L441/ L444 Four-Post LiftFour-Post Lift FamilyHigh-Capacity Open- and Closed-Front Alignment Lifts

Four-Post liftsAvailable in long or short, open or closed configurations.

Other

Lift18,000 Pounds!

18,000-lb. Capacity

Integrated Air Line Kit

Extra-Wide Runways

4 Accommodate wide vehicles

4 Rub rails for drive-on safety22½”

Flush Slipplates

4Wheelbases up to 158”

4 Tethered pins secure plates on basic models

Two Swing Air Jacks

4 Raise vehicles off runways

4 9,000-lb.capacity

4 12 secure positions

4 Lightweight design

Two Movable Work Steps

Louvered Ramps

4 Prevent wheel spin

4More effective than diamond tread or abrasive strips

Pins and Pulleys

4 Large diameter iron pulleys with teflon bearings ensure long life

4 Chrome-plated pins

Other

Lift18,000 Pounds!

18,000-lb. Capacity

4 Best in class!

Model L451T-IS shown

Open-Front Available on Any Configuration

4 Allows easy access to adjustment points and jacks on long- and standard-length runway racks

Integrated Air Line Kit

4 Convenient power for air tools at front and rear

Control Unit

4 Easy-to-use console

4 Powerful 3-hp motor

Louvered Locks

4 16 lock heights ensure runways are level

4 Long-life galvanized cables

Umbilical Covering

4 Strong and flexible

4 Protects air and hydraulic lines from damage

NEW!

PowerSlide® Locking System

Models L451T-PS, L454T-PS

PowerSlide® control Push-button locks or unlocks the slipplates and turnplates.

PowerSlide® slipplates Secure slipplates with a single button. The technician no longer has to struggle to remove and replace slipplate pins for every alignment.

Yesterday's technology VS.

87

654

32

1

8 Trips

15

6

Only3 Trips!

Mount targets

Make adjustments

Jack vehicle and compensate sensors

Remove targets

Remove slipplate and turnplate pins

Raise leveling legs (if equipped)

1

2

3

4

5

6

7

8

Lower leveling legs (if equipped)

Replace slipplate and turnplate pins

PowerSlide ® editionsaves time and hassle!

Trips Around the Car with PowerSlide®

PowerSlide® turnplates Save time by eliminating struggle with turnplate pins.

Models L451T-IS, L454T-IS

Fully Integrated Alignment with Inflation Station and PowerSlide®

FIA allows WinAlign® aligners to control lift features for ultimate productivity.*

* Alignment console sold separately.

FIA/Inflation Station editionmaximizes productivity!

Integrated inflation reelsAutomatically fills or bleeds each tire.

Record air pressure Printouts record starting and final pressure.

FIA console Controls PowerSlide® and Inflation Station features.

Model L451T-IS shown

Automatic locking Turnplates and slipplates lock

and unlock at the right time. Locks automatically during lift descent.

Swing Air Jacks Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations.

The heavy-duty Swing Air Jack has a capacity of 9,000 lbs. (4,082 kg) and combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles.

133-84-1 – 9,000-lb. Capacity Swing Air Jack

AlignLights systemHunter’s AlignLights lighting system provides an efficient light source underneath the vehicle.

AlignLights is powered by the main lift power source and requires no additional or exposed electrical cords.

AlignLights automatically turns off when the lift is lowered to the floor and turns on when the lift is raised.

20-2993-1 – AlignLights system for four-post lifts

Turnplates

20-2076-1 PowerSlide® turnplates with automatic bridges Two stainless steel turnplates for camera-sensor systems.

20-2075-1 PowerSlide® turnplates without automatic bridges Two stainless steel turnplates for conventional-sensor systems.

20-2532-1 Stainless steel turnplate kit Two stainless steel Delrin-ball turnplates and bolt-on guide strips.

20-2533-1 Low-friction stainless steel turnplate kit Two stainless steel Torlon ball turnplates and bolt-on guide strips.

20-2531-1 Powder-coated turnplate kit Two powder-coated, Delrin-ball turnplates and bolt-on guide strips.

Integrated bridge lowers and raises as plates are locked, making rolling compensation a snap. Air-operated control system ties directly into PowerSlide® lifts (20-2076-1 shown).

All L451T and L454T models will ship with the most appropriate turnplates. When making a substitution, any of the following turnplates may be used.

OPTIONAL

8 3/4”

(210 mm)

13’ 0”

(3962.4 mm)MINIMUMCEILINGHEIGHT

6’ 3”

(1905 mm)MAXIMUMHEIGHT

8’ 2”

(2489 mm)

L451 and L454 elevation view

Because of continuing technological advances, specifications, models and options are subject to change without notice.

Standard equipmentStainless steel turnplates (PowerSlide® turnplates on PS and IS models)Flush-mounted, full-floating slipplates (PowerSlide® slipplates on PS and IS models)Louvered ramps with built-in wheel stopsFront wheel stopsTwo wheel chocksTwo movable work stepsBuilt-in, full-length jack railsBuilt-in rub railsBuilt-in air line kit

Options20-1365-1 17.5” Ramp Extension Kit (for low-clearance vehicles) 20-2033-1 40” Ramp Extension Kit (for extremely low-clearance vehicles or high-floor-slope situation)

Standard-length specifications

JOINTFREEAREA

JOINTFREEAREA

31” BY 31”(787 mm BY

787 mm)AREA FREE

OF JOINTS INCONCRETE

(located underboth front post

baseplates)

20 1/2” BY20 1/2”

(521 mmBY

521 mm)AREAFREE

OF JOINTSIN

CONCRETE(located

underboth rear

postbaseplates)

11’- 7 3/16”(3535 mm)

9’- 10 11/16”(3015 mm)

9’- 9 3/8”(2981 mm)

12’- 3/8”(3667 mm)

15’- 3 3/8” (4658 mm)RECOMMENDED BAY WIDTH

22 1/2”(572 mm)

40”(1016 mm)

28 1/8”(714 mm)

RUNWAYLENGTH:

18’- 3”(5563 mm)

OVERALLLENGTH:

21’- 9 3/4”(6648 mm)

28 5/8”(727 mm)

18’- 10 1/4”(5747 mm)

ROOM FOR ALIGNMENT CONSOLE

HAWKEYE AND PRONTO SYSTEMS HAVE SPACE REQUIREMENTS IN

FRONT OF THE LIFT THAT MUST BE MET, REFER TO APPROPRIATE SENSOR SITE REQUIREMENTS.

31 1/2”(768 mm)

L451

4”(102 mm)

RECOMMENDEDBAY LENGTH

(For Lift with HE421Camera Sensor)

Floor-MountedSensors

(FM, ML, LC or FM)Refer to 6292-T

Typical 27’- 8 1/4”(8439 mm)

Specified Range28’- 4 1/2”

to 24’-11 1/4”(8649 mm

to 7601 mm)

For HE421CM: add 5” (127 mm)

Refer to 6291-T

For HE421WM:Spec Rangeis expanded.

Refer to 6290-T

L451 plan view

ModelsOpen-front Closed-front

L451JT L454JTStandard-length runways with (2) 9,000-lb. swing air jacks and stainless steel turnplates

L451T-PS L454T-PS

Standard-length runways with (2) 9,000-lb. swing air jacks and PowerSlide® slipplates and turnplates

L451T-IS L454T-IS

Standard-length runways with (2) 9,000-lb. swing air jacks, PowerSlide® slipplates and turnplates, Inflation Station, and FIA

Max. vehicle weight 18,000 lbs. (8164 kg)Max. wheelbase

General service 193 in. (4902 mm)Two-wheel alignment* 177 in. (4496 mm)Four-wheel alignment 158 in. (4013 mm)

Min. four-wheel alignment 88 in. (2235 mm)Max. lifting height 75 in. (1905 mm)Alignment height Any of 16 lock positionsMinimum height 8.75 in. (222 mm)Overall height 98 in. (2489 mm)Tread width

Min. inside 40 in. (1016 mm)Max. outside 85 in. (2159 mm)

Motor 3 hp, 208-230 VAC, 60 Hz, 1 ph

Air 90-150 psi (6.2-10.3 bar)* Long wheelbase vehicles may require jacking compensation.

Form 6020-T, 12/14Supersedes 6020-T, 10/14

Copyright © 2014, Hunter Engineering Company

Open-front Closed-front

L451LJT L454LJTExtended-length runways with (2) 9,000-lb. swing air jacks and stainless steel turnplates

L451LT-PS L454LT-PS

Extended-length runways with (2) 9,000-lb. swing air jacks and PowerSlide® slipplates and turnplates

L451LT-IS L454LT-IS

Extended-length runways with (2) 9,000-lb. swing air jacks, PowerSlide® slipplates and turnplates, Inflation Station, and FIA

Models

Extended-length specifications

Standard and optional equipmentIdentical to L451 and L454 Lift Racks.

1214B

L451L plan view**

** See previous page for elevation view

JOINTFREEAREA

JOINTFREEAREA

31” BY 31”(787 mm BY

787 mm)AREA FREE

OF JOINTS INCONCRETE

(located underboth front post

baseplates)

20 1/2” BY20 1/2”

(521 mmBY

521 mm)AREAFREE

OF JOINTSIN

CONCRETE(located

underboth rear

postbaseplates)

11’- 7 3/16”(3535 mm)

9’- 10 11/16”(3015 mm)

9’- 9 3/8”(2981 mm)

12’- 3/8”(3667 mm)

15’- 3 3/8” (4658 mm)RECOMMENDED BAY WIDTH

22 1/2”(572 mm)

40”(1016 mm)

28 1/8”(714 mm)

RUNWAYLENGTH:

20’- 5 1/2”(6236 mm)

OVERALLLENGTH:

24’- 6 1/4”(7474 mm)

28 5/8”(727 mm)

21’- 6 3/4”(6572 mm)

ROOM FOR ALIGNMENT CONSOLE

HAWKEYE AND PRONTO SYSTEMS HAVE SPACE REQUIREMENTS IN

FRONT OF THE LIFT THAT MUST BE MET, REFER TO APPROPRIATE SENSOR SITE REQUIREMENTS.

31 1/2”(768 mm)

L451L

4”(102 mm)

RECOMMENDEDBAY LENGTH

(For Lift with HE421Camera Sensor)

Floor-MountedSensors

(FM, ML, LC or FM)Refer to 6292-T

Typical 30’- 4 3/4”(9265 mm)

Specified Range31’- 3/4”

to 27’- 7 3/4”(9468 mm

to 8426 mm)

For HE421CM: add 5” (127 mm)

Refer to 6291-T

For HE421WM:Spec Rangeis expanded.

Refer to 6290-T

Be sure to check out other Hunter literature for more quality products from Hunter Engineering.

* Long wheelbase vehicles may require jacking compensation.

Max. vehicle weight 18,000 lbs. (8164 kg)Max. wheelbase

General service 227 in. (5766 mm)Two-wheel alignment* 211 in. (5360 mm)Four-wheel alignment 158 in. (4013 mm)

Min. four-wheel alignment 88 in. (2235 mm)Max. lifting height 75” (1905 mm)Alignment height Any of 16 lock positionsMinimum height 8.75 in. (222 mm)Overall height 98 in. (2489 mm)Tread width

Min. inside 40 in. (1016 mm)Max. outside 85 in. (2159 mm)

Motor 3 hp, 208-230 VAC, 60 Hz, 1 ph

Air 90-150 psi (6.2-10.3 bar)

Because of continuing technological advances, specifications, models and options are subject to change without notice.