Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
www.jkcementuae.com
PROTECTION DURABILITY WHITENESS
JK WALL PUTTY
Certified to :ISO 9001 (QMS) & ISO 14001 (EMS)OHSAS 18001 & SA 8000
JK WALL PUTTY
• JKWALLPutty is awhite cement based finepowderwhichprovidesanidealfinishingforconcrete/cementplasteredwallsandceiling.
• Itprovidesanidealbaseforpainting.• Itprovidesdampresistantsmoothfinishforfurtherapplication
ofallkindsofpaints. (Dampresistancemeansresistance towaterinhumidair¬physicalwatercontacts/leakages).
• Itgivespleasinglooktointeriors&exteriors.• Itisfinepowdertobemixedwithwaterasadvisedfordirect
applicationonplasteredsurfaceoftheinteriors/exteriorstogetsilkyandshinyfinish.
• Can be used concrete, renderedwall, hollow block, precastwalls,concreteceilings,calciumsilicatebricks&aerated lightweightblocks.
• Notrecommendedforuseonpaintedorothernon-cementitioussurfaces.
SURFACE PREPARATION New surfaceNewsurfacerequirespreparationsuchasremovalofdust,dirtandforeignmatter. In caseof cracks, voids&damages it shouldberepaired.Surfacesshouldbe in just-wetcondition,prior toputtyapplication.
Old Unpainted SurfaceAllloosematerial,organicgrowth,dirt,dust,etc.mustberemovedwithsteelbladeorwirebrush.Surfaceshouldbeinjust-wetcondition,priortoputtyapplication.
Old Painted SurfaceScrubthesurfacewithcoarsewirebrush/sandpaperandcleanthoroughlyso that it is free fromoldpaint /dustparticles till thecementitious/plasteredsurfaceisseen.Surfacecouldbewashedwithwater, however ensuring that surface should be in just-wetcondition,priortoputtyapplication.
Very Rough SurfaceIfsurfaceplasterwasrough,1stapplywhitecement/whitecementmortarandlevelthesurface.Curethesurfacefor2days,beforestartingputtycoat.Surfaceshouldbe in just-wetcondition,priortoputtyapplication.
Very Smooth SurfaceIf the surfacewasmadeby cement ghutai (smoothening)whichnormally is very smooth, bondingwith puttymay not becomesufficientlystrong.Scrapingthesurfacewithemerystone/paperisrecommendedbeforeputtyapplication.Surfaceshouldbeinjust-wetcondition,priortoputtyapplication.
Area near the skirtingExtra care is recommended for the area adjacent to skirting ofthefloor (at leastareaup toone feetabove theskirting).Duringgrinding of the skirting and floor, slurry is generated. It sticks tothewalland ifnotcleanedproperly,wallputtyon itwillnotgivegoodresults.Chancesofflaking/pooradhesion.Areaat leastuptoonefeetabovetheskirtingshouldbecleanedwithwirebrushandwashedthoroughlysothatslurrydepositedonthewallduringgrinding is totally removed. After drying the wall, putty can beappliedasnormal.
Plaster showing sign of Efflorescence / salt depositionIf due to saltywateror salts in sand/bricks,problemof efflores-cenceisobservedthenplasteredsurfaceshouldbetreatedwithmild acid like citric acid before application of J.K.Wall putty.Otherwise,wallputtywillnotsticktothewallandproblemofflakingmayarise.After30minutesoftreatingthesurfacewithmildacid,surfaceshouldbewashedthoroughlysothatnoacidremainsonthewall.Afterdryingproperly,wallputtycanbeappliedasnormal.Thistreatmentshouldbedoneunderpropersupervision.
* just-wet condition could be achieved by applying coat of water with soft brush.** In case of wall exposed to sun, more water spraying shall be done to take away heat from the surface and then bring wall to just-wet condition.
PREPARATION OF J.K. WALL PUTTY PASTE • Takerequiredquantity
ofJ.K.WallPuttyinapan.
• Mix half of requiredwaterquantityintoit.
• Knead/MixthePutty& wait for few min-utes.
• Mixremainingquantityofwatertogetdesiredconsistency.• @35-40%waterby volume is required topreparepasteof
goodconsistency.• Mix vigorously for 5-10minutes formaking lump freeand
uniformpaste,asshown.• Productshouldbemixed insuchquantities that itcouldbe
usedwithin2hrsofitspreparation.• Mixingcouldbedonemanuallyorbysuitableelectricmixer.
COVERAGE We recommend:• Maximumtwocoats(Layers)ofJ.K.WallPutty.• Maximumthicknessof1stcoat(Layer)1.5mm.• Maximumthicknessof2ndcoat(Layer)1.0mm.• Approxachievablecoverageis35sqft./mmthickness/kgof
J.K.wallputty.• Forrecommendthicknessabove,thecoverageachievableis
@14sq.ft/kgof j.k.wallputty.Or280sq.ft/20kg.bagofJ.K.WallPutty.However,actualcoverageachieveddependsonthebasesurfacecondition&finishedthickness.
APPLICATION
• Ensure that surface is plastered OR made with cementitious ma-terial.
• Ensure that surface is totally clean.
• Ensure that surface is moderately rough (neither too-rough not too-smooth).
• Ensure that surface is just-wet. Over-wet-ting resulting in ac-cumulation of water on surface should be avoided.
• Apply first coat. Use spatula/blade/trowel on the wall with “bottom to top” Configuration.
• Apply second coat preferably after @ 4 hrs in hot season & after @ 12 hrs in cold season. Second coat shall be applied “horizontally” to even out application marks of 1st coat, if any.
• Re-mix putty paste again for @ 1 minute, if it is left un-disturbed for @ 30 minutes.
• Allow complete drying for @ 3 days and then use fine emery paper to remove application mark, if any
OR• Half an hour after application of 2nd coat smoothening
could be done with trowel.• Paint could be done after 3 or more days of putty work
but it shall be ensured that putty is completely dry before applying paint.
• Clean application tools with clean water.
PRECAUTION
• AlthoughJ.K.WallPuttydonotcontainanytoxicmaterial,userubbergloveswhilemixing.
• Precautionshouldbetakentoavoiddustinhalationwhilehan-dlingputtypowderorduringremovalofapplicationmarkswithfineemerypaper-saywearingnosemask.
• Keeptheproductoutofreachofchildren.
• Onceputtypastehashardened,itshallnotbeusedbyaddingwater.
WETTING
Usualcuringwithlotofwaterisnotneeded.Keepinginviewtheambienttemperature,needbasedwettingisrecommended.
• Just-wetthesurface,priortoputtyapplication.• Afterapplyingfirstcoatwetthesurfacegently.• Afterapplicationofsecondcoat,wetsurfacetwiceadayfor
atleastoneday,ifseasondemandsit.Watershallbeappliedgently.
STORAGE
• StoreJ.K.WallPuttyinadryplace.• Openthebagjustbeforeuse.
SALIENT FEATURES OF J.K. WALL PUTTY
• Wedonotrecommendmixingofpigments/stainerin• J.K.WallPutty.• Qualityofpaintedsurfaceisdirectlyproportionaltoqualityof
un-paintedsurface.J.K.WallPuttyrendersidealconditionasun-paintedsurfaceforpaintapplication.
• PaintcanbeappliedonJ.K.Wallputtywithorwithoutprimer.However,useofprimershallgivecostadvantage incaseofexpensivepaints.
• Lustrous white and smooth surfacewhich can be left un-painted.
• Life of J.K.Wall Putty is as long as the life of grey cementplasterunderneath.
• Itpreventsgrowthofalgaeandfungusonwalls.
• Anykindofdistempercanbeappliedonitdirectly.
• Texturedfinishcanbeobtainedbyuseoftexturingtools.
• As prevalent in case of other non-cement putties, primerapplication is not recommended before J.K. Wall Puttyapplication.Thissavescost.
PACKAGING
• 1kgP.P.packetsputin20kgssecondaryHDPEbagforease
ofhandling.
• 5kg packs put in 20 kg secondary
HDPEbagforeaseofhandling.
• 20kglaminatedP.P.bag.
• 40kglaminatedP.P.bag.
Surface Preparation Method of Application
Standards Compliance :
•ASTMC191 •ASTMC948 •ASTMC348•ASTMC349 •ASTMD4541 •ASTMC1794•USEPA24
Technical parameters :
Appearance White Color Powder
WetDensity(Kg/M3) 1670
SettingTime 6 - 12 Hours
Flexural Strength 3.13 N/mm2
Compressive Strength 10 N/mm2
Pull-Off Strength 0.63 N/mm2
APPLICATION TOOLS (FOR APPLICATION & TEXTURES)
PERFORMANCE AT A GLANCE
Properties J.K. Wall Putty Traditional Putty POP
AreaofApplication Canbeappliedonexterior/ex-posedsurface/interior/ceiling
Can’tbeappliedonexterior/exposedsurface.
Can’t be applied on exterior /exposedsurface
BindingProperty Cement based putty, hencegoodbindingproperty.
Very low binding property duetouseofchalkpowder. Lowbindingproperty.
CoverageArea14Sq. ft /kg.onnewsmooth
plasteredwallforfinishedthickness.
@10sq.ft/kgforequivalentthickness.
6-7sq.feet/kgforequivalentthickness.
Consistency
Consistency in quality as it isFactorymadewithstandard
ingredients&continuousqualitycontrol.
Large variation in properties.Qualityofingredients
varyingfromareatoarea.Hugevariationinquality
ConsumptionofDistemper LessDistemperisrequiredbecauseofitslowabsorption.
RequiresmoreDistemperbecauseofhighabsorption.
RequiresmoreDistemperbecauseit’sabsorptionismore.
CostLessultimate costdue to longlife span, No primer cost, low
paintabsorption.Ultimatecostishigh. Ultimatecostisquitehigh.
Durability Moredurableduetogoodbindingproperty. Lessdurable Lessdurable
LookBetter apperance due to veryhigh whiteness (Min 93%) of
putty.
AppearanceisnotlikeJKWPduetoitsyellowishbase. Yellowsurfaceisachieved
Primercoatonbasesurface NorequirementofPrimerCoat Primer coat application is amust Primercoatisamust
Strength Highlikecement Lowstrength Verylowstrength
WaterResistance goodresistencetodampness Itdoesn’tresistdampness Peelsoffwhencomesincontactwithwater
Note:Informationgiveninthisbookletisforgeneralguidance.Specificinstructionforvarioussiteconditionscanbefurnishedondemand.However,Companyisnotresponsibleforanywrongapplicationoftheproduct.