Material Training UB-Yokogawa

Universal Temperature Controller

Advanced ControlSimplicityNetworkingReliability

Copyright© 2009 Yokogawa Electric Corporation All Right ReservedJanuary 23rd, 2009

Training Pra Lomba PLC NasionalUB-Yokogawa Indonesia

Panitia E-PLC 2012


Full

Con

trol

at

Your

Fin

gert

ips


2

Topik

۞ Pengenalan UT Advanced۞ Fitur Software UT Advaced۞ Pemrograman Ladder ۞ Monitoring

Digunakan untuk Lomba PLC UBSeijin Yokogawa Indonesia


Full

Con

trol

at

Your

Fin

gert

ips


3

۞ Install PC software LL50A– (setup dan USB Driver)

Install software

USBUSB



Full

Con

trol

at

Your

Fin

gert

ips


General System - UT35A Controller


4

X_DI1X_DI2 Y_AL1

Y_AL2

Y_AL3F1_KeyF2_KeyFn_Key

M01-M99

DAT01-DAT20

(256 Marker)

(28 Data Register)

P01-P10(10 P-Parameter)

input output

Controller


Full

Con

trol

at

Your

Fin

gert

ips


Fitur-Fitur

۞ Timer (4 buah)۞ Counter (4 buah)۞ Aritmatika (add, E_add, sub, E_sub, mul, div, …)۞ Logika (and, or, xor, not, dll)۞ Transfer Data (mov, E_mov)۞ Pemrosesan Data (Bin, LLM, Min, Max, dll)۞ CLK (CLK1, CLK2, CLK10, CLK60)۞ PLS1 (always ON)۞ Input Diferensial (DIFU, DIFD)

5Digunakan untuk Lomba PLC UBSeijin Yokogawa Indonesia


Full

Con

trol

at

Your

Fin

gert

ips


Basic Instruction (#1)

6


Full

Con

trol

at

Your

Fin

gert

ips


Basic Instruction (#2)



Full

Con

trol

at

Your

Fin

gert

ips


Operasi Aritmatika



Full

Con

trol

at

Your

Fin

gert

ips


Comparison



Full

Con

trol

at

Your

Fin

gert

ips


Komputasi logika

10


Full

Con

trol

at

Your

Fin

gert

ips


11

Start LL50A

۞ Start LL50A – Start up LL50A and click “OK”



Full

Con

trol

at

Your

Fin

gert

ips


12

۞ Create new file– Select Use for “LADDER SEQUENCE FUNCTION” and click “OK”

Ladder Program



Full

Con

trol

at

Your

Fin

gert

ips


13

۞ One line ladder program– Select [Build Ladder Program] folder



Full

Con

trol

at

Your

Fin

gert

ips


UTAdvanced Pre-Release InformationInternal Use Only

14

۞ Click “Yes (Y)” and input program name

Ladder Program

Input name as “UTAdv”


Full

Con

trol

at

Your

Fin

gert

ips



15

۞ One line ladder program– Select [User ladder calculation] tab (a)– Select and put “X_DI1”. Select and put “Y_AL1”

Ladder Program

(a)


Full

Con

trol

at

Your

Fin

gert

ips


16

۞ Download ladder program to UTAdvanced– Select [Communication] [Download Ladder Program Data] in menu– Save the setting

Ladder Program



Full

Con

trol

at

Your

Fin

gert

ips


17

۞ Download ladder program to UTAdvanced– Select Communication port

1. For USB dedicated cable connection: Select serial port no.2. For Ethernet cable connection: Input “192.168.1.10”

– Click [Download Ladder Program Data] – After download complete, select [Windows] [Close all]

Ladder Program



Full

Con

trol

at

Your

Fin

gert

ips


18

۞ Download ladder program to UTAdvanced– Click [Download Ladder Program Data]

– After download complete, select [Windows] [Close all]

Ladder Program



Full

Con

trol

at

Your

Fin

gert

ips



19

۞ Monitoring ladder programming– Select [Communication] [Monitor Ladder program] in menu– Select [Monitor Ladder Program]

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



20

۞ Monitoring – Set simulator DI01 switch ON then monitor program

Set DI01 ON and check LED ON

Ladder Program

Simulator Be sure to turn LED SW ON, which is on the side of simulator

LED SW


Full

Con

trol

at

Your

Fin

gert

ips



21

۞ Two lines ladder program– Open the One line ladder program setting (a)– Modify “one line ladder program” – Line 003: draw line, put and input “CLK1, TIM1, K01”– Line 004: Put as “TIM1”, put as “Y_AL2”

TIM

1 sec timer, timer#1, time out=K01

Ladder Program

Timer#1 time up?

(a)


Full

Con

trol

at

Your

Fin

gert

ips



22

Ladder Program۞ Download ladder program to UTAdvanced

– Select [Communication] [Download Ladder Program Data] in menu– Click [Download Ladder Program Data]

– After download complete, select [Windows] [Close all]


Full

Con

trol

at

Your

Fin

gert

ips



23

۞ Monitoring ladder programming– Select [Communication] [Monitor Ladder program] in menu– Select [Monitor Ladder Program]

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



24

۞ Monitoring– Set simulator DI01 switch ON then monitor program

Make sure D2 lamp ON after 5 sec

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



25

۞ Open Ladder program setting: Application– Select [File] [Open] in menu– Select the file “UTA_ladder_appli1.uta” from the USB memory

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



26

۞ Download Ladder program to UTAdvanced– Select [Communication] [Download All] in the menu– Click [Download Ladder Program Data]– After download complete, select [Windows] [Close all]– Monitor program

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



27

۞ Operation – When simulator’s DI01 is ON, control starts– When PV is over “K02” value(30), Timer will start (LED ON)– After 5 sec (Timer 1), the control stops (LED OFF)

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



28

۞ Operation – Set simulator’s DI01 ON to start – Change SP to more than 30

Check UTAdvanced STOP (LED ON)

Ladder Program


Full

Con

trol

at

Your

Fin

gert

ips



29

۞ Detail view monitoring – Select [Monitor] [Detail view] in menu to see the detail value

If PV>SP (30) then Timer#1 starts

Ladder Program

Documents

Material Training UB-Yokogawa