G4111G4110G4100 G4101

U S E R G U I D E

®

GatewayE X T E N S I O N K I T S

®

C3C2

Parts l is t G4100/G4101A Upper Extension Housing (2)B Lower Extension Housing (2)C1 Extension Tube 7 7/8” (2) C2 Extension Tube 10 1/2” (2)D Extension Bar (2)

Parts l is t G4110/G4111C3 Extension Tube 4 3/4” (2)D Extension

C1

D

A

B

D

1 G4100/G4101 (Only)

Housings, bars and square extension tubes (5 1/8”) from gate may be needed. Depending on how many extensions are being added, insert the appropriate square extension tubes (c) into gate ends. Connect the bar (d) to one upper extension housing (a) and one lower extension housing (b).

Push assembly over extension tubes. There should be no metal showing from extension tubes. It may be necessary to apply pressure to tubes to ensure they are fully inserted into gate ends. Slide spindles into extension tubes.

2 G4110/G4111 (with orwithout G4100/G4101)

Insert 43/4” square extension tubes (c) into gate ends. Connect the extension (d) to gate. There should be no metal showing. It may be necessary to apply pressure. Slide spindles into extension. NOTE: If using additional extensions, 12.5” extension needs to be installed to gate first.

See applicable Gateway® series user guide to complete installation.

Insta l lat ion

1

2

(d)

(c)(a)

(b) (c)

(c)(c)

(c)(c)

(d)

Extension Placement GuideNote: Each G4100/G4101 kit contains two extensions • Each G4110/G4111 kit contains one extension

Width Opening Extensions What You Need Placement29”– 31 ½” Basic Gate No extensions31 ½” – 34 ½” Included with Gate Gate + 1 extension 34 ½” – 37” Gate + 2 extensions 37” – 40” Gate + 3 extensions 40” – 42 ½” Gate + 4 extensions 42 ½” – 45”

1-G4100/G4101

2-G4100/G4101 Gate + 5 extensions 45” – 47 ½” Gate + 6 extensions 47 ½”-49 ½” 1-G4110/G4111 Gate + 3 extensions

49 ½”-52” 1-1-G4110/G41 Gate + 4 extensions + 1-G4100/G4101

52”-55” Gate + 5 extensions

55”-57” 2-G4110/G4111 Gate + 2 extensions 57”-60” Gate + 3 extensions

60”-62” Gate + 4 extensions 62”-65” 2-2-G4110/G41 Gate + 5 extensions

+ 1-G4100/G4101 65”-68” Gate + 6 extensions 68”-70” 2-2-G4110/G41 Gate + 7 extensions

+ 2-G4100/G4101 70”-73 ½” Gate + 8 extensions

-1 on one end-1 on each end-2 on one end; 1 on other end-2 on each end-3 on one end; 2 on other end-3 on each end-G4110/4111 on either end; 1 extension on each end-1-G4110/4111 + 2 extensions on one end; 1 extension on other end-1 G4110/4111 + 2 extensions on one end; 2 extensions on other end-1 G4110/4111 on each end-1 G4110/4111 on each end; 1 extension on one end-1 G4110/4111 + 1 extension on each end-1-G4110/4111 + 1 extension on each end; 1 extension on one end-1 G4110/4111 + 2 extensions on each end-1-G4110/4111 + 2 extensions on each end; 1 extension on one end-1-G4110/4111 + 3 extensions on each end

Gateway® SeriesExtension Kit model G5.5c(contains two extensions)

FOLLOW THESE INSTRUCTIONSCAREFULLY AND KEEP THEM FORFUTURE REFERENCE

Extensions must be added as shown.

Extension Placement Guide for Center Gateway (Model G15):

291/4”-347/8” Gate + 1 extension - may be placed on either end341/2”-371/2” Gate + 2 extensions - one on each end

371/4”-401/4” Gate + 3 extensions - 2 on one end, 1 on other end397/8”-423/4” Gate + 4 extensions - 3 on one end, 1 on other end

425/8”-455/8” Gate + 5 extensions - 3 on one end, 2 on other end451/2”-481/8” Gate + 6 extensions - 3 on each end

Each end may have no more than 3 extensions.

Extension Placement Guide for Wood Center Gateway (Model G35):

28”-331/2” Gate + 1 extension - may be placed on either end331/8”-36” Gate + 2 extensions - one on each end

353/4”-383/4” Gate + 3 extensions - 2 on one end, 1 on other end385/8”-411/2” Gate + 4 extensions - 3 on one end, 1 on other end

411/4”-44” Gate + 5 extensions - 3 on one end, 2 on other end433/4”-47” Gate + 6 extensions - 3 on each end

Each end may have no more than 3 extensions.

Extension Placement Guide for Gateway (Model G11):

30”-36” Gate + 1 extension

35”-38” Gate + 2 extensions371/2”-411/2” Gate + 3 extensions

No more than 3 extensions per gate.

Important Information

1. Housings, bars and square extension tubes(51/8”) from Basic Center Gateway Set may beneeded.Depending on how many extensions are beingadded, insert appropriate square extensiontubes (s or t) into gate ends. Connect the bar (k)to one upper extension housing (h) and onelower extension housing (i).

ENG

InstallationPush assembly over extension tubes. Thereshould be no metal showing from extensiontubes. It may be necessary to apply pressure totubes to ensure they are fully inserted into gateends. Slide spindles into extension tubes.

See applicable Gateway® series user guide tocomplete installation.

Extension Placement Guides

Included with gate

One optional extension kit

Two optional extension kits

{

{

{

Included with gate

One optional extension kit

Two optional extension kits

{

{

{

Included with gate

One optional extension kit {

{ {Must be placed on opposite side of handle end

Parts Check List

(h) - 2 (i) - 2 (s) - 2 (77/8”) (t) - 2 (101/2”) (k) - 2

1.

(i)

(h) (s) or (t)

(s) or (t)

(k)

On our website you can discover more about Pet Supplies.