Metallographic Sample Preparation and Examination

Prepared by:

Mahmoud R.M.Abusrea

Teaching Assistant, MDP Dept.

October ,2008

Objective

• Metallography and its application

• Study the microstructure of materials.

• Observe grain boundaries and phases

What is Metallography??

• Metallography is the science and art of preparing a metal surface for analysis by grinding,

polishing, and

etching

to show microstructual component.

Introduction

• Microstructure:

is the geometric arrangement of grains and the different phases present in a material.

• Grain Boundaries:

is the interface between two grains in a polycrystalline material where the crystal is disordered due to rapid change in crystallographic directions.

Facts

• Most engineering alloys are polycrystalline this means that each piece of a metal is made up of a great number of single crystals, or grains, each having a regular crystal structure (for example, FCC, BCC, or HCP).

• Materials specialists are interested to see the grain boundaries in order to estimate the grain sizes. The average grain size in metals is usually in the order of several to tens of micrometers, which can be measured only by the use of an optical or light microscope

Application

• Study and characterization of materials.

• Ensure that the associations between properties and structure are properly understood.

• Predict properties of materials.

• Design alloys with new properties.

• Check if the material has been correctly heat treated.

Safety Instructions

• Optical Metallography involves the use of etchants (standard solutions containing a variety of chemicals such as strong acids and solvents) which can be very corrosive and poisonous.

Safety

• You must wear gloves and goggles and handle the chemicals with extreme care.

• You must not have direct skin or eye contact with the etchants. Etchants must be used in well ventilated area.

• Do not try to smell the etchants.

Sample Preparation

Sectioning

Sectioning is the first step in the overall process of specimen preparation. It is a step that should be given considerable thought and care. Where the sectioning should be placed, and also the proper equipment to use should be considered.

Fracturing abrasive cut-Fracturing a piece can be accomplished by applying repeated blows or steady pressure; however, this method is not recommended for several reasons. First, fracturing seldom follows desired directions unless the sample is pre-notched; second, the material. fractured-surface usually requires significant coarse grinding to obtain a flat surface.

Sawing is perhaps the oldest met lab method of sectioning that is still used today. It can be accomplished with a hand-held hacksaw, but it can alter the microstructure

Abrasive Wheel Sectioning is The most popular method of sectioning is with abrasive cut-off wheels. Wheels made of silicon carbide, aluminum oxide, and diamonds are used in the sectioning process. With this type of

sectioning, the metallographer has more control over the conditions used

Mounting

• Mounting. Small samples can be difficult to hold safely during grinding and polishing operations, and their shape may not be suitable for observation on a flat surface. They are therefore mounted inside a polymer block or mount.

Mounting

• Cold mounting can be done using two components resins (epoxies) which are liquid to start with but which set solid shortly after mixing. it requires very simple equipment consisting of a cylindrical ring which serves as a mould and a flat piece which serves as the base of the mould. the sample is placed on the flat piece within the mould and the mixture poured in and allowed to set. Cold mounting takes few hours to complete.

Mounting

• Hot-mounting the sample is surrounded by an organic polymeric powder which melts under the influence of heat (about 200 C). Pressure is also applied by a piston, ensuring a high quality mould free of porosity and with intimate contact between the sample and the polymer.

Mounting

Grinding• Grinding is done using rotating discs covered with silicon carbide

paper and water.• There are a number of grades of paper, with 180, 240, 400, 1200,

grains of silicon carbide per square inch. 180 grade therefore represents the coarsest particles and this is the grade to begin the grinding operation. Always use light pressure applied at the centre of the sample.

• Wash the sample in water and move to the next grade, orienting the scratches from the previous grade normal to the rotation direction. This makes it easy to see when the coarser scratches have all been removed.

• After the final grinding operation on 1200 paper, wash the sample in water followed by alcohol and dry it before moving to the polishers.

Polishing

• The polishers consist of rotating discs covered with soft cloth impregnated with a pre-prepared slurry of hard powdery alumina particles (Al2O3, the size ranges from 0.5 to 0.03 µm).

• Begin with the coarse slurry and continue polishing until the grinding scratches have been removed. It is of vital importance that the sample is thoroughly cleaned using soapy water, followed by alcohol, and dried before moving onto the final stage. Any contamination of the final polishing disc will make it impossible to achieve a satisfactory polish.

• Examining the specimen in the microscope after polishing should reveal mirror like surface.

Etching

• The purpose of etching is two-fold.1.Grinding and polishing operations produce a

highly deformed, thin layer on the surface which is removed chemically during etching.

2. attacks the surface with preference for those sites with the highest energy, leading to surface relief which allows different crystal orientations, grain boundaries, precipitates, phases and defects to be distinguished in reflected light microscopy as demonstrated in Figure

Etching• Etching should always be done in stages, beginning with light

attack, an examination in the microscope and further etching only if required.

• If you overetch a sample on the first step then the polishing procedure will have to be repeated.

• The table below gives the etchants for alloys that will be examined in this experiment.

SampleEtchant

Al alloysKeller’s (2 ml HF +3 ml HCL + 5 ml NO3+ 190 ml water)

Cu-Zn alloy (brass)10 ml HNO3+90 ml water

Steel and cast ironsNital (2% HNO3 + 98% ethanol)

Grain Size Determination

• How to report an average grain size?• Draw few random straight lines through the

micrograph. • The grain boundaries intersecting each line are

counted.• The average grain size is obtained by dividing

the total length of the lines by the number of intersections taking into account the magnification used to produce the micrograph.