Upload
lexus-pasley
View
219
Download
0
Tags:
Embed Size (px)
Citation preview
MediaStar Compact Training Slides Rev. E
Introduction to MediaStar Compact
• Maximum of 16 channels only• Over Cat5/5e & 6 cable• Composite output from receive
units
How does Compact distribute video:
• RCU control at user position• Browser, IP or RS232/485 central control
How does Compact manage the distribution of video:
• Composite video sources• RF Sources (optional)• Cat5 etc Cable infrastructure• Displays with Composite video Input
What are the system requirements:
MediaStar Compact Training Slides Rev. E
Compact – Connectivity
A/V Cable
Remote Transmitter
Unit
MediaStar Compact Video Hub
DVD Unit
Satellite Decoder Unit
Display
Receive Unit
Cat5 Structured Cabling
A/V Cable
I/R Blaster
I/R Blaster
I/R Receiver
MediaStar Compact RCUSatellite Decoder Unit RCU
RF Input
DVD Unit RCUDuplicateDisplay
Recieve Unit
MediaStar Compact Training Slides Rev. E
Hub Details
740 MediaStar Compact Video Hub supporting 16 users,16 Composite channel inputs, IR routing743 MediaStar Compact Video Hub supporting 16 users,16 Composite channel inputs, IR routing
and 2 x 4 Duplicate output capability and 8 Remote Video inputs
Versions:
Versions:R indicates a system with an RF tuner board installed
MediaStar Compact Training Slides Rev. E
MediaStar Compact Video Hub – Fascia and backplane
A B C D E F G H I J K L M N O PVIDEO
OUTPUTS A-P
DUPLICATE OUTPUTS of A/EDUPLICATE OUTPUTS of A 1/9 2/10 3/11 4/12 5/13 6/14 7/15 8/16REMOTE INPUT
CHANNELSRF INPUT
CHANNELSPOWER
1 – 89 - 16
16 RJ45 Output sockets labelled “A” to “P”
743 Compact Video Hub only8 duplicate RJ45 Output sockets, options are:• All 8 duplicate of outlet A• 4 duplicates of outlet A and 4 duplicates of E
743 Compact VideoHub only8 remote video feed RJ45 Input sockets, options are:• Set as channels 9-16 (default)• Set as channels 1-8
Input configuration LEDs
Power LED
Power InputLocal video source
inputsSerial Link
IP LinkIR Links
Multiple Hub Link V-Bus and comms connectors
RF Input(if fitted)
PAL/NTSC Switch Spare Fuse
MediaStar Compact Training Slides Rev. E
MediaStar Compact Video Hub – Rackmounting
Rack MountingThe MediaStar Compact Video Hub is supplied with 19” rackmount brackets.Once the rack mounting brackets are fitted, mount the Hub into the cabinet or closet using the screws supplied with the Rack Mount Kit
Power connectionOnce the Hub is mounted in the cabinet, connect the Hub to an AC power supply using the IEC Power Lead suppliedOnce the lead is connected the Hub will power on automatically
MediaStar Compact Training Slides Rev. E
Video format selection
• Set the video format required, PAL or NTSC, depending on your video sources
• The switch can be found at the rear of the Hub, located next to the 64 V-Bus Connector
• PAL = Upper position, NTSC = Lower position
MediaStar Compact Training Slides Rev. E
Local video sources
• Across the back of the Compact Video Hub is a bank of phono RCA connectors labelled 1 to 16
• For each local video source, the audio and video connectors must be plugged into the appropriate connectors on the hub
• The source will appear on the channel as labelled by the video input connector (1 to 16)
MediaStar Compact Video Hub
Local A/V source
Display
Recieve Unit
Cat5 Structured Cabling
A/V Cable
I/R Receiver
MediaStar Compact RCU
MediaStar Compact Training Slides Rev. E
Connecting local video sources
• Connect the source video device to the relevant audio and video inputs located at the rear of the Compact Video Hub
• The video input is at the top (yellow), with the left audio connector in the middle (white) and the right audio connector at the bottom (red)
• Ensure that the correct left and right audio feeds are connected
MediaStar Compact Training Slides Rev. E
Connecting local video sources – 2 Channel example
• The DVD unit is connected to input 1 and will appear to users as channel 1
• The Satellite Decoder is connected to input 2 and will appear to users as channel 2
• The channel name displayed to the user can be edited
The example below shows two video sources, a DVD and Satellite decoder unit, connected to the Compact Video Hub.
VIDEO L
R
IN
VIDEO LRIN
OUT
R
Compact Video Hub
DVD
Satellite Decoder
Dish input
RF Output
Input 1Input 2
MediaStar Compact Training Slides Rev. E
MediaStar Compact Video
Hub
Local A/V source
Display
RX UnitCat5 Structured Cabling
A/V Cable
I/R Blaster
I/R Receiver
MediaStar Compact RCU
Local A/V source RCU
Some TV channel sources (Satellite Decoder, DVD, etc) can be controlled using infrared remote control units. The IR routing feature of the MediaStar Compact System allows users to control these devices using the devices own RCU at the Compact Receive Unit position.
• When the user selects a Compact TV channel, an IR ‘path’ is set up between the receiver in the Recieve unit and the TV channel source
• The IR blaster module (part no.911-4147) itself is positioned over the IR receiver on the remote channel source device and connected to the Compact Video Hub via IR blaster drive connectors located at the rear of the hub
• There are a total of 16 IR blaster connectors available, one for each input availableNote: the Compact Video Hub is supplied with 1off 911-4147 Blaster module
Local video source IR routing
911-4147 IR blaster
Versions:
MediaStar Compact Training Slides Rev. E
Connecting a local video IR source
Compact Video Hub
DVD
Satellite Decoder
This example shows two video sources, a DVD and Satellite decoder unit and their respective IR routing, connected to the Compact Video Hub.
If the local or remote video source unit can be controlled with a 38KHz modulated IR remote control, an IR blaster is connected to the 2 pin polarised IR blaster connector on the backplane of the hub to the devices IR source.
Note: Some IR control equipment uses different modulation techniques or frequencies and cannot be controlled through the MediaStar Compact System.
• The IR blaster head must be carefully fitted over the video source unit’s own IR receiver • Care must be taken to ensure that the adhesive pad on the IR blaster head does not
damage the surface of the unit• If the video source unit responds to IR commands intermittently, or does not respond at
all, the power of the IR emitted by the blaster may need to be adjusted• Power is adjusted by turning the small screw on the outward facing side of the IR
blaster
MediaStar Compact Training Slides Rev. E
751 Video Receive Unit
On the front of the Compact Video Hub there are 16 RJ45 sockets, labelled ‘A’ to ‘P’. The Video Receiver Units (part no. 751) are connected to these outlets with up to 400m of Category5 cabling. The users connected to these outlets are able to independently select any one of the 16 channels available.
• The Audio/Video (A/V) output cable provides the video signal and left and right audio signals to the TV, plasma display or PC graphics card on male phono connectors.
• The Video Adjustment control should be set to provide optimum video picture quality. This can be done by viewing the picture or using video test equipment as required.
Underside view
751 Receive Unit
Versions:
Power/IR Receive LED
Rear view Front view
Video Network Connection
Remote IR Receiver Socket
Video Adjustment
A/V Output Cable
VideoNetwork
IRRecvr
VideoAdj S
L
VideoNetwork
IRRecvr
VideoAdj
MediaStar Compact Training Slides Rev. E
790/1X Remote Control
The 751 Receive unit is not supplied with the 751 Receive Unit and needs to be ordered separately.You will need the Remote Control Unit to:
•Change Compact channels
•Change volume
•Access on-screen information and menu options
790/1X Receive Unit
Versions:
MediaStar Compact Training Slides Rev. E
IR Receiver
An integrated IR receiver is located at the front of the MediaStar Video Receiver Unit. When the unit receives any IR command from the Compact remote control unit (RCU), the LED on the unit will flash.
Remote IR Receiver
Video Receiver
Unit
• If the MediaStar Compact Video Receiver Unit is to be positioned where the IR receiver will not be visible, a remote IR receiver module (part no.911-4141) can be plugged into the Remote IR Receiver connector.
• This can then be positioned discretely on the display unit, visible to the remote control unit.
• The internal IR receiver in the Video Receiver Unit will be disabled.
• When positioning a remote IR receiver, ensure that the surface where it is located will not be affected by the adhesive on the IR receiver.
Compact RCU
Compact Video Hub
MediaStar Compact Training Slides Rev. E
Configuring Hub details
Using the MediaStar Compact IR remote control unit you can configure severaldifferent settings on the Compact Video Hub, these include:• View current settingsInformation given includes hub name, outlet label, software version, TV standard and channel input sources• Compact Video Hub nameChange the current hub name, default is “Video Hub 1”• Channels namesSet the displayed name for specific channels• Set New PasswordChange the current password required to access the configuration options, default is “000000”• Define Duplicate Outlet SourceDefine whether the second set of four duplicated outlets are duplicates of Outlet A or Outlet E, select Menu/Settings/Duplicate Source• Define Tuner SettingsWhere internal tuners are fitted in the hub, the type of RF input into the hub must be defined. The channel and frequency for each tuner must then be defined
MediaStar Compact Training Slides Rev. E
Configuring Hub details (continued)
• Define Serial Comms ModeIf the hub is to be controlled by an external unit using the serial comms port, the mode of communication must be set up.•Set IP DetailsIn order to communicate with the hub over a 10BaseT LAN, the network IP settings must be configured.• Set Screen Background ColourUse this option to change the background colour of the screen used for menus, select Menu/Settings/Screen Colour. • Set Channel AccessUser access can be restricted to specific channels
Please consult the MediaStar Compact User Guide for further details.
MediaStar Compact Training Slides Rev. E
Category 5 Cable connectivity for 751 Units
The MediaStar Compact system uses the Cat5 4pair structured cabling for the transmission of composite video/audio streams and control signals to individual users.
Pin 1
Typical RJ45
Pin 8
Pair RJ45 Pins 568B Colour Spec. Usage1 4&5 Blue & Blue/White Audio Left/+12V2 1&2 White/Orange & Orange Audio Right/-12V3 3&6 White/Green & Green Communications/IR & Grd4 7&8 White/Brown & Brown Video Downstream
• The maximum distance from Hub to user location must not exceed 400 metres (1200 feet) for Cat 5 UTP.
MediaStar Compact Training Slides Rev. E
764 Compact-Evolution Interface UnitThis unit provides an interface between the MediaStar Evolution DVI Endpoint and a MediaStar Compact TV distribution system. It takes a standard Compact TV feed and converts it to a format that can be input into the MediaStar Evolution Endpoint. The Evolution Endpoint can then use the Compact video and audio signals as a TV source that can be scaled and presented on any of the Endpoint’s output options. 764 Interface Unit
Versions:
• The Compact 751 Receive Unit in NOT required as the feed from the Compact Hub connects directly to the Interface Unit
Compact Video Hub
DisplayCat5 Structured Cabling
I/R Receiver
Compact RCUEvolution 760 or 760/xM Endpoint with 764 Interface Unit fitted
MediaStar Compact Training Slides Rev. E
753 RS232 to IR Converter
• The RS232 To IR Adapter (part no.753) provides a serial control
interface for MediaStar Compact Video Receiver Units.
• Cabletime provides the Mediastar Viewer PC based software application that works with this converter unit to control the selection of TV channels.
• You can, if you wish to use your own hardware or software for channel control.
• This unit is powered from the Video Receiver Unit or Micro Settop, and requires no external power supply.
The RS232 To IR converter is connected between an asynchronous serial communications port (typically COM1 on a PC) and the Remote IR Receiver socket of the Video Receiver Unit or Micro Settop unit. When the converter receives a specific ASCII character followed by a carriage return (<CR>), it transmits a series of electrical pulses into the Video Receiver Unit or Micro Settop unit. These pulses imitate the output from a Remote IR receiver when it sees IR from an RCU key press. The Video Receiver Unit or Micro Settop then responds to those RCU key presses in the usual way.• The serial interface operates using half duplex asynchronous serial communications, at
9600 Baud, with 1 start bit, 8 data bits, and 1 stop bit. There is no hardware handshaking.
• On the 9 way D connector, pin 2 is RX data, Pin 3 is TX data and pin 5 is signal ground.
• All other pins are not connected.
753 RS232 to IR Converter
Versions:
MediaStar Compact Training Slides Rev. E
Compact Viewer
• The application allows PC users to select the channel to view, and adjust the volume setting.
• It also provides access to all the on-screen setup menus that can be shown on a TV screen.
• The Viewer application requires video hardware that has the relevant “Video for Windows” drivers.
• Multiple copies of the Viewer application can be run simultaneously on a Desktop to enable control of several display devices.
• If the user wishes to create their own control application for the Video Receiver Unit, the serial communications protocol for the Mediastar RS232 to IR converter is available.
As well as controlling the MediaStar Compact System with a Remote Control Unit (RCU), you can control it from a PC, using the MediaStar Compact Viewer software application.
Please consult the MediaStar Compact User Guide for further details.
MediaStar Compact Training Slides Rev. E
RS232 to IR Converter switch closure inputs
This RS232 to IR Converter unit has four switch contact inputs to support external Channel up/down and Volume up/down keypads.
• The switch inputs are on 4 pins of the 753’s 9 way D connector (see table below)
• When a switch contact closure is made, the appropriate input pin should be shorted to pin 5 (ground) of the 9 way D connector
753 9 way D TypeFemale Connector
Optional PC Serial 9 way D Connector
ButtonChannel Up
ButtonChannel Down
1
9
1
9
• Switches must be of the ‘normally open’ type. If a switch (button) is held closed (pressed), the button press will auto-repeat after a short pause
• Only one button should be pressed at a time. If more than one button is pressed, all buttons will be ignored
• If a suitable 9 way D lead is produced, this unit can accept serial commands from a control system and switch closure inputs at the same time
• If these switch inputs are not required, the unit can be connected to a computer using the supplied 9-way cable as usual
Function pinChannel Up (U) 8Channel Down (D) 1Volume Up (+) 9Volume down (-) 6Signal ground 5Serial TX 2Serial RX 3
Example
MediaStar Compact Training Slides Rev. E
IR Converter Connectivity options
Compact Video Hub
Display
751 Video Receiver Unit
751 Video Receiver
Unit
PC Running MediaStar Compact Viewer
753 Converter
Video Capture and Audio Cards
753 Converter Connected to COM1
Cat 5 Structured
Cabling
Audio & Video Lead
Audio & Video Lead
Wall mounted touch panel
MediaStar Compact Training Slides Rev. E
Duplicate outputs (743 Compact Video Hub Only)
• The Duplicate outlets consist of two groups of 4 RJ45 Sockets (743 Hub versions only)
• The left group of 4 sockets are duplicates of Outlet A
• The right group of 4 sockets can be configured via setup menus to be duplicates of Outlet A or all duplicates of Outlet E
• This provides either 2 groups of 5 identical outputs or 1 group of 9 identical outlets
• Any Video Receiver Units connected to Duplicated Outlets are able to make channel changes
• Any channel change made will affect all the outlets that have been grouped together, including Outlet A or Outlet E
743 MediaStar Compact Video Hub
RX Unit
Cat5 Structured CablingDuplicate
Display 4
DuplicateDisplay 8
RX Unit Display, outlet A
MediaStar Compact Training Slides Rev. E
Remote video sources (743 Compact Video Hub Only)
A/V Cable
Remote Transmitter
Unit
Remote A/V SourceCat5 Structured Cabling
• Up to 8 remote video sources can be connected via CAT5 cabling to the hub (743 Hub versions only) using the remote video inputs located on the front of the hub
• The maximum distance from the Transmit Unit to the Hub via Cat5 cable is 400 meters
• Although hubs are fitted with 8 remote video inputs, any unused (unconnected) remote input may be used for rear panel local video inputs
743 Compact Video Hub
MediaStar Compact Training Slides Rev. E
Remote video source IR routing (743 Compact Video Hub Only)If the video source unit can be controlled with a 38KHz modulated IR remote control, an IR blaster is connected to the 2 pin polarised IR blaster connector on the Remote Video Transmitter.
• Ensure IR blaster head is then carefully fitted over the
video source unit’s own IR receiver.
• Ensure care is taken to ensure that the adhesive pad on the
IR blaster head does not damage the surface of the unit.
• If the video source unit responds to IR commands
• intermittently, or does not respond at all, the power of the IR emitted by the blaster may need to be adjusted.
• The power is adjusted by turning the small screw on the outward facing side of the IR blaster head
Note: Some IR control equipment uses different modulation techniques or frequencies and cannot be controlled through the MediaStar Compact System.
A/V Cable
Remote Transmitter Unit
Remote A/V source
DisplayReceive Unit
Cat5 Structured Cabling
MediaStar Compact RCU
Remote A/V source RCU
IR Blaster
743 Compact Video Hub
MediaStar Compact Training Slides Rev. E
752 Remote Transmitter Unit (743 Compact Video Hub Only)
• The transmitter is powered from the hub• The LED will show orange when it is connected
• The A/V sources are connected to the phono inputs on the transmitter unit
• When a video input signal is detected, the Remote Video Transmitter LED will show green
VideoAdjS
L Video Left audio Right audio
Video Adjustment
Left Audio Input
Right Audio Input
Video Input
IR Blaster Socket
VideoNetwork
Power
RJ45 Video Network Connection
Power/Video Input LED
• The video adjustment screw on the Remote Video Transmitter is turned to give the best picture quality
The Remote Video Transmitter (part no.752) is connected to the 743 Compact Video Hub via the CAT5 structured wiring system (up to 400m away).
752 Remote Transmitter Unit
Versions:
MediaStar Compact Training Slides Rev. E
Category 5 Cable connectivity for 752 Units
The MediaStar Compact system uses the Cat5 4pair structured cabling for the transmission of composite video/audio streams and control signals remote transmitters.
Pin 1
Typical RJ45
Pin 8
Pair RJ45 Pins 568B Colour Spec. Usage1 4&5 Blue & Blue/White Audio Left/+12V2 1&2 White/Orange & Orange Audio Right/-12V3 3&6 White/Green & Green Communications/IR & Grd4 7&8 White/Brown & Brown Video Downstream
• The maximum distance from Hub to remote location must not exceed 400 meters (1200 feet) for Cat 5 UTP.
MediaStar Compact Training Slides Rev. E
Connecting an RF feed
• The RF feed is connected via an ‘F’ type connector located on the rear face of the unit• The MediaStar Compact Video Hub tuner module supports PAL or NTSC standards• The MediaStar Compact Video Hub tuner module supports a frequency Range of 48 to
862MHz
RF Connector
If your MediaStar Compact Video Hub is fitted with a tuner module (R Suffix), up to 8 off-air or CATV RF sources can be used by the hub. Although hubs are fitted with blocks of 8 tuners, any unused (switched off) tuner source channels may be used for local video inputs instead.
ConfiguringWhere RF tuners are fitted in the hub, you must use the remote control unit or IP Browser interface to define RF input levels and tuner frequency settings.
MediaStar Compact Training Slides Rev. E
Defining Input Settings
Where RF tuners are fitted in the hub and/or remote video sources are used these are defined as either channels 1-8 or 9-16.At the front of the hub are LED’s which indicate the hubs current configuration.
Off
Orange
Green
Red
No tuner card fitted
RF inputs set up for channel bank 1 to 8
RF inputs set up for channel bank 9 to 16
There is a clash of channel bank settings between RF source and remote video source. Refer to Installer/Manufacturer.
RF Input Channels
Orange
Green
Red
Remote video inputs set up for channel bank 1 to 8
Remote video inputs set up for channel bank 9 to 16
There is a clash of channel bank settings between local and remote video source. Refer to Installer/Manufacturer.
Remote Input Channels (743 Only)
• When an RF tuner board is installed the RF sources will be configured as channels 1-8 and the remote video sources as channels 9-16.
• To set these RF sources as channels 9-16 on the video hub you will need to configure the video hub internally, please consult with Cabletime Limited regarding this.
P
8/16
POWER
REMOTE INPUT CHANNELS
RF INPUT CHANNELS
1-89-16ONM
7/156/145/13
MediaStar Compact Training Slides Rev. E
Multiple Hubs
A/V Cable
Remote Transmitter
Unit
MediaStar Compact Video Hubs
DVD Unit connected to Hub#2
Satellite Decoder Unitconnected to Hub#1
RX Unit
Cat5 Structured Cabling
A/V Cable
I/R Lead
I/R Lead
MediaStar Compact RCU
DVD Unit RCU
DisplayConnected to
Hub #1Display
Connected to Hub #2
RF input to Hub#1
MediaStar Compact RCU
Satellite Decoder Unit RCU
RX Unit
MediaStar Compact Training Slides Rev. E
Multiple Hubs Setup• Up to 4 hubs can be linked together, providing a 64 user, 16 Channel system.
• When the hub link connector is fitted it allows changes in channel configurations to be shared between the hubs, for example a new channel name.
• The V bus ribbon cable and hub link cables are supplied as a Multiple Hub Configuration Kit, available from your reseller or Cabletime.
• There can only be one source for each of the 16 TV channels. That source may be fed into any of the connected hubs.
• For systems where 16 remote video sources are required, one hub will be configured with remote video inputs on channel bank 1 to 8 and the second video hub must be configured with remote video inputs on channel bank 9 to 16.
• Similarly, if more than 8 RF source channels are required the RF source
must be externally split and fed into two video hubs with the RF tuner
sources configured on channel bank 1 to 8 on one hub and channel bank
9 to 16 on the second hub.
• To enable users on different hubs to remotely control local
video sources with IR RCUs, the rear panel IR drive connectors
on each hub must be linked together using a multi hub IR
drive cables747/2 2 Hub Link Kit747/4 4 Hub Link Kit
Versions:
MediaStar Compact Training Slides Rev. E
Multiple Hub Connectivity
VIDEO L
R
IN
DVD
Satellite Decoder 1
VIDEO LRIN
OUT
R Satellite Decoder 2
Dish input
RF Output
VIDEO LRIN
OUT
R Dish input
RF Output
• This diagram shows a Dual Hub system with 13 RF & 3 local Channels and IR control of channel 9 (Satellite decoder 1) for all users.
Compact Video Hub #1
Compact Video Hub #2
V Bus Ribbon Cable
Hub Link Connector
Multi hub IR drive cable
RF Input(Channels 1-8)
RF Input(Channels 12-
16)
MediaStar Compact Training Slides Rev. E
External Control of Compact Video Hubs
• Before any external commands are executed using IP, RS232 or RS485 links, the control feature of the hub must be enabled.
• If serial or IP control is disabled, an enablement code must be obtained from your installer or Cabletime. This code is then entered using the Feature Enablement menu option.
21
WARNING: HAZARDOUS VOLTAGE INSIDENO OPERATOR SERVICABLE PARTS INSIDE
HUBLINK
10 BT
NIC
IRDRIVE
1
9
RF IN V-BUS
Serial Connection IP Connection
Rear view of Compact Video Hub
Please consult the MediaStar Compact User Guide for further details.
External devices such as Crestron or AMX control units can control MediaStar Compact Video Hubs. The external devices send text-based commands to the hub, using an IP, RS232 or RS485 communications link. The hub then actions the commands and returns an appropriate status message indicating whether the command was executed successfully.
MediaStar Compact Training Slides Rev. E
Browser Control
The Mediastar Compact Video Hub can be configured and controlled remotely over a 10BaseT IP network link using standard browser software (e.g. Microsoft Internet Explorer 5.0 onwards or Netscape 6, both with Javascript V1.1 support). If utilising IE8 please use the IE7 Emulation mode.• Browser control of the hub is an optional feature that must be enabled before use. To
check whether it is enabled, press the INFO button twice on the MediaStar Compact remote control unit. ‘Browser’ will be shown as either ‘enabled’ or ‘disabled’.
• The hub must be configured with a static IP address and subnet mask prior to connection onto the LAN.
• When a network link is established, the green IP Link LED on the rear of the hub will be illuminated. When the hub sees network traffic addressed to it, the LED will flash.
• On the controlling PC, start up the standard browser software. In the address field, enter the IP address of the hub in the following format:
http://<IP address of hub>
eg http://191.53.51.206
• After a short pause, the ‘Enter Network Password’ window appears. If the window does not appear it may be that the password has not been set.
• After entering the username and password the MediaStar Compact Video Hub specification page will be displayed.
MediaStar Compact Training Slides Rev. E
Hub specification
Information Hub Control Settings Admin Password
On the left hand side of the window, there is a selection of controls:
Click on each of these items to show the controls available. The structure of these controls is similar to the on-screen configuration menus.
MediaStar Compact Training Slides Rev. E
Hub information
Hub name Hub part no: Hub serial no: Hub software version TV standard Channels 1-8 and 9-16
configuration Serial control option Browser option The outlet source for the
duplicate outlets (743 Only)
This displays information regarding the Compact Video Hub, including:
MediaStar Compact Training Slides Rev. E
Channel changes page
Select an outlet between A and P
Select the channel to be viewed between 1 and 16
Select submit
This command is used to change the channel being viewed by an outlet.
The outlet selected will then view the specified channel.
MediaStar Compact Training Slides Rev. E
Remote Volume Control
Select the volume action:
Select an outlet between A and P
Mute Unmute Increment Decrement Enter the volume setting
if required Select submit
This command is used to change the volume setting of an outlet.
The outlet selected will then change to the specified volume setting.
MediaStar Compact Training Slides Rev. E
Set Hub Name
This command is used to change the Hubs name.
Enter the new hub name Select submit
MediaStar Compact Training Slides Rev. E
Set Channel Names
Select the channel Enter the new channel
name Select submit
This command is used to set the channel names.
The channel selected will then change to the specified setting.
MediaStar Compact Training Slides Rev. E
Set Duplicate Outlet Source
Select the source outlet
A or B Select submit
This command is used to set the duplicate outlet sources.
The source selected will then change to the specified setting.
MediaStar Compact Training Slides Rev. E
Set Outlet Background Colour
Select an outlet Select the required
background colour Select submit
This command is used to set the outlet background colour.
The outlet selected will then change to the specified colour setting.
MediaStar Compact Training Slides Rev. E
Channel Access Control
These pages are used to set users channel access permissions: Select the required
channels Select submitThe channel selected will then be available to the relevant user.
MediaStar Compact Training Slides Rev. E
Set Serial Control Comms Mode
Select the serial communications mode if applicable:
RS232 or RS485 Select Submit
This page is used to set the serial communications mode :
The channel mode will then be available to the relevant control device.
MediaStar Compact Training Slides Rev. E
Tuners
Switch tuner channel ON or OFF
Set the frequency of individual channels
Select Submit
This page is used to set the tuners if installed:
The tuner status and frequency will then be set.
MediaStar Compact Training Slides Rev. E
RF Input Level
Select either Antenna Amplifier
or CATV feed Select Submit
This page is used to set the tuners RF input level, if installed:
The RF Input level will then be set.
MediaStar Compact Training Slides Rev. E
Set Menu Password
Create or reset the system password
If the password field is left blank, no password is required in future
Select Submit
This page is used to set a new Menu password:
The new password will be set.