Magnetostrictive Liquid Level Transmitters with Temposonics · 2018-04-11 · ‘Generalized Crude Oils’, Correction of Volume to 60 °F against API . Gravity. 6B Light Oils ‘Generalized

Level Plus®

Operation Manual

Magnetostrictive Liquid Level Transmitterswith Temposonics® Technology

RefineME®

2

Level Plus® RefineME®

Operation Manual

Table of contents

1. Contact information ....................................................................32. Terms and definitions .................................................................43. Introduction .................................................................................64. Safety instructions ......................................................................6

4.1 Intended use ......................................................................... 64.2 Forseeable misuse ................................................................ 64.3 Installation, commissioning, and operation .......................... 6

5. Product overview ........................................................................65.1 Components .......................................................................... 75.2 Accuracy ............................................................................... 85.3 Warranty ............................................................................... 85.4 Storage ................................................................................. 85.5 Model number identification (Order code) ............................ 95.6 Specifications ...................................................................... 11

6. Installation and mounting ........................................................126.1 Training ............................................................................... 126.2 Stilling wells and guide poles .............................................. 126.3 Tools ................................................................................... 126.4 Installation steps ................................................................. 126.5 Mounting ............................................................................ 12

7. Electrical connections ..............................................................137.1 Basic information ................................................................ 137.2 Safety recommendations .................................................... 137.3 Industrial topologies ........................................................... 137.4 Cable recommendations ..................................................... 147.5 Electrical conduit ................................................................. 147.6 Grounding ........................................................................... 15

7.6.1 Safety grounding ........................................................ 157.6.2 Shield grounding ........................................................ 15

7.7 Safety barriers ..................................................................... 158. Commissioning .........................................................................16

8.1 Training ............................................................................... 168.2 Tools ................................................................................... 168.3 Setup software .................................................................... 168.4 Commissioning steps ......................................................... 16

8.4.1 Modbus or DDA ......................................................... 168.4.2 HART® ....................................................................... 16

9. Maintenance .............................................................................169.1 Training ............................................................................... 169.2 Tools ................................................................................... 169.3 Inspection ........................................................................... 169.4 Preventative maintenance ................................................... 17

9.4.1 General Purpose Applications .................................... 179.4.2 Severe Service Purpose Applications ......................... 17

Repair ........................................................................................ 1710.1 RMA policy ....................................................................... 1710.2 Training ............................................................................. 1710.3 Tools ................................................................................. 1710.4 Troubleshooting ................................................................ 1810.5 Setup software .................................................................. 18

Interface .................................................................................... 1811.1 Modbus ............................................................................. 1811.2 DDA .................................................................................. 1811.3 HART® .............................................................................. 18

12. Agency information ................................................................. 1912.1 Approvals overview ......................................................... 1912.2 Certificates ...................................................................... 2012.3 FM (NEC) ........................................................................ 20 12.3.1 Intrinsically Safe .................................................. 20 12.3.1.1 Special conditions of safe use ................ 20 12.3.1.2 Labels .................................................... 20 12.3.1.3 Installation drawing ................................ 21 12.3.2 Explosionproof / Flame proof ............................... 25 12.3.2.1 Special conditions of safe use ................ 25 12.3.2.2 Labels .................................................... 25 12.3.2.3 Installation drawing ................................ 2612.4 FMC (CEC) ...................................................................... 30 12.4.1 Intrinsically Safe .................................................. 30 12.4.1.1 Special conditions of safe use ................ 30 12.4.1.2 Labels .................................................... 30 12.4.1.3 Installation drawing ................................ 31 12.4.2 Explosionproof / Flame proof ............................... 35 12.4.2.1 Special conditions of safe use ................ 35 12.4.2.2 Labels .................................................... 35 12.4.2.3 Installation drawing ................................ 3612.5 ATEX and IECEx .............................................................. 40 12.5.1 Intrinsically Safe .................................................. 40 12.5.1.1 Special conditions of safe use ................ 40 12.5.1.2 Labels .................................................... 40 12.5.1.3 Installation drawing ................................ 41 12.5.2 Flame proof .......................................................... 45 12.5.2.1 Special conditions of safe use ................ 45 12.5.2.2 Labels .................................................... 45 12.5.2.3 Installation drawing ................................ 46 12.5.3 EC Declaration of Conformity ............................... 50

10.

11.

3


Operation Manual

1. Contact information

United States

GeneralTel: +1-919-677-0100Fax: +1-919-677-2343E-mail: [email protected]://www.mtssensors.com

Mailing and shipping addressMTS Systems CorporationSensors Division3001 Sheldon DriveCary, North Carolina, 27513, USA

Customer serviceTel: +1-800-633-7609Fax: +1-800-498-4442E-mail: [email protected]

Technical support and applications24 Hour Emergency Technical SupportTel: +1-800-633-7609e-mail: [email protected]

Germany

GeneralTel.: +49-2351-9587-0Fax: +49-2351-56491e-mail: [email protected]://www.mtssensors.com

Mailing and shipping addressMTS Sensor Technologie, GmbH & Co. KGAuf dem Schüffel 9D - 58513 Lüdenscheid, Germany

Technical support and applicationsTel.: +49-2351-9587-0e-mail: [email protected]://www.mtssensors.com

Japan

GeneralTel.: +81-42-775-3838Fax: +81-42-775-5516 e-mail: [email protected]://www.mtssensors.com

Mailing and shipping addressMTS Sensors Technology Corporation737 Aihara-cho, Machida-shiTokyo 194-0211, Japan

Technical support and applicationsTel.: +81-42-775-3838Fax: +81-42-775-5512

mailto:info.us%40mtssensors.com?subject=More%20info

http://www.mtssensors.com

mailto:[email protected]

mailto:levelplus%40mts.com?subject=Level%20plus%20info

mailto:info.de%40mtssensors.com?subject=More%20info


mailto:info.de%40mtssensors.com?subject=More%20info


mailto:info.jp%40mtssensors.com?subject=More%20info


4


Operation Manual

2. Terms and definitions

6A Heavy Oils‘Generalized Crude Oils’, Correction of Volume to 60 °F against API Gravity.

6B Light Oils‘Generalized Products’, Correction of Volume to 60 °F against API Gravity.

6C Chemical‘Volume Correction Factors (VCF)’ for individual and special applica-tions, volume correction to 60 °F against thermal expansion coeffi-cients.

6C ModAn adjustable temperature reference for defining VCF.

A

API Gravity The measure of how heavy or light a petroleum liquid is compared to

water. Allowable values are 0 to 100 degrees API for (6A) and 0 to 85 degrees API for (6B).

D

DDA ‘Direct Digital Access’ – The proprietary digital protocol developed by

MTS for use in intrinsically safe areas.

Density Mass divided by the volume of an object at a specific temperature. The

density value should be entered as lb / cu. ft..

E

Explosionproof Type of protection based on enclosure in which the parts which can

ignite an explosive gas atmosphere are placed within, and which can withstand the pressure developed during an internal explosion of an ex-plosive mixture, and which prevents the transmission of the explosion to the explosive gas atmosphere surrounding the enclosure.

F

Flame proof Type of protection based on enclosure in which the parts which can

ignite an explosive gas atmosphere are placed within and which can withstand the pressure developed during an internal explosion of an ex-plosive mixture, and which prevents the transmission of the explosion to the explosive gas atmosphere surrounding the enclosure.

FOUNDATION™ fieldbus An all digital, serial, two-way communications system that serves as

the base-level network in a plant or factory automation environment. Developed and administered by the fieldbus FOUNDATION™.

G

GOVI ‘Gross Observed Volume of the Interface’ – The total volume of the tank

occupied by the interface liquid. The GOVI is only given when mea-suring two liquids and is calculated by subtracting the volume of the product from the total volume of liquid in the tank (GOVT – GOVP).

GOVP ‘Gross Observed Volume of the Product’ – The total volume of the tank

occupied by the product liquid. When measuring only one liquid, it is also the total volume of liquid in the tank (GOVT). When measuring two liquids it is the total volume of liquid in the tank minus the volume of the interface liquid (GOVT – GOVI).

GOVT ‘Total Gross Observed Volume’ – The total volume of liquid in the tank.

When measuring only one liquid it is equal to the volume of the product (GOVP). When measuring two liquids it is equal to the volume of the product and interface liquids (GOVP + GOVI).

GOVU ‘Gross Observed Volume Ullage’ – the difference in volume between the

working capacity of a tank and the total volume in the tank (Working Capacity – GOVT).

H

HART® A Bidirectional communication protocol that provides data access

between intelligent field instruments and host systems.

I

Interface Noun; The measurement of the level of one liquid when that liquid is

below another liquid.

Interface Adj.; The Software Graphical User Interface (GUI) that allows the user

to access software protocols (HART, DDA, MODBUS).

Intrinsic safety ‘Intrinsically safe’ - Type of protection based on the restriction of

electrical energy within apparatus of interconnecting wiring exposed to potentially explosive atmosphere to a level below that which can cause ignition by either sparking or heating effects.

5


Operation Manual

M

Mass The property of a body that causes it to have weight in a gravitational

field, calculated by density at the reference temperature multiplied by the volume correction factor (Density * VCF).

MODBUS A serial communications protocol published by Modicon in 1979 for

use with its programmable logic controllers (PLCs). It has become a de facto standard communications protocol in industry, and is now the most commonly available means of connecting industrial electronic devices.

N

NEMA Type 4X A product Enclosure intended for indoor or outdoor use primarily to

provide a degree of protection against corrosion, windblown dust and rain, splashing water, and hose-directed water; and to be undamaged by the formation of ice on the enclosure. They are not intended to provide protection against conditions such as internal condensation or internal icing.

NPT U.S. standard defining tapered pipe threads used to join pipes and

fittings.

NSVP ‘Net Standard Volume of the Product’ – The temperature corrected

volume for the product liquid in the tank, requires the transmitter to be ordered with temperature measurement capabilities. The NSVP is calculated by multiplying the volume of the product liquid by a volume correction factor based on temperature (GOVP * VCF).

R

Reference Temperature The temperature at which the density measurement is given, the allow-

able values are 32 °F to 150 °F.

S

Specific Gravity The density ratio of a liquid to the density of water at the same condi-

tions.

Sphere Radius The internal radius of the sphere that contains the liquid, the value is

used to calculate the volume along with the Sphere Offset.

Sphere Offset An offset value that accounts for additional volume in a sphere from

non-uniform sphere geometry, the value is used to calculate the volume along with the Sphere Radius.

Strap TableA table of measurement correlating the height of a vessel to the volume that is contained at that height. The transmitter can contain up to 100 points.

T

TEC ‘Thermal Expansion Coefficient’ - a value correlating the change in tem-

perature for an object with the change in its volume. Allowable values are 270.0 to 930.0. TEC units are in 10 E-6/Deg F.

Temperature Correction Method One of five product correction methods used to correct the product

volume in the tank due to changes in temperature from 60 °F including (6A, 6B, 6C, 6C Mod, and Custom Table.

V

Volume Calculation Mode One of two methods use to calculate volume measurements from level

measurements, including Sphere and Strap Table.

VCF ‘Volume Correction Factor’ – A table of measurements correlating

temperature points with correction factors for the liquids expansion/contraction. The transmitter can contain up to 50 points.

W

Working Capacity The maximum volume of liquid that the user desires for their vessel to

hold, typically 80% of the vessels maximum volume before overfill.

6


Operation Manual

3. Introduction

3.1 Purpose and use of this manual

The content of this technical documentation and of its various annexes is intended to provide information on mounting, installation and commissioning by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians.

3.2 Used symbols and warningsWarnings are intended for your personal safety and for avoidance of damage to the described product or connected devices. In this documentation, safety information and warnings to avoid dangers that might affect the life and health of personnel or cause material damage are highlighted by the preceding pictogram, which is defined below.

4. Safety instructions

4.1 Intended useThe liquid level transmitter is intended to be used to measure the level of liquid(s) contained by a structure as well as the temperature of the liquid. The product may only be used for the applications defined under item 1 to item 4 below and only in conjunction with third-party devices and components recommended or approved by MTS Sensors. As a prerequisite of proper and safe operation, the product requires correct transport, storage, mounting and commissioning and must be operated with utmost care.

1. Application does not exceed product’s performance specification in section 5.6.

2. Product may only be installed in hazardous areas as specified by approval certifications in section 12 following special conditions of safe use outlined in section 12 or in safe areas.

3. The liquid(s) being measured are compatible with the selected wetted parts of the product.

4. MTS floats should be used for proper functionality and safety approval.

4.2 Foreseeable misuse

Symbol Meaning

NOTICE This symbol is used to point to situationsthat may lead to material damage and/or personal injury.

4.3 Installation, commissioning and operation

1. Wear proper personal protection equipment such as hard hat, safety shoes, flame resistant clothing, safety glasses, gloves, and hearing protection.

2. Follow the specifications given in the technical documentation.3. Two (2) individuals are recommended to conduct proper installati-

on, commissioning, and repair of the level transmitter.4. Ensure the equipment used in a hazardous environment is selected

and installed in compliance with regulations governing the geogra-phical installation and facility. Only install equipment that complies with the types of protection relevant to the applicable classes, division, zones, category, gas group, and temperature code.

5. Protect the sensor against mechanical damage during installation and operation.

6. Do not use damaged products and secure them against unintentio-nal use. Mark damaged products as being defective.

7. Connect the sensor very carefully and pay attention to the polarity of connections. MTS recommends to not make connections while power is live.

8. Before turning on power, ensure that nobody’s safety is jeopar-dized by starting level transmitter and/or process.

9. Regularly follow preventative maintenance to prevent safety risks.10. Make sure that no wire strands are loose or sticking out of the

terminal block connection which could short and cause a problem.11. Make sure that no wire strands, including shield, are in contact

with the electronic module enclosure.

5. Product overview

The Level Plus® RefineME® Liquid-Level transmitter is a continuous multi-functional magnetostrictive transmitter that provides product level, interface level, and temperature to the user Modbus, DDA, Ana-log (4-20 mA), or HART®. Magnetostrictive technology is one of the most accurate and repeatable level technologies available to date.

Forseeable misuse Consequence

Process Temperature out of rangeSignal Degradation, Possible Damage to SensorSee Section 5.6 for Specifications

Power Supply out of rangeNo Communication, Possible Damage to SensorSee Section 5.6 for Specifications

Process Pressure out of rangePossible Damage to Sensor,See Section 5.6 for Specifications

Improper Chemical Compatibility

Possible Damage to Sensor,Customer Must Select Wetted Material that is compatible with liquid(s) in tank

Modifying SensorWarranty Void, Hazardous Approval Void, Customer should contact factory for custom unit

Improper GroundingPossible Damage to Sensor, Full Protection Compromised,See Section 7.6 for Grounding

Forseeable misuse Consequence

Wrong sensor connectionPossible damage to electronicsSee Section 7 for Electrical Connections

Improper InstallationPhysical damage to packagingSee Section 6 for Installation

Installation in unapproved Hazardous Area

Potential SparkSee Section 12 for Agency Information

Table 1: Foreseeable misuse

Important:Before starting the operation of the equipment read this documentation thoroughly and follow the safety information.

7


Operation Manual

Industries » Petroleum » Liquid Petroleum Gas » Food & Beverage » Chemical » Mining

Applications » Fuel Additive Tanks » Sump Tanks » Bullet Tanks » Separator Tanks » Battery Tanks » Storage Tanks » Solvent Extraction

Features » 3-in-1 Measurement

» Product Level » Interface Level » Temperature

» No scheduled maintenance or recalibration » Field Repairable » Inherent Accuracy ±1mm » 200 Point Strap Table » API Temperature Corrected Volumes

5.1 ComponentsThe Level Plus® RefineME® liquid level transmitter consists of four main components; a housing, outer pipe, float, and electronics. Varying the components of the transmitter allows the transmitter to be customized to almost any application.

HousingsLevel Plus® RefineME® transmitters are available in three housing confi-gurations; NEMA Type 4X 316L stainless steel, explosionproof single and dual-cavity housings as shown:

Fig. 3: Dual cavity explosion-proof housing

Fig. 2: Single cavity explosion-proof housing

Fig. 1: NEMA Type 4X 316L Stainless Steel housing

1

1

2

2

3

3

4

4

A A

B B

C C

D D

REV ECO # DESCRIPTION

TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF

UNLESS OTHERWISE SPECIFIEDTOLERANCES

0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1

- THREAD DEPTHS ARE TO MIN. FULL THDS- DRILL DEPTHS ARE TO FULL DIA.- REMOVE BURRS AND SHARP EDGES- DO NOT SCALE PRINT- MACHINED SURFACE FINISH 3.2uM [125 uIn]

PROPRIETARY DATATHE INFORMATION AND DESIGN(S) DISCLOSEDHEREIN ARE THE PROPERTY OF MTS SYSTEMSCORPORATION AND MAY NOT BE USED,REPRODUCED OR DISCLOSED IN ANY FORMEXCEPT AS GRANTED IN WRITING BY MTSSYSTEMS CORPORATION. THIS RESTRICTIONEXCLUDES INFORMATION THAT IS IN THE PUBLIC DOMAIN OR WAS LEGITIMATELY IN THEPRIOR POSSESSION OF THE RECIPIENT.

mMTS SYSTEMS CORPORATIONSENSORS DIVISION3001 SHELDON DRIVE, CARY, NC 27513

METRIC

FIRST ANGLE C LL drawing

1 1

DRAWN BY:

114 mm(4.5 in.)

127 mm(5 in.)

124 mm(4.9 in.)

132 mm(5.2 in.)

87 mm(3.4 in.)

109 mm(4.3 in.)

75 mm(3 in.)

206 mm(8.1 in.)

127 mm(5 in.)

117 mm(4.6 in.)

145 mm(5.7 in.)

1

1

2

2

3

3

4

4

A A

B B

C C

D D


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY:

114 mm(4.5 in.)

127 mm(5 in.)

124 mm(4.9 in.)

132 mm(5.2 in.)

87 mm(3.4 in.)

109 mm(4.3 in.)

75 mm(3 in.)

206 mm(8.1 in.)

127 mm(5 in.)

117 mm(4.6 in.)

145 mm(5.7 in.)

1

1

2

2

3

3

4

4

A A

B B

C C

D D


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY:

114 mm(4.5 in.)

127 mm(5 in.)

124 mm(4.9 in.)

132 mm(5.2 in.)

87 mm(3.4 in.)

109 mm(4.3 in.)

75 mm(3 in.)

206 mm(8.1 in.)

127 mm(5 in.)

117 mm(4.6 in.)

145 mm(5.7 in.)

MTS is the inventor and purveyor of magnetostrictive technology and has been serving the level industry for over 35 years.

Fig. 4: Stainless Steel single cavity housing

1

1

2

2

3

3

4

4

A A

B B

C C

D D

TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE: SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC

FIRST ANGLE C

1 1

DRAWN BY:

REV ECO# DESCRIPTION BY DATE

178 mm(7 in.)

135 mm(5.30 in.)

135 mm(5.3 in.)

152 mm(6 in.)

1

1

2

2

3

3

4

4

A A

B B

C C

D D

TITLE

SIZE DWG NO. REV



0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC

FIRST ANGLE C

1 1

DRAWN BY:


178 mm(7 in.)

135 mm(5.30 in.)

135 mm(5.3 in.)

152 mm(6 in.)

1

1

2

2

3

3

4

4

A A

B B

C C

D D


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY:

114 mm(4.5 in.)

127 mm(5 in.)

124 mm(4.9 in.)

132 mm(5.2 in.)

87 mm(3.4 in.)

109 mm(4.3 in.)

75 mm(3 in.)

206 mm(8.1 in.)

127 mm(5 in.)

117 mm(4.6 in.)

145 mm(5.7 in.)

8


Operation Manual

Internal electronicsAll transmitters come with two electronic components of a sensing element and a board set. Rigid sensing elements are standard on RefineME® . Flexible sensing elements may be ordered on request. The board set consists of up to three electronic boards and a display. The display is capable of displaying the product level, interface level, and temperature. Designed into the display are five buttons for local setup of level transmitter using the stylus.

A temperature sensing function is optional with the RefineME® transmitter. The temperature sensing device is a Digital Thermometer mounted inside the transmitter’s outer pipe assembly. The RefineME® can be ordered with 1, 5, 12, or 16 temperature points.

AccessoriesMTS also offers a series of displays, housings, converters, and other accessories, please refer to the ‘Accessories Catalog’, MTS part number 551103.

5.2 AccuracyFor magnetostrictive transmitters inherent accuracy is measured in terms of non-linearity. Non-linearity is a measurement of any imperfections in the waveguide that are reflected in the linearity of the transmitter’s output. MTS tolerances reflect a maximum non-linearity of ± 1mm. MTS is able to achieve such strict tolerances by manufacturing all of its own waveguide from a proprietary alloy and testing 100% of all transmitters before shipping.

5.3 Warranty

All Level Plus® transmitters come with a two year limited warranty from the factory shipment date. An additional extended warranty can be purchased. A Return Materials Authorization (RMA) number is required and must accompany any transmitter returns. Any unit that was used in a process must be properly cleaned in accordance with OSHA standards, before it is returned to the factory. A Material Safety Data Sheet (MSDS) must also accompany the transmitter that was used in any process.

5.4 StorageIf storage is required prior to installation, store indoors in a dry environment at ambient temperature range not to exceed -40°C (-40°F) to 71°C (160°F).

Important:Contact Technical Support or Customer Service for assistance if you suspect that the transmitter is not working correctly. Technical support can assist you with troubleshooting, part replacement, and Returned Material Authorization (RMA) information if required. Floats

RefineME® transmitters offer numerous floats for different applications such as stainless steel, 3-A sanitary, Hastelloy, Teflon, and Nitrophyl® for both product level and interface level. To be able to accurately detect the interface level there needs to be a difference of at least 0.05 in specific gravities between the product and interface liquids. For detailed information about floats, refer to the ‘Accessories Catalog’, MTS part number 551103.

For assistance with selecting a specific float for your application, please contact Technical Support with the following information: » Specific gravity of liquid(s) being measured » Process temperature » Process opening size » Vessel pressure

RefineME® transmitters should be used with a float having an offset weight and made of stainless steel or Hastelloy C. This allows the float to stay in contact with the pipe to prevent the buildup of an electrostatic charge. For detailed information about floats, refer to the ‘Accessories Catalog’, MTS part number 551103.Non-metallic floats with a projected surface area of less than 5,000 mm² should only be used in Zone 0, Gas group IIA such as float part numbers 201643-2, 201649-2, 201650-2, 201109, 251115 and 251116. All other non-metallic floats offered by MTS such as, 251939, 251119 and 251120 should not be used in a hazardous area application.

Outer pipe configurationsThe outer pipe is constructed of a variety of configurations. The Refine-ME® is available in a rigid pipe. For other pipe options please consult other MTS options such as Tank Slayer®, SoClean®, and/or USTDII.

1

1

2

2

3

3

4

4

A A

B B

C C

D D


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC

FIRST ANGLE C Marketing

1 1

DRAWN BY:

***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION TO APPROVAL AGENCY(S).***

Order length

Order Length

3/4 in NPTAdjustable fitting

Pipe diameter16mm (0.625 in)

Tip of transmitter

Tank Flange(Provided by customer)

127 [5] minimum

Tank Flange

1 in NPT or BSPP Adjustablecompression fitting, male

127mm [5 in ]

Order Length

Pipe diameter (0.625 in. dia)constructed of 316l stainless steel

Sanitary process connection (sanitary cap)

304.8 mm(12 in.)

Fig. 5: Outer pipe configuration

9


Operation Manual

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

L P R16 17 18 19 20 21 22

a b c d e kf g h i j l m n o p

5.5 Model number identification (Order code)

j DT placement

F Evenly spaced per API

C Custom

X None

a Sensor model

L P R RefineME® Level Transmitter

d Electronics mounting

1 Standard

f Materials of construction (Wetted parts)

1 316L stainless steel

3 Hastelloy C

A Teflon

C CRN-Canadian Registration Number (FMC approval only)

c Housing type

A NEMA housing w/cable

B NEMA housing w/terminal

C NEMA housing w/connector

D Single cavity with display

E Dual cavity with display

L SS single cavity w/display

g Process connection type

1 NPT adjustable (3/4 in. only)

2 BSPP adjustable (3/4 in. only)

6 150 lb. welded RF flange



A PN16, DIN 2572 welded flange

B PN40, DIN 2572 welded flange

C PN64, DIN 2572 welded flange

D PN100, DIN 2572 welded flange

Note: Contact factory for other materials

h Process connection size

A 3/4 in. - NPT or BSPP only

D 2 in. (DN50)

E DN65

F 3 in. (DN80)

G 4 in. (DN100)

H 5 in. (DN 125)

J 6 in. (DN150)

X None

i Number of DT‘s (Digital Thermometer)

0 None

1 One DT

5 5 DTs (Modbus or DDA)

K Twelve DTs (Modbus only)

M Sixteen DTs (Modbus only)

k Notified body

C CEC (FMC)

E ATEX

F NEC (FM)

I IEC

X None

e Sensor pipe

B 5/8“ OD Rigid Pipe

(Continued on next page)

b Output

M Modbus

D DDA

1 1 Loop with HART®

2 2 Loop with HART®

5 1 Loop with HART® and SIL2

7 2 Loop with HART® and SIL2 Loop 1 only

* Only for Housing Type D, E, or L

l Protection method

F Explosionproof / Flame Proof*

I Intrinsically Safe

X No approval

10


Operation Manual

n Unit of measure

M Metric - Millimeters

U US customary - Inches

1 2 3 4 5 6 7 8 9 10 11

ORDERING NOTE

Accessories such as floats, cables, and remote displays have to be ordered separately. All accessories are shown in the Accessories Catalog (551103).

L P R

a b c d e f g h i

p Special

S Standard Product

m

o Length (no decimal spaces)

X X X X X Rigid pipe: 12 to 300 in. (code as 01200 to 30000

X X X X X Rigid pipe: 305 to 7620 mm (code as 00305 to 07620)

12 13 14 15 16 17 18 19 20 21 22

kj l m n o p

5.5 Model number identification (Order code) (continued)

Gas group

A Group A**

B Group B

C Group C

D Group D

3 IIC (Instrinsically Safe only)

4 IIB + H2 (Explosion Proof / Flameproof only)

X None

m

** Group A not available with C=CEC (FMC) notified body and F=Flameproof/Explosion Proof protection method

11


Operation Manual

5.6 Specifications (Technical data)

Level Output

Measured Variable Product level and interface level

Output Signal /Protocol Modbus RTU, DDA, Analog (4-20 mA), HART®

Order Length Rigid Pipe: 305 mm (12 in.) to 7620 mm (300 in.) ∆§

Inherent Accuracy ±1 mm (0.039 in.)

Repeatability 0.001% F.S. or 0.381 mm (0.015 in.) *(any direction)

Temperature Output

Measured Variable Average and multipoint temperatures (Modbus, DDA)Single point temperature (Analog, HART®)

Temperature Accuracy (Modbus, DDA) ±0.2 ºC (0.4 ºF) range -40 ºC (-40 ºF) to -20 ºC (-4 ºF),±0.1 ºC (0.2 ºF) range -20 ºC (-4 ºF) to 70 ºC (158 ºF),±0.15 ºC (0.3 ºF) range 70 ºC (158 ºF) to 100 ºC (212 ºF),±0.5 ºC (0.9 ºF) range 100 ºC (212 ºF) to 105 ºC (221 ºF)

Temperature Accuracy (Analog, HART®) ±0.28 ºC (0.5 ºF) range -40 ºC (-40 ºF) to 105 ºC (221 ºF)

Electronics

Input Voltage 10.5 to 28 Vdc

Fail Safe High, Full scale (Modbus, DDA)Low, 3.5 mA default or High, 22.8 mA (Analog, HART®)

Reverse Polarity Protection Series diode

EMC EN 61326-1, EN 61326-2-3, EN 61326-3-2, EN 61000-6-2, EN 61000-6-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11

Environmental

Enclosure Rating NEMA Type 4X, IP65

Humidity 0 to 100% relative humidity, non-condensing

Operating Temperatures Electronics: -40 °C (-40 °F) to 71 °C (160 ºF)Sensing element: -40 °C (-40 °F) to 125 °C (257 °F) ◊Temperature element: -40 °C (-40 °F) to 105 °C (221 °F)

Vessel Pressure Rigid Pipe: 1000psi (138 bar) Teflon Pipe: 25psi (1.75 bar)

Materials Wetted parts: 316L stainless steel, Hastelloy C, Teflon †Non-wetted parts: 316L stainless steel, Epoxy coated aluminum

Field Installation

Housing Dimensions Single cavity:145 mm (5.7 in.) W x by 127 mm (5 in.) D x 109 mm (4.3 in.) H Dual cavity:117 mm (4.6 in.) W x by 127 mm (5 in.) D x 206 mm (8.1 in.) H Stainless steel single cavity:178 mm (7.1 in.) W x by 135 mm (5.3 in.) D x 153 mm (6 in.) H NEMA Type 4X:87 mm (3.4 in.) W x by 124 mm (4.9 in.) D x 132 mm (5.2 in.) H

Mounting

Rigid Pipe 3/4 in. Adjustable MNPT or BSPP fitting, Flange mount

Wiring

Connections 4-wire shielded cable or twisted pair4570 mm (180 in.) integral cable with pigtail

Electrical Connections

Single and Dual Cavity 3/4 in. FNPT conduit opening, M20 for ATEX/IECEx version

NEMA Type 4X ½ in. FNPT conduit opening

Display

Measured Variables Product level, interface level and temperature* Whichever is greater ∆ Contact factory for longer lengths.

◊ Contact factory for specific temperature ranges.† Contact factory for alternative materials.§ Order length equals the measurement range plus the inactive zone.

12


Operation Manual

Riser

NPT or BSPP fitting

Tank flange(customer suppliedor ordered separately)

Float accessport

Tip of transmitter

N

Fig. 6: Threaded flange mounting for industrial pipe

6. Installation and mounting

6.1 Training

Warning: When the pipe/hose of the LP-Series level transmitter is installed or removed from the tank the release of flammable vapors will occur. Take all necessary precaution when installing or removing the level transmitter due to the release of flammable vapors.

Installation should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

6.2 Stilling wells and guide polesLevel Plus® transmitters can be mounted in slotted or unslotted stilling wells but a slotted stilling well is always preferred. Using a unslotted stilling well will negatively affect performance of any level device as the level in the stilling well can differ from the level in the tank. The Level Plus® transmitter can also be installed to one side of the stilling well to also allow for sampling and manual gauging from the same opening as the automatic tank gauging. Contact Technical Support for details.

Level Plus® transmitters do not require a stilling well for installation. Our transmitters are installed in numerous tanks without stilling wells with no loss in performance. A stilling well is highly recommended for agitated, turbulent, and/or fast filling tanks.

6.3 Tools » Channel Lock pliers » 9/64” Hex Key (Allen wrench) » 3/4” Open End wrench » Common head screwdriver, slotted screwdrive

6.4 Installation steps

Caution:It is recommended that assembly and mounting of this transmitter should not be done alone. To ensure proper and safe assembly of the RefineME® transmitter, a minimum of two (2) individuals are recommended. Gloves are also recommended. PPE may be required for work areas such as safety shoes, safety glasses, hard hat, and fire resistant clothing.

1. Consult Section 4.3 before starting.2. Perform steps 1-10 in section 8.4.1 for Modbus or DDA. Perform steps 1-9 in section 8.4.2 for Analog.3. Remove the stop collar and E-ring. With assistance, feed the pipe through the hole of the removed tank flange until the flange is positioned at the top of the pipe. Insert the threaded portion of the adjustable fitting into the customer supplied flange and tighten (apply pipe thread sealant if required). Be careful not to drop flange on the pipe as damage may result. 4. Slide the product float onto the pipe. Slide the interface float (optional) onto the pipe. Install stop collar 3 inches

from the bottom of rigid section (see ‘Note’ below). Install E-ring. Do not drop float(s) or allow them to free fall along the pipe as damage may result.

Notes:The stop collar can be removed or adjusted based on the float selected for the application. Please consult the factory for more information.

5. Slide float(s) back down to the stop collar to prevent them from free falling during installation into the tank. Insert the pipe and floats through the tank riser pipe and lower the transmitter/float assembly into the tank until it rests on the bottom. 6. Secure the flange onto the tank riser pipe.7. Pull the transmitter upward to straighten the pipe. Tighten the adjustable fitting to hold the transmitter in place. 8. Terminate the field wire cables noting proper wire orientation.

6.5 MountingThe method of mounting the transmitter is dependent on the vessel or tank in which it is being used, and what type of transmitter is being mounted. There are two typical methods for mounting; threaded flange mounting and welded flange mounting.

Threaded flange mountingIn most applications, the RefineME® transmitter can be mounted directly to the tank or flange via a NPT or BSPP threaded fitting, assuming there is a proper threaded connection available. If the float will not fit through the flange opening when the flange is removed, there must be some alternative means to mount the float on the transmitter from inside the vessel; this may require an access port nearby the entry point of the transmitter as shown in Figure 6.

13

7. Electrical connections

7.1 Basic informationA typical intrinsically safe connection for the Level Plus® RefineME® transmitter includes protective safety barriers, a power supply and a reading or monitoring device. Refer to Agency information in Section 12.

A typical explosion proof/flame proof connection for the Level Plus® Tank Slayer® transmitter includes a power supply and a reading or monitoring device. All cabling is in approved conduit with sealoffs as specified by local electrical code. Refer to agency information in Section 12.

7.2 Safety recommendationsBe sure to:1. Always follow applicable local and national electrical codes and observe polarity when making electrical connections. 2. Never make electrical connections to the RefineME® transmitter with power turned on. 3. Make sure that no wire strands are loose or sticking out of the terminal block connection which could short and cause a problem. 4. Make sure that no wire strands, including shield, are in contact with the electronic module enclosure. 5. The electronics module enclosure is grounded through internal circuitry and is electronically isolated from the explosionproof housing.

7.3 Industrial topologiesThere are four topologies described and illustrated below. However, the daisy chain topology is not recommended by MTS.

Point-to-pointThe point-to-point topology consists of having only one device on the loop as shown in Figure 8. This topology is not usually used with a bus network since it does not take advantage of placing multiple devices on a loop.

PLC


Operation Manual

Welded flange

Tank flange

Welding sleeve28.6 mm

(1.13 in.) dia

Product float

Riser

Stainless-steelflexible pipe

Interface float

Bottom-fixing weight,magnet or hook

Fig. 7: Welded flange mounting for industrial pipe

Welded flange mountingThe RefineME® transmitter can also be mounted to a tank flange as shown in Figure 7. First, install float(s) onto the transmitter. Second, install the float retaining hardware on the tip of the transmitter. To complete the installation, mount the transmitter, flange and float(s) as a unit in to the tank.

Fig. 8: Point-to-point topology

14

Notes:1. Tighten housing cover (both front and back covers if dual cavity) to full stop against the O-ring.2. Do not over-tighten compression fittings.3. Use side conduit entry only.4. In high humidity areas, use a breather drain type conduit sealing fitting to minimize moisture intrusion.5. For Division Installations, an approved conduit seal is required within 457 mm (18 in.) of the enclosure.6. For Zone Installations, an approved conduit seal is required within 50mm (2 in.) of the enclosure.

Conduit sealing fitting

NPT or BSPP FittingDo not over-tightencompression fitting!

Interface float(ordered

separately)

Product float(ordered

separately)

View shown withcover removed

Plugged entryDo not use(see notes)

3/4 NPT or M20 conduit accessUse NPT conduit fitting only!

Conduit(flexible or rigid)

Conduit fromcontrol room

Level Plus®

Do not remove cover with circuit energized in hazardous locations!

Follow safe work procedures.


Operation Manual

7.4 Cable recommendationsRefer to ‘Table 2’ below for general requirements of cable types for the Level Plus® RefineME® transmitter.

Cable specifications

7.5 Electrical conduit

Table 2: Cable specification and parameters

Fig. 12: Electrical conduit installation

Bus with spursThe bus with spurs topology has a main trunk cable that has each device connected via its own spur at a junction box as shown in Figure 9. The bus with spurs and tree topologies can also be used together to form a hybrid topology.

Tree alignmentThe tree topology is very similar to the bus with spurs topology with the main difference of having a common junction box for all of the transmit-ters as shown in Figure 10. Bus with spurs and tree topologies can also be used together to form a hybrid topology.

Daisy chainThe daisy-chain topology utilizes a single cable that is connected to all of the transmitters with the cable being interconnected at each field device. When using this topology make sure that the wiring practice allows for one transmitter to be disconnected without disconnecting the entire loop as shown in Figure 11. MTS does not suggest using the daisy-chain topology.

PLC

PLC

Fig. 9: Bus with spurs topology

Fig. 10: Tree topology

Fig. 11: Daisy-chain topology

PLC

Parameter Specification

Minimum cable size 24 to 14 AWG (0.51 to 1.6 mm diameter)

Cable type Single pair shielded or multiple pair with overall shield; minimum 0.010 in. (0.25 mm) insulation thickness

Capacitance Less than 30 pF/ft (98 pF/m)

15


Operation Manual

Entity parameters

Digital supply(1 per LT)

Ui = 28 Vdc

Ii = 100 mA

Ci = 0.0 µF

Li = O mH

Pi = 700 mW

Digital communication(2 per LT)

Ui = 8.6 Vdc

Ii = 10 mA

Ci = 0.0 µF

Li = 0.0 mH

Pi = 21.5 mW

Analog(1 per loop)

Ui = 28 Vdc

Ii = 120 mA

Ci = 0 µF

Li = 5 µH

Pi = 840 mW

Table 3: Safety barrier entity parameter references

Table 4: Safety barrier entity parameter references

7.7 Safety barriersRefer to Table 3 for entity parameters and Table 4 for example safety barriers

7.6 Grounding

7.6.1 Safety grounding

Warning:Grounding the transmitter through a threaded conduit connection does not meet the requirements as a grounding of the sensor for safety.

There are two methods to provide an earth ground connection to the earth ground of the electronics. Either method must result in a resistance of less than 1 Ohm. » Run an earth ground through the conduit and connect directly to the

earth ground lug inside the housing. » Run an earth ground directly to the ground lug on the outside of the

housing.

7.6.2 Shield grounding

Warning:The shield ground does not meet the requirements as grounding of the sensor for Safety.

Immunity performance of the sensor from external sources of surge, burst, RF, radiated emissions and other noise is dependent on a proper ground for the shield of the communications cable. The communications cable shield should be of a braided type and connected to the internal ground lug of the sensor housing.

Runs in a continuous metallic conduit When installed inside a dedicated continuous metallic conduit, the conduit provides a level of shielding protection from external interference and a level of ground to the sensor housing. In this case a foil type shielded cable with a drain wire connected to the internal ground lug may be sufficient. Sharing of the metallic conduit with other cables will result in loss of effective shielding performance of the communication cable and possible degradation in performance of the sensor. In this case a braided type shielded cable connected to the sensor internal ground lug would be recommended. In all cases paralleling the communications cable with any noise generating cable inside of a conduit or with noise generating cables in close proximity to the conduit may degrade the performance of the sensor. Runs without a conduit In some rare applications, or where safety may not be required, a metallic conduit may not exist. The communications cable shield should be of a braided type and connected to the internal ground lug of the sensor housing. Alternatively a safety approved EMC Cable Gland can be used for grounding the shield. Contact MTS for information before using one of these cable glands.

NEC Undesirable currents (ground loops) is a violation of the NEC and is a safety hazard.

Supplier STAHL STAHL STAHL

Type 9001/01-280-100-101

9001/51-280-110-141

9001/01-086-010-101

Maximum voltage 28 Vdc 28 Vdc 8.6 Vdc

Maximum current(each channel)

100 mA 110 mA 10 mA

Maximum power(each channel)

700 mW 770 mW 21.5 mW

Number of channels 1 1 1

Interface Modbus/DDA HART® Modbus/DDA

16


Operation Manual

9.3 InspectionBelow are some standard items that should be inspected on a regular basis to make sure that the level transmitter and surrounding environ-ment are in operating condition.

» Hazardous Area Label is present and legible » Hazardous Area approval is correct for installation » There are no visible unauthorized modifications » Electrical connections are tight » Condition of enclosure O-ring is satisfactory » No water ingress (white powder) » No obvious damage to cable » Sealing of conduit or cable gland is satisfactory » Earth ground is satisfactory » Single or Dual Cavity Enclosure threads are not damaged » Housing o-ring is not damaged or cracked » No corrosion on visible parts » Printed circuit boards are clean and undamaged

9. Maintenance

9.1 TrainingMaintenance should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

9.2 Tools » Channel Lock pliers » 9/64” Hex Key (Allen wrench) » 3/4” Open End wrench

8.4.2 HART®

1. Consult Section 4.3 before starting2. Remove level transmitter from shipping container.3. Remove e-ring and stop collar.4. Insert pipe into float(s) making sure float(s) are in the active range.5. Connect power, HART® to USB converter, and PC6. Open MTS Setup Software.7. Establish Communication.8. Set/Update 4 and 20 mA setpoints9. Disconnect Power and Communication. Remove floats. Prepare flexible level transmitter for transport to the top of the tank.10. Complete Installation in Section 6.4.11. Have qualified technician perform hand measurement. Enter hand measurement into MTS Setup Software and calibrate.12. Store all settings as backup file according to site name and tank number.

8. Commissioning

8.1 TrainingCommissioning should only be conducted by qualified service personnel according to IEC 60079-14 or MTS trained service technicians and local regulations. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

8.2 Tools » Channel Lock pliers » 9/64” Hex Key (Allen wrench) » 3/4” Open End wrench » RS485 to USB Converter (MTS Part # 380114)[Modbus and DDA] » Windows Based PC » Linear Regulated Power Supply » MTS Setup Software » HART® to USB Converter (MTS Part # 380068)[HART®]

8.3 Setup softwareMTS offers Setup Software that is shipped with the level transmitter and is also available for download from www.mtssensors.com. The Setup Software is to be used for installation, commissioning, and troubleshoo-ting. For further details on how to use the setup software consult the Modbus Interface Manual (MTS Part# 551700), the DDA Interface Manual (MTS Part# 551701), and HART® Interface Manual (MTS Part# 551702).

8.4 Commissioning steps

8.4.1 Modbus or DDA

1. Consult Section 4.3 before starting.2. Remove level transmitter from shipping container.3. Remove stop collar.4. Insert pipe into float(s) making sure float(s) are in the active range. Install product float first.5. Connect power, RS485 to USB converter, and PC.6. Open MTS Setup Software.7. Establish Communication.8. For DDA Interface – Set Address. 9. For Modbus Interface – Set Address, Enter Strap Table, Setup Volume Correction Method. 10. Disconnect Power and Communication. Remove floats. Prepare level transmitter for transport to the top of the tank.11. Complete Installation in Section 6.4.12. Have qualified technician perform hand measurement. Enter hand measurement into MTS Setup Software and calibrate.13. Store all settings as backup file according to site name and tank number.

Note:For Additional details consult the protocol specific Modbus Interface Manual (MTS Part #551700), DDA Interface Manual (MTS Part #551701), and HART® Interface Manual (MTS Part #551702).

17


Operation Manual

9.4.1.2 No additional preventative maintenance is necessary. Preventative maintenance suggested for Severe Service Applications may be performed.

9.4.2 Severe Service Applications

9.4.2.1 Perform inspection suggested in section 9.3

9.4.2.2 Disconnect Power.

9.4.2.3 Disconnect process connection from tank. Remove pipe from tank.

9.4.2.4 When the bottom of the pipe is reached inspect the floats.

9.4.2.4.1 If the floats are highly contaminated then remove the assembly from the tank and remove the floats from the pipe.

9.4.2.4.2 If the floats are slightly contaminated then clean the floats without remo-ving the floats from the pipe.

9.4.2.5 Replace pipe and floats in tank.

9.4.2.6 Connect process connection to tank.

9.4.2.7 Connect Power.

9.4.2.8 The process should be carried out regularly until a consistent pattern has been established as to how long the intervals between cleanings should be.

Note:It is best to clean the pipe as it is removed from the tank to minimize the amount of product that is removed from the tank. The user should take caution and abide by all regulations so that product is not spilled and the environment is not contaminated.

9.4 Preventative maintenanceLevel Plus® level transmitters do not typically require preventative maintenance but may require preventative maintenance dependent on the application. For general purpose applications where there is no potential for buildup on the pipe and/or float there is no need for preventative maintenance but routine inspection is still suggested. For severe service applications where there is potential for buildup on the pipe and/or float then preventative maintenance is required.

9.4.1 General purpose applications

9.4.1.1 Perform Inspection suggested in section 9.3

10. Repair

10.1 RMA policy

All Level Plus® transmitters come with a two year limited warranty from the factory shipment date. A Return Materials Authorization (RMA) num-ber is required and must accompany any transmitter returns. Any unit that was used in a process must be properly cleaned in accordance with OSHA standards, before it is returned to the factory. A Material Safety Data Sheet (MSDS) must also accompany the transmitter that was used in any process.

10.2 TrainingRepair should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissio-ning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

10.3 Tools » Channel Lock pliers » 9/64” Hex Key (Allen wrench) » 3/4” Open End wrench » Phillips head screwdriver, plus screwdriver » Common head screwdriver, slotted screwdriver » RS485 to USB Conververter (MTS Part # 380114)[Modbus and DDA] » Windows Based PC » Linear Regulated Power Supply » HART® to USB Converter (MTS Part # 380068)[HART®]

Important:Contact Technical Support or Customer Service for assistance if you suspect that the transmitter is not working correctly. Technical support can assist you with troubleshooting, part replacement, and Returned Material Authorization (RMA) information if required.

18


Operation Manual

10.4 Troubleshooting

Symptom Possible cause Action

No communication with transmitter

No power Check voltage at trans-mitter

Wiring incorrect Reference installation drawing section 12

Wrong address DDA factory default is ‘192 ’Modbus factory default is ‘247 ’

Wrong software Confirm correct software

Wrong protocol Confirm software and transmitter are same protocol

Missing magnet erroror Alarm output

Float not recognized Confirm that the float is attached

Float is in the dead zone

Raise float to see if the error stops

Wrong number of floats selected

Confirm that the number of floats on the transmit-ter and the number of floats the transmitter is attempting to verify are the same.

Trigger level error

Gain needs to be adjusted

Consult Factory

SE is damaged Consult Factory

Min. trigger level too high

Consult Factory

Volume calculation error

No strap table entered

Enter strap table

Level outside range of strap table

Enter additional points in strap table

Strap table incorrect

Check value entries

VCF error No VCF table entered

Enter VCF table

VCF table incorrect Check VCF value entries

Table 5: Troubleshooting reference

11.1 ModbusMTS offers Modbus RTU over a RS485 half-duplex network. For additional information consult Interface Manual Modbus, MTS Part# 551700.

11.2 DDAMTS offers DDA (Direct Digital Access) over a RS485 half-duplex network. For additional information consult Interface Manual DDA, MTS Part# 551701.

11.3 HART®

MTS offers HART® over a 4 to 20 mA signal. For additional information consult HART® Interface Manual, MTS Part# 551702.

10.5 Setup softwareMTS offers Setup Software that is shipped with the level transmitter and is also available for download from www.mtssensors.com. The Setup Software is to be used for installation, commissioning, and troubleshoo-ting. For further details on how to use the setup software consult the Modbus Interface Manual (MTS Part# 551700), the DDA Interface Manual (MTS Part# 551701), and HART® Interface Manual (MTS Part# 551702).

11. Interface

RefineME® is available with multiple outputs including Modbus, DDA, and HART®. This Operation and Installation Manual includes all of these outputs. Each output has its own specialized Interface Manual that should be consulted for additional information on the specific output. For SIL consult the SIL Safety Manual, MTS Part #551851.

19


Operation Manual

Table 6: Agency approvals

Notified body Protection method Classification Standard

C = CEC I = Instrinsic Safety Class I, Division 1, Groups ABCD T4Class I, Zone 0/1, Ex ia IIC T4Ta = -50°C to 71°C IP65

CAN C22.2 No. 157-92:2012CSA C22.2 No. 1010.1:2004CAN/CSA C22.2 No. 60079-0:2011CAN/CSA C22.2 No. 60079-11:2014CAN/CSA C22.2 No. 60529:2005

F = Explosionproof / Flame proof

Class I, Division 1, Groups BCD T6...T3Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to 71°C IP65

CSA C22.2 No. 0.4-04:R2013CSA C22.2 No. 0.5:R2012CSA C22.2 No. 0-10:R2015CSA C22.2 No. 30:R2012CAN/CSA C22.2 No. 60079-0:2015CAN/CSA C22.2 No. 60079-1:2016CAN/CSA 622.2 No. 60079-26:2016CAN/CSA C22.2 No. 61010.1:2012CSA C22.2 No. 60529:R2010

E = ATEX I = Instrinsic Safety II 1/2 G Ex ia IIC T4Ta = -50°C to 71°C IP65

EN 60079-0:2012EN 60079-11:2012EN 60529:1991 + A1:2000

F = Flame proof II 1/2 G Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to 71°C IP65

EN 60079-0:2012+A11:2013EN 60079-1:2014EN 60079-26:2015EN 60529:1991 + A2:2013

F = NEC I = Instrinsic Safety Class I, Division 1, Groups ABCD T4Class I, Zone 0/1, AEx ia IIC T4Ta = -50°C to 71°C IP65

FM 3600:2011FM 3610:2010FM 3810:2005ANSI/ISA 60079-0:2013ANSI/ISA 60079-11:2014ANSI/IEC 60529:2004

F = Explosionproof / Flame proof

Class I, Division 1, Groups ABCD T6...T3Class I, Division 1, Groups BCD T6...T3Class I, Zone 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C to 71°C IP65

FM 3600:2011FM 3615:2006FM 3810:2005ANSI/ISA 60079-0:2013ANSI/UL 60079-1:2015ANSI/UL 60079-26:2017ANSI/IEC 60529:2004

I = IEC I = Instrinsic Safety Ex ia IIC T4 Ga/Gb Ta = -50°C to 71°C IP65

IEC 60079-0:2011IEC 60079-11:2011

F = Flame proof Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to 71°C IP65

IEC 60079-0:2007-10IEC 60079-1:2007-04IEC 60079-26:2014-10IEC 60529:2013

12. Agency information

12.1 Approvals overviewThe Notified Body is designated in the 13th digit of the model number and the Protection Method is designated in the 14th digit of the model number. These two digits of the model number specify the hazardous area approval that is provided with the selected level transmitter.

20


Operation Manual

12.2 CertificatesDownloadable copies of all certificates are located at www.mtssensors.com and can be downloaded on the product specific landing page. If there is any difficulty in obtaining the certificates from the web contact MTS Technical Support and they will be sent electronically.

12.3 FM (NEC)

12.3.1 Intrinsically Safe

12.3.1.1 Specific Conditions of Safe Use 1. The apparatus enclosure contains aluminum and is considered to constitute a potential risk of ignition by impact or friction. Care must be taken into account during installation and use to prevent impact or friction. ( When installed in a Ga Approval)2. The maximum permitted ambient temperature of the Level Plus Digital/Analog Level Transmitter is 71 °C. To avoid the effects of process temperature and other thermal effects care shall be taken to ensure the surrounding ambient and the ambient inside the transmitter housing does not exceed 71°C3. Some models contain non-metallic enclosure parts, to prevent the risk of electrostatic sparking the nonmetallic surface should only be cleaned with a damp cloth.

12.3.1.2 Labels

Fig. 15: Intrinsically Safe FM label, Modbus or DDA, Single or Dual Cavity Housing

Fig. 16: Intrinsically Safe FM label, HART®, Single or Dual Cavity Housing

Fig. 14: Intrinsically Safe FM label, HART®, NEMA Housing

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES

0.5 0.1




METRIC

FIRST ANGLE 551629-1 B

1 2

DRAWN BY: NJ

A NJ


INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C to +71°C ; IP65when connected in accordance with FM approved installa on drawing # 651543-1

WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS

Model No: Serial No: Date :

MTS Systems CorporationSensors Division3001 Sheldon Dr.Cary, NC 27513

Level Plus Transmitter

USE MTS LOGO ARTWORK

10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE

MTS TO PRINTMODEL NO.SERIAL NO.

DATE CODE.

ENTITY PARAMETERS:SEE PRINT REFERENCE CHART

4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

US

LEVEL

1:1

7570 RELEASE TO PRODUCTION

(ACP) LABEL, LP, IS US - DIGITAL

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT INK.

P/N 551629-1 Rev B

10/24/14

86.30 [3.40]

1.78 [.07]

34.69 [1.37]

1.78 [.07]

69.85 [2.75]

R3.30 [.13]

28.70 [1.13]

15.80 [.62]

12/02/14NJB 7847 IP RATING WAS 66

®

12.3.1.2 Labels (cont‘d.)

651544-1

551641-1

Fig. 13: Intrinsically Safe FM label, Modbus, or DDA, NEMA Housing

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES

0.5 0.1




METRIC


1 2

DRAWN BY: NJ

A NJ


INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C to +71°C ; IP65when connected in accordance with FM approved installa on drawing # 651543-1






10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE


DATE CODE.


4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

US

LEVEL

1:1




P/N 551629-1 Rev B

10/24/14

86.30 [3.40]

1.78 [.07]

34.69 [1.37]

1.78 [.07]

69.85 [2.75]

R3.30 [.13]

28.70 [1.13]

15.80 [.62]

12/02/14NJB 7847 IP RATING WAS 66

®

1

1

2

2

A A

B B

TITLE

SIZE DWG NO. REV



0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC

FIRST ANGLE A 551642- C

1 1

DRAWN BY: NJ


MTS Systems CorporationSensors Division3001 Sheldon Drive, Cary, N.C. 27513

INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS

INSTALL PER DRAWING # 651544-1SUPPLY VOLTAGE: 28 VDC


35.05 [1.38]

"L1"∆ "L2"

17.53 [.69]

7.5 POINT SIZEMTS TO PRINTMODEL NO.

SERIAL NO./DATE CODE

"D1"

4.0 POINT TEXT SIZE(TYP.)

8.97 [.35] 3.47 [.1

(ACP) LABEL, LP, IS US - ANALOG

FM LOGO ARTWORK4.5 POINT TEXT SIZE

R

FM

USE MTS LOGO ARTWORK14.0 POINT SIZE

LEVEL

1:1

APPROVED

�

P/N 551642-X Rev C

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.3. ∆ INDICATES CRITICAL DIMENSIONS.4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES5. MATERIAL: .8 [.03] THICK ALUMINUM6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.

SEE TABLE 1 FOR DASH #.

TABLE 1DASH

# HOUSING "L1" "L2" "D1"

-1 ADALET85.85 [3.38]

69.85 [2.75]

Ø2.35 [.09]x2

-2LIMATHE

RM65 [2.56]

58 [2.28]

Ø 3.05 [.12] x2

C 8256 ADDED "D1" MS 2/22/17B 7847 IP RATING WAS 66 NJ 12/2/14A 7570 RELEASE FOR PRODUCTION NJ 10/24/14


1

1

2

2

A A

B B

TITLE

SIZE DWG NO. REV



0 PLACESMM

1 PLACEMM

ANGLES�� 0.5 � 0.1




METRIC


1 1DRAWN BY: NJ



INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS



35.05 [1.38]

"L1"∆ "L2"

17.53 [.69]

7.5 POINT SIZEMTS TO PRINTMODEL NO.


"D1"


8.97 [.35] 3.47 [.14]



R

FM


LEVEL

1:1

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.3. ∆ INDICATES CRITICAL DIMENSIONS.4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.5. MATERIAL: .8 [0.03] THICK ALUMINUM6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.

APPROVED

�

P/N 551634-X Rev C


TABLE 1DASH

# HOUSING "L1" "L2" "D1"

-1 ADALET85.85[3.38]

69.85 [2.75]

Ø2.35 [.09]x2

-2 LIMATHERM65

[2.56]58

[2.28]Ø 3.05 [.12] x2

C 8256 ADDED "D1" MS 2/22/1766 SAW GNITAR PI7487B NJ 12/2/14

A 7570 RELEASE FOR PRODUCTION NJ 10/24/14ETADYBNOITPIRCSED#OCEVER

21


Operation Manual

12.3.1.3 Installation drawing

Fig. 17: Intrinsically Safe FM installation drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-1

1 2

DR

AWN

BY: M

S

***NO

REV

ISION

S SH

ALL BE M

ADE W

ITHO

UT TH

E NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

).**

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 12/2/14

F

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71 C MS 2/23/15

D 8037 AD

DED

WIRIN

G CH

ART MS 11/3/15

E 8183 ADD

ED CL I Zone 0/1 M

S 8/18/16F 8256 U

PDATED

WIRIN

G CH

ART ON

SHEET 2 M

S 1/30/17

24 VDC

COM

MO

N- >

Rx /Tx+

Rx /Tx-

GRO

UN

D

EARTH G

ROU

ND

(SEE NO

TE 4)

EARTH G

ROU

ND

(SEE NO

TE 4)

Rx/Tx-

Rx/Tx+

GND

+24V

SAFETY BARRIER

SAFETY BARRIER

SAFETY BARRIER

NO

TES

:1.A

LL NA

TION

AL A

ND

LOC

AL C

OD

ES

AN

D R

EGU

LATIO

NS

MU

ST BE

AD

HE

RE

D TO

WH

EN IN

STALLIN

G TH

E LE

VEL SE

NSO

R IN

HA

ZAR

DO

US

EN

VIRO

NM

EN

TS.

SE

AL A

LL CO

ND

UITS W

ITHIN

457 MM

(18"). 2.LO

OP

CAB

LE M

US

T BE 24 AW

G TO

14 AW

G (.511M

M² to 1.6M

M²)

SH

IELDE

D TW

ISTE

D P

AIR

CA

BLE

WITH

SH

IELD. C

ABLE C

AP

ACITA

NC

E M

US

T B

E LE

SS TH

AN

30 pF PER

FOO

T (98 pF PE

R M

). CA

BLE SH

IELD

IS CO

NN

EC

TED

TO SY

STE

M G

RO

UN

D IN

NO

N-H

AZAR

DO

US

AR

EA

. SE

E INS

TALLA

TION

MA

NU

AL FO

R

AD

DITIO

NA

L CAB

LE IN

FOR

MA

TION

. 3.TH

E R

ES

ISTAN

CE

BE

TWEE

N E

ARTH

GR

OU

ND

AND

THE

INTR

INSIC

ALLY

SA

FE GR

OU

ND

MU

ST B

E LESS

THA

N 1 O

HM

. 4.TH

E TR

AN

SD

UC

ER

FRA

ME

SHA

LL BE

GR

OU

ND

ED

TO EA

RTH

GR

OU

ND

DIR

ECTLY

OR

THR

OU

GH

THE

EQU

IPM

EN

T ON

WH

ICH

IT IS M

OU

NTE

D.

5. CO

NTR

OL E

QU

IPM

ENT C

ON

NE

CTE

D TO

AS

SO

CIATE

D A

PPA

RA

TUS

MU

ST

NO

T US

E OR

GE

NE

RATE

MO

RE

THAN

250 VR

MS

OR

VD

C 6.A

SS

OC

IATED

APP

AR

ATUS

MA

NU

FACTU

RE

R'S

INS

TALLA

TION

DR

AW

ING

MU

ST B

E FO

LLOW

ED W

HE

N IN

STA

LLING

THIS

EQU

IPM

EN

T. 7.O

NLY

US

E NE

C (e.g FM

) APP

RO

VE

D B

AR

RIE

RS

. 8.E

NTITY P

AR

AME

TER

S: S

UPP

LY: R

x/Tx-: Rx/Tx+:

Ui = 28V

DC

Ui= 8.6V

Ui= 8.6V

Ii = 100mA

Ii = 10mA

Ii = 10mA

C

i = 0 µF Ci = 0 µF C

i = 0 µF Li = 0 µH

Li = 0 µH Li = 0 µH

Pi = 0.7 W

Pi= 0.0215 W

P i= 0.0215 W

9.THE

ENTITY

CO

NC

EPT A

LLOW

S INTE

RC

ON

NE

CTIO

N O

F INTR

INS

ICA

LLY S

AFE

APP

AR

ATU

S W

ITH AS

SO

CIA

TED A

PPA

RA

TUS

WH

EN

THE

FOLLO

WIN

G IS

TRU

E:

V

max or U

i ≥ Voc, V

t or Uo;

Imax or Ii ≥ Isc, It or Io;

Pm

ax or Pi ≥ Po;

Ca ≥ C

i + Ccable;

La ≥ Li + Lcable. 10.D

UAL-C

AVITY

EN

CLO

SU

RE

S: C

US

TOM

ER

CO

NN

EC

TION

S WILL BE

MA

DE AT TE

RM

INA

L BLO

CK

ON

PO

WE

R SID

E O

F HO

US

ING

(NO

T TO TE

RM

INA

L BLO

CK

ON

INTER

CO

NN

EC

T BO

ARD

). 11.IN

STA

LLATIO

N SH

OU

LD B

E IN A

CC

OR

DAN

CE

WITH

ANS

I/ISA

RP

12.06.01 "INS

TALLA

TION

OF

INTR

INS

ICA

LLY SA

FE S

YSTE

MS

FOR

HA

ZAR

DO

US

(CLA

SS

IFIED

) LOC

ATIO

NS

" A

ND

THE

NA

TION

AL E

LEC

TRIC

AL C

OD

E (AN

SI/N

FPA

70). 12.TH

E M

AX

IMU

M PE

RM

ITTED

AM

BIE

NT TE

MP

ER

ATU

RE

OF TH

E LE

VEL P

LUS

DIG

ITAL/A

NA

LOG

LE

VE

L TRAN

SM

ITTER

IS 71 °C

. TO A

VO

ID TH

E E

FFEC

TS O

F PR

OC

ESS

TEM

PE

RA

TUR

E A

ND

O

THE

R TH

ER

MAL EFFE

CTS C

AR

E S

HALL B

E TAK

EN

TO EN

SU

RE

THE

SU

RR

OU

ND

ING

AM

BIEN

T A

ND

THE

AMBIE

NT IN

SID

E TH

E TR

ANS

MITTE

R H

OU

SING

DO

ES

NO

T EX

CE

ED

71°C 13.C

AU

TION

: FLEX

IBLE

GA

UG

ES

HA

VE

A MIN

IMU

M B

EN

D D

IAM

ETER

OF 406M

M(16")

14.WA

RN

ING

: THE

APP

AR

ATU

S EN

CLO

SU

RE

CO

NTA

INS A

LUM

INU

M A

ND

IS CO

NS

IDE

RED

TO C

ON

STITU

TE A

PO

TEN

TIAL R

ISK O

F IGN

ITION

BY IM

PAC

T OR

FRIC

TION

. CAR

E M

UST B

E TA

KEN

IN

TO A

CC

OU

NT D

UR

ING

INS

TALLA

TION

AN

D U

SE

TO P

REV

EN

T IMP

ACT O

R FR

ICTIO

N15.W

AR

NIN

G: S

UBS

TITUTIO

N O

F CO

MP

ON

EN

TS M

AY

IMP

AIR

INTR

INS

IC S

AFE

TY.

16.WA

RN

ING

: TO PR

EV

ENT IG

NITIO

N O

F FLAM

MA

BLE

OR

CO

MB

USTIB

LE A

TMO

SP

HER

ES

, D

ISC

ON

NE

CT P

OW

ER

BEFO

RE

SER

VIC

ING

17.W

AR

NIN

G: TH

E EQ

UIP

ME

NT C

ON

TAIN

S NO

N-M

ETALLIC

EN

CLO

SU

RE

PAR

TS, TO P

RE

VE

NT

THE

RIS

K O

F ELE

CTR

OS

TATIC

SPA

RKIN

G. TH

E N

ON

-ME

TALLIC

SU

RFAC

E S

HO

ULD

ON

LY

BE

CLEA

NE

D W

ITH A D

AM

P C

LOTH

.

NO

N H

AZARDO

US LO

CATION

HAZARD

OU

S LOCATIO

N

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERM

INAL

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTR

INSICALLY SAFE FO

R U

S

LEVEL

FM

APPROVED US

N/A

INTRIN

SICALLY SAFECL. I, D

IV. 1, GR. ABCD

CL. I Zone 0/1 AEx ia IIC T4 Ta =

-50 to 71°C ; IP65

22


Operation Manual

12.3.1.3 Installation drawing (cont.)

Fig. 18: Intrinsically Safe FM installation drawing, Modbus and DDA, Page 2

DETAIL A

SCALE 1.60 : 1

DETAIL C

SCALE 3 : 1

DETAIL D

SCALE 1.2

DETAIL E

SCALE 1 : 1

A

C

D

E

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-1

2 2

DR

AWN

BY: M

S

***NO

REV

ISION

S SH

ALL BE M

ADE W

ITHO

UT TH

E NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

).**

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 12/2/14

F

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71 C MS 2/23/15

D 8037 AD

DED

WIRIN

G CH

ART MS 11/3/15

E 8183 ADD

ED CL I Zone 0/1 M

S 8/18/16F 8256 U

PDATED

WIRIN

G CH

ART ON

SHEET 2 M

S 1/30/17

+24V GNDEARTHTX/RX+TX/RX-

GND+24V

TX/RX-TX/RX+EARTH

GND

+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

457 MM

(18") OF H

OU

SING

.

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTRIN

SICALLY SAFE FOR U

S

+24V GND EARTH Tx/Rx+ Tx/Rx-

WIRE CO

LOR

SIGN

ALRED

24 V PWR

BLACK 0 V PW

RBLU

EN

/AW

HITE

RX TX +G

REENRX TX -

DRAIN

WIRE

EARTH G

ROU

ND

WIRIN

G CH

ART (FOR N

EMA G

AUG

E)

PIN #

SIGN

ALPIN

124 V PW

RPIN

20 V PW

RPIN

3N

/APIN

4RX TX+

PIN 5

RX TX-PIN

6EARTH

GRO

UN

D

PIN W

IRING

CHART (FO

R NEM

A GAU

GE)

LEVEL

23


Operation Manual


Fig. 19: Intrinsically Safe FM installation drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651544-1LEVEL

1 2

DR

AWN

BY: M

S1:1

***NO

RE

VISIO

NS SH

ALL BE M

AD

E W

ITHO

UT N

OTIFIC

ATION

TO AP

PRO

VAL A

GEN

CY

(S)***

B 7847 UP

DA

TED IP R

ATING

FOR

HO

USIN

G TYPE

MS 12/2/14

C 7898 U

PDATE

D TEM

PER

ATUR

E O

N N

OTE 12 TO

71°C M

S 2/23/15D

8037 ADD

ED W

IRIN

G C

HA

RT M

S 11/3/15E 8183 AD

DED

CL I Zone 0/1 MS 8/18/16

F 8256 UPD

ATED W

IRING

CHAR

T ON

SHEET 2 M

S 1/30/17

NO

N H

AZAR

DO

US LO

CATIO

NH

AZAR

DO

US

LOC

ATION

NO

TES:

1. ALL N

ATION

AL AND

LOC

AL CO

DE

S A

ND

RE

GU

LATION

S MU

ST B

E AD

HER

ED TO

WH

EN

INS

TALLING

THE

MTS LP S

ENSO

R IN

HAZA

RD

OU

S EN

VIR

ON

MEN

TS.

SEA

L ALL CO

ND

UITS

WITH

IN 457 M

M (18").

2. LOO

P C

ABLE M

US

T BE 24 A

WG

TO 14 A

WG

(.511MM

² to 1.6MM

²) S

HIE

LDED

TWIS

TED PA

IR C

AB

LE W

ITH SH

IELD. C

ABLE

CA

PAC

ITAN

CE M

US

T B

E LESS

THA

N 30 pF PE

R FO

OT (98 pF P

ER m

). CAB

LE SH

IELD

IS C

ON

NEC

TED

TO S

YSTE

M G

RO

UN

D IN

NO

N-H

AZA

RD

OU

S AR

EA

. SEE

INS

TALLA

TION

MA

NU

AL FO

R

AD

DITIO

NA

L CAB

LE IN

FOR

MA

TION

. 3. TH

E RES

ISTAN

CE

BE

TWE

EN E

ARTH

GR

OU

ND

AND

THE IN

TRIN

SICA

LLY SA

FE GR

OU

ND

MU

ST BE

LESS

THA

N 1 O

HM

. 4. TH

E TR

AN

SD

UC

ER

FRA

ME

SHALL BE

GR

OU

ND

ED TO

EA

RTH

GR

OU

ND

DIR

EC

TLY O

R TH

RO

UG

H TH

E EQ

UIP

ME

NT O

N W

HIC

H IT IS M

OU

NTED

. 5. C

ON

TRO

L EQ

UIPM

EN

T CO

NN

EC

TED

TO AS

SO

CIA

TED

AP

PAR

ATUS M

UST

NO

T US

E O

R G

ENE

RA

TE MO

RE

THA

N 250 VR

MS

OR

VD

C.

6. AS

SOC

IATE

D A

PPAR

ATU

S MAN

UFAC

TUR

ER

'S INS

TALLATIO

N D

RA

WIN

G M

UST

BE

FOLLO

WED

WH

EN

INSTALLIN

G TH

IS EQ

UIP

ME

NT

7. ON

LY U

SE N

EC

(e.g FM) AP

PRO

VE

D B

ARR

IER

S.

8. AP

PRO

VED

LOO

P SE

PAR

ATION

METH

OD

S: *R

UN

LOO

PS IN

SEP

ARA

TE C

ABLE

S *R

UN

LOO

PS IN

SEP

ARA

TE G

RO

UN

DED

SHIE

LDS

9. EN

TITY PA

RAM

ETERS E

ACH

LOO

P:

Ui = 28 VD

C Ii = 120 m

A C

i = 0 µF Li = 5 µH Pi = 840 m

W 10. D

UA

L-CAV

ITY EN

CLO

SU

RE

S: C

US

TOM

ER

CO

NN

EC

TION

S WILL B

E M

ADE

AT TE

RM

INAL BLO

CK

ON

PO

WER

SIDE

OF H

OU

SING

(NO

T TO TE

RM

INA

L BLO

CK O

N IN

TERC

ON

NEC

T BO

AR

D)

11 INSTALLATIO

N S

HO

ULD

BE IN

ACC

OR

DAN

CE W

ITH A

NS

I/ISA R

P12.06.01 "INSTALLATIO

N O

F IN

TRIN

SICALLY S

AFE SYS

TEMS FO

R H

AZA

RD

OU

S (CLA

SSIFIE

D) LO

CA

TION

S"

AN

D TH

E NATIO

NAL ELE

CTR

ICA

L CO

DE

(AN

SI/N

FPA 70).

12.THE

MA

XIMU

M P

ERM

ITTED

AM

BIEN

T TEMPE

RATU

RE O

F THE

LEVE

L PLU

S D

IGITAL/A

NA

LOG

LEV

EL TRA

NS

MITTE

R IS 71 °C

. TO A

VOID

THE

EFFE

CTS O

F PR

OC

ESS

TEM

PE

RA

TUR

E AN

D

OTH

ER TH

ERM

AL E

FFECTS C

ARE S

HA

LL BE TA

KEN

TO E

NSU

RE

THE S

UR

RO

UN

DIN

G A

MB

IEN

T A

ND

THE

AMBIE

NT IN

SID

E TH

E TRA

NS

MITTE

R H

OU

SING

DO

ES N

OT E

XCE

ED 71°C

13.CAU

TION

: FLEXIB

LE G

AU

GES

HA

VE A

MIN

IMU

M B

END

RAD

IUS

OF 406M

M (16")

14. WA

RN

ING

: THE

APP

ARATU

S EN

CLO

SUR

E C

ON

TAINS A

LUM

INU

M A

ND

IS CO

NSID

ERED

TO C

ON

STITUTE

A PO

TENTIA

L RISK

OF IG

NITIO

N B

Y IM

PAC

T OR

FRIC

TION

. CAR

E MU

ST B

E TAKEN

IN

TO A

CC

OU

NT D

UR

ING

INS

TALLATIO

N A

ND

US

E TO P

RE

VEN

T IMP

ACT O

R FR

ICTIO

N 15.W

ARN

ING

: SUBS

TITUTIO

N O

F CO

MP

ON

ENTS

MA

Y IMP

AIR IN

TRIN

SIC

SAFETY

. 16.W

ARN

ING

: TO P

REV

ENT IG

NITIO

N O

F FLAM

MAB

LE OR

CO

MB

US

TIBLE A

TMO

SPH

ERES

. D

ISC

ON

NEC

T PO

WER

BEFO

RE S

ERVIC

ING

. 17.W

AR

NIN

G: TH

E EQ

UIP

MEN

T CO

NTA

INS

NO

N-M

ETA

LLIC EN

CLO

SUR

E P

AR

TS, TO

PRE

VEN

T TH

E R

ISK O

F ELE

CTR

OS

TATIC

SPA

RK

ING

. THE

NO

N-M

ETALLIC

SUR

FAC

E S

HO

ULD

ON

LY B

E C

LEA

NE

D W

ITH A

DA

MP

CLO

TH.

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

24 VD

C

CO

NTR

OL

INP

UT 1

CO

NTR

OL

INP

UT 2

APPR

OVE

D SAFETY

BAR

RIER

APPR

OVED

SAFE

TY BA

RR

IER

LOO

P VO

LTAGE

SHIE

LD

SH

IELD

LOO

P 1+

LOO

P 1-

LOO

P 2+

LOO

P 2-

FM

APPROVED US

US

(ACP) INSTALLATIN

DW

G LP AN

ALOG

INTR

INSICALLY SAFE FO

R U

S

SIN

GLE

OR

DU

AL C

AVITY

NEM

A H

OU

SIN

G

F

INTRIN


IV. 1, GR. ABCD

CL. I Zone 0/1 AEx ia IIC T4 Ta =

-50 to 71°C ; IP65

EARTH

GR

OU

ND

(SEE N

OTE

4)

EAR

TH G

RO

UN

D(SEE

NO

TE 4)

24


Operation Manual


Fig. 20: Intrinsically Safe FM installation drawing, HART®, Page 2

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

DETAIL H

SCALE 1 : 1

D

E

F

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651544-1LEVEL

2 2

DR

AWN

BY: M

S1:1

***NO

RE

VISIO

NS SH

ALL BE M

AD

E W

ITHO

UT N

OTIFIC

ATION

TO AP

PRO

VAL A

GEN

CY

(S)***

B 7847 UP

DA

TED IP R

ATING

FOR

HO

USIN

G TYPE

MS 12/2/14

C 7898 U

PDATE

D TEM

PER

ATUR

E O

N N

OTE 12 TO

71°C M

S 2/23/15D

8037 ADD

ED W

IRIN

G C

HA

RT M

S 11/3/15E 8183 AD

DED

CL I Zone 0/1 MS 8/18/16

F 8256 UPD

ATED W

IRING

CHAR

T ON

SHEET 2 M

S 1/30/17

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER

SHO

ULD

CO

NN

ECT TH

E OU

TSID

E GR

OU

ND

LUG

TO TH

E SAFE

TY EAR

THIN

G G

RO

UN

D SYS

TEM W

ARN

ING

: C

ON

DU

IT SEALS R

EQ

UIR

ED

WITH

IN 457 M

M (18") O

F HO

USIN

G.

FIGU

RE 2

DU

AL CAV

ITY HO

USIN

G

LOOP 1+ LOOP 1- EARTH LOOP 2+ LOOP 2-

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING


(ACP

) INS

TALLATION

DW

G LP A

NALG

O

INTR

INS

ICALLY SAFE ATEX

/IECE


F

PIN #

SIGN

ALPIN

1LO

OP 1-

PIN 2

LOO

P 1+PIN

3LO

OP 2-

PIN 4

LOO

P 2+PIN

5N

/APIN

6EARTH

GRO

UN

D

WIRE CO

LOR

SIGN

ALRED

LOO

P 1+BLACK

LOO

P 1-BLU

ELO

OP 2-

WH

ITELO

OP 2+

GREEN

N/A

DRAIN

WIRE

EARTH G

ROU

ND

PIN W

IRING

CHART (FO

R NEM

A GAU

GE)

WIRIN

G CH

ART(FOR N

EMA G

AUG

E)

25


Operation Manual

12.3.2 Explosionproof / Flame Proof

12.3.2.1 Specific Conditions of Safe Use

1. Warning: The equipment contains non-metallic enclosure and process parts, to prevent the risk of electrostatic sparking, the non-metallic surface should only be cleaned with a damp cloth. Painted surface of the equipment may store electrostatic charge and become a source of ignition in applications with a low relative humidity <~30% relative humidity where the painted surface is relatively free of surface contamination such as dirt, dust or oil. Cleaning of the painted surface should only be done with a damp cloth.2. Cables shall be rated > 5°C above maximum ambient temperature.3. To maintain the ingress protection rating of IP65, Teflon tape (3 wraps) or pipe dope shall be used. Refer to Installation Instructions.4. The equipment can be installed in the boundary wall between a Zone 0 area and the less hazardous area, Zone 1. In this configuration, the process connection is installed in Zone 0, while the transmitter housing is installed in Zone 1. Refer to installation instructions.5. Flexible gauges have a minimum bend radius of 381 mm (15 inches).6. Flamepaths not for repair.7. The applicable temperature class, ambient temperature range and process temperature range of the equipment is as follows:

T3 with Process Temperature range -40°C to +150°CT4 with Process Temperature range -40°C to +135°CT5 with Process Temperature range -40°C to +100°CT6 with Process Temperature range -40°C to +85°CAmbient Temperature Range is -40°C≤Ta≤71°C

8. When mounting on a MLG (magnetic level gauge) make sure the electronic head and pressure barrier have a minimum spacing of 5 inches. See Installation Manual for detail.

12.3.2.2 Labels

12.3.2.2 Labels (cont.)

Fig. 22: Explosionproof, FM label, Modbus or DDA, Housing Option D, E

Fig. 21: Explosionproof, FM label, Modbus or DDA Housing Option G, H, or L

Fig. 24: Explosionproof, FM label, HART®, Housing Option D, E

Fig. 23: Explosionproof, FM label, HART®, Housing Option G, H, or L

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC

FIRST ANGLE A 551474- A

1 1

DRAWN BY: MS

***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION TO APPROVAL AGENCY(S).***A MS 7/28/16

Level Plus Transmitter�


FM16US0242X

EXPLOSION PROOF FOR CL. I, DIV. 1, GR. CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40

ABCD T6...T3

°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: RS485 WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE

INSTALL PER # 651552-1MAX. PRESSURE 1000 PSI (RIGID SENSOR)

MAX. PRESSURE 435 PSI (FLEX SENSOR)

7957 RELEASE FOR PRODUCTION

(ACP) LABEL, LP, XP US - DIGITAL

FM

LEVEL

1:1

APPROVED

P/N 551474-2 Rev A

R

!

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY: MS




FM16US0242X

EXPLOSION PROOF FOR CL. I, DIV. 1, GR BCD T6...T3.

(B, C, D)

CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: RS485 WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE

INSTALL PER # 651552-1MAX. PRESSURE 1000 PSI (RIGID SENSOR)

MAX. PRESSURE 435 PSI (FLEX SENSOR)


(ACP) LABEL, LP, XP US - DIGITAL

FM

LEVEL

1:1

APPROVED

P/N 551474-1 Rev A

R

!

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY: MS


Level Plus TransmitterFM16US0242X

�


EXPLOSION PROOF FOR CL. I, DIV. 1, GR. ABCD T6...T3

(B, C, D)

CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: 4-20mA WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE

INSTALL PER # 651553-1MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)


(ACP) LABEL, LP, XP US - ANALOG

FM

LEVEL

1:1

APPROVED

P/N 551495-2 Rev A

R

!

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY: MS


Level Plus TransmitterFM16US0242X

�


EXPLOSION PROOF FOR CL. I, DIV. 1, GR.

(A, B, C, D)

BCD T6...T3CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: 4-20mA WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE

INSTALL PER # 651553-1MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)


(ACP) LABEL, LP, XP US - ANALOG

FM

LEVEL

1:1

APPROVED

P/N 551495-1 Rev A

R

!

26


Operation Manual

12.3.2.3 Installation Drawing

Fig. 25: Explosionproof, FM Installation Drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651553-1A

LEVEL1

2

DR

AWN

BY: M

S1:1

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

)***A

7957 RE

LEAS

E TO PR

OD

UC

TION

MS 10/22/15

EARTH G

ROU

ND

Rx /Tx-

Rx /Tx+

EARTH G

ROU

ND

COM

MO

N-

24 VDC

ZON

E 1

ZON

E 0

SEE NO

TE 8

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

FM

APPROVED US

(ACP) INSTALLATIN

DW

G LP AN

ALOG

EXPLOSIO

N PRO

OF U

S

SING

LE OR

DU

AL CA

VITY

FM U

S- FM16U

S0242XEXPLO

SION

PROO

FCL. I, D

IV. 1, GR. ABCD

T6...T3CL. I, D

IV. 1, GR. BCD

T6...T3CL. 1, ZN

. 0/1, AEx db IIB+H

2 T6...T3 Ga/G

bTa =

-40°C to +71°C ; IP65

HAZARD

OU

S LOCATIO

NN

ON

HAZARD

OU

S LOCATIO

N

CO

ND

UIT SEAL

CO

ND

UIT

SEE NO

TE 1

CO

ND

UIT SEAL

5" [127mm

] Minim

um

NO

TES:

1.ALL NATIO

NA

L AN

D LO

CAL C

OD

ES AN

D R

EGU

LATIO

NS M

UST B

E AD

HE

RED

TO W

HE

N IN

STA

LLING

THE

LEVE

L SEN

SO

R IN

HA

ZARD

OU

S EN

VIRO

NM

EN

TS. FO

R ZO

NE IN

STALLA

TION

S, A

SEAL SH

ALL BE

INSTA

LLED

WITH

IN 50m

m O

F THE

EN

CLO

SU

RE. FO

R D

IVISIO

N IN

STALLATIO

NS, A S

EAL S

HALL B

E INS

TALLED W

ITHIN

18 INC

HES

OF TH

E EN

CLO

SUR

E.

2.DU

AL-CA

VITY EN

CLO

SUR

ES:

CU

STOM

ER

CO

NN

EC

TION

S W

ILL BE M

ADE

AT TE

RM

INAL B

LOC

K O

N PO

WE

R S

IDE

OF H

OU

SIN

G (N

OT TO

TERM

INA

L BLOC

K ON

INTE

RC

ON

NEC

T BO

ARD

). SEE

FIGU

RE 2 O

N PA

GE 2

3. CAU

TION

: FLEX

IBLE G

AUG

ES H

AVE

A M

INIM

UM

BEN

D R

ADIU

S O

F 381mm

(15")4.W

AR

NIN

G: TO

PRE

VEN

T IGN

ITION

OF FLAM

MAB

LE O

R C

OM

BUS

TIBLE ATM

OSP

HER

ES

, D

ISCO

NN

EC

T PO

WER

BEFO

RE

SER

VIC

ING

5.W

AR

NIN

G: TH

E EQU

IPMEN

T CO

NTA

INS N

ON

-ME

TALLIC E

NC

LOSU

RE A

ND

PR

OC

ESS P

ARTS

, TO PR

EVE

NT

THE R

ISK

OF E

LEC

TRO

STATIC

SPA

RK

ING

. THE N

ON

-ME

TALLIC S

UR

FACE

AND

PRO

CE

SS PA

RTS S

HO

ULD

ON

LY BE

CLE

ANE

D W

ITH A D

AM

P C

LOTH

. PAINTED

SURFACE O

F THE EQ

UIPM

ENT M

AY STORE ELECTRO

STATIC CHAR

GE

AND

BECOM

E A SOU

RCE OF IG

NITIO

N IN

APPLICATION

S WITH

A LOW

RELATIVE HU

MID

ITY <~

30% RELATIVE

HU

MID

ITY WH

ERE THE PAIN

TED SU

RFACE IS RELATIVELY FREE OF SU

RFACE CO

NTAM

INATIO

N SU

CH AS D

IRT, DU

ST OR O

IL. CLEANIN

G O

F THE PAIN

TED SU

RFACE SHO

ULD

ON

LY BE DO

NE

WITH

A DAM

P CLOTH

.6. C

ABLE

S SH

ALL BE R

ATED

> 5C A

BOVE

MA

XIMU

M A

MB

IENT TE

MP

ERA

TUR

E. 7. TO

MAIN

TAIN

THE IN

GR

ESS P

RO

TECTIO

N R

ATIN

G O

F IP65, TE

FLON

TAPE (3 W

RA

PS) O

R PIP

E DO

PE S

HALL

BE U

SED

. REFE

R TO

INSTALLA

TION

INSTR

UC

TION

S.

8. THE E

QU

IPMEN

T CA

N BE

INS

TALLED IN

THE B

OU

ND

ARY W

ALL BETW

EEN

A ZON

E 0 ARE

A AN

D TH

E LE

SS H

AZAR

DO

US A

RE

A, ZON

E 1. IN TH

IS C

ON

FIGU

RATIO

N, TH

E P

RO

CE

SS C

ON

NE

CTIO

N IS IN

STALLE

D

IN A

ZON

E 0 A

RE

A, WH

ILE TH

E TRA

NS

MITTER

HO

US

ING

IS IN

STALLE

D IN

A ZO

NE 1 AR

EA.

9. THE A

PPLIC

ABLE TE

MPE

RA

TUR

E CLAS

S OF TH

E EQU

IPM

ENT, AM

BIE

NT TE

MP

ERA

TUR

E R

ANG

E,

AND

MAX

IMU

M PR

OC

ESS

TEMPE

RATU

RE

OF TH

E EQ

UIPM

ENT IS

AS FO

LLOW

S;

T3 WITH

PRO

CE

SS TEM

PE

RATU

RE

RAN

GE

OF -40°C

to +150°C T4 W

ITH PR

OC

ESS

TEMP

ER

ATUR

E R

ANG

E O

F -40°C to +135°C

T5 WITH

PRO

CE

SS TEM

PE

RATU

RE

RAN

GE

OF -40°C

to +100°C T6 W

ITH PR

OC

ESS

TEMP

ER

ATUR

E R

ANG

E O

F -40°C to +85°C

AMBIE

NT TEM

PER

ATUR

E R

ANG

E -40°C Ta+71°C

10. WH

EN M

OU

NTIN

G O

N A

MA

GN

ETIC LEV

EL GA

UG

E MAK

E SU

RE

THE E

LEC

TRO

NIC

HEA

D A

ND

PRES

SUR

E

BAR

RIE

R H

AVE

A MIN

IMU

M SP

ACIN

G O

F 5 INC

HES

. SEE

INS

TALLATION

MA

NU

AL FO

R D

ETAIL

11. FLAM

EPATH

S A

RE N

OT FO

R R

EPAIR

27


Operation Manual

12.3.2.3 Installation Drawing (cont.)

Fig. 26: Explosionproof, FM Installation Drawing, Modbus and DDA, Page 2

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

D

E

F

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651553-1A

LEVEL2

2

DR

AWN

BY: M

S1:1

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

)***A

7957 RE

LEAS

E TO PR

OD

UC

TION

MS 10/22/15

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER

SHO

ULD

CO

NN

ECT TH

E OU

TSID

E GR

OU

ND

LUG

TO TH

E SAFETY EAR

THIN

G G

RO

UN

D SYS

TEM W

ARN

ING

: FO

R ZO

NE IN

STALLATION

S, A S

EAL SHALL BE

INS

TALLED W

ITHIN

50mm

OF TH

E E

NC

LOSU

RE

. FOR

DIVISIO

N IN

STALLATIO

NS, A

SEAL S

HA

LL BE INSTA

LLED

WITH

IN 18 IN

CH

ES OF TH

E EN

CLO

SUR

E.

FIGU

RE 2

DU

AL CAV

ITY HO

USIN

G


FIGU

RE 1

SING

LE CAVITY H

OU

SING

(AC

P) INSTALLA

TION

DW

G LP

ANALO

G

INTR

INSIC

ALLY SA

FE US


28


Operation Manual

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651552-1A

1

2 D

RAW

N BY:

MS

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T THE

NO

TIFICA

TION

TO A

PPRO

VAL AG

EN

CY(S).***

AM

S6/22/16

RELEASE TO PRO

DU

CTION

24 VDC

COM

MO

N-

Rx /Tx+

Rx /Tx-

EARTH G

ROU

ND

EARTH G

ROU

ND

ZON

E 1

ZON

E 0

SEE NO

TE 8

NO

N H

AZARDO

US LO

CATION

HAZARD

OU

S LOCATIO

N

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERM

INAL

(ACP) INSTALLATIO

N D

WG

LP DIG

ITAL EXPLO

SION

PROO

F US

7957

LEVEL

FM

APPROVED

N/A

EXPLOSIO

N PRO

OF

CL. I, DIV. 1, G

R. ABCD T6...T3

CL. I, DIV. 1, G

R. BCD T6...T3

CL. 1, ZN. 0/1, AEx db IIB+

H2 T6...T3 G

a/Gb

Ta = -40°C to +

71°C ; IP65

NO

TES:1.A

LL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE LEVEL SEN

SOR

IN H

AZAR

DO

US EN

VIRO

NM

ENTS.

FOR

ZON

E INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 50m

m O

F THE

ENC

LOSU

RE

. FOR

DIVISIO

N IN

STALLA TION

S, A SEAL SHALL BE IN

STALLED W

ITHIN

18 INC

HES O

F THE EN

CLO

SUR

E.2.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

US

ING

(NO

T TO TER

MIN

AL BLO

CK O

N IN

TERC

ON

NEC

T BO

ARD

). SEE FIGU

RE 2 O

N PAG

E 23. C

AUTIO

N: FLEX

IBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381mm

(15")4.W

ARN

ING

: TO PR

EVENT IG

NITIO

N O

F FLAMM

ABLE OR

CO

MBU

STIBLE ATMO

SPHER

ES, D

ISCO

N NEC

T POW

ER BE

FOR

E SERVIC

ING

5.W

ARN

ING

: THE EQ

UIPM

ENT C

ON

TAINS

NO

N-M

ETALLIC E

NC

LOSU

RE

AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FAC

E AND

PRO

CES

S PARTS SH

OU

LD O

NLY

BE CLEAN

ED W

ITH A

DAM

P CLO

TH. PAIN

TED SU

RFACE OF TH

E EQU

IPMEN

T MAY STO

RE ELECTROSTATIC CH

ARG

E AN

D BECO

ME A SO

URCE O

F IGN

ITION

IN APPLICATIO

NS W

ITH A LO

W RELATIVE H

UM

IDITY <

~30%

RELATIVE H

UM

IDITY W

HERE TH

E PAINTED

SURFACE IS R

ELATIVELY FREE OF SU

RFACE CON

TAMIN

ATION

SUCH

AS DIRT, D

UST O

R OIL. CLEAN

ING

OF TH

E PAINTED

SURFACE SH

OU

LD O

NLY BE D

ON

E W

ITH A D

AMP CLO

TH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATU

RE.

7. TO M

AINTAIN

THE IN

GR

ESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLA

TION

INSTR

UC

TION

S.8. TH

E EQ

UIP

ME

NT C

AN BE IN

STALLED IN

THE BO

UN

DAR

Y WALL BETW

EEN A ZO

NE 0 A

REA AN

D TH

E LESS H

AZARD

OU

S AREA, ZO

NE 1. IN

THIS C

ON

FIGU

RATIO

N, TH

E PRO

CE

SS CO

NN

ECTIO

N IS IN

STALLED

IN

A ZON

E 0 AREA, W

HILE TH

E TR

ANS

MITTER

HO

US

ING

IS INSTALLED

IN A ZO

NE 1 AR

EA. 9. TH

E APPLIC

ABLE TEM

PERATU

RE C

LASS O

F THE

EQ

UIP

MEN

T, AM

BIEN

T TEMPER

ATUR

E RA

NG

E,

AND

MAX

IMU

M PR

OC

ESS TEM

PERATU

RE O

F THE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH P

RO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH P

RO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +135°C T5 W

ITH P

RO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH P

RO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +85°C AM

BIENT TEM

PERATU

RE

RAN

GE -40°C Ta+71°C

10. WH

EN M

OU

NTIN

G O

N A M

AG

NETIC

LEVEL G

AU

GE M

AKE S

UR

E TH

E ELEC

TRO

NIC

HEA

D AN

D PR

ESS

UR

E

BAR

RIE

R H

AVE

A MIN

IMU

M SP

AC

ING

OF 5 IN

CH

ES. S

EE IN

STALLATIO

N M

AN

UAL FO

R D

ETAIL

11. FLAM

EPA

THS A

RE N

OT FO

R R

EPA

IR

FM U

S- FM16U

S0242X

CON

DU

IT SEALCON

DU

IT

SEE NO

TE 1

CON

DU

IT SEAL


Fig. 27: Explosionproof, FM Installation Drawing, HART®, Page 1

29


Operation Manual


Fig. 28: Explosionproof, FM Installation Drawing, HART®, Page 2

DETAIL F

SCALE 1.60 : 1

DETAIL G

SCALE 3 : 1

DETAIL H

SCALE 1.2

F

G

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RATIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-1A

2

2 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***A

MS

10/24/14RELEASE TO

PROD

UCTIO

N


GND

+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: FO

R ZO

NE IN

STALLATION


STALLED W

ITHIN

50mm

OF TH

EEN

CLO

SUR

E. FOR

DIVISIO

N IN

STALLATION


STALLED W

ITHIN

18 INC

HES O

F THE EN

CLO

SUR

E.

(ACP) INSTALLATIO

N D

WG

LP DIG

ITAL EXPLO

SION

PROO

F U.S.A


7957

30


Operation Manual

12.4 FMC (CEC)


12.4.1.1 Specific conditions of safe use

1. The apparatus enclosure contains aluminum and is considered to constitute a potential risk of ignition by impact or friction. Care must be taken into account during installation and use to prevent impact or friction. ( When installed in a Ga Approval)2. The maximum permitted ambient temperature of the Level Plus® Digital/Analog Level Transmitter is 71 °C. To avoid the effects of process temperature and other thermal effects care shall be taken to ensure the surrounding ambient and the ambient inside the transmitter housing does not exceed 71°C.3. Some models contain non-metallic enclosure parts, to prevent the risk of electrostatic sparking the nonmetallic surface should only be cleaned with a damp cloth.

12.4.1.2 Labels

1

1

2

2

A A

B B

ECO # DESCRIPTION

C 8037 ADDED FRENCH TRANSLATION DR 10/12/15


(ACP) LABEL, LP, IS CANADA-ANALOGMTS SYSTEMS CORPORATIONSENSORS DIVISION3001 SHELDON DRIVE, CARY, NC 27513

B 7847 IP RATING WAS 66 NJ 12/02/14

PRODUCT LINE

FIRST ANGLE

mANGLES��

SIZE

LEVEL1:1 METRICSCALE:

DRAWN BY:

DWG NO.

1

DATEBY

2OF

D551641-2REV

SHEET


1 PLACEMM

� 0.1

0 PLACESMM

� 0.5

THE INFORMATION AND DESIGN(S) DISCLOSEDHEREIN ARE THE PROPERTY OF MTS SYSTEMSCORPORATION AND MAY NOT BE USED,REPRODUCED OR DISCLOSED IN ANY FORMEXCEPT AS GRANTED IN WRITING BY MTSSYSTEMS CORPORATION. THIS RESTRICTIONEXCLUDES INFORMATION THAT IS IN THE PUBLIC DOMAIN OR WAS LEGITIMATELY IN THEPRIOR POSSESSION OF THE RECIPIENT.

PROPRIETARY DATA TOLERANCESUNLESS OTHERWISE SPECIFIED TITLE

REV

D 8183 ADDED CL. I Zone 0/1 MS 8/8/16

WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGSAVERTISSEMENT : se référer au schéma d'installation à la prudence / AVERTISSEMENTS

INTRINSICALLY SAFECL. I, Div. 1, GR. ABCD CL.I Zone 0/1 Ex ia IIC T4 Ta = -50°C to +71°C ; IP65

when connected in accordance with FM approvedinstallation drawing # 651544-2 lorsqu'il est connecté en conformité avec FM approuvéedessin d'installation # 651544-2


Model No: Modèle No:

Serial No:Numéro de série:

Date:

R

USE MTS LOGOARTWORK

10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE

MTS TO PRINTMODEL NO.SERIAL NO.DATE CODE


4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

C


P/N: 551641-2 Rev D

NOTES:

1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.

2. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.

3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT INK.

1.78 [.07]

1.78 [.07]

28.70 [1.13]

15.80 [.62]

34.69 [1.37]

86.30 [3.40]

69.85 [2.75]

R3.30 [.13]

®

Fig. 30: Intrinsically Safe FMC label, HART®, NEMA Housing

Fig. 31: Intrinsically Safe FMC label, Modbus and DDA, Single and Dual Cavity Housing

Fig. 32: Intrinsically Safe FMC label, HART®, Single and Dual Cavity Housing

651544-2

551641-2

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES�� 0.5 � 0.1




METRIC

FIRST ANGLE 551629-2 D

LEVEL1 2

(ACP) LABEL, LP, IS CANADA-DIGITAL

DRAWN BY: NJ


C 8037 ADDED FRENCH TRANSLATION DR 10/12/15B 7847 IP RATING WAS 66 NJ 12/02/14

1:1

D 8183 ADDED CL I, ZONE0/1 MS 8/18/16

INTRINSICALLY SAFECL. I, Div. 1, GR. ABCD CL.I, ZONE 0/1, Ex ia IIC T4 Ta = -50°C to +71°C ; IP66

when connected in accordance with FM approved installation drawing # 651543-2lorsqu'il est connecté en conformité avec FM approuvé le plan d'installation # 651543-2

WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGSAVERTISSEMENT : se référer au schéma d'installation à la prudence / AVERTISSEMENTS


Model No: Modèle No:

Serial No:Numéro de série:

Date:

R

8 POINT TEXT SIZE


DATE CODE.


4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

C


NOTES:



3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT

P/N: 551629-2 Rev D

®

Fig. 29: Intrinsically Safe FMC label, Modbus and DDA, NEMA Housing

1

1

2

2

A A

B B

551704-LEVEL

METRIC

(ACP) LABEL, LP, IS CANADA-ANALOGMTS SYSTEMS CORPORATIONSENSORS DIVISION3001 SHELDON DRIVE, CARY, NC 27513

FIRST ANGLE E- THREAD DEPTHS ARE TO MIN. FULL THDS

- DRILL DEPTHS ARE TO FULL DIA.- REMOVE BURRS AND SHARP EDGES- DO NOT SCALE PRINT- MACHINED SURFACE FINISH 3.2uM [125 uIn]

mTHE INFORMATION AND DESIGN(S) DISCLOSEDHEREIN ARE THE PROPERTY OF MTS SYSTEMSCORPORATION AND MAY NOT BE USED,REPRODUCED OR DISCLOSED IN ANY FORMEXCEPT AS GRANTED IN WRITING BY MTSSYSTEMS CORPORATION. THIS RESTRICTIONEXCLUDES INFORMATION THAT IS IN THE PUBLIC DOMAIN OR WAS LEGITIMATELY IN THEPRIOR POSSESSION OF THE RECIPIENT.

PROPRIETARY DATA

NJDRAWN BY:

REV

SHEET

DWG NO.

1:1 11 OF

TITLEUNLESS OTHERWISE SPECIFIED

ANGLES��

SIZE

SCALE:PRODUCT LINE

1 PLACEMM

TOLERANCES0 PLACES

MM� 0.1� 0.5


MTS Systems Corp. Sensors Division3001 Sheldon Drive, Cary, N.C. 27513

INTRINSICALLY SAFE: CL. I, Div. 1, GR. ABCD, CL.I Zone 0/1 Ex ia IIC T4Ta = -50°C TO +71°C ; IP65

REFER TO INSTALLATION DWG #651544-2 FOR CAUTION/WARNINGS WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY

Avertissement : Se référer au document DWG # 651544-2 précautions d'installations ATTENTION : La substitution de composants peut compromettre la sécurité intrinsèque

LPXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XX-XX 35.05 [1.38]

"L1"∆ "L2"

17.53 [.69]

8.97 [.35]

3.47 [.14] R

FM C

NOTES:


2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.

3. ∆ INDICATES CRITICAL DIMENSIONS.


5. MATERIAL: .8 [.03] THICK ALUMINUM.

6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.

APPROVED

�Level Plus Transmitter

P/N 551704-X Rev E

4.0 POINT TEXT SIZE (TYP.)

SEE TABLE 1 FOR DASH #


7.5 POINT SIZE


SERIAL NO./DATE CODEMTS TO PRINT MODEL NO.

"D1"

TABLE 1

DASH # HOUSING "L1" "L2" "D1"

-1 ADALET85.85 [3.38]

69.85 [2.75]

Ø2.35 [.09]x2

-2 LIMATHERM 65 [2.56] 58 [2.28] Ø 3.05 [.12] x2

E 8256 ADDED "D1" MS 2/22/17D 8183 ADDED CL 1 ZONE 0/1 MS 8/8/16C 8037 ADDED FRENCH TRANSLATION DR 10/12/15

66 SAW GNITAR PI7487B NJ 12/2/14ETADYBNOITPIRCSED#OCEVER

1

1

2

2

A A

B B

551702-


LEVELMETRIC

(ACP) LABEL, LP, IS CANADA-DIGITALMTS SYSTEMS CORPORATIONSENSORS DIVISION3001 SHELDON DRIVE, CARY, NC 27513

FIRST ANGLE E- THREAD DEPTHS ARE TO MIN. FULL THDS

- DRILL DEPTHS ARE TO FULL DIA.- REMOVE BURRS AND SHARP EDGES- DO NOT SCALE PRINT- MACHINED SURFACE FINISH 3.2uM [125 uIn]

mTHE INFORMATION AND DESIGN(S) DISCLOSEDHEREIN ARE THE PROPERTY OF MTS SYSTEMSCORPORATION AND MAY NOT BE USED,REPRODUCED OR DISCLOSED IN ANY FORMEXCEPT AS GRANTED IN WRITING BY MTSSYSTEMS CORPORATION. THIS RESTRICTIONEXCLUDES INFORMATION THAT IS IN THE PUBLIC DOMAIN OR WAS LEGITIMATELY IN THEPRIOR POSSESSION OF THE RECIPIENT.

PROPRIETARY DATA

NJDRAWN BY:

REV

SHEET

DWG NO.

1:1 11 OF

TITLEUNLESS OTHERWISE SPECIFIED

ANGLES��

SIZE

SCALE:PRODUCT LINE

1 PLACEMM

TOLERANCES0 PLACES

MM� 0.1� 0.5

MTS Systems Corp. Sensors Division3001 Sheldon Drive, Cary, N.C. 27513

INTRINSICALLY SAFE: CL. I, Div. 1, GR. ABCD, CL. I Zone 0/1 Ex ia IIC T4 Ta = -50°C TO +71°C ; IP65

REFER TO INSTALLATION DWG #651543-2 FOR CAUTION/WARNINGS WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY

Avertissement : Se référer au document DWG # 651543-2 précautions d'installations ATTENTION : La substitution de composants peut compromettre la sécurité intrinsèque

LPXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XX-XX 35.05 [1.38]

"L1"∆ "L2"

17.53 [.69]

8.97 [.35]

3.47 [.14] R

FM C

NOTES:


2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.

3. ∆ INDICATES CRITICAL DIMENSIONS.


5. MATERIAL: .8 [.03] THICK ALUMINUM.

6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.

APPROVED

�Level Plus Transmitter

P/N 551702-X Rev E

4.0 POINT TEXT SIZE (TYP.)

SEE TABLE 1 FOR DASH #


7.5 POINT SIZE


SERIAL NO./DATE CODEMTS TO PRINT MODEL NO.

"D1"

TABLE 1


-1 ADALET85.85 [3.38]

69.85[2.75]

Ø2.35 [.09]x2

-2 LIMATHERM 65 [2.56] 58 [2.28] Ø 3.05 [.12] x2

E 8256 ADDED "D1" MS 2/22/17D 8183 ADDED CL 1 ZONE 0/1 MS 8/8/16C 8037 ADDED FRENCH TRANSLATION DR 10/12/15

66 SAW GNITAR PI7487B NJ 12/2/14ETADYBNOITPIRCSED#OCEVER

31


Operation Manual


Fig. 33: Intrinsically Safe FMC installation drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-2

1 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE M

AD

E W

ITHO

UT TH

E NO

TIFICA

TION

TO A

PPR

OV

AL AGE

NC

Y(S).***

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 12/2/14

F

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71C MS 2/23/15

D 8037 AD

DED

FRENCH

TRANSLATIO

N AN

D W

IRING

CHART M

S 11/3/15

E 8183 ADD

ED CL I Zone 0/1 M

S 8/8/16F 8256 U

PDATED

WIRIN

G CH

ART ON

SHEET 2 M

S 1/30/17

24 VDC

COM

MO

N- >

Rx/Tx+

Rx /Tx-

GRO

UN

D

EARTH G

ROU

ND

(SEE NO

TE 4) TERRE( Voir note 4 )

EARTH G

ROU

ND

(SEE NO

TE 4) TERRE( Voir note 4 )

Rx/Tx-

Rx/Tx+

GND

+24V

SAFETY BARRIER Barrière de sécurité

SAFETY BARRIER

Barrière de sécurité

SAFETY BARRIER Barrière de sécurité

NO

TES: (FO

R N

OTE

S IN FR

ENC

H S

EE

PAG

E 3, NO

TES P

OU

R VO

IR E

N FR

AN

ÇA

IS P

AG

E 3)

1.ALL N

ATION

AL A

ND

LOC

AL C

OD

ES

AND

RE

GU

LATIO

NS

MU

ST B

E A

DH

ERE

D TO

WH

EN

INS

TALLIN

G TH

E LEVE

L SE

NS

OR

IN H

AZA

RD

OU

S E

NV

IRO

NM

ENTS

. S

EAL A

LL CO

ND

UITS

WITH

IN 457 M

M(18").

2.LOO

P C

AB

LE M

UST B

E 24 A

WG

TO 14 A

WG

(.511MM

² to 1.6MM

²) S

HIE

LDE

D TW

ISTED

PA

IR C

ABLE W

ITH S

HIE

LD. C

AB

LE C

APA

CITA

NC

E M

US

T B

E LESS

THAN

30 pF PE

R FO

OT (98 pF PE

R M

). CAB

LE S

HIELD

IS C

ON

NE

CTE

D TO

SY

STE

M G

RO

UN

D IN

NO

N-H

AZA

RD

OU

S AR

EA

. SEE

INS

TALLATIO

N M

ANU

AL FO

R

AD

DITIO

NA

L CA

BLE

INFO

RM

ATION

. 3.TH

E R

ESIS

TAN

CE

BETW

EE

N E

AR

TH G

RO

UN

D A

ND

THE IN

TRIN

SIC

ALLY SA

FE G

RO

UN

D M

UST B

E LE

SS TH

AN

1 OH

M.

4.THE

TRAN

SD

UC

ER FR

AM

E S

HALL B

E GR

OU

ND

ED

TO E

AR

TH G

RO

UN

D D

IRE

CTLY O

R TH

RO

UG

H TH

E E

QU

IPM

EN

T ON

WH

ICH

IT IS M

OU

NTE

D.

5. CO

NTR

OL EQ

UIP

ME

NT C

ON

NEC

TED

TO A

SSO

CIA

TED

AP

PAR

ATU

S M

US

T N

OT U

SE

OR

GE

NE

RA

TE M

OR

E TH

AN

250 VR

MS O

R V

DC

6.ASS

OC

IATE

D A

PP

AR

ATU

S M

AN

UFA

CTU

RER

'S INS

TALLA

TION

DR

AW

ING

MU

ST

BE FO

LLOW

ED

WH

EN

INS

TALLING

THIS

EQ

UIP

ME

NT.

7.ON

LY U

SE

CEC

AP

PRO

VE

D BA

RR

IER

S. 8.E

NTITY

PA

RA

ME

TER

S:

S

UP

PLY

: Rx/Tx- : R

x/Tx+ : U

i = 28VDC

Ui= 8.6V

Ui= 8.6V

Ii = 100mA

Ii = 10mA

Ii = 10mA

Ci = 0 µF C

i = 0 µF Ci = 0 µF


Li = 0 µH P

i = 0.7 W P

i= 0.0215 W P

i= 0.0215 W 9.TH

E E

NTITY

CO

NC

EP

T ALLO

WS

INTER

CO

NN

EC

TION

OF IN

TRIN

SICA

LLY S

AFE A

PP

ARA

TUS

WITH

AS

SO

CIATE

D AP

PA

RA

TUS

WH

EN

THE

FOLLO

WIN

G IS TR

UE

: V

max or U

i ≥ Voc, V

t or Uo;


Pm

ax or Pi ≥ Po;

Ca ≥ C

i + Ccable;


UA

L-CAV

ITY E

NC

LOS

UR

ES

: C

US

TOM

ER

CO

NN

EC

TION

S W

ILL BE

MA

DE

AT TE

RM

INA

L BLO

CK

ON

PO

WER

SID

E O

F HO

US

ING

(NO

T TO TE

RM

INA

L BLO

CK

ON

INTE

RC

ON

NEC

T BO

AR

D).

11.FOR

INSTA

LLATIO

N W

ITHIN

CAN

AD

A S

EE

, CA

NA

DIA

N ELEC

TRIC

AL C

OD

E, C

SA

No. C

22.1. 12.TH

E M

AXIM

UM

PE

RM

ITTED

AM

BIENT TE

MP

ERA

TUR

E O

F THE

LEV

EL P

LUS D

IGITA

L/AN

ALO

G

LEV

EL TRA

NSM

ITTER

IS 71 °C

. TO A

VOID

THE

EFFE

CTS

OF P

RO

CE

SS

TEMPE

RA

TUR

E AN

D

OTH

ER

THER

MA

L EFFE

CTS

CAR

E S

HA

LL BE

TAKE

N TO

EN

SUR

E THE

SU

RR

OU

ND

ING

AM

BIE

NT

AN

D TH

E A

MB

IEN

T INS

IDE

THE

TRA

NS

MITTE

R H

OU

SIN

G D

OE

S N

OT EX

CE

ED 71°C

13.CAU

TION

: FLEX

IBLE GA

UG

ES H

AVE

A M

INIM

UM

BEN

D D

IAM

ETE

R O

F 406MM

(16") 14.W

AR

NIN

G: TH

E A

PP

ARA

TUS

EN

CLO

SU

RE

CO

NTA

INS

ALU

MIN

UM

AN

D IS

CO

NS

IDE

RE

D TO

CO

NS

TITUTE A

PO

TEN

TIAL R

ISK

OF IG

NITIO

N B

Y IM

PA

CT O

R FR

ICTIO

N. C

AR

E MU

ST B

E TAK

EN

IN

TO A

CC

OU

NT D

UR

ING

INS

TALLATIO

N A

ND

US

E TO P

RE

VE

NT IM

PA

CT O

R FR

ICTIO

N15.W

AR

NIN

G: S

UB

STITU

TION

OF C

OM

PON

EN

TS M

AY IM

PAIR

INTR

INSIC

SA

FETY.

16.WA

RN

ING

: TO P

REV

EN

T IGN

ITION

OF FLA

MM

AB

LE O

R C

OM

BU

STIB

LE A

TMO

SP

HE

RE

S,

DISC

ON

NE

CT P

OW

ER B

EFO

RE S

ER

VICIN

G

17.WA

RN

ING

: THE

EQ

UIP

ME

NT C

ON

TAINS

NO

N-M

ETA

LLIC E

NC

LOS

UR

E P

AR

TS, TO

PRE

VEN

T TH

E R

ISK O

F ELE

CTR

OS

TATIC

SP

AR

KIN

G. TH

E NO

N-M

ETALLIC

SU

RFA

CE S

HO

ULD

ON

LY B

E CLE

AN

ED

WITH

A D

AMP C

LOTH

.

NO

N H

AZARDO

US LO

CATION

NO

N ZO

NE D

ANG

EREUSE

HAZARD

OU

S LOCATIO

N ZO

NE D

ANG

EREUSE

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(CAN

ADA). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

AGEN

CE D

ESSIN contrôlée ( C

ANAD

A ) . AUC

UN

CH

ANG

EMEN

T sans l'accord préalable AGEN

CE APPR

OBATIO

N

EARTH TERM

INAL

BORN

E DE TERRE

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTRIN

SICALLY SAFE FOR CAN

ADA

LEVEL

FM

APPROVED

C

N/A

INTRIN

SICALLY SAFE (INTRIN

SÈQU

EMEN

T SÛR)

CL. I, DIV. 1, G

R. ABCDCL. I Zone 0/1 Ex ia IIC T4 Ta =

-50 to 71°C ; IP65

32


Operation Manual

DETAIL A

SCALE 1.60 : 1

DETAIL C

SCALE 3 : 1

DETAIL D

SCALE 1.2

DETAIL E

SCALE 1 : 1

A

C

D

E

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-2

2 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE M

AD

E W

ITHO

UT TH

E NO

TIFICA

TION

TO A

PPR

OV

AL AGE

NC

Y(S).***

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 12/2/14

F

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71C MS 2/23/15

D 8037 AD

DED

FRENCH

TRANSLATIO

N AN

D W

IRING

CHART M

S 11/3/15

E 8183 ADD

ED CL I Zone 0/1 M

S 8/8/16F 8256 U

PDATED

WIRIN

G CH

ART ON

SHEET 2 M

S 1/30/17


GND+24V

TX/RX-TX/RX+EARTH

GND

+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING

(Seule cavité & NEM

A LOG

EMEN

T)FIG

UR

E 2D

UAL C

AVITY HO

USIN

G(C

avité double LOG

EMEN

T)

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM Le client doit relier la m

asse LUG

à l'extérieur pour le système au sol SÉC

UR

ITÉ DE TER

RE

WAR

NIN

G:

CO

ND

UIT SEALS R

EQU

IRED

WITH

IN 457 M

M (18") O

F HO

USIN

G.

Étanchéité des conduits requis dans les 457 mm

( 18 " ) DU

LOG

EMEN

T

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTRIN


ADA


PIN W

IRING

CHART (FO

R NEM

A GAG

UE)

WIRIN

G CH

ART (FOR N

EMA G

AUG

E)

LEVEL

WIRE CO

LOR

SIGN

ALRED

24 V PWR

BLACK 0 V PW

RBLU

EN

/AW

HITE

RX TX +G

REENRX TX -

DRAIN

WIRE

EARTH G

ROU

ND

PIN #

SIGN

ALPIN

124 V PW

RPIN

20 V PW

RPIN

3N

/APIN

4RX TX+

PIN 5

RX TX-PIN

6EARTH

GRO

UN

D



33


Operation Manual

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-2

3 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE M

AD

E W

ITHO

UT TH

E NO

TIFICA

TION

TO A

PPR

OV

AL AGE

NC

Y(S).***

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 12/2/14

F

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71C MS 2/23/15

D 8037 AD

DED

FRENCH

TRANSLATIO

N AN

D W

IRING

CHART M

S 11/3/15

E 8183 ADD

ED CL I Zone 0/1 M

S 8/8/16F 8256 U

PDATED

WIRIN

G CH

ART ON

SHEET 2 M

S 1/30/17

NO

TES

:1. La réglem

entation doit être respectée suivant les codes locaux et nationaux LO

RS

D'IN

STALLA

TION

DU

CA

PTE

UR

DE

NIV

EAU

DA

NS

DE

S E

NV

IRO

NN

EM

EN

TS D

AN

GER

EU

X.

Sceller tous les conduits à m

oins de 457 mm

(18 " ). 2. Boucle de câble doit être de 24 A

WG

à 14 AW

G (.511M

M2 à 1.6M

M2)

Paire Torsadée B

lindée avec le bouclier. La capacité du câble devraÊ

tre inférieure à 30 pF PAR

PIE

D (98 pF PA

R M

). Le blindage du câble est raccordéÀ

la terre EN ZO

NE

NO

N D

AN

GER

EU

SE

. VO

IR m

anuel d'installationIN

FOR

MA

TION

S de câble supplémentaire.

3. La résistance entre la TER

RE

ET la zone IN

TRIN

SE

QU

ED

oit être inférieure à 1 ohm.

4. Le boîtier du capteur doit être relié à la TER

RE

directement ou par

L'équipement sur lequel il est m

onté. 5. Equipem

ent de comm

ande relié à l'appareil associé ne doit pas utiliser ou générer plus de 250 VR

MS

OU

VD

C 6 Le plan d'installation associé du fabricant de l'appareil doit être suivi lors de l'installation de cet équipem

ent 7. U

TILISE

R U

NIQ

UEM

ENT D

ES B

AR

RIE

RE

S A

PPR

OU

VÉE

S C

EC.

8. PAR

AMÈTR

ES

:S

UPP

LY: R

x/Tx- : Rx/Tx+ :

Ui = 28V

DC

Ui= 8.6V

Ui= 8.6V

Ii = 100mA

Ii = 10mA

Ii = 10mA

Ci = 0 µF C

i = 0 µF Ci = 0 µF


Li = 0 µHP

i = 0.7 W P

i= 0.0215 W Pi= 0.0215 W

9. Le concept de l'entité permet l'interconnexion de l'appareil de sécurité intrinsèque avec un appareil associé lorsque la suivante est vraie :

Vm

ax or Ui > V

oc, Vt or Uo;

Imax or Ii > Isc, It or Io;

Pm

ax or Pi > Po;

Ca > C

i + Ccable;

La > Li + Lcable. 10. EN

CEIN

TES

à cavité double : Les raccordements clients, seront effectués au bornier d'alim

entation sur le côté du LOG

EM

EN

T boîtier (pas au bornier carte d'interconnexion) 11. Pour une IN

STALLATIO

N A

U C

AN

AD

A, suivre LE

CO

DE C

AN

AD

IEN

DE

L'ÉLE

CTR

ICITÉ

,C

SA N

o C22.1.

12. La TEM

PÉ

RA

TUR

E A

MB

IANTE

maxim

um autorisé pour le capteur LE

VEL PLU

S version D

IGITA

L ou ANA

LOG

IQU

E est de 71 C

°. Pour éviter les effets

de la température sur le processus des protections therm

iques doivent être prises pour assurer la température am

biante environnante et ainsi qu'à l'intérieur du boîtier du capteur la tem

pérature ne doit pas dépasser 71 C°

13. ATTEN

TION

: Le flexible du capteur a un diamètre m

inimum

de courbure de 406 mm

(16 ") 14. ATTE

NTIO

N : Le boîtier de l'appareil contient de l'alum

inium et est considéré

CO

NS

TITUE

R U

N R

ISQ

UE

potentiel de générer des étincelles en cas de choc ou de frottement. V

EU

ILLEZ EN

TEN

IR C

OM

PTE

LOR

S DE

L'IN

STALLA

TION

ET U

TILISATIO

N P

OU

R ÉV

ITER

choc ou frottement

15. ATTEN

TION

: La substitution de composants peut com

promettre la sécurité intrinsèque.

16. ATTEN

TION

: Pour éviter l'inflam

mation d'atm

osphères inflamm

ables ou combustibles,

DÉ

BRA

NC

HEZ L'A

LIME

NTA

TION

AV

AN

T D'IN

TER

VE

NIR

17. ATTEN

TION

: l'équipement contient D

ES

PIECE

S N

ON

ME

TALLIQ

UE

, PO

UR

EV

ITER

LE R

ISQ

UE ÉLE

CTR

OSTA

TIQU

E, étincelles. La surface non m

étallique doit SEU

LEM

EN

T Être nettoyée avec un chiffon hum

id

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTRIN


ADA

LEVEL



34


Operation Manual


Fig. 36: Intrinsically Safe FMC installation drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

RE

VE

CO

#D

ES

CR

IPTIO

N

TITLE

SIZE

DW

G N

O.

RE

V

PR

OD

UC

T LINE

SC

ALE

:

BY

DA

TE

SH

EE

TO

F

UN

LESS O

THER

WISE

SPEC

IFIEDTO

LERA

NC

ES0 P

LAC

ES

MM

1 PLA

CE

MM

ANG

LES

0.5

0.1

- THR

EAD D

EPTH

S ARE TO

MIN

. FULL TH

DS

- DR

ILL DEP

THS AR

E TO FU

LL DIA.

- RE

MO

VE BUR

RS AN

D SH

ARP ED

GE

S- D

O N

OT SC

ALE PR

INT

- MAC

HIN

ED S

UR

FACE

FINISH

3.2uM [125 uIn]

PR

OP

RIE

TAR

Y D

ATA

THE

INFO

RM

ATIO

N A

ND

DES

IGN

(S) DIS

CLO

SEDH

ERE

IN AR

E TH

E PRO

PERTY

OF M

TS SY

STEMS

CO

RPO

RATIO

N AN

D M

AY N

OT BE U

SED

,R

EPRO

DU

CED

OR

DIS

CLO

SED IN

AN

Y FO

RM

EXCEPT AS

GR

ANTE

D IN

WR

ITING

BY M

TSSYS

TEMS C

OR

POR

ATION

. THIS R

ESTR

ICTIO

NEXC

LUD

ES IN

FOR

MATIO

N TH

AT IS IN

THE

PU

BLIC D

OM

AIN

OR

WAS LEG

ITIMA

TELY IN TH

EPR

IOR

POSSE

SSION

OF TH

E REC

IPIENT.

mM

TS SY

STE

MS

CO

RP

OR

ATIO

NSEN

SO

RS D

IVISIO

N3001 SH

ELD

ON

DR

IVE, CAR

Y, N

C 27513

METRIC

FIRS

T A

NG

LED

651544-2LE

VE

L1

3

DR

AWN

BY:

MS

1:1

***NO

RE

VISION

S SH

ALL BE

MAD

E W

ITHO

UT N

OTIFIC

ATIO

N TO

APPR

OVA

L AGEN

CY

(S)***

B 7847 U

PDA

TED

IP R

ATIN

G FO

R H

OU

SING

TYPE M

S 12/2/14C

7898 UP

DATE

D TE

MPE

RA

TUR

E O

N N

OTE 12 TO

71°C M

S 2/23/15

D 8037 A

DD

ED FR

ENC

H TR

ANS

LATIO

N M

S 11/3/15

E 8183 AD

DE

D C

L I Zone0/1 MS

8/18/16F 8256 U

PDATED

WIR

ING

CHART O

N SH

EET 2 MS 1/30/17

NO

N H

AZA

RD

OU

S LO

CA

TION

NO

N ZO

NE

DA

NG

ER

EU

SE

HA

ZAR

DO

US

LOC

ATIO

NZO

NE

DA

NG

ER

EU

SE

NO

TES

: (FOR

NO

TES IN

FRE

NC

H SE

E P

AG

E 3, N

OTES

PO

UR

VO

IR E

N FR

AN

��

AIS P

AG

E 3)

1. ALL NATIO

NA

L AND

LOC

AL CO

DES

AN

D R

EG

ULA

TION

S M

UST B

E A

DH

ERE

D TO

WH

EN IN

STA

LLING

THE

MTS

LP SEN

SO

R IN

HA

ZARD

OU

S EN

VIRO

NM

EN

TS.

SEA

L ALL CO

ND

UITS

WITH

IN 457 M

M (18").

2. LOO

P C

ABLE M

UST B

E 24 AW

G TO

14 AW

G (.511M

M² to 1.6M

M²)

SHIE

LDED

TWIS

TED P

AIR C

ABLE

WITH

SH

IELD

. CA

BLE

CA

PAC

ITAN

CE M

US

T BE

LESS

THA

N 30 pF P

ER FO

OT (98 pF PE

R m

). CAB

LE SH

IELD

IS C

ON

NE

CTE

D TO

SY

STE

M G

RO

UN

D IN

NO

N-H

AZA

RD

OU

S AREA

. SEE

INS

TALLATIO

N M

AN

UA

L FOR

AD

DITIO

NAL C

ABLE

INFO

RM

ATION

. 3. TH

E RE

SIS

TANC

E B

ETW

EE

N E

AR

TH G

RO

UN

D AN

D TH

E IN

TRIN

SIC

ALLY SA

FE G

RO

UN

D M

UST BE LES

S TH

AN

1 OH

M.

4. THE TR

ANSD

UC

ER FR

AM

E SH

ALL BE

GR

OU

ND

ED TO

EAR

TH G

RO

UN

D D

IRE

CTLY

OR

THR

OU

GH

THE

EQU

IPM

ENT O

N W

HIC

H IT IS

MO

UN

TED

. 5. C

ON

TRO

L EQ

UIP

ME

NT C

ON

NE

CTE

D TO

AS

SO

CIA

TED

APP

AR

ATU

S M

US

T N

OT U

SE

OR

GE

NE

RA

TE M

OR

E TH

AN

250 VR

MS O

R V

DC

. 6. AS

SO

CIA

TED

APP

AR

ATUS

MA

NU

FACTU

RE

R'S

INS

TALLATIO

N D

RA

WIN

G M

US

T BE

FOLLO

WE

D W

HE

N IN

STALLIN

G TH

IS EQ

UIPM

EN

T 7. O

NLY

US

E C

EC

APP

RO

VED

BAR

RIER

S. 8. AP

PR

OV

ED LO

OP

SEP

AR

ATIO

N M

ETH

OD

S:

*RU

N LO

OP

S IN S

EPAR

ATE

CA

BLES

*RU

N LO

OP

S IN S

EPAR

ATE

GR

OU

ND

ED

SH

IELD

S 9. EN

TITY P

ARAM

ETE

RS

EAC

H LO

OP

: U

i = 28 VD

C Ii = 120 m

A C

i = 0 µF Li = 5 µH P

i = 840 mW

10. DU

AL-C

AV

ITY EN

CLO

SU

RES

: C

USTO

ME

R C

ON

NE

CTIO

NS W

ILL BE M

AD

E A

T TER

MIN

AL BLOC

K O

N P

OW

ER SID

E O

F HO

USIN

G (N

OT TO

TER

MIN

AL B

LOC

K O

N IN

TER

CO

NN

EC

T BO

AR

D)

11 FOR

INSTA

LLATION

WITH

IN C

ANAD

A, SE

E CA

NA

DIA

N E

LEC

TRIC

AL C

OD

E, C

SA N

o C22.1.

12.THE

MAX

IMU

M P

ER

MITTED

AM

BIEN

T TEM

PE

RA

TUR

E OF TH

E LEV

EL PLU

S DIG

ITAL/A

NA

LOG

LEV

EL TR

AN

SM

ITTER

IS 71 °C

. TO A

VO

ID TH

E EFFE

CTS O

F PR

OC

ESS

TEMPE

RA

TUR

E AN

D

OTH

ER

THE

RM

AL EFFEC

TS C

ARE S

HA

LL BE TA

KEN

TO E

NSU

RE

THE

SUR

RO

UN

DIN

G A

MBIE

NT

AND

THE

AM

BIEN

T INSID

E THE TR

AN

SMITTE

R H

OU

SIN

G D

OE

S N

OT E

XCE

ED 71°C

13.CA

UTIO

N: FLEX

IBLE GA

UG

ES H

AV

E A M

INIM

UM

BEN

D R

AD

IUS

OF 406M

M (16")

14. WA

RN

ING

: THE A

PP

AR

ATU

S E

NC

LOSU

RE

CO

NTA

INS

ALUM

INU

M AN

D IS

CO

NS

IDE

RE

D TO

CO

NSTITU

TE A

POTE

NTIA

L RIS

K O

F IGN

ITION

BY IM

PA

CT O

R FR

ICTIO

N. C

AR

E M

US

T BE TA

KEN

IN

TO A

CC

OU

NT D

UR

ING

INS

TALLATIO

N A

ND

US

E TO

PREV

EN

T IMP

ACT O

R FR

ICTIO

N 15.W

AR

NIN

G: S

UBS

TITUTIO

N O

F CO

MP

ON

ENTS M

AY IM

PAIR

INTR

INS

IC SA

FETY

. 16.W

AR

NIN

G: TO

PREV

EN

T IGN

ITION

OF FLA

MM

ABLE

OR

CO

MB

US

TIBLE

ATM

OSP

HE

RES

. D

ISC

ON

NE

CT P

OW

ER

BEFO

RE S

ER

VIC

ING

. 17.W

AR

NIN

G: TH

E E

QU

IPM

EN

T CO

NTA

INS

NO

N-M

ETALLIC

EN

CLO

SU

RE

PAR

TS, TO

PR

EVE

NT

THE

RIS

K OF E

LEC

TRO

STA

TIC S

PAR

KING

. THE

NO

N-M

ETA

LLIC S

UR

FACE

SH

OU

LD O

NLY

BE C

LEAN

ED

WITH

A DA

MP

CLO

TH.

EAR

TH G

RO

UN

D LU

G N

OTE

3

AG

ENC

Y CO

NTR

OLLED

DR

AWIN

G (C

anada). NO

CH

ANG

ES W

ITHO

UT PR

IOR

AGE

NC

Y APPR

OVAL

AG

ENC

E DE

SSIN contrôlée ( C

AN

ADA ) . A

UC

UN

CH

ANG

EM

EN

T sans l'accord préalable AGE

NC

E APPR

OBATIO

N

24 VD

C

CO

NTR

OL

INP

UT 1

CO

NTR

OL

INP

UT 2

APP

RO

VE

D S

AFETY

BA

RR

IER sécurité approuvé B

AR

RIÈR

ELO

OP

VO

LTAG

E

SH

IELD

SH

IELD

LOO

P 1+

LOO

P 1-

LOO

P 2+

LOO

P 2-

FM

APPROVED

USC

(ACP) INSTALLATIN

DW

G LP AN

ALOG

INTRIN


ADA

SING

LE OR

DU

AL C

AVITY

NE

MA

HO

US

ING

F

INTRIN


IV. 1, GR. ABCD

CL.I Zone 0/1 Ex ia IIC T4Ta =

-50 to 71°C ; IP65

AP

PR

OV

ED

SAFE

TY BA

RR

IER

sécurité approuvé BA

RR

IÈR

E

EARTH G

RO

UN

D(SEE N

OTE 4)

TERRE

( Voir note 4 )

EARTH G

ROU

ND

(SEE NO

TE 4) TERR

E( Voir note 4 )

35


Operation Manual

12.3.3 Installation drawing (cont.)12.4.1.3 Installation drawing (cont.)


DE

TAIL DS

CALE

3

DETA

IL ES

CA

LE 1.60

DETAIL F

SCALE

1.2

DETA

IL HSC

ALE 1 : 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

RE

VE

CO

#D

ES

CR

IPTIO

N

TITLE

SIZE

DW

G N

O.

RE

V

PR

OD

UC

T LINE

SC

ALE

:

BY

DA

TE

SH

EE

TO

F

UN

LESS O

THER

WISE

SPEC

IFIEDTO

LERA

NC

ES0 P

LAC

ES

MM

1 PLA

CE

MM

ANG

LES

0.5

0.1

- THR

EAD D

EPTH

S ARE TO

MIN

. FULL TH

DS

- DR

ILL DEP

THS AR

E TO FU

LL DIA.

- RE

MO

VE BUR

RS AN

D SH

ARP ED

GE

S- D

O N

OT SC

ALE PR

INT

- MAC

HIN

ED S

UR

FACE

FINISH

3.2uM [125 uIn]

PR

OP

RIE

TAR

Y D

ATA

THE

INFO

RM

ATIO

N A

ND

DES

IGN

(S) DIS

CLO

SEDH

ERE

IN AR

E TH

E PRO

PERTY

OF M

TS SY

STEMS

CO

RPO

RATIO

N AN

D M

AY N

OT BE U

SED

,R

EPRO

DU

CED

OR

DIS

CLO

SED IN

AN

Y FO

RM

EXCEPT AS

GR

ANTE

D IN

WR

ITING

BY M

TSSYS

TEMS C

OR

POR

ATION

. THIS R

ESTR

ICTIO

NEXC

LUD

ES IN

FOR

MATIO

N TH

AT IS IN

THE

PU

BLIC D

OM

AIN

OR

WAS LEG

ITIMA

TELY IN TH

EPR

IOR

POSSE

SSION

OF TH

E REC

IPIENT.

mM

TS SY

STE

MS

CO

RP

OR

ATIO

NSEN

SO

RS D

IVISIO

N3001 SH

ELD

ON

DR

IVE, CAR

Y, N

C 27513

METRIC

FIRS

T A

NG

LED

651544-2LE

VE

L2

3

DR

AWN

BY:

MS

1:1

***NO

RE

VISION

S SH

ALL BE

MAD

E W

ITHO

UT N

OTIFIC

ATIO

N TO

APPR

OVA

L AGEN

CY

(S)***

B 7847 U

PDA

TED

IP R

ATIN

G FO

R H

OU

SING

TYPE M

S 12/2/14C

7898 UP

DATE

D TE

MPE

RA

TUR

E O

N N

OTE 12 TO

71°C M

S 2/23/15

D 8037 A

DD

ED FR

ENC

H TR

ANS

LATIO

N M

S 11/3/15

E 8183 AD

DE

D C

L I Zone0/1 MS

8/18/16F 8256 U

PDATED

WIR

ING

CHART O

N SH

EET 2 MS 1/30/17

D

E

F

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

H

NO

TES:

1. THE C

USTO

ME

R S

HO

ULD

CO

NN

ECT TH

E OU

TSIDE G

RO

UN

D LU

G TO

THE

SA

FETY E

AR

THIN

G G

RO

UN

D SY

STEM Le client doit relier la m

asse LUG

à l'extérieur pour le système au sol S

ÉC

UR

ITÉ DE

TERR

E W

ARN

ING

: C

ON

DU

IT SEA

LS R

EQ

UIR

ED

WITH

IN 457 M

M (18") O

F HO

US

ING

. Étanchéité des conduits requis dans les 457 m

m ( 18 " ) D

U LO

GE

MEN

T.

FIGU

RE

2D

UA

L CAV

ITY H

OU

SIN

G


FIGU

RE 1

SING

LE C

AVITY & N

EM

A HO

US

ING



F

PIN W

IRING

CHAR

T (FOR

NEM

A GAU

GE)

WIR

ING

CHART(FO

R N

EMA G

AUG

E)

(ACP) INSTALLATIN

DW

G LP AN

ALOG

INTRIN

SICALLY SAFE FOR

CANAD

A

WIRE CO

LOR

SIGN

ALRED

LOO

P 1+BLACK

LOO

P 1-BLU

ELO

OP 2-

WH

ITELO

OP 2+

GR

EENN

/AD

RAIN

WIRE

EARTH

GR

OU

ND

PIN #

SIGN

ALPIN

1LO

OP 1-

PIN 2

LOO

P 1+PIN

3LO

OP 2-

PIN 4

LOO

P 2+PIN

5N

/APIN

6EAR

TH G

RO

UN

D

36


Operation Manual

12.3.3 Installation drawing (cont.)12.4.1.3 Installation drawing (cont.)


11

22

33

44

55

66

77

88

AA

BB

CC

DD

RE

VE

CO

#D

ES

CR

IPTIO

N

TITLE

SIZE

DW

G N

O.

RE

V

PR

OD

UC

T LINE

SC

ALE

:

BY

DA

TE

SH

EE

TO

F

UN

LESS O

THER

WISE

SPEC

IFIEDTO

LERA

NC

ES0 P

LAC

ES

MM

1 PLA

CE

MM

ANG

LES

0.5

0.1

- THR

EAD D

EPTH

S ARE TO

MIN

. FULL TH

DS

- DR

ILL DEP

THS AR

E TO FU

LL DIA.

- RE

MO

VE BUR

RS AN

D SH

ARP ED

GE

S- D

O N

OT SC

ALE PR

INT

- MAC

HIN

ED S

UR

FACE

FINISH

3.2uM [125 uIn]

PR

OP

RIE

TAR

Y D

ATA

THE

INFO

RM

ATIO

N A

ND

DES

IGN

(S) DIS

CLO

SEDH

ERE

IN AR

E TH

E PRO

PERTY

OF M

TS SY

STEMS

CO

RPO

RATIO

N AN

D M

AY N

OT BE U

SED

,R

EPRO

DU

CED

OR

DIS

CLO

SED IN

AN

Y FO

RM

EXCEPT AS

GR

ANTE

D IN

WR

ITING

BY M

TSSYS

TEMS C

OR

POR

ATION

. THIS R

ESTR

ICTIO

NEXC

LUD

ES IN

FOR

MATIO

N TH

AT IS IN

THE

PU

BLIC D

OM

AIN

OR

WAS LEG

ITIMA

TELY IN TH

EPR

IOR

POSSE

SSION

OF TH

E REC

IPIENT.

mM

TS SY

STE

MS

CO

RP

OR

ATIO

NSEN

SO

RS D

IVISIO

N3001 SH

ELD

ON

DR

IVE, CAR

Y, N

C 27513

METRIC

FIRS

T A

NG

LED

651544-2LE

VE

L3

3

DR

AWN

BY:

MS

1:1

***NO

RE

VISION

S SH

ALL BE

MAD

E W

ITHO

UT N

OTIFIC

ATIO

N TO

APPR

OVA

L AGEN

CY

(S)***

B 7847 U

PDA

TED

IP R

ATIN

G FO

R H

OU

SING

TYPE M

S 12/2/14C

7898 UP

DATE

D TE

MPE

RA

TUR

E O

N N

OTE 12 TO

71°C M

S 2/23/15

D 8037 A

DD

ED FR

ENC

H TR

ANS

LATIO

N M

S 11/3/15

E 8183 AD

DE

D C

L I Zone0/1 MS

8/18/16F 8256 U

PDATED

WIR

ING

CHART O

N SH

EET 2 MS 1/30/17

NO

TES

:1. La réglem


RS

D'IN

STALLA

TION

DU

CA

PTE

UR

DE

NIV

EAU

DA

NS

DE

S E

NV

IRO

NN

EM

EN

TS D

AN

GE

RE

UX

.S

celler tous les conduits à moins de 457 m

m (18 " ).

2. Boucle de câble doit être de 24 A

WG

à 14 AW

G (.511M

M2 à 1.6M

M2)

Paire Torsadée Blindée avec le bouclier. La capacité du câble devraÊ

tre inférieure à 30 pF PA

R P

IED

(98 pF PAR

M). Le blindage du câble est raccordé

À la terre E

N ZO

NE

NO

N D

AN

GE

RE

US

E. VO

IR m

anuel d'installationIN

FOR

MATIO

NS

de câble supplémentaire.

3. La résistance entre la TER

RE E

T la zone INTR

INS

EQU

ED

oit être inférieure à 1 ohm.

4. Le boîtier du capteur doit être relié à la TER

RE

directement ou par

L'équipement sur lequel il est m

onté. 5. E

quipement de com

mande relié à l'appareil associé ne doit pas utiliser ou générer plus de 250 V

RM

S O

U V

DC

6 Le plan d'installation associé du fabricant de l'appareil doit être suivi lors de l'installation de cet équipement

7. UTILISE

R U

NIQ

UEM

EN

T DES

BA

RR

IER

ES

AP

PR

OU

VÉ

ES

CEC

8. approuvent les méthodes de séparation Loop:

* BOU

CLE

S R

UN

dans des câbles séparés * BO

UC

LES

RU

N S

hields terre séparés 9. P

aramètres d'entité chaque boucle:

Ui = 28 V

DC

Ii = 120 mA

Ci = 0 µF

Li = 5 µH P

i = 840 mW

10. EN

CEIN

TES

à cavité double : Les raccordements clients, seront effectués au bornier d'alim

entation sur le côté du LO

GE

MEN

T boîtier (pas au bornier carte d'interconnexion) 11. P

our une INS

TALLA

TION

AU

CA

NA

DA

, suivre LE C

OD

E C

AN

AD

IEN

DE

L'ÉLEC

TRIC

ITÉ,C

SA

No C

22.1. 12. La TEM

PÉ

RA

TUR

E A

MB

IAN

TE m

aximum

autorisé pour le capteur LEV

EL P

LUS

version DIG

ITAL ou A

NA

LOG

IQU

E est de 71 C

°. Pour éviter les effets de la tem

pérature sur le processus des protections thermiques

doivent être prises pour assurer la température am

biante environnante et ainsi qu'à l'intérieur du boîtier du capteur la tem

pérature ne doit pas dépasser 71 C°

13. ATTE

NTIO

N : Le flexible du capteur a un diam

ètre minim

um de courbure de 406 m

m (16 ")

14. ATTE

NTIO

N : Le boîtier de l'appareil contient de l'alum

inium et est considéré

CO

NS

TITUE

R U

N R

ISQ

UE

potentiel de générer des étincelles en cas de choc ou de frottement. V

EUILLE

Z EN

TEN

IR

CO

MP

TE LOR

S D

E L'IN

STALLA

TION

ET U

TILISATIO

N P

OU

R É

VITE

R choc ou frottem

ent 15. A

TTEN

TION

: La substitution de composants peut com

promettre la sécurité intrinsèque.

16. ATTE

NTIO

N: P

our éviter l'inflamm

ation d'atmosphères inflam

mables ou com

bustibles,D

ÉB

RA

NC

HE

Z L'ALIM

EN

TATIO

N A

VAN

T D'IN

TER

VEN

IR 17. A

TTEN

TION

: l'équipement contient D

ES

PIEC

ES

NO

N M

ETA

LLIQU

E, P

OU

R E

VITE

RLE

RIS

QU

E É

LEC

TRO

STA

TIQU

E, étincelles. La surface non m

étallique doit SEU

LEM

EN

T Être nettoyée avec un

chiffon humid

F

(ACP) INSTALLATIN

DW

G LP AN

ALOG

INTRIN


ADA

37


Operation Manual


12.4.2.2 Labels

Fig. 41: Explosionproof, FMC label, HART®, Housing Option G, H, or L

Fig. 40: Explosionproof, FMC label, Modbus or DDA, Housing Option D, E

Fig. 39: Explosionproof, FMC label, Modbus or DDA Housing Option G, H, or L

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC

FIRST ANGLE A 551708-x A

1 1

DRAWN BY: MS


Level Plus TransmitterFM16CA0130X

�


WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE. ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR.Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65

INSTALL PER # 651553-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: 4-20mA


(ACP) LABEL, LP, XP CANADA - ANALOG

BCD T6...T3

FM APPROVED

P/N 551708-1 Rev A

LEVEL

1:1

R

!

C

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY: MS




FM16CA0130X

INSTALL PER # 651552-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: RS485

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT.POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR. BCD T6...T3 Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65


(ACP) LABEL, LP, XP CANADA - DIGITAL

R FM APPROVED

P/N 551706-2 REV A

LEVEL

1:1

!

C

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY: MS




FM16CA0130X

INSTALL PER # 651552-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: RS485

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT.POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR BCD T6...T3. Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65


(ACP) LABEL, LP, XP CANADA - DIGITAL

R FM APPROVED

P/N 551706-1 REV A

LEVEL

1:1

!

C

Fig. 42: Explosionproof, FMC label, HART®, Housing Option D, E

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METRIC


1 1

DRAWN BY: MS


Level Plus TransmitterFM16CA0130X

�


WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE. ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR. BCD T6...T3Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65

INSTALL PER # 651553-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: 4-20mA


(ACP) LABEL, LP, XP CANADA - ANALOG

FM APPROVED

P/N 551708-2 Rev A

LEVEL

1:1

R

!

C



1. Warning: The equipment contains non-metallic enclosure and process parts, to prevent the risk of electrostatic sparking. The non-metallic surface should only be cleaned with a damp cloth. Painted surface of the equipment may store electrostatic charge and become a source of ignition in applications with a low relative humidity <~30% relative humidity where the painted surface is relatively free of surface contamination such as dirt, dust or oil. Cleaning of the painted surface should only be done with a damp cloth.2. Cables shall be rated > 5°C above maximum ambient temperature.3. To maintain the ingress protection rating of IP65, Teflon tape (3 wraps) or pipe dope shall be used. Refer to Installation Instructions.4. The equipment can be installed in the boundary wall between an EPL Ga area and the less hazardous area, EPL Gb. In this configuration, the process connection is installed in EPL Ga, while the transmitter housing is installed in EPL Gb. Refer to installation instructions.5. Flexible gauges have a minimum bend radius of 381 mm (15 inches).6. Flamepaths not for repair.7. The applicable temperature class, ambient temperature range and process temperature range of the equipment is as follows:



38


Operation Manual


Fig. 43: Explosionproof, FMC Installation Drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651553-2A

LEVEL1

3

DR

AWN

BY: M

S1:1

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

)***A

7957 RE

LEAS

E TO PR

OD

UC

TION

MS 10/22/15

Rx /Tx+

Rx /Tx-

EARTH G

ROU

ND

24 VDC

COM

MO

N-

EARTH G

ROU

ND

SEE NO

TE 8EPL G

a

EPL Gb

NO

N H

AZAR

DO

US LO

CATIO

NH

AZAR

DO

US

LOC

ATIO

N

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(Canada). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

FM

APPROVED US

C

(ACP) INSTALLATIO

N D

WG

LP ANALO

G EXPLO

SION

PROO

F CANAD

A

SING

LE OR

DU

AL CAVITY

FM Canada - FM

16CA

0130XEXPLO

SION

PRO

OF

CL. I, DIV. 1, G

R. BCD T6...T3

Ex db IIB+H

2 T6...T3 Ga/G

bTa =

-40°C to +71°C ; IP65

CO

ND

UIT SEAL

CO

ND

UIT

CO

ND

UIT SEAL

SEE NO

TE 1

NO

TES:

1.ALL N

ATIO

NAL A

ND

LOC

AL C

OD

ES A

ND

RE

GU

LATIO

NS

MU

ST BE

ADH

ERE

D TO

WH

EN IN

STALLING

THE LEV

EL SEN

SOR

IN H

AZAR

DO

US E

NV

IRO

NM

ENTS

. FO

R ZO

NE

INS

TALLATION

S, A S

EAL S

HALL B

E INS

TALLED W

ITHIN

50mm

OF TH

E EN

CLO

SUR

E. FO

R D

IVISIO

N IN

STALLA

TION

S, A

SEAL SH

ALL B

E IN

STALLE

D W

ITHIN

18 INC

HE

S OF TH

E EN

CLO

SU

RE.

2.DU

AL-C

AVITY E

NC

LOS

UR

ES:

CU

STO

MER

CO

NN

ECTIO

NS

WILL BE

MA

DE AT TER

MIN

AL BLO

CK O

N P

OW

ER SID

E O

F HO

USIN

G (N

OT TO

TER

MIN

AL B

LOC

K O

N IN

TERC

ON

NE

CT BO

AR

D). SE

E FIGU

RE

2 ON

PAG

E 2

3. CA

UTIO

N: FLEX

IBLE G

AU

GES

HAV

E A MIN

IMU

M BE

ND

RA

DIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PR

EVEN

T IGN

ITION

OF FLA

MM

ABLE O

R C

OM

BU

STIBLE

ATMO

SPH

ER

ES,

DIS

CO

NN

ECT PO

WE

R B

EFOR

E SER

VICIN

G

5.WAR

NIN

G: TH

E E

QU

IPM

EN

T CO

NTAIN

S N

ON

-META

LLIC EN

CLO

SU

RE

AND

PRO

CE

SS PA

RTS, TO

PR

EVEN

T TH

E R

ISK O

F ELECTR

OSTA

TIC SP

AR

KING

. THE

NO

N-M

ETALLIC

SUR

FAC

E AN

D P

RO

CES

S PAR

TS S

HO

ULD

ON

LY

BE C

LEAN

ED W

ITH A

DA

MP C

LOTH

. PAINTED

SURFACE O

F THE EQ

UIPM

ENT M

AY STORE ELECTRO

STATIC CHARG

E AN

D BECO

ME A SO

URCE O

F IGN

ITION

IN APPLICATIO

NS W

ITH A LO

W RELATIVE H

UM

IDITY <

~30%

RELATIVE

HU

MID

ITY WH

ERE THE PAIN

TED SU

RFACE IS RELATIVELY FREE O

F SURFACE CO

NTAM

INATIO

N SU

CH AS D

IRT, D

UST O

R O

IL. CLEANIN

G O

F THE PAIN

TED SU

RFACE SHO

ULD

ON

LY BE DO

NE

WITH

A DAM

P CLOTH

.6. C

ABLES

SHA

LL BE

RATE

D > 5C

AB

OV

E MAX

IMU

M AM

BIEN

T TEMP

ER

ATUR

E.

7. TO M

AIN

TAIN TH

E IN

GR

ESS

PRO

TEC

TION

RATIN

G O

F IP65, TEFLON

TAPE

(3 WR

APS) O

R P

IPE D

OPE

SHA

LL B

E USE

D. R

EFE

R TO

INS

TALLATIO

N IN

STR

UC

TION

S.8. TH

E EQ

UIP

ME

NT C

AN B

E INSTA

LLED

IN TH

E BO

UN

DA

RY

WA

LL BETW

EEN

A ZO

NE

0 AR

EA A

ND

THE

LESS H

AZAR

DO

US

AREA

, ZON

E 1. IN

THIS C

ON

FIGU

RA

TION

, THE P

RO

CES

S C

ON

NEC

TION

IS IN

STALLED

IN

A ZON

E 0 AREA

, WH

ILE THE

TRAN

SMITTE

R H

OU

SING

IS INS

TALLED IN

A ZON

E 1 A

REA

. 9. TH

E AP

PLICAB

LE TEM

PER

ATUR

E C

LASS

OF TH

E E

QU

IPME

NT, A

MBIE

NT TEM

PER

ATUR

E R

AN

GE,

AN

D M

AXIM

UM

PR

OC

ESS TE

MP

ERA

TUR

E O

F THE

EQU

IPM

EN

T IS AS

FOLLO

WS

; T3 W

ITH P

RO

CES

S TEM

PER

ATU

RE R

AN

GE O

F -40°C to +150°C

T4 WITH

PR

OC

ESS TE

MP

ERA

TUR

E RA

NG

E OF -40°C

to +135°C T5 W

ITH P

RO

CES

S TEM

PER

ATU

RE R

AN

GE O

F -40°C to +100°C

T6 WITH

PR

OC

ESS TE

MP

ERA

TUR

E RA

NG

E OF -40°C

to +85°C A

MB

IENT TE

MP

ERA

TUR

E RA

NG

E -40°C Ta+71°C10. W

HE

N M

OU

NTIN

G O

N A M

AGN

ETIC

LEVE

L GAU

GE

MA

KE SU

RE

THE

ELEC

TRO

NIC

HE

AD AN

D P

RE

SSU

RE

BAR

RIER

HA

VE A

MIN

IMU

M S

PAC

ING

OF 5 IN

CH

ES. SE

E INSTA

LLATIO

N M

ANU

AL FOR

DE

TAIL11. FLA

ME

PATH

S AR

E N

OT FO

R R

EPA

IR

5"[127mm

] Minim

um

39


Operation Manual



DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

D

E

F

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651553-2A

LEVEL2

3

DR

AWN

BY: M

S1:1

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

)***A

7957 RE

LEAS

E TO PR

OD

UC

TION

MS 10/22/15

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES:

1. THE C

USTO

ME

R SH

OU

LD C

ON

NEC

T THE O

UTS

IDE G

RO

UN

D LU

G TO

THE SAFE

TY EARTH

ING

GR

OU

ND

SYSTEM

WAR

NIN

G:

WH

EN IN

STALLING

THE

LEVEL S

ENSO

R IN

HAZAR

DO

US E

NV

IRO

NM

EN

TS. FO

R ZO

NE IN

STALLA

TION

S, A S

EAL SH

ALL BE IN

STALLED

WITH

IN 50m

m O

F THE

EN

CLO

SUR

E. FO

R D

IVISION

INS

TALLATION

S, A SE

AL SH

ALL BE IN

STALLE

D W

ITHIN

18 INC

HES O

F THE EN

CLO

SUR

E.

FIGU

RE 2

DU

AL CAV

ITY HO

USIN

G


FIGU

RE 1

SING

LE CAVITY H

OU

SING


(ACP) INSTALLATIO

N D

WG

LP ANALO

G EXPLO

SION

PROO

F CANAD

A

40


Operation Manual



11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651553-2A

LEVEL3

3

DR

AWN

BY: M

S1:1

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

)***A

7957 RE

LEAS

E TO PR

OD

UC

TION

MS 10/22/15

NO

TES:1. La réglem


RS D

'INSTALLATIO

N D

U C

APTEUR

DE N

IVEAU D

ANS D

ES ENVIR

ON

NEM

ENTS D

ANG

EREU

X. PO

UR

INSTALLATIO

NS D

E ZON

E, UN

SOR

TIE EST INSTALLÉ D

ANS LES 50 m

m D

E L'ENC

EINTE.

POU

R IN

STALLATION

S DE D

IVISION

ALE SOR

TIE EST INSTALLÉ D

ANS LES 18 PO

UC

ES DE L'EN

CEIN

TE2. EN

CEIN

TES à cavité double : Les raccordements clients, seront effectués au bornier d'alim


EMEN

T boîtier (pas au bornier carte d'interconnexion) 3. ATTEN

TION

: LES INSTR

UM

ENTS FLEXIBLES AVEC

UN

RAD

IOD

E MIN

IMU

M D

E 381mm

(15 ")4. ATTEN

TION

: Pour éviter l'inflamm


mables ou com

bustibles, D

ÉBRAN

CH

EZ L'ALIMEN

TATION

AVANT D

'INTER

VENIR

5. AVERTISSEM

ENT: L'ÉQ

UIPEM

ENT C

ON

TENU

E DES PIÈC

ES ET PRO

CÉD

ÉS NO

N-M

ETALLIQU

ES POU

R PR

ÉVENIR

LE RISQ

UE D

'ÉCLAIR

AGE ÉLEC

TRO

STATIQU

E. LA SUR

FACE ET LES PIÈC

ES DE PR

OC

ÉDU

RE N

ON

MÉTALLIQ

UES D

OIVEN

T SEULEM

ENT

EFFECTEZ U

N PAN

NEAU

DE PLAISIR

. LA SUR

FACE PEIN

TÉE DE L'ÉQ

UIPEM

ENT PEU

T CO

NSER

VER LE C

HAR

GE ÉLEC

TRO

STATIQU

E ET D

EVENIR

UN

E SOU

RC

E D'ALLU

MAG

E DAN

S DES APPLIC

ATION

S AVEC U

NE H

UM

IDITÉ BASSE R

ELATIVE <~ 30% R

ELATIVE H

UM

IDITE O

Ù LA SU

RFAC

E PEINTU

RE EST R

ELATIVEMEN

T LIBRE D

E CO

NTAM

INATIO

N D

E SUR

FACE

TELS QU

E LA VIAND

E, LA POU

SSIÈRE O

U L'H

UILE. LE N

ETTOYAG

E DE LA SU

RFAC

E PEINTU

RE D

OIT ÊTR

E FAIT AVEC

UN

PANN

EAU D

E PLAISIR.

6. CABLES doit être évalué> 5C

DESSU

S MAXIM

UM

TEMPER

ATUR

E AMBIAN

TE.7. PO

UR

MAIN

TENIR

LA NO

TATION

DE PR

OTEC

TION

DE IN

GR

ESS IP65, du ruban téflon (3 BAND

ES) ou PIPE DO

PE DEVR

A ÊTRE U

TILISÉ. CO

NSU

LTER LES IN

STRU

CTIO

NS D

'INSTALLATIO

N.

8. L'ÉQU

IPEMEN

T PEUT ÊTR

E INSTALLÉ D

ANS LE M

UR

DE LIM

ITE ENTR

E UN

E ZON

E 0 ET LA ZO

NE M

OIN

S DAN

GER

EUSE, ZO

NE 1. D

ANS C

ETTE CO

NFIG

UR

ATION

, LA CO

NN

EXION

DU

PRO

CESSU

S EST INSTALLEE

DAN

S UN

E ZON

E 0, LOR

SQU

E LE BOITIER

DE L'EM

ETTEUR

EST INSTALLE D

ANS U

NE ZO

NE D

E LA ZON

E 1. 9. LA TEM

PERATU

RE C

LASSE APPLICABLE D

E L'ÉQU

IPEMEN

T , TEMPER

ATUR

E AMBIAN

TE RAN

GE,

ET MAXIM

UM

PRO

CESSU

S TEMPER

ATUR

E DE L'APPAR

EIL EST CE Q

UI SU

IT ; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°C Ta+71°C 10.LO

RS D

U M

ON

TAGE SU

R U

NE JAU

GE D

E NIVEAU

MAG

NÉTIQ

UE, ASSU

REZ-VO

US Q

UE LA TÊTE ÉLEC

TRO

NIQ

UE ET LA PR

ESSION

BARR

IÈRE A U

N ESPAC

EMEN

T MIN

IMU

M D

E 5 POU

CES. VO

IR LE M

ANU

EL D'IN

STALLATION

POU

R D

ETAIL11.C

HEM

IN D

E FLAM

ME

NE S

ON

T PAS À

RÉ

PAR

ER

(ACP) INSTALLATIO

N D

WG

LP ANALO

G EXPLO

SION

PROO

F CANAD

A

41


Operation Manual


Fig. 46: Explosionproof, FMC Installation Drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651552-2A

1

3 D

RAW

N BY:

MS

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T THE

NO

TIFICA

TION

TO A

PPRO

VAL AG

EN

CY(S).***

AM

S10/24/14

RELEASE TO PRO

DU

CTION

EARTH G

ROU

ND

Rx /Tx-

Rx /Tx+

EARTH G

ROU

ND

COM

MO

N-

24 VDC

EPL Ga

EPL Gb

SEE NO

TE 8

NO

N H

AZARDO

US LO

CATION

HAZARD

OU

S LOCATIO

N

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(CAN

ADA). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERM

INAL

(ACP) INSTALLATIO

N D

WG

LP DIG

ITAL EXPLO

SION

PROO

F CANAD

A

7957

LEVEL

FM

APPROVED

C

N/A

EXPLOSIO

N PRO

OF

CL. I, DIV. 1, G

R. BCD T6...T3

Ex db IIB+H

2 T6...T3 Ga/G

bTa =

-40°C to +71°C ; IP65

FM CAN

ADA- FM

16CA0130XN

OTES:

1.ALL NATIO

NAL AN

D LO

CAL C

OD

ES AN

D R

EGU

LATION

S MU

ST BE AD

HER

ED TO

WH

EN IN

STALLING

THE LEVEL SEN

SOR

IN H

AZARD

OU

S ENVIR

ON

ME

NTS.

FOR

ZON

E INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 50m

m O

F THE

ENC

LOSU

RE. FO

R D

IVISION

INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 18 IN

CH

ES O

F THE EN

CLO

SUR

E.

2.DU

AL-CAVITY EN

CLO

SUR

ES: C

USTO

ME

R C

ON

NE

CTIO

NS W

ILL BE MAD

E AT TERM

INAL BLO

CK O

N PO

WER

SIDE

OF H

OU

SING

(NO

T TO TER

MIN

AL BLOC

K ON

INTER

CO

NN

ECT BO

ARD

). SEE FIGU

RE 2 O

N PAG

E 2

3. CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PR

EVEN

T IGN

ITION

OF FLAM

MA

BLE OR

CO

MBU

STIBLE ATM

OSPH

ERES,

DISC

ON

NE

CT PO

WER

BEFOR

E SER

VICIN

G

5.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK O

F ELECTR

OSTATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC

SUR

FACE AN

D PR

OC

ESS PARTS SH

OU

LD O

NLY

BE C

LEAN

ED W

ITH A D

AMP

CLO

TH. PAIN

TED SU

RFACE OF TH

E EQU

IPMEN

T MAY STO

RE ELECTROSTATIC CH

ARGE

AND

BECOM

E A SOU

RCE OF IG

NITIO

N IN

APPLICATION

S WITH

A LOW

RELATIVE HU

MID

ITY <~

30% RELATIVE

HU

MID

ITY WH

ERE THE PAIN

TED SU

RFACE IS RELATIVELY FREE OF SU

RFACE CO

NTAM

INATIO

N SU

CH AS D

IRT, DU

ST OR

OIL. CLEAN

ING

OF TH

E PAINTED

SURFACE SH

OU

LD O

NLY BE D

ON

E W

ITH A D

AMP CLO

TH.

6. CAB

LES SH

ALL BE

RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) O

R PIPE D

OPE SH

ALL B

E USE

D. R

EFER TO

INSTALLATIO

N IN

STRU

CTIO

NS.

8. THE EQ

UIPM

ENT C

AN BE IN

STALLED IN

THE BO

UN

DAR

Y WALL BETW

EEN A

ZON

E 0 AREA AN

D TH

E LE

SS HAZAR

DO

US AR

EA, ZON

E 1. IN TH

IS CO

NFIG

UR

ATION

, THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED

IN

A ZON

E 0 AR

EA, WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

IN A ZO

NE

1 AR

EA. 9. TH

E APPLICABLE TEM

PER

ATUR

E CLASS O

F THE EQ

UIPM

ENT, AM

BIENT TEM

PER

ATUR

E RAN

GE,

AN

D M

AXIMU

M PR

OC

ESS TEM

PER

ATUR

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CE

SS TEMPER

ATUR

E RAN

GE O

F -40°C to +150°C

T4 WITH

PRO

CE

SS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CE

SS TEMPER

ATUR

E RAN

GE O

F -40°C to +100°C

T6 WITH

PRO

CE

SS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AM

BIE

NT TEM

PERATU

RE R

AN

GE -40°C Ta+71°C

10. WH

EN

MO

UN

TING

ON

A MAG

NE

TIC LE

VEL G

AUG

E M

AKE

SUR

E TH

E ELE

CTR

ON

IC H

EAD

AN

D P

RES

SUR

E

BA

RR

IER H

AVE A

MIN

IMU

M S

PAC

ING

OF 5 IN

CH

ES. SE

E INSTALLATIO

N M

ANU

AL FO

R D

ETA

IL11. FLAM

EP

ATHS

ARE

NO

T FOR

RE

PAIR

CON

DU

IT

CON

DU

IT SEAL

SEE NO

TE 1

CON

DU

IT SEAL

5" [127mm

] Minim

um

42


Operation Manual



DETAIL F

SCALE 1.60 : 1

DETAIL G

SCALE 3 : 1

DETAIL H

SCALE 1.2

F

G

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RATIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-2A

2

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***A

MS

10/24/14RELEASE TO

PROD

UCTIO

N


GND

+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: FO

R ZO

NE IN

STALLATION


STALLED W

ITHIN

50mm

OF TH

E EN

CLO

SUR

E. FOR

DIVISIO

N IN

STALLATION


STALLED W

ITHIN

18 INC

HES O

F THE EN

CLO

SUR

E.

(ACP) INSTALLATIO

N D

WG

LP DIG

ITAL EXPLO

SION

PROO

F CANAD

A


7957

43


Operation Manual



11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651552-2A

3

3 D

RAW

N BY:

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T THE

NO

TIFICA

TION

TO A

PPRO

VAL AG

EN

CY(S).***

A

NO

TES:1. La réglem


RS D

'INSTALLATIO

N D

U C

APTEUR

DE N

IVEAU D

ANS D

ES ENVIR

ON

NEM

ENTS D

ANG

EREU

X. PO

UR

INSTALLATIO

NS D

E ZON

E, UN

SOR

TIE EST INSTALLÉ D

ANS LES 50 m

m D

E L'ENC

EINTE.

POU

R IN

STALLATION

S DE D

IVISION

ALE SOR

TIE EST INSTALLÉ D

ANS LES 18 PO

UC

ES DE L'EN

CEIN

TE2. EN

CEIN

TES à cavité double : Les raccordements clients, seront effectués au bornier d'alim


EMEN

T boîtier (pas au bornier carte d'interconnexion) 3. ATTEN

TION

: LES INSTR

UM

ENTS FLEXIBLES AVEC

UN

RAD

IOD

E MIN

IMU

M D

E 381mm

(15 ")4. ATTEN

TION

: Pour éviter l'inflamm


mables ou com

bustibles, D

ÉBRAN

CH

EZ L'ALIMEN

TATION

AVANT D

'INTER

VENIR

5. AVERTISSEM

ENT: L'ÉQ

UIPEM

ENT C

ON

TENU

E DES PIÈC

ES ET PRO

CÉD

ÉS NO

N-M

ETALLIQU

ES POU

R PR

ÉVENIR

LE RISQ

UE D

'ÉCLAIR

AGE ÉLEC

TRO

STATIQU

E. LA SUR

FACE ET LES PIÈC

ES DE PR

OC

ÉDU

RE N

ON

MÉTALLIQ

UES D

OIVEN

T SEULEM

ENT

EFFECTEZ U

N PAN

NEAU

DE PLAISIR

. LA SUR

FACE PEIN

TÉE DE L'ÉQ

UIPEM

ENT PEU

T CO

NSER

VER LE C

HAR

GE ÉLEC

TRO

STATIQU

E ET D

EVENIR

UN

E SOU

RC

E D'ALLU

MAG

E DAN

S DES APPLIC

ATION

S AVEC U

NE H

UM

IDITÉ BASSE R

ELATIVE <~ 30% R

ELATIVE H

UM

IDITE O

Ù LA SU

RFAC

E PEINTU

RE EST R

ELATIVEMEN

T LIBRE D

E CO

NTAM

INATIO

N D

E SUR

FACE

TELS QU

E LA VIAND

E, LA POU

SSIÈRE O

U L'H

UILE. LE N

ETTOYAG

E DE LA SU

RFAC

E PEINTU

RE D

OIT ÊTR

E FAIT AVEC

UN

PANN

EAU D

E PLAISIR.

6. CABLES doit être évalué> 5C

DESSU

S MAXIM

UM

TEMPER

ATUR

E AMBIAN

TE.7. PO

UR

MAIN

TENIR

LA NO

TATION

DE PR

OTEC

TION

DE IN

GR

ESS IP65, du ruban téflon (3 BAND

ES) ou PIPE DO

PE DEVR

A ÊTRE U

TILISÉ. CO

NSU

LTER LES IN

STRU

CTIO

NS D

'INSTALLATIO

N.

8. L'ÉQU

IPEMEN

T PEUT ÊTR

E INSTALLÉ D

ANS LE M

UR

DE LIM

ITE ENTR

E UN

E ZON

E 0 ET LA ZO

NE M

OIN

S DAN

GER

EUSE, ZO

NE 1. D

ANS C

ETTE CO

NFIG

UR

ATION

, LA CO

NN

EXION

DU

PRO

CESSU

S EST INSTALLEE

DAN

S UN

E ZON

E 0, LOR

SQU

E LE BOITIER

DE L'EM

ETTEUR

EST INSTALLE D

ANS U

NE ZO

NE D

E LA ZON

E 1 9. LA TEM

PERATU

RE C

LASSE APPLICABLE D

E L'ÉQU

IPEMEN

T , TEMPER

ATUR

E AMBIAN

TE RAN

GE,

ET MAXIM

UM

PRO

CESSU

S TEMPER

ATUR

E DE L'APPAR

EIL EST CE Q

UI SU

IT ; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°CTa+71°C10.LO

RS D

U M

ON

TAGE SU

R U

NE JAU

GE D

E NIVEAU

MAG

NÉTIQ

UE, ASSU

REZ-VO

US Q

UE LA TÊTE ÉLEC

TRO

NIQ

UE ET LA PR

ESSION

BARR

IÈRE A U

N ESPAC

EMEN

T MIN

IMU

M D

E 5 POU

CES. VO

IR LE M

ANU

EL D'IN

STALLATION

POU

R D

ETAIL11.C

HEM

IN D

E FLAM

ME N

E SO

NT PA

S À R

ÉPAR

ER

7957RELEASE FO

R PROD

UCTIO

N

(ACP) INSTALLATIO

N D

WG

LP DIG

ITAL EXPLO

SION

PRO

OF CAN

ADA

44


Operation Manual

12.5 ATEX and IECEx


12.5.1.1 Specific conditions of safe use

1. The apparatus enclosure contains aluminum and is considered to constitute a potential risk of ignition by impact or friction. Care must be taken into account during installation and use to prevent impact or friction. ( When installed in a Ga Approval)2. The maximum permitted ambient temperature of the Level Plus® Digital/Analog Level Transmitter is 71 °C. To avoid the effects of process temperature and other thermal effects care shall be taken to ensure the surrounding ambient and the ambient inside the transmitter housing does not exceed 71°C.3. Some models contain non-metallic enclosure parts, to prevent the risk of electrostatic sparking the nonmetallic surface should only be cleaned with a damp cloth.

12.5.1.2 Labels

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES

0.5 0.1




METRIC


1 2

DRAWN BY: NJ

A NJ



FM14ATEX0068XIECEx FMG 14.0032X II 1/2 G Ex ia IIC T4 Ga/Gb Ta = -50°C to +71°C ; IP65when connected in accordancewith FM approved installation drawing # 651543-3




10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE


DATE CODE.


LEVEL

1:1


(ACP) LABEL, LP, IS ATEX/IECEx - DIGITAL

10/24/14

1725


P/N 551629-3 Rev B


R3.30 [.13]

1.78 [.07]

1.78 [.07]

28.70 [1.13]

15.80 [.62]

34.69 [1.37]

86.30 [3.40]

69.85 [2.75]

IP RATING WAS 66 1/19/15NJ7847B

®

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES

0.5 0.1




METRIC


1 2

DRAWN BY: NJ

A NJ



FM14ATEX0068XIECEx FMG 14.0032X II 1/2 G Ex ia IIC T4 Ga/Gb Ta = -50°C to +71°C ; IP65when connected in accordancewith FM approved installation drawing # 651543-3




10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE


DATE CODE.


LEVEL

1:1


(ACP) LABEL, LP, IS ATEX/IECEx - DIGITAL

10/24/14

1725


P/N 551629-3 Rev B


R3.30 [.13]

1.78 [.07]

1.78 [.07]

28.70 [1.13]

15.80 [.62]

34.69 [1.37]

86.30 [3.40]

69.85 [2.75]

IP RATING WAS 66 1/19/15NJ7847B

®

Fig. 49: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, NEMA Housing

Fig. 50: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, NEMA Housing

Fig. 52: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, Single and Dual Cavity Housing

Fig. 51: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, Single and Dual Cavity Housing

651544-3

551641-3

1

1

2

2

A A

B B

TITLE

SIZE DWG NO. REV



0 PLACESMM

1 PLACEMM

ANGLES�� 0.5 � 0.1




METRIC


1 1DRAWN BY: NJ


II 1/2 G Ex ia IIC T4 Ga/GbTa = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNING.


FM14ATEX0068XIECEx FMG 14.0032X

35.05 [1.38]

"L1"∆ "L2"

17.53 [.69]

7.5 POINT SIZE


MTS TO PRINTMODEL NO.


"D1"


12.70 [.50] 3.70 [.15]

(ACP) LABEL, LP, IS ATEX/IECEx - ANALOG

R

1725

�


P/N 551705-X Rev C


LEVEL

1:1


TABLE 1


-1 ADALET85.85 [3.38]

69.85 [2.75]

Ø2.35 [.09]x2

-2 LIMATHERM 65 [2.56] 58 [2.28] Ø 3.05 [.12] x2



1

1

2

2

A A

B B

TITLE

SIZE DWG NO. REV



0 PLACESMM

1 PLACEMM

ANGLES�� 0.5 � 0.1




METRIC


1 1DRAWN BY: NJ



II 1/2 G Ex ia IIC T4 Ga/GbTa = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS



35.05 [1.38]

"L1"∆ "L2"

17.53 [.69]

7.5 POINT SIZE




"D1"


12.70 [.50] 3.70 [.15]

(ACP) LABEL, LP, IS ATEX/IECEX - DIGITAL

R


1725

�


P/N 551703-X Rev C

1:1LEVEL


TABLE 1


-1 ADALET85.85 [3.38]

69.85[2.75]

Ø2.35 [.09]x2

-2 LIMATHERM 65 [2.56] 58 [2.28] Ø 3.05 [.12] x2



45


Operation Manual

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-3

1 2

DR

AWN

BY: M

S

***NO

REV

ISION

S SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO AP

PRO

VAL A

GEN

CY

(S).**

AM

S10/24/14

RELEASE TO PRO

DU

CTION

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 1/19/15

E

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71C MS 2/23/15

D 8037 AD

DED

WIRIN

G CH

ART MS 11/3/15

E 8256 UPD

ATED W

IRING

CHART O

N SH

EET 2 MS 1/30/17

24 VDC

COM

MO

N- >

Rx/Tx+

Rx/Tx -

GRO

UN

D

EARTH G

ROU

ND

(SEE NO

TE 4)

EARTH G

ROU

ND

(SEE NO

TE 4)

Rx/Tx-

Rx/Tx+

GND

+24V

SAFETY BARRIER

SAFETY BARRIER

SAFETY BARRIER

NO

TES

:1.A

LL NA

TION

AL A

ND

LOC

AL C

OD

ES

AN

D R

EGU

LATIO

NS

MU

ST BE

AD

HE

RE

D TO

WH

EN IN

STALLIN

G TH

E LE

VEL SE

NSO

R IN

HA

ZAR

DO

US

EN

VIRO

NM

EN

TS.

SE

AL A

LL CO

ND

UITS W

ITHIN

457 MM

(18"). 2.LO

OP

CAB

LE M

US

T BE 24 AW

G TO

14 AW

G (.511M

M² to 1.6M

M²)

SH

IELDE

D TW

ISTE

D P

AIR

CA

BLE

WITH

SH

IELD. C

ABLE C

AP

ACITA

NC

E M

US

T B

E LE

SS TH

AN

30 pF PER

FOO

T (98 pF PE

R M

). CA

BLE SH

IELD

IS CO

NN

EC

TED

TO SY

STE

M G

RO

UN

D IN

NO

N-H

AZAR

DO

US

AR

EA

. SE

E INS

TALLA

TION

MA

NU

AL FO

R

AD

DITIO

NA

L CAB

LE IN

FOR

MA

TION

. 3.TH

E R

ES

ISTAN

CE

BE

TWEE

N E

ARTH

GR

OU

ND

AND

THE

INTR

INSIC

ALLY

SA

FE GR

OU

ND

MU

ST B

E LESS

THA

N 1 O

HM

. 4.TH

E TR

AN

SD

UC

ER

FRA

ME

SHA

LL BE

GR

OU

ND

ED

TO EA

RTH

GR

OU

ND

DIR

ECTLY

OR

THR

OU

GH

THE

EQU

IPM

EN

T ON

WH

ICH

IT IS M

OU

NTE

D.

5. CO

NTR

OL E

QU

IPM

ENT C

ON

NE

CTE

D TO

AS

SO

CIATE

D A

PPA

RA

TUS

MU

ST

NO

T US

E OR

GE

NE

RATE

MO

RE

THAN

250 VR

MS

OR

VD

C 6.A

SS

OC

IATED

APP

AR

ATUS

MA

NU

FACTU

RE

R'S

INS

TALLA

TION

DR

AW

ING

MU

ST B

E FO

LLOW

ED W

HE

N IN

STA

LLING

THIS

EQU

IPM

EN

T. 7.O

NLY

US

E ATE

X/IE

C A

PP

RO

VED

BAR

RIER

S.

8.EN

TITY PA

RAM

ETE

RS:

S

UPP

LY: R

x/Tx-: Rx/Tx+:

Ui = 28V

DC

Ui= 8.6V

Ui= 8.6V

Ii = 100mA

Ii = 10mA

Ii = 10mA

C

i = 0 µF Ci = 0 µF C

i = 0 µF Li = 0 µH


Pi = 0.7 W

Pi= 0.0215 W

P i= 0.0215 W

9.THE

ENTITY

CO

NC

EPT A

LLOW

S INTE

RC

ON

NE

CTIO

N O

F INTR

INS

ICA

LLY S

AFE

APP

AR

ATU

S W

ITH AS

SO

CIA

TED A

PPA

RA

TUS

WH

EN

THE

FOLLO

WIN

G IS

TRU

E:

V

max or U

i ≥ Voc, V

t or Uo;


Pm

ax or Pi ≥ Po;

Ca ≥ C

i + Ccable;


UAL-C

AVITY

EN

CLO

SU

RE

S: C

US

TOM

ER

CO

NN

EC

TION

S WILL BE

MA

DE AT TE

RM

INA

L BLO

CK

ON

PO

WE

R SID

E O

F HO

US

ING

(NO

T TO TE

RM

INA

L BLO

CK

ON

INTER

CO

NN

EC

T BO

ARD

). 11.FO

R INSTALLATIO

N W

ITHIN

THE EU

ROPEAN

UN

ION

, SEE EN 60079-14.

12.THE

MA

XIM

UM

PER

MITTE

D A

MB

IEN

T TEM

PE

RA

TUR

E O

F THE

LEVE

L PLU

S D

IGITA

L/AN

ALO

G

LEV

EL TR

ANS

MITTE

R IS

71 °C. TO

AV

OID

THE

EFFE

CTS

OF P

RO

CES

S TE

MP

ER

ATU

RE

AN

D

OTH

ER

THE

RM

AL EFFEC

TS CA

RE

SH

ALL BE TA

KE

N TO

ENS

UR

E TH

E S

UR

RO

UN

DIN

G A

MB

IENT

AN

D TH

E AM

BIEN

T INS

IDE

THE

TRAN

SM

ITTER

HO

USIN

G D

OE

S N

OT E

XC

EE

D 71°C

13.CA

UTIO

N: FLE

XIB

LE G

AU

GE

S H

AV

E A M

INIM

UM

BE

ND

DIA

METE

R O

F 406MM

(16") 14.W

AR

NIN

G: TH

E AP

PA

RA

TUS E

NC

LOS

UR

E C

ON

TAIN

S ALU

MIN

UM

AN

D IS C

ON

SID

ER

ED TO

CO

NS

TITUTE

A P

OTE

NTIA

L RIS

K OF IG

NITIO

N B

Y IMP

ACT O

R FR

ICTIO

N. C

ARE

MU

ST BE

TAKE

N

INTO

AC

CO

UN

T DU

RIN

G IN

STA

LLATIO

N A

ND

US

E TO

PR

EVE

NT IM

PAC

T OR

FRIC

TION

15.WA

RN

ING

: SU

BSTITU

TION

OF C

OM

PO

NE

NTS

MA

Y IM

PA

IR IN

TRIN

SIC

SA

FETY

. 16.W

AR

NIN

G: TO

PRE

VEN

T IGN

ITION

OF FLA

MM

AB

LE O

R C

OM

BU

STIBLE

ATM

OS

PH

ERE

S,

DIS

CO

NN

EC

T PO

WE

R BE

FOR

E S

ERV

ICIN

G

17.WA

RN

ING

: THE

EQU

IPM

EN

T CO

NTA

INS N

ON

-ME

TALLIC E

NC

LOS

UR

E PA

RTS, TO

PR

EV

EN

T TH

E R

ISK

OF E

LEC

TRO

STA

TIC SP

AR

KING

. THE

NO

N-M

ETA

LLIC S

UR

FACE

SH

OU

LD O

NLY

B

E C

LEAN

ED

WITH

A DA

MP

CLO

TH.

NO

N H

AZARDO

US LO

CATION

HAZARD

OU

S LOCATIO

N

INTR

INS

ICA

LLY S

AFEFM

14ATE

X0068XIE

CE

x FMG

14.0032X

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERM

INAL

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTR

INSICALLY SAFE FO

R ATEX/IEC

7570

LEVEL

N/A

1725

II 1/2 G Ex ia T4 G

a/Gb

Ta = -50 TO

71°C; IP65


Fig. 53: Intrinsically Safe ATEX / IECEx installation drawing, Modbus and DDA, Page 1

46


Operation Manual


Fig. 54: Intrinsically Safe ATEX / IECEx installation drawing, Modbus and DDA, Page 2

DETAIL A

SCALE 1.60 : 1

DETAIL C

SCALE 3 : 1

DETAIL D

SCALE 1.2

DETAIL E

SCALE 1 : 1

A

C

D

E

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651543-3

2 2

DR

AWN

BY: M

S

***NO

REV

ISION

S SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO AP

PRO

VAL A

GEN

CY

(S).**

AM

S10/24/14

RELEASE TO PRO

DU

CTION

B 7847 UPD

ATED IP RATIN

G FO

R HO

USIN

G TYPES M

S 1/19/15

E

C 7898 UPD

ATED TEM

PERATURE O

N N

OTE 12 TO

71C MS 2/23/15

D 8037 AD

DED

WIRIN

G CH

ART MS 11/3/15

E 8256 UPD

ATED W

IRING

CHART O

N SH

EET 2 MS 1/30/17


GND+24V

TX/RX-TX/RX+EARTH

GND

+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

457 MM

(18") OF H

OU

SING

.

(ACP) INSTALLATIN

DW

G LP D

IGITAL

INTRIN

SICALLY SAFE FOR ATEX/IEC


7570

WIRIN

G CH

ART (FOR N

EMA G

AUG

E)

PIN W

IRING

CHART (FO

R NEM

A GAU

GE)

WIRE CO

LOR

SIGN

ALRED

24 V PWR

BLACK 0 V PW

RBLU

EN

/AW

HITE

RX TX +G

REENRX TX -

DRAIN

WIRE

EARTH G

ROU

ND

PIN #

SIGN

ALPIN

124 V PW

RPIN

20 V PW

RPIN

3N

/APIN

4RX TX+

PIN 5

RX TX-PIN

6EARTH

GRO

UN

D

47


Operation Manual


Fig. 55: Intrinsically Safe ATEX / IECEx installation drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651544-3LEVEL

1 2

DR

AWN

BY: M

S1:1

***NO

RE

VISIO

NS S

HA

LL BE MAD

E WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

EN

CY(S)***

A 7570 R

ELE

ASE TO

PRO

DU

CTIO

N M

S 10/24/14B 7847 U

PDATE

D IP R

ATIN

G FO

R H

OU

SIN

G TYP

E MS

1/19/15C

7898 UP

DA

TED TE

MPE

RA

TUR

E ON

NO

TE 12 TO

71°C M

S 2/23/15D

8037 ADD

ED W

IRIN

G C

HA

RT M

S 11/3/15E 8256 U

PDATED

WIR

ING

CHART O

N SH

EET 2 MS 1/30/17

NO

N H

AZAR

DO

US LO

CATIO

NH

AZAR

DO

US

LOC

ATION

NO

TES:

1. ALL N

ATION

AL AND

LOC

AL CO

DE

S A

ND

RE

GU

LATION

S MU

ST B

E AD

HER

ED TO

WH

EN

INS

TALLING

THE

MTS LP S

ENSO

R IN

HAZA

RD

OU

S EN

VIR

ON

MEN

TS.

SEA

L ALL CO

ND

UITS

WITH

IN 457 M

M (18").

2. LOO

P C

ABLE M

US

T BE 24 A

WG

TO 14 A

WG

(.511MM

² to 1.6MM

²) S

HIE

LDED

TWIS

TED PA

IR C

AB

LE W

ITH SH

IELD. C

ABLE

CA

PAC

ITAN

CE M

US

T B

E LESS

THA

N 30 pF PE

R FO

OT (98 pF P

ER m

). CAB

LE SH

IELD

IS C

ON

NEC

TED

TO S

YSTE

M G

RO

UN

D IN

NO

N-H

AZA

RD

OU

S AR

EA

. SEE

INS

TALLA

TION

MA

NU

AL FO

R

AD

DITIO

NA

L CAB

LE IN

FOR

MA

TION

. 3. TH

E RES

ISTAN

CE

BE

TWE

EN E

ARTH

GR

OU

ND

AND

THE IN

TRIN

SICA

LLY SA

FE GR

OU

ND

MU

ST BE

LESS

THA

N 1 O

HM

. 4. TH

E TR

AN

SD

UC

ER

FRA

ME

SHALL BE

GR

OU

ND

ED TO

EA

RTH

GR

OU

ND

DIR

EC

TLY O

R TH

RO

UG

H TH

E EQ

UIP

ME

NT O

N W

HIC

H IT IS M

OU

NTED

. 5. C

ON

TRO

L EQ

UIPM

EN

T CO

NN

EC

TED

TO AS

SO

CIA

TED

AP

PAR

ATUS M

UST

NO

T US

E O

R G

ENE

RA

TE MO

RE

THA

N 250 VR

MS

OR

VD

C.

6. AS

SOC

IATE

D A

PPAR

ATU

S MAN

UFAC

TUR

ER

'S INS

TALLATIO

N D

RA

WIN

G M

UST

BE

FOLLO

WED

WH

EN

INSTALLIN

G TH

IS EQ

UIP

ME

NT

7. ON

LY U

SE A

TEX/IE

C AP

PR

OVE

D B

ARR

IER

S.

8. AP

PRO

VED

LOO

P SE

PAR

ATION

METH

OD

S: *R

UN

LOO

PS IN

SEP

ARA

TE C

ABLE

S *R

UN

LOO

PS IN

SEP

ARA

TE G

RO

UN

DED

SHIE

LDS

9. EN

TITY PA

RAM

ETERS E

ACH

LOO

P:

Ui = 28 VD

C Ii = 120 m

A C

i = 0 µF Li = 5 µH Pi = 840 m

W 10. D

UA

L-CAV

ITY EN

CLO

SU

RE

S: C

US

TOM

ER

CO

NN

EC

TION

S WILL B

E M

ADE

AT TE

RM

INAL BLO

CK

ON

PO

WER

SIDE

OF H

OU

SING

(NO

T TO TE

RM

INA

L BLO

CK O

N IN

TERC

ON

NEC

T BO

AR

D)

11 FOR

INS

TALLA

TION

WITH

IN TH

E EU

RO

PEA

N U

NIO

N, S

EE E

N 60079-14.

12.THE

MA

XIMU

M P

ERM

ITTED

AM

BIEN

T TEMPE

RATU

RE O

F THE

LEVE

L PLU

S D

IGITAL/A

NA

LOG

LEV

EL TRA

NS

MITTE

R IS 71 °C

. TO A

VOID

THE

EFFE

CTS O

F PR

OC

ESS

TEM

PE

RA

TUR

E AN

D

OTH

ER TH

ERM

AL E

FFECTS C

ARE S

HA

LL BE TA

KEN

TO E

NSU

RE

THE S

UR

RO

UN

DIN

G A

MB

IEN

T A

ND

THE

AMBIE

NT IN

SID

E TH

E TRA

NS

MITTE

R H

OU

SING

DO

ES N

OT E

XCE

ED 71°C

13.CAU

TION

: FLEXIB

LE G

AU

GES

HA

VE A

MIN

IMU

M B

END

RAD

IUS

OF 406M

M (16")

14. WA

RN

ING

: THE

APP

ARATU

S EN

CLO

SUR

E C

ON

TAINS A

LUM

INU

M A

ND

IS CO

NSID

ERED

TO C

ON

STITUTE

A PO

TENTIA

L RISK

OF IG

NITIO

N B

Y IM

PAC

T OR

FRIC

TION

. CAR

E MU

ST B

E TAKEN

IN

TO A

CC

OU

NT D

UR

ING

INS

TALLATIO

N A

ND

US

E TO P

RE

VEN

T IMP

ACT O

R FR

ICTIO

N 15.W

ARN

ING

: SUBS

TITUTIO

N O

F CO

MP

ON

ENTS

MA

Y IMP

AIR IN

TRIN

SIC

SAFETY

. 16.W

ARN

ING

: TO P

REV

ENT IG

NITIO

N O

F FLAM

MAB

LE OR

CO

MB

US

TIBLE A

TMO

SPH

ERES

. D

ISC

ON

NEC

T PO

WER

BEFO

RE S

ERVIC

ING

. 17.W

AR

NIN

G: TH

E EQ

UIP

MEN

T CO

NTA

INS

NO

N-M

ETA

LLIC EN

CLO

SUR

E P

AR

TS, TO

PRE

VEN

T TH

E R

ISK O

F ELE

CTR

OS

TATIC

SPA

RK

ING

. THE

NO

N-M

ETALLIC

SUR

FAC

E S

HO

ULD

ON

LY B

E C

LEA

NE

D W

ITH A

DA

MP

CLO

TH.

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

24 VD

C

CO

NTR

OL

INP

UT 1

CO

NTR

OL

INP

UT 2

APPR

OVE

D SAFETY

BAR

RIER

APPR

OVED

SAFE

TY BA

RR

IER

LOO

P VO

LTAGE

SHIE

LD

SH

IELD

LOO

P 1+

LOO

P 1-

LOO

P 2+

LOO

P 2-

US

(ACP) INSTALLATIN

DW

G LP AN

ALOG

INTR

INSICALLY SAFE FO

R ATEX/IEC

SIN

GLE

OR

DU

AL C

AVITY

NEM

A H

OU

SIN

G

E

II 1/2 G Ex ia T4 G

a/Gb

Ta = -50 TO

71°C; IP65

INTR

INS

ICA

LLY S

AFE

FM14ATE

X0068X

IEC

Ex FMG

14.0032X

1725

EAR

TH G

RO

UN

D

(SEE N

OTE

4)

EARTH

GR

OU

ND

(S

EE NO

TE 4)

48


Operation Manual


Fig. 56: Intrinsically Safe ATEX / IECEx installation drawing, HART®, Page 2

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETA

IL FSC

ALE 1.2

DETAIL H

SCALE 1 : 1

D

E

F

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651544-3LEVEL

2 2

DR

AWN

BY: M

S1:1

***NO

RE

VISIO

NS S

HA

LL BE MAD

E WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

EN

CY(S)***

A 7570 R

ELE

ASE TO

PRO

DU

CTIO

N M

S 10/24/14B 7847 U

PDATE

D IP R

ATIN

G FO

R H

OU

SIN

G TYP

E MS

1/19/15C

7898 UP

DA

TED TE

MPE

RA

TUR

E ON

NO

TE 12 TO

71°C M

S 2/23/15D

8037 ADD

ED W

IRIN

G C

HA

RT M

S 11/3/15E 8256 U

PDATED

WIR

ING

CHART O

N SH

EET 2 MS 1/30/17

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER

SHO

ULD

CO

NN

ECT TH

E OU

TSID

E GR

OU

ND

LUG

TO TH

E SAFE

TY EAR

THIN

G G

RO

UN

D SYS

TEM W

ARN

ING

: C

ON

DU

IT SEALS R

EQ

UIR

ED

WITH

IN 457 M

M (18") O

F HO

USIN

G.

FIGU

RE 2

DU

AL CAV

ITY HO

USIN

G


FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING


(AC

P) INSTALLA

TION

DW

G LP

ANALG

O

INTR

INSIC

ALLY SA

FE ATEX/IEC

E


E

WIRIN

G CH

ART( FOR N

EMA G

AUG

E)

PIN W

IRING

CHART (FO

R NEM

A GAU

GE)

WIRE CO

LOR

SIGN

ALRED

LOO

P 1+BLACK

LOO

P 1-BLU

ELO

OP 2-

WH

ITELO

OP 2+

GREEN

N/A

DRAIN

WIRE

EARTH G

ROU

ND

PIN #

SIGN

ALPIN

1LO

OP 1-

PIN 2

LOO

P 1+PIN

3LO

OP 2-

PIN 4

LOO

P 2+PIN

5N

/APIN

6EARTH

GRO

UN

D

49


Operation Manual

12.5.2.2 Labels


Fig. 57: Flame Proof, ATEX and IECEx label, Modbus or DDA Housing Option D, E, G, H, or L

Fig. 58: Flame Proof, ATEX and IECEx label, HART®, Housing Option D, E, G, H, or L

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METR IC

FIRST ANGLE A 551707-X A

1 1

DRAWN BY: MS



Level Plus TransmitterMTS Systems CorporationSensors Division3001 Sheldon Drive, Cary, N.C. 27513 U.S.A

�

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS

MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)

INSTALL PER DRAWING # 651552-3

II 1/2 G Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP65 INPUT: 28V (120mA) maxOUTPUT: RS485

38.00 [1.50]

"L1"

∆ "L2"

19.00 [.75]

4.2 POINT SIZE



REFER TO DRAWING# 280743

SERIAL NO./DATE CODE"D1"


(ACP) LABEL, LP, XP ATEX/IECEx - DIGITAL

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.3. ∆ INDICATES CRITICAL DIMENSIONS.4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES5. MATERIAL: .8 [.03] THICK ALUMINUM.6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.

1725

P/N 551707-X Rev A

1:1

LEVEL



CE LOGO TO BE 5mm MINIMUM

TABLE 1DASH

# HOUSING GROUPS "L1" "L2" "D1"

-1ADALET [403892, 403890,403889]

B,C,D85.85 [3.38]

69.85 [2.75]

Ø2.35 [.09]x2

-2LIMATHERM

[403812, 403813]A,B,C,D

65 [2.56]

58 [2.28]Ø 3.05 [.12] x2

!

R

7. POINT TEXT SIZE

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES� � �� 0.5 � 0.1




METR IC


1 1

DRAWN BY: MS



Level Plus TransmitterMTS Systems CorporationSensors Division3001 Sheldon Drive, Cary, N.C. 27513U.S.A

�

II 1/2 G Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP65 INPUT: 28V (120mA) maxOUTPUT: 4-20mA

MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)

INSTALL PER DRAWING # 651553-3

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS

38.00 [1.50]

"L1"

∆ "L2"

19.00 [.75]

4.2 POINT SIZE


MTS TO PRINT

MODEL NO.REFER TO DRAWING #280743


"D1"


(ACP) LABEL, LP, XP ATEX/IECEx - ANALOG

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.3. ∆ INDICATES CRITICAL DIMENSIONS.4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES5. MATERIAL: .8 [0.03] THICK ALUMINUM.6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.

1725

P/N 551709- Rev A

1:1

LEVEL



CE LOGO TO BE 5mm MINIMUM

TABLE 1DASH

# HOUSING GROUPS "L1" "L2" "D1"

-1ADALET [403892, 403890,403889]

B,C,D85.85 [3.38]

69.85 [2.75]

Ø2.35 [.09]x2

-2LIMATHERM

[403812, 403813]A,B,C,D

65 [2.56]

58 [2.28]Ø 3.05 [.12] x2

!

R

7. POINT TEXT SIZE



1. Warning: The equipment contains non-metallic enclosure and process parts, to prevent the risk of electrostatic sparking. The non-metallic surface should only be cleaned with a damp cloth. Painted surface of the equipment may store electrostatic charge and become a source of ignition in applications with a low relative humidity <~30% relative humidity where the painted surface is relatively free of surface contamination such as dirt, dust or oil. Cleaning of the painted surface should only be done with a damp cloth.2. Cables shall be rated > 5°C above maximum ambient temperature.3. To maintain the ingress protection rating of IP65, Teflon tape (3 wraps) or pipe dope shall be used. Refer to Installation Instructions.4. Equipment can be installed in a boundary wall configuration where the process connection is installed as Category 1G equipment while the transmitter housing is installed as Category 2G equipment. Refer to installation instructions.5. Flexible gauges have a minimum bend radius of 381 mm (15 inches).6. Flamepaths not for repair.7. The applicable temperature class, ambient temperature range and process temperature range of the equipment is as follows:



50


Operation Manual


Fig. 59: Flame Proof, ATEX and IECEx Installation Drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651553-3A

LEVEL1

2

DR

AWN

BY: M

S1:1

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T NO

TIFICATIO

N TO

APPR

OV

AL AG

ENC

Y(S

)***A

7957 RE

LEAS

E TO PR

OD

UC

TION

MS 10/22/15

EARTH G

RO

UN

D

Rx /Tx-

Rx /Tx+

EARTH G

ROU

ND

COM

MO

N-

24 VDC

NO

N H

AZAR

DO

US LO

CATIO

NH

AZAR

DO

US LO

CATIO

N

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

(ACP) INSTALLATIO

N D

WG

LP ANALO

G EXPLO

SION

PROO

F ATEX/IEC

SING

LE OR

DU

AL CAV

ITY

1725For ATEX - FM

16ATEX0068XFor IECEx - IECEx FM

G 16.0033X

AR

EA R

EQ

UIR

ING

E

PL Gb

AREA

REQ

UIR

ING

EP

L Ga

CO

ND

UIT JU

NC

TION

CO

ND

UIT

SEE NO

TE 1

SEE NO

TE 8

II 1/2 G

Ex db IIB+H

2 T6...T3 Ga/G

bTa =

-40°C to +71°C; IP65

CA

TEGO

RY 1

CA

TEGO

RY

2

NO

TES:

1.ALL N

ATIO

NAL AN

D LO

CAL C

OD

ES

AND

REG

ULA

TION

S MU

ST BE A

DH

ERED

TO W

HEN

INSTA

LLING

THE

LEVE

L SEN

SO

R IN

HA

ZAR

DO

US EN

VIR

ON

ME

NTS.

SEA

L ALL C

ON

DU

ITS W

ITHIN

50mm

OF EN

CLO

SUR

E.

2.DU

AL-C

AVITY

ENC

LOS

UR

ES:

CU

STOM

ER

CO

NN

ECTIO

NS

WILL B

E MAD

E AT TE

RM

INA

L BLO

CK O

N P

OW

ER

SIDE

OF H

OU

SIN

G (N

OT TO

T ERM

INAL BLO

CK

ON

INTER

CO

NN

ECT B

OA

RD

). SEE

FIGU

RE 2 O

N P

AG

E 2

3. CA

UTIO

N: FLE

XIBLE

GA

UG

ES H

AVE

A MIN

IMU

M BE

ND

RA

DIU

S O

F 381mm

(15")4.W

ARN

ING

: TO P

REV

EN

T IGN

ITION

OF FLA

MM

ABLE O

R C

OM

BU

STIBLE

ATM

OS

PHER

ES,

DISC

ON

NE

CT PO

WER

BEFO

RE

SER

VICIN

G

5.WAR

NIN

G: TH

E EQ

UIPM

ENT C

ON

TAINS N

ON

-ME

TALLIC EN

CLO

SUR

E A

ND

PRO

CE

SS P

ARTS

, TO P

RE

VEN

T TH

E R

ISK O

F ELEC

TRO

STA

TIC S

PAR

KING

. THE

NO

N-M

ETA

LLIC SU

RFA

CE AN

D P

RO

C ESS PA

RTS S

HO

ULD

ON

LY

BE C

LEAN

ED

WITH

A D

AM

P C

LOTH

. PAINTED

SURFACE O

F THE EQ

UIPM

ENT M

AY STORE ELECTRO

STATIC CHARG

E AN

D BECO

ME A SO

URCE O

F IGN

ITION

IN APPLICATIO

NS W

ITH A LO

W RELATIVE H

UM

IDITY <

~30%

RELATIVE H

UM

IDITY W

HERE TH

E PAINTED

SURFACE IS RELATIVELY FREE O

F SURFACE CO

NTAM

INATIO

N SU

CH AS D

IRT, DU

ST OR O

IL. CLEANIN

G O

F THE PAIN

TED SU

RFACE SHO

ULD

ON

LY BE DO

NE

WITH

A DAM

P CLOTH

.6. C

ABLES

SHALL BE

RATE

D > 5C

ABO

VE

MAX

IMU

M AM

BIEN

T TEMPE

RATU

RE

. 7. TO

MA

INTAIN

THE IN

GR

ESS

PR

OTE

CTIO

N R

ATING

OF IP

65, TEFLO

N TAP

E (3 WR

APS

) OR

PIPE

DO

PE S

HALL

BE

USE

D. R

EFER

TO IN

STALLATIO

N IN

STR

UC

TION

S.8. TH

E EQ

UIP

ME

NT C

AN BE

INS

TALLE

D IN

THE

BO

UN

DAR

Y W

ALL BE

TWEE

N A

N EP

L Ga A

RE

A AN

D TH

E

LESS H

AZARD

OU

S A

REA

, EPL G

b. IN TH

IS C

ON

FIGU

RATIO

N, TH

E PR

OC

ESS

CO

NN

ECTIO

N IS

INS

TALLED

IN EP

L Ga, W

HILE

THE

TRAN

SM

ITTER H

OU

SING

IS IN

STA

LLED IN

EPL G

b. RE

FER TO

INS

TALLATION

IN

STRU

CTIO

NS

. E

QU

IPMEN

T CA

N B

E INS

TALLED IN

A BOU

ND

AR

Y WALL C

ON

FIGU

RATIO

N W

HER

E THE

PRO

CE

SS C

ON

NEC

TION

IS IN

STALLED

AS

CATE

GO

RY

1G EQ

UIP

ME

NT W

HILE TH

E TR

ANSM

ITTER

HO

USIN

G IS IN

STALLED

AS

CA

TEGO

RY 2G

EQU

IPM

EN

T. REFE

R TO

INSTA

LLATIO

N IN

STRU

CTIO

NS

9. THE

APPLIC

ABLE

TEMPE

RATU

RE

CLA

SS O

F THE E

QU

IPMEN

T, AM

BIEN

T TEM

PER

ATU

RE R

AN

GE,

AN

D M

AXIM

UM

PRO

CE

SS TEM

PE

RATU

RE

OF TH

E E

QU

IPME

NT IS

AS FO

LLOW

S;

T3 WITH

PR

OC

ESS TE

MP

ERA

TUR

E RAN

GE

OF -40°C

to +150°C T4 W

ITH P

RO

CES

S TEM

PER

ATU

RE R

ANG

E O

F -40°C to +135°C

T5 WITH

PR

OC

ESS TE

MP

ERA

TUR

E RAN

GE

OF -40°C

to +100°C T6 W

ITH P

RO

CES

S TEM

PER

ATU

RE R

ANG

E O

F -40°C to +85°C

AM

BIEN

T TEM

PER

ATU

RE R

ANG

E -40°C Ta+71°C

10. WH

EN

MO

UN

TING

ON

A M

AG

NE

TIC LE

VEL G

AUG

E M

AKE

SUR

E THE

ELECTR

ON

IC H

EAD

AND

PRE

SSU

RE

B

AR

RIER

HAV

E A M

INIM

UM

SP

ACIN

G O

F 5 INC

HES

. SEE

INSTA

LLATIO

N M

AN

UAL FO

R D

ETAIL11. FLAM

EPATH

S AR

E N

OT FO

R R

EPAIR

5" [127mm

] Minim

um

51


Operation Manual


Fig. 60: Flame Proof, FM Installation Drawing, Modbus and DDA

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

D

E

F

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RATIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-3A

LEVEL2

2

DR

AWN

BY: D

R

1:1

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T NO

TIFICATIO

N TO

APPRO

VAL AGEN

CY(S)***

A 7957 RELEASE TO

PRO

DU

CTIO

N M

S 10/22/15

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

50mm

OF H

OU

SING

.

FIGU

RE 2

DU

AL CAVITY H

OU

SING


FIGU

RE 1

SING

LE CAVITY H

OU

SING


(ACP) INSTALLATIO

N D

WG

LP ANALO

G EXPLO

SION

PROO

F ATEX/IEC

52


Operation Manual


Fig. 61: Flame Proof, ATEX and IECEx Installation Drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

EC

O #

DESC

RIP

TION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LES

S OTH

ER

WISE

SPEC

IFIED

TOLER

ANC

ES0 P

LACE

SM

M1 PLA

CE

MM

AN

GLE

S

0.5

0.1

- THR

EA

D D

EP

THS

AR

E TO

MIN

. FULL TH

DS

- DR

ILL DE

PTH

S A

RE

TO FU

LL DIA

.- R

EM

OV

E B

UR

RS

AN

D S

HA

RP

ED

GE

S- D

O N

OT S

CA

LE P

RIN

T- M

AC

HIN

ED

SU

RFA

CE

FINIS

H 3.2uM

[125 uIn]

PRO

PRIETA

RY D

ATA

THE

INFO

RM

ATIO

N A

ND

DE

SIG

N(S

) DIS

CLO

SE

DH

ER

EIN

AR

E TH

E P

RO

PE

RTY

OF M

TS S

YS

TEM

SC

OR

PO

RA

TION

AN

D M

AY

NO

T BE

US

ED

,R

EP

RO

DU

CE

D O

R D

ISC

LOS

ED

IN A

NY

FOR

ME

XC

EP

T AS

GR

AN

TED

IN W

RITIN

G B

Y M

TSS

YS

TEM

S C

OR

PO

RA

TION

. THIS

RE

STR

ICTIO

NE

XC

LUD

ES

INFO

RM

ATIO

N TH

AT IS

IN TH

E

PU

BLIC

DO

MA

IN O

R W

AS

LEG

ITIMA

TELY

IN TH

EP

RIO

R P

OS

SE

SS

ION

OF TH

E R

EC

IPIE

NT.

mM

TS SYS

TEMS

CO

RP

OR

ATIO

NS

ENSO

RS D

IVISIO

N3001 SH

ELDO

N D

RIVE

, CA

RY, N

C 27513

METRIC

FIRST

ANG

LED

651552-3A

1

2 D

RAW

N BY:

MS

***NO

RE

VISION

S SHALL BE

MA

DE

WITH

OU

T THE

NO

TIFICA

TION

TO A

PPRO

VAL AG

EN

CY(S).***

AM

S10/24/14

RELEASE TO PRO

DU

CTION

EARTH G

ROU

ND

24 VDC

COM

MO

N-

Rx /Tx+

Rx /Tx-

EARTH G

ROU

ND

CATEGO

RY 1

CATEGO

RY 2

NO

N H

AZARDO

US LO

CATION

HAZARD

OU

S LOCATIO

N

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERM

INAL

(ACP) INSTALLATIN

DW

G LP D

IGITAL

EXPLOSIO

N PRO

OF ATEX/IEC

7957

LEVEL

N/A

1725II 1/2 G

Ex db IIB+

H2 T6...T3 G

a/Gb

Ta = -40°C to +

71°C; IP65

For ATEX - FM16ATEX0068X

For IECEx - IECEx FMG 16.0033X

AREA REQ

UIRIN

GEPL G

b

AREA REQU

IRING

EPL Ga

NO

TES:

1.ALL NA

TION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERE

D TO

WH

EN

INSTALLIN

G TH

E LEVEL SEN

SOR

IN H

AZARD

OU

S ENVIR

ON

MEN

TS. SEAL ALL C

ON

DU

ITS WITH

IN 50m

m O

F ENC

LOSU

RE.

2.DU

AL-CAV

ITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE

MAD E AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D). SEE FIG

UR

E 2 ON

PAGE 2

3. CA

UTIO

N: FLEXIBLE G

AUG

ES H

AVE A M

INIM

UM

BEND

RAD

IUS

OF 381m

m(15")

4.WAR

NIN

G: TO

PREV

ENT IG

NITIO

N O

F FLAMM

ABLE OR

CO

MBU

STIBLE ATMO

SPH

ERES,

DISC

ON

NEC

T POW

ER BEFO

RE SE

RVIC

ING

5.W

ARN

ING

: THE EQ

UIPM

ENT C

ON

TAINS N

ON

-METALLIC

ENC

LOS

UR

E AND

PRO

CESS PA

RTS, TO

PREVEN

T TH

E RIS

K OF ELEC

TRO

STATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC SU

RFAC

E AND

PRO

CESS PAR

TS S

HO

ULD

ON

LY BE C

LEAN

ED W

ITH A D

AMP C

LOTH

. PAINTED

SURFACE O

F THE EQ

UIPM

ENT M

AY STORE ELECTR

OSTATIC CH

ARGE

AND

BECOM

E A SOU

RCE OF IG

NITIO

N IN

APPLICATION

S WITH

A LOW

RELATIVE H

UM

IDITY <

~30%

RELATIVE H

UM

IDITY W

HER

E THE PAIN

TED SU

RFACE IS RELATIVELY FR

EE OF SU

RFACE CO

NTAM

INATIO

N SU

CH AS D

IRT, DU

ST OR O

IL. CLEANIN

G O

F THE PAIN

TED SU

RFACE SHO

ULD

ON

LY BE DO

NE

WITH

A DAM

P CLOTH

.6. C

ABLES SH

ALL BE R

ATED > 5C

ABOVE M

AXIMU

M A

MB

IEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN

THE IN

GR

ESS PRO

TEC

TION

RATIN

G O

F IP65, TEFLO

N TAPE

(3 WR

APS) O

R PIPE D

OPE SH

ALL BE U

SED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE IN

STALLED IN

THE BO

UN

DA

RY W

ALL BETWEEN

AN EPL G

a AR

EA AND

THE

LESS HA

ZARD

OU

S AR

EA, EPL G

b. IN TH

IS CO

NFIG

UR

ATION

, THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED

IN EPL G

a, WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

IN EPL G

b. REFE

R TO

INSTALLATIO

N

INSTR

UC

TION

S. EQ

UIPM

ENT C

AN BE IN

STALLED

IN A BO

UN

DAR

Y WALL C

ON

FIGU

RATIO

N W

HER

E THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED A

S CATEG

OR

Y 1G EQ

UIPM

ENT W

HILE TH

E TRAN

SMITTER

HO

USIN

G IS IN

STALLED

AS C

ATEGO

RY 2G

EQU

IPMEN

T. REFER

TO IN

STALLATION

INSTR

UC

TION

S. 9. TH

E APPLICABLE TE

MP

ERATU

RE C

LASS OF TH

E EQU

IPMEN

T, AMBIEN

T TEM

PER

ATUR

E RAN

GE,

AND

MAXIM

UM

PRO

CESS TEM

PER

ATUR

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C Ta+71°C

10. WH

EN M

OU

NTIN

G O

N A

MAG

NETIC

LEVEL G

AUG

E MAKE SU

RE

THE ELEC

TRO

NIC

HEAD

AN

D PR

ESSUR

E BAR

RIER

HA

VE A MIN

IMU

M SP

ACIN

G O

F 5 INC

HE

S. SEE INSTALLATIO

N M

ANU

AL FOR

DE

TAIL11. FLAM

EPATHS

ARE N

OT FO

R R

EPAIR

SEE NO

TE 8

CON

DU

IT SEALCON

DU

IT

SEE NO

TE 1

5" [127mm

] Minim

um

53


Operation Manual


Fig. 62: Flame Proof, ATEX and IECEx Installation Drawing, HART®, Page 2

DETAIL A

SCALE 1.60 : 1

DETAIL C

SCALE 3 : 1

DETAIL D

SCALE 1.2

A

C

D

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RATIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-3A

2

2 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***A

MS

10/24/14RELEASE TO

PROD

UCTIO

N


GND

+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY H

OU

SING

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

50mm

OF H

OU

SING

.


7957

(ACP) INSTALLATIO

N D

WG

LP DIG

ITAL EXPLO

SION

PROO

F ATEX/IEC

54


Operation Manual

LOCA

TION

S

LEGA

L NO

TICE

SUSA MTS Systems CorporationSensors Division3001 Sheldon DriveCary, N.C. 27513, USATel. +1 919 677-0100Fax +1 919 [email protected]

JAPANMTS Sensors Technology Corp.737 Aihara-machi, Machida-shi, Tokyo 194-0211, JapanTel. + 81 42 775-3838Fax + 81 42 775- [email protected]

FRANCEMTS Systems SASZone EUROPARC Bâtiment EXA 1616/18, rue Eugène Dupuis94046 Creteil, FranceTel. + 33 1 58 4390-28Fax + 33 1 58 [email protected]

GERMANYMTS Sensor TechnologieGmbH & Co. KGAuf dem Schüffel 958513 Lüdenscheid, GermanyTel. + 49 2351 9587-0Fax + 49 2351 [email protected]

CHINAMTS Sensors Room 504, Huajing Commercial Center, No. 188, North Qinzhou Road200233 Shanghai, ChinaTel. +86 21 6485 5800 Fax +86 21 6495 [email protected]

ITALYMTS Systems Srl.Sensor DivisionVia Camillo Golgi, 5/725064 Gussago (BS), ItalyTel. + 39 030 988 3819Fax + 39 030 982 [email protected]

MTS, Temposonics and Level Plus are registered trademarks of MTS Systems Corporationin the United States; MTS SENSORS and the MTS SENSORS logo are trademarks of MTSSystems Corporation within the United States. These trademarks may be protected in othercountries. All other trademarks are the property of their respective owners.Copyright © 2018 MTS Systems Corporation. No license of any intellectual propertyrights is granted. MTS reserves the right to change the information within this document,change product designs, or withdraw products from availability for purchase withoutnotice. Typographic and graphics errors or omissions are unintentional and subject tocorrection. Visit www.mtssensors.com for the latest product information.

12.5.3 EC Declaration of Conformity

55

Document Part Number: 551690 Revision C (EN) 2/2018

LOCA

TION

S

LEGA

L NO

TICE

SUSA MTS Systems CorporationSensors Division3001 Sheldon DriveCary, N.C. 27513, USATel. +1 919 677-0100Fax +1 919 [email protected]

JAPANMTS Sensors Technology Corp.737 Aihara-machi, Machida-shi, Tokyo 194-0211, JapanTel. + 81 42 775-3838Fax + 81 42 775- [email protected]

FRANCEMTS Systems SASZone EUROPARC Bâtiment EXA 1616/18, rue Eugène Dupuis94046 Creteil, FranceTel. + 33 1 58 4390-28Fax + 33 1 58 [email protected]

GERMANYMTS Sensor TechnologieGmbH & Co. KGAuf dem Schüffel 958513 Lüdenscheid, GermanyTel. + 49 2351 9587-0Fax + 49 2351 [email protected]

CHINAMTS Sensors Room 504, Huajing Commercial Center, No. 188, North Qinzhou Road200233 Shanghai, ChinaTel. +86 21 6485 5800 Fax +86 21 6495 [email protected]

ITALYMTS Systems Srl.Sensor DivisionVia Camillo Golgi, 5/725064 Gussago (BS), ItalyTel. + 39 030 988 3819Fax + 39 030 982 [email protected]

MTS, Temposonics and Level Plus are registered trademarks of MTS Systems Corporationin the United States; MTS SENSORS and the MTS SENSORS logo are trademarks of MTSSystems Corporation within the United States. These trademarks may be protected in othercountries. All other trademarks are the property of their respective owners.Copyright © 2018 MTS Systems Corporation. No license of any intellectual propertyrights is granted. MTS reserves the right to change the information within this document,change product designs, or withdraw products from availability for purchase withoutnotice. Typographic and graphics errors or omissions are unintentional and subject tocorrection. Visit www.mtssensors.com for the latest product information.

S a f e t y I n t e g r i t y L e v e lIEC 61508

Documents

Magnetostrictive Liquid Level Transmitters with Temposonics · 2018-04-11 · ‘Generalized Crude Oils’, Correction of Volume to 60 °F against API . Gravity. 6B Light Oils ‘Generalized