Kyocera Mita - Trouble Error Codes List

2

FS1035MFP - English

Code Description Causes

0030 FAX PWB system error Processing with the fax software was disabled due to a hardware problem.

Defective FAX PWB.

0070 FAX PWB incompatible detection Error Abnormal detection of FAX PWB incompatibility In the initial communication with the FAX PWB, any normal communication command is not transmitted.

Defective fax software. Defective FAX PWB.

0100 Backup memory device error Defective flash memory. Defective control PWB.

0120 MAC address data error Defective flash memory.

0130 Backup memory read/write error Defective flash memory. Defective control PWB.

0140 Backup memory data error Defective flash memory. Defective control PWB.

0150 Control PWB EEPROM error Detecting control PWB EEPROM (U17) communication error.

Improper installation control PWB EEPROM (U17). Defective control PWB. Data damage of control PWB EEPROM (U17).

0170 Billing counting error Defective control PWB. Data damage of control PWB EEPROM (U17).

0180 Machine number mismatch Machine number of main and engine does not match.

Data damage of control PWB EEPROM (U17).

0420 Paper feeder communication error Communication error between control PWB and optional paper feeder.

Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion.

0830 FAX PWB flash program area checksum error A checksum error occurred with the program of the FAX PWB.

Defective fax software. Defective FAX PWB.

0840 Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.

Defective control PWB. The battery is disconnected from the control PWB.

0870 FAX PWB to control PWB high capacity data transfer problem High-capacity data transfer between the FAX PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times.

Improper installation FAX PWB. Defective FAX PWB or control PWB.

0920 Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX PWB.

Defective FAX PWB. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.

2000 Main motor error The main motor ready input is not

Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective

3

Code Description Causes given for 2 s during the main motor is ON.

drive transmission system of the main motor. Defective main motor. Defective control PWB.

2610 PF paper feed motor error (paper feeder) The PF paper feed motor of cassette 2 ready input is not given for 2 s during the PF paper feed motor is ON.

Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective control PWB.

2620 PF paper feed motor error (Paper feeder) The PF paper feed motor of cassette 3 ready input is not given for 2 s during the PF paper feed motor is ON.

Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor.

3100 ISU home position error Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Defective home position sensor. Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Defective ISU motor.

3200 Exposure lamp error The exposure lamp is not turned on.

Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and inverter PWB (YC101), or improper connector insertion. Defective harness between inverter PWB (YC102) and exposure lamp, or improper connector insertion. Defective exposure lamp. Defective inverter PWB. Defective control PWB.

3300 AGC error After AGC, correct input is not obtained at CCD.

Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp. Defective CCD PWB. Defective control PWB.

3500 CPU - ASIC (CCD PWB) communication error An error code is detected.

Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB.

4000 Polygon motor (laser scanner unit) error The polygon motor ready input is not given for 6 s during the polygon motor is ON.

Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.

4200 BD error (laser scanner unit) error BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.

6000 Broken fuser heater lamp wire The fuser temperature does not rise after the fuser heater lamp has been turned on.

Poor contact in the fuser thermistor connector terminals. Poor contact in the fuser heater lamp connector terminals. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater lamp installed incorrectly. Broken fuser heater lamp wire.

6020 Abnormally high fuser thermistor temperature Fuser thermistor detects abnormally temperature.

Shorted fuser thermistor. Defective control PWB.

6030 Broken fuser thermistor wire Input from fuser thermistor is 0 (A/D value).

Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater lamp installed incorrectly. Broken fuser heater lamp wire.

4


6400 Zero cross signal error The zero cross signal does not reach the control PWB for specified time.

Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (YC201). Defective power source PWB. Defective control PWB.

7990 Waste toner full The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.

Waste toner reservoir (drum unit) is full. Defective waste toner sensor. Defective control PWB.

F000 Control PWB - Operation panel PWB communication error

Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. Defective operation panel PWB. Defective control PWB.

F020 Control PWB RAM checksum error Defective main memory (RAM) on the control PWB. Defective expanded memory (DIMM).

F040 Control PWB engine communication error A communication error is detected.

Defective control PWB.

F041 Control PWB - scanner PWB communication error A communication error is detected.

Defective control PWB or scanner PWB.

F050 Control PWB engine checksum error

Some error may have occurred when downloading the firmware of the control PWB. Defective control PWB.

F186 Control PWB video data control error


FS1035MFP - Portugus

Cdigo Descrio Causas

0030 FAX PWB erro do sistema de processamento com o software de fax foi desativada devido a um problema de hardware.

PWB FAX defeito.

0070 FAX PWB incompatvel Erro de deteco de deteco anormal de FAX PWB incompatibilidade Na comunicao inicial com o PWB FAX, qualquer comando normal de comunicao no transmitida.

Software fax com defeito. PWB FAX defeito.

0100 Erro do dispositivo de memria de backup

Memria flash danificada. PWB de controle com defeito.

0120 MAC erro de dados de endereo Memria flash danificada.

0130 Memria de backup de leitura / erro de gravao


0140 Erro de dados na memria de backup


5


0150 Controle PWB EEPROM erro controle Detectando EEPROM PWB (U17) erro de comunicao.

Imprpria EEPROM PWB de controle de instalao (U17). PWB de controle com defeito. Danificar os dados da EEPROM controle PWB (U17).

0170 Erro de contagem de facturao PWB de controle com defeito. Danificar os dados da EEPROM controle PWB (U17).

0180 Nmero da mquina incompatibilidade nmero Mquina de principal e do motor no corresponde.

Danificar os dados da EEPROM controle PWB (U17).

0420 Alimentador de papel erro de comunicao Erro de comunicao entre o controle PWB e alimentador de papel opcional.

Alimentador de papel instalao inadequada. Arns defeituoso entre PWB de controle (YC30) e conector de interface de alimentao de papel, ou insero conector imprprio. PWB de controle com defeito. Arns defeituoso entre a principal PWB PF (YC5) e conector de interface de alimentao de papel, ou insero conector imprprio.

0830 FAX PWB erro de checksum rea programa de flash Ocorreu um erro de soma de verificao com o programa do PWB FAX.

Software fax com defeito. PWB FAX defeito.

0840 Falhas de RTC O tempo julgado para voltar com base na comparao do tempo RTC eo tempo atual ou cinco anos ou mais se passaram.

PWB de controle com defeito. A bateria desligado do PWB de controle.

0870 FAX PWB para controlar PWB de alta capacidade problema de transferncia de dados de transferncia de dados de alta capacidade entre o PWB FAX eo PWB de controle da mquina no foi realizada normalmente, mesmo que a transferncia de dados foi repetida nos horrios especificados.

Imprpria PWB FAX instalao. PWB FAX com defeito ou controle PWB.

0920 Erro do sistema de arquivos Fax Os dados de backup no mantida por anomalia do sistema de arquivos de memria flash do PWB FAX.

PWB FAX defeito. Defeituoso sistema de transmisso de acionamento do motor de alimentao de papel PF. Defeito motor principal PF. PWB de controle com defeito.

2.000 Erro do motor principal A entrada principal pronto motor no dada por 2 s durante o motor principal ON.

Arns com defeito entre o motor principal (CN1) e PWB de controle (YC17), ou insero conector imprprio. Defeituoso sistema de transmisso da unidade do motor principal. Motor principal defeito.PWB de controle com defeito.

2.610 PF erro do motor de alimentao de papel (alimentador de papel) O motor de alimentao de papel PF de cassete 2 de entrada pronto no dado por 2 s durante o motor de alimentao de papel PF ON.

Arns defeituoso entre PF motor de alimentao de papel e principal PWB PF (YC4), ou insero conector imprprio. PWB de controle com defeito.

2.620 PF erro do motor de alimentao de papel (alimentador de papel) O motor de alimentao de papel PF de cassete 3 entrada pronto no dado por 2 s durante o motor de

Arns defeituoso entre PF motor de alimentao de papel e principal PWB PF (YC4), ou insero conector imprprio.Defeituoso sistema de transmisso de acionamento do motor de alimentao de papel PF. Defeito motor principal PF.

6

Cdigo Descrio Causas alimentao de papel PF ON.

3100 ISU erro posio inicial FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). FFC defeituosa entre PWB de controle (YC6) e PWB scanner (YC103), ou insero FFC imprpria. Sensor de posio inicial com defeito. Arns com defeito entre o motor ISU e PWB scanner (YC104), ou insero conector imprprio. Motora ISU defeito.

3200 Erro lmpada de exposio A lmpada de exposio no est ligada.

FFC defeituosa entre PWB scanner (YC103) e PWB de controle (YC6), ou insero FFC imprpria. FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). Arns defeituoso entre CCD PWB (Yc3) e inversor PWB (YC101), ou insero conector imprprio. Arns defeituoso entre inversor PWB (YC102) e lmpada de exposio, ou insero conector imprprio. Lmpada de exposio com defeito. Defeito inversor PWB. PWB de controle com defeito.

3300 Erro AGC AGC Depois, a entrada correta no obtida em CCD.

FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). Lmpada de exposio com defeito. PWB CCD defeituoso. PWB de controle com defeito.

3500 CPU - ASIC (CCD PWB) erro de comunicao Um cdigo de erro detectado.

FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). PWB CCD defeituoso. PWB de controle com defeito.

4000 Motor de Polygon (unidade de digitalizao a laser) Erro O motor polgono de entrada pronto no dado por 6 s durante o motor polgono ON.

Arns com defeito entre o motor polgono e PWB de controle (YC10), ou insero conector imprprio. Unidade de scanner a laser com defeito. PWB de controle com defeito.

4200 Erro BD (unidade de digitalizao a laser) erro

Sensor de BD no detecta feixe de laser devido condensao no espelho polgono. Unidade de scanner a laser com defeito.PWB de controle com defeito.

6000 Quebrado aquecedor de fuso de arame lmpada A temperatura do fusor no aumenta aps a lmpada de aquecimento do fusor foi ligado.

Mau contato nos terminais do conector do fusor termistor. Mau contato no aquecedor do fusor terminais do conector da lmpada. Fuser termistor instalado incorretamente. Fuser corte trmico disparado. Lmpada de aquecimento do fusor instalado incorretamente. Quebrado fio lmpada de aquecimento do fusor.

6020 Anormalmente elevada temperatura do fusor termistor do fusor termistor detecta temperatura anormal.

Termistor do fusor em curto. PWB de controle com defeito.

6030 Fio fusor termistor quebrado entrada do fusor termistor 0 (valor A / D).

Mau contato nos terminais do conector do fusor termistor. Quebrado fio fusor termistor. Fuser termistor instalado incorretamente. Fuser corte trmico disparado. Lmpada de aquecimento do fusor instalado incorretamente. Quebrado fio lmpada de aquecimento do fusor.

6400 Zero erro de sinal cruz O sinal de cruz zero no atingir o PWB de controle de tempo especificado.

Arns defeituoso entre PWB de alta tenso (YC202) e PWB de controle (YC23), ou insero conector imprprio. Conexo defeituosa entre PWB fonte de alimentao (YC103) e PWB de alta tenso (YC201). Defeituoso PWB fonte de energia. PWB de controle com defeito.

7990 Resduos de toner cheia O sensor de resduos de toner detectou que o reservatrio de

Reservatrio de resduos de toner (tambor) est cheio. Sensor de resduos de toner com defeito. PWB de controle com defeito.

7

Cdigo Descrio Causas resduos de toner (tambor) est cheio.

F000 PWB de controle - painel de erro de comunicao PWB Operao

Arns defeituoso entre PWB painel de operao (YC1) e PWB de controle (YC7), ou insero conector imprprio. Defeituoso PWB painel de operao. PWB de controle com defeito.

F020 Erro de checksum Controle PWB RAM

De memria com defeito principal (RAM) no PWB de controle. Memria expandida com defeito (DIMM).

F040 Controle PWB erro de comunicao motor de um erro de comunicao seja detectado.

PWB de controle com defeito.

F041 Controle PWB - erro de comunicao PWB scanner de um erro de comunicao seja detectado.

PWB de controle com defeito ou scanner PWB.

F050 Controle PWB erro de soma de verificao do motor

Alguns erros podem ter ocorrido quando o download do firmware do PWB de controle. PWB de controle com defeito.

F186 Controle PWB erro de controle de dados de vdeo


KM2020 - English


C0100 Backup memory read/write problem (main PCB) Read and write data does not match.

Defective backup RAM or main PCB.

C0110 Backup memory data problem (main PCB) Data in the specified area of the backup memory does not match the specified values.

Problem with the backup memory data. Defective backup RAM.

C0150 Backup memory read/write problem (engine PCB) Read and write data does not match.

Defective backup RAM or engine PCB.

C0160 Backup memory data problem (engine PCB) Data in the specified area of the backup memory does not match the specified values.

Problem with the backup memory data. Defective backup RAM.

C0170 Accounting count problem When the power is turned on, the total count and the scan count are abnormal both on the main PCB and the engine PCB.

Defective main PCB or engine PCB.

C0180 Machine number mismatch When the power is turned on, the machine number does not match between the main PCB and the engine PCB.

Correct EEPROM is not installed. Data damage of EEPROM.

C0210 Communication problem between the main PCB and engine board PCB When the power is turned on, the machine does not detect the low level of SBSY and the high

Poor contact in the connector terminals. Defective main PCB or engine PCB.

8

Code Description Causes level of SDIR for three seconds.

C0410 Optional DP communication problem Communication fails five times successively.

DP installed incorrectly. Defective main PCB or DP driver PCB.

C0420 Optional first paper feeder communication problem Communication fails five times successively.

Paper feeder installed incorrectly. Defective main PCB or drawer main PCB.

C0500 Optional second paper feeder communication problem Communication fails five times successively.


C0510 Optional third paper feeder communication problem Communication fails five times successively.


C0610 Bitmap (DIMM) problem There is a problem with the data or address bus of the bitmap DRAM.

Defective main PCB. DIMM installed incorrectly. Defective DIMM.

C0620 Memory input interface problem Reading-in of an image does not complete within 10 s of the start of image transmission.

Defective main PCB.

C0630 DMA problem DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time.

Defective main PCB.

C0800 Image processing problem JAM05 is detected twice.

Defective engine PCB.

C2000 Drive motor problem LOCK ALM signal remains high for 1 s, 1 s after the drive motor has turned on.

Poor contact in the main motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.

C3100 Scanner carriage problem The home position is not correct when the power is turned on or copying the document placed on the contact glass.

Poor contact of the connector terminals. Defective scanner home position switch. Defective engine PCB. Defective scanner motor.

C3200 Exposure lamp problem In indicator check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more.

Poor contact of the connector terminals. Defective exposure lamp or inverter board. Defective engine PCB. Incorrect shading position.

C3300 Optical system (AGC) problem After AGC, correct input is not obtained at CCD.

Insufficient exposure lamp luminosity. Defective engine PCB. Incorrect shading position.

C4000 Polygon motor synchronization problem The polygon motor does not reach the stable speed within 15 s of the START signal turning on.

Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PCB.

C4010 Polygon motor steady-state problem The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized.


C4200 BD steady-state problem The MIC detects a BD error for 600ms after the polygon motor rotation has been stabilized.

Defective laser diode. Defective polygon motor. Defective main PCB. Defective engine PCB.

C6000 Broken fixing heater wire Poor contact in the thermistor connector

9

Code Description Causes In fixing warm-up, the time to reach 50C/122 F exceeds 13.5 s, the time to reach 100C/212 F exceeds 10 s, the time to reach the primary stabilization exceeds 10 s or the time to reach the secondary stabilization exceeds 24 s.

terminals. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.

C6020 Abnormally high fixing unit thermistor temperature The fixing temperature exceeds 230C/446 F for 40 ms.

Shorted thermistor. Broken heater control circuit on the power supply PCB.

C6050 Abnormally low fixing unit thermistor temperature The fixing temperature remains below 90C/194F for 1 s.

Poor contact in the thermistor connector terminals. Broken fixing thermistor wire. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.

C6400 Zero-crossing signal problem The engine PCB does not detect the zero-crossing signal for the time specified below. At power-on: 3 s Others: 5 s

Poor contact in the connector terminals. Defective power supply PCB. Defective engine PCB.

C7800 Broken external temperature thermistor The input voltage is 0.5 V or less.

Poor contact in the humidity sensor connector terminals. Defective humidity sensor.

C7810 Short-circuited external temperature thermistor The input voltage is 4.5 V or more.

Defective humidity sensor. Poor contact in the humidity sensor connector terminals. Defective humidity sensor.

KM2020 - Portugus


C0100 Memria de backup de leitura / gravao problema (PCB principal) Ler e escrever dados no correspondem.

RAM de backup com defeito ou PCB principal.

C0110 Problema de backup de dados de memria (PCB principal) Dados na rea especificada da memria de segurana no coincide com os valores especificados.

Problema com os dados da memria de backup. RAM de backup com defeito.

C0150 Memria de backup de leitura / gravao problema (PCB motor) Ler e escrever dados no correspondem.

RAM de backup com defeito ou PCB motor.

C0160 Problema de memria de backup de dados (PCB motor) Dados na rea especificada da memria de segurana no coincide com os valores especificados.

Problema com os dados da memria de backup. RAM de backup com defeito.

C0170 Contabilidade contagem problema Quando o aparelho ligado, a contagem total ea contagem de digitalizao so anormais, tanto no PCB principal eo PCB motor.

PCB principal defeituoso ou PCB motor.

C0180 Nmero da mquina incompatibilidade EEPROM correto no estiver instalado. Danificar

10

Cdigo Descrio Causas Quando o aparelho ligado, o nmero da mquina no corresponder entre o PCB principal eo PCB motor.

os dados da EEPROM.

C0210 Problema de comunicao entre a placa principal PCB e PCB motor Quando a alimentao ligada, a mquina no detecta o baixo nvel de SBSY e do elevado nvel de SDIR por trs segundos.

Mau contato nos terminais do conector. PCB principal defeituoso ou PCB motor.

C0410 Opcional problema de comunicao DP Comunicao falha cinco vezes sucessivamente.

DP instalado incorretamente. PCB principal defeituoso ou DP PCB motorista.

C0420 Opcional problema primeira comunicao alimentador de papel Comunicao falha cinco vezes sucessivamente.

Alimentador de papel instalado incorretamente. PCB principal defeituoso ou PCB principal gaveta.

C0500 Opcional segundo problema de comunicao alimentador de papel Comunicao falha cinco vezes sucessivamente.


C0510 Problema de comunicao opcional terceiro alimentador de papel Comunicao falha cinco vezes sucessivamente.


C0610 Bitmap (DIMM) problema H um problema com os dados ou endereo de nibus da DRAM bitmap.

PCB principal defeito. DIMM instalado incorretamente. DIMM com defeito.

C0620 Problema interface de entrada de Memria Reading-in de uma imagem no for concluda dentro de 10 s aps o incio da transmisso de imagem.

PCB principal defeito.

C0630 Problema DMA transmisso DMA de comprimido, descomprimido, rodado, realocados ou imagem estampada-out no concludo dentro do perodo de tempo especificado.

PCB principal defeito.

C0800 Problema de processamento de imagem JAM05 detectado duas vezes.

PCB defeituosa do motor.

C2000 Drive motor problem LOCK ALM signal remains high for 1 s, 1 s after the drive motor has turned on.

Poor contact in the main motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.

C3100 Scanner carriage problem The home position is not correct when the power is turned on or copying the document placed on the contact glass.

Poor contact of the connector terminals. Defective scanner home position switch. Defective engine PCB. Defective scanner motor.

C3200 Exposure lamp problem In indicator check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more.

Poor contact of the connector terminals. Defective exposure lamp or inverter board. Defective engine PCB. Incorrect shading position.

C3300 Optical system (AGC) problem After AGC, correct input is not obtained at CCD.

Insufficient exposure lamp luminosity. Defective engine PCB. Incorrect shading position.

C4000 Polygon motor synchronization problem The polygon motor does not reach the

Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective

11

Cdigo Descrio Causas stable speed within 15 s of the START signal turning on.

engine PCB.

C4010 Polygon motor steady-state problem The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized.


C4200 BD steady-state problem The MIC detects a BD error for 600ms after the polygon motor rotation has been stabilized.

Defective laser diode. Defective polygon motor. Defective main PCB. Defective engine PCB.

C6000 Broken fixing heater wire In fixing warm-up, the time to reach 50C/122 F exceeds 13.5 s, the time to reach 100C/212 F exceeds 10 s, the time to reach the primary stabilization exceeds 10 s or the time to reach the secondary stabilization exceeds 24 s.

Poor contact in the thermistor connector terminals. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.

C6020 Abnormally high fixing unit thermistor temperature The fixing temperature exceeds 230C/446 F for 40 ms.

Shorted thermistor. Broken heater control circuit on the power supply PCB.

C6050 Abnormally low fixing unit thermistor temperature The fixing temperature remains below 90C/194F for 1 s.

Poor contact in the thermistor connector terminals. Broken fixing thermistor wire. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.

C6400 Zero-crossing signal problem The engine PCB does not detect the zero-crossing signal for the time specified below. At power-on: 3 s Others: 5 s

Poor contact in the connector terminals. Defective power supply PCB. Defective engine PCB.

C7800 Broken external temperature thermistor The input voltage is 0.5 V or less.

Poor contact in the humidity sensor connector terminals. Defective humidity sensor.

C7810 Short-circuited external temperature thermistor The input voltage is 4.5 V or more.

Defective humidity sensor. Poor contact in the humidity sensor connector terminals. Defective humidity sensor.

KM2810 - English


0100 Backup memory device error Defective flash memory. Defective control PWB.

0120 MAC address data error Defective flash memory.

0130 Backup memory read/write error Defective flash memory. Defective control PWB.

0140 Backup memory data error Defective flash memory. Defective control PWB.

0150 Control PWB EEPROM error Detecting control PWB EEPROM (U17) communication error.

Improper installation control PWB EEPROM (U17). Defective control PWB. Data damage of control PWB EEPROM (U17).

12


0170 Billing counting error Defective control PWB. Data damage of control PWB EEPROM (U17).


Data damage of control PWB EEPROM (U17).

0420 Paper feeder communication error Communication error between control PWB and optional paper feeder.

Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF main-PWB.

2000 Main motor error The main motor ready input is not given for 2 s during the main motor is ON

Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective drive transmission system of the main motor. Defective main motor. Defective control PWB.

2610 PF paper feed motor error (Optional paper feeder 1) The PF paper feed motor of paper feeder 1 ready input is not given for 2 s during the PF paper feed motor is ON.

Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.

2620 PF paper feed motor error (Optional paper feeder 2) The PF paper feed motor of paper feeder 2 ready input is not given for 2 s during the PF paper feed motor is ON.

Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.

3100 ISU home position error Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Defective home position sensor. Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Defective ISU motor.

3200 Exposure lamp error The exposure lamp is not turned on.

Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and inverter PWB (YC101), or improper connector insertion. Defective harness between inverter PWB (YC102) and exposure lamp, or improper connector insertion. Defective exposure lamp. Defective inverter PWB. Defective control PWB.


Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp. Defective CCD PWB. Defective control PWB.

3500 CPU - ASIC (CCD PWB) communication error An error code is detected.

Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB.

4000 Polygon motor (laser scanner unit) error The polygon motor ready input is not given for 6 s during the polygon motor is ON.

Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.

4200 BD error (laser scanner unit) error BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.

13


6000 Broken fuser heater lamp wire The fuser temperature does not rise after the fuser heater lamp has been turned on.

Poor contact in the fuser thermistor connector terminals. Poor contact in the fuser heater lamp connector terminals. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater lamp installed incorrectly. Broken fuser heater lamp wire.

6020 Abnormally high fuser thermistor temperature Fuser thermistor detects abnormally temperature.

Shorted fuser thermistor. Defective control PWB.

6030 Broken fuser thermistor wire Input from fuser thermistor is 0 (A/D value).

Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater lamp installed incorrectly. Broken fuser heater lamp wire.

6400 Zero cross signal error The zero cross signal does not reach the control PWB for specified time.

Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (YC201). Defective power source PWB. Defective control PWB.

7990 Waste toner full The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.

Waste toner reservoir (drum unit) is full. Defective waste toner sensor. Defective control PWB.

F000 Control PWB - Operation panel PWB communication error

Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. Defective operation panel PWB. Defective control PWB.

F020 Control PWB RAM checksum error Defective main memory (RAM) on the control PWB. Defective expanded memory (DIMM).

F040 Control PWB engine communication error


F041 Control PWB - scanner PWB communication error A communication error is detected.

Defective control PWB or scanner PWB.

F050 Control PWB engine checksum error

Some error may have occurred when downloading the firmware of the control PWB. Defective control PWB.

F186 Control PWB video data control error


KM2810 - Portugus


0100 Erro do dispositivo de memria de backup


0120 MAC erro de dados de endereo Memria flash danificada.

0130 Memria de backup de leitura / erro de gravao


0140 Erro de dados na memria de backup


14


0150 Controle PWB EEPROM controle Deteco de erro EEPROM PWB (U17) erro de comunicao.

Imprpria EEPROM PWB de controle de instalao (U17). PWB de controle com defeito. Danificar os dados da EEPROM controle PWB (U17).

0170 Erro de contagem de facturao PWB de controle com defeito. Danificar os dados da EEPROM controle PWB (U17).

0180 Nmero da mquina nmero Mquina incompatibilidade de principal e do motor no corresponde.

Danificar os dados da EEPROM controle PWB (U17).

0420 Alimentador de papel de erro erro de comunicao A comunicao entre o controle PWB e alimentador de papel opcional.

Alimentador de papel instalao inadequada. Arns defeituoso entre PWB de controle (YC30) e conector de interface de alimentao de papel, ou insero conector imprprio. PWB de controle com defeito chicote defeituoso entre a principal PWB PF (YC5) e conector de interface de alimentao de papel, ou insero conector imprprio. Defeituoso PF main-PWB.

2.000 Erro do motor principal A entrada pronto motor principal no dado por 2 s durante o motor principal ON

Arns com defeito entre o motor principal (CN1) e PWB de controle (YC17), ou insero conector imprprio.Defeituoso sistema de transmisso da unidade do motor principal. Motor principal defeito. PWB de controle com defeito.

2.610 PF erro do motor de alimentao de papel (alimentador de papel opcional 1) O motor de alimentao de papel PF de alimentador de papel 1 entrada pronto no dado por 2 s durante o motor de alimentao de papel PF ON.

Arns defeituoso entre PF motor de alimentao de papel e principal PWB PF (YC4), ou insero conector imprprio. Defeituoso sistema de transmisso de acionamento do motor de alimentao de papel PF. Defeito motor principal PF. PWB de controle com defeito.

2.620 PF erro do motor de alimentao de papel (alimentador de papel opcional 2) O motor de alimentao de papel PF de alimentador de papel 2 de entrada pronto no dado por 2 s durante o motor de alimentao de papel PF ON.

Arns defeituoso entre PF motor de alimentao de papel e principal PWB PF (YC4), ou insero conector imprprio. Defeituoso sistema de transmisso de acionamento do motor de alimentao de papel PF. Defeito motor principal PF. PWB de controle com defeito.

3100 ISU erro posio inicial FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). FFC defeituosa entre PWB de controle (YC6) e PWB scanner (YC103), ou insero FFC imprpria. Sensor de posio inicial com defeito. Arns com defeito entre o motor ISU e PWB scanner (YC104), ou insero conector imprprio. Motora ISU defeito.

3200 Erro de lmpada de exposio A lmpada de exposio no est ligada.

FFC defeituosa entre PWB scanner (YC103) e PWB de controle (YC6), ou insero FFC imprpria. FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). Arns defeituoso entre CCD PWB (Yc3) e inversor PWB (YC101), ou insero conector imprprio. Arns defeituoso entre inversor PWB (YC102) e lmpada de exposio, ou insero conector imprprio. Lmpada de exposio com defeito. Defeito inversor PWB. PWB de controle com defeito.

3300 Aps erro AGC AGC, a entrada correta no obtida em CCD.

FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). Lmpada de exposio com defeito. PWB CCD defeituoso. PWB de controle com defeito.

3500 CPU - ASIC (CCD PWB) erro de comunicao Um cdigo de erro detectado.

FFC defeituosa entre CCD PWB (YC1) e controle PWB (YC8). PWB CCD defeituoso. PWB de controle com defeito.

15


4000 Motor de Polygon (unidade de digitalizao a laser) Erro O motor polgono de entrada pronto no dado por 6 s durante o motor polgono ON.

Arns com defeito entre o motor polgono e PWB de controle (YC10), ou insero conector imprprio. Unidade de scanner a laser com defeito. PWB de controle com defeito.

4200 Erro BD (unidade de digitalizao a laser) erro

Sensor de BD no detecta feixe de laser devido condensao no espelho polgono. Unidade de scanner a laser com defeito. PWB de controle com defeito.

6000 Quebrado aquecedor de fuso de arame lmpada A temperatura do fusor no aumenta aps a lmpada de aquecimento do fusor foi ligado.

Mau contato nos terminais do conector do fusor termistor. Mau contato no aquecedor do fusor terminais do conector da lmpada. Fuser termistor instalado incorretamente. Fuser corte trmico disparado. Lmpada de aquecimento do fusor instalado incorretamente. Quebrado fio lmpada de aquecimento do fusor.

6020 Anormalmente elevada temperatura do fusor termistor do fusor termistor detecta temperatura anormal.

Termistor do fusor em curto. PWB de controle com defeito.

6030 Entrada fio fusor termistor quebrada de fusor termistor 0 (valor A / D).

Mau contato nos terminais do conector do fusor termistor. Quebrado fio fusor termistor. Fuser termistor instalado incorretamente. Fuser corte trmico disparado. Lmpada de aquecimento do fusor instalado incorretamente.Quebrado fio lmpada de aquecimento do fusor.

6400 Zero erro de sinal O sinal de cruz cruz de zero no atingir o PWB de controle de tempo especificado.

Arns defeituoso entre PWB de alta tenso (YC202) e PWB de controle (YC23), ou insero conector imprprio.Conexo defeituosa entre PWB fonte de alimentao (YC103) e PWB de alta tenso (YC201). Defeituoso PWB fonte de energia. PWB de controle com defeito.

7990 Resduos de toner cheia O sensor de resduos de toner detectou que o reservatrio de resduos de toner (tambor) est cheio.

Reservatrio de resduos de toner (tambor) est cheio. Sensor de resduos de toner com defeito. PWB de controle com defeito.

F000 PWB de controle - painel de erro de comunicao PWB Operao

Arns defeituoso entre PWB painel de operao (YC1) e PWB de controle (YC7), ou insero conector imprprio.Defeituoso PWB painel de operao. PWB de controle com defeito.

F020 Erro de checksum Controle PWB RAM

De memria com defeito principal (RAM) no PWB de controle. Memria expandida com defeito (DIMM).

F040 Controle PWB erro de comunicao do motor


F041 Controle PWB - erro de comunicao PWB scanner de um erro de comunicao seja detectado.

PWB de controle com defeito ou scanner PWB.

F050 Controle PWB erro de soma de verificao do motor

Alguns erros podem ter ocorrido quando o download do firmware do PWB de controle. PWB de controle com defeito.

F186 Controle PWB erro de controle de dados de vdeo


16

TASKalfa 255 - English


0030 FAX control PWB system error Processing with the fax software was disabled due to a hardware problem.

Defective FAX control PWB.

0060 Engine PWB type error Defective engine sub PCB.

0070 FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.

Defective FAX software Defective FAX control PWB.

0100 Backup memory device error Defective flash memory.

0120 MAC address data error For data in which the MAC address is invalid.

Defective main PWB. Defective flash memory. Defective engine PWB.

0130 Backup memory read/write error (main PWB) Defective flash memory. Defective main PWB.

0140 Backup memory data error (main PWB) Defective flash memory. Defective main PWB.

0150 Backup memory read/write error (engine PWB) Detecting engine PWB EEPROM communication error.

Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM.

0160 Backup memory data error (engine PWB) Defective flash memory. Defective engine PWB.

0170 Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters.

Data damage of EEPROM. Defective PWB.


Data damage of EEPROM.

0320 I/O CPU communication error A communication error is detected 10 times in succession.

Defective PWB.

0630 DMA error DMA transmission of image data does not complete within the specified period of time.

Poor contact in the connector terminals. Defective main PWB.

0800 Image processing error JAM05 is detected twice.

Defective main PWB.

0830 FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.

Defective FAX software. Defective FAX control PWB.

0840 Faults of RTC The battery is

17

Code Description Causes The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.

disconnected from the main PWB. Defective main PWB.

0870 FAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times.

Improper installation FAX control PWB. Defective FAX control PWB or main PWB.

0920 Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.


1010 Lift motor error After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively.

Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB.

1020 PF lift motor error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively.

Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 1. Defective PF lift motor 1. Defective PF main PWB.

1030 PF lift motor error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively.

Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 2. Defective PF lift motor 2. Defective PF main PWB.

1800 Paper feeder communication error A communication error is detected 10 times in succession.

Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB.

1900 Paper feeder EEPROM error When writing the data, the write data and the read data is not continuously in agreement 5 times.

Defective PF main PWB. Device damage of EEPROM.

18


2000 Main motor steady-state error Stable OFF is detected for 1 s continuously after main motor stabilized.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.

2010 Main motor drive error The main motor is not stabilized within 2 s after driving starts.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.

2600 PF drive motor error (paper feeder) When the PF drive motor is driven, error signal is detected continuously for 1 s.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.

3100 ISU home position error The home position is not correct when the power is turned on or at the start of copying using the table.

Defective connector cable or poor contact in the connector. Defective home position sensor. Defective ISU motor. Defective CCD PWB. Defective engine PWB.

3200 Exposure lamp error When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s.

Defective connector cable or poor contact in the connector. Defective exposure lamp. Defective CCD PWB. Defective main PWB.

3500 Communication error between scanner and ASIC An error code is detected 3 times in succession.

Defective connector cable or poor contact in the connector. Defective CCD PWB. Defective main PWB.

3600 Scanner sequence error Defective main PWB or engine PWB.

4000 Polygon motor synchronization error The polygon motor is not stabilized within 10 s after driving starts.

Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB.

4010 Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized.

Defective connector cable or poor contact in the connector. Defective polygon

19

Code Description Causes motor. Defective engine PWB.

4100 BD initialization error BD is not detected within 1 s after polygon motor stabilized.

Defective connector cable or poor contact in the connector. Defective APC PWB. Defective BD PWB. Defective main PWB.

4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB.

6000 Broken fuser heater wire The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43C/109.4F or less.

Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.

6000, 6020, 6030, 6050

Broken fuser heater wire Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature

Deformed connector pin. Defective triac.

6020 Abnormally high fuser thermistor temperature The fuser thermistor detects a temperature higher than 230C/446F continuously for 40 ms. High fuser temperature signal detects a temperature of 255C/491F continuously for 40 ms.

Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB.

6030 Broken fuser thermistor wire A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up.

Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Defective fuser thermistor. Defective engine PWB.

6050 Abnormally low fuser thermistor temperature As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60C/140F or greater is detected for one second.

Deformed connector pin. Defective triac. Defective fuser thermistor Defective fuser heater. Defective engine PWB.

6400 Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 3 s.

Defective connector cable or poor contact in the connector Defective power source PWB or engine PWB.

7800 Broken external thermistor wire The thermistor output value is 0.3 V or less.

Defective connector cable or poor contact

20

Code Description Causes in the connector. Defective temperature sensor.

7810 Short-circuited external thermistor wire The thermistor output value is 3 V or more.

Defective connector cable or poor contact in the connector. Defective temperature sensor.

7900 Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.

Defective connector cable or poor contact in the connector. Defective drum unit.

7910 Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.

Defective connector cable or poor contact in the connector. Defective developer unit.

8030 Tray upper limit detection problem (document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected.

Defective connector cable or poor contact in the connector. Defective tray upper limit sensor, paper surface sensor 1/2. Defective DF main PWB.

8040 Belt problem (document finisher) The belt sensor does not turn on/off within specified time of the belt solenoid turning on.

Defective connector cable or poor contact in the connector. Defective belt sensor. Defective belt solenoid. Defective DF main PWB.

8140 Tray elevation motor problem (document finisher) The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated.

Defective connector cable or poor contact in the connector. Defective connector cable or poor contact in the connector. The tray elevation motor malfunctions. Defective tray lower limit sensor, paper surface sensor 1/2. Defective DF main PWB.

8210 Stapler problem (document finisher) Jam 7012 or 7023 is indicated.

Defective connector cable of staple or poor contact in the connector. The stapler is blocked with a staple. The stapler is broken Defective DF main PWB.

8320 Adjustment motor 2 problem (document finisher) Defective connector

21

Code Description Causes The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on.

cable or poor contact in the connector. Defective adjustment sensor 2. Defective adjustment motor 2. Defective DF main PWB.

8330 Adjustment motor 1 problem (document finisher) The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on.

Defective connector cable or poor contact in the connector. Defective adjustment sensor 1. Defective adjustment motor 1.

8350 Roller motor problem (document finisher) The roller sensor does not turn on/off within specified time of the roller motor turning on.

Defective DF main PWB. Defective connector cable or poor contact in the connector. Defective roller sensor. Defective roller motor. Defective DF main PWB.

8360 Slide motor problem (document finisher) The slide sensor does not turn on/off within specified time of the slide motor turning on.

Defective connector cable or poor contact in the connector. Defective slide sensor. Defective slide motor. Defective DF main PWB.

8460 EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed.

Defective EEPROM or DF main PWB.

8800 Document finisher communication error A communication error is detected 10 times in succession.

Defective connector cable or poor contact in the connector Defective DF main PWB. Defective engine PWB.

8830 Bridge communication error (document finisher) A communication error is detected 10 times in succession.

Defective connector cable or poor contact in the connector. Defective bridge PWB. Defective engine PWB.

8990 Document finisher communication error Defective connector cable or poor contact in the connector. Defective DF main PWB. Defective bridge PWB.

9000 Document processor communication error A communication error is detected 10 times in succession.

Defective connector cable or poor contact in the connector. Defective DP main PWB.

9060 DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.

Defective DP main PWB. Device damage of

22

Code Description Causes EEPROM.

9500 BRU communication error IPU PWB error

9510 BRU PWB error IPU PWB error

9520 BRU PWB data error IPU PWB error

9530 Machine No.backup error C IPU PWB error

9540 Machine No.backup error D IPU PWB error

9550 Machine No.backup error E IPU PWB error

F000 Main PWB - operation panel PWB communication error Defective main PWB. Defective operation panel PWB.

F010, F011, F012, F013

Main PWB checksum error Defective main PWB.

F040 Main PWB - print engine communication error Defective main PWB. Defective engine PWB.

F050 Print engine ROM checksum error Defective engine PWB.

TASKalfa 255 - Portugus


0030 Controle FAX erro do sistema PWB processamento com o software de fax foi desativada devido a um problema de hardware.

Defeituoso PWB controle FAX.

0060 Tipo PWB Motor erro Defeito sub motor PCB.

0070 Controle FAX PWB erro de deteco incompatvel deteco anormal de controle FAX incompatibilidade PWB Na comunicao inicial com o PWB de controle FAX, qualquer comando normal de comunicao no transmitida.

Software FAX defeito defeituoso PWB controle FAX.

0100 Erro do dispositivo de memria de backup Memria flash danificada.

0120 Erro de dados de endereos MAC Para os dados em que o endereo MAC invlido.

PWB com defeito principal. memria flash com defeito. PWB motor com defeito.

0130 Memria de backup de erro de leitura / escrita (PWB principal) Memria flash danificada. PWB principal defeito.

0140 Erro de dados na memria de backup (PWB principal) Memria flash danificada. PWB principal defeito.

23


0150 Memria de backup de leitura / erro de gravao (PWB motor) Detectando PWB motor erro de comunicao EEPROM.

Imprpria EEPROM mecanismo de instalao PWB. PWB motor com defeito. danos Dispositivo de EEPROM.

0160 Erro de dados na memria de backup (PWB do motor) Memria flash danificada. PWB motor com defeito.

0170 Erro de contagem de faturamento Um erro de checksum detectado nos principais motores de memrias e de backup para os contadores de faturamento.

Danificar os dados da EEPROM. defeituoso PWB.

0180 Nmero da mquina incompatibilidade nmero Mquina de principal e do motor no corresponde.

Danificar os dados da EEPROM.

0320 I / O erro de comunicao CPU Um erro de comunicao 10 vezes seguidas.

PWB com defeito.

0630 DMA de transmisso de erro DMA de dados de imagem no completar dentro do perodo de tempo especificado.

Mau contato nos terminais do conector.PWB principal defeito.

0800 Erro de processamento de imagem JAM05 detectado duas vezes.

PWB principal defeito.

0830 Controle FAX erro de checksum rea programa de flash PWB Ocorreu um erro de soma de verificao com o programa do PWB de controle FAX.

FAX software defeituoso. controle FAX defeituoso PWB

0840 Falhas de RTC O tempo julgado para voltar com base na comparao do tempo RTC eo tempo atual ou cinco anos ou mais se passaram.

A bateria desligado do PWB principal. PWB principal defeito.

0870 Controle FAX PWB para PWB principal erro de transferncia de dados de alta capacidade de transferncia de dados de alta capacidade entre o PWB de controle FAX eo principal PWB da mquina no foi realizada normalmente, mesmo que a transferncia de dados foi repetida nos horrios especificados.

Imprpria PWB controle FAX instalao. controle FAX defeituoso ou PWB PWB principal.

0920 Erro do sistema de arquivos Fax Os dados de backup no mantida por anomalia do sistema de arquivos de memria flash do PWB de controle FAX.

Defeituoso PWB controle FAX.

1.010 Levante erro do motor Aps cassete 1 inserido, sensor elevador no ligar dentro de 12 s. Este erro detectado quatro vezes sucessivamente.

Defeituoso mecanismo fundo placa elevao na cassete. cabo conector defeituoso ou mau contato no conector. defeituoso sistema de transmisso da unidade do motor de elevao. motor do elevador com defeito. PWB motor com defeito.

24


1.020 PF erro motor de elevao (alimentador de papel) Aps cassete 2 est inserido, PF sensor de elevador 1 no ligar dentro de 12 s. Este erro detectado quatro vezes sucessivamente.

Defeituoso mecanismo fundo placa elevao na cassete. cabo conector defeituoso ou mau contato no conector. sistema de transmisso de unidade defeituosa do elevador do motor PF 1. defeituoso PF motor de elevao 1. PWB principal defeito PF.

1.030 PF erro motor de elevao (alimentador de papel) Aps cassete 3 est inserido, PF sensor de elevador 2 no ligar dentro de 12 s. Este erro detectado quatro vezes sucessivamente.

Defeituoso mecanismo fundo placa elevao na cassete. cabo conector defeituoso ou mau contato no conector. sistema de transmisso de unidade defeituosa do elevador do motor PF 2. defeituoso PF motor do elevador 2. PWB principal defeito PF.

1.800 Alimentador de papel erro de comunicao Um erro de comunicao 10 vezes seguidas.

Alimentador de papel imprprio instalao. cabo conector defeituoso ou mau contato no conector. PWB motor com defeito. PWB principal defeito PF.

1.900 Erro de EEPROM alimentador de papel Ao escrever os dados, os dados de gravao e leitura de dados no continuamente de acordo 5 vezes.

Defeituoso PF PWB principal. danos Dispositivo de EEPROM.

2.000 Motor principal de estado estacionrio erro Estvel OFF for detectada por um s continuamente aps motor principal estabilizado.

Defeito no cabo conector ou mau contato no conector. defeituoso sistema de transmisso da unidade do motor principal. motor principal com defeito. PWB motor com defeito.

2.010 Principal erro acionamento do motor O motor principal no estabilizado dentro de 2 s aps o incio da conduo.

Defeito no cabo conector ou mau contato no conector. defeituoso sistema de transmisso da unidade do motor

25

Cdigo Descrio Causas principal. motor principal com defeito. PWB motor com defeito.

2.600 PF dirigir erro motor (alimentador de papel) Quando a PF conduzir motor acionado, o sinal de erro detectado continuamente por 1 s.

Defeito no cabo conector ou mau contato no conector. sistema de transmisso de unidade defeituosa do motor de acionamento PF. defeituoso PF conduzir motor. PWB principal defeito PF.

3100 ISU erro posio inicial A posio inicial no correto quando a alimentao ligada ou no incio de copiar usando a tabela.

Defeito no cabo conector ou mau contato no conector. sensor de posio inicial com defeito. motora defeituoso ISU. CCD defeituoso PWB. PWB motor com defeito.

3200 Exposio de erro lmpada Quando o valor de entrada no momento do funcionamento da lmpada de exposio no exceda o valor limiar entre 5 s.

Defeito no cabo conector ou mau contato no conector. lmpada de exposio com defeito. Defeito PWB CCD. PWB principal defeito.

3500 Erro de comunicao entre o leitor eo ASIC Um cdigo de erro detectado trs vezes seguidas.

Defeito no cabo conector ou mau contato no conector. defeituoso PWB CCD. PWB principal defeito.

3600 Erro de sequncia Scanner PWB principal defeituoso ou PWB motor.

4000 Polygon erro de sincronizao do motor O motor polgono no est estabilizado dentro de 10 s aps o incio da conduo.

Defeito no cabo conector ou mau contato no conector. motora polgono com defeito. PWB motor com defeito.

4010 Motora Polygon estado estacionrio erro Estvel OFF for detectada por um s continuamente aps o motor polgono estabilizado.

Defeito no cabo conector ou mau contato no conector. motora polgono com defeito. PWB motor com defeito.

4100 BD erro de inicializao BD no detectado dentro de um s depois do motor polgono estabilizado.

Cabo conector com defeito ou mau contato no conector.

26

Cdigo Descrio Causas defeituoso APC PWB. defeituoso BD PWB. PWB principal defeito.

4700 VIDEO ASIC erro de dispositivo Defeito no cabo conector ou mau contato no conector. PWB principal defeituoso ou PWB motor.

6000 Fio de aquecimento do fusor quebrado A temperatura detectada de fusor termistor no atinge a temperatura especificada (temperatura indicao pronto) aps o aquecedor do fusor foi ligado continuamente por 60 s no aquecimento. A temperatura de fuso em 7 segundos e 20 segundos desde o controle de temperatura de fuso ocorreu difere de 43 C / 109,4 F ou menos.

Defeito no cabo conector ou mau contato no conector. pinos Deformed. triac com defeito. Fuser termostato acionado. fio aquecedor do fusor quebrado. PWB motor com defeito.

6000, 6020, 6030, 6050

Fio de aquecimento do fusor quebrado anormalmente alta temperatura do fusor termistor do fusor quebrado fio termistor anormalmente baixa temperatura do fusor termistor

Pin conector deformado. triac com defeito.

6020 Anormalmente elevada temperatura do fusor termistor O termistor de fuso detecta uma temperatura superior a 230 C / 446 F continuamente por 40 ms. Sinal de alta temperatura de fuso detecta uma temperatura de 255 C / 491 F continuamente por 40 ms.

Pin Deformed conector. triac com defeito. Shorted termistor do fusor. PWB motor com defeito.

6030 Quebrado fio fusor termistor valor A / D do termistor do fusor superior a 251 bit continuamente por 7 s durante o aquecimento.

Defeito no cabo conector ou mau contato no conector. pinos Deformed. triac com defeito. fusor termistor com defeito. PWB motor com defeito.

6050 Anormalmente baixa temperatura de fuso termistor medida que a temperatura estvel atingiu o segundo tempo, a diminuio na temperatura de fuso do termistor de 60 C / 140 F ou superior detectado por um segundo.

Pin Deformed conector. triac com defeito. Defeito termistor do fusor fusor aquecedor com defeito. PWB motor com defeito.

6400 Erro sinal zero-cross Enquanto o controle do aquecedor de fuso realizada, o sinal zero-cross no de entrada dentro de 3 s.

Cabo conector com defeito ou mau contato no conector defeituoso PWB fonte de energia ou motor PWB.

7800 Fio termistor externo quebrado O valor de sada do termistor de 0,3 V ou menos.

Defeito no cabo conector ou mau contato no conector. sensor de temperatura

27

Cdigo Descrio Causas com defeito.

7810 Fio termistor externo em curto-circuito O valor de sada do termistor de 3 V ou mais.

Defeito no cabo conector ou mau contato no conector. sensor de temperatura com defeito.

7900 Unidade do tambor EEPROM erro Nenhuma resposta emitida a partir do dispositivo de leitura / escrita para 5 ms ou mais e este problema repetido cinco vezes sucessivamente. Incompatibilidade de leitura de dados a partir de dois locais ocorre oito vezes sucessivamente. Incompatibilidade entre os dados de escrita e leitura de dados ocorre oito vezes sucessivamente.

Defeito no cabo conector ou mau contato no conector. cilindro com defeito.

7910 Unidade desenvolvedor erro EEPROM Nenhuma resposta emitida a partir do dispositivo em leitura / escrita para 5 ms ou mais e este problema repetido cinco vezes sucessivamente. Incompatibilidade de leitura de dados a partir de dois locais ocorre oito vezes sucessivamente. Incompatibilidade entre os dados de escrita e leitura de dados ocorre oito vezes sucessivamente.

Defeito no cabo conector ou mau contato no conector. desenvolvedor defeituoso unidade.

8030 Bandeja problema de deteco de limite superior (finalizador de documentos) Quando o motor de elevao da bandeja levanta uma bandeja, o estado ON do sensor de limite superior da bandeja detectado.

Defeito no cabo conector ou mau contato no conector. bandeja com defeito sensor de limite superior, sensor de superfcie de papel 1/2. PWB principal defeito DF.

8040 Problema Belt (finalizador de documentos) O sensor de cinto no ligar / desligar dentro do tempo especificado do solenide cinto de ligar.

Defeito no cabo conector ou mau contato no conector. sensor de cinto com defeito. solenide cinto com defeito. PWB principal defeito DF.

8140 Bandeja problema do motor de elevao (finalizador de documentos) O sensor de limite ou superfcie do papel baixo sensor de bandeja 1/2 no pode ser detectado estar no prazo de 10 s, uma vez que o motor de elevao da bandeja ativado.

Defeito no cabo conector ou mau contato no conector. cabo conector defeituoso ou mau contato no conector. As disfunes motoras elevao bandeja. sensor de limite de bandeja com defeito menor, sensor de superfcie de papel 1/2. PWB principal defeito DF.

8210 Problema grampeador (finalizador de documentos) Jam 7012 ou 7023 indicado.

Cabo conector defeituoso de grampo ou mau contato no conector. O grampeador est

28

Cdigo Descrio Causas bloqueada com um grampo. O grampeador est quebrado principal PWB defeituoso DF.

8320 Ajuste do motor 2 problema (finalizador de documentos) O sensor de ajuste 2 no ligar / desligar dentro do tempo especificado do motor de ajuste 2 de ligar.

Defeito no cabo conector ou mau contato no conector. sensor de ajuste defeituoso 2. motor de ajuste defeituoso 2. PWB principal defeito DF.

8330 Motor de Ajuste 1 problema (finalizador de documentos) O sensor de ajuste 1 no ligar / desligar dentro do tempo especificado do motor de ajuste 1 ligar.

Cabo conector com defeito ou mau contato no conector. sensor de ajuste defeituoso 1. motor de ajuste defeituoso 1.

8350 Problema de motor Roller (finalizador de documentos) O sensor de rolo no ligar / desligar dentro do tempo especificado do motor do rolo de ligar.

Defeituoso principal PWB DF. cabo conector defeituoso ou mau contato no conector. sensor de rolo com defeito. motor de rolo com defeito. PWB principal defeito DF.

8360 Deslize problema motor (finalizador de documentos) O sensor de slide no ligar / desligar dentro do tempo especificado do motor deslizante de ligar.

Defeito no cabo conector ou mau contato no conector. sensor de slides com defeito. motor de slides com defeito. PWB principal defeito DF.

8460 Problema EEPROM (finalizador de documentos) de leitura ou gravao de EEPROM no pode ser realizada.

EEPROM com defeito ou principal PWB DF.

8800 Erro de comunicao finalizador de documentos Um erro de comunicao 10 vezes seguidas.

Defeito no cabo conector ou mau contato no conector defeituoso DF PWB principal. PWB motor com defeito.

8830 Ponte erro de comunicao (finalizador de documentos) Um erro de comunicao 10 vezes seguidas.

Defeito no cabo conector ou mau contato no conector. PWB ponte com defeito. PWB motor com defeito.

8990 Documento erro de comunicao finisher Defeito no cabo

29

Cdigo Descrio Causas conector ou mau contato no conector. defeito principal PWB DF. PWB ponte com defeito.

9000 Processador de documentos erro de comunicao Um erro de comunicao 10 vezes seguidas.

Defeito no cabo conector ou mau contato no conector. defeito principal PWB DP.

9060 No DP erro EEPROM ler e gravar dados no coincidem. Dados na rea especificada da memria de segurana no coincide com os valores especificados.

Defeituoso principal PWB DP. danos Dispositivo de EEPROM.

9500 Erro de comunicao BRU Erro IPU PWB

9510 Erro BRU PWB Erro IPU PWB

9520 Dados de erro BRU PWB Erro IPU PWB

9530 Mquina de erro No.backup C Erro IPU PWB

9540 Erro da mquina No.backup D Erro IPU PWB

9550 Erro da mquina No.backup E Erro IPU PWB

F000 PWB principal - operao de erro de comunicao da consola PWB PWB principal defeito. painel PWB funcionamento defeituoso.

F010, F011, F012, F013

Principal erro PWB de checksum PWB principal defeito.

F040 PWB principal - impresso erro de comunicao do motor PWB principal defeito. PWB motor com defeito.

F050 Mecanismo de impresso de erro de checksum da ROM PWB defeito do motor.

FSC2026MFP/FSC2626MFP - English


0030 FAX control PWB system error Processing with the fax software was disabled due to a hardware problem.


0070 FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.

Defective FAX software.PWB. Defective FAX control PWB.

30


0100 Backup memory device error Defective flash memory. Defective main PWB.

0120 MAC address data error For data in which the MAC address is invalid.

Defective flash memory. Defective engine PWB.

0130 Backup memory read/write error (main PWB) Defective flash memory. Defective main PWB.

0140 Backup memory data error (main PWB) Defective flash memory. Defective main PWB.

0150 Engine PWB EEPROM error Detecting engine PWB EEPROM communication error.

Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM.

0170 Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters.

Data damage of EEPROM. Defective PWB.


Data damage of EEPROM.

0600 Expanded memory (DIMM) installing error The expansion memory modules (DIMM) are not correctly mounted.

Improper installation expanded memory (DIMM).

0610 Expanded memory (DIMM) error The expansion memory modules (DIMM) mounted on the main PWB does not operate correctly.

Defective expanded memory (DIMM). Defective main PWB.

0640 Hard disk error The hard disk cannot be accessed.

Defective hard disk. Defective main PWB.

0830 FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.

Defective FAX software. Defective FAX control PWB.

0840 Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.

The battery is disconnected from the main PWB. Defective main PWB.

0870 FAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times.

Improper installation FAX control PWB. Defective FAX control PWB or main PWB.

0920 Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.


0930 EEPROM bus error Defective drum PWB (EEPROM). Defective engine PWB (EEPROM). Defective engine PWB. Defective main PWB.

1010 Lift motor error When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened

Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB.

31

Code Description Causes and closed, the cassette installed confirmation message is displayed 5 times successively.

1020 PF lift motor error (paper feeder 1) When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively.

Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.

1030 PF lift motor error (paper feeder 2) When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively.

Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.

1500 PF heater 1 high temperature error (paper feeder 1) A temperature higher than 75C/167F is detected.

Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB.



1520 PF heater 1 high temperature error (paper feeder 2) A temperature higher than 75aC/167F is detected.




1600 PF heater 1 low temperature error (paper feeder 1) An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on.

Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB.





1630 PF heater 2 low temperature error (paper feeder 2) An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is

Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly.

32

Code Description Causes turned on. Defective PF thermistor 2. Broken PF

heater 2. Defective PF heater PWB or PF main PWB.

1800 Paper feeder communication error Communication error between engine PWB and optional paper feeder.

Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB.

2100 Developing motor error The developing motor ready input is not given for 5 s during the main motor is ON.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing motor. Defective developing motor. Defective engine PWB.

2200 Drum motor error The drum motor ready input is not given for 5 s during the drum motor is ON.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the drum motor. Defective drum motor. Defective engine PWB.

2330 Fuser pressure release motor error When the fuser pressure release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB.

2340 Fuser pressure release motor time-out error When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB.

2500 Paper feed motor error The drum motor ready input is not given for 5 s during the paper feed motor is ON.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the paper feed motor. Defective paper feed motor. Defective engine PWB.

2600 PF paper feed motor error (paper feeder 1) The drum motor ready input is not given for 2 s during the PF paper feed motor is ON.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB.

2610 PF paper feed motor error (paper feeder 2) The drum motor ready input is not given for 2 s during the PF paper feed motor is ON.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB.

2730 Developing release motor error When the developing release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing release motor. Defective developing release motor. Defective engine PWB.

2740 Developing release motor time-out error When the developing release motor is driven, the developing release switch (DEVRSW) is not detectable for 1 s.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing release motor. Defective developing release motor. Defective engine PWB.

33


2820 Fuser motor error The fuser motor ready input is not given for 5 s during the fuser motor is ON.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser motor. Defective fuser motor. Defective engine PWB.

3100 ISU home position error The home position is not correct when the power is turned on or at the start of copying using the table.

Defective connector cable or poor contact in the connector. Defective home position sensor. Defective ISU motor. Defective CCD PWB. Defective main PWB.

3200 Exposure lamp error When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s.

Defective connector cable or poor contact in the connector. Defective exposure lamp. Defective inverter PWB or CCD PWB. Defective main PWB.


Defective connector cable or poor contact in the connector. Defective exposure lamp. Defective inverter PWB or CCD PWB. Defective main PWB.

3500 Communication error between scanner and ASIC An error code is detected.

Defective connector cable or poor contact in the connector. Defective CCD PWB. Defective main PWB.

4001 Polygon motor KM error The polygon motor KM ready input is not given for 10 s during the polygon motor is ON.

Defective connector cable or poor contact in the connector. Defective polygon motor KM. Defective engine PWB.

4002 Polygon motor CY error The polygon motor CY ready input is not given for 10 s during the polygon motor is ON.

Defective connector cable or poor contact in the connector. Defective polygon motor CY. Defective engine PWB.

4201 Laser output error (black) The pin photo signal is not output from PD PWB K for one second while laser is emitted.

Defective connector cable or poor contact in the connector. Defective APC PWB K. Defective PD PWB K. Defective engine PWB.

4202 Laser output error (cyan) The pin photo signal is not output from PD PWB C for one second while laser is emitted.

Defective connector cable or poor contact in the connector. Defective APC PWB C. Defective PD PWB C. Defective engine PWB.

4203 Laser output error (magenta) The pin photo signal is not output from PD PWB M for one second while laser is emitted.

Defective connector cable or poor contact in the connector. Defective APC PWB M. Defective PD PWB M. Defective engine PWB.

4204 Laser output error (yellow) The pin photo signal is not output from PD PWB Y for one second while laser is emitted.

Defective connector cable or poor contact in the connector. Defective APC PWB Y. Defective PD PWB Y. Defective engine PWB.

4600 LSU cleaning motor error When the LSU cleaning motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective drive transmission system of the LSU cleaning motor. Defective LSU cleaning motor. Defective engine PWB.

4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB.

34


5301 Broken cleaning lamp K wire When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB.

5302 Broken cleaning lamp C wire When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective cleaning lamp C. Defective engine PWB.

5303 Broken cleaning lamp M wire When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective cleaning lamp M. Defective engine PWB.

5304 Broken cleaning lamp Y wire When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.

Defective connector cable or poor contact in the connector. Defective cleaning lamp Y. Defective engine PWB.

6000 Broken fuser heater wire The detected temperature of fuser thermistor does not rise 1aC/1.8aF after the fuser heater has been turned on continuously for 10 s in warming up. The fuser temperature does not reach 100aC/212aF after the fuser heater has been turned on continuously for 30 s in warming up. The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The detected temperature of fuser thermistor does not rise 1aC/1.8aF after the fuser heater has been turned on continuously for 10 s during printing.

Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.

6020 Abnormally high fuser thermistor temperature The fuser thermistor detects a temperature higher than 240C/464F. By the activation of the high temperature error detection circuit (230C/446F or more) of fuser thermistor, the illumination of fuser heater was forcibly turned off and 10 s has elapsed.

Shorted fuser thermistor. Defective engine PWB.

6030 Broken fuser thermistor wire Input from fuser thermistor is 3 or less (A/D value) continuously for 1 s.

Defective connector cable or poor contact in the connector. Broken fuser thermistor

Documents

Kyocera Mita - Trouble Error Codes List