Upload
hoangtu
View
247
Download
2
Embed Size (px)
Citation preview
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-1
P-51
SOLIDWORKS 15 to Mastercam X82015
A. Open SW File in Mastercam X8.Step 1. If necessary, save your Fuselage file in SOLIDWORKS.
Step 2. In Mastercam X8, click FILE Menu > Open.
Step 3. In the Open dialog box set Files of type toSOLIDWORKS Files, select your FUSELAGE fileand click Open, Fig. 1.
Step 4. Change to Isometric View (Alt-7).
B. Confirm Units are Inches.
Step 1. Confirm in the bottom right corner of the display units are Inches, Fig. 2.
C. Save Your File.Step 1. Click FILE Menu > Save As.
Step 2. Key-in FUSELAGE for the filename and press ENTER.
Chapter 3
4/30/15
Chapter 3Mastercam X8Chapter 15
Fig. 1
Fig. 2
© Cudacountry.net Tech Edhttp://www.cudacountry.net email:[email protected]
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-2
D. Rotate Fuselage Around Axes.Step 1. Click down arrow of Set Planes in toolbar
and click Top (WCS), Fig 3.
Step 2. Click XFORM Menu > Rotate.
Step 3. Click the solid body to select it, Fig 4. Click End Se-lection (ENTER) in ribbon bar.
Step 4. In Rotate dialog box set: Move Fig. 5 Number of Steps 1
Rotation Angle -90 Click Apply .
Step 5. Click down arrow of Set Planes in toolbar and click Front (WCS), Fig 6.
Step 6. Click the solid body again to select it and click End Selection (ENTER) in ribbon bar, Fig. 7.
Step 7. Set: Move Fig. 8
Rotation Angle 90 Click OK .
Step 8. Fit (Alt-F1),
Step 9. Right click graphics area and click Clear Colors (Alt-R C).
Step 10. Delete surface imported from SOLIDWORKS, Fig. 9. To delete, click to select and press Delete key.
Step 11. Save (Alt-F S).
Fig. 3
Fig. 8
Fig. 5
Fig. 6
Fig. 4
Solid body
Fig. 7
Solid body
Fig. 9
Delete surface
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-3
E. Move Origin.Step 1. Click the down arrow of the Set Planes button
in the toolbar and click Top (WCS), Fig 10.
Step 2. Display the Origin. Use F9 to show the axes, Fig. 11.
Step 3. Click Xform Menu > Translate.
Step 4. Click Fuselage, Fig. 11.
Step 5. Click End Selection (ENTER) in ribbon bar.
Step 6. In Translate dialog box set: Select Move Fig. 12 Z -1.25 Click OK .
Step 7. Right click the drawing area and click Clear Colors from the menu or use Alt-R C.
Step 8. The Origin is now directly 1.25 above the motor hole at top edge of stock, Fig. 13.
Fig. 11
Fig. 12
Fig. 13
SOLIDWORKS Origin
New Mastercam Origin
Fig. 10
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-4
F. Create Containment.Step 1. Click CREATE Menu > Rectangular Shapes.
Step 2. In Rectangular Shapes Options set:
Base Point Fig. 14
Width 8.7
Height 1.7 Click left center Anchor point
Click down arrow in Auto Cursor ribbon bar and click Origin to place rectangle, Fig. 15 and Fig. 16.
Click OK .
Step 3. Save . Use Alt-F S.
Fig. 14Fig. 15
Fig. 16
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-5
G. Create WCS BOTTOM CUT.Step 1. Click VIEW Menu > Orient > Flip Y
for Z, Fig. 17.
Step 2. Fit (Alt-F1).
Step 3. Click WCS in the Status Bar at the bot-tom of the graphics area and Plane Man-ager from the menu, Fig. 18.
Step 4. Click Geometry button in the Plane Manager dialog, Fig. 19.
Step 5. Click Line 1 and Line 2 for construction plane geometry, Fig. 20.
Step 6. In the Select plane dialog box, Fig. 21, set X axes to point to the rear and Y axes to point right, Fig. 22. This should be View 6 of 8, Fig. 21. Click OK in the Select plane dialog box.
Fig. 18
Fig. 19
Fig. 21
Line 2
Fig. 17
Fig. 20
Line 1
Fig. 22
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-6
Step 7. Key-in BOTTOM CUT for name in the New Plane dialog and click OK , Fig. 23.
Step 8. Back in the Plane Manager set, Fig. 24 Origin X 0 Origin Y 0 Origin Z 2.5
Step 9. Click Set All button
, Fig. 24 andFig. 25.
Step 10. Click OK .
Step 11. Confirm the BOTTOM CUT origin, Fig. 26.
Step 12. Save . Use Alt-F S.
Fig. 23
Fig. 24
Fig. 25
Fig. 26
BOTTOM CUT Origin
Mastercam X8 P-51 Fuselage SW 15 to MCX8 HST Page 15-7
H. Switch Back to Top WCS.Step 1. Click WCS in the Status Bar at the bottom of the graphics area and Plane Manager from
the menu, Fig. 27.
Step 2. Click TOP in the Plane Manager dialog, Fig. 28.
Step 3. Click Set All button
, Fig. 28.
Step 4. Click OK ,Fig. 28.
Step 5. Change to Isometric View (Alt-7).
Step 6. Save . Use Alt-F S.
Fig. 29
Fig. 27
Fig. 28TOP
Origin