Mechanical Department trade-wise Multiple Choice Question- Jagadhri Workshop.

C&W trade Objective Question Bank

Fill in the blanks picking up the appropriate option: 1. Riding Index of ICF Coach is ----------- (a) 3.5 (b) 4.78 (c) 5.8 (d) 2.2 2. Maximum Speed of LHB Coach is ------------- KMPH. (a) 120 (b) 160 (c) 110 (d) 130 3. …………. roller bearing is used in BOXN/BCN. (a) Cylindrical (b) Plan (c) Cartage taper (d) Ball 4. POH of BOX N Wagon is done at the interval of……………month. (a) 12 (b) 09 (c) 18 (d) 54 5. POH of ICF Coach is done at the interval of……..month. (a) 24 (b) 12 (c) 18 (d) 30 6. Maximum Flange thickness of worn wheel profile is ………..mm. (a) 22 (b) 16 (c) 29.4 (d) 28.5 7. Roof sheet thickness in BCNA wagon is………..mm. (a) 2.4 (b) 0.6 (c) 1.6 (d) 2.5 8. Wheel base of casnub bogie is………….mm. (a) 2000 (b) 2400 (c) 1200 (d) 900 9. Testing of alarm chain is done at…….. Kg weight. (a) 05 (b) 10 (c) 25 (d) 20 10. DCP Type fire extinguisher is suitable to extinguish……… (a) Diesel (b) Electric (c) Petrol (d) All 11. There are……….. Nos. of lavatory in a LHB coach. (a) 02 (b) 03 (c) 04 (d) 06 12. Minimum buffer height of goods wagon is……..mm. (a) 1030 (b) 1075 (c) 1105 (d) 995 13. Minimum Wheel dia of Casnub Bogie is……..mm. (a) 1000 (b) 906 (c) 1092 (d) 950

14. Condemn height of Elastomeric Pad is…………. (a) 40 (b) 42 (c) 46 (d) None 15. ……………….. bearing is used in UIC Bogie. (a) Cylindrical (b) Spherical (c) CTRB (d) None of these 16. Permissible variation in Wheel dia of same casnub bogies of a wagon is…..mm. (a) 5 (b) 10 (c) 13 (d) 25 17. Permissible limit of sharp flange of wheel is…………mm. (a) 35 (b) 50 (c) 16 (d) None of these 18. …………….. mm packing is used in Casnub Bogie to adjust CBC height. (a) 37 (b) 25 (c) 35 (d) None of these 19. A dimension of BOXN is……….mm. (a) 70 ± 2 (b) 70+2-0 (c) 50 ± 2 (d)22 ± 2 20. BOXNHL feed pipe pressure is………. Kg/Cm2

(a) 5 (b) 6 (c) 3.8 (d) None of these 21. Axle is checked by……………. (a) DPT (b) UST (c) Wheel gauge (d) None of these 22. Centre pivot of Casnub Bogie is made of………….. (a) Cast Iron (b) Cast steel (c) Mild Steel (d) Stainless Steel 23. Proof load Capacity of enhance screw coupling is………….ton. (a) 36 (b) 70 (c) 75 (d) 130 24. In one unit of BLC wagon there are……….. car A unit. (a) 3 (b) 5 (c) 2 (d) 4 25. Maximum buffer height of goods wagon is………..mm. (a) 1030 (b) 1075 (c) 1105 (d) 995 26. Free height of CC Pad is…………… (a) 114 (b) 36 (c) 56 (d) None of these 27. …………………. bearing is used in casnub bogie. (a) Cylindrical (b) Spherical (c) CTRB (d) None of these 28. Permissible Wheel dia difference of both casnub bogies of a wagon is……..mm. (a) 5 (b) 10 (c) 13 (d) 25 29. Permissible limit of Deep flange in wheel is……..mm. (a) 35 (b) 50 (c) 28 (d) 22

30. 37 MM packing is used in 22 WM casnub bogie to adjust CBC height wheel dia ……mm. (a) 924 (b) 900 (c) 905 (d) 950 31. Brake pipe pressure is……………. Kg/Cm2

(a) 5 (b) 6 (c) 3.8 (d) 4 32. ………………. is checked with tyre defect gauge. (a) wheel defect (b) Buckle defect (c) CBC defect (d) door defect 33. Wheel gauge (distance between two wheels) is…………. (a) 1600±2 (b) 1600+2-1 (c) 1599 (d) 1676±3 34. Riding index of LHB coach is………….. (a) 2.75 (b) 2.0 (c) 4.8 (d) None of these 35. Friction cofficient of K type composite brake block is…………. (a) 1.4 (b) 2.8 (c) 1.6 (d) 0.25 36. In one unit of BLC wagon there are………car B unit. (a) 3 (b) 5 (c) 2 (d) 4 37. ……………….. gms Grease is used in CTRB. (a) 455±30 (b) 250±30 (c) NIL (d) 1500 38. IOH of ICF Coach is done in the interval of………month. (a) 12 (b) 9 (c) 18 (d) 54 39. Limit of flat tyre in wagon is………mm (a) 20 (b) 50 (c) 75 (d) 60 40. Axle Load of AC coach is………..Ton. (a) 16.3 (b) 13.3 (c) 20.3 (d) 18.3

GENERAL 1. The standard wheel gauge of passenger BG coaching stock is----- (a) 1602 mm (b) 1601 mm (c) 1600 mm (d) 1598 mm 2. The maximum wheel gauge of passenger BG coaching stock is ---- (a) 1600 mm (b) 1601 mm (c) 1598.5mm (d) 1602 mm

3. The minimum permissible wheel gauge of passenger BG coaching stock is – (a) 1601.5 mm (b) 1600 mm (c) 1599 mm (d) 1601 mm

4. Length over body of ICF BG coaches is----- (a) 2334 mm (b) 2310 mm (c) 21337 mm (d) 22132 mm 5. Rigid wheelbase of ICF BG trolley is – (a) 2896 mm (b) 2803 mm (c) 2990 mm (d) 2837 mm

6. What is the period for the POH of any OCV attached to a passenger train? (a) Nine month (b) 12 month (c) 18 month (d) 24 month 7. What shall be the period for POH for a coach attached to Mail/ Express train? (a) 9 month (b) 12 month (c) 18 month (d) 24 month 8. The other name of pilot valve is – (a) PESAD (b) PEASD (c) PDEAS (d) EPASD 9. What is the Transportation code of second class fitted with self-generating electrical equipment? (a) SG (b) GS (c) GY (d) GSD 10. What is the Transportation code of inspection carriage (Administrative)? (a) AR (b) CR(c) IC (d) RA 11. Transportation codes of the pantry car is – (a) BC (b) PC (c) WCB (d) CD 12. Which part is not used in ICF trolley? (a) Dashpot (b) Side bearer (c) Shock absorber (d) Drag link 13. Transportation codes of vestibule second class 3- tier sleeper coach fitted with self-generating electrical equipment is------ (a) WGSCNA (b) WGSCN (c) MGSCN (d) GSMGCN 14. What is the Transportation code of vestibule three-tier sleeper coach fitted with self-generating electrical equipment and ladies compartment? (a) WCBSCZA (b) WGSCNY (c) WGSCWY (d) YZZFS 15. In coach, the load transmission takes place through--- (a) Center pivot (b) Bogie (c) Side bearer (d) Wheel 16. The ‘L’ type composite brake block should be changed, if worn out beyond- (a) 10 mm (b) 15 mm (c) 20 mm (d) 22 mm 17. The ‘K’ type composite brake block should be changed, if worn out beyond- (a) 10 mm (b) 12 mm (c) 20 mm (d) 22 mm 18. Std. packing pieces of ICF coach is – (a) 13,14,26 mm (b) 13,22,28 mm (c) 13,26,38,48 mm (d) 22,26,32 mm 19. Coaching stock accident involving human life enquiry by- (a) CME (b) CRS (c) Sr.DME (d) ADRM 20. Yellow strips on end body of ICF indicate is – (a) Antitclescopic (b) Dual brake (c) In built air brake (d) Non-Antitalescop 21. What defect is detecting UST test? (a) Internal crack (b) external crack (c) Air flow crack (d) None of the above

22. What is Codal life of steel bodied coaches (Including dining / pantry cars) – (a) 40 years (b) 30 years (c) 25 years (d) 22 years 23. Codal life of light utilisation categories of coaches is – (a) 40 years (b) 30 years (c) 25 years (d) 20 years 24. Periodicity of periodic overhauls of ICF coaches — (a) 12 Month (b) 18 Month (c) 24 Month(d) 30 Month 25. The standard thickness of compensating rings is – (a) 2 mm (b) 4 mm (c) 6 mm (d) 8 mm 26. Tare weight of the WGS CZAC coach is – (a) 50.30t (b) 49.30t (c) 48.77 t (d) 47.22 t 27. Payload of the WGSCZAC coach is – (a) 6.38t (b) 7.22 t (c) 5.680 t (d) 4.889 t 28. Gross weight of the WGSCZAC coach is----------- (a) 54.98 t (b) 56.36 t (c) 59.22 t (d) 52.23t 29. Tare weight of the WGSCWAC coach is------------------ (a) 49.75 t (b) 49.30 t (c) 50.00 t (d) 46.50 t 30. Total payload of the WGSCWAC coach is---------------- (a) 1.440 t b) 5.680 t (c) 3.680 t (d) 37.70 t 31. Tare weight of the GS coach is – (a) 36.99 t b) 46.99 t (c) 38.03 t (c) 38.03 t 32. Normal payload of the GS coach is ------------ (a) 6.98 t (b) 5.85 t (c) 6..67 t (d) 7.21 t 33. Total payload of the GS coach is – (a) 5.79 t (b) 12.60 t (c) 11.70 t (d) 14.04 t CBC/ DRAFT GEAR 1. The maximum standard buffer height above rail level to center of buffer is – (a) 1085 mm (b) 1100 mm (c) 1105 mm (d) 1030 mm 2. The minimum permissible buffer height above rail level to center of buffer is – (a) 1105 mm (b) 1145 mm (c) 1115 mm (d) 1030 mm 3. Standard buffer projection from Headstock is – (a) 650 mm (b) 635 mm (c) 620 mm (d) 660 mm

4. Minimum Permissible buffer projection from Headstock is--- (a) 635 mm (b) 605 mm (c) 590 mm (d) 584 mm 5. The diameter of buffer plunger face of ICF coaches is--- (a) 552 mm (b) 457 mm (c) 493 mm (d) 510 mm 6. In ICF coach drawbar and Headstock, what should be the maximum buffer projection in mm? (a) 92.0 mm (b) 34.0 mm (c) 36.0 mm (d) 38.0 mm 7. What is the distance between two buffers at one end? (a) 1952 mm (b) 1976 mm (c) 1956 mm (d) 1992 mm 8. What is the maximum buffer plunger stroke in mm? (a) 127.0 mm (b) 129.0 mm (c) 131.0 mm (d) 133.0 mm 9. How the weight of the body is transferred on trolley in ICF coach? (a) Journal (b) Wheel (c) Side bearer (d) Dashpot 10. What should be the minimum buffer height after POH? (a) 1050 mm (b) 1060 mm (c) 1080 mm (d) 1090 mm 11. The ICF buffer plunger is made of – (a) Mild steel (b) Cost iron (c) Cast steel (d) Aluminum Alloy 12. In loaded condition, the minimum permissible height of buffer in ICF coach is— (a) 1090 mm (b) 1105 mm (c) 1030 mm (d) None of the above 13. What is the buffer stroke in ICF coach? (a) 127.0 mm (b) 129.0 mm (c) 131.0 mm (d) 133.0 mm 14. The new thickness of a draft pad in ICF coach is – (a) 30.0 mm (b) 32.0 mm (c) 33.0 mm (d) 34.0 mm 15. The condemning thickness of draft pad in ICF coaches? (a) 30.0 mm (b) 32.0 mm (c) 33.0 mm (d) 34.0 mm WHEEL & AXLE 1. Permissible variations in wheel tread diameter for four-wheeled trolley (IRS-Non IRS) on the same axle on BG is –(while turning the wheel) (a) 0.5 mm (b) 0.49 mm (c) 0.30 mm (d) 0.45 mm 2. Permissible variations in wheel tread diameter for four-wheeled trolley on the same coach on BG is –(while turning the wheel) (a) 12.0 mm (b) 10.0 mm (c) 11.0 mm (d) 13.0 mm 3. Permissible variations in wheel tread diameter for four-wheeled trolley (Sehileren, ICF, and BEML) in the same trolley on BG is -(while turning the wheel) (a) 10.0 mm (b) 7.0 mm (c) 5.0 mm (d) 8.0 mm

4. The use of 16.25 tons axle load bogie is in – (a) WGS (b) AC (c) WGSCN (d) Non AC 5. Axle load capacity of generator (WLLRM) coach is – (a) 16.0 tons (b) 22.9 tons (c) 15.0 tons (d) 20.30 tons 6. What is the size of direct mounted roller bearing journal of ICF bogie? (a) 125*111 mm (b) 120*113.5 mm (c) 125*130 mm (d) 130*100 mm 7. Flat Place on wheel of ICF coach is – (a) 60.0 mm (b) 50.0 mm (c) 75.0 mm (d) 90.0 mm 8. High speed ICF coach condemning flange thickness below – (a) 14.0 mm (b) 13.0 mm (c) 22.0 mm (d) 10.0 mm 9. Lateral movements of wheels are controlled by – (a) Axle Guide (b) Journal center (c) roller bearing (d) Desh pot 10. Maximum axle load bearing capacity of AC ICF/RCF coach is--- (a) 16.25 t b) 13 t (c) 15 t (d) 14.28 t 11. Bogie wheelbase of ICF/ RCF all coil bogies are— (a) 2896 mm (b) 2986 mm (c) 2886 mm (d) 2997 mm 12. What is the new wheel diameter of ICF/ RCF coach is--- (a) 910 mm (b) 915 mm (c) 930 mm (d) 925 mm 13. Min shop issue size of ICF solid wheel is – (a) 837 mm (b) 870 mm (c) 854 mm (d) 8746 mm 14. Flange thickness of new BG wheel coach is – (a) 28.0 mm (b) 28.50 mm (c) 29.40 mm (d) 27.50 mm 15. After POH, the lowest permissible wheel diameter for a coach is – (a) Not less then 900 mm (b) Not less then 860 mm (c) Not less then 837 mm (d) Not less then 826 mm . AIR BRAKE 1. Capacity of air reservoir (AR) of the coach is – (a) 150 Lit. (b) 200 Lit. (c) 250 Lit. (d) 300 Lit. 2. In twin pipe system, the time taken for releasing of the brake is – (a) 45 sec (b) 27 sec (c) 75 sec (d) 120 sec 3. In the passenger train, the diameter of brake pipe & feed pipe is – (a) 20.0 mm (b) 25.0 mm (c) 28.0 mm (d) 30.0 mm

4. In the passenger train, the diameter of branch pipe is – (a) 15.0 mm (b) 18.0 mm (c) 20.0 mm (d) 22.0 mm 5. What is the diameter of branch pipe attached to PEAV? (a) 15.0 mm (b) 25.0 mm (c) 30.0 mm (d) 20.0 mm 6. BP pressure in working train is – (a) 6.0± 0.1Kg/cm2 (b) 5.5± 0.1 Kg/cm2 (c) 5.0± 0.1 Kg/cm2 (d) 5.2± 0.1 Kg/cm2 7. During charging position, Air pressure in Auxiliary reservoir is – (a) 6.5 Kg/cm2 (b) 6.1 Kg/cm2 (c) 6.0 Kg/cm2 (d) None of the above 8. During full service application, Brake pipe pressure is dropped to – (a) 2.0 Kg/cm2 (b) 1.0 Kg/cm2 (c) 3.0 Kg/cm2 (d) 1.5 Kg/cm2 9. The full form of BP is – (a) By pass (b) Brake pipe (c) Bent pipe (d) None of the above 10. In twin pipe system, the AR pressure should be – (a) 5.0 Kg/cm2 (b) 6.0 Kg/cm2 (c) 7.0 Kg/cm2 (d) 8.0 Kg/cm2

UNDER GEAR /BOGIE 1. What is amount of the oil per side bearer in ICF coaches? (a) 1.2 letter (b) 1.6 letter (c) 2.5 letter (d) 2.2 letter 2. With what the lateral and longitudinal guides of ICF bogie is mounted? (a) Dash pot (b) side bearer (c) CBC (d) Spring 3. What should be the maximum distance between safety loop and axle in ICF bogie? (a) 32.0 mm (b) 35.0 mm (c) 40.0 mm (d) 44.0 mm 4. What is the distance between side bearers of ICF coach? (a) 1560 mm (b) 1590 mm (c) 1600 mm (d) 1610 mm 5. In released position, the gap between brake block and wheel is – (a) 3 mm (b) 4 mm (c) 5 mm (d) 7 mm 6. What is the oil level in dashpot? (a) 50.0 mm (b) 40.0 mm (c) 75.0 mm (d) 90.0 mm 7. In bogie mounted air brake systems, the No of brake cylinder are – (a) 8 (b) 6 (c) 2 (d) 4 8. In ICF & RCF bogie, the total height of primary spring and compensating ring should not exceed – (a) 285 mm (b) 290 mm (c) 295 mm (d) 300 mm

9. The crown clearance “A” between the axle box crown and the bogie frame of GS, SPC, SLR, SCN, VPH coaches is – (a) 40±2 mm (b) 43±0/3 mm (c) 42±0/4 mm (d) 45±2 mm 10. In WGACCW, WGACCN coaches, the crown clearance between the axle box crown and the bogie frame is – (a) 30±2 mm (b) 30± 5 mm(c) 27± 0/3 mm (d) 25± 0/3 mm LHB COACH 1. What is the berth capacity of AC-2- Tier LHB coach? (a) 54 berth (b) 72 berth (c) 46 berth (d) 64 berth 2. Berth capacity of AC-3-Tier LHB coach is – (a) 54 berth (b) 72 berth (c) 46 berth (d) 64 berth 3. Length over body of LHB coach is – (a) 21770 mm (b) 21337 mm (c) 23540 mm (d) 25540 mm 4. Maximum width of LHB coach is – (a) 3250 mm (b) 3240 mm (c) 3245 mm (d) 3325 mm 5. Height over roof of LHB coach is – (a) 4039 mm (b) 4025 mm (c) 4026 mm (d) 4047 mm 6. Rigid wheelbase of LHB coach is – (a) 2560 mm (b) 2896 mm (c) 2444 mm (d) 2440 mm 7. No of the toilet provided in LHB coach is – (a) Four (b) Two (c) Three (d) None of the above 8. Maximum CBC height drop under load and worn condition of LHB coach is – (a) 70 mm (b) 75 mm (c) 78 mm (d) 82 mm 9. Which bogies are provided for higher passengers ride index comfort? (a) ICF (all coil) (b) IRS type (c) BEML type (d) Fiat –SIG type 10. Maximum ride index of LHB coach is – (a) 2.75 (b) 3.25 (c) 3.65 (d) 3.45

C &M

Fill in the blanks with correct answer from the following 1. . ...........test is used to detect internal faults of the Axles. (a) Hardness (b) UST (c) DPT (d) None of them 2. . …………… is the unit of hardness. (a) BHN (b) Newton (c) Power (d) None of them

3. …………gas is used in MIG welding. (a) CO2 (b) DA (c) Oxygen (d) None of these 4. ------------change Mechanical Energy into Electrical Energy. (a) Motor (b) Generator (c) Pump (d) None of these 5. ------------ is increased in annealing process. (a) Hardness (b) Softness (c) Toughness (d) None 6. ------------ is increase by increasing of carbon percentage of steel. (a) Brittleness (b) Ductility (c) softness (d) None of these 7. The property to drawing the wire is called ………… (a) Ductality (b) Hardness (c) Stiffness (d) None 8. By tempering …………… increases. (a)Machinability (b) Hardness (c) Stiffness (d) None 9. Chisel is made from …………. (a) Cast Iron (b) Mild Steel (c) High Speed Steel (d) None 10. . …………. is done for normalizing in steel. (a) Fine Grain (b) Remove Stress (c) Ductility (d) None DISCIPLINE: WORKSHOP TECHNOLOGY Welding and Related Processes 1. Application of pressure and filler metal is essential in welding. a) True b) False 2. Plastic welding is also called……………welding. a) Pressure b) Fusion c) Non-pressure d) None 3. Fusion welding is also called………..welding. a) Pressure b) Fusion c) Non-pressure d) None 4. In cold welding………………….is applied. a) Heat b) Pressure c) Both d) None 5. Oxy-hydrogen process was used to weld…………melting point metals. a) Low b) High c) Both d) None 6. Anode is………………pole of DC power supply. a) Positive b) Negative c) Neutral d) None

7. Two thirds of heat is generated near………..pole. a) Negative b) Positive c) Neutral d) None 8. Electrode connected to positive pole will burn 50 percent faster than that is connected to negative pole. a) True b) False 9. Flux is used to prevent……………..of the surfaces to be soldered. a) Oxidation b) Rusting c) Melting d) None 10. Flux is used to dissolve …………. that settle on the metal surfaces during heating process. a) Oxides b) Rusts c) Carbides d) None 11. Brazing gives stronger joint than soldering. a) True b) False 12. One welding layer should be cooled before doing another layer. a) True b) False 13. Improper cleaning of surface causes…………… a) Improper penetration b) Under cutting c) Cracks d) None 14. High current and more Arc gap causes……………… a) Lack of Fusion b) Under cutting c) Cracks d) None 15. Atmospheric pressure on the barometer scale is- (a) 840mm (b) 760mm (c) 740mm (d) None of these 16. The air is compressed, its……….increases. (a) Pressure (b) Temperature (c) Both ‘a’ & ‘b’ (d) None Workshop Fill in the blanks with correct answer from the following. 1. ……….. Incentive scheme is in Jagadhri workshop. (a) CLW (b) RCF (c) DMW (d) None of them 2. …………gas is used in MIG welding. (a) CO2 (b) DA (c) Oxygen (d) None of them 3. Maximum Wheel Dia of BOXN is -------------mm (a) 1000 (b) 1090 (c) 840 (d) 740 4. Meaning of TQM is ………….. (a)Total Quality Management (b) Total Quantity Management (c) Total Quality Machine (d) None of them 5. EOT crane has ………. Motion. (a) 02 (b) 03 (c) 04 (d) 08

6. Meaning of PCO in workshop is…………. (a) Production Control Organisation (b) Police Control Office (c) Public call on (d) None of them. 7. ------------ is the highest authority of Mechanical Department in Zonal Railway. (a) CME (b) CFTM (c) COM (d) CPTM 8. M&P Programme prepared in the month of …… ……every year. a) December (b) June (c) August (d) April 9. ------------- hardness increased in case hardening. (a) External (b) Internal (c) Full (d) None of them. 10. DV is Overhauled in ................... (a) POH (b) ROH (c) NPOH (d) None of these 11. The work of limit switch is ....................... (a) Safety (b) Easy in operation (c) To stop Crane (d) None of these 12. AAC is for……………….Item. (a) Stock (b) Non stock (c) Imported Stock (d) Emergency Stock 13. …………………. type of defects can be detected in DPT test? (a) Surface (b) Internal (c) Hardness (d) None of them 14. …………. bearing is fitted in BLC wagon (a) CTRB (b) Cylindrical Roller (c) Spherical (d) None of them 15. Rail crane can be work…………….. (a) Only on Track (b) On road (c) On Both (d) None of them 16. Work of spark plug in Petrol Engine is…………… (a)Ignition (b) Compression (c) Power (d) None of these 17. Machine is used to manufacturing gear teeth…………. (a) Lathe (b) Milling (c) Grinding (d) Slotting 18. Final fit of wagon is given by………….. (a) SSE (b) SIO (c) NTXR (d) WM/R 19. Ignition is done in Diesel Engine by…………. a) Spark plug (b) Injector (c) Governor (d) None of these 20. RCF is located at…………… (a) Chennai (b) Kapurthala (c) Bangalore (d) None of these 21. In CLW pattern, JE gets……….. incentive percentage? (a) 100 (b) 50 (c) 80 (d) None of them

Budget & Store 1. No. of Demand in Budget pertaining to Railway (a)6 (b) 16 (c) 10 (d) 20 2. Repair & Maintenance of C&W is covered under which demand. (a)Demand No-1 (b) Demand No-16 (c) Demand No-6 (d) All of the above 3. Railway Board expenditure is covered under which demand. (a) Demand No-1 (b) Demand No-5 (c) Demand No-6 (d) Demand No-16 4. Operating expenditure of fuel for railway is covered under which grand (a) Demand No-10 (b) Demand No-8 (c) Demand No-9 (d) Demand No-5 5. Which No. is the Capital demand for Railway. (a)Demand No-1 (b)Demand No-16 (c) Demand No-2 (d) Demand No-5 6. Rolling stock programme is prepared to purchase. (a)Machinery & Plant (b) Carriage ,Wagon & Locomotive (c)To Purchase Building (d) All of the above 7. PL No. of stock item How many Numeric digits. (a)5 (b) 8 (c) 16 (d) 6 8. ABC analysis is related with- (a)To Regulate procurement of stock items (b)Repair of M&P (c)Repair of Building (d)All of the above 9. In Case of Rate contract---- (a)Quantity, Rate, Consignee are stripulated (b)On the Rate is Stripulated (c)Quantity, Rate is

Stripulated (d)Quantity, Rate & Delivery Period is Stripulated 10. Who is the Zonal Head of store department (a)CME (b) CMM (c) CRSE (d) CWE 11. Designation of Assistant Officer of store department of railway (a)ADME (b) AWM (c) AMM (d) AWEE 12. Which Standard form for used to issue stock items from store (a)S-1313 (b)S-1539 (c) S-1531 (d) None of these

13. Name of designation of JA/SAG officer of store department of railway. (a)DY CME (b) DY CMM (c) DY CEE (d) DY CE 14. No. of copies of Requisition are prepared---- (a)Two Copies (b) Three Copies (c) Six Copies (d) Four Copies 15. One aim of E-Procurement increasing saving by sourcing items: (a)From the right source (b) of the Right Quantity (c)At the Right Price (d) of The Right Quality

ABBREVIATIONS 1. AAC Annual Anticipated Consumption 2. AAR American Association Of Rail Road 3. AR Auxiliary Reservoir 4. BC Brake Cylinder 5. BP Brake Pipe. 6. BMBS Bogie Mounted Brake System 7. BMBC Bogie Mounted Brake Cylinder 8. CLW Chittranjan Locomotive Works 9. C & W Carriage and Wagon 10. CR Control Reservoir 11. CRS Commissioner of Railway Safety 12. CME Chief Mechanical Engineer 13. CRSE Chief Rolling Stock Engineer 14. CAMETCH Center For Advanced Maintenance Technology 15. CRB Chairman Railway Board 16. COFMOW Central Organization for Modernization Of Workshops. 17. CRIS Central for Railway Information System 18. CBC Center Buffer Coupler

19. CTRB Cartridge Tapered Roller Bearing 20. DGS&D Director General Of Supplies & Disposal 21. DRF Depreciation Reserve Fund 22. DV Distributor Valve 23. D&AR Discipline and Appeal Rules COMPUTER 1. Electronic & Mechanical parts from which computer is composed is called: (a) Software (b) Input (c) Hardware (d) Compuware 2. Series of instructions which command the computer to how to work is called:

(a) Software (b) Tupurware (c) Inverter (d) C.P.U. 3. Storage unit of Computer is known as: (a) Floppy Disc (b) Primary Storage (c) Hard Disc (d)

Secondary Storage 4. Full Form of C.P.U._______

(a) Central Processing Unit (b) Control Processing Unit (c) Control Programming Unit (d) None of these 5. What is Full form of WWW.

(a) World Wide Web (b) Wed Wide Web (c) World Web Wide (d) Wide World Web

6. 1 kilo bit___________ bits. (a) 1000 (b) 1024 (c) 512 (d) 256 7. To start & restart the computer is known as____________ (a) Exit (b) Text (c) Boot (d) Program 8. ________ Command is used to charge /correct the file which is already written. (a) Paste (b) Cut (c) Edit (d) Copy 9. Thousand of dots which make a picture on screen. (a) Pilem (b) Pixel (c) Pixment (d) Pint 10. Which is the input device in computer given below: (a) Mouse (b) Keyboard (c) Monitor (d) Speaker 11. Which is valid E-mail address given below: (a) rajiv_mahajan.com (b) rajiv@rediffmail.com (c) rajiv$rediffmail.com (d) rajiv_rediffmail.com 12. What Does HTTP stands for…..? (a) Head Tail Transfer Protocol (b) Hypertext Transfer Protocol (c) Hypertext Transfer Plotter (d)

Hypertext Transfer Plot 13. Full Form of URL is________?

(a) Uniform Resource Locator (b) Uniform Resource Link (c) Uniform Registered Link (d) Unifield Resource Link 14. Full Form of LAN is ___________ ? (a) Limited Area Network (b) Local Area Network (c) Limited Ample Network (d) Limited Access

Network 15. Which is most common language used in web designing? (a) C (b) C++ (c) PHP (d) HTML LHB 1. What is the full form of LHB? (a) Lower Heavy Bogie (b) Linke-Hofmann Busch (c) Low Height Bogie (d) None of these 2. How many brake disc on one wheel? (a) One (b) Two (c) Three (d) Four 3. What is the maximum Temperature limit for Timken CTBU?

(a) 90˚C (b) 80˚C (c) 85˚C (d) 87˚C

4. How many types of shock absorbers are used in LHB Coaches?

(a) 6 (b) 5 (c) 4 (d) 3 5.

How many shock absorbers are used in LHB coaches?

(a) 10 (b) 8 (c) 18 (d) 12

6. What is the name of shock absorbers connected between bogie and car body?

(a) Primary (b) Secondary (c) Yaw (d) None of these

7. Thickness of roof sheet of LHB coaches are:

(a) 2mm and 2.75mm (b) 1.25mm and 1.7mm (c) 3mm and 3.25mm (d) 2.75mm and 2.5mm

8. Thickness of side wall sheets of LHB coaches are:

(a) 2mm (b) 3mm (c) 1.25mm (d) 2.5mm

9. Yaw damper is fitted on:

(a) Sole bar (b) Bogie (c) under frame (d) Between under frame and bogie frame

BLC WAGON

1. In place of empty load box what device is used in BLC wagon?

(a) BSD (b) LSD (c) SDF (d) SAB

2. What is the material specification of BLC wagon trolley?

(a) Cast steel (b) Low Cast Steel (c) Steel (d) Micro Steel

3. The standard height of platform for BLC wagon from Rail level is _____

(a) 1010 mm (b) 1015mm (c) 1009mm (d) 1100mm

4. Axle load capacity of BLC wagon is ___]

(a) 20.10 ton (b) 20.32 ton (c) 21.10 ton (d) 23.10 ton

5. The tare weight of A car of BLC wagon is

(a) 21 .20 ton (b) 19.10 ton (c) 19.80 ton (d) 20.20ton

6. The tare weight of B car of BLC wagon is

(a) 18.10 ton (b) 19.10 ton (c) 19.80 ton (d) 20.22 ton

7. How many automatic twist locks used in BLC wagon

(a) 6 (b) 8 (c) 10 (d) 12

8. Rake carrying capacity of the BLC wagon is

(a) 40 wagons (b) 45 wagons (c) 46 wagons (d) 48 wagons

9. Which type of side bearer arrangement used in BLC trolley

(a) Elestromatic (b) Constant Contact Type(c) Spring loaded side bearer & PU pad (d) None of the

above

10. Which type of trolley used in BLC wagon

(a) VIC trolley (b) Cast steel bogie type lccf20cc (c) IRS trolley (d) diamond frame trolley

11. For automatic locking & for lifting of automatic twist lock how much force is Kg required

respectively?

(a) 600 & 1000 kg (b) 800 & 1200 kg (c) 1000 & 500kg (d) 500 & 1350kg

12. What is the loading capacity of containers in BLC wagon?

(a) Two 20 or one 40 (b) Two 22 or One 45 (c) Three 15 or Two 20 (d) Two 20 or One 45

13. Why platform height of BLC wagon is Kept lower than other wagon:

(a) To achieve high speed (b) To increase pay load(c) To accommodate 9’6” container (d) None of the

above

CNC MACHINE

1. CNC machining don’t include operation like:

2. (a) milling (b) boring (c) welding (d) tapping

2. Which of the following is not the advantage of CNC machines ?

(a) Higher Flexibility (b) Improved Quality (c) Reduced Scrap Rate (d) Improved Strength of the

components

3. For CNC machines skilled programmers are needed:

(a) True (b) False

4. CNC machining centre does all the work: (a) Milling Machine (b) Drilling Machine

(c) Both Milling & Drilling Machine (d) None of these

5. DNC stands for:

(a) Digital Numerical Control

(b) Direct Numerical Control (c) Double Numerical Control

(d) None of the above

6. A CNC machine find widest application in field of

(a) Small lot & batch production (b) Mass Production (c) Non Conventional Machining (d) None of the

above

7. CNC machine is not applicable in:

(a) drilling Machine (b) milling machine (c) lathe (d) None of the above

8. CNC machine has the following main advantage over conventional machine

(a) ability for higher cutting speed, feed & depth of cut (b) feedback control

(c) Flexibility (d) None of the above

9. On CNC lathe:

(a) 2-D Programming is sufficient (b) 3-D Programming is necessary (c) 1 -D Programming is

necessary (d) None of the above

10. CNC machine requires ________in comparison to conventional machine.

(a) Less Man Power (b) More Man Power (c) Same Man Power (d) None of the above

11. Full Form of CNC machine is: (a) Central Numeric Control (b) Computer Number Control

(c) Computer Numeric Control (d) Computer Numeric Centre

WELDING

1. Which of following have high corrosion resistance:

(a) Welding Joint (b) Rivetted Joint (c) Bolted Joint (d) None of the above

2. Which of following ray is not produced during welding

(a) Gamma rays (b) Visible light ray (c) Infrared ray (d) Ultra Violet Ray

3. Which of following is an example of plastic welding

(a) Gas Welding (b) Arc Welding (c) Forge Welding (d) Thermit Welding

4. Which of the following is an example of fusion welding____:

(a) Arc Welding (b) Forge Welding (c) Resistance Welding (d) Thermit Welding with Pressure

5. The Temperature of arc in case of arc welding:

(a) 2000˚C (b) 2600˚C (c) 3000˚C (d) 3600˚C

6. Which of following welding procures uses non-consumable electrode:

(a) Gas Tungsten arc Welding(TIG)

(b) Shielded metal arc welding

(c) CO2 Shielded Welding

(d) Gas Metal Arc Welding(MIG)

7. In arc welding the three elements to be controlled to obtain satisfactory welding operation are:

(a) current, voltage & speed of travel (b) current, voltage and arc length

(c) current , arc length and speed of travel

(d) voltage ,arc length and speed of travel

8. Arc length in arc welding should be nearly equal to_______

(a) Diameter of electrode rod(d) (b) 1.5 d (c) 2 d (d) 3 d

9. Too low welding current in arc welding would be result in________

(a) Excessive pilling of weld metal, poor penetration, wasted electrodes

(b) Excessive Spatter, under cutting along edge

(c) Too small beads, weak weld and wasted electrodes

(d) None of the above

10. To high welding current in arc welding would result in ______________

(a) Excessive pilling up of weld metal, poor penetration , wasted electrodes

(b) Excessive spatter, under cutting along edges, irregular deposit, wasted electrodes (c) Too small ,weak weld and wasted electrodes

(d) None of the above

11. Which type of electrode is used in submerged arc welding

(a) Bare rods (b) Coated electrodes (c) Core wires (d) Copper Electrodes

12. Following welding process uses consumable electrodes

(a) TIG (b) MIG (c) Thermet (d) Gas

13. Preheating is essential in welding for

(a) High speed Steel (b) Stainless Steel (c) Cast Iron (d) German Silver

SAFETY

1. Decible (db) is a unit to measure

(a) Light (b) Sound (c) Frequency (d) None of these

2. Following is (are) generally provided with limit switches to prevent motion beyond present limit:

(a) Hoists (b) conveyors (c) Machine tables (d) All of the above

3. The following is (are) used in safety devices in machines:

(a) Fail safe (b) Safety interlocks (c) Limit Switches (d) All of the above

4. Class-‘A’ fire consists of the fire are to :

(a) Wood (b) Oil (c) Transformer (d) Chemical

5. Water is used to extinguish:

(a) Class A fire (b) Class B fire (c) Class C fire (d) All of the above

6. Following class of fire Occurs in electrical equipments

(a) Class A fire (b) Class B fire (c) Class C fire (d) All of the above

7. Following extinguisher is suitable for cotton or other textile fire:

(a) Water (b) Soda acid (c) Foam (d) Dry Chemicals

8. ________is best suited to extinguish oil or flammable liquid fire:

(a) Soda acid (b) Vaporizing Liquid (c) Foam (d) Dry Chemicals

9. Fire is a combination of :

(a) Fuel, Light and Oxygen

(b) Fuel, Heat and Oxygen (c) Fuel, Heat and Carbon dioxide

(d) Fuel, Light and Nitrogen

10. Safe Way of Working is:

(a) an effective and right way of working (b) an ancient way of working

(c) a way of handling the work in a hurry

(d) a way of normal working

MAINTENANCE & PRODUCTION

1. Maintenance consists of the following action:

(a) Replace of Components (b) Repair of Components (c) Service of Components (d) All of the above

2. With the increase in preventive maintenance cost, breakdown maintenance cost

(a) Increases (b) Decreases (c) Remain same (d) None

3. The Resources utilized for production are:

(a) Manpower , Material, Machines (b) Methods , Material, and Machines

(c) Methods, Machine, and Manpower

(d) Methods , Machine, Material

4. Preventive Maintenance improves

(a) Material Productivity (b) Labour Productivity(c) Machine Productivity (d) Capital Productivity

5. Productivity can be increased by :

(a) By increasing the output from the same input

(b) By Reducing the input for the same output

(c) Both A & B

(d) None of these

6. Productivity_______________?

(a) Input /Output (b) Output/Input (c) Output-Input (d) Input-Output

FULL FORM

1. DA – Dearness Allowance

2. HRA - House Rent Allowance

3. CCA -City Compensatory Allowance

4. PLB - Productivity Linked Bonus

5. PPE - Personnel Protective Equipments

6. OTP - Overtime Payment/One Time Password

7. GIS - Group Insurance Scheme

8. NPS - New Pension Scheme

9. NEFT - National Electronic Fund Transfer

10. RTGS - Real Time Gross Settlement

11. MICR - Magnetic Ink Character Recognition

12. IFSC - Indian Financial System Code

13. PF - Provident Fund 14. LIC - Life Insurance Corporation

ESTABLISHMENT RULES

1. How many sets of School pass issued to Railway Employee?

(a) 6 sets per year (b) 4 sets per year (c) 3 sets per year (d) 5 sets per year

2. Maximum validity for a privilege pass

(a) 3 months (Half set) (b) 4 months (full sets) (c) 2 months (half set) (d) 5 months (Full sets)

3. Attendants of pass holder is: (a) Part time servant (b) Servant (c) Full time paid servant (d) Any

person

4. Full form of PTO_________

(a) Personnel Ticket order

(b) Permanent Ticket Order

(c) Privilege Ticket Order

(d) Pass & Ticket Order

5. Break Journey is not permissible in case of ____

(a) Transfer Pass (b) School Pass (c) Settlement Pass (d) Post Retd. complimentary pass

6. How much service (minimum) is required for post retired complimentary pass

(a) 20 years (b) 25 years (c) 15 years (d) 33 years

7. Who is the Authority to grant study leave abroad?

(a) Railway Board (b) GM (c) DRM (d) CPO

8. Who is the competent Authority to grant study leave within India:

(a) Railway Board (b) GM (c) DRM/CWM (d) CPO

9. Commuted leave is admissible on

(a) Medical certificate (b) Request of an Employee (c) Discretion of competent authority (d) None of the

above

10. Staff of which Railway are entitled to avail extra casual leave

(a) SER (b) ECOR (c) NFR (d) ECR

11. Within Which period paternity leave can be granted :

(a) Six months (b) three months (c) Four months (d) 15 days

12. Paternity leave is also admissible to -----

(a) Casual leave (b) Casual labour with temporary status (c) After completion of 180 days of service

(d) After regular absorption

13. What is the maximum period of leave on average pay at time that a Railway servant may be granted?

(a) 120 days (b)160 days (c) 180 days (d) 300 days

14. Who is the authority to sanction special disability leave?

(a) Senior Scale Officer (b) JA Grade Officer (c) DRM (d) ADRM

15. Maximum encashment of leave on average pay is__

(a) 200 days (b) 60 days (c) 360 days (d) 300 days

16. When no leave is admissible under any other rule the leave granted is known as______

(a) LAP (b) LHAP (c) SPL leave (d) Extra ordinary leave

17. Which of the following category is entitled for hospital leave:

(a) Group ‘A’ (b) Group ‘B’ (c) Group ‘C’ (d) Group ‘D’

18. Study leave shall count for :

(a) Reckoning Seniority (b) Reckoning increment (c) Earning LAP (d) Earning LHAD

19. A male railway servant may be granted paternity leave having surviving children:

(a) Less than two (b)One (c) Four (d) Three

20. How many days of LHAP can be accumulated to an employee in his service life

(a) 300 days (b) 450 days (c) 600 days (d) Unlimited

21. LAP shall be credited to a Railway servant at the rate of :

(a) 2-1/2 days per month (b) 3 days per month (c) 2 days permanent (d) 1-1/2 days per month

22. Maximum days of leave on average pay that can be accumulated is :

(a) 120 (b) 180 (c) 190 (d) 300 23. New Pension scheme is effective from:

(a) 01-01-2004 (b) 01 -07-2004 (c) 01 -04-2004 (d) None of these

24. New Pension Scheme is _________

(a) Contributory (b) Non Contributory (c) None (d) All of the above

25. The contribution payable by one employee:

(a) Monthly basis (b) Quarterly basis (c) Half Quarterly basis (d) Yearly basis

26. The contribution towards new pension scheme is :

(a) @8% of pay (b) @9% of pay (c) @ 10% of pay (d) @12% of pay

27. Dearness Allowance is to be taken with pay for contribution______

(a) Yes (b) No (c) Partly true (d) Partly wrong

28. Permanent Pension Account number will consist of :

(a) 12 digits (b) 14 digits (c) 16 digits (d) 20 digits