Medical Vacuum Systems: Lubricated Vane - Allied ... · GENERAL Product Specification The Chemetron® medical vacuum system is designed to create a suction system to remove unwanted

Product Specification

GENERAL The Chemetron® medical vacuum system is designed to

create a suction system to remove unwanted fluids or

gases from hospital/laboratory working areas. The

medical vacuum system package is compliant with the

NFPA 99 requirements for medical vacuum. Note that

larger systems are shipped on 2 or more skids and require

connection of clearly labeled wiring and piping between

skids once they are mounted on-site.

MEDICAL VACUUM SYSTEM The package shall include multiple vacuum pumps and

associated equipment, one ASME tank and one medical

control panel. Each pump is factory piped to a common

intake manifold. The system shall be completely tested

prior to shipment. Vibration isolation pads are included

with the system.

ROTARY VANE VACUUM PUMP The medical vacuum pumps shall be of the rotary vane air

cooled design, and manufactured in the USA. Each

vacuum pump shall be direct-driven through a shaft

coupling by a TEFC electric motor. Belt drives shall not

be permitted. Each vacuum pump shall be air cooled and

have absolutely no water requirements. Each vacuum

pump shall have an end (ultimate) vacuum of 29.3" Hg

(15 torr). Lubrication shall be provided by an integral,

fully recirculating oil supply that is filtered by an

automotive-type, spin-on oil filter. Non-recirculating

(once-through) or partial recirculating oil supply systems

shall not be permitted. Each vacuum pump shall be

capable of operation with standard SAE 30 weight oil.

The oil separation systems shall be integral and shall

consist of no less than three stages of internally installed

oil and smoke eliminators through which the exhaust gas

stream must pass. This system shall consist of bulk

separation, oil mist elimination, and smoke elimination,

and shall be capable of removing 99.9+ percent of all oil

and smoke particles from the exhaust gas stream. Each

vacuum pump shall include a built-in anti-suck-back

valve, mounted at the pump inlet, and three sliding vanes.

Each vacuum pump shall be equipped with a 10 micron

inlet filter for removal of particulates. The vacuum

pumps shall be mounted on vibration isolators.

MOTOR The motor is continuous duty, NEMA rated, C-face,

TEFC, suitable for 208-230, or 460V, 3 phase, 60 hertz

electrical operation.

AIR RECEIVER The system shall include an ASME rated air receiver

rated for 200 psi MAWP. The tank shall be equipped with

a vacuum gauge, block and by-pass valves, and a manual

drain.

CONTROL PANEL The system shall include a UL listed control panel in a

NEMA 12 enclosure with the following accessories for

each pump: externally operable disconnect, magnetic

starter with 3-leg overload protection, Hand/Off/Auto

lighted selector switch, minimum run timer to prevent

short cycling of the pump, and hour meter.

Standard features shall also include a main power on

light, timed lead/lag pump alternation, a reserve pump-in-

use alarm with visual and audible indications, and duplex

control circuit transformers with fused primary and

secondary protection. All alarms shall have dry contacts

on a labeled terminal strip for remote alarm monitoring,

and an acknowledge pushbutton for horn silencing. The

lag vacuum pump shall be able to start automatically if

the lead vacuum pump fails to operate.

AVAILABLE OPTIONS

High discharge air temperature shutdown alarm with

visual and audible indicators and dry contacts

Oil temperature gauges

Internal tank lining for corrosion resistance

Tank sight gauge

Medical Vacuum Systems:

Lubricated Vane


Lubricated Vane


Duplex Lubricated Vane

Tankmount

1 - 10 hp

208V 230V 460V

DLV010-80T 1 4 4 80 2,546 70 10 10 6 730

DLV015-80T 1-1/2 7 7 80 3,819 70 11 11 7 730

DLV020-80T 2 11 11 80 5,092 70 14 14 8 835

DLV030-80T 3 17 17 80 7,638 70 19 18 10 894

DLV050-120T1 5 26 26 120 12,730 71 30 28 15 1,049

DLV050-120T2 5 38 38 120 12,730 71 35 32 16 1,077

DLV075-200T 7-1/2 52 52 200 19,095 79 44 43 23 1,727

DLV100-200T 10 77 77 200 25,460 81 55 53 28 2,165

No tes : 1 - HP and NFP A Sys tem Capacity is s ho wn with o ne o r mo re pumps in res erve per NFP A 99

2 - BTU/HR Levels a re s ho wn with res erve pump(s ) o n s tandby

3 - dB(A) is s ho wn with o ne pump in res erve per NFP A99

TANK

SIZEBTU/HR2 dB(A)3

LEVEL

SYSTEM

WEIGHT

SYSTEM F.L.A.


NFPA

System

Capacity

SCFM @

19" Hg

Each

MODEL HP1



Lubricated Vane


Vertical

1 - 3 hp



Lubricated Vane


Vertical

5 hp



Lubricated Vane


Basemount

7-1/2 - 25 hp



Lubricated Vane

Triplex Lubricated Vane

Basemount

5 - 10 hp



Lubricated Vane

Triplex Lubricated Vane

Basemount

15 - 25 hp



Lubricated Vane

Quad Lubricated Vane

Basemount

5 - 25 hp

All specifications are nominal and subject

to change without notice.

Warranty: See Allied Statement of Warranties for details.

© 2009 Allied Healthcare Products, Inc.®

1720 Sublette Avenue

St. Louis, MO 63110 USA

314/771-2400

800/444-3954 www.alliedhpi.com

ISO 13485: 2003

Construction Customer Service

USA: 800/444-3960

FAX: 314/771-7537

Canada/Mexico: 800/446-0552

FAX: 800/246-6201

International: 314/268-1683

FAX: 314/771-5183

Medical Vacuum Systems: Lubricated Vane

Form 62-00-3800 June 2009


Documents

Medical Vacuum Systems: Lubricated Vane - Allied ... · GENERAL Product Specification The Chemetron® medical vacuum system is designed to create a suction system to remove unwanted