Upload
shavarsh-yeprikyan
View
154
Download
48
Tags:
Embed Size (px)
Citation preview
SERVICE MANUAL
LCD COLOUR TELEVISION
MODEL
CHAPTER 1. SPECIFICATIONS………….….…………………………………………………….1
CHAPTER 2. REMOVING OF MAJOR PARTS…………..……………………………………….3
CHAPTER 3. ADJUSTMENT PROCEDURE……………..……………………………………….7
CHAPTER 4. TROUBLESHOOTING TABLE………...…….……………………………...…….18
CHAPTER 5. MAJOR IC INFORMATIONS……….....….........…………………………...……..35
CHAPTER 6. BLOCK DIAGRAM/ WIRING DIAGRAM……..…….……………………..……..46
CHAPTER 7. PRINTED WIRING DIAGRAM…..…………...……………………………………49
CHAPTER 8. SCHEMATIC DIAGRAM………..………………..………………………...………53
CHAPTER 9. EXPLODED PARTS & PARTS GUIDE ……….……..………………………66
LC-22LE420M
This document has been published to be used for after sales service only.
The contents are subject to change without notice.
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
In the interests of user-safety(Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
1
CHAPTER 1. SPECIFICATIONS [1] SPECIFICATIONS
Item Model: LC-22LE420M
LCD screen size 21.5”
Resolution 2,073,600 pixels(1920x1080)
TV-standard PAL: B/G, D/K, I SECAM: B/G, D/K, K/K1 NTSC: M
VHF/UHF 44.25 — 863.25 MHz Receiving
channel CATV S1 — S41ch (including Hyperband)
TV-Tuning System Auto Preset 99 ch
TV
function
STEREO/BILINGUAL NICAM: B/G, I, D/K A2 stereo: B/G
Audio out 3W*2 16ohm
ANT./CABLE UHF/VHF 75 ohm DIN type
INPUT2 HDMI in with HDCP (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
1080I/60Hz, 1080P/50Hz, 1080P/60Hz, 1080P/24Hz)
INPUT3 AUDIO in , COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz,1080I/
50Hz,1080I/60Hz)
OUTPUT VIDEO out, AUDIO out
INPUT5 PC IN Analog RGB (PC) in (15-pin mini D-sub female connector)
Rear
Audio IN PC/HDMI Audio in (Ø 3.5mm jack)
Headphone out Headphone out
INPUT1 HDMI in with HDCP (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
1080I/60Hz, 1080P/50Hz, 1080P/60Hz, 1080P/24Hz)
INPUT4 VIDEO in, AUDIO in
Terminal
Side
USB Photo/Music/Video mode, Software update
OSD language English, Portuguese, Russian, Arabian, Persian, Thailand, Indonesian, Vietnamese, French, Chinese(simplified)
Power Requirement AC 110V ~240V / 50/60 Hz
Power Consumption 35W(1W Standby)
TV + stand 5.4kg Weight
TV only 4.8 kg
TV + stand 532.8/383.9/187.9mm Dimension
(W/H/D) TV only 532.8/350.3/44.2mm
Operating Temperature 0°C — 45°C
[2] DIMENSIONS and VESA wall mount
2
3
CHAPTER 2. Removing of Major Parts Step 1. Remove the BASE ASSY, after loose 4 screws,
Step 2. Remove AC COVER, after loose 10 screws,
Step 3. Remove BACK COVER, after loose 1 screw,
.
4
Step 4. Remove LVDS CABLE and SPEAKER, after remove 2 yellow tapes and disconnect 4 connectors,
Step 5. Remove the base support and 2 top vesa, after loose 8 screws and remove 2
foils.
5
Step 6. Remove KEY ASSY/ IR BD/ IR&KEY CABLE, after loose 3 screws and disconnect 2 cables.
Step 7. Remove POWER BD and MAIN BD with EMI shielding, after loose 12 screws.
6
Step 8. Get the panel with main chassis away front bezel.
Step 9. Remove MAIN CHASSIS, after loose 4 screws at left and right side.
7
CHAPTER 3. ADJUSTMENT PROCEDURE
[1]ADJUSTMENT PROCEDURE
1. Main Menu (The default value is marked in red)
Layer1 Layer2 Layer3 Layer4 Layer5 Remark
User
Standard When
Location=Home
Dynamic When
Location=Store
Movie
AV mode
Power Saver
Backlight
0~100 Only Adaptive
Backlight is "Off"
Or in VGA
Brightness 0~100
Contrast 0~100
Saturation 0~100
Hue -50~50
Sharpness -10~10
In VGA, this item
is hidden
Off Adaptive Luma
Control On
User
Cool When AV
Mode=Dynamic
Standard When AV
Mode=Standard
Color
Temperature
Warm
R Gain 0~255
G Gain 0~255
Color
Temperature
B Gain 0~255
Off
Video
Advanced Video Adaptive
Backlight On
VGA except
8
Off
Low
Medium
Strong
DNR
Auto
Off Flesh Tone
On
Auto
Graphic HDMI Mode
Video
Only enable in
HDMI 480p, 576p,
720p, 1080p
Auto Adjust
H.Position 50~50
V.Position -20~20
Phase -20~20
VGA
Clock -90~90
VGA only
Balance -50~50(0)
Bass 0~100(50)
Treble 0~100(50)
Surround On/Off
Equalizer Off/Rock/Pop/Live
/Classic
Speaker On/Off
Audio
Audio Select Auto/HDMI/PC
Line In
HDMI only
Audio Channel Mono/Stereo/Dual
1/Dual2
Color System Auto/PAL/SECAM
/NTSC
Sound System B/G / I / D/K / M
Scan All
Channels.
Status:Scanning
…/Scan
Complete(Chann
el not found)/Scan
Cancel
TV
Channels Channel Scan
Channel Scan
Frequency:
TV only
9
Analog Channels:
Color System Auto/PAL/SECAM
/NTSC
Sound System B/G / I / D/K / M
Scan All
Channels.
Status:Scanning
…/Scan
Complete(Chann
el not found)/Scan
Cancel
Frequency:
Update Scan
Channel Scan
Analog Channels:
Search for analog
channels
Start Frequency
(MHz)
End Frequency
(MHz)
Scan All
Channels.
Status:Scanning
…/Scan
Complete/Scan
Cancel
Frequency:
Analog Manual
Scan
Start Search
Analog Channels:
Channel Number:
Channel Name:
Frequency
Color System Auto/PAL/SECAM
/NTSC
Sound system B/G / I / D/K / M
Channel Number:
Channel Name:
Finetune
Frequency:
Channel Edit
(Next page is
Channel list)
[
Num.
Type
Freq.
System
Name Skip On/Off
10
Analog
Swap
Insert
Delete
]
Store
Are you sure?
(Confirm dialog)
Clean Channel
List
Are you sure?
(Confirm dialog) OK/Cancel
R
G
Y
B
Favorite Channels
All data clear Are you sure?
(Confirm dialog) OK/Cancel
English
简体中文 العربیة
Français ไทย Português Việt Nam Bahasa Indonesia Русский
OSD Language
فارسیNormal
Panorama
Full
Zoom
Underscan
Cinema
View Mode
Dot by Dot
Available options
depend on input
timing.
Date Time Power On Timer Off/On/Once Timer
Setup
Time Setup Time
Power Off Timer Off/On/Once
11
Timer
Off 10 Minutes 20 Minutes 30 Minutes 40 Minutes 50 Minutes 60 Minutes 90 Minutes
Sleep Timer
120 Minutes Off 1 Hour 2 Hours
Auto Sleep
5 Hours DivX(R)Registrati
on
You must register
your device to
play DivX
protected videos.
Registration
Code:532J7VZU
DF
Register at
http://vod.divx.co
m
DivX(R)
Deregistration
Deregistration
code:5DCF8NHI
Deregister at
http://vod.divx.co
m
Continue with
registration?
(OK/Cancel)
You must register
your device to
play DivX
protected videos.
Registration
Code:532J7VZU
DF
Register at
http://vod.divx.co
m
(OK)
WEST EUR Teletext Decoding Page
Language Arab
12
Farsian Home
Location Store Model Name: Version:
Version Info
Release Date:
Reset Default Are you sure?
(Confirm dialog) OK/Cancel
Password Channel Block Analog Block/UnBlock
TV Block/UnBlock INPUT1 HDMI1 Block/UnBlock INPUT2 HDMI2 Block/UnBlock INPUT3 COMP Block/UnBlock INPUT4 AV Block/UnBlock
Input Block
INPUT5 PC IN Block/UnBlock New Password
Change
Password Confirm
Password
Parental
Clean All Are you sure?
(Confirm dialog) OK/Cancel
2. Display adjustment Only adjust HDMI Mode and copy to all of input source
General set-up:
Equipment Requirements: Minolta CA-210 or Equivalent Color analyzer or equivalent instrument.
Input Signal Type:
1. Internal full white pattern.
2. Select Picture mode to Standard mode and check the x, y data. Input Injection Point: HDMI cable
Alignment method:
Initial Set-up:
1. Select source as “INPUT1 HDMI1”.
13
2. Set Picture mode as “Standard”.
3. Enter factory mode menu: press MENU + Numeric keys “3481” .
Alignment:
1. Press “Menu” key enter factory mode page.
2. Set VideoWhite Pattern to “Medium”.
3. Enter VideoColor Temperature adjust.
Color temperature adjust:
1. Set color temperature to “Cool”
2. Adjust R Gain/G Gain values to meet “Cool” color coordinates.(Keep B Gain set “128”)
3. Adjust R Offset/G Offset values to meet “Cool” color coordinates.(Keep B Offset set “128”)
4. Repeat step 2, 3, 4 twice to meet “Cool” color coordinates specification below.
5. Set color temperature to “Warm”、”Standard” then Repeat 2,3,4 step adjusting.
6. Set color temperature “User” mode then set all values to “128”
Chromaticity Coordinate Mode
x y
COOL 0.272 ± 0.01 0.277 ± 0.01
STANDARD 0.285 ± 0.01 0.293 ± 0.01
WARM 0.313 ± 0.01 0.323 ± 0.01
Customer Color Panel Native Color Temperature
Check the 16 grayscale pattern should be distinguished and color bar is correct
Reset AV setting in OSD menu, picture mode shall be recalled to be “Standard” mode.
Note:
1. After the main board or LCD panel is replaced, need to perform Display adjustment.
2. Use Minolta CA-210 for color coordinates and luminance check.
3. Before adjusting, all colour analyzers (CA-210) should be coordinates with a same reference TV
set.
4. Luminance > =200 cd/m2 (LC-22LE420M) in the center of the screen when Brightness control at
50, Contrast control at 100, Backlight control at 100.
[2] SERVICE MODE
Enter factory mode menu: press MENU + Numeric keys “3481” to enter factory mode.
14
You can press “RETURN” key to back to normal main menu.
[3] SOFTWARE UPGRADE PROCEDURE 1. Connect to TV USB port to upgrade the software firmware
Please follow the following steps to upgrade the firmware.
I. Turn on TV.
II. Press Menu, select SetupVersion info to check "Version"
III. Copy the correct software firmware (*.pkg) to USB disk.
Ex: Version: VG224G_PA_V2.00, copy VG224G.pkg to USB disk.
IV. Insert the USB disk to TV USB port.
V. TV AC power off -> AC power on
VI. V. TV will upgrade by itself after detect the USB disk condition and the content of the pkg file.
Note: TV's LED will flash during upgrade process
VII. After finish upgrade process, TV will reboot by itself.
VIII. Remove USB disk from TV.
IX. Press Menu, select SetupVersion info.
X. Check the software version is correct or not.
15
[4] Remote control function Function Testing Remote control unit
1. POWER
Switch the power on or enters standby mode. 2. 0-9
Set the channel. TELETEXT mode: Set the page.
3. INPUT Select a TV input source.
4. SLEEP Allows you to set a time when the TV automatically switches to standby. This display will disappear after a few seconds, and the sleep timer automatically starts counting down. If you want to adjust the sleep timer, you can press SLEEP twice then change the time setting. The sleep timer you can select from Off, 10minutes, 20minutes, 30minutes, 40minutes, 50minutes, 60minutes, 90minutes or 120minutes.
5. AV MODE Select an adjusted picture setting. (Standard, Dynamic, Movie, Power Saver, User)
6. FREEZE Set the still image. Press again to return to normal screen.
7. CH▲/▼ Select the channel. (CH▲) Increase the channel number. (CH▼) Decrease the channel number. TELETEXT mode: Select the page. 8. MENU
Display the menu screen. 9. DISPLAY
Display the current channel (or input source) information on the screen. 10. ▲/▼ ◄/► ENTER
Select a desired item on the screen. 11. RETURN Return to the previous menu screen. 12. R G Y B (Red/Green/Yellow/Blue) Select 4 preset favorite channels in 4 different categories. While watching, you can toggle the selected
channels by pressing R, G, Y and B.
16
TELETEXT mode: Select a page. 13.
Only for USB using. Stop Fast rewind Fast forward Pause Play
14. USB Direct switch to USB source.
15. (Mute) Press → Mutes sound. Press again →Restores sound. Mute will be canceled if you press VOL+/-.
16. (Flashback) Press to return to the previous selected channel or external input mode. 17. TV
Direct switch to TV source. 18. PC Direct switch to PC source. 19. VOL+/-
Set the volume. (VOL+) Increase the volume. (VOL-) Decrease the volume.
20. VIEW MODE
Select the Picture Mode. 21. SURROUND
Switch the surround setting. Each time you press SURROUND, the mode changes between On and Off. You can change the surround setting in Audio menu.
22. MPX Select the sound multiplex mode. 23. EXIT
Turn off the menu screen. 24. (TELETEXT)
Select the TELETEXT mode. ( all TV image, all TEXT image, TV/TEXT image) (Reveal hidden for TELETEXT)
TELETEXT mode: Display hidden characters. (SUBTITLE for TELETEXT)
Turn the subtitles on. (Hold)
TELETEXT mode: Stop updating Teletext pages automatically. Press again to release the hold mode.
(Subpage) Display the Teletext subpage directly when in Teletext mode.
(Top/Bottom/Full) TELETEXT mode: Set the area of magnification.
[5] Factory Reset Factory Reset function allows a TV to restore factory settings. Follow below instructions to do Factory Reset.
1. Press MENU + Numeric keys “3481” to enter factory mode, and then the factory mode menu is displayed.
17
2. Press ▲/▼ to select Setup, and then press ► to enter.
3. Press ▲/▼ to select Factory Reset, and then press ► to enter.
4. Press ENTER, then the TV do Factory Reset automatically.
18
CHAPTER 4.TROUBLESHOOTING TABLE [1]TROUBLE SHOOTING TABLE
YES
NO
The sound is not emitted from the speaker though the picture has come out.
No sound output in all modes?
Is the audio signal output of pin (210) (AOSDATA0), pin (208) (AOBCK), pin (211) (AOLRCK) and pin (209) (AOMCLK) of IC U2101 normal?
NO
YES NO
YES
NO
YES
Check IC U2101 and its peripheral circuits.
Is audio signal input to pin (12) (AOSDATA0), pin (16) (AOBCLK), pin (15) (AOLRCK) and pin (4) (AOMCLK) of IC U6103 (AMP) normal?
Check the line between IC U2101 and IC U6103
Is MUTE circuit [PD#] normal? Check the PD#. (Q6103, Q6106, ZD6101, etc.)
Is the audio signal output of pin (3, 4) (L-ch) and pin (1, 2) (R-ch) of CN6101 (AOUDIO-CONNECTOR) normal?
Check IC U6101 and its peripheral circuits.
Check Speaker Box (right and left) and wire harness.
Yes:
19
No sound (during the reception of TV broadcasting)
Does not the sound go out though the picture has come out when UHF/VHF is received?
YES
NO Is the DIF signal output from pin (10) and pin (11) of TUNER
(TU1301) normal?
NO
Check the tuner and its peripheral circuits. Replace as required.
Is the DIF signal sent to pin (184) and pin (185) of IC U2101
normal?
Check IC U2101 its peripheral circuits.
YES
Refer to “No sound output in all modes”.
20
No sound from external input devices (YPbPr)
Does not the sound of the audio signal input to (YPbPr) go out?
YES
NO Is the audio signal properly sent to pin (8) and pin (10) of
CN1203 ?
NO
Check the connection to CN1105 and the external input device.
Is the audio signal properly sent to pin (196) (AIN0_L) and pin (194) (AIN3_R) of IC U2101?
Check the line between CN1105 and IC U6203
YES
Refer to “No sound output in all modes”.
Is the audio signal properly sent to pin (3) (IN2a) and pin (7) (IN2b) of IC U6203?
YES
NO
Check the line between U6203 and IC U2101
21
No sound from external input devices (3)
Does not the sound of the audio signal input to input7 (Composite) go out?
MAIN UNIT:
YE
NO Is the audio signal properly sent to pin (4) and pin (2) of
CN1104?
NO
Check the connection to CN1104 and the external input device.
Check the line between CN1104 and IC U2101.
YES
Refer to “No sound output in all modes”.
No sound from external input devices (VGA)
Does not the sound of the audio signal input to VGA go out?
YES
NO Is the audio signal properly sent to pin (3) and pin (2) of
CN4104?
NO
Check the connection to CN4104 and the external input device.
Check the line between CN4104 and IC U6203.
YES
Is the audio signal properly sent to pin (1) (IN1a) and pin (6) (IN1b) of IC U6203?
Is the audio signal properly sent to pin (196) (AIN0_L) and pin (194) (AIN0_R) of IC U2101?
NO
Check the line between U6203 and IC U2101
22
No sound from external input devices input4 (AV INPUT)
Does not the sound of the audio signal input to (AV input) go out?
YES
NO Is the audio signal properly sent to pin (3) and pin (6) of
CN1201 ?
NO
Check the connection to CN1201 and the external input device.
Is the audio signal properly sent to pin (196) (AIN0_L) and pin (194) (AIN3_R) of IC U2101?
Check the line between CN1201 and IC U6203
YES
Refer to “No sound output in all modes”.
Is the audio signal properly sent to pin (3) (IN2a) and pin (7) (IN2b) of IC U6203?
YES
NO
Check the line between U6203 and IC U2101
23
YES
YES
YES
No sound from external input devices (USB)
Does not the sound of the audio signal input to USB go out?
YES
NO Is USB stick audio format correct? Change to correct mp3 format
Is the USB +5V Q7104 sent to pin (1) of CN1103?
Is the USB con (CN1103) signal properly sent to pin (109)
(USB_DM) and pin (110) (USB DP) of IC U2101?
Refer to “No sound output in all modes”.
NO
NO
Check the connection to Q7104 and the external input device.
Check the line between CN1103 and IC 2101
24
.
YES
The audio signal is not output(headphone)
No audio signal output from Headphone terminal (CN6202).
Is audio signal output properly from pin (12) (OUT_L) and pin
(3) (OUT_R) of IC U6201 to Jack (CN6202)?
Check IC2101 and its peripheral circuits.
Is the audio signal output properly from IC U2101 pin (201)
(AL1O) and pin (203) (AR1O) to pin (13) (INL) and pin (6) (INR)
of IC U6201
Check the connection to CN6202 and external devices.
Check the line between IC U2101 and IC U6202.
YES
No
No
25
YES
YES
The audio signal is not output(AV out)
No audio signal output from AV out terminal (CN1202).
Is audio signal output properly from pin (12) (OUT_L) and pin
(3) (OUT_R) of IC U6201 to Jack (CN1202)?
No
Is the audio signal output properly from IC U2101 pin (200)
(AL0) and pin (202) (AR0) sent to U6201 pin(2) (INR) and
pin(13) (INL)?
No
Check IC U2101 and its peripheral circuits.
Check the connection to CN1202 and external devices.
Check the line between IC U2101 and U6201
26
Main UNIT: Is LVDS signal output IC U2101 in each mode?
(O0N/O0p),(O1N/O1P),(O2N/O2P),(O3N/O3P),(OCKN/OCKP), (E0N/E0p), (E1N/E1P), (E2N/E2P), (E3N/E3P), (ECKN/ECKP)
YES
No picture on the display (1)
The picture doesn't appear in all modes.
Is the above-mentioned LVDS signals output to
connector CN4101 ?
Is LCD controller's control signal normal?
Similarly, is the LVDS signal input to connector of the
panel module?
Check the panel module.
Check IC U2101 and its peripheral control circuits.
Check the line between IC U2101 and CN4101
Control signals Backlight_ON , PSON, and it peels off
and whether normality is checked.
Wire harness is checked.
NO
YESNO
NO
YES
YES
YES
NO
27
Main UNIT:
No picture on the display (TV)
Does not the picture come out when VHF/UHF is received?
Is the voltage of regulation for a TUNER circuit and the power
supply terminal of IC U2101 supplied?
Is the DIF signal output from pin (10) and pin (11) of TUNER
(TU1301)?
Is the DIF signal sent to pin (184) and pin (185) of IC U2101?
Refer to “The picture doesn't appear in all modes.”
Each power supply circuit is checked.
Check the tuner and its peripheral circuits. Replace
as required.
Check IC U2101 its peripheral circuits.
NO
NO
NO
YES
YES
YES
28
<External input Input4>No picture on the display (AV)
Does not the picture of the AV video signal input to Input4(AV)?
Terminal
Is AV signal sent to pin (2) of AV (CN1201) ?
Is AV signal sent to pin (181) of IC U2101?
Main UNIT:
Refer to “The picture doesn't appear in all
modes.”?
Check the setting of an external input device that
connects of CN1201
Check the line between IC U2101 and CN1201.
NO
NOYES
YES
YES
29
Main UNIT:
<External input Input1(Side HDMI1)>No picture on the display
Does not the picture of the HDMI signal input to Input1 (HDMI1)?
Terminal
Is TMDS signal input into pin
(33, 32) RX1_2/ RX1_2B,
(30,29 )RX1_1 /RX1_1B,
(28,27)/RX1_0/RX1_0B
(24, 25)/RX1_C/RX1_CB of IC U1205?
Refer to “The picture doesn't appear in all
modes.”?
Check the line between pin (16) of IC U8103 and
CN8102.
Check the line between IC U8103 and CN8102.
NO
NO
YES
YES
Is the HOT_PLUG detection function of pin (19) of
a HDMI terminal (CN8102) normal?
Check the connection and setup with the
external HDMI devices.
30
<External input Input2 (Rear_HDMI)>No picture on the display
Does not the picture of the HDMI signal input to Input2 (HDMI)?
Terminal
Is TMDS signal input into pin
(12 .11) RX3_2/ RX3_2B,
(10,9 ) RX3_1 / RX3_1B,
(8,7) RX3_0/ RX3_0B
(6, 5) RX3_C/ RX3_CB of IC U1205?
Refer to “The picture doesn't appear in all
modes.”?
Check the line between pin (1) of IC U8103 and
CN8103.
Check the line between IC U8103 and CN8103.
NO
NO
YES
YES
Is the HOT_PLUG detection function of pin (19) of
a HDMI terminal (CN8103) normal?
Check the connection and setup with the
external HDMI devices.
31
<External input USB>No picture on the display
Does not the sound of the video signal input to USB go out?
Is USB stick video format correct?
Is the USB +5V sent to pin (1) of CN1103?
YES
Change to correct . JPG/MP3/MPEG-2 format. NO
NO Check the CN1103 and the external input device.
Is the USB con (CN1103) signal properly sent to
pin (109) (USB_DM) and pin (110) (USB_DP) of IC
U2101?
YES
Refer to “The picture doesn't appear in all modes.”
NO Check the line between CN1103 and IC U2101.
YES
32
<External input Input3(Component)>No picture on the display
Does not the picture of the component video signal input to Component?
Main UNIT:
Is Component Y/Pb/Pr signal sent to pin (2)/Y,
(4)/Pb, (6)/Pr of CN1203 ?
Is Component Y/Pb/Pr signal sent to pin (163)/Y,
(165)/Pb, (166)/Pr of IC U2101?
YES
Check the setting of an external input device that
connects of CN1203
NO
NO Check the line between IC U2101 and CN1203.
Refer to “The picture doesn't appear in all modes.”
YES
Terminal
33
<External input input5>No picture on the display
Does not the picture of the VGA signal input to D-SUB go out?
Is Video format correct? Set the timing which TV is support NO
Terminal Is R/G/B/H/V signal sent to pin (1)/R, (2)/G, (3)/B,
(14)/H, (13)/V of VGA (CN1102)?
Is R/G/B/H/V signal sent to pin (156)/R, (154)/G,
(152)/B, (150)/H, (149)/V of IC U2101?
YESMain UNIT:
YES
Refer to “The picture doesn't appear in all modes.”
Check the setting of an external input device that
connects of CN1102
NO
Check the line between IC U2101 and CN1102. NO
YES
34
35
CHAPTER 5. MAJOR IC INFORMATIONS [1]MAJOR IC INFORMATIONS
1.1. U2101 (MT5301B) GENERAL DESCRI PTION The MediaTek MT5301B family is a backend decoder and a TV controller and offers high integration for advanced applications. It combines a high definition video decoder, an audio decoder, a dual-link LVDS/mini-LVDS transmitter, and an NTSC/PAL/SECAM TV decoder with a 3D comb filter (NTSC/PAL). The MT5301B enables consumer electronics manufactures to build high quality, low cost and feature-rich DTV. World-Leading Audio/Video Technology: The MT5301B supports Full-HD MPEG1/2/4/DiviX/VC1/RM/H.264/AVS video decoder standards, and JPEG. The MT5301B also supports MediaTek MDDiTM de-interlace solution can reach very smooth picture quality for motions. A 3D comb filter added to the TV decoder recovers great details for still pictures. The special color processing technology provides natural, deep colors and true studio quality video.Also, the MT5301B family has built-in high resolution and high-quality audio codec. Rich Features for High Value Products: The MT5301B family enables true single-chip experience. It integrates high-quality HDMI1.3 (partial HDMI1.4), high speed VGA ADC, dualchannel LVDS, USB2.0 receiver, , TCON and panel overdrive. Key Features: 1. Worldwide multi-standard analog TV demodulator 2. A muti-standard video decoder 3. An audio decoder 4. HDMI1.3 receiver (cover HDMI1.4 partial Spec)
HDMI 1.4 Spec.
Ethernet Channel
3D over HDMI
4Kx2K Audio Return Channel
Additional Color Space
Optional Yes No Yes Yes
5. Audio codec 6. TCON 7. Panel overdrive control 8. Local dimming GENERAL FEATURE LIST Host CPU
ARM1176JZS
14K Boot ROM
36
JTAG ICE interface
Watch Dog timers
Transport Demultiplexer Support DES / 3-DES / DVB / AES / de-scramblers
Up to 8 even/odd keys for descrambling
Supports 32 PID filters and 32 section filters
Supports 32 PID filters for recording
Supports hardware CRC-32 check
Supports PCR recovery function
Supports a micro-processor for stream process and video start code detection
MPEG2 Decoder MPEG MP@ML, MP@HL
Supports de-blocking filter
MPEG1 Decoder MPEG4 Decoder
ASP@L5
H.264 (MPEG4.10) HD Decoder (AVC) [email protected], [email protected], constrained BP@L3 video standard
VC-1 (SMPTE421M) MP@HL, AP@L3(Partial Support, support up to 1920x1080)
WMV9 decoder MP@HL
DivX (XviD) Decoder DIVX3 / DIVX4 / DIVX5 / DIVX6 / DIVX HD
AVS Decoder Jizhun profile @Level 6.0.1
RMVB Decoder RealVideo8/9/10
Soreson H.263 Still Image decoding
JPEG (base-line or progressive)
De-mosquito engine 2D/3D for all AV inputs
2D Graphics Supports multiple color modes
Point, horizontal/vertical line primitive drawings
Rectangle fill and gradient fill functions
Bitblt with transparent options
Alpha blending and optional pre-multiplied alpha composition Bitblt
37
Stretch Bitblt
YCbCr to RGB color space conversion
Support index to direct mode bitblt
Image Resizer Supports 16bpp/32bpp direct color format.
Supports 420/422 video format.
Supports 420/422/444 JPEG format.
Arbitrary ratio vertical/horizontal scaling of video, from 1/128X to 128X
Simple DMA.
OSD Plane Three linking list OSDs with multiple color mode and two of them has up-scaler
Video Plane Supports video freeze and over scan.
Flesh tone management
Gamma correction
Color Transient Improvement (CTI)
2D Peaking
Saturation/hue adjustment
Brightness and contrast adjustment
Black and White level extender
Adaptive Luma management
Automatic detect video, film and mixed-mode source
3:2/2:2 pull down source detection
Supports FHD motion-adaptive de-interlace in 32bit dram interface
Supports excellent low angle image processing
Brilliant boundary shaping for moving object
Advanced non-linear panorama scaling.
Programmable zoom viewer
Progressive scan output
Supports alpha blending for OSD on video plane.
Dithering processing for flat panel display
Frame rate conversion.
Supports FHD panel and VGA dot-to-dot
Supports PIP/POP, (dual de-interlace, one HD and one SD)
OD Support 60Hz Full-HD and WXGA panel over drive.
TCON
Flexible timing control with programmable timing
38
i. Horizontal timing control
ii. Vertical timing control
iii. Multi-line timing control
iv. Multi-frame timing control
Support gate power modulation timing
Support 1/2/4/8 frame inversion, 1-line inversion, 2-line inversion, and could up to 255-line dot inversion
Local Dimming Block division: up to 800 total blocks, up to 100 horizontal blocks
Support 50K ~ 50M SPI clock rate
LVDS Support 6/8/10/12-bit one-link, or 6/8/10-bit dual-link LVDS transmitter,
Built-in spread spectrum for EMI performance
Programmable panel timing output
Mini-LVDS Single port 6/8-bit 6 pairs mini-LVDS output for WXGA 60Hz panel
Single port 6/8-bit 3 pairs mini-LVDS output for WXGA 60Hz panel
Dual port 6/8-bit 3 pairs mini-LVDS output for WXGA 60Hz panel
Single port 8bit 6 pairs mini-LVDS output for FHD 60Hz panel
Dual port 8 bit 6 pair mini-LVDS output for FHD 60Hz panel
Dual port 8bit 3 pairs mini-LVDS output for FHD 60Hz panel
CVBS In On-chip 54 MHz 10-bit video ADC
Supports PAL (B,G,D,H,M,N,I,Nc), NTSC, NTSC-4.43, SECAM
NTSC/PAL supports 3D/2D comb filter
Built-in motion-adaptive 3D Noise Reduction
VBI data slicer for CC/TT decoding
Supports 2 S-Video.
MT5301B support 2-channel CVBS.
Supports SCART connector
VGA In Supports VGA input up to UXGA 162 MHz
Supports full VESA standards
Component Video In Supports two component video inputs
Supports 480i / 480p / 576i / 576p / 720p / 1080i / 1080p
Audio ADC MT5301B support 1-pair L/R input
Audio digital input
39
MT5301B support 2 bit (4 channel) I2S audio input (muxed with GPIO).
HDMI Receiver One channel HDMI1.4
v. Maximum data rate can be up to 3.3 GHz
vi. Support 3D video format
vii. Audio Return channel
EIA/CEA-861B
CEC
Video bypass TV bypass
CVBS Monitor (any AV input)
TV audio demodulator Supports BTSC / EIA-J / A2 / NICAM / PAL FM / SECAM world-wide formats
Standard automatic detection
Stereo demodulation, SAP demodulation
Mode selection (Main/SAP/Stereo)
Audio DAC MT5301B support 2-pair audio DACs
DRAM Controller 16bit DDR2/DDR3 interface,
MT5301B Support DDR2 1026 MHz, DDR3 1188MHz.
Supports 512Mb or 1 Gb DDR2 DRAM device and 1Gb or 2Gb DDR3 device. MT5301B has 16-bit data
bus offers
up to 256MB space (one x16 DRAM device).
Supports DDR2-800/DDR2-1066/DDR3-1333/DDR3-1600 device
Audio DSP MPEG-1 layer I/II decoding
Support WMA / HE-AAC
Audio output: 5.1ch + 2ch (down mix) + 2ch(bypass)
Pink noise and white noise generator
Equalizer
Bass management
3D surround processing with virtual surround
Audio and video lip synchronization
Supports bass/treble
Automatic volume control
MT5301B support 2-bit (4-channel) main audio I2S output interface: each of these channels is up to 24-bit
resolution.
40
S/PDIF interface Support SPDIF in bypass
One SPDIF out
Analog TV IF Demodulator Supports world-wide analog TV standard
Accept Low IF frequency
Full digital AGC control and carrier recovery
Embedded SAW filter and IF Amplifier. Cost effective TV front-end structure and no more costs on
viii. External analog SAW filters (Video/Audio)
ix. External analog IF demodulator
x. Extra peripheral circuit on CVBS signal data path
xi. External SAW filter and IF VGA on tuner
Peripherals MT5301B support two built-in UARTs with Tx and Rx FIFO.(one is muxed with GPIO).
Seven basic serial interfaces; one is for the tuner, one is the master for general purpose, and one is the
slave for
VGA DDC, the other four extra slave serial interfaces used for HDMI EDID data (three are muxed with GPIO).
MT5301B support two PWMs (one is muxed with GPIO).
IR receiver
Real-time clock and watchdog controller
Built-in 2-link USB2.0/1.1, USB port0 supports external hub,
Built-in uP for standby mode
Support SDIO interface pin muxed
Supports two serial flash or one serial
MT5301B support five-input low-speed ADC.
Supports boundary scan (JTAG)
IC Outline MT5301B is 256-pin LQFP package with EPAD
3.3V/1.12V/1.2V and 1.8V for DDR2 or 1.5V for DDR3
1.2. U3103 (W971GG6JB-25 1G WBGA-84) Description The W971GG6JB is a 1G bits DDR2 SDRAM, organized as 8,388,608 words 8 banks 16 bits.
This
device achieves high speed transfer rates up to 1066Mb/sec/pin (DDR2-1066) for general
applications. W971GG6JB is sorted into the following speed grades: -18, -25 and -3. The -18 is
compliant to the DDR2-1066/CL7 specification, the -25 is compliant to the DDR2-800/CL6
specification, the -3 is compliant to the DDR2-667/CL5 specification.
41
All of the control and address inputs are synchronized with a pair of externally supplied differential
clocks. Inputs are latched at the cross point of differential clocks (CLK rising and CLK falling). All
I/Os are synchronized with a single ended DQS or differential DQS- DQS pair in a source
synchronous fashion.
Features _ Power Supply: VDD, VDDQ = 1.8 V
± 0.1 V
_ Double Data Rate architecture: two data transfers per clock cycle
_ CAS Latency: 3, 4, 5, 6 and 7
_ Burst Length: 4 and 8
_ Bi-directional, differential data strobes (DQS andDQS ) are transmitted / received with data
_ Edge-aligned with Read data and center-aligned with Write data
_ DLL aligns DQ and DQS transitions with clock
_ Differential clock inputs (CLK and CLK )
_ Data masks (DM) for write data
_ Commands entered on each positive CLK edge, data and data mask are referenced to both
edges of DQS
_ Posted CAS programmable additive latency supported to make command and data bus efficiency
_ Read Latency = Additive Latency plus CAS Latency (RL = AL + CL)
_ Off-Chip-Driver impedance adjustment (OCD) and On-Die-Termination (ODT) for better signal
quality
_ Auto-precharge operation for read and write bursts
_ Auto Refresh and Self Refresh modes
_ Precharged Power Down and Active Power Down
_ Write Data Mask
_ Write Latency = Read Latency - 1 (WL = RL - 1)
_ Interface: SSTL_18
_ Packaged in WBGA 84 Ball (8X12.5 mm2), using Lead free materials with RoHS compliant
1.3. U6101 (AD82581-LE48NAY LQFP48) Description AD82581 is a digital audio amplifier capable of driving a pair of 8Ω,10W or a single 4Ω,20W
speaker, both which operate at a 24V supply without external heat-sink or fan requirement.
Using I2C digital control interface, the user can control AD82581’s input format selection, mute
and volume control functions. AD82581 has many built-in protection circuits to safeguard AD82581
from connection errors.
Features 16/18/20/24-bit input with I2S, Left-alignment
and Right-alignment data format
42
PSNR & DR (A-weighting)
Loudspeaker: 97dB (PSNR), 105dB (DR) @24V
Multiple sampling frequencies (Fs)
32kHz / 44.1kHz / 48kHz and
64kHz / 88.2kHz / 96kHz and
128kHz/176.4kHz/192kHz
System clock = 64x, 128x, 256x, 384x, 512x, 768x,
1024x Fs
256x~1024x Fs for 32kHz / 44.1kHz / 48kHz
128x~512x Fs for 64kHz / 88.2kHz / 96kHz
64x~256x Fs for 128kHz/176.4kHz/192kHz
Supply voltage
3.3V for digital circuit
12V~24V for loudspeaker driver
Loudspeaker output power for 24V
10W x 2CH into 8Ω @0.27% THD+N for stereo
12W x 2CH into 8Ω @0.3% THD+N for stereo
15W x 1CH into 4Ω @0.2% THD+N for mono
20W x 1CH into 4Ω @0.25% THD+N for mono
Anti-pop design
Over-temperature protection
Internal PLL
Under-voltage shutdown
Over-current protection
Applications · CD and DVD · TV audio · Car audio · Boom-box · MP3 docking systems · Powered speaker · Wireless audio · USB speaker 1.4. U8103(IT6633) Features
The IT6633 is a three-to-one HDMI v.1.3 active switch that supports a signalling rate of up to 2.25Gbps and the new Deep Color modes. A one-port SINK systems such as flat-panel TVs or LCD projectors could also easily upgrade to three-port by
43
adding an IT6633 at the front. The IT6633 operates in software mode that allows the system to control it via a two-line serial interface, PCSCL/PCSDA. The IT6633 offers two selectable serial programming addresses by PCADR0.
As a active switch, the IT6633 equalizes incoming TMDS data with optimal quality regardless of the incoming signal quality. The highly acclaimed equalization technology of ITE TECH. INC. provides for support of long or low-quality HDMI cables at even the highest speeds. Input terminations of theTMDS inputs and output current levels are both programmable. In addition, the input terminations are disconnectable and hence significantly lower the system power consumption in inactive modes.
The IT6633 embeds an EDID RAM to save the cost of the Three external EDID ROMs. The process of downloading the EDID data into the RAM is simplified by the automatic read-back capability of the
IT6633, minimizing the need of MCU intervention. The IT6633 also embeds three 1K-ohm resisters for HPD signal paths to save external resisters and easy to implement the plug authentication.
The IT6633 also incorporates I2C repeater in its DDC switches, which isolates the DDC capacitances of the two sides of the switch. This allows for longer cable cascading as well as significantly eases the system design to pass Test ID 8-9: DDC/CEC Line Capacitance and Voltage of the HDMI Compliance Test.
The IT6633 also distinguish itself from its peers in that it offers 8kV of Human Body Mode ESD protection to all TMDS high-speed input pins. This saves significant costs in external high-speed ESD diodes, which could be very expensive . Features HDMI active switch, providing superior performance over traditional passive
switches Compliant with HDMI 1.3 and DVI 1.0 standards Serial data rate at up to 2.25Gbps, capable of supporting the following digital
video formats in Deep Color Mode at up to 36 bits (12 bits/color): DTV resolutions: 480i, 576i, 480p, 576p, 720p, 1080i to 1080p PC resolutions: VGA, SVGA, XGA, SXGA to UXGA
Single 3.3V operation Internal AC-coupling at TMDS inputs to cope with uneven intra-pair DC levels of
incoming TMDS signals. Embedded EDID RAM saves external EDID ROM costs Embedded HDP resistors Integrated HPD switches Active port detection by monitoring PWR5V inputs and TMDS input clock. DDC I2C repeater isolates backend DDC capacitive loading from frontend,
44
enhancing the DDC operation compatibility Human Body Mode ESD protection up to 8kV for all TMDS differential input pins Disconnectable input terminations with auto-calibrated impedances Adaptive input equalization supporting long and short cables at the same time Software-mode operation providing flexibility Two possible serial programming device address.. Programmable TMDS output current level Programmable source terminations compliant with HDMI 1.3 standard, providing
optimal source data eyes at high speeds High-impedance TMDS output when disabled Optional backend receiver termination detection for auto powerdown 64-Pin LQFP package RoHS Compliant ( 100% Green available ) 1.5. U6202 (DRV632) DESCRIPTION
The DRV632 is a 2-VRMS pop-free stereo line driver designed to allow the removal of the output
dc-blocking capacitors for reduced component count and cost. The device is ideal for single-supply
electronics where size and cost are critical design parameters
Designed using TI’s patented DirectPath™ technology, The DRV632 is capable of driving 2
VRMS into a 10-kΩ load with 3.3-V supply voltage. The device has differential inputs and uses
external gain-setting resistors to support a gain range of ±1 V/V to ±10 V/V, and gain can be
configured individually for each channel. Line outputs have ±8-kV IEC ESD protection, requiring
just a simple resistor-capacitor ESD protection circuit.The DRV632 has built-in active-mute control
for pop-free audio on/off control.The DRV632 has an external undervoltage detector that mutes the
output when the power supply is removed, ensuring a pop-free shutdown.
Using the DRV632 in audio products can reduce component count considerably compared to
traditional methods of generating a 2-VRMS output. The DRV632 does not require a power supply
greater than 3.3 V to generate its 5.6-Vpp output, nor does it require a split-rail power supply. The
DRV632 integrates its own charge pump to generate a negative supply rail that provides a clean,
pop-free ground-biased 2-VRMS output.
The DRV632 is available in a 14-pin TSSOP.
FEATURES DESCRIPTION 23• Stereo DirectPath™ Audio Line Driver– 2 Vrms Into 10 kΩ With 3.3-V Supply• Low THD+N
< 0.01% at 2 Vrms Into 10 kΩ• High SNR, >90 dB• 600-Ω Output Load Compliant
• Adjustable Gain by External Gain-Setting Resistors• Low DC Offset, <1 mV•
Ground-Referenced Outputs Eliminate
DC-Blocking Capacitors
45
– Reduce Board Area
– Reduce Component Cost
– Improve THD+N Performance a– No Degradation of Low-Frequency Response Due to
Output Capacitors• Short-Circuit Protection
• Click- and Pop-Reduction Circuitry
• External Undervoltage Mute
• Active Mute Control for Pop-Free Audio On/Off Control• Space-Saving TSSOP Package
APPLICATIONS• Set-Top Boxes • Blu-ray Disc™, DVD Players
• LCD and PDP TV
• Mini/Micro Combo Systems
• Sound Cards
• Laptops
46
CHAPTER 6.BLOCK DIAGRAM/WIRING DIAGRAM [1]BLOCK DIAGRAM(21.5”)
[2]POWER MANAGEMENT BLOCK DIAGRAM There are 1 part circuits in Power board of this project (fig.1), Power circuits which is a single layer board, There are 3 output in the power parts, one is interface board including USB and TV tuner et; the other is inverter board and audio circuit.+24V output is inverter & audio part.the system block diagram as below; the last is panel Vcc, the power is 12V.
47
LC-22LE420M
[3]WIRING DIAGRAM (LC-22LE420M)
48
49
CHAPTER 7.PRINTED WIRING DIAGRAM [1]MAIN UNIT PRINTED WIRING BOARD (LC-22LE420M)
TOP
50
BOTTOM
51
[2]POWER SCHEMATIC DIAGRAM- POWER BOARD WITH TOP/BOTTOM VIEW TOP Layer(LC-22LE420M)
52
Bottom Layer (LC-22LE420M)
[3]KEY UNIT PRINTED WIRING BOARD(LC-22LE420M)
[4] IR UNIT PRINTED WIRING BOARD (LC-22LE420M)
53
CHAPTER 8.SCHEMATIC DIAGRAM [1]MAIN SCHEMATIC DIAGRAM (LC-22LE420M)
01 MAIN POWER
54
02 MT5301B
55
03 Peripheral/ Flash.
56
04 DDR SDRAM
57
05 LVDS
58
06 AUDIO AMP
59
07 HP/ Lineout/ Audio SW
60
08 HDMI Interface
61
09 VGA/ USB/ RS232
62
10 YCbCr/ CVBS/ SPDIF
63
11 TUNER
[2]POWER SCHEMATIC DIAGRAM
POWER SCHEMATIC DIAGRAM FOR(LC-22LE420M)
1. 1) AC Input and EMI Filter:(fig.3)
(fig.3)
64
CN801 is a connector for connecting AC Power. F850&F851 is fuse to protect all the circuit AC. Input voltage is from 90V to 264V. CY801, CY802, CY803 are used high frequency noise of primary between common GND. one inputting main circuit to prevent man from shock. L801, C851, is used to filter low frequency noise. R850, R851 are used to discharge .
2) MAIN POWER Control Circuit:(fig.4)
65
fig.4 U830 is a current-mode PWM controller with excellent power-saving operation, It features a high-voltage current source to directly supply the startup current from bulk capacitor and further to provide lossless startup circuit. Max start-up current for U830 is 100uA, When current flow from the
bulk capacitorC853/C854 through R832 and R833 gets to HV pin to start up U830, Meanwhile, the VCC supply current is as low as 1mA thus most of the HV current is utilized to change the VCC capacitor C856, the Vcc supply current is provided from the auxiliary winding of the transformer PIN4.
INN801 detects the MOSFET current, from the CS in.When CS pin over 0.7V, theU830 will enter auto-recovery type protection, Presenting a hiccup mode. The gate-out will not resume switching until OCP falls below 0.85V.
U830 control 5V&16V output ,D856,C862,C8663,L855 are used to 5V rectifier and smooth ,for system standby function circuit .D861,C864,C863 are sued rectifier to U930 Vcc input Pin, and 16Voutput through U930 rectifier to interface board.
9. EXPLODED PARTS
No. PARTS CODE DESCRIPTION EXPLODED PARTS
1 9KD102222530H LCP21.5"M215HGE-L10,ML5HE10901(A)(CMO)HF
2 9KD03G224G01R ASSY FRONT BEZEL,VG224G
3 9KD05G224G01R ASSY BACK COVER FOR ASEAN,VG224G
4 9KD04T264C01R ASSY KEY,VT264C
5 9KD02T264C01R ASSY BASE,VT264C
6 9KD05G224G05R ASSY IF SHIELDING FOR ASEAN,VG224G
7 9KD1X1500500R PCBA,KP/BD,VG264C-52SP RoHS
LC-22LE420M
8 9KD0T1600500R PCBA,IR/BD,VG264C-52SP,ROHS
9 9KD471200500R PCBA,IF/BD,VG224G-51SP,ROHS
10 9KDAC1400500R PCBA,PI/BD,VG224G-51SP,ROHS
11 9KD20T464D02R AC COVER ,VT464D
12 9KD151040100R Remote controller RC-QSHAR-520
9KD0709000B0RPWRCORD 2.5A/250V BLK 1.6/0.08M CEE
(India/ Indonesia/ Central Asia/ Malaysia)
9KD0709000A0RPWRCORD 2.5A/250V BLK 1.6/0.2M ASTA 2P TO
(Singapore/Middle East)
9KD070900090RPWRCORD 2.5A/250V BLK 1.6/0.2M CCC 2P TO
(Philippines)
14 9KD100300019R SPEAKER 3W16Ω 395/415mm R/B/W W/CASE
13
15 9KD3006009V0R HRN ASSY 6P 135MM UL1061#30
16 9KD3030046A0R HRN ASSY LVDS 2X15P TO 30P 95mm W/LOCK
17 9KD301400820R HRN ASSY 2X7P TO 6P/4P 440/520mm
18 9KD08T264C02R TOP VESA HOLDER,VT264C
19 9KD02T264C04R BASE SUPPORT,VT264C
20 9KD000001000R BOLT,#4-40x12.5,Ni ROHS
21 9KD05G224G02R ASSY MAIN CHASSIS ASEAN-L10,VG224G
22 9KD476640900R SCREW,B,CROSS,W/W-SPR,M4*42,Zn,ROHS
23 9KD10T421J01R WIRE CLIP,CH-01S-V0,VT421J
24 9KD10T321H02R WIRE CLIP,CHR-05-V0,VT321H
25 9KD799001010R ADAPTER RF JACK/ PAL PLUG (Philippines)
26 9KD416606901R SCREW,B,CROSS,M4*6,Zn-black
27 9KD146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc
28 9KD112322100R SCREW,P,CROSS,T.T-M3*4.5,Zn,ROHS
29 9KD018303900R SCREW,I,CROSS,M3*3,Zn-BLK,ROHS
30 9KD112310500R SCREW,P,CROSS,T.T-3*10,BLK-Zn
31 9KD016306900R SCREW,I,CROSS,Φ5.5,T3*6,BLK-Zn
32 9KD412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS
33 9KD212612120R SCREW,B,CROSS,T.T-4*12,BLK ROHS
34 9KD146304200R SCREW,P,CROSS,W/WAS,M3*4,Zn-Cc,ROHS
9. PARTS GUIDE
No. PARTS CODEPRICE
RANK
NEW
MARK
Part
Delivery DESCRIPTION
1 9KD102222530H CB N * LCP21.5"M215HGE-L10,ML5HE10901(A)(CMO)HF
2 9KD03G224G01R AY N * ASSY FRONT BEZEL,VG224G.
3 9KD05G224G01R BC N * ASSY BACK COVER FOR ASEAN,VG224G.
4 9KD04T264C01R AN N * ASSY KEY,VT264C.
5 9KD02T264C01R BA N * ASSY BASE,VT264C.
6 9KD05G224G05R AP N * ASSY IF SHIELDING FOR ASEAN,VG224G.
7 9KD1X1500500R AP N * PCBA,KP/BD,VG264C-52SP RoHS.
8 9KD0T1600500R AK N * PCBA,IR/BD,VG264C-52SP,ROHS.
9 9KD471200500R BR N * PCBA,IF/BD,VG224G-51SP,ROHS.
10 9KDAC1400500R BF N * PCBA,PI/BD,VG224G-51SP,ROHS.
11 9KD20T464D02R AG N * AC COVER ,VT464D.
12 9KD151040100R AT N * Remote controller RC-QSHAR-520
9KD0709000B0R AR N * PWRCORD 2.5A/250V BLK 1.6/0.08M CEE (India/ Indonesia/ Central Asia/ Malaysia)
9KD0709000A0R AT N * PWRCORD 2.5A/250V BLK 1.6/0.2M ASTA 2P TO (Singapore/Middle East)
9KD070900090R AR N * PWRCORD 2.5A/250V BLK 1.6/0.2M CCC 2P TO (Philippines)
14 9KD100300019R AZ N * SPEAKER 3W16Ω 395/415mm R/B/W W/CASE.
15 9KD3006009V0R AL N * HRN ASSY 6P 135MM UL1061#30
16 9KD3030046A0R AT N * HRN ASSY LVDS 2X15P TO 30P 95mm W/LOCK
17 9KD301400820R AR N * HRN ASSY 2X7P TO 6P/4P 440/520mm
18 9KD08T264C02R AR N * TOP VESA HOLDER,VT264C.
19 9KD02T264C04R AM N * BASE SUPPORT,VT264C.
20 9KD000001000R AE N * BOLT,#4-40x12.5,Ni ROHS.
21 9KD05G224G02R BA N * ASSY MAIN CHASSIS ASEAN-L10,VG224G.
22 9KD476640900R AE N * SCREW,B,CROSS,W/W-SPR,M4*42,Zn,ROHS.
23 9KD10T421J01R AF N * WIRE CLIP,CH-01S-V0,VT421J.
24 9KD10T321H02R AF N * WIRE CLIP,CHR-05-V0,VT321H
25 9KD799001010R AN N * ADAPTER RF JACK/ PAL PLUG (Philippines)
26 9KD416606901R AC N * SCREW,B,CROSS,M4*6,Zn-black
27 9KD146306200R AB N * SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc
28 9KD112322100R AB N * SCREW,P,CROSS,T.T-M3*4.5,Zn,ROHS
29 9KD018303900R AB N * SCREW,I,CROSS,M3*3,Zn-BLK,ROHS
30 9KD112310500R AE N * SCREW,P,CROSS,T.T-3*10,BLK-Zn
31 9KD016306900R AC N * SCREW,I,CROSS,Φ5.5,T3*6,BLK-Zn
32 9KD412608500R AD N * SCREW,B,CROSS,T.T-4*8,BLK ROHS
33 9KD212612120R AD N * SCREW,B,CROSS,T.T-4*12,BLK ROHS
34 9KD146304200R AC N * SCREW,P,CROSS,W/WAS,M3*4,Zn-Cc,ROHS
LC-22LE420M
13