3
PRODUCT SPECIFICATION Manufacturer: Big Foot Systems Product Name: Standard Frames Product Summary Light duty frame suitable for supporng mini splits, VRF/VRV condensers and small AHUs; Product Descripon Big Foot Systems standard frames are constructed from 40x40 box secon, stocked in 1m to 4m lengths, and available in 1.2m or 1.5m wide frames. The modular frameworks come with 305mm or 450mm feet. Suitable for most installaon requirements where non-penetrave support is required. This range of frames are designed to suit a wide arrangement of units in combinaon, simple to assemble and developed to resist pping and sliding up to a wind loading of 100mph. Pallesed kit, comes complete with adjustable leg assemblies, supplied with clamp kits. Features & Benefits Non penetrave load management. Cost effecve, pre-fabricated support system. Versale modular frameworks. Rubber crumb foot mat for roof finish protecon. Quick to install, robust and secure. Product Reference Standard frame lengths available in 500mm (19 11/16inches) increments from a minimum frame length of 1.0m (39 3/8inches) to maximum of 4.0m (157 31/64inches) . All frames are available in width of 1.2m (47 1/4inches) and 1.5m (59 1/16inches), to suit side by sideor back to backmulple condensing unit arrangement. Standards Constructed to: BS8000-4: Workmanship on building sites. Code of pracce for waterproofing. BS6229: Code of pracce for flat roofs with connuously supported coverings. Building Regulaons (E & W) Part L: Conservaon of Fuel and Power. BS EN 1850-1: Determinaon of visible defects. BS EN 1107-1: Flexible sheets for waterproofing. Determinaon of dimensional stability. Material Specificaon: Hot dip galvanized carbon steel: BS EN 10219-1. Welding standard: BS EN ISO 15614-1. Galvanizing: BS EN ISO 1461. Plasc foot: Nylon 6 B601L 30% glass fibre filled Rubber crumb foot mat: SBR recycled rubber BS 7188 and BS 5696-3 Salt mist tesng: BS EN 60068-2-52. Test Kb severity 1. Design Consideraons Foot Pressure & UDL (Roof Load): Allowable foot pressure and roof load will be subject to roof build-up, typically detailed by a structural engineer. Big Foot Systems work to a maximum foot pressure and UDL of 20kN/m2 and 7.5kN/m2 respecvely. Linear Adjustment: Cross bar spacing is adjustable to accommodate various unit sizes. Wind Loading: Suitable for wind exposed environments, up to wind speeds of 100mph. Height Adjustability: To suit several height requirements, there 3 variaons in height available. Standard—adjustable between 295-400mm (11 39/64-15 3/4); Long Stud—adjustable between 295-620mm (11 39/64-24 13/32); Long Box— between 725-830mm (28 35/64-32 43/64). Roof Surface: Suitable for any roof surface including but not limited to PVC membrane, masc asphalt, insulaon and concrete roof finishes. Working Condions: Suitable for internal or external applicaons in temperatures between -40 o C to +80 o C. Marine Environment: Salt mist test conducted in accordance with ASTM B117-11 to simulate an accelerated environmental test. The results validate the 10 year product guarantee issued by Big Foot Systems. Where to buy: Available to buy off the shelf from any partner wholesalers across the country. The link below provides the locaon of every wholesalers in the UK. www.bigfootsupport.com/distributors Opons Foot Fleeces: Recommended for use on PVC membrane and asphalt roof surfaces to prevent migraon of plascizers. B9156—305mm (12 1/64inches); B9157—450mm (17 23/32inches) Angled Mats: 2.5 and 5 degrees angled mats available for 305mm and 450mm feet only, for use on roof fall up to 6 degrees. B9091—2.5 o 305; B9092—5.0 o 305; B9093—2.5 o 450; B9094—5.0 o 450 feet.

Manufacturer: ig Foot Systems Standard frame lengths ...Welding standard: S EN ISO 15614-1. Galvanizing: S EN ISO 1461. Plastic foot: Nylon 6 601L 30% glass fibre filled Rubber crumb

  • Upload
    others

  • View
    14

  • Download
    0

Embed Size (px)

Citation preview

PRODUCT SPECIFICATION

Manufacturer: Big Foot Systems

Product Name: Standard Frames

Product Summary

Light duty frame suitable for supporting mini splits, VRF/VRV condensers and small AHUs;

Product Description

Big Foot Systems standard frames are constructed from 40x40 box section, stocked in 1m to

4m lengths, and available in 1.2m or 1.5m wide frames. The modular frameworks come with

305mm or 450mm feet. Suitable for most installation requirements where non-penetrative

support is required.

This range of frames are designed to suit a wide arrangement of units in combination, simple

to assemble and developed to resist tipping and sliding up to a wind loading of 100mph.

Palletised kit, comes complete with adjustable leg assemblies, supplied with clamp kits.

Features & Benefits

Non penetrative load management.

Cost effective, pre-fabricated support system.

Versatile modular frameworks.

Rubber crumb foot mat for roof finish protection.

Quick to install, robust and secure.

Product Reference

Standard frame lengths available in 500mm (19 11/16inches) increments from a minimum frame length of 1.0m (39 3/8inches) to maximum of 4.0m (157 31/64inches) . All frames are available in width of 1.2m (47 1/4inches) and 1.5m (59 1/16inches), to suit ‘side by side’ or ‘back to back’ multiple condensing unit arrangement.

Standards

Constructed to:

BS8000-4: Workmanship on building sites. Code of practice for waterproofing.

BS6229: Code of practice for flat roofs with continuously supported coverings.

Building Regulations (E & W) Part L: Conservation of Fuel and Power.

BS EN 1850-1: Determination of visible defects.

BS EN 1107-1: Flexible sheets for waterproofing. Determination of dimensional stability.

Material Specification:

Hot dip galvanized carbon steel: BS EN 10219-1. Welding standard: BS EN ISO 15614-1.

Galvanizing: BS EN ISO 1461.

Plastic foot: Nylon 6 B601L 30% glass fibre filled

Rubber crumb foot mat: SBR recycled rubber BS 7188 and BS 5696-3

Salt mist testing: BS EN 60068-2-52.

Test Kb severity 1.

Design Considerations

Foot Pressure & UDL (Roof Load):

Allowable foot pressure and roof load will be subject to roof build-up, typically detailed by a structural

engineer. Big Foot Systems work to a maximum foot pressure and UDL of 20kN/m2 and 7.5kN/m2

respectively.

Linear Adjustment:

Cross bar spacing is adjustable to accommodate various unit sizes.

Wind Loading:

Suitable for wind exposed environments, up to wind speeds of 100mph.

Height Adjustability:

To suit several height requirements, there 3 variations in height available. Standard—adjustable between

295-400mm (11 39/64-15 3/4); Long Stud—adjustable between 295-620mm (11 39/64-24 13/32); Long

Box— between 725-830mm (28 35/64-32 43/64).

Roof Surface:

Suitable for any roof surface including but not limited to PVC membrane, mastic asphalt,

insulation and concrete roof finishes.

Working Conditions:

Suitable for internal or external applications in temperatures between -40oC to +80oC.

Marine Environment:

Salt mist test conducted in accordance with ASTM B117-11 to simulate an accelerated environmental

test. The results validate the 10 year product guarantee issued by Big Foot Systems.

Where to buy:

Available to buy off the shelf from any partner wholesalers across the country. The link below

provides the location of every wholesalers in the UK. www.bigfootsupport.com/distributors

Options

Foot Fleeces:

Recommended for use on PVC membrane and asphalt roof surfaces to prevent migration of plasticizers.

B9156—305mm (12 1/64inches); B9157—450mm (17 23/32inches)

Angled Mats:

2.5 and 5 degrees angled mats available for 305mm and 450mm feet only, for use on roof fall up to 6

degrees. B9091—2.5o 305; B9092—5.0o 305; B9093—2.5o 450; B9094—5.0o 450 feet.

TITLE:

Standard Frames Product

Specification Sheet

DWG No.

BFT-STF.dwg—Page 1

THIS DRAWING IS COPYRIGHT AND

THE PROPERTY OF BIG FOOT SYSTEMS LIMITED

Installation and application considerations should

include health, safety and environmental needs,

regulations and standards, codes of practice,

climate conditions,

installation location, product orientation, evalua-

tion of the roof structure, composition, surface and

condition, ancillary and complimentary products

and materials. Big Foot Systems recommend that

all rooftop products are handled and installed by

suitably qualified persons. All scheme designs are

based on the use of Big Foot Systems' products

and materials only.

Terms and conditions available on request

Frame - 1.0m x 1.2m (LxW) B6075 B9088 B9569 B6702 B9384 B9572

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Frame - 1.5m x 1.2m (LxW) B9449 B9587 B9549 B9601 B9588 B9550

Frame - 2.0m x 1.2m (LxW) B6077 B9089 B9570 B6703 B9385 B9573

Frame - 3.0m x 1.2m (LxW) B6078 B9090 B9571 B6704 B9386 B9574

Frame - 4.0m x 1.2m (LxW) B0105 B0106 B0107 B0108 B0109 B0110

Frame - 2.5m x 1.2m (LxW) B9451 B9593 B9555 B9603 B9607 B9556

Frame - 3.5m x 1.2m (LxW) B9453 B9598 B9561 B9605 B9599 B9562

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12 12 12 12 12 12

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

TITLE:

Standard Frames Product

Specification Sheet

DWG No.

BFT-STF.dwg—Page 2

THIS DRAWING IS COPYRIGHT AND

THE PROPERTY OF BIG FOOT SYSTEMS LIMITED

Installation and application considerations should

include health, safety and environmental needs,

regulations and standards, codes of practice,

climate conditions,

installation location, product orientation, evalua-

tion of the roof structure, composition, surface and

condition, ancillary and complimentary products

and materials. Big Foot Systems recommend that

all rooftop products are handled and installed by

suitably qualified persons. All scheme designs are

based on the use of Big Foot Systems' products

and materials only.

Terms and conditions available on request

Frame - 1.0m x 1.5m (LxW) B9442 B9585 B9547 B9445 B9586 B9548

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Frame - 1.5m x 1.5m (LxW) B9450 B9589 B9551 B9602 B9590 B9552

Frame - 2.0m x 1.5m (LxW) B9443 B9591 B9553 B9446 B9592 B9554

Frame - 3.0m x 1.5m (LxW) B9444 B9596 B9559 B9447 B9597 B9560

Frame - 4.0m x 1.5m (LxW) B0111 B0112 B0113 B0114 B0115 B0116

Frame - 2.5m x 1.5m (LxW) B9452 B9594 B9557 B9604 B9595 B9558

Frame - 3.5m x 1.5m (LxW) B9454 B9600 B9563 B9606 B9608 B9564

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24 32 15 24 32

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64

Height

Min

mm 295 295 725 295 295 725

Inches 11

39/64 11

39/64 28

35/64 11

39/64 11

39/64 28

35/64

Max mm 400 620 830 400 620 830

Inches 15 3/4 24

13/32 32

43/64 15 3/4

24 13/32

32 43/64

Foot Size mm 305 305 305 450 450 450

Inches 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64 12

1/64