SERVICE MANUAL

COPYRIGHT 2008 Victor Company of Japan, Limited No.YA6042008/4

WIDE LCD TELEVISIONYA60420084SERVICE MANUAL

LT-42S90B/B, LT-42S90B/G,LT-42S90B/L, LT-42S90B/S

COPYRIGHT 2008 Victor Company of Japan, Limited

TABLE OF CONTENTS1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-63 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-104 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-165 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

BASIC CHASSIS

FT4

No.YA597: LT-42DS9 series No.YA598: LT-42S90BU

1-2 (No.YA604)

SPECIFICATION

Design & specifications are subject to change without notice.

Items ContentsDimensions ( W H D ) 98.1 cm 67.3 cm 27.5 cm [Included stand]

98.1 cm 62.7 cm 7.5 cm [TV only]Mass 23.3 kg [Included stand]

19.3 kg [TV only]Power Input AC220V - AC240 V, 50 HzPower Consumption 183 W (Standby: 0.5 W)TV RF System CCIR (B/G, I, D/K, L)Colour System PAL

SECAMNTSC 3.58/4.43 [EXT only]

Stereo System NICAM (B/G, I, D/K, L), A2 (B/G, D/K)Receiving Frequency VHF: 47MHz - 470MHz

UHF: 470 MHz - 862 MHzCATV: 116MHz - 172MHz / 220MHz - 469MHz

IntermediateFrequency

VIF 38.9MHz (B/G, I, D/K, L)SIF 33.4MHz (5.5MHz :B/G)

32.9MHz (6.0MHz :I)32.4MHz (6.5MHz :D/K)

Colour SubCarrier Frequency

PAL 4.43MHzSECAM 4.40625MHz / 4.25MHz

NTSC 3.58MHz / 4.43MHzTeletext System FLOF (Fastext level 2.5)

TOPWST(World Standard system)

LCD Panel 42V-inch wide aspect (16 : 9) Screen Size Diagonal : 105 cm (H: 93.0 cm V: 52.3 cm) Display Pixels Horizontal : 1920 dots Vertical : 1080 dots (FULL HD)Audio Power Output 10 W + 10 WSpeaker 4.5 cm 13.0 cm, oblique type 2Aerial Terminal (VHF/UHF) 75 unbalanced, coaxialEXT-1 / EXT-2 (Input / Output) 21-pin Euro connector (SCART socket ) 2EXT-3 (Input) Component Video

750p / 1125i / 1125p

625p / 525p / 625i / 525i

RCA pin jack 3Y : 1 V (p-p) (Sync signal: 0.35V(p-p), 3-value sync.), 75 Pb/Pr : 0.35V(p-p), 75 Y : 1 V (p-p), Positive (Negative sync.), 75 Cb/Cr : 0.7V(p-p), 75

Video 1V (p-p), Positive (Negative sync provided), 75 , RCA pin jack 1Audio 500 mV(rms) (-4dBs), high impedance, RCA pin jack 2

EXT-4 / EXT-5 / EXT-6 (HDMI Input)

VideoAudio

HDMI 2-row 19pin connector 3(Digital-input terminal is not compatible with picture signals of personal computer)Supported format: 525i/625i/525p/625p/750p/1125i/1125p(24/50/60)PCM 2ch

Audio Output 500mV (rms), Low impedance, RCA pin jack 2Headphone 3.5 mm stereo mini jack 1Remote Control Unit RM-C1932 (AA/R6 dry cell battery 2)

(No.YA604)1-3

SECTION 1PRECAUTION

1.1 SAFETY PRECAUTIONS(1) The design of this product contains special hardware,

many circuits and components specially for safetypurposes. For continued protection, no changes should bemade to the original design unless authorized in writing bythe manufacturer. Replacement parts must be identical tothose used in the original circuits. Service should beperformed by qualified personnel only.

(2) Alterations of the design or circuitry of the products shouldnot be made. Any design alterations or additions will voidthe manufacturer's warranty and will further relieve themanufacturer of responsibility for personal injury orproperty damage resulting therefrom.

(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. Thesecharacteristics are often not evident from visual inspectionnor can the protection afforded by them necessarily beobtained by using replacement components rated forhigher voltage, wattage, etc. Replacement parts whichhave these special safety characteristics are identified inthe parts list of Service manual. Electrical componentshaving such features are identified by shading on theschematics and by ( ) on the parts list in Servicemanual. The use of a substitute replacement which doesnot have the same safety characteristics as therecommended replacement part shown in the parts list ofService manual may cause shock, fire, or other hazards.

(4) Don't short between the LIVE side ground andISOLATED (NEUTRAL) side ground or EARTH sideground when repairing. Some model's power circuit is partly different in the GND.The difference of the GND is shown by the LIVE : ( ) sideGND, the ISOLATED (NEUTRAL) : ( ) side GND andEARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED(NEUTRAL) side GND or EARTH side GND and nevermeasure the LIVE side GND and ISOLATED (NEUTRAL)side GND or EARTH side GND at the same time with ameasuring apparatus (oscilloscope etc.). If above note willnot be kept, a fuse or any parts will be broken.

(5) When service is required, observe the original lead dress.Extra precaution should be given to assure correct leaddress in the high voltage circuit area. Where a short circuithas occurred, those components that indicate evidence ofoverheating should be replaced. Always use themanufacturer's replacement components.

(6) Isolation Check (Safety for Electrical Shock Hazard) After re-assembling the product, always perform anisolation check on the exposed metal parts of the cabinet(antenna terminals, video/audio input and output terminals,Control knobs, metal cabinet, screw heads, earphone jack,control shafts, etc.) to be sure the product is safe to operatewithout danger of electrical shock.

a) Dielectric Strength Test The isolation between the AC primary circuit and all metalparts exposed to the user, particularly any exposed metalpart having a return path to the chassis should withstand avoltage of 3000V AC (r.m.s.) for a period of one second. (.. . . Withstand a voltage of 1100V AC (r.m.s.) to anappliance rated up to 120V, and 3000V AC (r.m.s.) to anappliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generallyfound in the service trade.

b) Leakage Current Check Plug the AC line cord directly into the AC outlet (do not usea line isolation transformer during this check.). Using a"Leakage Current Tester", measure the leakage currentfrom each exposed metal part of the cabinet, particularlyany exposed metal part having a return path to the chassis,to a known good earth ground (water pipe, etc.). Anyleakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC(r.m.s.). Alternate Check Method

Plug the AC line cord directly into the AC outlet (do notuse a line isolation transformer during this check.). Usean AC voltmeter having 1000 per volt or moresensitivity in the following manner. Connect a 150010W resistor paralleled by a 0.15F AC-type capacitorbetween an exposed metal part and a known good earthground (water pipe, etc.). Measure the AC voltageacross the resistor with the AC voltmeter. Move theresistor connection to each exposed metal part,particularly any exposed metal part having a return pathto the chassis, and measure the AC voltage across theresistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Any voltage measured mustnot exceed 0.75V AC (r.m.s.). This corresponds to0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC(r.m.s.). This corresponds to 0.2mA AC (r.m.s.).

AC VOLTMETER

(HAVING 1000 /V,

OR MORE SENSITIVITY)

PLACE THIS PROBE

ON EACH EXPOSED

METAL PART1500 10W

0.15 F AC-TYPE

GOOD EARTH GROUND

1-4 (No.YA604)

1.2 INSTALLATION1.2.1 ATTACH THE STAND TO THE TVWhen installing the unit on the floor, it is required to attach thesupplied stand.To attach the stand to the TV, follow the procedure below.

To prevent scratches on the panel, lay a piece of soft cloth on aneven platform and place the TV onto it.

1.2.2 HEAT DISSIPATIONIf the heat dissipation vent behind this unit is blocked, coolingefficiency may deteriorate and temperature inside the unit willrise. The temperature sensor that protects the unit will beactivated when internal temperature exceeds the pre-determinedlevel and power will be turned off automatically.Therefore,please make sure pay attention not to block the heat dissipationvent as well as the ventilation outlet behind the unit and ensurethat there is room for ventilation around it.

1.2.3 INSTALLATION REQUIREMENTSEnsure that the minimal distance is maintained, as specifiedbelow, between the unit with and the surrounding walls, as wellas the floor etc.Install the unit on stable flooring or stands.Takeprecautionary measures to prevent the unit from tipping in orderto protect against accidents and earthquakes.

1.2.4 INSTALLATION REQUIREMENTSTo ensure safety in an emergency such as an earthquake, andto prevent accidents, ensure that measures are taken to preventthe TV dropping or falling over.

1.2.5 NOTES ON HANDLINGWhen taking the unit out of a packing case, do not grasp theupper part of the unit. If you take the unit out while grasping theupper part, the LCD PANEL may be damaged because of apressure. Instead of grasping the upper part, put your hands onthe lower backside or sides of the unit.

*The drawing may differ from the actual appearance.

VENTILATION HOLE

*The drawing may differ from the actual appearance.

200mm

50mm

150mm 150mm

50mm

It fixes in a band.

TV STAND

*The drawing may differ from the actual appearance.

(No.YA604)1-5

1.3 HANDLING LCD PANEL1.3.1 PRECAUTIONS FOR TRANSPORTATIONWhen transporting the unit, pressure exerted on the internal LCDpanel due to improper handling (such as tossing and dropping)may cause damages even when the unit is carefully packed. Toprevent accidents from occurring during transportation, paycareful attention before delivery, such as through explaining thehandling instructions to transporters.Ensure that the following requirements are met duringtransportation, as the LCD panel of this unit is made of glass andtherefore fragile:

(1) USE A SPECIAL PACKING CASE FOR THE LCD PANELWhen transporting the LCD panel of the unit, use a specialpacking case (packing materials). A special packing caseis used when a LCD panel is supplied as a service sparepart.

(2) ATTACH PROTECTION SHEET TO THE FRONTSince the front (display part) of the panel is vulnerable,attach the protection sheet to the front of the LCD panelbefore transportation. Protection sheet is used when a LCDpanel is supplied as a service spare part.

(3) AVOID VIBRATIONS AND IMPACTSThe unit may be broken if it is toppled sideways even whenproperly packed. Continuous vibration may shift the gap ofthe panel, and the unit may not be able to display imagesproperly. Ensure that the unit is carried by at least 2persons and pay careful attention not to exert any vibrationor impact on it.

(4) DO NOT PLACE EQUIPMENT HORIZONTALLYEnsure that it is placed upright and not horizontally duringtransportation and storage as the LCD panel is veryvulnerable to lateral impacts and may break. Duringtransportation, ensure that the unit is loaded along thetraveling direction of the vehicle, and avoid stacking themon one another. For storage, ensure that they are stackedin 2 layers or less even when placed upright.

1.3.2 OPTICAL FILTER (ON THE FRONT OF THE LCD PANEL)(1) Avoid placing the unit under direct sunlight over a

prolonged period of time. This may cause the optical filterto deteriorate in quality and colour.

(2) Clean the filter surface by wiping it softly and lightly with asoft and lightly fuzz cloth (such as outing flannel).

(3) Do not use solvents such as benzene or thinner to wipe thefilter surface. This may cause the filter to deteriorate inquality or the coating on the surface to come off. Whencleaning the filter, usually use the neutral detergent dilutedwith water. When cleaning the dirty filter, use water-dilutedethanol.

(4) Since the filter surface is fragile, do not scratch or hit it withhard materials. Be careful enough not to touch the frontsurface, especially when taking the unit out of the packingcase or during transportation.

1.3.3 PRECAUTIONS FOR REPLACEMENT OF EXTERIORPARTS

Take note of the following when replacing exterior parts (REARCOVER, FRONT PANEL, etc.):

(1) Do not exert pressure on the front of the LCD panel (filtersurface). It may cause irregular colour.

(2) Pay careful attention not to scratch or stain the front of theLCD panel (filter surface) with hands.

(3) When replacing exterior parts, the front (LCD panel) shouldbe placed facing downward. Place a mat, etc. underneathto avoid causing scratches to the front (filter surface).

1.3.4 HOW TO CHECK THE OPERATING TIME This model has a function to count and record the LCD paneloperating time. The operating time can be checked in thefollowing procedure. Maximum count time = 131072 hours

(1) Press the [INFORMATION] key and [MUTING] keysimultaneously, then enter the SERVICE MODE.

(2) Press the [2] key SELF CHECK MODE. (3) The operating time of the LCD panel is displayed in 6-digit

decimal number.(Refer to the below figure)

1.3.5 HOW TO RESET THE OPERATING TIMEWhen the LCD panel unit is replaced, be sure to reset theoperating time in the following method.

(1) Press the [INFORMATION] key and [MUTING] keysimultaneously, then enter the SERVICE MODE.

(2) Press the [9] key, then start the SHIPPING setting. (3) The power of the UNIT is turned off automatically, and the

OPERATING TIME is reset.

Press [2] key

Service Menu

1.Adjust2.Self Check3.I2C Stop

*When the power is turned off with the remote control unit or the power

button of the main unit, the count restarts from the turn off time.

*When the power is turned off by disconnecting the power cord from the

AC outlet, the recorded time count less than 2 hours is not counted.

The operating time is displayed.

SERVICE MODE SCREEN

SELF CHECK MODE SCREEN (Page 1)

Self Check

LOB 1

MEM 2 AIO 1

TUN 1 HDM 1

TOS 1

HOUR XXXXXX

Redkey2Page

i:EXIT

1-6 (No.YA604)

SECTION 2SPECIFIC SERVICE INSTRUCTIONS

2.1 FEATURESSUPER SLIM design

The screen surround itself is also very slim, so overall youhave a TV that takes up far less room and is much more like apicture frame.

FULL HDFull HD models deliver superbly detailed image reproduction ofmore than 2 megapixels (1920 x 1080), which represents doublethe resolution offered by WXGA panels.

HDMI INPUTBy connecting a HDMI compatible device, high definitionpictures can be displayed on your TV in their digital form.

DIGITAL VNRThis function cuts down the amount of noise in the originalpicture.

MaxxBassThis function emphasizes the bass sound.

3D Cinema SoundYou can enjoy sounds with a wider ambience.

2.2 MAIN DIFFERENCE LIST

2.3 21-PIN EURO CONNECTOR (SCART) : EXT-1 / EXT-2

(P-P= Peak to Peak, B-W= Blanking to white peak)

ITEMMODELS

LT-42S90B/B LT-42S90B/G LT-42S90B/L LT-42S90B/SPOWER CORD Round 2PIN type EU Type (2 Pins) Round 2PIN type UK 3PIN type

Pin No. Signal designation Matching value EXT-1 EXT-21 AUDIO R output 500mV(rms) (Nominal), Low impedance Used (TV OUT) Used (LINE OUT)2 AUDIO R input 500mV(rms) (Nominal), High impedance Used (R1) Used (R2)3 AUDIO L output 500mV(rms) (Nominal), Low impedance Used (TV OUT) Used (LINE OUT)4 AUDIO GND Used Used5 GND (B) Used Used6 AUDIO L input 500mV(rms) (Nominal), High impedance Used (L1) Used (L2)7 B input 700mV(B-W), 75 Used Not used 8 FUNCTION SW

(SLOW SW)Low : 0V-3VHigh : 8V-12V, High impedance

Used Used

9 GND (G) Used Used10 SCL Not used Used (SCL2)11 G input 700mV(B-W), 75 Used Not used 12 SDA Not used Used (SDA2)13 GND (R) Used Used14 GND (YS) Used Not used15 R / C input R : 700mV(B-W), 75

C : 300mV(P-P), 75Used (R) Used (C2)

16 Ys input (FAST SW) Low : 0V-0.4V, High : 1V-3V, 75 Used Not used 17 GND (VIDEO output) Used Used18 GND (VIDEO input) Used Used19 VIDEO output 1V(P-P) (Negative sync), 75 Used (TV OUT) Used (LINE OUT)20 VIDEO / Y input 1V(P-P) (Negative sync), 75 Used Used21 COMMON GND Used Used

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

[Pin assignment]

(No.YA604)1-7

2.4 TECHNICAL INFORMATION2.4.1 LCD PANELThis unit uses the flat type panel LCD (Liquid Crystal Display) panel that occupies as little space as possible, instead of theconventional CRT (Cathode Ray Tube), as a display unit.Since the unit has the two polarizing filter that are at right angles to each other, the unit adopts "normally black" mode, where lightdoes not pass through the polarizing filter and the screen is black when no voltage is applied to the liquid crystals.

2.4.1.1 SPECIFICATIONSThe following table shows the specifications of this unit.

2.4.1.2 PIXEL FAULTThere are three pixel faults - bright fault, dark fault and flicker fault - that are respectively defined as follows.

BRIGHT FAULTIn this pixel fault, a cell that should not light originally is lighting on and off.For checking this pixel fault, input ALL BLACK SCREEN and find out the cell that is lighting on and off.

DARK FAULTIn this pixel fault, a cell that should light originally is not lighting or lighting with the brightness twice as brighter as originally lighting.For checking this pixel fault, input 100% of each R/G/B colour and find out the cell that is not lighting.

FLICKER FAULTIn the pixel fault, a cell that should light originally or not light originally is flashing on and off.For checking this pixel fault, input ALL BLACK SCREEN signal or 100% of each RGB colour and find out the cell that is flashing onand off.

Item SpecificationsMaximum dimensions ( W H D ) 96.3 cm 55.6 cm 2.9 cm

Weight 11.0 kg

Effective screen size Diagonal: 106.7 cm (H: 93.0 cm V: 52.3 cm)

Aspect ratio 16 : 9

Drive device / system a-Si-TFT active matrix system

Resolution Horizontally 1920 Vertically 1080 RGB 6220800 dots in total

Pixel pitch (pixel size) Horizontally: 0.4845 mm, Vertically: 0.4845 mm

Displayed colour 16777216 colours 256 colours for R G and B

Brightness 500 cd/m2

Contrast ratio 1500 : 1

Response time 6.5 ms

View angle (Horizontally) 178

View angle (Vertically) 178

Surface polarizer Anti-Glare type Low reflective coat

Colour filter Vertical stripe

Backlight Cold cathode fluorescent lamp 22

Power supply voltage in LCD 12 V

Power supply voltage in inverter 24 V

Panel interface system LVDS (Low Voltage Differential Signaling)

1-8 (No.YA604)

2.4.2 MAIN CPU PIN FUNCTION [IC7001 : MAIN PWB]Pin Pin name I/O Function 1 KEY1 I Key scan for side control (POWER/VOL/UP/DOWN)2 ECO SENSER I Eco sensor detection3 VDD33_GPIO - 3.3V power supply4 SLOW1 I EXT-1 SLOW detection5 SLOW2 I EXT-2 SLOW detection6 AFC1 I AFT voltage for VHF/UHF tuner7 AGC I RF AGC voltage for VHF/UHF tuner8 GND - GND9 VDD33_CADC - 3.3V power supply10 MONITOR_OUT O Video for EXT-211 VDD33_AFE - 3.3V power supply12 VOUT2 O Not used13 VDD12_ADC_1234 - 1.25V power supply14 VOUT3 O Not used15 GND - GND16 TV_CV I Video for VHF/UHF tuner17 GND - GND18 E1_CV I Video for EXT-119 VDD12_ADC_1234 - 1.25V power supply20 E2_CV/Y I Video/Y for EXT-221 GND - GND22 AGND1234 I LPF setting23 VDD33_AFE - 3.3V power supply24 IDTV_CV I Not used25 VDD12_ADC_1234 - 1.25V power supply26 IDTV_CR I Cr for digital tuner27 GND - GND28 IDTV_Y I Y for digital tuner29 GND - GND30 SC_FB1 I Ys for EXT-131 VDD12_ADC_1234 - 1.25V power supply32 IDTV_CB I Not used33 GND - GND34 SC_R1 I R for EXT-135 VDD33_AREF - 3.3V power supply36 SC_G1 I G for EXT-137 VDD12_ADC_5678 - 1.25V power supply38 SC_B1 I B for EXT-139 GND - GND40 AGND5678 I LPF setting41 GND - GND42 E2_C I C for EXT-243 VDD12_ADC_5678 - 1.25V power supply44 VIN16 I Not used45 GND - GND46 VIN17 I Not used47 VDD33_AREF - 3.3V power supply48 VIN18 I Not used49 VDD12_ADC_5678 - 1.25V power supply50 E3_PR I Pr for EXT-351 GND - GND52 E3_Y I Y for EXT-353 GND - GND54 E3_PB I Pb for EXT-355 VDD12_ADC_5678 - 1.25V power supply56 VIN22 I Not used57 GND - GND58 VDD_CORE - 1V power supply59 GND - GND60 SIF_INM I SIF for VHF/UHF tuner61 TU_SIF I SIF for VHF/UHF tuner62 VDD12_SIFADC - 1.25V power supply63 LINE_OUT1R O Audio for EXT-164 LINE_OUT1L O Audio for EXT-165 TU_R O Audio for EXT-2 or Audio66 TU_L O Audio for EXT-2 or Audio67 R_AUSW I Audio68 L_AUSW I Audio69 VDD33_AAU - 3.3V power supply

70 LINE_IN3R I Not used71 LINE_IN3L I Not used72 GND - GND73 LINE_IN2R I Not used74 LINE_IN2L I Not used75 GND - GND76 LINE_IN1R I Not used77 LINE_IN1L I Not used78 VREFAU I Reference voltage setting79 HP_R O Audio for headphone80 HP_L O Audio for headphone81 MAIN_OUT_SUB O Not used82 M_R O Audio for speaker83 M_L O Audio for speaker84 GND - GND85 VDD10_HDMI1+2 - 1V power supply86 HMDI1_RXCN I TMDS clock for HDMI87 HMDI1_RXCP I TMDS clock for HDMI88 GND - GND89 VDD33_HDMI1+2 - 3.3V power supply90 HDMI1_RX0N I TMDS data for HDMI91 HDMI1_RX0P I TMDS data for HDMI92 GND - GND93 VDD10_HDMI1+2 - 1V power supply94 HDMI1_RX1N I TMDS data for HDMI95 HDMI1_RX1P I TMDS data for HDMI96 GND - GND97 VDD33_HDMI1+2 - 3.3V power supply98 HDMI1_RX2N I TMDS data for HDMI99 HDMI1_RX2P I TMDS data for HDMI

100 GND - GND101 VDD10_HDMI1+2 - 1V power supply102 VDD_CORE - 1V power supply103 GND - GND104 VDD10_HDMI1+2 - 1V power supply105 HMDI2_RXCN I Not used106 HMDI2_RXCP I Not used107 GND - GND108 VDD33_HDMI1+2 - 3.3V power supply109 HDMI2_RX0N I Not used110 HDMI2_RX0P I Not used111 GND - GND112 VDD10_HDMI1+2 - 1V power supply113 HDMI2_RX1N I Not used114 HDMI2_RX1P I Not used115 GND - GND116 VDD33_HDMI1+2 - 3.3V power supply117 HDMI2_RX2N I Not used118 HDMI2_RX2P I Not used119 GND - GND120 VDD10_HDMI1+2 - 1V power supply121 VDD25_DRAM - 2.5V power supply122 DRAM_VREF I Reference voltage setting123 VDD25_DRAM - 2.5V power supply124 VDD25_DRAM - 2.5V power supply125 VDD25_DRAM - 2.5V power supply126 RX_DTV O Not used127 DIN_HOTP1 O Hotplug error detection for HDMI connector-1 [Error = L]128 AUDIO_MUTE O Speaker/headphone output muting [Muting = H]129 VDD33_GPIO - 3.3V power supply130 LB_PRO I Power abnormality detection [Emergent = H]131 P3.2 I L fixed132 HM_SDA I/O Data for I2C bus (for HDMI)133 HM_SCL O Clock for I2C bus (for HDMI)134 HM_HPLUG2 O Hotplug error detection for HDMI connector-2 [Error = L]135 HM_HPLUG3 O Hotplug error detection for HDMI connector-3 [Error = L]136 STATUS I Not used137 ID_RESET O Not used138 IRQ O Not used

Pin Pin name I/O Function

(No.YA604)1-9

139 TX_DTV I Not used140 P4.6 I/O Not used141 P4.7 I/O Not used142 BL_ON O Power on/off control for back-light [ON = L]143 LCD_POW O Power on/off control for LCD drive [ON = H]144 VDD33_VIPA - 3.3V power supply145 TV_LINK_IN I Not used146 TV LINK_OUT O Not used147 P2.4 I/O Not used148 P2.5 I/O Not used149 P2.6 I/O Not used150 P2.7 I/O Not used151 NC I L fixed152 NC I L fixed153 NC - GND154 NC I L fixed155 P3.0 I L fixed156 P3.1 I L fixed157 NC I L fixed158 VDD33_VIPA - 3.3V power supply159 NC I L fixed160 NC I L fixed161 NC I L fixed162 VDD33_VIPA - 3.3V power supply163 NC I L fixed164 NC I L fixed165 NC I L fixed166 SDA0 I/O Data for I2C bus (for E2PROM)167 SCL0 O Clock for I2C bus (for E2PROM)168 PFC O Power on/off control for PFC [ON = L]169 MAIN_POWER O Power on/off control for main power [ON = L]170 VDD - 1V power supply171 TCLK I Clock for JTAG interface172 TDI I Data for JTAG interface173 TDO O Data for JTAG interface174 TMS I Control signal for JTAG interface175 GND - GND176 GND - GND177 GND - GND178 GND - GND179 GND - GND180 GND - GND181 VDD33_DAU - 3.3V power supply182 NC - Not used183 NC I L fixed184 NC I L fixed185 NC I L fixed186 NC - Not used187 NC - Not used188 PWM_DIM O PWM dimming control for back-light inverter189 VDD25_PIP - 2.5V power supply190 DC_DIM O Not used: DC dimming control for back-light inverter191 PCS6 O Not used192 PCS5 O Not used193 VDD25_PIP - 2.5V power supply194 PCS4 O Not used195 PCS3 O Not used196 VDD25_PIP - 2.5V power supply197 PCS2 O Not used198 PCS1 O Not used199 VDD25_DRAM - 2.5V power supply200 VDD25_DRAM - 2.5V power supply201 VDD25_DRAM - 2.5V power supply202 VDD10_DLL - 1V power supply203 VDD25_DRAM - 2.5V power supply204 TE2+ O LVDS data for LCD panel205 TE2- O LVDS data for LCD panel206 VDD25_VOPA - 2.5V power supply207 TD2+ O LVDS data for LCD panel208 TD2- O LVDS data for LCD panel

Pin Pin name I/O Function 209 GND - GND210 TCLK2+ O LVDS clock for LCD panel211 TCLK2- O LVDS clock for LCD panel212 VDD25_VOPA - 2.5V power supply213 TC2+ O LVDS data for LCD panel214 TC2- O LVDS data for LCD panel215 GND - GND216 TB2+ O LVDS data for LCD panel217 TB2- O LVDS data for LCD panel218 VDD25_VOPA - 2.5V power supply219 TA2+ O LVDS data for LCD panel220 TA2- O LVDS data for LCD panel221 GND - GND222 GND - GND223 VDD25_PLL - 2.5V power supply224 VDD33_FLASH - 3.3V power supply225 VDD10_PLL - 1V power supply226 TE1+ O LVDS data for LCD panel227 TE1- O LVDS data for LCD panel228 VDD25_VOPA - 2.5V power supply229 TD1+ O LVDS data for LCD panel230 TD1- O LVDS data for LCD panel231 GND - GND232 TCLK1+ O LVDS clock for LCD panel233 TCLK1- O LVDS clock for LCD panel234 VDD25_VOPA - 2.5V power supply235 TC1+ O LVDS data for LCD panel236 TC1- O LVDS data for LCD panel237 GND - GND238 TB1+ O LVDS data for LCD panel239 TB1- O LVDS data for LCD panel240 VDD25_VOPA - 2.5V power supply241 TA1+ O LVDS data for LCD panel242 TA1- O LVDS data for LCD panel243 VDD_CORE - 1V power supply244 VSENSE I Not used245 VDD10 - 1V power supply246 GND - GND247 XTALIN I X'tal oscillation for CPU system clock 248 XTALOUT O X'tal oscillation for CPU system clock 249 VDD33_GPIO - 3.3V power supply250 RESET I CPU reset [Reset = L]251 SDA1 I/O Data for I2C bus (for tuner/MaxxBass)252 SCL1 O Clock for I2C bus (for tuner/MaxxBass)253 VDD33_STDB - 3.3V power supply254 VDD10_STDB - 1V power supply255 REMOCON I Remote control sensor256 HM_POWER I Power status detect for HDMI

Pin Pin name I/O Function

1-10 (No.YA604)

SECTION 3DISASSEMBLY

3.1 CAUTION AT DISASSEMBLY Make sure that the power cord is disconnected from the outlet. Pay special attention not to break or damage the parts. Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors. Be sure to reattach the wire clamps removed during the procedure to the original positions. (Attaching the wire clamps in wrong

positions may affect the performance.)

REFERENCE:When removing each board, remove the connector if necessary. The operation is easier if you write down the connection points(connector numbers) of the connector. For connection of each board, refer to the "WIRING DIAGRAM" of the Standard CircuitDiagram.

3.2 DISASSEMBLY PROCEDURE3.2.1 REMOVING THE REAR COVER (Fig.3-1)

(1) Remove the 1 screw [A].(2) Remove the STAND COVER.(3) Remove the 1 screw [B].(4) Remove the POWER CORD COVER.(5) Remove the POWER CORD.(6) Remove the JACK COVER.(7) Remove the 2 hooks [a], 10 screws [C], 5 screws [D], 5

screws [E] and 1 screw [F].(8) Remove the REAR COVER.

3.2.2 REMOVING THE POWER UNIT (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER. Remove the POWER CORD.

(1) Remove the 6 screws [G].(2) Remove the POWER UNIT.

3.2.3 REMOVING THE MAIN PWB (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER.

(1) Remove the 1 screw [H].(2) Remove the TERMINAL BASE.(3) Remove the 7 screws [J].(4) Remove the MAIN PWB.

3.2.4 REMOVING THE CAPSENS PWB (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER.

(1) Remove the CAPSENS PWB by carefully peeling off thedouble faced tape.

3.2.5 REMOVING THE IR PWB (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER.

(1) Remove the 1 screw [M].(2) Remove the IR PWB.

3.2.6 REMOVING THE HP/USB PWB (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER.

(1) Remove the 1 screw [N].(2) Remove the HP/USB PWB.

3.2.7 REMOVING THE LED PWB, LED LENS (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER.

(1) Remove the 1 screw [P].(2) Remove the LED PWB.(3) Remove the LED LENS.

3.2.8 REMOVING THE SPEAKER (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER.

(1) Remove the 4 screws [Q].(2) Remove the SPEAKER HOLDER.(3) Remove the 4 screws [R].(4) Remove the SPEAKER.

3.2.9 REMOVING THE STAND ASSY (Fig.3-1) Remove the STAND COVER.

(1) Remove the 4 screws [S].(2) Remove the STAND.

3.2.10 REMOVING THE LCD PANEL UNIT (Fig.3-1) Remove the STAND COVER. Remove the REAR COVER. Remove the STAND.

(1) Remove the 3 screws [T] and 2 screws [U].(2) Remove the STAND SUPPORT.(3) Remove the 8 screws [V].(4) Remove the BACK BRACKET.(5) Remove the 4 screws [W].(6) Remove the MAIN BASE.(7) Remove the 6 screws [X].(8) Slide the SIDE BRACKET in the direction of the arrow to

remove it.(9) Remove the 4 screws [Y].

(10) Slide the TOP BRACKET in the direction of the arrow toremove it.

(11) Lift up the LCD PANEL UNIT to remove it.

(No.YA604)1-11

Fig.3-1

FRONT

STAND COVER

X

Y

Y

X

X

X

RR

M

N

P

T

U

H

S

V

W

V

V

W

G J

C

D

B

D

C

F

E

STAND

JACK COVER

REAR COVER

POWER CORDPOWER CORD COVER

POWER UNIT

MAIN PWB

TERMINAL BASE

MAIN BASE

FRONT PANEL

TOP BRACKET

LED PWB

TOP BRACKET

BACK

BRACKET

BACK

BRACKET

LED LENS

CAPSENS PWB

IR PWB

SIDE BRACKET

SPEAKER

HP/USB PWB

STAND SUPPORT

STAND

SUPPORT

Q

U

Q

T

SIDE BRACKETSPEAKER HOLDER

A

aa

aa

1-12 (No.YA604)

3.2.11 REMOVING THE LCD CONTROL PWB (Fig.3-2) Remove the STAND COVER. Remove the REAR COVER. Remove the MAIN BASE.

(1) Remove the 4 screws [A].(2) Remove the LCD CONTROL PWB COVER.(3) Remove the LCD CONTROL PWB.

3.2.12 REMOVING THE INVERTER PWB (Fig.3-2) Remove the STAND COVER. Remove the REAR COVER. Remove the SIDE BRACKET.

(1) Remove the 6 screws [B].(2) Remove the INVERTER PWB COVER.(3) Remove the INVERTER PWB.(4) Follow the same steps when removing the other

INVERTER PWB.

Fig.3-2

INVERTER PWB COVER

INVERTER PWB COVER

LCD CONTROL PWB COVER

LCD CONTROL PWB

INVERTER PWB (SLAVE)

INVERTER PWB (MASTER)LCD PANEL UNIT

BB

BB

AA

(No.YA604)1-13

3.3 MEMORY IC REPLACEMENT This model uses the memory IC. This memory IC stores data for proper operation of the video and drive circuits. When replacing, be sure to use an IC containing this (initial value) data.

3.3.1 MEMORY IC TABLE

3.3.2 MEMORY IC REPLACEMENT PROCEDURE1. Power off

Switch off the power and disconnect the power plug from the AC outlet.

2. Replace the memory ICBe sure to use the memory IC written with the initial setting values.

3. Power onConnect the power plug to the AC outlet and switch on the power.

4. Receiving channel settingRefer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.

5. User settingCheck the user setting items according to the given in page later. Where these do not agree, refer to the OPERATINGINSTRUCTIONS and set the items as described.

6. SERVICE MODE settingVerify what to set in the SERVICE MODE, and set whatever is necessary (Fig.3-3). Refer to the SERVICE ADJUSTMENT forsetting.

3.3.3 SERVICE MODE SETTINGSERVICE MODE SCREEN

Fig.3-3

SETTING ITEM

Symbol Number of pins Mounting PWB Main content of dataIC7003 8-pin MAIN PWB Setting value of IC7001(MAIN CPU) is memorized.

SERVICE MODE SCREEN

ADJUST MODE SCREEN

Service Menu

1.Adjust2.Self Check3.I2C Stop

Press [1] key

Adjust PAL BG

1.SC ADJ 15SC DEV : +00

OK:Store i:Exit

Setting mode Setting items Settings1.ADJUST 1.SC ADJ. Adjust

2.R DRIVE Adjust

3.G DRIVE Adjust

4.B DRIVE Adjust

5.CUTOFF R Fixed [Do not adjust]

6.CUTOFF G Fixed [Do not adjust]

7.CUTOFF B Fixed [Do not adjust]

8.COLOUR Fixed [Do not adjust]

9.HUE Fixed [Do not adjust]

10.CONT. Fixed [Do not adjust]

11.BRIGHT2 Fixed [Do not adjust]

12.SHARP Fixed [Do not adjust]

13.CORING Fixed [Do not adjust]

1-14 (No.YA604)

3.3.4 SETTINGS OF FACTORY SHIPMENT3.3.4.1 BUTTON OPERATION 3.3.4.2 REMOTE CONTROL DIRECT OPERATION

3.3.4.3 REMOTE CONTROL MENU OPERATION(1) PICTURE

(2) SOUND

(3) FEATURES

(4) SET UP

Setting item Setting positionPOWER OffCHANNEL PR1VOLUME 10TV/AV TV

Setting item Setting positionCHANNEL PR1VOLUME 10ZOOM AutoSUB POWER OffVIDEO-3 COMPONENT / COMPOSITE Component

Setting item Setting positionPicture Mode BrightColour Temp. CoolFEATURESDigital VNR RF Auto

OTHER OnDigiPure OnMovie Theatre OffColour Management OnPicture Management OnSmart Picture OnDynamic Backlight OnMPEG Noise Reduction OnColour System TV Depends on PR/CH

EXT Auto4:3 Auto Aspect Panoramic

Setting item Setting positionSTEREO / III Stereo soundBass CentreTreble CentreBalance CentreHyper Sound OffMaxxBass Low3D CINEMA SOUNDSorrund MidBass Boost MidAuto Volume Control Off

Setting item Setting positionSleep Timer OffChild Lock Off (ID:0000)Blue Back OnFavourite Setting BlankPower Lamp OnEco Sensor Off

Setting item Setting positionAuto Program TV Channel Automatically SetEdit / manual Preset Ch OnlyLanguage EnglishExt Setting Ext-1HDMI-1 Audio Setting Auto

(No.YA604)1-15

3.4 REPLACEMENT OF CHIP COMPONENT3.4.1 CAUTIONS

(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern.(3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.

3.4.2 SOLDERING IRON(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.

3.4.3 REPLACEMENT STEPS 1. How to remove Chip parts

[Resistors, capacitors, etc.]

(1) As shown in the figure, push the part with tweezers andalternately melt the solder at each end.

(2) Shift with the tweezers and remove the chip part.

[Transistors, diodes, variable resistors, etc.]

(1) Apply extra solder to each lead.

(2) As shown in the figure, push the part with tweezers andalternately melt the solder at each lead. Shift and removethe chip part.

NOTE :After removing the part, remove remaining solder from thepattern.

2. How to install Chip parts

[Resistors, capacitors, etc.]

(1) Apply solder to the pattern as indicated in the figure.

(2) Grasp the chip part with tweezers and place it on thesolder. Then heat and melt the solder at both ends of thechip part.

[Transistors, diodes, variable resistors, etc.]

(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the

solder. (3) First solder lead A as indicated in the figure.

(4) Then solder leads B and C.

SOLDER SOLDER

A

B

C

A

B

C

1-16 (No.YA604)

SECTION 4ADJUSTMENT

4.1 ADJUSTMENT PREPARATION(1) This TV is adjusted by using REMOTE CONTROL UNIT.(2) The adjustment using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values

which adjust the screen to the optimum condition can be different from the initial setting values.(3) Make sure that connection is correctly made AC to AC power source.(4) Turn on the power of the TV and measuring instruments for warming up for at least 30 minutes before starting adjustments.(5) If the receive or input signal is not specified, use the most appropriate signal for adjustment.(6) Never touch the parts (such as variable resistors, transformers and condensers) not shown in the adjustment items of this service

adjustment.

4.2 PRESET SETTING BEFORE ADJUSTMENTSUnless otherwise specified in the adjustment items, preset thefollowing functions with the REMOTE CONTROL UNIT.

4.3 MEASURING INSTRUMENT AND FIXTURES Signal generator (Pattern generator)[PAL] Remote control unit

4.4 ADJUSTMENT ITEMS VIDEO CIRCUIT

COLOUR DECODER adjustment WHITE BALANCE (HIGH LIGHT) adjustment

4.5 BASIC OPERATION OF SERVICE MODE4.5.1 HOW TO ENTER THE SERVICE MODE

(1) Press [INFORMATION] key and [MUTING] key on theremote control unit simultaneously to enter the SERVICEMODE SCREEN.

NOTE:Before entering the SERVICE MODE, confirm that the settingof TV/STB/DVD/AUDIO mode is at the "TV" side. If theswitches have not been properly set, you cannot enter theSERVICE MODE.

4.5.2 HOW TO EXIT THE SERVICE MODEPress the [MENU] key to exit the Service mode.

4.5.3 CHANGE AND MEMORY OF SETTING VALUESELECTION OF SETTING ITEM

[FUNCTION /] key.For scrolling up / down the setting items.

CHANGE OF SETTING VALUE (DATA) [FUNCTION /] key.

For scrolling up / down the setting values.

MEMORY OF SETTING VALUE (DATA)Changed setting value is memorized by pressing [OK] key.

4.5.4 SERVICE MODE SELECT KEY LOCATION

Setting item Settings positionPICTURE MODE STANDARD

PICTURE adjustments Centre

COLOUR TEMP. NORMAL

Colour Management Off

Picture Management Off

Smart Picture Off

Dynamic Backlight Off

Eco Sensor Off

Service Menu

1.Adjust2.Self Check3.I2C Stop

SERVICE MODE SCREEN

NOT USEDRefer to SECTION5

INFORMATION

MUTING

OKFUNCTION

/

FUNCTION

/

(No.YA604)1-17

4.5.5 ADJUSTMENT MODEThis mode is used to adjust the VIDEO CIRCUIT.

4.5.5.1 HOW TO ENTER THE ADJUSTMENT MODEWhen the SERVICE MENU SCREEN of SERVICE MODE isdisplayed, press [1] key to enter the ADJUSTMENT MODE.NOTE:

When a number key other than the [1] key is pressed in theSERVICE MODE SCREEN, the other relevant screen maybe displayed.This is not used in the adjustment procedure. Press the[MENU] key to return to the SERVICE MODE SCREEN.

4.5.5.2 DESCRIPTION OF STATUS DISPLAY

(1) SIGNAL SYSTEMThe signal displayed on the screen is displayed.

(2) SETTING ITEM NAMESetting item name are displayed. The setting item numbers tobe displayed are listed below.

(3) SETTING VALUE (DATA)The SETTING VALUE is displayed.

Adjust 576 50i

2.R DRIVE XXXX

OK:Store i:Exit

Service Menu

1.Adjust2.Self Check3.I2C Stop

Press [1] key

(1) SIGNAL SYSTEM

(3) SETTING VALUE (DATA)(2) SETTING ITEM

SERVICE MODE SCREEN

ADJUST MODE SCREEN

480 60i : 480i (Component) / HDMI 480i576 50i : 576i (Component) / HDMI 576i480 60p : 480p (Component) / HDMI 480p480 60p VGA : HDMI 480p VGA576 50p : 576p (Component) / HDMI 576p720 50p : 720p 50Hz (Component) / HDMI 720p 50Hz720 60p : 720p 60Hz (Component) / HDMI 720p 60Hz1080 60i : 1080i 60Hz (Component) / HDMI 1080i 60Hz1080 50i : 1080i 50Hz (Component) / HDMI 1080i 50Hz1080 60p : 1080p 60Hz (Component) / HDMI 1080p 60Hz1080 50p : 1080p 50Hz (Component) / HDMI 1080p 50Hz1080 24p : HDMI 1080p 24HzPAL BG : PAL 50Hz(Composite / S-video)SECAM : SECAMNTSC3.58 : NTSC3.58NTSC4.43 : NTSC4.43PAL 60 : PAL 60Hz(Composite / S-video)PAL M : PAL MPAL N : PAL NRGB 480i : RGB 480iRGB 576i : RGB 576iUndefined : Other than those above

Setting mode Setting items Settings1.ADJUST 1.SC ADJ. Adjust

2.R DRIVE Adjust

3.G DRIVE Adjust

4.B DRIVE Adjust

5.CUTOFF R Fixed [Do not adjust]

6.CUTOFF G Fixed [Do not adjust]

7.CUTOFF B Fixed [Do not adjust]

8.COLOUR Fixed [Do not adjust]

9.HUE Fixed [Do not adjust]

10.CONT. Fixed [Do not adjust]

11.BRIGHT2 Fixed [Do not adjust]

12.SHARP Fixed [Do not adjust]

13.CORING Fixed [Do not adjust]

1-18 (No.YA604)

4.6 INITIAL SETTING VALUES IN THE SERVICE MODE Perform fine-tuning based on the "initial values" using the remote control when in the Service mode. The "initial values" serve only as an indication rough standard and therefore the values with which optimal display can be achieved

may be different from the default values. Never change the values of the items ( ) that are not described in ADJUSTMENT PROCEDURE or in the below table as they

are fixed values.

Item name Variable range Setting value

1.SC ADJ. 0 - 63 192.R DRIVE 0 - 1024 5123.G DRIVE 0 - 1024 4914.B DRIVE 0 - 1024 5125.CUTOFF R -1024 - 1023 06.CUTOFF G -1024 - 1023 07.CUTOFF B -1024 - 1023 0

Item name Variable rangeSetting value

PAL (EXT) PAL (RF) SECAM (EXT) SECAM (RF)8.COLOUR 0 - 256 132 145 98 989.HUE -64 - 64 -2 -4 -2 -510.CONTRAST 0 - 256 140 140 140 14011.BRIGHT-2 -1024 - 1023 -3 -11 -3 -11

Item name Variable range

Setting valueNTSC_M / NTSC4.43 RGB

Component / HDMI

8.COLOUR 0 - 256 127 140 1309.HUE -64 - 64 -3 -4 -410.CONTRAST 0 - 256 135 140 11811.BRIGHT-2 -1024 - 1023 -15 -3 -23

Item name Variable range

Setting valueCONPOSITE_50Hz /

S-VIDEO_50HzPAL (RF) / SECAM

(RF)CONPOSITE_60Hz /

S-VIDEO_60Hz NTSC_RF RGB 480i

12.SHARP 0 - 63 32 32 37 32 3213.CORING 0 - 63 5 5 5 0 2

Item name Variable rangeSetting value

RGB 576i TEXT TWIN12.SHARP 0 - 63 32 3213.CORING 0 - 63 2 0

Item name Variable range

Setting value

Component 480i Component 576i Component 480p Component 576p Component 720p50 / Component 1080i5012.SHARP 0 - 63 35 35 35 35 3713.CORING 0 - 63 2 2 2 2 2

Item name Variable range

Setting valueComponent 720p60 / Component 1080i60

Component 1080p50

Component 1080p60

Component 1080i50 / Component 1080p50

Component 1080i60 / Component 1080p60

12.SHARP 0 - 63 37 37 37 37 3713.CORING 0 - 63 2 2 2 2 2

(No.YA604)1-19

4.7 ADJUSTMENT PROCEDURE4.7.1 VIDEO CIRCUIT

Item name Variable range

Setting value

HDMI 480i HDMI 576i HDMI 480p HDMI 576p HDMI 720p50 / HDMI 1080i5012.SHARP 0 - 63 35 35 35 35 38

13.CORING 0 - 63 2 2 2 2 2

Item name Variable range

Setting value

HDMI 1080p50 HDMI 1080p60 HDMI 1080i50 / HDMI 1080p50HDMI 1080i60 / HDMI 1080p60 HDMI 1080p24

12.SHARP 0 - 63 38 38 38 38 38

13.CORING 0 - 63 2 2 2 2 2

Item Measuring instrument Test point Adjustment part Description

COLOURDECODER

Remote control unit

Signalgenerator

[1.ADJUST]1.SC ADJ

(1) Receive a PAL colour bar signal.(2) Select "1.ADJUST" from the SERVICE MODE.(3) Select .(4) Adjust the value of to set the value

of (A) to 03.NOTE:

The value of should be adjustedwithin 7 - 24.

(5) Press the [OK] key to memorize the set value.

WHITE BALANCE (HIGHLIGHT)

Remote control unit

Signalgenerator

[1.ADJUST]2.R DRIVE3.G DRIVE4.B DRIVE

(1) Receive a PAL 75% all white signal.(2) Set PICTURE MODE to "STANDARD".(3) Set ZOOM to "FULL".(4) Set COLOUR TEMP. to "NORMAL".(5) Select "1.ADJUST" from the SERVICE MODE.(6) Adjustment is select 1 item from ,

and then select itemfix to "512" Other color shold be less than 920.

NOTE:Finaly minimam more than 1 item (, or )should be "512".

(7) Must check white balance adjustment correctrywith low light to high light.

(8) Press the [OK] key to memorize the set value.

Adjust PAL BG

1.SC ADJ 15SC DEV : +00

OK:Store i:Exit

(A)

1-20 (No.YA604)

SECTION 5TROUBLESHOOTING

5.1 SELF CHECK FEATURE5.1.1 OUTLINEThis unit comes with the "Self check" feature, which checks theoperational state of the circuit and displays/saves it duringfailure.Diagnosis is performed when power is turned on, andinformation input to the main microcomputer is monitored at alltime.Diagnosis is displayed in 2 ways via screen display and LEDflashes. Failure detection is based on input state of I2C bus andthe various control lines connected to the main microcomputer.

5.1.2 HOW TO ENTER THE SELF CHECK MODEBefore enter the SELF CHECK MODE, press the [MODE] key toconfirm that "TV" position is indicated. If it is in a wrong position,the SELF CHECK MODE operation cannot be performed.

(1) Press the [INFORMATION] key and [MUTING] keysimultaneously, then enter the SERVICE MODE.

(2) Press the [2] key SELF CHECK MODE. (3) Press the [RED] key to enter Page 2 of the SELF CHECK

MODE.*Use the [GREEN] key to toggle between Page 1 and Page 2.

NOTE:When a number key other than the [2] key is pressed in theSERVICE MODE screen, the other relevant screen may bedisplayed.This is not used in the SELF CHECK MODE. Press the[MENU] key to return to the MAIN MENU SCREEN.

5.1.3 HOW TO EXIT THE SELF CHECK MODETo Save Failure History:Turn off the power by unplugging the AC power cord plug whenin the Self check display mode.To Clear (Reset) Failure History: Turn off the power by pressing the [POWER] key on the remotecontrol unit when in the Self check display mode.

5.1.4 FAILURE HISTORYFailure history can be counted up to 9 times for each item. Whenthe number exceeds 9, display will remain as 9. Failure historywill be stored in the memory unless it has been deleted.

NOTE:Only SYN (with/without sync signals) will be neither countednor stored.

5.1.5 POINTS TO NOTE WHEN USING THE SELF CHECKFEATURE

In addition to circuit failures (abnormal operation), the followingcases may also be diagnosed as "Abnormal" and counted.

(1) Temporary defective transmissions across circuits due topulse interruptions.

(2) Misalignment in the on/off timing of power for I2C bus (Vcc)when turning on/off the main power.

Therefore, turn on the main power, and then wait for about 3seconds before starting Self check. If recurrences are expected, ensure to clear (reset) the failurehistory and record the new diagnosis results.

Fig.5-1

Press [2] key

Press [Green] key

Press [Red] key

Service Menu

1.Adjust2.Self Check3.I2C Stop

SERVICE MODE SCREEN

SELF CHECK MODE SCREEN (Page 1)

SELF CHECK MODE SCREEN (Page 2)

Self Check

LOB 1

MEM 2 AIO 1

TUN 1 HDM 1

TOS 1

HOUR XXXXXX

Redkey2Page

i:EXIT

Self Check

SYN OK CDN 00

ADS 00 ADH 00

PPL 600 LPF 137 INT 0 FMT 00

FMD FF

Greenkey1Page

i:EXIT

Item

Item

Failure history

Failure history

NOT USED

Refer to SECTION1

DiagnosisOK:NormalNG:Abnormal

(No.YA604)1-21

5.1.6 DETAILSSelf check is performed for the following items:

indicates items not used for services as they are for designing.

5.1.7 METHOD OF DISPLAY WHEN A RASTER IS NOT OUTPUTIn the state where a raster is not output by breakdown of the set, an error is displayed by blink of the POWER LED.

< Explanation of operation >If error is detected, the power is turned off. Shortly after the power is turned off, POWER LED will be blinked.When the protection of low bias line short operates, the power cannot be turned on until the power cord takes out and inserts, afterthe power is turned off.

Detection item Display Detection content Diagnosis signal (line) Detection timing

Low bias line short protection

LOB Confirm the operation of the low bais(1V/3.3V/5V)protection circuit.1V: Q9351 [MAIN PWB]3.3V: Q9601 [MAIN PWB]5V: Q9201 [MAIN PWB]

LB_PRO Detection starts 5 seconds afterthe power is turned on. If errorcontinues between 200 ms thepower is turned off.

MAIN MEMORY MEM Confirmation of reply of ACK signal which usesI2C communication.IC7003 [MAIN PWB]

SDA If it checks whenever I2Ccommunication is performed andno reply of ACK signal an errorwill be counted.

AUDIO AIO Confirmation of reply of ACK signal which usesI2C communication.IC6661 [MAIN PWB]

SDA If it checks whenever I2Ccommunication is performed andno reply of ACK signal an errorwill be counted.

RF (ANALOG) TUNER TUN Confirmation of reply of ACK signal which usesI2C communication.TU1001 [MAIN PWB]

SDA If it checks whenever I2Ccommunication is performed andno reply of ACK signal an errorwill be counted.

HDMI HDM Confirmation of the internal determinationprocessing of HDMI.IC8501 [MAIN PWB]

--- When an excessive load hangs tothe interrupt to the internaldetermination of HDMI, an errorwill be counted.

TOUCH SENSOR TOS Count how many times to reset the touch sensorcircuit.IC7701 [CAPSENS PWB]

XRES The number of times the mainCPU outputs reset signal iscounted according to an error ofthe touch sensor circuit.

Detection item Display Detection content Detection timingSYNC SIGNAL SYN Confirmation of presence of sync signal in

selected video signal.IC7001 [MAIN PWB]

The selected video input signal is always checked and if there is the sync signal, it is displayed as "OK", and if not as "NG".

For designing CDN - -For designing ADS - -For designing ADH - -For designing PPL - -For designing LPF - -For designing INT - -For designing FMT - -

Type of error POWER LED flash cycleLow bias line short protection Blue turnig on and off at 1 second intervals.

(No.YA604)

VPTPrinted in Japan

Victor Company of Japan, LimitedDisplay category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan

(No.YA604)3-1

PARTS LISTCAUTIONJ The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the

safety.

J The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied.J P.W. BOARD Ass'y will not be supplied, but those which are filled with the Parts No. in the Parts No. columns will be supplied.

ABBREVIATIONS OF RESISTORS, CAPACITORS AND TOLERANCES

RESISTORS CAPACITORS

CR Carbon Resistor C CAP. Ceramic Capacitor

FR Fusible Resistor E CAP. Electrolytic Capacitor

PR Plate Resistor M CAP. Mylar Capacitor

VR Variable Resistor CH CAP. Chip Capacitor

HV R High Voltage Resistor HV CAP. High Voltage Capacitor

MF R Metal Film Resistor MF CAP. Metalized Film Capacitor

MG R Metal Glazed Resistor MM CAP. Metalized Mylar Capacitor

MP R Metal Plate Resistor MP CAP. Metalized Polystyrol Capacitor

OM R Metal Oxide Film Resistor PP CAP. Polypropylene Capacitor

CMF R Coating Metal Film Resistor PS CAP. Polystyrol Capacitor

UNF R Non-Flammable Resistor TF CAP. Thin Film Capacitor

CH V R Chip Variable Resistor MPP CAP. Metalized Polypropylene Capacitor

CH MG R Chip Metal Glazed Resistor TAN. CAP. Tantalum Capacitor

COMP. R Composition Resistor CH C CAP. Chip Ceramic Capacitor

LPTC R Linear Positive Temperature Coefficient Resistor BP E CAP. Bi-Polar Electrolytic Capacitor

CH AL E CAP. Chip Aluminum Electrolytic Capacitor

CH AL BP CAP. Chip Aluminum Bi-Polar Capacitor

CH TAN. E CAP. Chip Tantalum Electrolytic Capacitor

CH AL BP E CAP. Chip Tantalum Bi-Polar Electrolytic Capacitor

RESISTORS

F G J K M N R H Z P

1% 2% 5% 10% 20% 30% +30%-10%+50%-10%

+80%-20%

+100%-0%

3-2(No.YA604)

CONTENTSUSING P.W. BOARD & REMOTE CONTROL UNIT ................................................................................................... 3-2EXPLODED VIEW PARTS LIST -1 ............................................................................................................................. 3-3EXPLODED VIEW -1 ................................................................................................................................................... 3-4EXPLODED VIEW PARTS LIST -2 ............................................................................................................................. 3-5EXPLODED VIEW -2 ................................................................................................................................................... 3-5

PRINTED WIRING BOARD PARTS LIST [LT-42S90B/B] ......................................................................................... 3-6MAIN P.W. BOARD ASS'Y (SFT-1106A-BK) .................................................................................................... 3-6HP/USB P.W. BOARD ASS'Y (SFT-7303A-BK) .............................................................................................. 3-10CAPSENS P.W. BOARD ASS'Y (SFT-7701A-BK) .......................................................................................... 3-11LED P.W. BOARD ASS'Y (SFT-8701A-BK) .................................................................................................... 3-11IR P.W. BOARD ASS'Y (SFT-8801A-BK) ........................................................................................................ 3-11

PRINTED WIRING BOARD PARTS LIST [LT-42S90B/G,LT-42S90B/S,LT-42S90B/L] ......................................... 3-12MAIN P.W. BOARD ASS'Y (SFT-1106A-H2) ................................................................................................... 3-12HP/USB P.W. BOARD ASS'Y (SFT-7303A-H2) .............................................................................................. 3-16CAPSENS P.W. BOARD ASS'Y (SFT-7701A-H2) .......................................................................................... 3-17LED P.W. BOARD ASS'Y (SFT-8701A-H2) ..................................................................................................... 3-17IR P.W. BOARD ASS'Y (SFT-8801A-H2) ........................................................................................................ 3-17

REMOTE CONTROL UNIT PARTS LIST (RM-C1932-1C) ....................................................................................... 3-18PACKING ................................................................................................................................................................... 3-18PACKING PARTS LIST ............................................................................................................................................. 3-18

USING P.W. BOARD & REMOTE CONTROL UNIT

P.W.B ASS'Y nameP.W.B ASS'Y No.

LT-42S90B/B LT-42S90B/G LT-42S90B/S LT-42S90B/L

MAIN P.W.B SFT-1106A-BK SFT-1106A-H2

HP/USB P.W.B SFT-7303A-BK SFT-7303A-H2

CAPSENS P.W.B SFT-7701A-BK SFT-7701A-H2

LED P.W.B SFT-8701A-BK SFT-8701A-H2

IP P.W.B SFT-8801A-BK SFT-8801A-H2

REMOTE CONTROL UNIT RM-C1932-1C

(No.YA604)3-3

EXPLODED VIEW PARTS LIST -1 Ref.No. Part No. Part Name Description Local

1 LC13434-002C-H REAR COVER 2 LC13477-002B-0K FRONT PANEL

4 WJW0085-001A-E DIGITAL(LVDS) CABLE MAIN PWB CN0LV1 - LCD PANEL UNIT 5 QAS0554-001 SPEAKER (x2) 7 QMPRA90-165-Q1 POWER CORD 1.65m BLACK LT-42S90BB 7 QMPRB50-170-Q1 POWER CORD 1.7m BLACK LT-42S90BG,LT-42S90BL 7 QMPN370-170-JC POWER CORD 1.7m BLACK LT-42S90BS

8 LC13438-001B-H TERMINAL BASE 9 LC13436-001A-C MAIN BASE 10 LC43038-001A-C SIDE BRACKET (x6) 11 LC34362-001A-C BACK BRACKET (x4) 14 LC43085-001B-C STAND SUPPORT(L) LT-42S90BB,LT-42S90BL 14 LC43085-001A-C STAND SUPPORT(L) LT-42S90BG,LT-42S90BS 15 LC43085-002B-C STAND SUPPORT(R) LT-42S90BB,LT-42S90BL 15 LC43085-002A-C STAND SUPPORT(R) LT-42S90BG,LT-42S90BS 16 LC43042-001A-C STAND BASE 17 LC43084-001C-C STAND SHAFT LT-42S90BB,LT-42S90BL 17 LC43084-001A-C STAND SHAFT LT-42S90BG,LT-42S90BS 20 LC13492-001A-HK POWER CORD COVER LT-42S90BB,LT-42S90BS,LT-42S90BL 20 LC13492-001A-H POWER CORD COVER LT-42S90BG

24 LC34304-001A-C TOP BRACKET(L) 25 LC34305-001A-C TOP BRACKET(R) 30 LC34307-001A-C SPEAKER HOLDER (x2) 32 LC34360-001B LED LENS 35 LC13435-001A-H JACK COVER 51 QYSPSPD3008MA SCREW M3 x 8mm(x10) 52 QYSBSFG4012MA TAP SCREW M4 x 12mm(x5) 53 QYSBSF3012MA TAP SCREW M3 x 12mm 54 LC42784-003A SCREW (x5) 55 QYSBSFG4012MA TAP SCREW M4 x 12mm 56 QQR0491-001 FERRITE CORE 58 LC34361-001A JACK SHEET 59 LC34406-002A TERMINAL SHEET 60 QYSSSP5016ZA SCREW M5 x 16mm(x5) 61 WJJ0942-001A-E WIRE MAIN PWB CN10LR - SPEAKER 62 QZW0375-001 EDGING (x2) 64 LC42784-002A SCREW 65 QZW0156-002 WIRE CLAMP (x3) 67 WJZ0311-001A-E WIRE POWER UNIT - MAIN PWB 68 WJJ0845-005B-E WIRE POWER UNIT CN104 - LCD PANEL UNIT 69 WJS0097-001A-E WIRE POWER UNIT CN103 - LCD PANEL UNIT 71 LC34373-002A WIRE GUIDE (x2) 73 LC34092-035A-C STICK SHEET 74 GG40069-002A-H W FACE TAPE 75 WJZ0310-001A-E WIRE MAIN PWB - CAPSENS PWB / IR PWB / HP/USB PWB / LED PWB

200 QAL1086-001 POWER UNIT 202 SFT-1106A-BK MAIN PWB LT-42S90BB 202 SFT-1106A-H2 MAIN PWB LT-42S90BG,LT-42S90BS,LT-42S90BL

204 SFT-8701A-BK LED PWB LT-42S90BB 204 SFT-8701A-H2 LED PWB LT-42S90BG,LT-42S90BS,LT-42S90BL

209 SFT-7701A-BK CAPSENS PWB LT-42S90BB 209 SFT-7701A-H2 CAPSENS PWB LT-42S90BG,LT-42S90BS,LT-42S90BL

210 SFT-8801A-BK IR PWB LT-42S90BB 210 SFT-8801A-H2 IR PWB LT-42S90BG,LT-42S90BS,LT-42S90BL

211 SFT-7303A-BK HP/USB PWB LT-42S90BB 211 SFT-7303A-H2 HP/USB PWB LT-42S90BG,LT-42S90BS,LT-42S90BL

3-4(No.YA604)

EXPLODED VIEW -1

FRONT

STAND COVER

52

54

59

53

35

20

56

54

15

14

2

25

10

10

11

9

8

65

11

11

5

30

74

75

20910

24

64

202

468

1

51

51

557

16

17

60

58

62

61

67

69

65

62

65

71

71

10

211

210

204

32

73

RATING LABEL

LCD PANEL UNIT

200

(No.YA604)3-5

EXPLODED VIEW PARTS LIST -2

EXPLODED VIEW -2

Ref.No. Part No. Part Name Description Local

3 QLD0547-001-JET LCD PANEL UNIT Inc. 3A-3B LT-42S90BB,LT-42S90BL 3 QLD0547-001-JMT LCD PANEL UNIT Inc. 3A-3B LT-42S90BG,LT-42S90BS 3A 55.42T02.008 LCD CONTROL PWB 3A or 55.42T02.C02 LCD CONTROL PWB 3B QLL0187-001-25 INVERTER PWB 2pcs in 1set

INVERTER PWB COVER

INVERTER PWB COVER

LCD CONTROL PWB COVER

3B3B

3B3B

3A3A

33

3-6(No.YA604)

PRINTED WIRING BOARD PARTS LIST [LT-42S90B/B] MAIN P.W. BOARD ASS'Y (SFT-1106A-BK)

Ref No. Part No. Part Name Description Local

IC1001 MM1510XN-X ICIC1002 MM1510XN-X ICIC1003 NJW1110V-X ICIC1004 NJM4565M-WE ICIC6001 TPA3101D2PHP-W ICIC6011 BH3547F-X ICIC6661 MX3000DS-X ICIC6771 NJM4565M-WE ICIC7002 S-80928CLNB-G-W ICIC7003 ATF256-42S90BB IC (SERVICE)IC7004 M62320GP1-X ICIC7005 M62320GP1-X ICIC8001 ATF02-42DR9BJA1 IC (SERVICE)IC8101 ATF02-42DR9BJA2 IC (SERVICE)IC8201 ATF02-42DR9BJA3 IC (SERVICE)IC8501 TMDS351PAG ICIC9151 PQ1MGX38MS-X ICIC9201 SI-8005Q-X ICIC9251 SI-8008TM-X ICIC9351 SI-8015Q-X ICIC9511 S7809D-W ICIC9601 SI-8005Q-X ICIC9651 MM1662FH-X ICIC9751 PQ1MGX38MS-X IC

Q1003 2SC1623A/5-6/-X TRANSISTORQ1004 2SC1623A/5-6/-X TRANSISTORQ1005 2SC1623A/5-6/-X TRANSISTORQ1101 2SA812A/5-6/-X TRANSISTORQ1102 RT4N430C-X DIGI TRANSISTORQ1103 RT4N430C-X DIGI TRANSISTORQ1201 2SA812A/5-6/-X TRANSISTORQ1202 RT4N430C-X DIGI TRANSISTORQ1203 RT4N430C-X DIGI TRANSISTORQ1204 2SC1623A/5-6/-X TRANSISTORQ1205 2SC1623A/5-6/-X TRANSISTORQ1301 2SA812A/5-6/-X TRANSISTORQ1302 RT4N430C-X DIGI TRANSISTORQ1303 RT4N430C-X DIGI TRANSISTORQ6105 RT1N441C-X TRANSISTORQ6106 2SC1623A/5-6/-X TRANSISTORQ6501 2SA812A/5-6/-X TRANSISTORQ6502 2SA812A/5-6/-X TRANSISTORQ6503 RT4N430C-X DIGI TRANSISTORQ7001 RT1P441C-X DIGI TRANSISTORQ7003 RT1P441C-X DIGI TRANSISTORQ7004 RT1P441C-X DIGI TRANSISTORQ7006 2SC1623A/5-6/-X TRANSISTORQ7008 2SC1623A/5-6/-X TRANSISTORQ7009 2SK3019-X MOS FETQ7010 2SK3019-X MOS FETQ7011 2SC1623A/5-6/-X TRANSISTORQ7013 RT1N441C-X TRANSISTORQ7014 2SC1623A/5-6/-X TRANSISTORQ7019 RT1N441C-X TRANSISTORQ8001 RT1P441C-X DIGI TRANSISTORQ8002 RT1N441C-X TRANSISTORQ8004 RT1N441C-X TRANSISTORQ8101 RT1P441C-X DIGI TRANSISTORQ8102 RT1N441C-X TRANSISTORQ8201 RT1P441C-X DIGI TRANSISTORQ8202 RT1N441C-X TRANSISTORQ9201 2SC1623A/5-6/-X TRANSISTORQ9351 2SC1623A/5-6/-X TRANSISTORQ9601 2SC1623A/5-6/-X TRANSISTOR

D1101 UDZW5.6B-X Z DIODED1102 UDZW3.6B-X Z DIODED1103 UDZW8.2B-X Z DIODED1104 UDZW8.2B-X Z DIODED1105 UDZW3.6B-X Z DIODED1106 UDZW3.6B-X Z DIODED1107 UDZW3.6B-X Z DIODED1108 UDZW3.6B-X Z DIODED1109 UDZW3.6B-X Z DIODED1110 UDZW3.6B-X Z DIODED1111 UDZW8.2B-X Z DIODED1112 UDZW8.2B-X Z DIODED1113 UDZW5.6B-X Z DIODED1202 UDZW3.6B-X Z DIODED1203 UDZW5.6B-X Z DIODED1204 UDZW5.6B-X Z DIODED1205 UDZW8.2B-X Z DIODED1206 UDZW8.2B-X Z DIODED1209 MA111-X SI DIODE

D1210 UDZW8.2B-X Z DIODED1211 UDZW8.2B-X Z DIODED1217 UDZW3.6B-X Z DIODED1301 UDZW8.2B-X Z DIODED1302 UDZW8.2B-X Z DIODED1303 UDZW8.2B-X Z DIODED1304 UDZW8.2B-X Z DIODED1307 UDZW3.6B-X Z DIODED1308 UDZW3.6B-X Z DIODED1309 UDZW3.6B-X Z DIODED6101 MA111-X SI DIODED6104 MA111-X SI DIODED6501 MA111-X SI DIODED6502 MA111-X SI DIODED6503 MA111-X SI DIODED6771 UDZW6.2B-X Z DIODED7006 UDZW5.6B-X Z DIODED7007 UDZW5.6B-X Z DIODED7008 UDZW5.6B-X Z DIODED7009 UDZW5.6B-X Z DIODED7010 UDZW5.6B-X Z DIODED7011 UDZW5.6B-X Z DIODED7012 UDZW5.6B-X Z DIODED7013 UDZW5.6B-X Z DIODED7014 UDZW5.6B-X Z DIODED7019 UDZW8.2B-X Z DIODED7020 UDZW5.6B-X Z DIODED8001 MA111-X SI DIODED8002 MA111-X SI DIODED8101 MA111-X SI DIODED8102 MA111-X SI DIODED8201 MA111-X SI DIODED8202 MA111-X SI DIODED9201 RB055L-40-X SB DIODED9202 RB055L-40-X SB DIODED9203 PTZ6.8B-X Z DIODED9204 MA111-X SI DIODED9206 UDZW3.0B-X Z DIODED9251 RB055L-40-X SB DIODED9252 RB055L-40-X SB DIODED9253 PTZ3.9B-X Z DIODED9351 RB055L-40-X SB DIODED9352 RB055L-40-X SB DIODED9353 PTZ3.9B-X Z DIODED9354 MA111-X SI DIODED9601 RB055L-40-X SB DIODED9602 RB055L-40-X SB DIODED9603 PTZ3.9B-X Z DIODED9605 MA111-X SI DIODE

C1001 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1002 NEHL1AM-107X E CAPACITOR 100uF 10V MC1006 NCB31AK-105X C CAPACITOR 1uF 10V KC1007 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1008 NEHL1HM-106X E CAPACITOR 10uF 50V MC1009 NEHL1EM-106X E CAPACITOR 10uF 25V MC1010 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1011 NCB31HK-821X C CAPACITOR 820pF 50V KC1012 NDC31HJ-470X C CAPACITOR 47pF 50V JC1013 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1014 NDC31HJ-470X C CAPACITOR 47pF 50V JC1015 NDC31HJ-180X C CAPACITOR 18pF 50V JC1016 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1017 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1101 NEHL1CM-106X E CAPACITOR 10uF 16V MC1102 NEHL1AM-107X E CAPACITOR 100uF 10V MC1103 NEHL1CM-106X E CAPACITOR 10uF 16V MC1104 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1105 NCB31AK-105X C CAPACITOR 1uF 10V KC1107 NCB31HK-472X C CAPACITOR 4700pF 50V KC1110 NCB31HK-472X C CAPACITOR 4700pF 50V KC1111 NCB31HK-472X C CAPACITOR 4700pF 50V KC1112 NCB31HK-472X C CAPACITOR 4700pF 50V KC1113 NEHL1CM-106X E CAPACITOR 10uF 16V MC1114 NEHL1CM-106X E CAPACITOR 10uF 16V MC1115 NCB31AK-105X C CAPACITOR 1uF 10V KC1116 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1117 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1118 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1119 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1120 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1121 NCB31AK-105X C CAPACITOR 1uF 10V KC1122 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1123 NCJ21CK-106X-D C CAPACITOR 10uF 16V KC1124 NCB31HK-222X C CAPACITOR 2200pF 50V KC1125 NCB21AK-475X C CAPACITOR 4.7uF 10V KC1126 NCJ21CK-106X-D C CAPACITOR 10uF 16V K

Ref No. Part No. Part Name Description Local

(No.YA604)3-7

C1127 NDC31HJ-100X C CAPACITOR 10pF 50V JC1128 NDC31HJ-100X C CAPACITOR 10pF 50V JC1129 NCB31HK-222X C CAPACITOR 2200pF 50V KC1130 NCB21AK-475X C CAPACITOR 4.7uF 10V KC1201 NEHL1CM-106X E CAPACITOR 10uF 16V MC1202 NEHL1AM-107X E CAPACITOR 100uF 10V MC1203 NEHL1CM-106X E CAPACITOR 10uF 16V MC1204 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1205 NCB31AK-105X C CAPACITOR 1uF 10V KC1207 NCB31HK-472X C CAPACITOR 4700pF 50V KC1208 NCB31HK-152X C CAPACITOR 1500pF 50V KC1209 NCB31HK-152X C CAPACITOR 1500pF 50V KC1210 NCB31HK-472X C CAPACITOR 4700pF 50V KC1211 NCB31HK-472X C CAPACITOR 4700pF 50V KC1212 NCB31HK-472X C CAPACITOR 4700pF 50V KC1213 NEHL1CM-106X E CAPACITOR 10uF 16V MC1214 NEHL1CM-106X E CAPACITOR 10uF 16V MC1215 NCB31AK-105X C CAPACITOR 1uF 10V KC1216 NCB31AK-105X C CAPACITOR 1uF 10V KC1217 NCB31AK-105X C CAPACITOR 1uF 10V KC1218 NCB31AK-105X C CAPACITOR 1uF 10V KC1223 NEHL1CM-476X E CAPACITOR 47uF 16V MC1224 NCB20JK-106X C CAPACITOR 10uF 6.3V KC1225 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1226 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1301 NCB31HK-472X C CAPACITOR 4700pF 50V KC1302 NCB31HK-472X C CAPACITOR 4700pF 50V KC1303 NCB31HK-472X C CAPACITOR 4700pF 50V KC1304 NCB31HK-472X C CAPACITOR 4700pF 50V KC1305 NEHL1CM-106X E CAPACITOR 10uF 16V MC1306 NEHL1CM-106X E CAPACITOR 10uF 16V MC1307 NCB31AK-105X C CAPACITOR 1uF 10V KC1308 NCB31AK-105X C CAPACITOR 1uF 10V KC1312 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1314 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1315 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1403 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1404 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1405 NCB31HK-104X C CAPACITOR 0.1uF 50V KC1406 NCB31HK-104X C CAPACITOR 0.1uF 50V KC6011 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6012 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6102 NCB31HK-103X C CAPACITOR 0.01uF 50V KC6103 NCB31HK-103X C CAPACITOR 0.01uF 50V KC6104 NCB31CK-105X C CAPACITOR 1uF 16V KC6105 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6106 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6107 NCB31CK-105X C CAPACITOR 1uF 16V KC6108 NCB31HK-103X C CAPACITOR 0.01uF 50V KC6109 NCB31CK-105X C CAPACITOR 1uF 16V KC6110 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6111 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6112 NCB21EK-334X C CAPACITOR 0.33uF 25V KC6113 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6114 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6115 NCB31CK-105X C CAPACITOR 1uF 16V KC6116 QEHQ1HM-227 E CAPACITOR 220uF 50V MC6117 NCB31CK-105X C CAPACITOR 1uF 16V KC6118 NCB31CK-105X C CAPACITOR 1uF 16V KC6119 QEHQ1HM-227 E CAPACITOR 220uF 50V MC6120 NCB31CK-105X C CAPACITOR 1uF 16V KC6121 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6122 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6123 NCB21EK-334X C CAPACITOR 0.33uF 25V KC6124 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6125 NCB31CK-224X C CAPACITOR 0.22uF 16V KC6126 NCB31CK-105X C CAPACITOR 1uF 16V KC6127 NEHL1CM-106X E CAPACITOR 10uF 16V MC6128 NCB21AK-225X C CAPACITOR 2.2uF 10V KC6501 NEHL1CM-107X E CAPACITOR 100uF 16V MC6502 NRSA63J-0R0X MG RESISTOR 0 1/16W JC6503 NRSA63J-0R0X MG RESISTOR 0 1/16W JC6504 NCB31HK-222X C CAPACITOR 2200pF 50V KC6505 NCB31HK-222X C CAPACITOR 2200pF 50V KC6506 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6507 NEHL1AM-107X E CAPACITOR 100uF 10V MC6508 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6509 NCJ21CK-475X-R C CAPACITOR 4.7uF 16V KC6510 NEHL0GM-227X E CAPACITOR 220uF 4V MC6511 NEHL1CM-476X E CAPACITOR 47uF 16V MC6512 NEHL0GM-227X E CAPACITOR 220uF 4V MC6513 NCB31HK-104X C CAPACITOR 0.1uF 50V KC6514 NCB31HK-104X C CAPACITOR 0.1uF 50V KC6671 NCB21AK-225X C CAPACITOR 2.2uF 10V KC6672 NCB21AK-225X C CAPACITOR 2.2uF 10V KC6673 NDC31HJ-330X C CAPACITOR 33pF 50V JC6674 NDC31HJ-330X C CAPACITOR 33pF 50V JC6675 NEHL1CM-106X E CAPACITOR 10uF 16V MC6676 NCB31HK-104X C CAPACITOR 0.1uF 50V KC6677 NCB31CK-105X C CAPACITOR 1uF 16V K

Ref No. Part No. Part Name Description Local

C6678 NCB31HK-153X C CAPACITOR 0.015uF 50V KC6679 NDC31HJ-330X C CAPACITOR 33pF 50V JC6680 NDC31HJ-330X C CAPACITOR 33pF 50V JC6681 NEHL1CM-106X E CAPACITOR 10uF 16V MC6682 NCB31HK-104X C CAPACITOR 0.1uF 50V KC6685 NCB31HK-104X C CAPACITOR 0.1uF 50V KC6771 NCB31CK-105X C CAPACITOR 1uF 16V KC6772 NCB31CK-105X C CAPACITOR 1uF 16V KC6773 NCB21AK-225X C CAPACITOR 2.2uF 10V KC6774 NCB31AK-474X C CAPACITOR 0.47uF 10V KC6775 NEHL1CM-476X E CAPACITOR 47uF 16V MC7001 NCB31HK-103X C CAPACITOR 0.01uF 50V KC7002 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7003 NCB31AK-334X C CAPACITOR 0.33uF 10V KC7004 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7005 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7006 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7007 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7008 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7009 NCB31HK-103X C CAPACITOR 0.01uF 50V KC7010 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7011 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7012 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7013 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7014 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7015 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7016 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7017 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7019 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7020 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7021 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7022 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7023 NDC31HJ-560X C CAPACITOR 56pF 50V JC7024 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7025 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7026 NCB31HK-472X C CAPACITOR 4700pF 50V KC7028 NCB31HK-472X C CAPACITOR 4700pF 50V KC7029 NCB31HK-472X C CAPACITOR 4700pF 50V KC7030 NCB31HK-472X C CAPACITOR 4700pF 50V KC7031 NDC31HJ-560X C CAPACITOR 56pF 50V JC7032 NCB11AK-106X C CAPACITOR 10uF 10V KC7033 NCB11AK-106X C CAPACITOR 10uF 10V KC7034 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7035 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7036 NCB11AK-475X C CAPACITOR 4.7uF 10V KC7037 NCB31HK-472X C CAPACITOR 4700pF 50V KC7038 NCB31HK-472X C CAPACITOR 4700pF 50V KC7039 NCB31HK-472X C CAPACITOR 4700pF 50V KC7040 NCB31HK-472X C CAPACITOR 4700pF 50V KC7041 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7042 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7043 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7044 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7045 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7046 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7047 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7048 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7049 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7050 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7051 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7052 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7053 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7054 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7055 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7056 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7057 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7058 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7059 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7060 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7061 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7062 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7063 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7064 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7065 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7066 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7067 NCB31AK-105X C CAPACITOR 1uF 10V KC7068 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7070 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7074 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7075 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7076 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7077 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7078 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7079 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7080 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7081 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7082 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7083 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7084 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7085 NCB20JK-106X C CAPACITOR 10uF 6.3V K

Ref No. Part No. Part Name Description Local

3-8(No.YA604)

C7086 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7087 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7089 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7090 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7091 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7092 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7093 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7094 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7095 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7096 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7097 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7098 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7099 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7100 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7101 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7102 NCB31HK-103X C CAPACITOR 0.01uF 50V KC7103 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7104 NDC31HJ-120X C CAPACITOR 12pF 50V JC7105 NDC31HJ-120X C CAPACITOR 12pF 50V JC7106 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7107 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7108 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7109 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7110 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7111 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7112 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7113 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7117 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7119 NCB31CK-105X C CAPACITOR 1uF 16V KC7120 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7121 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7122 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7123 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7124 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7125 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7126 NCB20JK-106X C CAPACITOR 10uF 6.3V KC7127 NCB31HK-104X C CAPACITOR 0.1uF 50V KC7128 NCB31AK-105X C CAPACITOR 1uF 10V KC7130 NEHL1CM-106X E CAPACITOR 10uF 16V MC7132 NCB31CK-105X C CAPACITOR 1uF 16V KC8001 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8002 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8003 NDC31HJ-101X C CAPACITOR 100pF 50V JC8101 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8102 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8103 NDC31HJ-101X C CAPACITOR 100pF 50V JC8201 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8202 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8203 NDC31HJ-101X C CAPACITOR 100pF 50V JC8501 NCB20JK-106X C CAPACITOR 10uF 6.3V KC8502 NCB11AK-106X C CAPACITOR 10uF 10V KC8503 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8504 NCB31HK-103X C CAPACITOR 0.01uF 50V KC8505 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8506 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8507 NCB31HK-103X C CAPACITOR 0.01uF 50V KC8508 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8509 NCB31HK-103X C CAPACITOR 0.01uF 50V KC8510 NCB31HK-104X C CAPACITOR 0.1uF 50V KC8511 NCB31HK-103X C CAPACITOR 0.01uF 50V KC9151 NCB31AK-105X C CAPACITOR 1uF 10V KC9152 NEHM1CM-106X E CAPACITOR 10uF 16V MC9153 NCB31AK-334X C CAPACITOR 0.33uF 10V KC9155 NCB20JK-106X C CAPACITOR 10uF 6.3V KC9156 NCB20JK-106X C CAPACITOR 10uF 6.3V KC9201 NCJ41HK-335X-U C CAPACITOR 3.3uF 50V KC9203 NCJ41CM-226X-U C CAPACITOR 22uF 16V MC9204 NCJ41CM-226X-U C CAPACITOR 22uF 16V MC9205 NCB31HK-222X C CAPACITOR 2200pF 50V KC9206 NCB31HK-332X C CAPACITOR 3300pF 50V KC9208 NCB31HK-103X C CAPACITOR 0.01uF 50V KC9209 NCB31HK-223X C CAPACITOR 0.022uF 50V KC9210 NEHM1HM-105X E CAPACITOR 1uF 50V MC9251 NEHM0GM-227X E CAPACITOR 220uF 4V MC9254 NEHM0GM-227X E CAPACITOR 220uF 4V MC9257 NEHM0GM-227X E CAPACITOR 220uF 4V MC9258 NCB20JK-106X C CAPACITOR 10uF 6.3V KC9352 NCJ41HK-335X-U C CAPACITOR 3.3uF 50V KC9353 NCJ41CM-226X-U C CAPACITOR 22uF 16V MC9354 NCJ41CM-226X-U C CAPACITOR 22uF 16V MC9355 NCB31HK-103X C CAPACITOR 0.01uF 50V KC9356 NCB31HK-104X C CAPACITOR 0.1uF 50V KC9357 NDC31HJ-101X C CAPACITOR 100pF 50V JC9358 NCB31HK-103X C CAPACITOR 0.01uF 50V KC9360 NCJ41CM-226X-U C CAPACITOR 22uF 16V MC9511 NEHM1EM-336X E CAPACITOR 33uF 25V MC9512 NEHM1EM-336X E CAPACITOR 33uF 25V MC9602 NCJ41HK-335X-U C CAPACITOR 3.3uF 50V KC9603 NCJ41CM-226X-U C CAPACITOR 22uF 16V MC9604 NCJ41CM-226X-U C CAPACITOR 22uF 16V M

Ref No. Part No. Part Name Description Local

C9605 NCB31HK-103X C CAPACITOR 0.01uF 50V KC9606 NCB31HK-223X C CAPACITOR 0.022uF 50V KC9607 NDC31HJ-101X C CAPACITOR 100pF 50V JC9608 NCB31HK-103X C CAPACITOR 0.01uF 50V KC9651 NCB31CK-105X C CAPACITOR 1uF 16V KC9652 NEHM1CM-106X E CAPACITOR 10uF 16V MC9653 NCB31AK-334X C CAPACITOR 0.33uF 10V KC9654 NDC31HJ-471X C CAPACITOR 470pF 50V JC9655 NCB31AK-105X C CAPACITOR 1uF 10V KC9751 NCB31AK-105X C CAPACITOR 1uF 10V KC9753 NEHM1CM-106X E CAPACITOR 10uF 16V MC9754 NCB31AK-334X C CAPACITOR 0.33uF 10V KC9755 NCB20JK-106X C CAPACITOR 10uF 6.3V KC9756 NCB20JK-106X C CAPACITOR 10uF 6.3V KC9757 NCB31AK-474X C CAPACITOR 0.47uF 10V KC9758 NCB31AK-474X C CAPACITOR 0.47uF 10V K

R1002 NRSA63J-101X MG RESISTOR 100 1/16W JR1003 NRSA63J-101X MG RESISTOR 100 1/16W JR1004 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1009 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1010 NRSA63J-681X MG RESISTOR 680 1/16W JR1011 NRSA63J-102X MG RESISTOR 1k 1/16W JR1012 NRSA63J-102X MG RESISTOR 1k 1/16W JR1013 NRSA63J-331X MG RESISTOR 330 1/16W JR1014 NRSA63J-181X MG RESISTOR 180 1/16W JR1015 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1016 NRSA63J-102X MG RESISTOR 1k 1/16W JR1017 NRSA63J-271X MG RESISTOR 270 1/16W JR1018 NRSA63J-470X MG RESISTOR 47 1/16W JR1019 NRSA63J-271X MG RESISTOR 270 1/16W JR1020 NRSA63J-102X MG RESISTOR 1k 1/16W JR1021 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1022 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1101 NRSA63J-750X MG RESISTOR 75 1/16W JR1102 NRSA63J-750X MG RESISTOR 75 1/16W JR1103 NRSA63J-750X MG RESISTOR 75 1/16W JR1104 NRSA63J-750X MG RESISTOR 75 1/16W JR1105 NRSA63J-750X MG RESISTOR 75 1/16W JR1106 NRSA63J-183X MG RESISTOR 18k 1/16W JR1107 NRSA63J-123X MG RESISTOR 12k 1/16W JR1108 NRSA63J-750X MG RESISTOR 75 1/16W JR1109 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1110 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1111 NRSA63J-391X MG RESISTOR 390 1/16W JR1112 NRSA63J-391X MG RESISTOR 390 1/16W JR1113 NRSA63J-333X MG RESISTOR 33k 1/16W JR1114 NRSA63J-333X MG RESISTOR 33k 1/16W JR1115 NRSA63J-823X MG RESISTOR 82k 1/16W JR1116 NRSA63J-823X MG RESISTOR 82k 1/16W JR1117 NRSA63J-104X MG RESISTOR 100k 1/16W JR1118 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR1119 NRSA63J-182X MG RESISTOR 1.8k 1/16W JR1120 NRSA63J-223X MG RESISTOR 22k 1/16W JR1121 NRSA63J-562X MG RESISTOR 5.6k 1/16W JR1122 NRSA63J-104X MG RESISTOR 100k 1/16W JR1123 NRSA63J-473X MG RESISTOR 47k 1/16W JR1124 NRSA63J-473X MG RESISTOR 47k 1/16W JR1125 NRSA63J-104X MG RESISTOR 100k 1/16W JR1126 NRSA63J-473X MG RESISTOR 47k 1/16W JR1127 NRSA63J-473X MG RESISTOR 47k 1/16W JR1128 NRSA63J-223X MG RESISTOR 22k 1/16W JR1201 NRSA63J-750X MG RESISTOR 75 1/16W JR1202 NRSA63J-750X MG RESISTOR 75 1/16W JR1203 NRSA63J-750X MG RESISTOR 75 1/16W JR1206 NRSA63J-183X MG RESISTOR 18k 1/16W JR1207 NRSA63J-123X MG RESISTOR 12k 1/16W JR1209 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1210 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1211 NRSA63J-391X MG RESISTOR 390 1/16W JR1212 NRSA63J-391X MG RESISTOR 390 1/16W JR1213 NRSA63J-333X MG RESISTOR 33k 1/16W JR1214 NRSA63J-333X MG RESISTOR 33k 1/16W JR1215 NRSA63J-823X MG RESISTOR 82k 1/16W JR1216 NRSA63J-823X MG RESISTOR 82k 1/16W JR1217 NRSA63J-104X MG RESISTOR 100k 1/16W JR1218 NRSA63J-103X MG RESISTOR 10k 1/16W JR1219 NRSA63J-103X MG RESISTOR 10k 1/16W JR1220 NRSA63J-102X MG RESISTOR 1k 1/16W JR1223 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1226 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1236 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR1238 NRSA63J-101X MG RESISTOR 100 1/16W JR1239 NRSA63J-101X MG RESISTOR 100 1/16W JR1301 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1302 NRSA63J-333X MG RESISTOR 33k 1/16W JR1303 NRSA63J-222X MG RESISTOR 2.2k 1/16W JR1304 NRSA63J-333X MG RESISTOR 33k 1/16W JR1306 NRSA63J-750X MG RESISTOR 75 1/16W JR1308 NRSA63J-750X MG RESISTOR 75 1/16W J

Ref No. Part No. Part Name Description Local

(No.YA604)3-9

R1310 NRSA63J-750X MG RESISTOR 75 1/16W JR1311 NRSA63J-823X MG RESISTOR 82k 1/16W JR1312 NRSA63J-823X MG RESISTOR 82k 1/16W JR1313 NRSA63J-391X MG RESISTOR 390 1/16W JR1314 NRSA63J-391X MG RESISTOR 390 1/16W JR1315 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR1316 NRSA63J-104X MG RESISTOR 100k 1/16W JR1319 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1322 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1401 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1402 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1403 NRSA63J-0R0X MG RESISTOR 0 1/16W JR1404 NRSA63J-0R0X MG RESISTOR 0 1/16W JR6106 NRSA63J-152X MG RESISTOR 1.5k 1/16W JR6107 NRSA63J-152X MG RESISTOR 1.5k 1/16W JR6114 NRSA63J-104X MG RESISTOR 100k 1/16W JR6115 NRSA63J-104X MG RESISTOR 100k 1/16W JR6117 NRSA63J-104X MG RESISTOR 100k 1/16W JR6118 NRSA63J-223X MG RESISTOR 22k 1/16W JR6119 NRSA63J-123X MG RESISTOR 12k 1/16W JR6120 NRSA63J-272X MG RESISTOR 2.7k 1/16W JR6123 NRSA63J-0R0X MG RESISTOR 0 1/16W JR6124 NRSA63J-223X MG RESISTOR 22k 1/16W JR6502 NRSA63J-563X MG RESISTOR 56k 1/16W JR6503 NRSA63J-104X MG RESISTOR 100k 1/16W JR6504 NRSA63J-563X MG RESISTOR 56k 1/16W JR6505 NRSA63J-183X MG RESISTOR 18k 1/16W JR6506 NRSA63J-0R0X MG RESISTOR 0 1/16W JR6508 NRSA63J-0R0X MG RESISTOR 0 1/16W JR6510 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR6511 NRSA63J-104X MG RESISTOR 100k 1/16W JR6513 NRSA63J-473X MG RESISTOR 47k 1/16W JR6515 NRSA63J-220X MG RESISTOR 22 1/16W JR6516 NRSA63J-102X MG RESISTOR 1k 1/16W JR6517 NRSA63J-102X MG RESISTOR 1k 1/16W JR6518 NRSA63J-220X MG RESISTOR 22 1/16W JR6661 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR6662 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR6665 NRSA63J-101X MG RESISTOR 100 1/16W JR6666 NRSA63J-101X MG RESISTOR 100 1/16W JR6669 NRSA63J-105X MG RESISTOR 1M 1/16W JR6671 NRSA63J-0R0X MG RESISTOR 0 1/16W JR6771 NRSA63J-683X MG RESISTOR 68k 1/16W JR6772 NRSA63J-683X MG RESISTOR 68k 1/16W JR6773 NRSA63J-473X MG RESISTOR 47k 1/16W JR6774 NRSA63J-473X MG RESISTOR 47k 1/16W JR6775 NRSA63J-682X MG RESISTOR 6.8k 1/16W JR6776 NRSA63J-682X MG RESISTOR 6.8k 1/16W JR6777 NRSA63J-272X MG RESISTOR 2.7k 1/16W JR6780 NRSA63J-103X MG RESISTOR 10k 1/16W JR6781 NRSA63J-0R0X MG RESISTOR 0 1/16W JR6782 NRSA63J-0R0X MG RESISTOR 0 1/16W JR7002 NRSA63J-823X MG RESISTOR 82k 1/16W JR7003 NRSA63J-104X MG RESISTOR 100k 1/16W JR7004 NRSA63J-104X MG RESISTOR 100k 1/16W JR7005 NRSA63J-224X MG RESISTOR 220k 1/16W JR7006 NRSA63J-750X MG RESISTOR 75 1/16W JR7007 NRSA63J-750X MG RESISTOR 75 1/16W JR7008 NRSA63J-750X MG RESISTOR 75 1/16W JR7009 NRSA63J-750X MG RESISTOR 75 1/16W JR7010 NRSA63J-183X MG RESISTOR 18k 1/16W JR7011 NRSA63J-183X MG RESISTOR 18k 1/16W JR7014 NRSA63D-102X MG RESISTOR 1k 1/16W DR7015 NRSA63D-102X MG RESISTOR 1k 1/16W DR7017 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR7018 NRSA63J-103X MG RESISTOR 10k 1/16W JR7020 NRSA63J-102X MG RESISTOR 1k 1/16W JR7022 NRSA63J-102X MG RESISTOR 1k 1/16W JR7023 NRSA63J-102X MG RESISTOR 1k 1/16W JR7027 NRSA63J-0R0X MG RESISTOR 0 1/16W JR7028 NRSA63J-0R0X MG RESISTOR 0 1/16W JR7029 NRSA63J-101X MG RESISTOR 100 1/16W JR7030 NRSA63J-101X MG RESISTOR 100 1/16W JR7031 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR7032 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR7033 NRSA63J-101X MG RESISTOR 100 1/16W JR7034 NRSA63J-101X MG RESISTOR 100 1/16W JR7039 NRSA63J-102X MG RESISTOR 1k 1/16W JR7043 NRSA63J-154X MG RESISTOR 150k 1/16W JR7044 NRSA63J-103X MG RESISTOR 10k 1/16W JR7045 NRSA63J-102X MG RESISTOR 1k 1/16W JR7049 NRSA63J-103X MG RESISTOR 10k 1/16W JR7050 NRSA63J-473X MG RESISTOR 47k 1/16W JR7052 NRSA63J-102X MG RESISTOR 1k 1/16W JR7053 NRSA63J-102X MG RESISTOR 1k 1/16W JR7061 NRSA63J-103X MG RESISTOR 10k 1/16W JR7062 NRSA63J-473X MG RESISTOR 47k 1/16W JR7065 NRSA63J-331X MG RESISTOR 330 1/16W JR7066 NRSA63J-102X MG RESISTOR 1k 1/16W JR7077 NRSA63J-0R0X MG RESISTOR 0 1/16W J

Ref No. Part No. Part Name Description Local

R7079 NRSA63J-0R0X MG RESISTOR 0 1/16W JR7080 NRSA63J-103X MG RESISTOR 10k 1/16W JR7082 NRSA63J-103X MG RESISTOR 10k 1/16W JR7083 NRSA63J-103X MG RESISTOR 10k 1/16W JR7084 NRSA63J-103X MG RESISTOR 10k 1/16W JR7085 NRSA63J-101X MG RESISTOR 100 1/16W JR7086 NRSA63J-101X MG RESISTOR 100 1/16W JR7087 NRSA63J-102X MG RESISTOR 1k 1/16W JR7088 NRSA63J-100X MG RESISTOR 10 1/16W JR7089 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR7090 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR7091 NRSA63D-153X MG RESISTOR 15k 1/16W DR7093 NRSA63D-683X MG RESISTOR 68k 1/16W DR7094 NRSA63D-393X MG RESISTOR 39k 1/16W DR7096 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR7097 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR7098 NRSA63J-101X MG RESISTOR 100 1/16W JR7099 NRSA63J-102X MG RESISTOR 1k 1/16W JR7100 NRSA63J-101X MG RESISTOR 100 1/16W JR7101 NRSA63J-101X MG RESISTOR 100 1/16W JR7102 NRSA63J-103X MG RESISTOR 10k 1/16W JR7103 NRSA63J-101X MG RESISTOR 100 1/16W JR7104 NRSA63J-101X MG RESISTOR 100 1/16W JR7105 NRSA63J-101X MG RESISTOR 100 1/16W JR7106 NRSA63J-101X MG RESISTOR 100 1/16W JR7107 NRSA63J-101X MG RESISTOR 100 1/16W JR7108 NRSA63J-101X MG RESISTOR 100 1/16W JR7109 NRSA63J-101X MG RESISTOR 100 1/16W JR7110 NRSA63J-101X MG RESISTOR 100 1/16W JR7111 NRSA63J-101X MG RESISTOR 100 1/16W JR7112 NRSA63J-101X MG RESISTOR 100 1/16W JR7113 NRSA63J-101X MG RESISTOR 100 1/16W JR7114 NRSA63J-101X MG RESISTOR 100 1/16W JR7115 NRSA63J-101X MG RESISTOR 100 1/16W JR7122 NRSA63J-101X MG RESISTOR 100 1/16W JR7123 NRSA63J-103X MG RESISTOR 10k 1/16W JR7125 NRSA63J-103X MG RESISTOR 10k 1/16W JR7126 NRSA63J-103X MG RESISTOR 10k 1/16W JR7127 NRSA63J-101X MG RESISTOR 100 1/16W JR7128 NRSA63J-102X MG RESISTOR 1k 1/16W JR7131 NRSA63J-101X MG RESISTOR 100 1/16W JR7132 NRSA63J-101X MG RESISTOR 100 1/16W JR7134 NRSA63J-101X MG RESISTOR 100 1/16W JR7135 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR7136 NRSA63J-102X MG RESISTOR 1k 1/16W JR7139 NRSA63J-103X MG RESISTOR 10k 1/16W JR7140 NRSA63J-473X MG RESISTOR 47k 1/16W JR7142 NRSA63J-103X MG RESISTOR 10k 1/16W JR7143 NRSA63J-473X MG RESISTOR 47k 1/16W JR7154 NRSA63J-101X MG RESISTOR 100 1/16W JR7155 NRSA63J-101X MG RESISTOR 100 1/16W JR7156 NRSA63J-0R0X MG RESISTOR 0 1/16W JR7157 NRSA63J-102X MG RESISTOR 1k 1/16W JR7158 NRSA63J-101X MG RESISTOR 100 1/16W JR7159 NRSA63J-101X MG RESISTOR 100 1/16W JR7160 NRSA63J-101X MG RESISTOR 100 1/16W JR7165 NRSA63J-101X MG RESISTOR 100 1/16W JR7167 NRSA63J-101X MG RESISTOR 100 1/16W JR7168 NRSA63J-103X MG RESISTOR 10k 1/16W JR7169 NRSA63J-103X MG RESISTOR 10k 1/16W JR7170 NRSA63J-103X MG RESISTOR 10k 1/16W JR7172 NRSA63J-332X MG RESISTOR 3.3k 1/16W JR8001 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8004 NRSA63J-103X MG RESISTOR 10k 1/16W JR8007 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR8011 NRSA63J-102X MG RESISTOR 1k 1/16W JR8015 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8017 NRSA63J-104X MG RESISTOR 100k 1/16W JR8018 NRSA63J-104X MG RESISTOR 100k 1/16W JR8019 NRSA63J-104X MG RESISTOR 100k 1/16W JR8101 NRSA63J-103X MG RESISTOR 10k 1/16W JR8102 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8107 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR8111 NRSA63J-102X MG RESISTOR 1k 1/16W JR8115 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8201 NRSA63J-103X MG RESISTOR 10k 1/16W JR8202 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8205 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR8211 NRSA63J-102X MG RESISTOR 1k 1/16W JR8215 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8501 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR8502 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR8504 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8505 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8507 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8508 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8510 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8511 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8512 NRSA63D-392X MG RESISTOR 3.9k 1/16W DR8514 NRSA63J-101X MG RESISTOR 100 1/16W J

Ref No. Part No. Part Name Description Local

3-10(No.YA604)

HP/USB P.W. BOARD ASS'Y (SFT-7303A-BK)

R8515 NRSA63J-0R0X MG RESISTOR 0 1/16W JR8516 NRSA63J-0R0X MG RESISTOR 0 1/16W JR9151 NRSA63D-683X MG RESISTOR 68k 1/16W DR9152 NRSA63D-123X MG RESISTOR 12k 1/16W DR9153 NRSA63D-103X MG RESISTOR 10k 1/16W DR9201 NRSA02J-680X MG RESISTOR 68 1/10W JR9202 NRSA63J-562X MG RESISTOR 5.6k 1/16W JR9203 NRSA63D-683X MG RESISTOR 68k 1/16W DR9204 NRSA63J-154X MG RESISTOR 150k 1/16W JR9205 NRSA63D-512X MG RESISTOR 5.1k 1/16W DR9206 NRSA63J-682X MG RESISTOR 6.8k 1/16W JR9207 NRSA63J-182X MG RESISTOR 1.8k 1/16W JR9208 NRSA63J-183X MG RESISTOR 18k 1/16W JR9209 NRSA63J-223X MG RESISTOR 22k 1/16W JR9221 NRSA63J-0R0X MG RESISTOR 0 1/16W JR9222 NRSA63J-104X MG RESISTOR 100k 1/16W JR9251 NRSA63D-152X MG RESISTOR 1.5k 1/16W DR9252 NRSA63J-103X MG RESISTOR 10k 1/16W JR9253 NRSA63D-222X MG RESISTOR 2.2k 1/16W DR9321 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR9351 NRSA02J-0R0X MG RESISTOR 0 1/10W JR9352 NRSA63J-103X MG RESISTOR 10k 1/16W JR9353 NRSA63D-682X MG RESISTOR 6.8k 1/16W DR9354 NRSA63J-823X MG RESISTOR 82k 1/16W JR9355 NRSA63D-512X MG RESISTOR 5.1k 1/16W DR9356 NRSA63J-471X MG RESISTOR 470 1/16W JR9357 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR9358 NRSA63J-183X MG RESISTOR 18k 1/16W JR9359 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR9360 NRSA63J-104X MG RESISTOR 100k 1/16W JR9601 NRSA02J-680X MG RESISTOR 68 1/10W JR9602 NRSA63J-103X MG RESISTOR 10k 1/16W JR9603 NRSA63D-333X MG RESISTOR 33k 1/16W DR9604 NRSA63J-224X MG RESISTOR 220k 1/16W JR9605 NRSA63D-512X MG RESISTOR 5.1k 1/16W DR9606 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR9607 NRSA63J-182X MG RESISTOR 1.8k 1/16W JR9608 NRSA63J-183X MG RESISTOR 18k 1/16W JR9609 NRSA63J-472X MG RESISTOR 4.7k 1/16W JR9610 NRSA63J-104X MG