Upload
vitor-dias-do-vale
View
224
Download
1
Embed Size (px)
Citation preview
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
1/22
Module2
Analysis of StaticallyIndeterminate Structures
by the Matrix Force
MethodVersion 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
2/22
Lesson
11The Force Method of
Analysis: Frames
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
3/22
Instructional Objectives
After reading this chapter the student will be able to
1. Analyse the statically indeterminate plane frame by force method.2. Analyse the statically indeterminate plane frames undergoing support settlements.3. Calculate the static deflections of a primary structure (released frame) underexternal loads.4. Write compatibility equations of displacements for the plane deformations.5. Compute reaction components of the indeterminate frame.6. Draw shear force and bending moment diagrams for the frame.7. Draw qualitative elastic curve of the frame.
11.1 Introduction
The force method of analysis can readily be employed to analyze the indeterminateframes. The basic steps in the analysis of indeterminate frame by force method arethe same as that discussed in the analysis of indeterminate beams in the previouslessons. Under the action of external loads, the frames undergo axial and bendingdeformations. Since the axial rigidity of the members is much higher than thebending rigidity, the axial deformations are much smaller than the bendingdeformations and are normally not considered in the analysis. The compatibilityequations for the frame are written with respect to bending deformations only. Thefollowing examples illustrate the force method of analysis as applied to indeterminateframes.
Example 11.1
Analyse the rigid frame shown in Fig.11.1a and draw the bending moment diagram.Youngs modulus E and moment of inertia I are constant for the plane frame.Neglect axial deformations.
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
4/22
The given one- storey frame is statically indeterminate to degree one. In the presentcase, the primary structure is one that is hinged at A and roller supported at .
Treat horizontal reaction at , as the redundant. The primary structure (which is
stable and determinate) is shown in Fig.11.1.b.The compatibility condition of theproblem is that the horizontal deformation of the primary structure (Fig.11.1.b) due to
external loads plus the horizontal deformation of the support , due to redundant
D
D DxR
D
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
5/22
DxR (vide Fig.11.1.b) must vanish. Calculate deformation due to unit load at
in the direction of . Multiplying this deformation with , the deformation due
to redundant reaction can be obtained.
11a D
DxR 11a DxR
DxRa11= (1)
Now compute the horizontal deflection L at due to externally applied load. This
can be readily determined by unit load method. Apply a unit load along as
shown in Fig.10.1d.
D
DxR
The horizontal deflection at in the primary structure due to external loading is
given byL D
=D
A
v
L dxEI
MM(2)
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
6/22
wherev
M is the internal virtual moment resultant in the frame due to virtual load
applied at along the resultant andD DxR M is the internal bending moment of the
frame due to external loading (for details refer to Module 1,Lesson 5).Thus,
( ) ( ) ++=6
0
6
0
6
0
2
06)936(12 dxEI
xdxEI
xdxEI
xxxL
(span AB, origin at A) (span BC, origin at B) (span DC, origin at )D
EIL
864= (3)
In the next step, calculate the displacement at when a real unit load is
applied at in the direction of
11a DD
DxR (refer to Fig.11.1 d). Please note that the same
Fig. 11.1d is used to represent unit virtual load applied at and real unit loadapplied at . Thus,
D
D
dxEI
mma
D
A
v
=
11
6 6 62 2
0 0 0
36x dx dx xdx
EI EI EI= + +
EI360= (4)
Now, the compatibility condition of the problem may be written as
011 =+ DxL Ra (5)
Solving,
kN40.2=Dx
R (6)
The minus sign indicates that the redundant reaction acts towards left.
Remaining reactions are calculated from equations of static equilibrium.DxR
0 12 2.40 9.60 kN (towards left)x Ax
F R= = + =
0 9 kN (dowwards)D Ay
M R= =
9 kN (upwards)DyR = +
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
7/22
The bending moment diagram for the frame is shown in Fig. 11.1e
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
8/22
Example 11.2
Analyze the rigid frame shown in Fig.11.2a and draw the bending moment and shearforce diagram. The flexural rigidity for all members is the same. Neglect axialdeformations.
Five reactions components need to be evaluated in this rigid frame; hence it is
indeterminate to second degree. Select )( 1RRcx = and )( 2RRcy = as the redundant
reactions. Hence, the primary structure is one in which support A is fixed and thesupport C is free as shown in Fig.11.2b. Also, equations for moments in variousspans of the frame are also given in the figure.
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
9/22
Calculate horizontal and vertical1)( L 2)( L deflections at C in the primary structure
due to external loading. This can be done by unit load method. Thus,
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
10/22
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
11/22
096
)3)(2496(
)(
3
0
3
0
1 ++++
= dxEIx
dxEI
xxL
(Span DA, origin at D) (Span BD, origin at B) (span BC, Origin B)
2268
EI= (1)
0)2(48
)4(96
)4)(2496(
)(
2
0
3
0
3
0
2 +
+
++
= EIdxxx
EI
dx
EI
dxxL
(Span DA, origin at D) (Span BD, origin at B) (Span BE, origin at E)(Span EC, Origin C)
( )2
3056L
EI = (2)
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
12/22
In the next step, evaluate flexibility coefficients, this is done by applying a unit load
along, and determining deflections and corresponding to and
respectively (vide, Fig .11.2 c). Again apply unit load along and evaluate
deflections and corresponding to and and respectively (ref.
Fig.11.2d).
1R 11a 21a 1R 2R
2R
22a 12a 2R 1R
EIdx
EI
xa
726
0
2
11 == (3)
0)4(
6
0
2112 +
== dxEIx
aa
EI
72= (4)
and
+=6
0
4
0
2
22
)(16dx
EI
xdx
EIa
EI
33.117= (5)
In the actual structure at C, the horizontal and vertical displacements are zero.Hence, the compatibility condition may be written as,
0)( 2121111 =+= RaRaL
(6)2 12 1 22 2( ) 0L a R a R = + =
Substituting the values of ,1)( L 2)( l , , and in the above equations and
solving for and , we get
11a 12a 22a
1R 2R
(towards left)kN056.11 =R
(upwards)kN44.272 =RThe remaining reactions are calculated from equations of statics and they are shownin Fig 11.2e. The bending moment and shear force diagrams are shown in Fig. 11.2f..
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
13/22
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
14/22
11.2 Support settlements
As discussed in the case of statically indeterminate beams, the reactions areinduced in the case of indeterminate frame due to yielding of supports even whenthere are no external loads acting on it. The yielding of supports may be either linear
displacements or rotations of supports (only in the case of fixed supports) .Thecompatibility condition is that the total displacement of the determinate frame(primary structure) due to external loading and that due to redundant reaction at agiven support must be equal to the predicted amount of yielding at that support. If thesupport is unyielding then it must be equal to zero.
Example 11.3
A rigid frame is loaded as shown in the Fig 11.3a, Compute the reactions if thesupport settles by 10 mm. vertically downwards. Assume
ABC
D EI to be constant for all
members. Assume .4 2200 10E GPa and I m= =
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
15/22
This problem is similar to the previous example except for the support settlement.Hence only change will be in the compatibility equations. The released structure is
as shown in Fig.11.3b .The deflections 1)( L and 2)( L at Cin the primary structure
due to external loading has already been computed in the previous example. Hence,
EIL2052
)( 1 = (1)
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
16/22
EIL
3296)( 2
= (2)
Therefore,
mL 1026.0)( 1 =
mL 1635.0)( 2 =
The flexibility coefficients are,
EIa
7211 = (3)
EIaa
722112
== (4)
EIa
33.11722 = (5)
Now, the compatibility equations may be written as,
0)( 2121111 =++ RaRaL
(6)32221212 1010)(=++ RaRaL
Solving which,
(towards left)kN072.21 =R
(upwards) (7)kN4.262 +=R
The reactions are shown in Fig.11.3c.
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
17/22
Example 11.4
eactions of the rigid frame shown in Fig.11.4a and draw bendingCompute the rmoment diagram .Also sketch the deformed shape of the frame. Assume EI to beconstant for all members.
elect vertical reaction at C, as the redundant .Releasing constraint againstS 1R
redundant, the primary structure is obtained. It is shown in Fig.11.4b.
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
18/22
The deflection in the primary structure due to external loading can be
calculated from unit load method.1)( L
=3
0
1
)4)(12()(
EI
dxxL
(span DA, origin at D)
EI
216= (Downwards) (1)
Now, compute the flexibility coefficient,
+=4
0
6
0
2
11
16dx
EIdx
EI
xa
EI
33.117= (2)
The compatibility condition at support Cis that the displacement at Cin the primarystructure due to external loading plus the displacement at Cdue to redundant mustvanish. Thus,
033.117216
1 =+
REIEI
(3)
Solving,
(4)kN84.11 =R
The remaining reactions are calculated from static equilibrium equations. They areshown in Fig.11.4d along with the bending moment diagram.
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
19/22
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
20/22
To sketch the deformed shape/elastic curve of the frame, it is required to computerotations of joints B and and horizontal displacement of C. These joint rotationsand displacements can also be calculated from the principle of superposition .Thejoint rotations are taken to be positive when clockwise. Towards this end first
calculate joint rotations at
C
)( BLB and )( CLC and horizontal displacement at in the
released structure (refer to Fig.11.4b).This can be evaluated by unit load method.
C
EIdx
EI
xBL
54)1)((123
0
=
= (5)
EIdx
EI
xCL
54)1)(12(3
0
=
= (6)
+
=
3
0
)3(12 dxEI
xxCLEI270= (7)
Next, calculate the joint rotations and displacements when unit value of redundant is
applied (Fig.11.4c). Let the joint rotations and displacements be CRBR , and .CR
=6
0
4
EI
dxBR
EI
24= (8)
EIdx
EIdx
EI
xCR
32)1)(4()1)(( 6
0
4
0
=+= (9)
=
=6
0
72)4(
EIdx
EI
xCR (10)
Now using the principle of superposition, the actual rotations and displacements atthe joints may be obtained.
1RBRBLB
+= (11)
54 24 1.84 9.84
EI EI E
= + =
I
(Clockwise rotation)
1RCRCLC += (12)
EIEIEI
88.484.13254=
+
=
(Counterclockwise rotation)1RCRCLC += (13)
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
21/22
EIEI
84.172270 =
EI
52.137= (towards right)
The qualitative elastic curve is shown in Fig. 11.4h.
Version 2 CE IIT, Kharagpur
7/31/2019 m2l11 Lesson 11 The Force Method of Analysis: Frames
22/22
Summary
In this lesson, the statically indeterminate plane frames are analysed by forcemethod. For the purpose of illustrations only bending deformations of the frame areconsidered as the axial deformations are very small. The problem of yielding of
supports in the case of plane frames is also discussed. The procedure to drawqualitative elastic curve of the frame is illustrated with the help of typical example.The bending moment and shear force diagrams are also drawn for the case of planeframe.
Version 2 CE IIT Kharagpur