1 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

ENGINE

Manufacturer IAME s.p.a. Category

Make PARILLA HomologationPeriod

Model, Type Leopard X30 125ccRL - TaG - AUS

Pages 22

This homologation sheet reproduces description, illustrations and dimensions of the engine at the time ofthe AKA Homologation. All motors must be manufactured within these dimensions

ENGINE PHOTO - DRIVE SIDE ENGINE PHOTO - OPPOSITE SIDE

SIGNATURE AND STAMPOF APPLICANT

SIGNATURE AND STAMPOF AKA

2 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

PHOTO OFTHE ENGINE FROM THE BACK

PHOTO OFTHE ENGINE FROM THE FRONT

PHOTO OFTHE ENGINE FROM ABOVE

PHOTO OFTHE ENGINE FROM BELOW

3 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

TECHNICAL INFORMATION

A - Characteristics C - Materials

Cylinder volume 123.67 cm³ Cylinder wall Iron

Bore 54 mm Cylinder Aluminium

Theoretical max. bore 54.28 mm Cylinder head Aluminium

Stroke 54 mm Crankcase / sump Aluminium

Cooling system Water Connecting rod Steel

Air admission system Reed valve

No of carburationsystems 1 D - Tolerances

No of transfer ports inthe cylinder 3 Opening angles

(+/- 2 degrees)

No of exhaust ports 3 Combustion chambervolume [+/- 0.5cc]

Shape of combustionchamber Spherical Angles

[+/- 2 degrees]

Volume of thecombustion chamber

10.2 cm³±0.5 (WITH “CIK”INSERT)

Stroke[+/- 0.1mm]

Length between of theaxis of connecting rod 102 mm

Length between axis ofconnecting rod[+/-0.1mm]

Ignition make Selettra or PVL Dimensions onmachined surfaces

Ignition model Digital (REV. LIMIT 16000RPM)

< 25mm [+/- 0.5mm]

25-60mm [+/- 0.8mm]

B – Opening angles > 60mm [+/- 1.5mm]

Inlet Dimensions on roughcast surface

Transfer 126°± 2° TT=127°± 2° < 25mm [+/- 1mm]

Exhaust 177.5° max 25-60mm [+/- 1.5mm]

Inlet opens before TDC > 60mm [+/- 3mm]

4 AKA Homologation No.

Inlet closes before LDC

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

TECHNICAL INFORMATION

E – piston EXHAUST AND INLET TIMING READINGLINES

No of piston rings 1 NOTE : Indicate in the diagram the type of ring onthe piston

Min. weight with ring= 128 g

Overall length 62.8 mm ±0.2

Radius of crown 61.5 mm

Crown to pin 33.8 mm ±0.2

Skirt to pin 29 mm ±0.2

F – Piston Pin

material Steel

Length 44 mm ±0.2

Inside diameter Ø9 mm

Outside diameter Ø14 mm

CARBURETOR LOCATION

G - Gaskets NOTE : Distance from the cylinder centre mayinclude an eventual spacer located before thecarburettorBarrel gasket material Paper

Minimum thickness 0.30 mm

Maximum thickness 0.45 mm

Cylinder head gasketmaterial

Minimum thickness

Maximum thickness

+0.250

5 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

DRAWING OF CYLINDER DEVELOPMENT

DRAWING OFTHE BASE OF THE CYLINDER

DRAWING OFCYLINDER SECTION

CHORDAL READING

ANGULAR READING BY INSERTING A 0.2 mm GAUGE

6 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

DRAWING OF THE COMBUSTION CHAMBER AND CYLINDERHEAD

DRAWING OFTHE CRANKSHAFT

DRAWING OFTHE INTERIOR OF THE SUMP

COMBUSTION CHAMBER VOLUME = 10.2 cm³ ±0.5(WITH “ICC” INSERT: 8.2 + 2 cm³)

“ICC”

ATT.: SQUISH MIN. = 0.90 mm

7 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

PHOTO OFTHE BASE OF THE CYLINDER

PHOTO OFTHE COMBUSTION CHAMBER

PHOTO OF CRANKCASE– GASKET FACE

PHOTO OF CRANKCASE– INTERIOR (HORIZONTAL VIEW)

8 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

VENTURI CARB. DIMENSIONS INLET SILENCER

DRAWING OF EXHAUST SILENCER AND COMPONENTS

Min. weight 1.39 Kg

9 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

CLUTCH DESCRIPTION AND SKETCH OF PARTS

1D

rum

nut

5Sc

rew

9C

lutc

hbo

dy2

Exte

rnal

was

her

6C

lutc

hdr

um10

Sta

rterr

ing

3R

olle

rcag

e7

Inte

rnal

was

her

11S

crew

4Sp

rock

et8

Lock

ing

nut

Z10

/Z11

/Z12

/Z13

(INAL

TER

NA

TIVE

)

Min

.wei

ght=

225

g

Min

.wei

ght=

360

g

Min

.wei

ght=

650

g

Min

.wei

ght=

300

g

10 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

RADIATOR DESCRIPTION AND SKETCH OF PARTS

11 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

INLET PORT CHORD WIDTH

Either A1 or A2The maximum chord width is

Formula for A1 = D x x 0.223 + B

The maximum chord width is

Formula for A2 = D x x 0.223

EXHAUST PORT CHORD WIDTH

Either C1 or C2

Formula for C1 = D x x 0.223 + E Formula for C2 = D x x 0.223

12 AKA Homologation No.

Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classesmust be applied for after Homologation and Registration approvals

GEARBOX

Manufacturer

Make

Model , Type

Primary coupling

Primary shaft Secondary shaft Degree readingobtained after 3turns of the engine

1st gear

2nd gear

3rd gear

4th gear

5th gear

6th gear

13 AKA Homologation No.

WIRING DIAGRAM ( SELETTRA DIGITAL ‘’K’’ IGNITION )

1-E

lect

roni

cC

ontro

lUni

t2-

Sta

rting

rela

y3-

Sta

rter

key

4-Fu

seho

lder

5-B

atte

ry6-

Igni

tion

7-S

tarte

r8-

H.T

.coi

l

14 AKA Homologation No.

ELECTRONIC BOX MARKING

“AKA 20L” MARKING

15 AKA Homologation No.

WIRING DIAGRAM ( PVL DIGITAL IGNITION )

1-E

lect

roni

cC

ontro

lUni

t2-

Sta

rting

rela

y3-

Sta

rter

key

4-Fu

seho

lder

5-B

atte

ry6-

Igni

tion

7-S

tarte

r8-

H.T

.coi

l

16 AKA Homologation No.

GEARS TIMING COMMAND BALANCING SHAFT

BALANCING SHAFT GEAR COMMAND BAL. SHAFT

Min. weight 315 grMin. weight 315

Min. weight 135 gr

1 AKA Homologation No.

PHOTO IDENTIFICATION PISTON

PHOTO IDENTIFICATION CONROD PHOTO IDENTIFICATION BALANCINGSHAFT

VARIABLE

2 AKA Homologation No.

PHOTO IDENTIFICATION CRANKSHAFT

PHOTO IDENTIFICATION GEARCOMMAND BALANCING SHAFT

PHOTO IDENTIFICATION STARTERRING

VARIABLE

VARIABLE

VARIABLE

VARIABLE

3 AKA Homologation No.

PHOTO IDENTIFICATION SPROCKETPHOTO IDENTIFICATION CLUTCH

DRUM

PHOTO IDENTIFICATION CLUTCHBODY PHOTO IDENTIFICATION STARTER

VARIABLEVARIABLE

4 AKA Homologation No.

PHOTO IDENTIFICATION REED GROUP & PETALS

PHOTO IDENTIFICATIONCARBURETOR INLET CONVEYOR

PHOTO IDENTIFICATIONCARBURETOR

5 AKA Homologation No.

PHOTO IDENTIFICATION EXHAUSTSILENCER

PHOTO IDENTIFICATION HEADEREXHAUST

>

PHOTO IDENTIFICATION RADIATOR PHOTO IDENTIFICATION STATOR

6 AKA Homologation No.

PHOTO IDENTIFICATION CLUTCH COVER AND H.T. COIL>

PHOTO IDENTIFICATION BENDIX COVER

16/02/09 n° 2931

CARBURETTOR / CARBURATEUR

TRYTON HOBBY 27-C / 2009

PHOTO OF INLET SIDEPHOTO CÔTÉ ASPIRATION

PHOTO OF ADJUSTING SIDEPHOTO CÔTÉ RÉGLADE

ManufacturerConstructeur VA.MEC SRL

MakeMarque TRYTON

ModelModèle HOBBY 27-C

X30 125cc RL - TaG

16/02/09 n° 2932

SECTION VIEW / VUE EN SECTION

CARBURETTOR DESCRIPTION AND SKETCH OF PARTSDESCRIPTION DU CARBURATEUR ET ESQUISSE DES PIÈCES