YGHP have numerous sites throughout London and the UK where prefabricated utility cupboards and corridor modules have been installed and provided a cost effective method of prefabrication.

Documents

Interface Units - YGHP