Upload
nguyendieu
View
265
Download
0
Embed Size (px)
Citation preview
Magnum IV Control
Wiring & Adjustment Manual
for
Gyro Tech Swing Door Operators
Part Number 15-10682 3-12-10 Revision
NABCO ENTRANCES Inc. S82 W18717 Gemini Drive
Muskego, WI 53150 Phone: 877-622-2694 Fax: 888-679-3319
Technical Assistance: 866-622-8325 www.nabcoentrances.com
Email: [email protected]
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 2 www.NabcoEntrances.com 3/12/10
CAUTION
Read these safety practices before installing, operating or servicing the automatic door. Failure to follow these practices may result in serious consequences. Read, study and understand the operating instructions contained in or referenced in this manual before operating. If you do not understand the instruction, ask the installing qualified technician to teach you how to use the door. This manual and the owners’ manual must be given to and retained by the purchasing facility or end user. If the door appears broken or does not seem to work correctly, it should be immediately removed from service and a qualified service technician contacted for corrective action. Disconnect power at the fused disconnect during all electrical or mechanical service. When uncertain whether power supply is disconnected, always verify using a voltmeter. All electrical troubleshooting or service must be performed by qualified electrical technicians and must comply with all applicable governing agency codes. It is the responsibility of the installing door technician to install all warning and instructional labels in accordance with the applicable ANSI standard. It is the responsibility of the purchasing facility or end user to keep warning and instructional labels and literature legible, intact and with the door. Replacement labels and literature may be obtained from local NABCO ENTRANCES INC. authorized distributors. If the name of the local distributor is unknown, contact NABCO ENTRANCES INC. at (877-622-2694) for assistance. Do not place finger or uninsulated tools inside the electrical control box. Touching wires or other parts inside the enclosure may cause electrical shock, serious injury or death. All adjustments should be made with a small screwdriver. DO NOT use a pencil. The ground wire from the Magnum 120 VAC harness and the ground wire from the 120 VAC “in” line must be attached to the ground screw which is located in the header. Final installation must conform to current versions of ANSI 156.19 for Low Energy swingers or ANSI 156.10 for Full Automatic Installations.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 3 www.NabcoEntrances.com 3/12/10
Table of Contents
To The Installer Page 4
Overview Page 4
Specifications Page 5
Visual Indicators Page 5
Magnum IV Diagnostic LED Function Chart Page 6
Wiring Connectors Page 7-8
Door Positions Page 8
Adjustments Page 9
Potentiometers Page 9-11
Dip Switches Page 11
Troubleshooting Page 12-13
Section A - Wiring and Adjustment for GT-300, GT-400 and GT-500 Operators Page 14
Back Check and Latch Micro Switches Page 14
Required Wiring Harnesses Page 15
Wiring for Rocker switch Page 16
Wiring for Break–out Page 16
General Wiring - Single Diagram Page 17
General Wiring – Simultaneous Pair Page 18
Section B - Retrofit Kit Manual, Model 300/400/500 Swing Door System With Magnum IV Control Page 19
Tools required Page 19
Hard Ware Kit List Page 20
Conversion of a GT300/400/500 to a Magnum IV Page 21-23
General Wiring - Single Diagram Page 24
General Wiring – Simultaneous Pair Page 25
Section C - Wiring and Adjustment for GT-710 Operators Page 26
General Wiring Diagram - Single Door Page 27
Wiring Diagram for Wall Switch Activation Page 28
Wiring Diagram for Simultaneous Pairs Page 29
Transformer Installation and Wiring for 240 Volts Page 30
Wiring Diagram for Radio Activation using Linear Receiver Page 31
Wiring Diagram for 4 Wire Radio Receiver and Electric Strike Page 33
Wiring Diagram for Electric Strike and Fire Alarm Systems Page 34
Wiring Diagram for Radio Activation using Clear Path Receiver Page 32
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 4 www.NabcoEntrances.com 3/12/10
LED
TRANSFORMER
CAPACITOR
OFF
12
AUXPWR
4
J2
3
J5
AC IN
F2
SW2SW1
F1
RELAY RELAY
J4
TDAS
SIGNALINPUT
TDPG
LCHK
CLOSE
Fuse 1: 0.5A 24 VAC
STOP
OPEN
BCHK
CURRENTLIMIT
MOTOR
J1
R28
MAGNUM IVFuse 2: 5A 120/240
DN0033
BLACK
RED
To The Installer The purpose of this manual is to familiarize the purchaser with the proper installation and operation of this system. It is essential that this equipment be properly installed and operational before the door is used by the public. It is the purchaser’s responsibility to inspect the operation of the entrance system to be sure it complies with any applicable standards. In the United States, ANSI Standard 156.19 usually covers this type of door. Other local standards or codes may apply. Use them in addition to the ANSI Standard.
Instruct the building owners/operator on the essentials of the operation of the door and
this device. The owner should follow these instructions to determine whether the door is operating properly and should immediately call for service if there is any malfunction.
All installation changes and adjustments must be made by qualified, NABCO trained
technicians. Overview Earlier versions of Gyro Tech GT300, GT400, GT500 and GT710 Swing Door
Operators can be retrofitted with the newer Magnum IV Control Board. This combination offers several control features that accommodate most installations.
Some features of the Magnum IV Board include:
A. Two safety inputs: 1. A safety with a built in internal lockout 2. A continuous safety input that is always active B. Sequential or Timer Mode operation C. Multifunction diagnostic LED’s that indicate what the Magnum control is
doing at all times D. Push-N-Go feature E. Adjustable potentiometer to govern whether the door stops, creeps open or
closes when the continuous safety is activated F. 24 VAC 0.5 Amp output for auxiliary devices G. Close on Obstruction feature that is adjustable via a “Current Limit”
potentiometer H. A two position slide switch that permits the installer to choose Low Energy or
Full Automatic mode of operation I The versatility to use the Magnum IV with either a hydraulic closer with built
in braking (such as the GT-710) or a spring close mechanical closer with no built in braking. With the latter, the Magnum IV provides the braking for the closer via a braking module as is used with the GT300/400/500
FIGURE 1 – OVERVIEW OF MAGNUM IV & BRAKING MODULE (BRAKING MODULE NOT USED ON GT-710)
Braking module not used on GT-710
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 5 www.NabcoEntrances.com 3/12/10
Specifications:
Power Input 120 VAC (±10%) AC 50-60 Hz, 5 Amps
Available Output for Accessories 0.5 Amps 24 Volts AC
Available Wire Size for Incoming Power 14 AWG
1 x 120 VAC 5A Glass Fuse
1 x 24 VAC non-replaceable
Thermo-Couple Automatic cutoff of motor if overheated
Opening Hold Time Adjustable 0-60 seconds
Fuses
Visual Indicators:
The Magnum IV control is equipped with two diagnostic LED’s that enable the technician to directly observe what the Magnum control is reacting to at any instant in the door cycle. This feature compliments the use of the optional Gyro Tech Diagnostic Daughter Board (P/N 14-10597) tool (see below) that provides visual indication of the signals the Magnum control is receiving , at any instant in the door cycle. The Diagnostic Daughter Board can be ordered from Customer Service. It is a valuable tool that provides a quick visual indication of signals being received by the control and is also compatible with earlier models of Magnum controls.
These two indicators, the Magnum LEDs and the Diagnostic Daughter Board LEDs, are designed to work in tandem to enable the technician to easily adjust the Magnum IV control or troubleshoot a problem installation. NABCO ENTRANCES strongly recommends the use of the optional Diagnostic Daughter Board to assist the technician when installing or servicing the Magnum IV control.
The two LED’s on the Magnum IV control are RED and GREEN. The GREEN LED is a cycle status indicator. This LED indicates the status of the door at any instant in the door cycle. The RED LED is the safety status indicator. This LED indicates the state of the two safety signals or the state of the Recycle on Obstruction (Current Limit) at any instant in the door cycle. On the next page is a table that outlines the signals of the two LED’s.
Magnum Diagnostic Daughter Board
PN 14-10597
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 6 www.NabcoEntrances.com 3/12/10
Magnum IV Diagnostic LED Function Chart
LED Color Door Status LED Status Explanation
GreenClosed Off
Magnum is not activated, door is in Latch Check areaOpening Fast Flash Magnum is opening door, not yet in Back Check areaBack Check & While in Hold Open On Steady Magnum is opening door in back checkClosing Slow Flash Magnum is allowing door to close, not yet in Latch Check area
Red Closed or Latch Check OffThe swing side door mounted ACUGARD is not activated and the header mounted Acusensor is not locking out an activation signal.
Fast Flashing The header mounted Acusensor is activated ( * see note 1 below)Slow Flashing The swing side door mounted ACUGARD is activatedOn Steady Close on Obstruction (Current Limit) activated (LED on for 5 seconds)
Opening Off The swing side door mounted ACUGARD is not activatedFast Flashing Not applicableSlow Flashing The swing side door mounted ACUGARD is activatedOn Steady Close on Obstruction (Current Limit) activated (LED on for 5 seconds)
Opening in Back Check Off The swing side door mounted ACUGARD is not activatedFast Flashing Not applicableSlow Flashing The swing side door mounted ACUGARD is activatedOn Steady Close on Obstruction (Current Limit) activated (LED on for 5 seconds)
Full Open Off The swing side door mounted ACUGARD is not activated and the header mounted Acusensor is not activated
Fast Flashing The header mounted Acusensor is activated ( * see note 1 below)Slow Flashing The swing side door mounted ACUGARD is activatedOn Steady Close on Obstruction (Current Limit) activated (LED on for 5 seconds)
Closing While in Back Check Off The swing side door mounted ACUGARD is not activatedFast Flashing Not applicableSlow Flashing The swing side door mounted ACUGARD is activatedOn Steady Close on Obstruction (Current Limit) activated (LED on for 5 seconds)
Closing Out of Back Check Off The swing side door mounted ACUGARD is not activatedFast Flashing Not applicableSlow Flashing The swing side door mounted ACUGARD is activated ( * see note 2 below)On Steady Close on Obstruction (Current Limit) activated (LED on for 5 seconds)
Note: If swing side door mounted ACUGARD is also active LED will flash slow instead.LED will only flash slow during closing if ACUGARD it is locking out an activation signal. If no activation signal is present, LED will not flash slow even if ACUGARD is activated.
1.2.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 7 www.NabcoEntrances.com 3/12/10
LED
TRANSFORMER
CAPACITOR
OFF
12
AUXPWR
4
J2
3
J5
AC IN
F2
SW2SW1
F1
RELAY RELAY
J4
TDAS
SIGNALINPUT
TDPG
LCHK
CLOSE
Fuse 1: 0.5A 24 VAC
STOP
OPEN
BCHK
CURRENTLIMIT
MOTOR
J1
R28
MAGNUM IVFuse 2: 5A 120/240
DN0033
BLACK
RED
Wiring Connectors:
There are four connectors located on the control board labeled J2, J3, J4, and J5 (Figure 2). There is a re-settable fuse 1 (F1) and a replaceable fuse 2 (F2).
J1 is the signal input. It is a six-pin connector with a mating connector installed.
1. Pin 1 - Safety with Lockout The wire to this pin is white. This is a lock out circuit so that the signal only works when the door is in the closed or fully open position. The logic is turned off and on through back check and door closed switches. Completing the circuit from the common (pin 6) will prevent the door from opening or closing from a fully closed or fully open position. It is generally used for swing side presence detectors where the detector needs to be deactivated as the door sweeps across the detection zone.
2. Pin 2 - Door Closed Switch The wire to this pin is orange. This circuit should be connected to the door closed switch to determine when the door is closed and out of the detection area of the presence sensor.
3. Pin 3 - Back check Switch The wire to this pin is blue. This circuit should be connected to the back check switch to determine when the door is in back check .
4. Pin 4 - Activation The wire to this pin is black. This circuit receives the activate signal from the actuating device when someone approaches.
5. Pin 5 - Continuous Safety The wire to this pin is purple. This circuit is used with the ACUGARD 3 System, swing side floor mats, or other continuous safety systems. Completing the circuit from the common (pin 6) will stop the door during opening, prevent activation during closing, as well as prevent it from moving if it is fully open or closed. This safety circuit is always active unlike the safety circuit described for pin 1.
6. Pin 6 - Common The wire to this pin is red. This is the common, so connecting this red wire to any of the other five will cause that feature to be activated. For example, connecting the red and blue will result in back check.
J2 is the 24 VAC output to the actuating device. It is a two-pin connector.
1. This circuitry was designed to work with any sensor that operates on 24 VAC. Do not exceed 0.5 amp current draw. A greater that 0.5 amp current will cause the onboard re-settable fuse (F1) to trip until the situation is corrected. If a sensor requires a different operating voltage, a separate power supply must be used to supply power to the sensor.
Figure 2 – Magnum IV Control
Adjustment potentiometers
Current Limit Pot. Set this pot fully clockwise initially
J1
J5
J2
J4
Diagnostic LED’s
Dip Switches 120 VAC fuse
24 VAC re-settable fuse
Slide switch UP for GT-500/710 Slide switch DOWN for GT-300/400
Braking module. Used to provide braking on closing cycle. Not used on GT-710.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 8 www.NabcoEntrances.com 3/12/10
J4 is the 120 VAC input connector. J5 is the motor feed. It is a four-pin connector that connects to the motor braking module (not used with GT-710) mounted at the end of the Magnum control board. This module uses a resistor & diode to slow the door down if J5 is accidentally unplugged while the door is in the open position.
1. Pin 1 is motor negative. The wire to this pin is red. 2. Pin 2 is motor positive. The wire to this pin is black. 3. Matching the color wires into the motor makes the unit work for right-hand
doors. Mismatching the wires makes the unit work for left-hand doors. 4. There are no wires to the Pin 3 and 4
NOTE: If the operator is the wrong hand, it CANNOT be corrected by reversing the
wiring leads into the motor. Fuse 1 (F1) is a 0.5 amp resettable fuse that protects auxiliary equipment that may be connected to J2. It also protects the auxiliary power circuit of the magnum board.
Fuse2 (F2) is a 5 amp fuse that protects the circuit board from voltage spikes and incorrect voltage being applied to the board.
Back Check – This takes place from about the last 10º of sweep to the full open position. Closing Speed – How fast the door moves from fully open to the final 10º before fully closed. Current Limit (or Door Block) – This sensitivity adjustments stops the activation if the door encounters an object in the path of the moving door while opening. Latch Check–This takes place from about the last 10º of sweep to the full closed position. Opening Speed – How fast the door opens from fully closed to approximately 80º open. Push-N-Go – Activation of the control by manually pushing the door.
Time Delay Activation Signal – When the door is activated via a push plate, a mat, a sensor, etc., this option determines how long the door will stay open. It is adjustable up to 60 seconds. Stop Adjustment – When an object is detected in the path of a moving door by a door mounted sensor while opening and the door is not in back check, this feature determines whether the door stops, slowly opens, or slowly closes.
FIGURE 3 - DOOR POSITIONS
Backcheck
Main speedFullOpen
Closed
LatchCheck
DN0035
Door Positions:
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 9 www.NabcoEntrances.com 3/12/10
OFF
12
43
SW2
R2 R3 R4 R5 R6 R7 R8
TDAS TDPG LCHK CLOSESTOP OPEN BCHK
CURRENTLIMIT
R28
DN0059
LED
Adjustments: There are three types of adjustments on the Magnum Control Board. These are; a slide switch, eight potentiometers and one selector (dip) switch. See Figure 2 for the location of these adjustments. Slide Switch - The slide switch can be used to select the appropriate mode of the Magnum IV control. The modes available are: UPPER POSITION - Upper position is for GT500 (Low Energy Operator) LOWER POSITION - Lower position is for GT300/400 (Standard Full Automatic Operator). By adjusting the slide switch , the Magnum board can control a Standard Swing full automatic operator or Low Energy operator. Leaving the slide switch in the upper position reduces power to the motor thereby allowing for the system to be adjusted to ANSI 156.19 Low Energy Standards. If it is desirable to increase opening power on a GT-500 or GT-710, move the slide switch to the lower position. For the latter, final installation must conform to ANSI 156.19. The amount of energy stored in the door and imparted to an object on impact is determined by both the weight and speed of the door. NABCO ENTRANCES INC. recommends setting opening and closing speeds as slow as owners will accept, AND below the maximums stated by ANSI.
The settings on the controller will vary slightly as the voltage supplied to the unit varies due to fluctuations in building and electrical supply loads. To allow for variations, the manufacturer recommends adding 1 second to ANSI’s minimum opening or closing times. Use a stopwatch for assistance. Potentiometers – There are eight potentiometers located on the control board. Use a small #0 Cross point or Phillips screw-driver to adjust each potentiometer. Don’t touch other parts of the board with the screwdriver. This could damage the electrical circuitry. Adjust potentiometers clockwise to increase the parameters (speeds, stops, delays, etc.), counterclockwise to decrease the parameters. Wait at least 5 seconds before testing the change. Recommended start settings correspond with positions on a clock with 12 o’clock at the top. The settings are a starting point. They are standard field approximations that might need to be adjusted for a specific situation. Selector (Dip) Switches – There is one bank of four switches located on the control board. The screwdriver can be used to toggle the switches on and off. Do not use a pencil. Note that the edge of the switch bank closest to the transformer is the “Off” position.
Customized Settings Magnum Board
Potentiometers: CAUTION! Changes should only be made by trained, qualified technicians.
Each control board has 8 potentiometers:
Stop Adjustment (STOPS) Opening Speed Adjustment (OPEN) Back Check Adjustment (BCHK) Time Delay Activating Signal (TDAS) Time Delay Push-N-Go (TDPG) Latch Check Adjustment (LCHK) Closing Speed Adjustment (CLOSE) Current Limit Adjustment (CURRENT LIMIT)
FIGURE 4 –SLIDE SWITCH
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 10 www.NabcoEntrances.com 3/12/10
Stop Adjustment (STOP):
When an object is sensed in the path of a moving door by a swing side safety mat or ACUGARD sensor connected to the control board through terminal # 3 (Violet wire) and the door is not in back check, this feature determines whether the door stops, slowly opens, or slowly closes. The recommended start setting is 12 o’clock.
Clockwise rotation of the potentiometer increases the stop power. If the stop power is
increased and an object is detected in the path of the opening door, the door will continue to open, but at a slower speed. If the stop power is decreased and an object is detected in the path of the opening door, the door will stop, reverse direction, and close slowly. Rotation of the potentiometer towards the midpoint of the setting reduces the speed at which the door moves.
NOTE: This adjustment is pertinent to signals from the Violet wire - continuous safety
input (Terminal Block #3) and is not related to current limit. Also, heavier doors will require more STOP power.
Opening Speed Adjustment (OPEN): This sets the door opening speed. The recommended starting position is 12 o’clock.
Clockwise rotation increases opening speed. GT-300/400 Application : 1.5 ~ 16 sec / 80 deg. GT-500/710 Application : 3.0 ~ 16 sec / 80 deg. Back Check Adjustment (BCHK) This sets back check speed. Back check takes place from about the last 10º of sweep to
the full-open position. The recommended starting position is 11 o’clock. Clockwise rotation increases back check speed. If back check is set too high the door will slam open. The current limit will trip. If back check is set too low the door will reach back check and stop.
GT-300/400 Application : 0.4 ~ 10 sec / 10 deg. GT-500/710 Application : 1.8 ~ 25 sec / 10 deg. Time Delay Activating Signal (TDAS): When the door is activated, this option determines how long the door will stay open after
the activation (or input signal) is released. This potentiometer is used when the door is in Timer Mode according to dipswitch # 4 (see next page). It is adjustable up to 60 seconds. The recommended starting position is 12 o’clock. Clockwise rotation increases time delay.
GT300/400/500/710 Application : 1 ~ 60 sec. Time Delay Push-N-Go (TDPG): When the Push-N-Go feature is used, this sets the time delay, which determines how long
the door stays open. It is adjustable up to 60 seconds. The recommended starting position is 12 o’clock. Clockwise rotation increases time delay. Set dipswitch # 4 to “ON” (see next page)
GT300/400/500/710 Application : 1 ~ 60 sec. Note: Push-N-Go time delay, when active, should be set for a shorter length of time
than the Time Delay Activating Signal. Note: There is a difference as to how Push-N-Go functions on the GT-500 versus the
GT300/400 & GT710. Because the GT-500 uses a clutch gear, Push-N-Go activation of GT-500 can only take place from a fully closed position and only once the door is manually pushed out of latch position. If Push-N-Go is desirable at any point in the door travel, order the GT-500 with a “clutchless” operator.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 11 www.NabcoEntrances.com 3/12/10
Latch Check Adjustment (LCHK): This sets latch check speed. Latch check takes place from about the last 10º of sweep to
the full-close position. The recommended starting position is 11 o’clock. Clockwise rotation increases latch check speed. If latch check is set too high the door will slam closed.
GT-300/400/500/710 Application : 1.5 ~ 5.0 sec / 10 deg. Closing Speed Adjustment (CLOSE): This sets the door closing speed. The recommended starting position is 12 o’clock.
Clockwise rotation increases closing speed. GT-300/400/500/710 Application : 3.0 ~ 12 sec / 80 deg. The hydraulic closer will regulate closing speed on the GT-710 . Current Limit Adjustment (Current Limit): Adjustment of this potentiometer from the fully clockwise position should be only be done
after all other adjustments are made and door operation is satisfactory.
In the case of GT-500 or GT-710, to satisfy ANSI Low Energy standard, it will be required to set this pot carefully. Although recommended setting is around 1:00 o’clock, it will be necessary to adjust setting depending upon door weight and speed. Current Limit stops activation and cuts power to the motor if the motor current exceeds
the setting. It is used to set how much force the opening door will push on an encountered object before it recycles. When the recycle is triggered, the door will stop and coast to a close. Reactivation will not be possible for 5 seconds. This adjustment is affected by opening speed. Set opening speed first. The recommended starting position for current limit might not be appropriate in windy conditions. For example, strong wind gusts against an exterior door may inadvertently cause it to recycle. Clockwise rotation makes the door less sensitive to objects in its path.
Dip Switches: Switch 1 – Not Used. Switch 2 – Not Used. Switch 3 1. On - Push-N-Go Inactive When the switch is ON, Push-N-Go is not active. 2. OFF - Push-N-Go Active When the switch is OFF, Push-N-Go is activated.
If Push-N-Go is active, switch # 4 below should be set to ON otherwise the door will go open when pushed and stay open, a second activation will be needed for the door to close.
Switch 4
1. On- Timer Mode When the switch is ON, the door will open, time out and close. 2. OFF - Sequential Mode When the switch is OFF, the door is in the sequential mode. One activation opens the door, a second activation is needed for the door to close.
FIGURE 5 - DIPSWITCHES
1234
OFF
Switches Shown in "ON" Position
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 12 www.NabcoEntrances.com 3/12/10
Symptom Action/Cause Solution
Operator does not function 1. Check Fuse 2 (F2). 2. Check for 120 VAC at connector J5 3. Check power to activation device at terminals 1 & 2. 4. Inline motor fuse on Protech motor blown.
1. Replace fuse 2. Check incoming power. If power is good, check connection to motor. Replace motor if necessary 3. If power exceeds 0.5 amps at 24 VAC, replace with lower draw sensor. 3. If voltage is too low, reduce accessory load. 4. Replace fuse.
Adjustment of Hydraulic Closer has no effect. (GT-710 only)
Check 4 pin motor connector on the board
For GT-710’s only: Pin #2 and #4 must be jumped by a wire
Door slams closed 1. GT-710: Main speed on hydraulic closer not adjusted properly 2. GT300/400/500: Closing speed not adjusted or motor circuit open 3. Inline motor fuse on Protech motor blown.
1. Turn main speed in direction of turtle 2. Adjust closing speed on Magnum control 2. check for open connection on motor circuit 3. Replace fuse.
Door slams open 1. All units: Back check speed not adjusted 2. GT-710: magnet not in proper location 3. GT-300/400/500: Operator not preloaded correctly
1. Adjust back check speed on hydraulic closer or Magnum control 2. Adjust back check potentiometer or relocate magnet 3. Pre-load operator by correctly installing arm on operator spindle as per hardware installation manual
Fuse 2 (F2) blows when door open is triggered
Check door activation device power consumption
If power draw exceeds 0.5 amps at 24 VAC, replace with lower draw sensor
Motor spins when activated but door does not open
1. GT-500: Check polarity of motor input wires at connector on motor 2. All units: motor/operator coupling or spyder coupling loose between motor and operator
1. Reverse motor leads on motor 2. Remove and separate motor and operator. Inspect couplings for looseness
Back check adjustment on Magnum board has no effect
1. GT-710: The fully open door position is greater than 90º and the back check adjustment on the hydraulic closer is overriding the controls of the Magnum board 2. All units: Door is not going into back check even though it is reaching 90 degrees
1. Adjust the back check screw on the bottom of the header out one turn 2. Reposition magnet on GT-710 or correctly pre-load arm on GT-300/400/500 as per hardware installation manual
No back check 1. GT-710: Magnets on main sprocket not in correct position. 2. GT-300/400/500: back check switch not closing at correct position
1. Follow instructions in GT-710 hardware installation manual to properly align magnets. 2. Follow instructions in GT-GT300/400/500 hardware installation manual to properly pre-load operator
Door does not stay tightly closed
1. All units: Preload on swing arm is not correct 2. GT-710: Spring adjustment not correct on LCN closer. 3. GT-710: Building stack pressure is excessive
1. Position arm as shown in hardware installation manual 2. Adjust spring tension on LCN closer as per GT-710 hardware installation manual. 3. Upgrade operator unit to GT 500
Troubleshooting:
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 13 www.NabcoEntrances.com 3/12/10
Presence Sensor does not function
1. All units: No power to sensor or defective sensor. 2. All units: Sensor not connected to White wire
1. Check harness wiring as per applicable section 2. Connect the output of the sensor to the Red # 5 and White # 4 connections on the terminal block.
Swing Side Presence Sensor is activated by opening or closing door
All units: Connection of sensor to wiring harness was to “Safety” not “Safety w/Lockout”
Rewire Safety Sensor to “Safety w/Lockout” connector. (pins Red # 5 and White # 4 connections on the terminal block.)
Swing Side ACUGARD 3, swing side floor mat, safety holding beams or other accessories do not function while door is moving
All units: Connection of accessories was made to “Safety w/Lockout” not “Continuous Safety”
Rewire accessory to “Continuous Safety” connection (Red # 5 and Violet # 3 connections on the terminal block.)
Sensor shows activation signal sent, but door does not open
All units: Sensor not connected properly to activation connector
Check harness wiring as per applicable section
One sensor does not activate both doors on a simultaneous pair
All units: Sensor is not connected to both control boards
Install simultaneous pair harness (P/N 229953)
Swing Side Door sensor does not function
1. All units: No power to sensor or defective sensor. 2. All units: Sensor not connected to Violet wire
1. Check harness wiring as per applicable section. 2. Connect the output of the sensor to the Red # 5 and Violet # 3 connections on the terminal block
Troubleshooting continued ….
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 14 www.NabcoEntrances.com 3/12/10
This section details the installation and adjustments of the Magnum IV control in a GT-300, GT-400 and GT-500 swing door unit.
Step 1: Install all components as per the applicable hardware installation manual.
Step 2: Connect all wiring and harnesses as per the following wiring information as it pertains to wiring and adjustments for GT-300, GT-400 and GT-500 Operators.
Back Check and Latch Micro Switches:
The operators used with the GT-300, GT-400 and GT-500’s provide the necessary latch check and back check limit switches the Magnum IV control requires for correct operation. These switches are mounted on the top of the operator assembly as illustrated in the diagram below. Note position of cams on right hand versus left hand operator.
Section A Wiring and Adjustment for GT-300,
GT-400 and GT-500 Operators
FIGURE 6 - LIMIT SWITCH CONFIGURATION
Black
Brown
Red
Blue
Green
W hit e
Latch-checkLimit switch
BreakoutLimit switch
Back-checkLimit switch
Lef t Hand Operator shownIn DOOR CLOSED posit ion
Right Hand Operator shownIn DOOR CLOSED posit ion
Black
Brown
W hit e
Red
GreenBlue
Back-checkLimit switch
BreakoutLimit switch
Latch-checkLimit switch
DN0051
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 15 www.NabcoEntrances.com 3/12/10
Required Wiring Harnesses:
The following harnesses are necessary to complete the installation (see below):
a. Power Harness, Magnum Board Part # 21-9933 (for single door) 14-5883 for Simultaneous Pair door)
b. Main Harness Assy, Magnum Board Part # 22-10065 (for single door) 22-10270 (for Simultaneous Pair door)
c. Magnum Board Harness for 300/400/500 Part # 21-9934
FIGURE 7 - WIRING HARNESSES FOR MAGNUM IV
300/400/500 Harness, MagnumP/N 21-9934
1
Power Harness - Sim.PairP/N 14-5883
Micro Switch - Short ArmP/N 14-3867
DN0046
Main Harness - Sim. PairP/N 22-10270
Main Harness - SingleP/N 22-10065
Magnum IV & Chassis AssemblyP/N 12-10292
Power Harness - SingleP/N 21-9933
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 16 www.NabcoEntrances.com 3/12/10
Wiring for Rocker switch:
Rocker Switch (part # 10-3528) is available. Connect the red wire to activation input, the white wire to 24VAC common and the black wire to activation signal of sensing device.
Wiring for Break – out: When the unit has a Break-out feature, the panic breakout circuit must be connected to shut down the system when the door is broken out in the opposite direct. Please refer to the following procedure. a. A Panic Latch kit must be installed When installing the panic latch, flip the direction of the panic latch so that the “ ← EXT” arrow points to Interior side of the building. This makes the switch close instead of opening when the door is broken out. The contacts of the switch would be changed to Normally Open from Normally Closed. See Figure 8 below.
b. Cut the connectors from the Brown and Black wires on the Magnum micro switch harness as shown below. Connect the Brown and Black wires to" Continuous Safety” input of Terminal Block between Terminal Block #3 violet and #5 red) as shown in Figure # 9.
c. Also cut the connectors off the Panic Latch harness and connect these wires to “Continuous Safety” input of Terminal Block. (Between Terminal Block #3 violet and #5 red). Refer to the Figure # 10 below for complete wiring information.
FIGURE 8 PANIC LATCH
FIGURE 9 MICRO SWITCH HARNESS
FIGURE 10 BREAKOUT CIRCUIT WIRING
DIAGRAM
EXTInteriorSide
ExteriorSide
DN0060
Black
Black Brown
Brown
DN0061
USE THESE CONNECTIONS ON INSWING DOORS WITH PANIC BREAKOUT
DN0049
Panic Latch must be flipped.Arrow marked "EXT" must point into the building.(Contacts must close when door is broken out)
Back Check Limit Switch
Harness Assy
(Black and Brown)Breakout Limit Switch: N.O.
Terminal Block # 3 & # 5MUST be connected to Continuous Safety input,Breakout Limit Switch Signal and Panic Latch SignalWhen the unit has Panic Breakout feature,
Panic Latch KitPart # 11- 0941
RedRed
Brown
Black
Red: Comm, Blue: N.C.
for Magnum Board300/400/500 HarnessPart # 21-9934
234
F F O
Selector Switches
ONOFF
1
BRO
WN
BLA
CK
RED
WH
ITE
VIO
LET
OR
ANG
E
MotorJ5
PwrAux
J4
R40R29R27R24R21R13R8
CLOSELCHKTDPGTDASBCHKOPENSTOPJ2
J3
RelayLIMIT
CURRENT
R23
Relay
Transformer
Magnum IV control
Operator Assembly
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 17 www.NabcoEntrances.com 3/12/10
Figu
re 1
1 - G
ener
al W
iring
- Si
ngle
Dia
gram
DN
0047
23
45
6
Ter
#5
Not
e:C
omm
on c
onne
ctio
n #
5 (R
ed) n
ot s
how
n fo
r sim
plic
ity
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)
Pan
ic L
atch
mus
t be
flipp
ed.
arro
w m
arke
d "E
XT"
poi
nts
into
the
build
ing.
(C
onta
cts
mus
t clo
se w
hen
door
is b
roke
n ou
t)
to T
erm
inal
#5
(red
)
12
34
56
ON
/OFF
R
OC
KER
S
WIT
CH
120
VAC
Com
mon
N.O
.
Dev
ice
Not
Use
d
Typi
cal
Mat
or
Wal
l Sw
itch
24 V
AC
Inpu
t
Typi
cal S
enso
r
Dev
ice
If R
ocke
r Sw
itch
is n
ot R
equi
red
Con
nect
the
Act
ivat
ion
Sig
nals
toTe
rmin
al B
lock
#6
Dire
ctly
Par
t # 1
0-35
28R
S-1
2 R
ocke
r Sw
itch
Red
Red
Par
t # 1
1- 0
941
Pan
ic L
atch
Kit
Whe
n th
e un
it ha
s Pa
nic
Bre
akou
t fea
ture
,B
reak
out L
imit
Sw
itch
Sig
nal a
nd/o
r Pan
ic L
atch
Sig
nal
MU
ST
be c
onne
cted
to C
ontin
uous
Saf
ety
inpu
t,Te
rmin
al B
lock
#3

Bre
akou
t Lim
it S
witc
h: N
.O.
(Bla
ck a
nd B
row
n)
Latc
h C
heck
Lim
it S
witc
h
Par
t # 2
2-10
065
Har
ness
Ass
yfo
r Sin
gle
Bac
k C
heck
Lim
it Sw
itch
Off Hol
d O
pen
On
Off
Whi
te
Blac
k
Red
Act
ivat
ion
Safe
ty w
ith L
ocko
utdu
ring
door
sw
ing
Con
tinuo
us S
afet
y
24 V
AC
AU
X O
utpu
tfo
r sen
sors
TER
MIN
AL
BLO
CK
#1
BR
OW
N
#2
OR
AN
GE
#3
VIO
LET
#4
WH
ITE
#5
RE
D
#6
BLA
CK
24V
AC N
EU
TRAL
24V
AC H
OT
CO
NTI
NU
OU
S S
AFE
TY
SAF
ETY
WIT
H L
OC
KO
UT
24V
AC
CO
MM
ON
AC
TIVA
TIO
N
Gro
und
Bla
ck(H
ot)
Blac
k
Blac
k
Whi
te (N
eutra
l)
Par
t # 2
1-99
3430
0/40
0/50
0 H
arne
ssfo
r Mag
num
Boa
rd
Red
: Com
m, B
lue:
N.C
.
Whi
te: C
omm
, Gre
en: N
.C.
Bla
ckBr
own
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 18 www.NabcoEntrances.com 3/12/10
Figu
re 1
2 - G
ener
al W
iring
– S
imul
tane
ous
Pair
Red
Red
Inst
alle
r to
prov
ide
utilit
y po
wer
115V
AC
6A
Par
t # 2
1-99
3430
0/40
0/50
0 H
arne
ssfo
r Mag
num
Boa
rd
Whi
te: C
omm
, Gre
en: N
.C.
Latc
h C
heck
Lim
it Sw
itch
Blac
k
Gre
en
Whe
n th
e un
it ha
s P
anic
Bre
akou
t fea
ture
,B
reak
out L
imit
Sw
itch
Sig
nals
and
Pan
ic L
atch
Sig
nals
MU
ST
be c
onne
cted
to C
ontin
uous
Saf
ety
inpu
t,Te
rmin
al B
lock
#3
& #
5
Bre
akou
t Lim
it S
witc
h: N
.O.
(Bla
ck a
nd B
row
n)
Bac
k C
heck
Lim
it S
witc
h
Gre
en
ON
/OFF
R
OC
KER
S
WIT
CH
Red
Ter
#5
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
Pani
c La
tch
mus
t be
flipp
ed.
arro
w m
arke
d "E
XT"
poi
nts
into
th
e bu
ildin
g. (
Con
tact
s m
ust
clos
e w
hen
door
is b
roke
n ou
t)
Not
e:C
omm
on c
onne
ctio
n #5
(Red
) no
t sho
wn
for s
impl
icity
DN
0048
Pan
ic L
atch
mus
t be
flipp
ed.
arro
w m
arke
d "E
XT"
poi
nts
into
th
e bu
ildin
g.
(Con
tact
s m
ust c
lose
whe
n do
or
is b
roke
n ou
t)
2
Whi
te
Activ
atio
n
Saf
ety
with
Loc
kout
durin
g do
or s
win
gC
ontin
uous
Saf
ety
24 V
AC
AU
X O
utpu
tfo
r sen
sors
13
45
6
Not
Use
d24
VAC
Inpu
tC
omm
on
Typi
cal
Mat
or
Wal
l Sw
itch
Dev
ice
Typi
cal S
enso
r
Dev
ice
N.O
.
TER
MIN
AL
BLO
CK
#1
BR
OW
N
#2
OR
AN
GE
#3
VIO
LET
#4
WH
ITE
#5
RE
D
#6
BLA
CK
24V
AC
NE
UTR
AL
24V
AC
HO
T
CO
NTI
NU
OU
S S
AFE
TY
SA
FETY
WIT
H L
OC
KO
UT
24V
AC
CO
MM
ON
AC
TIV
ATI
ON
Par
t # 2
2-10
270
Har
ness
Ass
yfo
r Sim
Pai
r
Bla
ck
Par
t # 1
1- 0
941
Pan
ic L
atch
Kit
Off Hol
d O
pen
On
Off
Par
t # 1
0-35
28R
S-12
Roc
ker S
witc
h
Bla
ck
Red
Bro
wn
Bla
ck
Bla
ckB
lack
Whi
te
Bla
ck
Gre
enG
roun
ded
Bla
ck
Whi
te (N
eutra
l)Bl
ack
(Hot
)
Red
: Com
m, B
lue:
N.C
.
Bro
wn
Par
t # 2
1-99
3430
0/40
0/50
0 H
arne
ssfo
r Mag
num
Boa
rd
IF R
OC
KER
SW
ITC
H IS
NO
T R
EQU
IRED
,C
ON
NE
CT
THE
ACTI
VAT
ION
SIG
NAL
S TO
TE
RM
INA
L B
LOC
K #6
DIR
EC
TLY.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 19 www.NabcoEntrances.com 3/12/10
Table 1 – Comparison of Magnum IV to the Analog Controller
Magnum IV Board Analog Controller Adjustable opening speed via potentiometer Three position adjustment on opening speed. Adjustable closing speed via potentiometer Adjustment by changing resistors Adjustable Back-check speed via potentiometer Three position speed adjustment Adjustable Latch-check speed via potentiometer Three position speed adjustment Adjustable current limit/door block trip. No adjustment. Adjustable activation timer (0 to 60 seconds) Requires separate time delay module Adjustable separate Push-N-Go timer (0 to 60 seconds) No adjustment.
Adjustable door action when detection (continuous safety) occurs – allow door to stop, creep open or creep closed.
No adjustment.
Automatic shut-off of motor if door does not open within 15 seconds. N/A
Separate connections provided for swing side mats and swing side presence detector (Continuous safety and safety with lockout).
Only one connection provided
Enable/disable sequential operation via dip switch. N/A Enable/disable Push-N-Go via dip switch. Requires separate module Visual onboard LED status indicators Not Available
This section offers instructions on how to upgrade an existing GT300/400/500 installation with the Magnum IV and related hardware. Tools required: Phillips Screwdriver, #0 (for potentiometers), #2 Slotted Screwdrivers, Small and Medium 9/16” socket and ratchet
Section B Retrofit Kit Manual
Model 300/400/500 Swing Door System With Magnum IV Control
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 20 www.NabcoEntrances.com 3/12/10
Hard Ware Kit List:
This kit has been shipped with the following installation hardware.
-01 11-10293-01 Magnum Board Retrofit Kit for Single Swinger
-02 11-10293-02 Magnum Board Retrofit Kit for Simultaneous Pair Swinger
Part # Part Description Qty Notes
-01 Single
-02 Sim- Pair
1 12-10292 Magnum IV Board & Chassis Assembly 1 2 With Braking Module 2 22-10065 Main Harness - Single 1 --- With Terminal Block
3 22-10270 Main Harness – Simultaneous Pair --- 1 With Terminal Block
4 21-9934 300/400/500 Harness, Magnum Board 1 2
5 21-9933 Power Harness - Single 1 --- 6 14-5883 Power Harness – Simultaneous Pair --- 1 7 14-3867 Micro switch – Short Arm 1 2 8 15-10682 Magnum IV Control
Wiring & Adjustment Manual for Gyro Tech Swing Door Operators
1 1
9 24-3258-01 Screw, Micro switch 2 4
10 24-0017-19 Washer, Micro switch 2 4
FIGURE 13 MAGNUM CONTROL AND HARNESSES
300/400/500 Harness, MagnumP/N 21-9934
1
Power Harness - Sim.PairP/N 14-5883
Micro Switch - Short ArmP/N 14-3867
DN0046
Main Harness - Sim. PairP/N 22-10270
Main Harness - SingleP/N 22-10065
Magnum IV & Chassis AssemblyP/N 12-10292
Power Harness - SingleP/N 21-9933
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 21 www.NabcoEntrances.com 3/12/10
Conversion of a GT300/400/500 to a Magnum IV :
1. Shut off power to the header. 2. Uninstall the swing operator from the header. 3. Remove all wires and the switch harness from the operator. 4. Remove the control board and the appropriate wiring from the header. Mounting clip would be used for Magnum IV assembly. 5. Install the Magnum IV board next to the operator using the mounting clip from the analog control box. 6. After removing the existing switch harness from the operator, install the GT 300/400/500 Magnum Harness P/N 21-9934 to the back-check, latch-check and break-out limit micro switches on the operator as shown below. The operator used with the GT-300, GT-400 and GT-500’s provide the necessary latch check and back check limit switches the Magnum IV control requires for correct operation. These switches are mounted on the top of the operator assembly as illustrated in Figure 14 below. Note: position of cams on right hand versus left hand operator.
FIGURE 14 - BACK CHECK AND LATCH MICRO SWITCHES
When the unit has a break-out feature, the panic breakout circuit must be connected to shut down the system when the door is broken out in the opposite direct. Please refer to the following procedure.
a. A Panic Latch kit must be installed
When installing the panic latch, flip the direction of the panic latch so that the “ ← EXT” arrow points to Interior side of the building. This makes the switch close instead of opening when the door is broken out. The contacts of the switch would be changed to normally open from normally closed. See Figure 15 below.
FIGURE 15 - BOTTOM VIEW OF PANIC LATCH
When a unit has a panic breakout feature a panic breakout latch must be used. This latch is flipped so that the contacts will close when the door is broken out.
Black
Brown
Red
Blue
Green
W hit e
Latch-checkLimit switch
BreakoutLimit switch
Back-checkLimit switch
Lef t Hand Operator shownIn DOOR CLOSED posit ion
Right Hand Operator shownIn DOOR CLOSED posit ion
Black
Brown
W hit e
Red
GreenBlue
Back-checkLimit switch
BreakoutLimit switch
Latch-checkLimit switch
DN0051
EXTInteriorSide
ExteriorSide
DN0060
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 22 www.NabcoEntrances.com 3/12/10
b. Cut the connectors from the Brown and Black wires on the GT 300/400/500 Magnum Micro Switch Harness P/N 21-9934 as shown below. Connect the Brown and Black wires to Continuous Safety” input of Terminal Block. (Between Terminal Block #3 violet and #5 red) as shown below.
c. Also cut the connectors off the Panic Latch harness and connect these wires to “Continuous Safety” input of Terminal Block.(Between Terminal Block #3 violet and #5 red). Refer to the diagram below for complete wiring information.
FIGURE 17 - PANIC LATCH AND PANIC BREAKOUT LIMIT SWITCH WIRING INSTRUCTIONS
FIGURE 16 - MICRO SWITCH HARNESS
Black
Black Brown
Brown
DN0061
USE THESE CONNECTIONS ON INSWING DOORS WITH PANIC BREAKOUT
DN0049
Panic Latch must be flipped.Arrow marked "EXT" must point into the building.(Contacts must close when door is broken out)
Back Check Limit Switch
Harness Assy
(Black and Brown)Breakout Limit Switch: N.O.
Terminal Block # 3 & # 5MUST be connected to Continuous Safety input,Breakout Limit Switch Signal and Panic Latch SignalWhen the unit has Panic Breakout feature,
Panic Latch KitPart # 11- 0941
RedRed
Brown
Black
Red: Comm, Blue: N.C.
for Magnum Board300/400/500 HarnessPart # 21-9934
234
F F O
Selector Switches
ONOFF
1B
RO
WN
BLA
CK
RE
D
WH
ITE
VIO
LET
OR
AN
GE
MotorJ5
PwrAux
J4
R40R29R27R24R21R13R8
CLOSELCHKTDPGTDASBCHKOPENSTOPJ2
J3
RelayLIMIT
CURRENT
R23
Relay
Transformer
Magnum IV control
Operator Assembly
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 23 www.NabcoEntrances.com 3/12/10
7. Plug the power harness into the Magnum IV board. Connect the green wire (ground) to the header chassis,
black 120 VAC wire to black through thermal protector, and white wire to white wire as shown on the
next page.
8. Connect the four-pin plug from the limit switches to the plug at the end of the main harness. Figure 18)
9. Connect the Rocker Switch to the terminal block of the main harness. (Figure 18)
10. Connect the motor harness from J5 (marked MOTOR) on the Magnum IV board to the associated red and
black terminals on the motor. (Figure 18)
11. Connect the six-pin connector from the main harness to J1 on the Magnum IV board.
12. Connect the two-pin connector from the main harness to J2 (marked AUX PWR) on the Magnum IV
board.
13. Connect the activation/detection devices to the terminal block of the main harness. (Figure 18).
14. Cap off all unused wires.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 24 www.NabcoEntrances.com 3/12/10
Figu
re 1
8 - G
ener
al W
iring
- Si
ngle
Dia
gram
DN
0047
23
45
6
Ter
#5
Not
e:C
omm
on c
onne
ctio
n #
5 (R
ed) n
ot s
how
n fo
r sim
plic
ity
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)
Pan
ic L
atch
mus
t be
flipp
ed.
arro
w m
arke
d "E
XT"
poi
nts
into
the
build
ing.
(C
onta
cts
mus
t clo
se w
hen
door
is b
roke
n ou
t)
to T
erm
inal
#5
(red
)
12
34
56
ON
/OFF
R
OC
KER
S
WIT
CH
120
VAC
Com
mon
N.O
.
Dev
ice
Not
Use
d
Typi
cal
Mat
or
Wal
l Sw
itch
24 V
AC
Inpu
t
Typi
cal S
enso
r
Dev
ice
If R
ocke
r Sw
itch
is n
ot R
equi
red
Con
nect
the
Act
ivat
ion
Sig
nals
toTe
rmin
al B
lock
#6
Dire
ctly
Par
t # 1
0-35
28R
S-1
2 R
ocke
r Sw
itch
Red
Red
Par
t # 1
1- 0
941
Pan
ic L
atch
Kit
Whe
n th
e un
it ha
s Pa
nic
Bre
akou
t fea
ture
,B
reak
out L
imit
Sw
itch
Sig
nal a
nd/o
r Pan
ic L
atch
Sig
nal
MU
ST
be c
onne
cted
to C
ontin
uous
Saf
ety
inpu
t,Te
rmin
al B
lock
#3

Bre
akou
t Lim
it S
witc
h: N
.O.
(Bla
ck a
nd B
row
n)
Latc
h C
heck
Lim
it S
witc
h
Par
t # 2
2-10
065
Har
ness
Ass
yfo
r Sin
gle
Bac
k C
heck
Lim
it Sw
itch
Off Hol
d O
pen
On
Off
Whi
te
Blac
k
Red
Act
ivat
ion
Safe
ty w
ith L
ocko
utdu
ring
door
sw
ing
Con
tinuo
us S
afet
y
24 V
AC
AU
X O
utpu
tfo
r sen
sors
TER
MIN
AL
BLO
CK
#1
BR
OW
N
#2
OR
AN
GE
#3
VIO
LET
#4
WH
ITE
#5
RE
D
#6
BLA
CK
24V
AC N
EU
TRAL
24V
AC H
OT
CO
NTI
NU
OU
S S
AFE
TY
SAF
ETY
WIT
H L
OC
KOU
T
24V
AC
CO
MM
ON
AC
TIVA
TIO
N
Gro
und
Bla
ck(H
ot)
Blac
k
Blac
k
Whi
te (N
eutra
l)
Par
t # 2
1-99
3430
0/40
0/50
0 H
arne
ssfo
r Mag
num
Boa
rd
Red
: Com
m, B
lue:
N.C
.
Whi
te: C
omm
, Gre
en: N
.C.
Bla
ckBr
own
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 25 www.NabcoEntrances.com 3/12/10
Figu
re 1
9 - G
ener
al W
iring
– S
imul
tane
ous
Pair
Red
Red
Inst
alle
r to
prov
ide
utilit
y po
wer
115V
AC
6A
Par
t # 2
1-99
3430
0/40
0/50
0 H
arne
ssfo
r Mag
num
Boa
rd
Whi
te: C
omm
, Gre
en: N
.C.
Latc
h C
heck
Lim
it Sw
itch
Blac
k
Gre
en
Whe
n th
e un
it ha
s P
anic
Bre
akou
t fea
ture
,B
reak
out L
imit
Sw
itch
Sig
nals
and
Pan
ic L
atch
Sig
nals
MU
ST
be c
onne
cted
to C
ontin
uous
Saf
ety
inpu
t,Te
rmin
al B
lock
#3
& #
5
Bre
akou
t Lim
it S
witc
h: N
.O.
(Bla
ck a
nd B
row
n)
Bac
k C
heck
Lim
it S
witc
h
Gre
en
ON
/OFF
R
OC
KER
S
WIT
CH
Red
Ter
#5
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
to T
erm
inal
#5
(red
)to
Ter
min
al
#5 (r
ed)
Pani
c La
tch
mus
t be
flipp
ed.
arro
w m
arke
d "E
XT"
poi
nts
into
th
e bu
ildin
g. (
Con
tact
s m
ust
clos
e w
hen
door
is b
roke
n ou
t)
Not
e:C
omm
on c
onne
ctio
n #5
(Red
) no
t sho
wn
for s
impl
icity
DN
0048
Pan
ic L
atch
mus
t be
flipp
ed.
arro
w m
arke
d "E
XT"
poi
nts
into
th
e bu
ildin
g.
(Con
tact
s m
ust c
lose
whe
n do
or
is b
roke
n ou
t)
2
Whi
te
Activ
atio
n
Saf
ety
with
Loc
kout
durin
g do
or s
win
gC
ontin
uous
Saf
ety
24 V
AC
AU
X O
utpu
tfo
r sen
sors
13
45
6
Not
Use
d24
VAC
Inpu
tC
omm
on
Typi
cal
Mat
or
Wal
l Sw
itch
Dev
ice
Typi
cal S
enso
r
Dev
ice
N.O
.
TER
MIN
AL
BLO
CK
#1
BR
OW
N
#2
OR
AN
GE
#3
VIO
LET
#4
WH
ITE
#5
RE
D
#6
BLA
CK
24V
AC
NE
UTR
AL
24V
AC
HO
T
CO
NTI
NU
OU
S S
AFE
TY
SA
FETY
WIT
H L
OC
KO
UT
24V
AC
CO
MM
ON
AC
TIV
ATI
ON
Par
t # 2
2-10
270
Har
ness
Ass
yfo
r Sim
Pai
r
Bla
ck
Par
t # 1
1- 0
941
Pan
ic L
atch
Kit
Off Hol
d O
pen
On
Off
Par
t # 1
0-35
28R
S-12
Roc
ker S
witc
h
Bla
ck
Red
Bro
wn
Bla
ck
Bla
ckB
lack
Whi
te
Bla
ck
Gre
enG
roun
ded
Bla
ck
Whi
te (N
eutra
l)Bl
ack
(Hot
)
Red
: Com
m, B
lue:
N.C
.
Bro
wn
Par
t # 2
1-99
3430
0/40
0/50
0 H
arne
ssfo
r Mag
num
Boa
rd
IF R
OC
KER
SW
ITC
H IS
NO
T R
EQU
IRED
,C
ON
NE
CT
THE
ACTI
VAT
ION
SIG
NAL
S TO
TE
RM
INA
L B
LOC
K #6
DIR
EC
TLY.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 26 www.NabcoEntrances.com 3/12/10
Section C Wiring and Adjustment for GT-710 Operators
This section details the installation and adjustments of the Magnum IV control in a GT-710 swing door unit.
Step 1: Install all components as per the applicable hardware installation manual.
Step 2: Connect all wiring and harnesses as per the following wiring information as they pertains to wiring and adjustments for GT-710 Operator.
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 27 www.NabcoEntrances.com 3/12/10
Figu
re 2
0 S
ing
le D
oo
r
GEN
ERA
L W
IRIN
G D
IAG
RA
M
AC
TIVA
TIO
N
24 V
AC
CO
MM
ON
SA
FETY
WIT
H L
OC
KO
UT
CO
NTI
NU
OU
S S
AFE
TY
24 V
AC
HO
T
24 V
AC
NE
UTR
AL
TER
MIN
AL
BLO
CK
Mai
n H
arne
ss (p
/n 2
2100
65)
Inpu
t24
VA
C
Con
tinuo
us S
afet
y
Pow
er H
arne
ss(p
/n 2
1993
3) Gro
und
Inst
alle
r to
prov
ide
utilit
ypo
wer
Hot
Neu
tral
GR
EEN
BLACK
BLA
CK
BLA
CK
3Tr
ansf
orm
erD
oor
Bloc
k
Rel
ay
On
Off
WHITE
Fuse
2: 3
A
Rel
ay
4
J5J1
Sel
ecto
r Sw
itche
s
R13
R8
R21
Fuse
1: .
5AJ4J2
STO
PO
PEN
BCH
K
R29
R40
R27
R24
LCH
K
R23
1 2
TDPG
TDA
SC
LOSE
CO
NN
EC
T TH
E A
CTI
VAT
ION
SIG
NA
LS T
O R
ED
WH
ITE
65
42
31
VIO
LET
#3 #6#5#4
BLA
CK
RED
WH
ITE
#1 #2
BRO
WN
OR
AN
GE
durin
g do
or s
win
g
Inpu
t24
VAC
Saf
ety
with
Loc
kout
Mag
netic
Ree
dS
witc
h (p
/n 1
0306
9)
On
BLA
CK
Act
ivat
ion
24 V
ACIn
put
for s
enso
rs24
VA
C A
UX
Out
put
TER
MIN
AL
BLO
CK
DIR
EC
TLY.
IF R
OC
KER
SW
ITC
H IS
NO
T R
EQ
UIR
ED
,
Off
Off Hol
d O
pen
Switc
h (p
/n 1
0352
8)
4 3
2 11
24
3
Com
mon
Inpu
tN
.O.
Typi
cal S
enso
rD
evic
e 24 V
AC
Typi
cal
Mat
or
Wal
l Sw
itch
Not
Use
d
Dev
ice
DN
0052
ON
/OFF
R
OC
KER
S
WIT
CH
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 28 www.NabcoEntrances.com 3/12/10
NE
UTR
AL
HO
T
BLA
CK
BLA
CK
AC
TIVA
TIO
N24
VAC
CO
MM
ON
SA
FETY
WIT
H L
OC
KOU
TC
ON
TIN
UO
US
SAFE
TY24
VAC
HO
T24
VAC
NEU
TRAL
#6
BLA
CK
#5
RED
#4
WH
ITE
#3
V
IOLE
T
#2
OR
AN
GE
#1
BR
OW
N
TER
MIN
AL
BLO
CK
24
53
61
DN
0053
ON
/OFF
R
OC
KE
R
SWIT
CH
J4Tr
ansf
orm
er
R23
16
35
42
Fuse
1: .
5A
R8
R13
STO
PJ2
OP
EN
R24
R21
R27
Sel
ecto
r Sw
itche
s
TDA
SB
CH
KTD
PG
1 2
R40
R29
CLO
SELC
HK
Doo
rB
lock
WHITE
Fuse
2: 3
A
Rel
ay
On
Off
43
BLACK
Rel
ay
J1 J5
Wiri
ng D
iagr
amfo
rW
all S
witc
h A
ctiv
atio
n
GR
EEN
GR
OU
ND
Figu
re 2
1
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 29 www.NabcoEntrances.com 3/12/10
Tran
sfor
mer
Doo
rB
lock
Rel
ay
On
Off
Fuse
2: 3
A
Rel
ay
4
J5J1
Sel
ecto
r Sw
itche
s
R13
R8
R21
Fuse
1: .
5AJ4J2
STO
PO
PEN
BC
HK
R29
R40
R27
R24
LCH
K
R23
1 2
TDPG
TDAS
CLO
SE
RED
OffOff
Hold Open
On
BLACK
Act
ivat
ion
WHITE
6 5 4
Rel
ay
On
Off
3 42
Sel
ecto
r Sw
itche
s
BC
HK
TDAS
Doo
rBl
ock
Rel
ay
J5J1
CLO
SE
R23LC
HK
Max
imum
cu
rren
t dra
w fo
rac
cess
orie
s is
0.
5 am
ps.
BlackRedWhiteVioletOrangeBrown
Black
WhiteViolet
Brown
Gre
en
Rig
ht H
and
Ope
rato
r Dep
endi
ng o
n th
e ov
eral
lw
idth
, the
con
trol b
oard
sm
ay b
e st
acke
d on
top
ofon
e an
othe
r.
Har
ness
Ass
'y fo
r Si
mul
tane
ous
Pair
(P/N
221
0270
)
Left
Han
d O
pera
tor
From
righ
tha
nd
oper
ator
cont
rols
.
Gre
en
(The
rmal
Cut
out S
witc
h)
BLA
CK
Bla
ck (H
ot)
Whi
te (N
eutra
l)G
roun
d
Whi
te (N
eutra
l)
Bla
ck (H
ot)
Inst
alle
r to
prov
ide
utili
ty
pow
er.
Mai
n H
arne
ss
(P/N
221
0065
)
IF R
OC
KE
R S
WIT
CH
IS N
OT
REQ
UIR
EDC
ON
NE
CT
THE
AC
TIVA
TIO
N
SIG
NAL
DIR
ECTL
Y TO
TE
RM
INA
L #
6 A
S SH
OW
N B
Y D
OTT
ED
LIN
E
Switc
h (P
/N 1
0352
8)
24 V
AC
AU
X O
utpu
tfo
r sen
sors
DN
0054
23 1
VIO
LET
#3 #6#5#4
BLA
CK
RED
WH
ITE
#1 #2
BR
OW
N
OR
AN
GE
durin
g do
or s
win
gS
afet
y w
ith L
ocko
ut
Mag
netic
Ree
dSw
itch
(p/n
103
069)
J4J2ST
OP
1 4 3
2 1
24
3
R40
R27
R21
R24
R29
TDPG
1
WIR
ING
DIA
GR
AM
FOR
SIM
ULT
AN
EOU
S PA
IRS
AC
TIVA
TIO
N
24 V
AC
CO
MM
ON
SAFE
TY W
ITH
LO
CKO
UT
CO
NTI
NU
OU
S S
AFE
TY
24 V
AC H
OT
24 V
AC
NE
UTR
AL
TER
MIN
AL B
LOC
K
Con
tinuo
us S
afet
y
To o
ther
end
ofth
e he
ader
.Bl
ack
(Hot
) W
hite
(Neu
tral)
(The
rmal
Cut
out S
witc
h)BL
ACK
3
4 3
2 11
24
3
OPE
N
Tran
sfor
mer
Fuse
1: .
5A
Fuse
2: 3
A
R13
R8
ON
/OFF
R
OC
KER
S
WIT
CH
Figu
re 2
2
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 30 www.NabcoEntrances.com 3/12/10
Blac
k
Tran
sfor
mer
Gre
en G
roun
dSc
rew
&
Cup
Was
her
Whi
teBl
ack
Blue
Gre
enG
reen
Brow
n
Blac
kBl
ack
Whi
te
Blac
k w
ith w
hite
stri
peR
ed
Gre
enG
reen
Brow
nTa
n
Gre
en
Tran
sfor
mer
J4
Mot
or Blac
k
J2
STO
P
R8
1
OFF
Rel
ayO
N
2 43
BCH
K
R21
DN
0055
Tran
sfor
mer
In
stal
latio
n an
d W
iring
for 2
40
Volts
R13 Se
lect
or S
witc
hes
OPE
N
Gre
en w
ires
are
24 v
olt A
Can
d ca
n be
use
d to
pow
erac
cess
ary
devi
ces,
mot
ion
dete
ctor
s, e
tc.
Gre
en (G
roun
d)Se
rvic
e Gre
en G
roun
dSc
rew
&
Cup
Was
her
220-
240
Vol
t50
- 60
Hz
#148
743
Spac
er
#240
010-
01
Brow
n (H
ot)
Blue
(Neu
tral)
Scre
w
#218
754
Tran
sfor
mer
Figu
re 2
3
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 31 www.NabcoEntrances.com 3/12/10
Figu
re 2
4
RED
BLA
CK
WH
ITE
GR
EE
N
24 V
AC
/DC
65
43
21
ORANGEVIOLETWHITE
REDBLACK
BROWN
Off Hol
d O
pen
On
Off
WH
ITE
BLA
CK
RED
TER
MIN
AL
BLO
CK
#1
BR
OW
N
#2
OR
ANG
E
#3
VIO
LET
#4
WH
ITE
#5
RED
#6
BLA
CK
24V
AC N
EUTR
AL
24V
AC H
OT
CO
NTI
NU
OU
S SA
FETY
SAF
ETY
WIT
H L
OC
KOU
T
24V
AC C
OM
MO
N
AC
TIVA
TIO
N
P/N
10-
3528
RO
CK
ER
SW
ITC
H
Wiri
ng D
iagr
am fo
r Rad
io
Act
ivat
ion
Usi
ng L
inea
r Rec
ieve
r
DN
0056
Four
Wire
R
adio
R
ecei
ver
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 32 www.NabcoEntrances.com 3/12/10
Figu
re 2
5
AC
TIVA
TIO
N
24V
AC
CO
MM
ON
SAF
ETY
WIT
H L
OC
KOU
T
CO
NTI
NU
OU
S SA
FETY
24V
AC H
OT
24V
AC
NEU
TRAL
#6
BLA
CK
#5
RE
D
#4
WH
ITE
#3
VIO
LET
#2
OR
AN
GE
#1
BR
OW
N
MA
GN
UM
TE
RM
INA
L B
LOC
K
DN
0056
Act
ivat
ion
Usi
ng C
lear
Pat
h R
ecei
ver
Wiri
ng D
iagr
am fo
r Rad
io
AN
TEN
NA
WH
ITE
(NO
T U
SED
)
24VA
C
VIO
LET
(N.O
.)
BRO
WN
(CO
MM
ON
)
76531
ON
/OFF
/HO
LD O
PEN
RO
CK
ER
SW
ITC
HP
/N 1
0-35
28
BLA
CK
WH
ITE
RE
DR
ED
BLA
CK
MS
SE
DC
O C
P/R
X R
ECEI
VER
OR
AN
GE
VIO
LET
WH
ITE
RED
BLA
CK
BR
OW
N
Off
On
Hol
d O
pen
Off
C
D
onon
HCTI
SWSE
LEC
TIO
N Y
TIM
E D
ELA
A
B
onon
HCTISW
SELE
CTI
ON
M
OD
E TIN
G
OPE
RA
CP
/RX
™
Cle
arP
ath
UG
SM
OD
ULE
PL
CP
/RXM
AD
D O
N
UG
PL
HA
RN
ESS
WIR
E
NO12
1110
9
8 5
6
7
2
3
4 1
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 33 www.NabcoEntrances.com 3/12/10
Power
(IF U
SE
D)
If m
agne
tic
lock
or f
ail s
afe
strik
e us
ed,
conn
ect l
ock
wire
s to
CO
M
and
N.C
. te
rmin
als
of
Mul
ti-M
odul
e
Not
e:1.
A b
lack
circ
le in
dica
tes
a w
ire c
onne
ctio
n.2.
P
ower
sup
ply
inpu
ts n
ot
pola
rity
sens
itive
.
STR
IKE
PO
WER
(To
mat
ch s
trike
vo
ltage
)
Term
inal
Stri
p on
Mag
num
Con
trol
BR
OW
N
BLA
CK
RED
WH
ITE
VIO
LET
OR
AN
GE
123456
RL1
RL2
LED
LED
24V
12V
N.O
.C
OM
N.C
.N
.C.
CO
MN
.O.
WET
1
WET
CO
MC
OM
DR
Y
DR
Y1D
RY2
WET
2W
ET3
RE
LAY1
REL
AY2
RAD
IOR
ECE
IVER
4-TE
RM
Power
COM
N.O.
STR
IKE
ELE
CTR
IC
TVS
Wire
Tra
nsie
nt
(sup
plie
d)di
rect
ly to
strik
e or
mag
net.
Vol
tage
Sup
pres
or
Not
pol
arity
sen
sitiv
e.
iti-2
00S
DN
030
2
SW
1M
OD
E SW
ITC
H
RE
LAY
2O
N T
IME
DO
O(D
ELAY
ON
OPE
RA
TE)
REL
AY 2
REL
AY 1
ON
TIM
E
MU
LTI M
OD
ULE
PN
14-
1224
0
120
VAC
24 V
AC
Tran
sfor
mer
P/N
14-
2101
24 V
AC
Nor
mal
ly O
pen
- Dry
Con
tact
sIN
TER
IOR
PU
SH S
WIT
CH
EX
TER
IOR
KE
Y S
WIT
CH
Nor
mal
ly O
pen
- Dry
Con
tact
s
Wir
ing
Dia
gram
for
4 W
ire
Rad
io R
ecei
ver
and
Ele
ctri
c St
rike
Figu
re 2
6
Magnum IV Control Manual for Gyro Tech Swing Door Systems
Page 34 www.NabcoEntrances.com 3/12/10
Act
ivat
ion
Dev
ice
durin
g al
arm
cont
acts
ope
nFi
re A
larm
TO N
.O &
CO
MM
ON
A
CTI
VAT
ION
TE
RM
INAL
S O
F D
OO
R C
ON
TRO
L DN
0058
PN
14-
1224
0M
ULT
I MO
DU
LE
Tran
sfor
mer
P/N
14-
2101
24 V
AC
24 V
AC12
0 VA
C
STR
IKE
PO
WER
(To
mat
ch s
trike
vol
tage
)
Not
e:1.
A b
lack
circ
le in
dica
tes
a w
ire c
onne
ctio
n.2.
P
ower
sup
ply
inpu
ts n
ot
pola
rity
sens
itive
.
If m
agne
tic
lock
or f
ail s
afe
strik
e us
ed,
conn
ect l
ock
wire
s to
CO
M
and
N.C
. te
rmin
als
of
Mul
ti-M
odul
e
iti-2
00S
Not
pol
arity
sen
sitiv
e.
Vol
tage
Sup
pres
or
strik
e or
mag
net.
dire
ctly
to(s
uppl
ied)
Wire
Tra
nsie
nt
TVS
ELE
CTR
ICS
TRIK
E
RE
LAY
2R
ELA
Y1
WET
3W
ET2
DR
Y2D
RY
1
DR
YC
OM
CO
MW
ET
WET
1N
.O.
CO
MN
.C.
N.C
.C
OM
N.O
.12
V24
V
LED
LED
RL2
RL1
Figu
re 2
7