Manual service Renault Scenic 2

7/22/2019 Manual service Renault Scenic 2

http://slidepdf.com/reader/full/manual-service-renault-scenic-2 1/93

© Renault s.a.s. 2006

"The repair methods given by the manufacturer in this document are based on the technical

specifications current when it was prepared.

The methods may be modified as a result of changes introduced by the manufacturer in theproduction of the various component units and accessories from which his vehicles areconstructed."

All copyrights reserved by Renault.

The reproduction or translation in part of whole of the present document, as well as the useof the spare parts reference numbering system, are prohibited without the prior writtenconsent of Renault.

NOVEMBER 2005 Edition Anglaise

X84, and J84

5 Mechanisms and accessories

51A SIDE OPENING ELEMENT MECHANISMS

52A NON-SIDE OPENING ELEMENT MECHANISMS

54A WINDOWS

55A EXTERIOR PROTECTION

56A EXTERIOR ACCESSORIES

57A INTERIOR ACCESSORIES

59A SAFETY ACCESSORIES



Scénic II - Section 5

Contents

Page

Scénic II - Section 5ContentsPage

51A SIDE OPENING ELEMENT MECHANISMS

Door exterior handle:Removal - Refitting 51A-1

Front side door lock barrel:Removal - Refitting 51A-7

Front side door lock:Removal - Refitting 51A-8

Rear side door lock:Removal - Refitting 51A-9

Front side door electricwindow mechanism:Removal - Refitting 51A-10

Rear side door electricwindow mechanism:Removal - Refitting 51A-11

52ANON-SIDE OPENING ELEMENTMECHANISMS

Sunroof operatingmechanism: Removal -Refitting 52A-1

Sunroof moving panel:Removal - Refitting 52A-4

Sunroof deflector: Removal -Refitting 52A-6

Fixed sunroof window:Removal - Refitting 52A-7

Sunroof sun visors: Removal- Refitting 52A-8

Fixed glass roof: Removal -Refitting 52A-10

Fixed glass sunroof visor:Removal - Refitting 52A-13

54A WINDOWS

Windscreen 54A-1

Sliding window in front sidedoor: Removal - Refitting 54A-4

Sliding window in rear sidedoor: Removal - Refitting 54A-6

Quarter panel light 54A-8

Rear screen glass: Removal- Refitting 54A-10

Opening rear screen glass:Removal - Refitting 54A-14

Fixed window in front door:Removal - Refitting 54A-19

Fixed glass roof frontwindow: Removal - Refitting 54A-22

Fixed glass roof rear window:Removal - Refitting 54A-24


Front bumper: Removal -Refitting 55A-1

Rear bumper: Removal -Refitting 55A-5

Front wheel arch liner:Removal - Refitting 55A-10

Rear wheel arch liner:Removal - Refitting 55A-11

Front door protective strip:Removal - Refitting 55A-12

B-pillar trims: Removal -Refitting 55A-13



Contents

Rear door protective strip:Removal - Refitting 55A-14

Scuttle panel grille: Removal- Refitting 55A-15

Tailgate moulding 55A-18

Roof protective strip:Removal - Refitting 55A-19

56A EXTERIOR ACCESSORIES

Door mirror: Removal -Refitting 56A-1

Door mirror glass: Removal -Refitting 56A-2

Door mirror casing: Removal- Refitting 56A-3

Rear number plate 56A-4

57A INTERIOR ACCESSORIES

Centre console: Removal -Refitting 57A-1

Interior rear-view mirrorRemoval - Refitting 57A-7

Grab handle: Removal -Refitting 57A-8

Sun visor: Removal -Refitting 57A-9

59A SAFETY ACCESSORIES

Front seat belt: Removal -Refitting 59A-1

Rear seat belt 59A-4

Centre rear seat belt:Removal - Refitting 59A-8



http://slidepdf.com/reader/full/manual-service-renault-scenic-2 4/9351A-1

SIDE OPENING ELEMENT MECHANISMS

Door exterior handle: Removal - Refitting 51AREMOVAL I - HANDLE EQUIPPED WITH HANDS-FREE

FUNCTION

Protect the trim (using a mastic knife for example).

Unclip the window winder plate (at the front) usingthe unclipping pliers, for the left-hand door.

Disconnect the connectors.

Note:

There are two possible procedures, dependingon the vehicle equipment.

101902

103803




Door exterior handle: Removal - Refitting 51A

Unclip the window winder plate (at the rear) using

the unclipping pliers, for the right-hand door.

Disconnect the connector.

Unclip the pull handle cover.

Remove the clips from inside the glove compart-

ment.

Reach into the glovebox.

Push your hand into the inner door box section up tothe glovebox clip area.

106328

103930

103929

114170





Remove the glovebox from its housing.

Remove the bolts (1) .

Unclip the trim flap using the unclipping pliers (pro-tecting the trim).

Remove the blanking cover.

Unlock the lock barrel retaining catch (2) , using ahook (locally produced: use a welding rod).

Disconnect the opening button male connector.

Unclip the handle module female connector.

114171

WARNING

Do not pull on the glovebox cover.

103931

1

101723

101986

2





Remove the « cover-lock barrel » assembly.

Move the handle, (3) and (4) .

Remove the handle with care, to avoid damaging the

connector.

II - HANDLE WITHOUT HANDS-FREE FUNCTION

Remove the blanking cover.

Unlock the lock barrel retaining catch (5) , using ahook (locally produced: use a welding rod).

101724

101836

4

3

101903

101723

5





Remove the « cover-lock barrel » assembly.

Remove the handle, (6) and (7) .

REFITTING

Check that the seal (8) is in place before refitting thehandle.

101724

101836

7

6

101838

8





Refit:

- the handle,

- . the lock barrel (9) .

Lock the catch (10) .

Carry out a manual function test on the lock barrel.

Proceed in the reverse order to removal.

101840

WARNINGIf necessary, replace the adhesive sealing foamaround the window winder plate connector toensure it is leaktight.

9

10




Front side door lock barrel: Removal - Refitting 51AREMOVAL

Remove the blanking cover to access the retainingcatch.

Unlock the lock barrel retaining catch (1) , using ahook (locally made: use a welding rod).

Remove the « lock barrel cover » .

REFITTING

Put the lock barrel in place (2) .

Lock the lock barrel retaining catch (3) with ascrewdriver.

Refit the blanking cover.

Carry out a manual function test on the lock barrel.

101723

101724

1

101840

3

2




Front side door lock: Removal - Refitting 51AREMOVAL

Remove:

- the door trim flap ( (see 72A, Side opening ele-ment lining) ),

- the exterior handle ( (see 51A, Side opening ele-ment mechanisms) ).

Remove the seal (1) .

Remove:

- the clip (2) ,

- the door panel module (3) ,

Disconnect the various connectors (depending on

equipment level).


Remove the lock and module assembly.

101838

101837

1

3

2

104447

104469

4 4




Rear side door lock: Removal - Refitting 51AREMOVAL

Remove:

- the door trim flap ( (see 72A, Side opening ele-ment lining) ),

- the exterior handle ( (see 51A, Side opening ele-ment mechanisms) ).

Remove the lock with the module.

Removing the presence sensor

Unclip the prism at (1) then (2) with a screwdriver.

REFITTING

Position the lock on the door box section retaininghook (3) .

Carry out a function test.


18697

2

1

18696

3




Front side door electric window mechanism: Removal - Refitting 51AREMOVAL

Remove the door trim ( (see 72A, Side opening ele-ment lining) ).

Position the window to gain access to the mountingclip (1) .

Remove the tab (1) by pushing it with a screwdriverand pulling the window upwards.

Lock the window in the fully closed position.

Disconnect the window winder motor.

Remove the motor mounting bolts (2) .

Remove the window winder motor.

REFITTING

For special notes on refitting the trim ( (see 72A,Side opening element lining) ).


Initialising the window winder motor:

- with ignition on,

- raise the window fully (the window rises jerkily),

- hold the switch (2 seconds),

- lower the window fully,


- the motor is initialised.

Note:

If replacing a door or carrying out any work onthe bodywork ( (see 47A, Side opening ele-ments) ).

103934

1

103936

2




Rear side door electric window mechanism: Removal - Refitting 51AREMOVAL



Remove the tab (1) by pushing it with a screwdriverand pulling the window upwards.

Lock the window in the fully closed position.

Disconnect the window winder motor.

Remove the motor mounting bolts (2) .

Remove the window winder motor.

REFITTING

For special no tes on refitting the trim ( (see 72A ,Side opening element lining) ).


Initialising the window winder motor:

- with ignition on,

- raise the window fully (the window rises jerkily),


- lower the window fully,


- the motor is initialised.

If replacing a door or carrying out any work onthe bodywork, (see 47A, Side opening ele-ments) .

103867

1

2

2



NON-SIDE OPENING ELEMENT MECHANISMS

Sunroof operating mechanism: Removal - Refitting 52A

REMOVAL

Lock the airbag computer using the diagnostic tool(see MR 366 Fault finding, 88C, Airbags and pre-tensioners ).

Remove the mobile panel from the sunroof (see52A, Non-side opening element mechanisms,Sunroof mobile panel: Removal - Refitting ).

Disconnect the battery (MR 371 Mechanical, 80ABattery, Battery: Removal - Refitting).

Remove the headlining (see 71A, Body interiortrim, Headlining ).

Carefully separate the indexing guide panels so thatthe cutting wire can pass through.

Unclip the side trims.

Detach the seal (1) .

Equipment required

diagnostic tool

Tightening torquesm

the centre cross mem-ber nuts

21 Nm

IMPORTANT

Before carrying out any work on or near a safetysystem component, lock the airbag computerusing the diagnostic tool. When this function isactivated, all the trigger lines are inhibited andthe airbag warning light on the instrument panelis lit continuously (ignition on).

IMPORTANT

Handling the pyrotechnic systems (airbags orpretensioners) near to a heat source or flame isprohibited: there is a risk of triggering the airbagsor pretensioners.

104317

102380

Note:

Fit a new seal, available in the reinstallation kitfrom the Parts Department, each time an old sealis removed.





Disconnect and unclip sunroof connector (2) .

Remove the centre cross member nuts (21 Nm)(3) .

Cut the cement bead around the periphery of the su-nroof operating mechanism.

This operation requires two people.

Pass the wire from (4) to (5) .

102379

102373

102371

Note:

When cutting the centre cross member cementbead, pass the cutting wire between the sunroofoperating mechanism and the centre cross mem-ber.





Pass the wire from (4) to (6) .

Put the cutting tool back in position.

Carry out the same operation on the other side of thecentre cross member.

Remove the sunroof operating mechanism.

REFITTING

For preparation and bonding (see Technical Note560A, General window bonding procedure ).

Position:

- the indexing guides on the sunroof operating me-chanism,

- . the positioning shims on the periphery of the sun-roof operating mechanism.

Using a special support (X2):

- Windscreen support: PARV 202,

- . Set of bars: APARV 200 ESP,

Attach the sunroof operating mechanism.

Balance up the clearances and shut lines.

A technician must be inside the vehicle to centre thesunroof with the indexing guides.

Remove the two indexing guides 30 minutes afterbonding the sunroof operating mechanism.


Unlock the airbag computer using the diagnostic

tool (see MR 372 Fault finding, 88C, Airbags andpretensioners ).

Connect the battery see (MR 370 Mechanical, 80A,Battery: Removal - Refitting).

Initialise the sunroof motor (see MR 370 Mechani-cal, 87D, Electric windows - Sunroof, Initialisa-tion ).

102370

WARNING

Always use « High Modulus » adhesive.




Sunroof moving panel: Removal - Refitting 52A

REMOVAL

Position the sunroof opening command in interme-diate opening position (1) .

Remove the bolts from the front of the mobile pa-

nel (5.6 Nm) (2) .

Remove the bolts from the rear of the mobile pa-nel (5.6 Nm) (3) .

Remove the mobile panel (this operation requires

two people).

Tightening torquesm

bolts from the front of

the mobile panel

5.6 Nm

bolts from the rear ofthe mobile panel

5.6 Nm

101983

102378

102381




Sunroof moving panel: Removal - Refitting 52AREFITTING

When removing and refitting the mobile panel, putsome « Frenbloc » on the mounting bolts.

When replacing a mobile panel, replace the bolts

with the bolts supplied with the mobile panel.


Initialise the sunroof motor (see MR 370 Mechani-cal, 87D, Electric windows - Sunroof, Electric su-nroof: Initialisation) ,




Sunroof deflector: Removal - Refitting 52A

REMOVAL

Open the moving panel.

Remove the deflector bolts (2 Nm) (1) whilst sup-porting the deflector.

Remove the air deflector.

REFITTING

When removing and refitting the deflector, put some« Frenbloc » on the mounting bolts.

When replacing a deflector, replace the bolts withthe bolts supplied with the deflector.


Initialise the sunroof motor (see MR 370 Mechani-cal, 87D, Electric windows - Sunroof, Electric su-nroof: Initialisation) ,

Tightening torquesm

deflector bolts 2 Nm

102372




Fixed sunroof window: Removal - Refitting 52A

REMOVAL

Lock the airbag computer using the diagnostic tool(see MR 372 Fault finding, 88C, Airbags and pre-tensioners ).

Disconnect the battery (see MR 370 Mechanical,

80A Battery, Battery: Removal - Refitting ).Remove the headlining (see 71A, Body interiortrim, Headlining ).


Protect:

- the glazing frame and the rear section of the roofwith masking tape,

- . the inside of the vehicle.

Then cut the cement bead.


REFITTING

For preparation and bonding, (see Technical Note

560A, General window bonding procedure ).

Position the new shims supplied with the fixed glasson the periphery of the sunroof operating mecha-nism.

Refit the side trim pieces.

Cement the fixed window.This operation requires two people.

Respect the following clearances and shut lines:

- « fixed window mobile panel » : 7 mm ,

- « fixed window - trims » : balance the side clearan-ces.


Unlock the airbag computer using the diagnostictool (see MR 372 Fault finding, 88C, Airbags andpretensioners ).

Connect the battery (see MR 370 Mechanical, 80ABattery: Removal - Refitting ).

Equipment required

diagnostic tool

IMPORTANT

Before carrying out any work on a safety or proxi-mity system component, lock the airbag compu-ter using the diagnostic tool. When this functionis activated, all the trigger lines are inhibited andthe airbag warning light on the instrument panelis lit continuously (ignition on).

IMPORTANT

Handling the pyrotechnic systems (airbags orpretensioners) near to a heat source or flame isprohibited: there is a risk of triggering the airbagsor pretensioners.

104317

104685

WARNING

Always use « High Modulus » adhesive.




Sunroof sun visors: Removal - Refitting 52A

REMOVAL

Lock the airbag computer using the diagnostic tool(see MR 372 Electrical fault finding, 88C, Airbagsand pretensioners ).

Disconnect the battery see (MR 370 Mechanical,80A Battery, Battery: Removal - Refitting).

Remove the headlining (see 71A, Body interiortrim, Headlining) .

Remove the sun visor bolts (2 Nm) (1) .

Unclip the visor (2) .

Partially remove the visor.

Equipment required

diagnostic tool

Tightening torquesm

sun visor bolts 2 Nm

IMPORTANT

Before carrying out any work on a safety or proxi-mity system component, lock the airbag compu-ter using the diagnostic tool. When this functionis activated, all the trigger lines are inhibited and

the airbag warning light on the instrument panelis lit continuously (ignition on).

IMPORTANT

Handling pyrotechnic systems (airbags or preten-sioners) near to a source of heat or flame is for-bidden: there is a risk of triggering the airbags orpretensioners.

102374

102377




Sunroof sun visors: Removal - Refitting 52A

Remove guide pad (3) .

Remove pressure pads (4) .

Remove the blind.

REFITTING


Unlock the airbag computer using the diagnostictool (see MR 372 Fault finding, 88C, Airbags andpretensioners ).

Connect the battery (see MR 370 Mechanical, 80ABattery: Removal - Refitting ).

102375

102376

WARNING

When refitting blinds, take care to insert the blindfabric with the guide pads in the side runners.




Fixed glass roof: Removal - Refitting 52A

REMOVAL

I - REMOVAL PREPARATION OPERATION

Lock the airbag computer using the diagnostic tool(see MR 372 Fault finding, 88C, Airbags and pre-tensioners, Airbag computer locking procedure).

Disconnect the battery (see MR 370 Mechanical,80A, Battery, Battery: Removal - Refitting ).

Remove:

- the headlining (see 71A, Body internal trim, Hea-dlining: Removal - Refitting ).

- the roof protection strips (see 55A, Exterior pro-tection, Roof protection strip: Removal - Refit-ting ).

Protect:

- the area around the fixed glass roof with maskingtape,

- the seal (1) .

Remove the nuts (2) from the centre cross member.

II - OPERATION FOR REMOVAL OF PARTCONCERNED

Cut the cement bead.


Equipment required

diagnostic tool

Tightening torquesm

centre cross membernuts

21 Nm

IMPORTANT

Before carrying out any work on or near a safetysystem component, lock the airbag computer usingthe diagnostic tool. When this function is activa-ted, all the trigger lines are inhibited and the airbagwarning light on the instrument panel is conti-nuously lit (with the ignition on).

IMPORTANT

Handling pyrotechnic systems (airbags or preten-sioners) near to a source of heat or flame is forbid-den: there is a risk of triggering the airbags orpretensioners.

116576

102373




Fixed glass roof: Removal - Refitting 52A

Pass the cutting wire from (3) to (4) .

Pass the cutting wire from (5) to (6) .

Put the cutting tool back in position.

Carry out the same operation on the other side of thecentre cross member.

Remove the fixed glass roof using the following spe-cial supports (X2):

- Support: PARV 202 ,

- Set of arch supports: APARV 200 ESP .

This operation requires four people.

REFITTING

I - REFITTING PREPARATION OPERATION

For preparation and bonding of the fixed glass roof(see Technical Note 560A, General bonding pro-cedure for windows and sunroof ).

Position:

- the indexing guides on the fixed glass roof,

- the positioning shims on the edge of the fixed glass

roof.

II - REFITTING OPERATION FOR PARTCONCERNED

Apply the cement bead to the inside edge of the roof

or to the fixed glass roof moulding.

Bond the fixed glass roof using special supports.

This operation requires four people.

102371

Note:

When cutting the centre cross member cementbead, pass the cutting wire between the fixedglass roof and the centre cross member.

102370

116576

Note:

Replace the seal (7) if it was damaged duringremoval.

Note:

It is essential to use high modulus adhesive forbonding the fixed glass roof.




Fixed glass roof: Removal - Refitting 52ACheck that the positioning shims on the fixed glassroof moulding make contact with the roof.

Remove the two indexing guides 30 minutes afterbonding the fixed glass roof.

III - FINAL OPERATION

Refit the nuts to the centre cross member.

Torque tighten the centre cross member nuts (21Nm) .

Refit:


- the headlining (see 71A, Body internal trim, Hea-

dlining: Removal - Refitting ).

Connect the battery (see MR 370 Mechanical, 80A,Battery, Battery: Removal - Refitting ).

Unlock the airbag computer using the diagnostictool (see MR 372 Fault finding, 88C, Airbags andpretensioners, Airbag computer locking proce-dure ).




Fixed glass sunroof visor: Removal - Refitting 52A

REMOVAL


Lock the airbag computer using the diagnostic tool(see MR 372 Fault finding, 88C, Airbags and pre-tensioners, Airbag computer locking procedure).


Remove the headlining (see 71A, Body internaltrim, Headlining: Removal - Refitting ).


Remove the bolts from the sun visor (1) .

Unclip the sun visor.

Partially remove the sun visor.

Remove the guide mechanism (2) from the siderails.

Equipment required

diagnostic tool

Tightening torquesm

sun visor bolts 2 Nm

IMPORTANT


IMPORTANT


102374

102375




Fixed glass sunroof visor: Removal - Refitting 52A

Remove the sliding mechanism (3) from the siderails.

Remove the sun blind.

REFITTING

I - REFITTING OPERATION FOR PARTCONCERNED

Insert the side rails:

- the sliding mechanism,

- the guide mechanism.

Clip the sun visor into place.

Refit the bolts (1) to the sun visor.

Torque tighten the sun visor bolts (2 Nm) .

Carry out a function test.

II - FINAL OPERATION

Refit the headlining (see 71A, Body internal trim,Headlining: Removal - Refitting ).


Unlock the airbag computer using the diagnostictool (see MR 372 Fault finding, 88C, Airbags andpretensioners, Airbag computer locking proce-dure ).

102376



WINDOWS

Windscreen 54A

REMOVAL

Remove:

- the windscreen pillars ( (see 71A , Body interior

trim) ),

- the interior rear-view mirror ( (see 57A, Interior ac-cessories) ),

- the cowl grille ( (see 55A, Exterior protection) ).

Unclip the windscreen frame seal.

Protect the windscreen surround and the headlining

with masking tape.

Position the dashboard protector (Car. 1704).

Cut the cement bead.

REFITTING

Position the three lower shims (1) .

Fit the new frame seal on the windscreen.

For preparation and bonding, see Technical Note560A .

Use the proper cement bead size.

Special tooling required

Car. 1704 J84 Dashboard pro-tector

WARNING

- If the vehicle is fitted with a rain detector, thereplacement windscreen must be the samecolour. This could otherwise affect the operationof the rain detector. For further information,refer to (see 88B, Multiplexing) .

- Leave the rain detector in place on the old

windscreen throughout the replacement opera-tion.

Note:

When « removing - refitting » or replacing, theseal and positioning shims must be systemati-cally replaced. These parts are available at retail.

104442

103754

WARNING

Be sure to use high modulus adhesive to bondthe windows: monopac + 2 (part no.: 77 11 218570 ) and additional cartridge (part no.: 77 11218 571 ).

5418

11



WINDOWS

Windscreen 54A

Observe the following clearance and flushness va-

lues:

- « windscreen - roof » ,

- « windscreen - A-pillar » .

REMOVAL

SPECIAL NOTES ON REMOVING AND REFITTINGTHE RAIN DETECTOR

Remove both detector mountings.

Remove the detector from the windscreen.

104443

WARNINGThe rain detector should be handled in totally

clean conditions, any dust or cloth residue couldcause the detector to malfunction.

101630

Note:

When replacing the windscreen, be sure toreplace section (2) of the rain detector. This part

is available at retail from the Parts Department.



WINDOWS

Windscreen 54A

Remove the three clips (4) .

Separate the two sections.

REFITTING

Assemble the (new) adhesive base and the unit.

Clip the assembly to the windscreen ring.


102446

Note:

The rain detector comprises two sections:

- the adhesive base (2) ,

- the printed circuit unit (3) .

2

3

4 4



WINDOWS

Sliding window in front side door: Removal - Refitting 54A

The glass may be replaced by two procedures:

- if the glass has been scratched or dented, see the firstprocedure,

- if the glass is broken, see the second procedure.

REMOVAL: PROCEDURE ONE

Remove the door flap ( (see 72A, Side opening ele-ment lining) ).

Remove the exterior weatherstrip ( (see 66A, Win-dow sealing) ).

Position the window to gain access to the mounting

clip (1) .

Press on the tab (1) with a screwdriver and pull thewindow upwards.

Remove the frame seal behind the panel (2) .

Remove the window via the outside of the door.

REFITTING


Note:

If replacing a door or carrying out any work on thebodywork, ( (see 47A, Side opening elements) ).

104448

1

104435

Note:

It is not necessary to remove the frame sealcompletely.

104433

2



WINDOWS

Sliding window in front side door: Removal - Refitting 54AREMOVAL: PROCEDURE TWO


Vacuum up the splinters of glass in the door boxsection.

Clean:

- inside the frame seal,

- the window winder moving slides.

REFITTING

Partially remove the frame seal to slide the glass outvia the exterior of the vehicle.

Fit the glass at the mounting clip (3) .

Clip the glass onto the clip.


Note:

For the second procedure, the door trim must beremoved to vacuum up the splinters of glass andto clean the window winder moving slides.

104433

103934

3



WINDOWS

Sliding window in rear side door: Removal - Refitting 54A

The glass may be replaced by two procedures:

- if the glass has been scratched or dented, see the firstprocedure.

- if the glass is broken, see the second procedure.

REMOVAL: PROCEDURE ONE

Remove the trim flap ( (see 72A, Side opening ele-ment lining) ).


Position the window to gain access to the mounting

clip (1) .

Press on the tab (1) with a screwdriver and pull theglass upwards.

Remove:

- the slide bolts (2) ,

- the slide by pressing on the tab (2) .

Remove the window via the outside of the door.

REFITTING


Note:

If replacing a door or carrying out any work on thebodywork, ( (see 47A, Side opening elements) ).

103953

1

103872

Note:

It is not necessary to remove the frame seal.

103884

2



WINDOWS

Sliding window in rear side door: Removal - Refitting 54AREMOVAL: PROCEDURE TWO

Remove the trim ( (see 72A, Side opening elementlining) ).


Vacuum up the splinters of glass in the door boxsection.

Clean:

- inside the slide frame seal,

- the window winder moving slide.

REFITTING

Remove:

- the slide bolts (3) ,

- the slide by pressing on the tab (4) .

Slide the window to the outside of the door.

Fit the glass at the mounting clip (5) .

Clip the glass onto the clip.

Refit the slide.


Note:

For the second procedure, the door trim must beremoved to vacuum up the splinters of glass.

103877

Note:

It is not necessary to remove the frame seal.

3

4

103884

103867

5



WINDOWS

Quarter panel light 54AREMOVAL

Remove:

- the wheel arch interior trim ( (see 70A, General Ve-hicle Information) ),

- the rear quarter panel trim ( (see 71A, Body inte-rior trim) ).

Protect the rear quarter window surround (with mas-king tape).


Protect the rear quarter window surround (with mas-king tape).


REFITTINGFor preparation and bonding, see Technical Note560A .

STANDARD CHASSIS

104444

Note:

- When carrying out any work on the bodywork,protect the seal with a spatula when cutting.

- The glass is supplied for replacements as aspare part with its moulded seal.

LONG CHASSIS

107123

Note:

- When carrying out work on the bodywork, pro-tect the seal with a spatula when cutting.

- The rear quarter window is supplied for replace-ments as a spare part with its moulded seal,from the Parts Department.

WARNING

Be sure to use high modulus adhesive to bondthe windows: monopac + 2 (part no.: 77 11 218570 ).



WINDOWS

Quarter panel light 54A

Position the shims (1) .

Bond the window.

Observe the clearance and flushness values.

Position the shims (2) .

Bond the window.

Extract the shims (2) , after the recommended bon-ding drying time.

Observe the clearance and flushness values.

STANDARD CHASSIS

103755

11

LONG CHASSIS

107241

2 2



WINDOWS

Rear screen glass: Removal - Refitting 54A

REMOVAL

PROCEDURE FOR REMOVING NON-OPENING

REAR SCREENRemove the tailgate trim ( (see 73A, Non-side ope-ning element lining) ).

Remove the tailgate trim.

Remove:

- the wiper arm nut cover,

- the nut,

- the wiper arm using tool (Ele. 1294-01).

Disconnect:

- the connector,

- the two rear screen heating supply terminals.

Remove:

- the motor bolts (1) ,

- the motor.


Ele. 1294-01 Windscreen wiper armremoving tool.

Tightening torquesm

wiper arm nut 12 Nm

motor mounting nuts 8 Nm

103741

103540

103536

11



WINDOWS


Remove the seal (2) .

Removing the brake light

Unclip the light from inside using a flathead

screwdriver on the two metal clips (3) (illustration be-low).

Remove the light via the outside.

103538

103535

2

3

103534

104508



WINDOWS


Unclip the jet (two clips) with a flathead screwdriver.



REFITTING

Always replace the shims.

For preparation and bonding, see Technical Note560A .

Use the proper cement bead size.

Bond the screen; this operation requires two people.

104506

104507

104445

103756



WINDOWS


Respect the following clearance and flushness va-

lues:

- « rear screen - roof » ,

- « rear screen - quarter panel » .

Special notes on refitting the wiper motor

Clean the motor shaft splines.

Position the wiper arm in the rest position, with a

new nut at (4) a distance of 42 mm from the edge ofthe rear screen.

Torque tighten:

- the wiper arm nut (12 Nm) ,

- the motor mounting nuts (8 Nm) .

104445

103538

WARNING

- Replace the seal whenever the motor is remo-ved.

- Check that the motor is in the park positionbefore refitting the wiper arm.

103537

4



WINDOWS

Opening rear screen glass: Removal - Refitting 54A

REMOVAL

PROCEDURE FOR REMOVING OPENING REARSCREEN

Remove the tailgate trim ( (see 73A, Non-side ope-ning element lining) ).

Remove:

- the wiper arm nut cover,

- the nut,

- the wiper arm using tool (Ele. 1294-01).

Remove:

- the nut cover,

- the nut,

- the trim.

Remove the nut.


Ele. 1294-01 Windscreen wiper armremoving tool.

Tightening torquesm

motor shaft nut 6.5 Nm

adjustment plate nut 4.5 Nm

wiper arm nut 12 Nm

103540

100077

104629



WINDOWS


Remove:

- the two bolts,

- the tailgate trim.

Remove the two trim upper bolts.

Remove:

- the two trim lower nuts,

- the trim.

Disconnect the rear screen heating terminals.

103741

104525

104505



WINDOWS


Remove:

- the hinge bolt,

- the rear screen heating wire from above.

REFITTING

Adjusting the wiper mechanism

104519

104522

WARNING

When removing the rear screen, do not damagethe hinges seal (the hinges are supplied as spareparts with seals).

WARNING

When replacing an opening rear screen, be sureto visually check the clearances before followingthe procedure ( (see 40A, General VehicleInformation) ).

104632

WARNING

Be sure to replace the seal.



WINDOWS


Position the mechanism, keeping a distance (2) of

40 mm between the trim and the edge of the rearscreen.

Partially tighten the nut (1) .

Centre the mechanism in relation to mounting bolt(3) .

Torque tighten:

-the motor shaft nut (6.5 Nm) (1) ,

-the adjustment plate nut (4.5 Nm) (3) .

Position the wiper arm at (4) a distance of 42 mmfrom the edge of the rear screen.

104630

104627

2

1

3

104521

WARNING

- Close the opening rear screen (mechanismpositioned on the motor plate).

- Operate the rear screen wiper to engage themechanism on the motor plate. Make sure that

the motor is in the « park » position.

103537

4



WINDOWS


Torque tighten the wiper arm nut (12 Nm) .

104628

Note:

You can fine-tune the wiper arm setting by tur-ning the mechanism as show in the illustrationabove.



WINDOWS

Fixed window in front door: Removal - Refitting 54AREMOVAL

Remove:

- the front door trim ( (see 72A, Side opening ele-ment lining) ),

- the exterior weatherstrip ( (see 66A, Window sea-ling) ).


Press on the tab (1) with a screwdriver and pull thesliding window upwards.

Remove the frame seal behind the panel (2) .

Remove the sliding window via the outside of the

door.

Unclip the interior frame trim.

103934

104435

1

2

104433

103937



WINDOWS

Fixed window in front door: Removal - Refitting 54A

Unclip the interior frame trim.

Unclip the interior weatherstrip.

Remove the fixed upright lower bolt (3) .

Remove:

- the fixed upright upper bolt (4) ,

- the frame seal as far as the fixed window.

103938

103939

103941

103940

3

4



WINDOWS

Fixed window in front door: Removal - Refitting 54A

Unclip the full length of the seal.

Remove the « frame seal - fixed window - fixedupright » assembly.

Remove the window seal.

REFITTING

Make sure the foam pads are in place on the fixedwindow behind the panel (5) .


103942

5



WINDOWS

Fixed glass roof front window: Removal - Refitting 54A

REMOVAL


Lock the airbag computer using the diagnostic tool(see MR 372 Fault finding, 88C, Airbags and pre-

tensioners, Airbag computer locking procedure).


Remove:



Protect:

- the fixed glass roof front window surround usingmasking tape,

- the front roof section using masking tape,

- the inside of the vehicle.


Begin cutting the cement bead.


Remove the fixed glass roof front window.

REFITTING


For preparation and bonding of the fixed glass rooffront window (see Technical Note 560A, General

window and sunroof bonding procedure ).

Place the new positioning shims on the fixed glassroof moulding.

Equipment required

diagnostic tool

IMPORTANT


IMPORTANT


116577

116575



WINDOWS

Fixed glass roof front window: Removal - Refitting 54A

Detach the seal (1) .

Affix the new seal (1) .

Refit the roof protection strips (see 55A, Exteriorprotection, Roof protection strip: Removal - Re-fitting ).

II - REFITTING OPERATION FOR PART

CONCERNED

Bond the fixed glass roof front window using the fol-

lowing special supports:

- Support: PARV 202 ,

- Set of arch supports: APARV 200 ESP .


Maintain the clearance between the fixed glass roof

front window (2) and the fixed glass roof rear window(3) , (7 mm).

The fixed glass roof front window (2) should be sli-ghtly higher than the fixed glass roof rear window (3).

Arrange the lateral clearances so that they areequal.

III - FINAL OPERATION

Refit the headlining (see 71A, Body internal trim,Headlining: Removal - Refitting )


Unlock the airbag computer using the diagnostictool (see MR 372 Fault finding, 88C, Airbags andpretensioners, Airbag computer locking proce-

dure ).

116576

Note:

Fit a new seal, available in the reinstallation kitfrom the Parts Department, each time an old sealis removed.

Note:

It is essential to use high modulus adhesive forbonding the fixed glass roof front window.

113525



WINDOWS

Fixed glass roof rear window: Removal - Refitting 54A

REMOVAL


Lock the airbag computer using the diagnostic tool(see MR 372 Fault finding, 88C, Airbags and pre-

tensioners, Airbag computer locking procedure).


Remove:



Protect:

- the fixed glass roof rear window surround usingmasking tape,

- the rear roof section using masking tape,

- the inside of the vehicle.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

Begin cutting the cement bead.


Remove the fixed glass roof rear window.

REFITTING


For preparation and bonding of the fixed glass roof

rear window (see Technical Note 560A, General

window and sunroof bonding procedure ).

Place the new positioning shims on the fixed glass

roof moulding.

Refit the roof protection strips (see 55A, Exterior

protection, Roof protection strip: Removal - Re-

fitting ).

Equipment required

diagnostic tool

IMPORTANT


IMPORTANT


116579

116578





EXTERIOR PROTECTION

Front bumper: Removal - Refitting 55AREMOVAL



Unclip the plastic rivets (3) .

Unclip the side section of the bumper.

Partially detach the bumper.

Disconnect:

- the fog lights connector,

- the headlight washer jet pipe.

103589

103590

11

2

2

104355

103621

3 3



EXTERIOR PROTECTION

Front bumper: Removal - Refitting 55ASTRIPPING

Remove:

- the upper bolts,

- the grille side bolts (4) .

Press on the clips.

Detach the « reinforcement - radiator grille » assem-bly forwards.

Unclip the radiator grilles from the reinforcement.

Remove the fog lights wiring harness.

Remove the clips (5) with a screwdriver.

Remove the absorbers.

Remove the two fog light bolts.

Remove the fog lights.

103757

103763

4

4

103758

103759

5



EXTERIOR PROTECTION

Front bumper: Removal - Refitting 55A

Remove the bolts.

Unclip the monogram.

Unclip the clips.

Remove the centre grille.

Unclip the clips.

Remove the outer strip.

Drill the rivets out.

Remove:

- the deflector,

- the aerodynamic fins.

103760

103761

103762

103764



EXTERIOR PROTECTION

Front bumper: Removal - Refitting 55AREFITTING

ADAPTING THE SPARE PART FOR FITTING THEHEADLIGHT WASHER JETS

Use:

- a 3 mm diameter drill bit to drill the index hole (6) ,

- a 3 mm diameter drill bit to drill the pilot hole, andfinish the operation with a dovetail cutter for the jethole (7) .

Before refitting the washer jets, check that the seal is

in place.

Tighten the nut slightly.

Connect the headlight washer pipe and the fog lightsconnector.


Note:

Before painting, drill the bumper following themarkings if it has headlight washer jets.

101949

6

7

101951



EXTERIOR PROTECTION

Rear bumper: Removal - Refitting 55A

REMOVAL

Mount the vehicle on a lift.

Remove the lower bolts.


Unclip the boot stop trim.

Remove:

- the adjustable stops,

- the bumper upper bolts.

Tightening torquesm

cross member side

bolts

35 Nm

103740

103742

1

103734

103735



EXTERIOR PROTECTION


Remove the rear lights.


Remove the plastic rivets (2) .

Disconnect the parking aid sensor wiring harness

connector (depending on equipment level).

Unclip the bumper.

Remove the bumper towards the rear.

I - REPLACING THE OUTER STRIP

103167

103736

2

104457

103737

Note:

The outer strip is available as a spare part.



EXTERIOR PROTECTION


Unclip the parking aid sensors (depending on equip-

ment level).

Release the wiring harness.

Unclip:

- the clips,

- the reflector.

Remove the side strip.

Unclip the clips.

Remove the centre strip.

II - REPLACING THE IMPACT ABSORBERS

Remove the absorber bolt from the cross member.

104456

103738

103739

103907



EXTERIOR PROTECTION


Remove:

- the cross member side bolt (3) ,

- the cross member.

Drill out the four rivets.

Remove the bumper support.

Rivets part no.: 77 03 072 051 .

Drill the rivets out (4) .

Remove:

- the bolts (5) ,

- the adjustable stop support.

Adapting the bumper for fitting the parking aidsensors

103908

103910

3

103909

The special outer strip is available as a sparepart.

4

5 5



EXTERIOR PROTECTION


Refit the special strip on the bumper.

Clip the parking aid sensors into their housing.

Clip the harness on the bumper.

REFITTING

Torque tighten the cross member side bolts (35Nm) .


104456





EXTERIOR PROTECTION

Rear wheel arch liner: Removal - Refitting 55AREMOVING - REFITTING

REAR WHEEL ARCH

Remove:

- the bolts (1) ,

- the nuts (2) .

Remove the nuts (3) .

Unclip the clip (4) using the unclipping pliers.

Remove the wing interior protector.

REFITTING


103743

103744

1

2

3

3

4



EXTERIOR PROTECTION

Front door protective strip: Removal - Refitting 55AREMOVAL

Remove the blanking cover (1) .

Press on the locking catch with a screwdriver.

Slide the moulding to the rear of the vehicle (2) .

REFITTING


104441

104314

1

2

104313

IMPORTANT

Before refitting the mouldings, pull out the lockingcatches slightly (3) .

3



EXTERIOR PROTECTION

B-pillar trims: Removal - Refitting 55AREMOVAL

Remove the bolt (1) .

Unclip the trim (2) .

REFITTING

Check that the clips are secure.


104316

1

2

2



EXTERIOR PROTECTION

Rear door protective strip: Removal - Refitting 55A

REMOVAL

Insert tool (Car. 1363) , and apply gentle pressure.Slide the moulding towards the front of the vehicle.

REFITTING



Car. 1363 Door mirror glassremoval tool.

104315

20866

IMPORTANT

Before refitting the mouldings, pull out the lockingcatches slightly.



EXTERIOR PROTECTION

Scuttle panel grille: Removal - Refitting 55A

REMOVAL


Remove:

- the side seals (1) ,

- the bonnet seal.

Remove the bolts.

Remove the cowl half-grille.


Ele. 1552 Tool for removing therear screen wiper arm.

Tightening torquesm

wiper arm nuts 21 Nm

103635

103629

103630

1



EXTERIOR PROTECTION


Remove the wiper arms using tool (Ele. 1552).

Remove the bolts.

Remove the bolt.

Remove the cowl grille.

REFITTING

103631

103636

103632

Note:

- Replace the plastic inserts for the cowl grillemounting bolts each time they are removed.

- Before refitting the cowl grille, clean the lowersection of the windscreen.



EXTERIOR PROTECTION


Clip on the cowl grille.

Tighten the bolts.

Position the wiper arms according to the markings

on the windscreen.

Torque tighten the wiper arm nuts (21 Nm) .

103633

103623

WARNING

Be sure to check that the motor is in the parkposition before refitting the wiper arms.

Note:

The cowl grille trim support can be removed if itneeds to be replaced.

103628



EXTERIOR PROTECTION

Tailgate moulding 55AREMOVAL

Remove the four trim bolts.

Unclip:

- the lock cover,

- the centre trim.

Remove the two bolts (1) .

Disconnect the connector (2) .

Gently remove the strip.

Unclip the opening control and the two lights.

Disconnect the various connectors.

REFITTING


103543

104465

1

2

103915

Note:

There is a sealant mastic bead (3) between thestrip and the tailgate.

104450

3



EXTERIOR PROTECTION

Roof protective strip: Removal - Refitting 55AREMOVAL

Carefully unclip the trim.

REFITTING

Clip the moulding in place along its entire length.


Note:

- The headlining vary according to the equipmentlevel (sunroof).

- Removal is the same for both versions.

104317

104318

Note:

The access flaps to the roof bar mountings canbe replaced, and are available at retail as spareparts.

104320

Note:

The trim mounting clips can be replaced, and areavailable at retail as spare parts.

104319



EXTERIOR ACCESSORIES

Door mirror: Removal - Refitting 56AREMOVAL

Remove:

- the rear view mirror glass ( (see 56A, Exterior ac-cessories) ),

- the rear-view mirror casing ( (see 56A, Exterioraccessories) ).

Remove the bolt (1) .

Remove:

- the bolt (2) ,

- the rear-view mirror.


REFITTING

Check that the soundproofing foam is in place and ingood condition before refitting the rear-view mirror.


104684

104683

1

2




Door mirror glass: Removal - Refitting 56A

REMOVAL

Protect the edge of the rear-view mirror (masking ta-pe).

Use tool (Car. 1363) as a lever to unclip the glass.

Disconnect the supply terminals.

REFITTING

Connect the terminals.

Offer up the glass in position.

Clip the glass in place.


Car. 1363 Door mirror glassremoval tool.

101622




Door mirror casing: Removal - Refitting 56AREMOVAL

Remove the rear view mirror glass ( (see 56A, Exte-rior accessories) ).

Unclip the retaining clips with a flathead screwdriver.

Fold in the rear-view mirror.

Remove the casing (1) .

REFITTING

Check the condition of the retaining clips before refit-ting the casing.

Offer up the casing in position.

Clip the casing in place.

Refit the rear view mirror glass.

101623

104439

1

104438





INTERIOR ACCESSORIES

Centre console: Removal - Refitting 57A

REMOVAL

I - ENTRY LEVEL CONSOLE WITH AUTOMATICPARKING BRAKE

Remove the carpet with a flathead screwdriver.

Remove:

- the mounting bolts (1) ,

- the nuts (2) ,

- the console.

II - ENTRY LEVEL CONSOLE WITH MANUALPARKING BRAKE

Remove the carpet with a flathead screwdriver.

Tightening torquesm

nuts 8 Nm

mounting bolts 8 Nm

plate nuts 21 Nm

103593

103594

104533

1

2





Remove:

- the mounting bolts (3) ,

- the nuts (4) ,

- the console.

III - TOP END CONSOLE

Move the arm rest to the angular position (5) asshown in the above diagram.

Remove the armrest (6) .

104534

3

4

103480

104135

6

5





Remove the blanking cover (7) using a flathead

screwdriver.

Move the console to the rear position.

Remove:

- the upper mounting bolts (8) ,

- the rear side bolts.

Move the console to the forward position.

Remove the front side bolts.

Unclip:

- the trim (9) ,

- the side moulding (10) ,

- the ashtray holder.

104134

104136

7

8

104137

104141

10 10

9





Remove the support bolts (11) .


Remove the console.

Remove the plate nuts.

STRIPPING

Open the storage compartment flap.

Remove the console lining, pulling it up and off.

104140

104139

11

104138

104127





Remove the arm rest support.

Unclip the two lights using a flathead screwdriver.

Press on the clip (12) with a flathead screwdriver.


Remove the console control unit.

Move the side walls apart slightly (13) to remove thecurtain from the runners (14) .

104129

104128

12

104130

104131

1413

13





Unclip the runners.

Remove:

- the springs from their housing (mark where theyare fitted before removal),

- the plastic pins.

REFITTING

Torque tighten:

-the nuts (8 Nm) ,

-the mounting bolts (8 Nm) ,

- the plate nuts (21 Nm) .


104132

104133




Interior rear-view mirror Removal - Refitting 57AREMOVAL

Unclip the upper casing (1) .

Unclip the lower casing (2) .


Remove the rear-view mirror (3) .

REFITTING


101715

101716

1

2

101717

Note:

When removing the rear-view mirror, watch outfor the nearby rain sensor to avoid damaging it.

3




Grab handle: Removal - Refitting 57A

REMOVAL

Unclip the two mounting pins (1) using tool (Car.1597).

Remove the part by pulling it off by hand from above.

REFITTING



Car. 1597 Lever for removingrear grab handle clips.

100183

1




Sun visor: Removal - Refitting 57AREMOVAL

Unclip the mounting clip (1) .

Remove:

- the clip (2) ,

- the sun visor (3) .

Unclip the mounting clip (4) .

Use the screwdriver (5) to unclip the clip.

Remove the assembly.

Disconnect the various connectors (according to theequipment level).

REFITTING


104357

104356

1

3

2

101718

5

4



SAFETY ACCESSORIES

Front seat belt: Removal - Refitting 59A

REMOVAL

Move the front seat forward.

Undo the seat belt by pressing the catch (1) .


Unclip the upper section of the trim (2) .

Remove the trim (3) .

Partially remove the door seals.

Unclip the lower retaining clips (4) .

Tightening torquesm

seat belt mounting bolts 21 Nm

IMPORTANT

In case of doubt on how a safety system compo-nent is activated ( (see 03B, Impact) ).

18828

1

104145

104143

3

2

4



SAFETY ACCESSORIES

Front seat belt: Removal - Refitting 59A

Remove:

- the trim (5) and (6) ,

- the seat belt web via the aperture (7) .

Remove the seat belt anchorage bolt (8) .

Remove:

- the inertia reel bolt (9) ,

- the inertia reel.

Remove:

- the seat belt height adjustment mechanism moun-ting bolt (10) ,

- the assembly up and off.

REFITTING

Torque tighten the seat belt mounting bolts (21Nm) .

104146

104144

6

5

7

8

104207

104142

9

10



SAFETY ACCESSORIES

Front seat belt: Removal - Refitting 59AProceed in the reverse order to removal.



SAFETY ACCESSORIES

Rear seat belt 59A

REMOVAL

Remove the rear seats.


Unclip the upper section of the trim (1) .

Remove the trim (2) .

Unclip the trim (3) and (4) .

Equipment required

diagnostic tool

Tightening torquesm


side stalk bolts 21 Nm

centre stalk bolts 44 Nm

STANDARD CHASSIS

IMPORTANT

- In case of doubt on how a safety system com-ponent is activated ( (see 03B, Impact) ).

- Before carrying out any work on a safety sys-tem component, lock the air bag computerusing the diagnostic tool ( (see 8, Electricalequipment) ). When this function is activated,all the trigger lines are inhibited and the air bag

warning light on the instrument panel lights upcontinuously (ignition on).

104359

104360

1

2

3

4



SAFETY ACCESSORIES

Rear seat belt 59A

Unclip the upper door sill lining (5) .


Remove the plate mounting bolt.

Unclip the light.


Remove the three trim mounting bolts (6) .

Partially remove:

- the tailgate seal,

- the rear door seal.

Pull off the lower section of the wheel arch trim.


Pull out the seat belt web via the aperture (8) .

104363

104363

5

5

6 6

104362

Note:

There is no need to remove the boot carpet, orfully remove the wheel arch interior trim.

104361

7 7

8



SAFETY ACCESSORIES

Rear seat belt 59A

Remove:

- the seat belt anchorage bolt,

- the inertia reel bolt.


Remove the inertia reel.

Remove:

- the rear quarter panel trim,

- the wheel arch trim ( (see 71A, Body interior trim)).

Remove:

- the seat belt anchorage bolt (9) ,

- the inertia reel bolt (10) ,

- the « seat belt » assembly.

Remove:

- the bolt (11) ,

- the side stalk.

104346

104358

LONG CHASSIS

107103

107101

9

10

11



SAFETY ACCESSORIES

Rear seat belt 59A

Remove:

- the bolt (12) ,

- the centre stalks.

REFITTING

Torque tighten:

-the seat belt mounting bolts (21 Nm) ,

-the side stalk bolts (21 Nm) ,

-the centre stalk bolts (44 Nm) .


107114

Note:

For the long version rear centre seat belt method( (see 59A, Safety accessories) ).

12



SAFETY ACCESSORIES

Centre rear seat belt: Removal - Refitting 59A

REMOVAL


Remove:

- the seat belt buckle trim,

- the headlining ( (see 71A, Body interior trim) ).

Remove:

- the seat belt anchorage bolt,

- the inertia reel mounting bolt.

REFITTING

Torque tighten the seat belt mounting bolts (21Nm) .


Tightening torquesm


IMPORTANT

In case of doubt on how a safety system compo-nent is activated ( (see 03B, Impact) ).

104348

1

104344

Documents

Manual service Renault Scenic 2